How to decorate a bathroom with plastic panels. Finishing the toilet with PVC panels: interesting ideas (photo). Assembly tools

The most difficult and crucial stage in the repair of a bathroom can be considered the finishing of walls and ceilings. Most often, toilets are sheathed plastic panels or covered with tiles. Sometimes bathrooms are also decorated with mosaics or decorative plaster on drywall.

AT individual cases lining can be used for sheathing or wooden panels. Of course, in order for all surfaces to eventually turn out to be neat, repairs should be carried out in compliance with certain technologies.

How to sheathe a bathroom with plastic panels

Modern wall panels are the most convenient material option for finishing a bathroom. The room sheathed with them will look quite modern and aesthetically pleasing.

Among other things, plastic panels are not at all afraid of moisture, are hygienic, and their cost is low. Thus, using them you can make a budget, but at the same time quality repair.

Preparatory activities

Before the start of the repair, an estimate is drawn up with the calculation of all necessary materials. Here is a small example of a bathroom renovation estimate:

How to calculate the cost of repairing a toilet

Of course, when repairing small toilet in an apartment with your own hands, such a detailed list is not necessary. But the cost of basic materials is still worth estimating.

Before you start PVC trim panels, all furniture is removed from the bathroom and household appliances. Plumbing can be left for the duration of the repair, but it is also better to dismantle and clean it. Moreover, during repairs, it usually changes to a new one.

Old wallpaper should be removed from the walls before finishing, as well as cleaned and processed antiseptic compounds their surface.

Bathroom renovation. Preparing walls for finishing

The repair of the combined bathroom is carried out according to certain rules, since the air in such a room is very humid. In this case, the slats are installed only on the crate. In conventional toilets, the slats can be glued directly to the walls.

Frame installation

Since the walls and ceilings in the bathrooms modern apartments ideally smooth are rare, mounted plastic lining usually with pre-installation of the frame. The latter is easiest to make from wooden slats 40x25 mm. The elements of the crate are usually fastened horizontally. The frame is fixed directly to the wall with self-tapping screws with plastic dowels. The step between the slats is no more than 50 cm.

It is best to fix PVC lamellas when finishing the bathroom on a wooden frame

After the entire wall is upholstered, you can proceed with the installation corner elements, as well as the top and bottom plastic guides. They are fastened to the frame with brackets using a construction stapler.

When decorating walls with panels, corner elements are pre-installed

Panel mounting

To repair the bathroom, you can choose plastic panels of any color. But it's better small room light lamellas will look. There are actually many options for decorating a toilet with plastic. To see this, just look at the catalog of any online building store.

Design finishes such as PVC panels can have a very different

Actually, the decoration of the bathroom with plastic panels is done as follows:

• Previously, a spike is cut off at the first lamella.
• After that, it is inserted into the corner start element.
• On the reverse side, the first lamella will need to be fixed to each purlin on a clamp or bracket.

DIY bathroom renovation photo. PVC panels are fixed using a construction stapler

• The spike of the second panel is inserted into the groove of the first. To insert into the upper and lower guide, the element will have to be bent slightly. The second panel is attached to the crate in the same way as the first.
• All other lamellas are installed in exactly the same order.

Bathroom renovation. Photo of installation of PVC panels using the tenon-groove method

• The last panel is inserted into the finishing corner profile without additional fixation to the crate.
• Ceiling decoration is performed in exactly the same way.

Repair of a bathroom in Khrushchev. Photo of a plastic profile

Glue mounting

Do-it-yourself bathroom renovation in the event that the walls in it are even and it is not combined with a bathroom can be done using a simpler technology. In this case, PVC lamellas are attached directly to the surface of the room. liquid nails. The sequence of work in this case will be as follows:

• Repairs begin with cleaning the walls and ceiling from dirt. Next, the surfaces should be primed.

Photo of the finishing of the combined bathroom. Walls before painting PVC panels should be primed

• Large drops of liquid nails are applied to each panel pointwise in a checkerboard pattern with a step of about 30 cm.
• Next, the panel is firmly pressed against the surface and held in this position for several seconds.
• All other elements are attached in the same way.

Renovation in shared bathroom. Photo of a room finished with PVC panels

Of course, as in the first case, the finishing and starting corner profiles, as well as the upper and lower guides, are first glued to the wall.

Below we suggest you see how the bathroom is repaired with your own hands (video):

As you can see, using plastic panels, you can make a very high-quality and inexpensive repair of the bathroom.

Finishing the bathroom with ceramic tiles

Tiles - despite the fact that the price is higher - toilets are trimmed even more often than PVC panels. The bathtub, finished with modern design tiles, looks stylish and presentable.

In addition, it is much more difficult to damage a tile than plastic. The only drawback of ceramics can be considered only some difficulty in installation. Of course, you can repair the bathroom using tiles with your own hands. However, when performing this work, you should strictly adhere to all the required technologies.

Wall alignment

Repair of a combined bathroom in Khrushchev or a separate toilet usually begins with the alignment of all surfaces. It is better not to glue tiles on curved walls. Otherwise, the room will look messy.

