In modern apartments and houses, the corners are often not straight, but rounded. This somewhat complicates the installation of the plinth. However, there are special technologies that can be used to bend both wooden and rigid plastic or even foam models.
In addition, a flexible floor or ceiling plinth made of soft plastic, polyurethane and even rubber is being sold today. If you don’t want to bother with bending the planks, you can purchase just such an option or order a radius one.
How to bend the floor plinth?
So, you do not want to use a flexible polyurethane floor skirting board or a model made of some other similar elastic material, but prefer to install a regular wooden or plastic one. The manufacture of a semicircular version for the floor in this case is usually entrusted to a specialist. However, you can try to round the desired bar yourself.
For installation on curved walls, rounded decor is used
How to round wood planks
In order to bend a wooden plank, it is pre-steamed. Water is poured into the basin and put on fire. The plank should warm up and steam over a jet of steam for half an hour. How to bend a wooden skirting board:
- You can round the bar by hanging it and securing some kind of load on both sides;
- Sometimes a special device is used:
You can round the element on a special device
- You can also attach two bars to the floor at a certain distance from each other and insert a plank of wood between them.
How to round a very hard wood skirting board? In this case, the bar, most likely, will have to be cut into several pieces, fixed to the wall and mounted transitions between them.
If it is not possible to bend the plinth, it must be cut into pieces
How to round a hard plastic model
Now let's see how to bend the plastic baseboard. You can round it according to the technology described above for wood. Sometimes they also use a slightly different method. At the same time, notches are made on the reverse side of the bar. Then it is heated with a building hair dryer.
Plastic models can be rounded in the same way as wooden ones.
Important: The heated bar must be rounded and immediately installed in place, without waiting for the material to cool. When doing this, be careful not to break it.How to bend a fillet for a ceiling
If you do not want to use a flexible ceiling plinth, you can try bending the foam or polystyrene foam.
Semicircular ceiling plinth also has to be used quite often
The foam baguette should not actually be bent, but rounded very carefully, squeezing in small sections. After the non-flexible, fragile fillet takes the desired shape, it is smeared with glue and pressed tightly against the wall surface, secured with small nails for reliability.
You can bend the foam model by gently crushing along the length
In order to make it clearer how to round the foam, we suggest you watch this video:
How to make the plinth a semicircle if the bending arc has too small a radius? At the same time, a foam fillet, like a wooden one, is cut into several pieces, which are mounted on a curved corner.
Pieces of foam fillet
Important: The joints between the pieces must be passed with putty or white silicone sealant. Next, the seams are carefully sanded. The resulting plinth radius can be painted with white or colored paint.Flexible floor and ceiling decor
Rounding the baseboard at home, without having some experience, is still quite difficult. It is easier to complement the floor finish using a bendable skirting board.
Flexible plinth floor or ceiling bend very easy
There are several varieties of them:
- Rubber. May have very bright colors;
- Cork flexible;
- Soft flexible PVC plinth. Perfect for a round wall. Sold wound on bobbins;
- Liquid tree. After some time after installation on a curved surface, it hardens, retaining the resulting shape.
- Flexible polyurethane skirting board. May have a variety of colors. A flexible polyurethane version for painting is also on sale.
Flexible polyurethane ceiling skirting is very easy to bend
How exactly to mount the plinth on a corner, if it is rounded, or on a column, of course, is up to you. If you are confident in your abilities, buy a regular hard decor and try to bend it. If you don’t have enough experience, get flexible skirting boards for the floor or ceiling.
Perfectly frame a rectangular room. But what if you have a non-standard room: with columns, semicircular walls, or a stretch ceiling of a complex configuration?
A flexible floor and ceiling plinth is suitable for you. With their help, you can hide minor flaws in the repair, uneven surfaces, as well as frame round structures.
You will learn about the varieties of flexible skirting boards, how to bend and fasten them from this article.
Flexible baguettes: their features
If the design of your apartment provides for semicircular or non-standard decor elements, you will need a flexible ceiling plinth. It will not only decorate the ceiling, but will perfectly decorate suspended round structures, hide defects and irregularities at the junction of the ceiling and walls.