When repairing the walls in the bathroom for tiling, they must first be carefully aligned

The alignment procedure includes the following steps:

• Peel off walls and ceiling old plaster. The tile that has served its purpose is removed from the floor.
• Continue repair by gluing (on gypsum mortar) plaster guides.

Alignment of the walls of the bathroom for tiling during repairs is carried out according to the lighthouses

• Once the gypsum has set, you can start applying new plaster. The solution is thrown between the beacons in large pieces, and then carefully leveled with a rule.
• The walls of the bathrooms in Khrushchev are leveled using the same technology.
• A screed is arranged on the floor along the lighthouses.

Floor repair begins with pouring the screed

Bathroom renovation in panel house can be made without preliminary leveling of surfaces. The walls in such buildings, unlike block and brick ones, are usually quite even.

Carrying out repairs in the apartment panel house, tiles can be installed without prior alignment of the walls

Installation of tiles

Tiles for a bathroom - especially a joint one - will only fit a special one, designed for use in conditions of high humidity. You can buy this variety in any hardware store. The tile is installed in the following order:

• At the first stage of repair, the walls and ceiling are carefully coated with a penetrating primer.

Walls for tiles are pre-marked without fail

• Next, the surface is marked according to the height of the tile.
• Installation of elements starts from the bottom.
• Glue is applied to the wall with a notched trowel or a special grater.

Photo of bathroom tiling. The adhesive under the tile is applied with a notched trowel

• A day after installation, the crosses are removed, and the seams are overwritten with a composition of a suitable color intended for this.

Bathroom tiles. Photo of the grouting process

Use of other materials

Tiles and plastic panels are the most popular species bathroom finishes. However, in some cases, repairs can be made using other materials.

Mosaic finish

Tiles during repairs can be replaced, for example, with mosaics. Finishing a bathroom with this material is not as difficult as it might seem at first glance. Smalt, ceramic and glass mosaics are sold not in small pieces, but in panels, approximately 30x30 cm in size. During production, the elements are glued face down on paper. After gluing the panel to the wall, it is simply wetted with water and removed after soaking.

Spectacular decoration of bathrooms with mosaics

Drywall finishing

This material for finishing bathrooms, both combined and separate, is also used quite often.

Installation of this type of finish is made either on wood, or - which is better - on metal carcass.

Drywall finishing is usually done through a metal frame

From above, decorative plaster is most often used to finish drywall in the bathroom. Finishing work with this material is carried out in stages:

• Previously, the surface of drywall is primed with a special tool.
• After the primer has dried, the plaster itself is applied to the walls and ceiling with a trowel in circular or direct hand movements. Its layer should be quite thin.
• After the first layer has dried, you can apply the second, and then the third. For structural plaster one or two will suffice. Textured is applied in 5-12 layers.

Photo of the combined bathrooms after repair. Finishing with decorative plaster

Wood paneling

Wooden panels in the bathroom are usually used only if it is not combined with the bathroom. Their installation is carried out using the same technology as the installation of plastic panels.

Sometimes bathrooms are finished using wooden panels.

As you can see, repairing a bathroom with your own hands is a rather troublesome task, but quite doable. Do the finishing slowly and carefully, and you will get a beautiful modern toilet with smooth walls and ceiling. If the paneling and tiling technology seemed too complicated for you, you can always hire specialists. Many companies today perform turnkey finishing of bathrooms and inexpensively.

It is not difficult to organize the decoration of the toilet with plastic panels with your own hands, if you have at least minimal experience installation work. But first, it is worth understanding the features of the material, the rules for installing the frame and other subtleties of the skin. But, following the advice of experts, everyone can independently repair the bathroom.

To decorate the toilet with panels with your own hands, it is enough to know the main technological points. To the special advantages of PVC panels can be attributed:

• convenient and simple installation, which everyone can handle;
• low price, in comparison with other types of cladding, plastic finishing is much cheaper;
• during repairs, alignment of the walls is not required, and this allows you to save money on building materials;
• plastic panels have good waterproofing, which means that you can not be afraid of moisture;
• easy to clean, it will be enough to wipe the panels with a damp cloth from time to time;
• long operational period.

It should be noted that in the event of a breakdown of one element, the structure can be easily dismantled. Thanks to these positive qualities, PVC panels are leaders among all facing materials.

But despite a large number of pluses, the material has a number negative qualities, which include the following:

• flammability: when ignited, the panels emit compounds harmful to the body;
• it is extremely difficult to work in small rooms, since there is no possibility to turn around;
• subjected to mechanical stress, even a slight blow can cause the bar to break or crack;
• hides a few centimeters of area, so that in small room their use is not recommended.

Plastic panels are very light, they are quick and easy to install. The material is used for finishing walls and ceilings, so they can be used to hide electrical cables, ventilation pipes and defects in the form of uneven walls, cracks.

Preparatory work

If the walls are even, then you can lay the material directly on the bearing surface. Although this option is extremely rare, therefore, most often most of the time is spent on installing the frame. Do-it-yourself plastic toilet decoration begins with the installation of the frame, for this you need:

1. First you need to remove old finish to a concrete or brick base. The tiled lining must be removed, if the tile is not removed, then over time it will fall off, but already under the new lining. If the walls are painted and the paint is holding firmly, then it does not need to be beaten off, it will not interfere.
2. Inspect the surface for cracks, if any, they must be embroidered, cleaned of debris, and then filled with a repair compound. Can be done with cement mortar Or use inexpensive tile adhesive.
3. To protect yourself from the appearance of bacteria or fungi under the panels, you need to treat the surface with any antiseptic. Experts recommend doing two impregnations with a time interval of 6 to 12 hours. During this period, the walls just have time to dry well.
4. If it is planned to lay sheets on the ceiling, then pre-stretch the wiring for lighting fixtures. The cable is placed in special protective casings that will protect the wire from moisture. Then they are fixed to the base ceiling with plastic clamps or using wire hangers.

After preparing the walls and ceilings, proceed to the manufacture of the frame. To do this, you can use metal or wooden profiles.

For rooms with high humidity it is best to use wooden bars that are pre-treated with an antiseptic. This option is much cheaper than a metal structure.

To mount the frame, you need to do the following:

• the bars on which the plastic panels will be fixed are treated with antiseptic impregnation, then they need to be dried and cut into the required sizes;
• now you should attach the bar to the surface of the wall, drill holes in it with a drill and put marks through them, and after that make sockets for fasteners with a puncher;
• since the plastic panels will be stacked vertically, then load-bearing structure must be mounted in a horizontal position, making a step of 50 centimeters;
• it is best to lay the crate at the height of the knee, belt and shoulder, in which case plastic sheets will not be damaged by awkward movement;
• plastic dowels are hammered into the nests made, then you need to attach them to them wooden bars and fix with locking screws, moreover, so that the hat is buried in the wood;
• now it is necessary to fix several thick boards on the wall, fix them with anchors;
• after that, you need to mark the exact location of the boards on the drawing, since later it will be possible to attach a mirror, bedside table or shelf to them;
• the ceiling frame is mounted according to the same scheme;
• to lay casings with electrical wiring in the bars, special grooves are cut out required size so that the cable is not pinched.

To disguise sewer pipes, you need to install vertical bar and fix it to the floor and ceiling with metal corner. After that, already mount the crate under the plastic panels. In order to have access to the pipeline, it is required to mount a wooden square at the very bottom, and already fix it on it inspection hatch. Installation metal profile is carried out according to the same scheme, but it is much more difficult to work with such material, so it is better for beginners to use wood.

Sheathing and finishing

After the frame is assembled, you can proceed directly to the skin. Since the area of ​​\u200b\u200bthe bathroom is usually small, installation will not take much time. To sheathe the structure, it is necessary to act according to the following scheme:

• placed on the corner start profile, and it must be aligned with building level and then fix with glue or self-tapping screws;
• attached around the perimeter ceiling profile, with the help of it vertical and horizontal elements will be connected;
• first wall panel it is necessary to cut in height, this gap will help ensure unhindered temperature deformation;
• now you can insert the element into the start profile and align it vertically;
• fix the sheet to the frame with self-tapping screws, and the upper edge is inserted into the plinth groove;
• the next sheet is inserted into the previous groove, the panels are assembled to the next corner;
• the last sheet is cut along, if the plastic is soft, then this can be done with a paint knife, if the material is hard, then you can use a file with small teeth, the panel is inserted into the starting profile;
• according to the same scheme, the entire space of the bathroom is sheathed.

At the very end, holes for built-in lights are cut out and installed decorative skirting boards, which mask the bottom edge of the panels. All gaps and cracks are sealed with moisture-resistant silicone. This completes the lining of the toilet with plastic panels. Self-assembly It's easy if you follow the sequence of steps.

Repair is a necessary thing, but not always pleasant. This is due to financial waste, physical effort and some other inconvenience. However, everyone will agree that the end result is worth it. In addition, the materials from which the repair is carried out play an important role. Today we will look at decorative trim toilet.

The place is small, but very necessary. It has its own characteristics, including high humidity inside. And this means that the finishing material must withstand such an environment. One of great options are plastic panels.

Why is this material special? What are its advantages and disadvantages? How is the toilet finished with plastic panels with your own hands? We will cover all this in this article. We will provide step by step instructions, and also see how the toilet is finished with plastic panels video tutorials.

Features of PVC products

What is good about this material? Let's start with the fact that among the many finishing materials plastic panels take their rightful place. And for the toilet they are just perfect. Why can you say so? The toilet has its own characteristics. That is why durable moisture-resistant materials are used for its decoration. Often tiles are bought for this purpose. But, its cost is much higher than the cost plastic products. The toilet itself is quite small, so working with tiles is inconvenient.

Another thing is plastic elements. With almost the same characteristics, they are much cheaper and easier to work with. Finishing the toilet with plastic panels can be done by hand. Here are other features of the material that are important to consider:

If we talk about the shortcomings, then they are the lack of strength of the panels, burning and their ability to fade. But, for the toilet, the second factor is not relevant, since usually there are either no windows in it at all, or they are made very small. So that Sun rays cannot damage the material. And with careful use, it will be difficult to damage the surface.