Flexible skirting for the ceiling will emphasize all the advantages of the room
Sharp corners can cause anxiety and aggression. If you decide to create a calm atmosphere in the room, give the room softness - use a semicircular skirting board in its design.
Curved plank options
How to bend floor and ceiling moldings
Many people in the process of repair have a reasonable question: how to bend the plinth to give it the shape of a circle? Depending on the material the baguette is made of, it can be bent in several ways:
- making several cuts on the back side of the fillet. After that, they try to see if the baguette bends. If necessary, make additional incisions to bend the product;
- cutting into small pieces, and combining them on a semicircular profile;
- by heat treatment. The product is heated with a building hair dryer, bent, and then cooled in cold water to fix the bend;
- the formation of a semicircle by cutting off the stiffeners from the back of the product.
Semicircular plinth radius in the interior
Materials for the manufacture of flexible fillets
Most often used for framing ceilings. Flexible polyurethane skirting board can bend in any direction. The product can be tried on several times, decorated with semicircular elements - columns, arches, bay windows.
Plinth floor polyurethane flexible will beautifully decorate the ceilings in a semicircle
Remember: polyurethane products bend better than foam plastic products.How to round it so that it does not crack? To do this, it must first be steamed. After half an hour of being over hot steam, the wooden baguette will become malleable for transformation. When the product bends and takes the desired shape, it must be fixed until completely dry. This can be done by imposing a load, or by making a special form.
Rounding a plank of wood - bending along the radius
How to bend? By heating with a hair dryer or hot water, you can also bend a PVC baguette. Under the influence of temperatures above 80 degrees, it will become supple and soft, able to take any shape.
A curved PVC floor baguette is attached to glue or self-tapping screws in a circle, plastic components are installed at the corner and joints.
PVC product, an example of how to make a semicircle skirting board
Advice: when heating the fillet with a hairdryer, be careful not to overheat the product so that it does not deform.Special bending fillets for ceiling and floor
The simplest type of semicircular frame is a flexible PVC tape. It is self-adhesive and can be folded in half to form an even angle.
Tape products are available in different colors, this is the perfect skirting board for a round wall
If you are looking for a high quality, flexible skirting board, then composite wood-filled edging is a good solution. It is manufactured using the latest technology by injection molding and pressing.
Flexible plinth for wood-filled floor
An innovative product for decorating round elements is a flexible PVC floor skirting board. It is not exposed to ultraviolet radiation, moisture, solvents, does not burn and comes in different colors. These baguettes bend perfectly and therefore are suitable for columns, framing of semicircular podiums, bay windows.
Soft plastic baguette bends smoothly
To form a curved shape, the product is heated to 70 degrees, and then they begin to smoothly bend along the required radius. In case of hardening, it is heated in hot water and the semicircular edging is continued.
Non-standard design solutions will help to realize a flexible cork edging. Fastening to the walls is carried out with glue, which allows you to bend around even round columns.
Flexible floor plinth made of cork
Outcome
If there are columns, bay windows, semicircular ledges in the interior of the room, then you can use ready-made bending plinths to frame them, or bend the floor one yourself. A flexible frame will add style and softness to the room, make it more cozy, individual, and comfortable.
We bend the foam molding. Molding is an invoice convex plank with cross sections. It is used to decorate various surfaces: walls, ceilings, doors, fireplaces, arches, giving them a more expressive, complete and neat look.
How to bend the plinth to a semicircle?