Options for finishing the toilet with plastic panels photo.

Immediately before finishing the walls, you need to purchase material. How to do it?

Choosing plastic panels for the toilet

So that the work was not done in vain, and the finish looked decent and was durable, it is important to choose the right materials. On the shelves of stores you can find a variety of products, but how to choose the right one? We immediately note that demand creates supply. And since the panels are popular, you can get to an unscrupulous manufacturer. Determining a defective product can be difficult. What will help in this? Let's look at a few tips.

Thanks to these tips, you can save yourself the opportunity to buy low-quality Construction Materials. The right choice of materials is already 50% of the work on high-quality finishing of the toilet. This is what the correct wall decoration in the toilet looks like with plastic panels in the photo.

Getting ready to install PVC panels

The first stage of work is preparation. If the panels have already been purchased, then it is time to take care of other tools and materials. The principle of mounting PVC panels resembles clapboard trim. Therefore, the work will require the creation of a frame. It can be metal or wood. We recommend that you refuse the wooden one, because the toilet is a wet room, the tree can rot and quickly fail.

To create a metal frame you will need:

In addition, the work can not do without such tools:

• screwdriver or drill driver;
• metal scissors;
• kleimers, self-tapping screws or a stapler for fixing panels to the frame;
• special profiles and skirting boards for plastic;
• tape measure, level, pencil;
• hacksaw for plastic;
• metal spatula;
• stationery knife.

When everything is assembled, you can begin to prepare the walls of the toilet.

Preparing the walls

Break, as they say, do not build. The first task is to remove the old finish from the walls. The good news is that the toilet is small, so it won't take much time. Using a spatula, you need to remove the old finish. The work is easy, but time consuming. Then the walls are cleaned of dust and dirt.

Note! So that nothing interferes with you during work, you should remove all unnecessary from the toilet.

When the surface is prepared, you can begin to create a frame or crate on the wall. The features and pluses of this finishing method are that in the space under the plates you can hide the wiring or insulate the toilet. Consider a step-by-step instruction for creating a metal frame.

We mount a metal frame

The main task is to make the frame even and correct, so you can not do without marking and controlling the process with a level. Since the panels will be mounted in a vertical position, the frame for them is made in a horizontal position. The creation instructions are as follows:

That's all, the frame for the walls is ready. Finishing the toilet with plastic panels (frame stage) do-it-yourself video.

Installation of plastic panels

Further work is to use plastic moldings. What are they needed for? PVC strips must be inserted into the appropriate grooves, this applies to the floor, ceiling and corners. For each case there is a molding. The photo shows exactly how to implement this in practice and what kind of molding is needed in this or that case.

That's it, the walls are ready. To make it easier for you, you can view the following information: wall decoration in the toilet with plastic panels video.

This is how the toilet decoration with plastic panels looks like photo.

Ceiling trim with plastic panels

If everything is clear with the walls, then the next step is the ceiling. It is recommended to trim it with panels too. It will look harmonious. Moreover, if you yourself learned how to decorate the walls with panels, then there will be no problems with the ceiling. Here the principle of work is the same. It all comes down to the following steps:

1. Marking on the wall.
2. Fixing the crate and other elements.
3. Installation of ceiling molding around the perimeter.
4. Installation of plastic panels.

As for the ceiling, there are some nuances here. For example, in the slats, you need to make appropriate holes for fixtures. For a toilet, it is better to use built-in Spotlights. To do this, markings are made in the appropriate place, and a hole is cut out in the panel using a special bit for a screwdriver. The work is easy. We have prepared visual video how to complete the work from start to finish (mounting on walls and ceilings). Let this apply to the bath, but the principle of operation does not change. Finishing the toilet with plastic panels video.

Conclusion

Now your toilet is ready for full functioning. Repairs in the toilet were made at minimal cost. As you can see, all the work is quite simple. If you try, then after 1-2 days the toilet will be ready. Plastic panels are an excellent material that is easy to work with, it will last a long time, and there will be no problems with its operation. The toilet will look like new. And due to the fact that the surface of the products is glossy, it will visually increase small space in room. With such work experience, you can successfully finish not only the toilet, but the apartment as a whole. Such skills will be useful in life.

Starting repairs in the apartment, the main emphasis is on the main rooms in the house, like the living room or bedroom. Repair of the toilet is often left for later, because a large number of requirements are not put forward to it. The environment here is not as aggressive as, for example, in the bathroom or kitchen. But there is one significant difficulty, namely a small space.

Most wall finishing materials significantly reduce space, and if, for example, this is acceptable in the case of a living room, then every centimeter counts in a cramped toilet. That is why the decoration of bathrooms and toilets with pvc panels is the most common option.

The video shows how simple finish pvc panels can transform the toilet room.

Advantages

• PVC panels can be fixed at a minimum distance from the wall. In total, after finishing the walls, the room will lose only 3-5 cm.
• Plastic is not afraid of wet cleaning and detergents.
• Plastic panels are much cheaper than most finishing materials.
• Huge variety of colors and patterns.
• Finishing the toilet with your own hands, even in the absence of special skills, will take only a few hours.
• To work with panels, it is not necessary to align the walls. They will hide all the bumps and mistakes of the builders.

Unfortunately, like any other material, PVC panels have a number of disadvantages that you also need to pay attention to when choosing a finish for a toilet.

Flaws

• Unlike wallpaper and painting, pvc panels will still take a few centimeters from the room.
• Although vinyl has a low flammability rate, it releases acrid toxic fumes when melted.
• pvc Low quality are easily damaged. And they need to be replaced.

As you can see, there are still fewer shortcomings. And positive traits are clearly winning. But in order to new renovation did not bring disappointment, you should know a few rules that should be followed when choosing pvc panels.

Selection Guide

At first glance, pvc panels differ only in pattern, but this is a misconception, the quality of plastic can vary significantly depending on the manufacturer.

It is best to ask your friends who have encountered this issue, since it is quite difficult to visually determine the quality. But there are some tips:

1. PVC panel should be soft. High-quality plastic can bend to an angle of more than 90 degrees. You can slightly bend the panel until tension is felt, the larger the angle, the better.
2. The mounting groove should bend freely without kinks, and return to its original position when it is released.
3. Panels should not emit obvious odors. A noticeable smell of plastic is a sign of poor-quality production.

The next nuance to consider is the width of the panel. It can be from 12 to 35 cm, the wider the segment, the more carefully it will be necessary to align the crate. The best option for walls, a width of less than 25 cm is considered.

Advice ! Panels with a width of more than 25 cm can be used on the ceiling. There, a slight distortion will not be so noticeable.

When these two factors are taken into account, you can proceed to the choice of color and pattern. It all comes down to personal preference and style. general interior apartments.

Preparing for panel installation

Finishing the toilet with pvc panels will not take much time, a more complex and responsible process is the manufacture of a crate, on which the panels will be attached.

If the walls are perfectly even, or they were plastered, then the panels can simply be glued to the wall without crates. This method will save space, but the surface will first have to be treated with a primer.

Any do-it-yourself repair must begin with the preparation of the tool, this will avoid unnecessary fuss, and save a lot of time. The list of everything you need is not so big, and there is nothing specific in it:

• Roulette.
• Building level.
• Pencil.
• Hacksaws for wood and plastic (suitable for metal, with a fine tooth).
• Perforator or drill with impact mode.
• A hammer.
• Construction stapler.

For the manufacture of crates, it is best to use wooden beam 1.5-2 cm thick, for pvc panels this is quite enough and it will not steal much space. Before you begin to fasten the timber, it must be treated with impregnations that will protect it from the formation of mold and fungus.

First of all, with the help of a puncher and dowels, the upper and lower strips are fixed. The lower one should be parallel to the floor and at a minimum distance from floor covering. The upper one is under the ceiling, but taking into account the future ceiling finish.

The remaining bars are also fastened horizontally at a distance of about 30 cm from each other.

Advice ! The smaller the distance between the planks of the crate, the stronger the panels will hold.

When all the bars of the crate are ready, you need to take care of the places where various accessories will be attached:

• Mirror.
• Hangers.
• Paper holders.

In these places, you need to install small bars, so that later, when drilling holes in the plastic, do not damage it.

When the wood work is completed, a decorative corner is installed in the left corner of the room, the installation of panels will begin from it. To install the corner, it is best to use construction stapler, but if it is not there, furniture nails will do. They are similar in size to shoe boots, but have a wider presser cap.

The corner is attached in 5-6 places at an equal distance, this is quite enough. If during the installation process, a slight curvature appears, then you should not pay attention to this, subsequently it will be straightened by the panel.

The most difficult stage of finishing the toilet with pvc panels is behind.

Panel mounting

Begin installation from the left side, inserting the panel with a comb into the corner. The first segment must be set according to the building level, then it will not be needed.

As soon as the panel is exposed, a stapler bracket or nail is driven into the groove tab. Fastenings are made in each bar along the entire height.

To clearly understand how the frame is made and the panels are installed, you can watch the video. For clarity, the master demonstrates the process on a simple wall, and every nuance is clearly visible.

Important ! When reaching the places where the bars for attaching accessories are located, they must be marked with a pencil so that later you do not look for this place through the installed panels.

Thus, fastening is carried out to the next corner. The edge panel is cut along the entire length and a corner is put on it before installation. It will be fixed to the next wall, from where the next segments will go.

Finishing in places of communications

The most difficult places for finishing work are communications. In order to close the pipes with pvc panels, you will have to make a wooden box, on which the panels will be attached. Sometimes such structures are intentionally made large sizes than required, then the decorative frame can also serve as an additional shelf.

Fastening the panels to the box is no different from wall decoration, the only difference is that the fasteners are not made in a special groove, but in the body of the panel itself, as close to the edge as possible, subsequently this place will be closed with decorative fittings.