Curly moldings imitating stucco molding and woodcarving become a real highlight of the interior. Moldings make furnishings more expressive and neat, and the interior itself - noble and harmonious. Share the video with your friends. program, connect and earn. on the channel in ReDECORation contact ======================================¬== Like it? Leave a LIKE and comment so that I know your opinion and can make the video even better. And don't forget to SUBSCRIBE to the channel to be the first to see new releases:
social comments Cackle
|
Those who have ever used skirting boards in the repair are well aware that they are connected at a right angle. Skirting boards are great at hiding some surface imperfections or just highlighting the interior, but right angles are sometimes a significant problem: if the room has decorative columns, custom-made stretch ceilings or rounded walls, then using such connections is at least unreasonable. Flexible plinths of two types (floor and ceiling) will come to the rescue, which can be bent, thereby repeating the curves of your interior. Their varieties, proper shaping and fastening will be discussed in this article. Peculiarities
If your ceiling has semicircular or round elements, as well as imperfections at the joints with the walls, then you need bendable ceiling skirting boards. They will help to beautifully emphasize the rounded structures on the ceiling and mask small defects. It has also been proven that sharp corners contribute to the emergence of aggression, therefore, in order to bring softness and comfort to the home, it is useful to use these skirting boards to create rounded joints. The atmosphere in this case will become calmer and more pleasant for perception. How to bend
It often happens that not following the instructions, people break the baseboard during the repair instead of bending it. It turns out this is due to the wrong way of bending. The correct method depends on the type of baguette (separate strips of skirting boards are called baguettes): The simplest are the first and fourth methods, since the rest require too much time and perseverance. Manufacturing materials
The first variety is polyurethane products, because they bend well, they can be reused and given almost any shape. In addition, they are more difficult to damage, which means that you can not be afraid to spoil such a plinth with inaccurate movements. Foam skirting boards bend well only to a certain shape, after which they crack. They are less durable and cannot be reused. An interesting solution is the use of wooden skirting boards. They can also bend, for this they are placed in hot steam, and after half an hour they are transformed into the desired shape. How to bend ceiling foam?To fix the effect of the plinth, they are fixed in the same position so that they do not deform. Plastic is also suitable for giving rounded shapes. With the help of a building hair dryer, it heats up to 70-90 degrees, after which it becomes soft and pliable, which means it can be given any shape. It is worth noting that it is undesirable to heat plastic skirting boards too much, because they can be deformed, and it is also worth protecting the skin surface from direct contact in order to avoid injury. Galteli
If you have no time or are too lazy to mess with skirting boards, then you can use PVC tape. It is flexible, easy to stick and hard to damage. The only drawback is that it requires careful gluing so that it does not fall off. There are floor and ceiling options. There are also other materials for the tape, which have greater strength, however, the method of bending and fastening them does not differ from conventional skirting boards. Fastening
Skirting boards are attached either with glue or with self-tapping screws, depending on the material of production. In the case of self-tapping screws, the more there are, the stronger the plinth will hold, but after installation it is recommended to mask them. The use of bendable skirting boards can solve two problems at once: emphasizing the circles of the decor and hiding minor flaws, the main thing is to carefully adjust the shape. |
|
Foam ceiling plinth: main characteristics and gluing technology
In this article, we will talk about how to properly cut, how to bend a foam ceiling plinth and how to install it. Until recently, there were no foam-based finishing materials that were light and comfortable to use. Therefore, most of the compatriots used paper panels to decorate the transitions of the walls to the ceiling, and only a few lucky ones could afford the use of gypsum stucco.
With the advent of baguettes made from extruded polystyrene foam, the situation has changed radically, as high-quality and aesthetically attractive ceiling design has become available to everyone.
Example of decorative design of the junction of walls and ceiling
Before you find out how do-it-yourself installation of polystyrene foam ceiling plinths is carried out, we will consider the main characteristics of this finishing material.
Main characteristics of extruded polystyrene baguette
In the photo, an assortment of foam baguettes
Expanded polystyrene ceiling plinths differ from similar products made from other materials in such qualities as:
- light weight and the ability to install on glue;
- ease of machining and, as a result, the possibility of cutting with a sharp knife and other equally accessible tools;
- smooth white surface of the product, no need for additional staining;
- low price in comparison with polyurethane analogues of skirting boards and gypsum stucco;
- a wide range of standard sizes;
- a wide range of textures.
When purchasing polystyrene foam ceiling plinths, you can choose products with both perfectly flat and embossed surfaces. Thus, you can choose a decorative material that will perfectly fit into both modern minimalist and classic interiors.
The abundance of standard sizes is another significant advantage characteristic of baguettes made of expanded polystyrene.
All these products can be divided into three categories:
- wide (thickness up to 20 cm) - an excellent choice for classically decorated interiors and for rooms with high ceilings;
- medium (thickness up to 10 cm) - a universal option that can be used for its intended purpose in any room;
- narrow (thickness less than 3 cm) the preferred choice for rooms with low ceilings.
The standard length of the foam ceiling plinth is 2 meters, which is very convenient when decorating rooms with not only a small, but also a large perimeter.
Important: In order to make the installation of baguettes easier and even a non-specialist could handle it, in addition to straight strips, corners for a polystyrene ceiling plinth are on sale.
The advantage in this case is that an inexperienced installer does not have to cut adjacent planks at an angle of 45 degrees, since everything is already ready.
As a result, the corner joint of the baguette will be accurate and reliable.
Now that we have learned the main characteristics and dimensions of the foam ceiling plinth, let's proceed to the installation work.
What you need to pay attention to when installing foam baguettes
Filling gaps with glue
How to install foam polystyrene baguettes with your own hands so that the result looks attractive and at the same time is durable?
The quality of the finished result in this case depends on factors such as:
- degree of preparation of mounting surfaces;
- correct selection of glue;
- compliance with the installation instructions.
During the gluing of baguettes, you need to understand that accurate installation will not work on curved walls and on a crooked ceiling, as small gaps will be noticeable.
Of course, these defects can be repaired, for example, with the same adhesive that will be used during installation. But the overall impression of carelessly done work will still remain.
The only effective solution in this situation is the preliminary preparation of mounting surfaces. Gluing baguettes is the final stage in the repair.
How to bend a ceiling plinth
That is, the plinth should be installed when the walls and ceiling are perfectly even.
Important: If skirting boards are installed before wallpapering or before walls are painted, the mounting surfaces must be primed.
In this way, you will ensure optimal adhesion of the finishing material to the plastered surfaces and, as a result, it will be possible to reduce the amount of adhesive used without compromising the quality of the installation.
Tubes with glue and mounting "guns"
The next item is the choice of glue.
Currently, the following types of adhesives are especially popular:
- adhesive "Titanium universal frost-resistant" - has a toxic odor, excessive fluidity and long setting times;
- glue "Baguette" - an environmentally friendly composition based on acrylic resins, it seizes for a long time, and therefore the baguettes need to be held for a long time so that they do not slip.
What can be concluded from the above? None of the popular adhesives is perfect. Therefore, if the installation of skirting boards is carried out at the junction of plastered walls and a plastered ceiling, we use Liquid Nails glue.
What is the advantage of such a solution?
- "Liquid nails" white. which means they will not stand out on the surface of the foam;
- the glue sets quickly and after a minute of waiting, the bar will not slide down;
- glue is durable. and you can be sure that the installed baguettes will not move away from the walls and from the ceiling;
- glue can fill the gaps between baguettes and curved walls;
- glue is sold in convenient tubes. which are inserted into the mounting "gun";
- the price of a tube of glue, as well as the cost of a "gun" is low.
So, we learned what kind of glue to use so that the styrofoam ceiling plinth is easy to install and the result is durable. Now let's find out what the installation instructions are.
The technology of gluing baguettes from expanded polystyrene
An example of how to bend a skirting board with cuts
As already mentioned, in addition to straight foam strips, additional elements are on sale - corners that can facilitate installation work. Unfortunately, corners can not be purchased at every building materials store, and therefore we will consider what is the instruction for gluing ordinary straight skirting boards without auxiliary corners.
Corner Formation Example
From the tool we need:
- miter box;
- a special hacksaw with a small tooth;
- sharp clerical knife;
- measuring instruments;
- mounting "gun" with a tube of glue;
- clean cloth dampened with water.
Scheme for trimming planks at the right angle
- we cut one bar from one end at the inner corner, as shown in the diagram;
- we apply glue with a dotted line on the upper and side back of the plank;
- we apply the bar, starting from the corner of the room, press it and hold it for 1-2 minutes;
Removing excess adhesive
- with a wet rag or finger, wipe the excess glue that protrudes along the edge line;
- from the straight end of the glued bar we measure the distance to the next corner, if the whole bar fits, we glue it, if not, then we cut it off;
- plinth trimming is done in accordance with the previously proposed scheme, namely, the plinth is inserted into the miter box, the desired angle is selected and a neat cut is made.
Important: Styrofoam ceiling plinths get dirty quickly, so if you don’t want to subsequently paint them, so as not to leave stains, work with clean cloth gloves.
Conclusion
We learned what a polystyrene foam baseboard is and how it is installed. The details can be found by looking at this article, after which you can leave your comments about what you read.