Advice ! for finishing boxes, it is better to use outer corners, which are not put on the panel, but are attached to it with glue.

An important point when finishing communications is to remember the valves and meters that can be located in the toilet room. Access to such places should not be restricted, so you will either have to make small doors, which is not so easy, or leave these places open.

Ceiling finish

After the work with the walls is finished, you can move on to the ceiling. The principle here is the same, with the only difference that it is not necessary to install corners, their role will subsequently be performed by ceiling skirting boards.

Advice ! In order for the room to look symmetrical, you can calculate the distance so that the joint of the panels runs exactly in the middle. In this case, you will have to cut not one, but two extreme panels.

Finishing the ceiling, it is important to remember the lighting fixtures. Holes in the required places are best drilled on the floor, before the panel is fixed. And during installation, the wires are brought out into the holes.

All stages of work can be seen in the video

Conclusion

When the ceiling and walls are completely finished, it remains to do finishing touches, namely to fix the skirting boards. In stores you can find special plinths for pvc panels, they have a groove that is fixed on top of the panels, but to work with them, you will have to carefully calculate the height of each segment.

Therefore, more commonly used plastic skirting boards, which are simply planted on building glue. They are much easier to work with and do not require complex calculations and measurements of each panel.

Lastly, lighting fixtures are connected and on this the repair of the toilet can be considered complete.

As seen, modern finish toilet with pvc panels is a completely simple process that anyone can handle. To do this, you do not need to have building skills or experience, just buy everything you need and follow the instructions.

The toilet room, finished with tiles, looks very nice and respectable. But in order to lay it out beautifully, you need to have certain skills in working with such material, and the tile itself will cost a pretty penny. Perform high-quality repairs in the toilet without extra costs and on your own, you can use PVC panels instead of tiles.

Peculiarities

To finish the toilet with plastic panels, you do not need to have special building skills and physical strength. This material has a whole set of other qualities that provide ease of handling both during installation work and during the operation of finishing from it.

Although plastic panels are not without drawbacks.

• it lightweight material, which is simply cut and mounted. It can be used for both walls and ceilings. PVC panels will hide behind pipes and other communications that are present in the toilet and often do not look attractive at all, like "relatives" uneven walls. But it must be borne in mind that during installation on each side, such a coating “eats” about five centimeters of room space.
• It is convenient to deal with finishing the premises with this material alone, especially since it is very difficult for two builders to turn around in the cramped space of the toilet room.
• If the panels are installed correctly, they will last a very long time (up to twenty-five years), without requiring special care. They are impact resistant chemical substances, it is difficult to spoil the coating. It is enough to regularly wipe the PVC walls with a damp cloth so that the toilet does not lose its well-groomed appearance.
• The panels are resistant to moisture and temperature extremes.
• When making a choice in favor of decorating a toilet with such panels, it must be borne in mind that this is a material that melts under the influence of fire, releasing acrid smoke.
• If you hit the plastic wall hard, the panel may break.

Style and design

Thanks to this wide choice you can arrange a sanitary room in any style. With panels different color, colorful or with a pattern, a certain visual effect is achieved. So, if you use light panels, it will visually expand the space of the bathroom.

The use of panels with photo printing opens up unlimited scope for design. Entering the toilet, finished with such material, you can find yourself in the atmosphere of a paradise island, among waterfalls, mountains and in any environment that will contribute to peaceful loneliness. To create a complete picture, not only the walls, but also the floor and ceiling must be done in a single theme and color scheme. This rule works equally well both in the design of a separate toilet and a combined bathroom.

Although no one will forbid limiting yourself to the fact that the panel covers the wall only up to half or only a quarter, and the other part of the wall is decorated with washable wallpaper or painted with water-based paint of a suitable color.

Dimensions

Having made a choice in favor of plastic panels, you need to take into account that there is no single standard for the forms of their release. On sale you can find panels with a width of ten to thirty centimeters. Their length can be from two to six meters. The thickness is also different - from eight to twelve millimeters. If the choice is made in favor of sheet panels, then it should be borne in mind that their width is eighty centimeters and reaches two meters. Length from 105 to 405 centimeters.

When calculating the required amount of material, keep in mind that some of it will go to trim. Therefore, it is better to immediately purchase panels with a margin of fifteen percent.

Preparatory work

Before you get to the installation of the panels themselves, you will have to take measurements of the room and buy everything you need for repairs: not only panels, but also profiles for decorating exterior and internal corners, places where plastic adjoins the ceiling and floor, for decorating cabinets and doors provided for by your plan. You will need material to create a crate for future panels. You can choose wooden or metal slats. It should be borne in mind that how much the toilet area will decrease after all the work will depend on their parameters. The number of rails depends on the height and width of the walls, as well as the distance between the elements of the crate themselves. If a riser, pipes and a ceiling frame are hidden under the PVC panels, you need to lay the material consumption for this when calculating its total amount.

And you may also need dowels and screws. If they are not on the farm, you need to resolve the issue with their presence in advance. The plastic cladding technology also allows the panels to be glued directly to the walls, if they are absolutely even. With this approach to finishing, you will need "liquid nails". If the wooden crate will act as a support for the plastic, you need to purchase a processing tool wooden structure from decay. Using a primer for walls and ceilings will prevent mold from appearing under the panels. Insects under it also will not divorce.

To properly repair the toilet, you need to carefully prepare its walls for future decorative trim. Remove wallpaper and paint from them. To work, you need a metal spatula. Wallpaper that does not lag behind the wall can be soaked by rolling over it with a wet roller several times. Do not be too lazy to remove the old wallpaper to the end, so that later you do not have to dismantle the plastic panels and carry out repairs again if a fungus starts there.

As for the paint, it is enough to remove only what is already peeling off the wall. Sliced required amount elements wooden frame, they are treated with an antiseptic, including the places of cuts. Then they must be allowed to dry. AT apartment building for this suitable balcony. You can also take the workpieces to stairwell. Until the drying process is completed, you can process the walls and ceiling in the toilet itself.

The primer is applied with a long pile roller. A wide brush will also work. In uncomfortable areas - narrow. It makes sense to apply a couple of layers of soil, especially since it dries quickly. If you decide to repair the toilet in full - with the replacement of the toilet - it is better to remove the old one before you start the crate. If the pipes and old wiring require replacement, this issue should also be taken care of a little earlier than it comes to external design rooms.

frame

To make a frame for panel cladding yourself, you need to decide in advance how the PVC panels will be placed relative to the wall - vertically or horizontally. Placing the panels vertically will make the room appear taller, while placing it horizontally will visually expand it. Wherein " vertical version"Assumes the horizontal placement of the bars of the crate and vice versa. When installing rails, you need to focus on the readings of the building level. To fasten the bars to the walls, use self-tapping screws or dowels. Using self-tapping screws, you need to drill holes in the walls and insert plastic chopsticks into them.

By the time of work, the bars should dry well, otherwise they will lead later, which can ruin the whole thing. They are attached at a distance of about half a meter from each other. In places where cabinets and shelves will be placed, the crate elements must be placed “more often” so that the fastening is more reliable. The most common toilet finishing option is vertical way panel fixings. To make a frame for such a finish, you first need to install it side racks. To do this, the rails are fixed with self-tapping screws in the corners of the room. The vertical strips should not come into contact with the surface of the floor and ceiling.

Then the crate is done. The first bar is fixed at a distance of two centimeters from the floor. A rack line is created around the entire perimeter of the room. The same is mounted under the ceiling. In order for the crate to be uniform, after installing the upper and lower strips of slats, the distance between them is measured with a tape measure and divided in half. In the middle, another bar is strengthened. Each of the resulting sections is also divided into two and the bars are again strengthened at a measured distance. This continues until the distance between the elements of the crate is reduced to half a meter.

To build communication boxes for paneling, use the same materials as to create a frame on the walls. The boxes are attached to the floor and walls. You can connect the bars with self-tapping screws. In the process of work, it is necessary to provide places for technological holes that will provide access to hidden communications when dealing with household issues. As for the frame itself, not only wooden, but also metal guides can be used for its construction.

If it is supposed to finish the ceiling of the toilet with plastic, the frame on it is created in the same way as on the walls, only the bars are located more closely to each other.

sheathing

In order to make the walls of the room with PVC panels with your own hands, you will first have to install racks on which the decorative strips will be held. When the installation of the frame is completed, you can proceed to the next step, which involves the installation of racks that need to be nailed to the crate. The slats need to be cut at an angle of forty-five degrees. They can be attached to the crate with nails or a special stapler at a distance of thirty centimeters from each other.

Plastic panels have grooves and ridges, connecting them together, you can step by step finish the walls, giving them elegance. Decorative plastic elements in the corners and around the doorway will help close and hide the joints of the panels. It is better not to neglect the installation of such design components, otherwise the repair will look unfinished.

After installing the panels along the walls, you need to finish the box around with a decorative layer. vertical pipe that takes place in the toilet. To hide communications from the eyes, the panels will need to be cut to length, and in order to close uncomfortable place was aesthetic, in the end - install decorative corners where it's needed. To panel the ceiling of the bathroom, proceed in the same way as in the case of walls. But in the process of work, it will be necessary to make holes for future lamps and bring the electrical wires out.

In such an important place for an apartment as a toilet, it is not enough to carefully sheathe the walls and go around decorative panels all ledges, giving the room an elegant and well-groomed look. It is necessary to place hooks, niches and shelves in predetermined places so that the toilet is convenient to use. It is better to mark the places where all this will be attached along the course of the sheathing - then you won’t have to guess where the crate bars are placed.

Options for using panels to create hidden niches and shelves can be very different. A person who can manage furniture fittings, it will not be difficult to imperceptibly repair removable panel something that shouldn't be visible. It is possible, for example, to provide a window in the decorative casing, under which the water meter is located, with the ability to close it with a plastic door and easily open it only when required.

Finishing the bathroom with plastic panels usually takes no more than two days, and the results will please you for a long time.

Economy class repair with plastic decoration of the toilet room is good to use in Khrushchev. This is the easiest way to hide an old unattractive riser from view, to make the interior of a small room quite modern and cozy thanks to a competent choice of panels: with a pattern or plain. For example, red walls in the bathroom may seem too extravagant to some people. Green or blue tone in the company with a pattern, for example, in nautical style will certainly make the decoration comfortable and relaxing.

When repairing a combined bathroom, especially in an old panel house, you need to carefully consider the issue of ventilation, ensuring free air flow between the cladding and the wall, as well as the cladding and ceiling. Ventilation grill also need to be mounted from plastic, providing it with a decent design. When arranging the floor in the toilet, you can do cement screed and lay out the tiles. It is important that it does not contradict the overall color scheme of the updated interior. Even if you want to keep within the minimum amount of costs during repairs, you should carefully consider the choice of the decorative coating itself.

The risk of running into low-quality goods today is very high.

• To finish the bathroom, it is better to use panels with additives that increase their flexibility. Material without appropriate additives will be too brittle. It is not difficult to determine how high-quality a panel is in your hands. Plastic good quality can be bent into a ring.
• Press the edge of the product with two fingers. Reinforcement ribs located inside quality panel, cannot be deformed, and there are no dents on the outside.
• The joining strip of the lock on the edge should return to its original position when it is released after being bent. In a poor-quality product, this plastic strip may break.
• Through the top layer of the panel, its "insides" should not shine through.
• When choosing a material, use your sense of smell. If the panels are made from low-quality components, they will emit a chemical aroma that will only become stronger in the confined space of the bathroom. This is not only unpleasant, but also harmful to health.

• For PVC panels decent quality the composition should contain additives that do not allow the material to ignite. To verify this, ask for a product certificate from a specialist on the trading floor. If you are not provided with documents for the goods, it is better to go to another store.
• You should not stop your choice on panels of large width. When it comes to repairs in such a small room as a toilet, this is not profitable, since during installation there are too many scraps that you just have to throw away.
• Take the time to inspect each panel you purchase. It is not uncommon for sellers to put defective copies in a pack of goods. Exchanging them after purchase for a quality product can cost a lot of nerves. You will also have to prove that the panels were not damaged during transportation from the store to the house.

The "extra" time spent in the building materials store will be successfully compensated by the easy and quick installation panels in the toilet, as well as the pleasure with which you will be able to visit this secluded place for many years.

Beautiful examples

A variety of colors of plastic panels opens up great opportunities in order to embody the most interesting ideas design in accordance with the taste preferences of apartment owners.

Someone considers it worthy to decorate the walls of the toilet room under a stone, someone prefers certain wood patterns, and someone prefers abstract patterns that create a feeling of airiness and lightness, or floral ornaments present on the panels.

• Wall combination beige colour with an unusual pattern and a floor decorated in a red "outfit" will make the toilet room visually very warm. In the eyes of people who especially value warmth, this design will give the bathroom an additional appeal. Like the "neighborhood" of animals and trees on the walls.
• Connoisseurs of spring and summer will feel comfortable surrounded by walls with a pattern of branches and leaves. Even on a gloomy winter day, such an environment will return spring joy. A light green background helps to tune in to peace and never gets bored.
• The choice of flashy tones in the design of the toilet is a rather rare phenomenon, but there is no doubt that such a design can make an indelible impression on all visitors to a secluded room. No one will disregard the combination of red and black in a room "with a special purpose". Elements in the form of red prints on black walls will only enhance the effect, as will the boring lighting of the ceiling, echoing the design of the floor with white tiles.

• The design of the walls of the toilet under the stone would already look quite decent. However, in combination with a rich dark gray pattern at the bottom of the panels, this room looks especially presentable and rich.
• The use of black tones in the decoration of the bathroom only at first glance seems like a risky move. The combination of black walls with white fixtures creates a stylish contrast, making the interior impressive and modern. Energetic and strong-willed people clearly appreciate such a neighborhood.

• Gray panels for large tile give the room a detached neutrality and decent simplicity. Horizontally arranged narrow and light panels behind the toilet visually expand the cramped space. It no longer puts pressure psychologically on the person who is in it.
• Green plastic panels soft shade with a thin, graceful line of drawing along the perimeter of the toilet room, they look modest, but with dignity. Harmonious design indoors is created without original techniques, nevertheless it makes an excellent impression.

• If you use panels with vertical stripes in blue-pink tones on some walls of the bathroom, you can achieve a cozy effect, since such a pattern resembles the texture of a fabric. In this environment, you can feel like “under a flannel shirt”, or like “under a warm blanket”. If the same pattern is present on the floor, the effect will be even stronger.
• In fawn or beige shades of panels, the toilet space looks calm and lively at the same time, especially with the addition of a small floral pattern. Such colors and ornaments are chosen by balanced people who look at the world seriously and practically. If the walls, decorated with beige panels, are dirty, it will be noticeable, but it will not hurt the eyes. In addition, this surface is easy to clean.