More information
More and more modern repair departs from the standards. The simple urban style is being replaced by more elegant and flexible design solutions. Straight lines are replaced by curvilinear, smooth, rounded shapes, so there is a need for new technologies for interior decoration.
Facing materials can be very different, but it is difficult to imagine a renovated space without skirting boards; this element of decoration is, without a doubt, indispensable in any interior. In the article we will tell you what a flexible floor and ceiling plinth is, and how to bend a plinth from different materials with your own hands.
Flexible ceiling plinth allows you to finish complex rounded shapes
Opportunities
It should be noted that the market of finishing materials quickly responds to the needs of modern repair. Now on sale are different models of bending skirting boards, and if the polystyrene strips are very fragile and almost do not bend, then the polyurethane profile with the addition of rubber is very flexible and plastic.
The best solution to finish a complex curvilinear area with many roundings are soft, flexible skirting boards. Usually it is a vinyl or flexible polyurethane baseboard with a high percentage of rubber. The profile is very flexible and is sold in rolls, it is easy for them to go around both the outer and inner radius corners.
For example, flexible floor skirting boards are used in rooms with complex shapes, for arches, columns, rounded podiums, etc., and flexible ceiling skirting boards are used to finish curved plasterboard structures or tension systems.
In addition to flexible models, a wide range of curved plinths with different diameters and from different materials is available for sale. As a rule, these are wooden and polyurethane segments for a round corner or column.
Flexible, semi-circular self-adhesive vinyl skirting board, easy to cut and bend to any radius
How to bend the plinth with your own hands
Despite the huge selection of soft, flexible and radius profiles, it is not always advisable to use them. As a rule, sometimes it is easier to bend a regular bending skirting board. Plastic, cork, MDF and wooden skirting boards can be easily bent into smooth semicircular curves.
But in order to bend them along the radius of a small circle, you should know the secrets of technology. Since the physical and chemical properties of materials vary significantly, hence the approach to the process of how to round the baseboard is very different.
Flexible polyurethane floor plinth allows you to easily go around semicircular surfaces with a gentle radius
So a flexible floor plinth made of composite plastic can be easily bent in a semicircle using a household hair dryer with a power of 1 kW or more. It is enough to heat the profile in the right place, and gently round it to fit the shape of a semicircular wall. It should be noted that the plastic bending composite plinth with wood-chip filling is difficult to distinguish from the veneered profile, so it is ideal for interiors with natural wood floors.
To bend a plastic plinth with a cable channel onto a flat semicircular surface, you will need to cut off all the stiffeners, leaving only the decorative layer intact. Further, in order for the molding to become flexible, it is heated with a building hair dryer, and gently bent at the installation site, during the process, grab the whip so that it “remembers” the required round shape.
Advice: In order not to damage the decorative coating, and not to spoil the structure of the plastic, do not bring the hair dryer close to the profile, do not hold it at one point, but drive it back and forth, at a distance of approximately 300 mm from the whip, so the heating will be uniform.
Cork flexible plinth floor can be easily bent, but small round shapes will have to be bent around with steam
If the profile is not flexible enough and it is required to go around semicircular shapes with wood, foam, MDF, and some polyurethane models, then in this case it is necessary to format the fillet. To do this, transverse cuts are made from the wrong side, almost in profile, leaving only the front layer of 3-5 mm intact. It is better to make cuts with a hacksaw for metal with a thick blade, every 5-7 mm.
Formatting flexible PVC profile
When profile formatting does not help, a radical method will have to be used to go around the surface. The non-flexible skirting board is cut into small pieces and each piece is individually fitted to the round wall. But this method of manufacturing a semicircular shape requires serious skills, so it is very difficult to install such a rounded segment on your own.
As a rule, the joining of several separate parts is used if the interior has a wide polystyrene ceiling plinth for a round wall. After finishing, the bent section is carefully puttied, and the plinth is painted in several layers, so the joints become invisible.
The photo shows how to finish a rounded surface with an inflexible whip.
How to make a curved segment from wood
Solid wood plinth is usually bent with steam. It is necessary to measure the round section, and cut the desired profile size with a margin of 50-75 mm on each side. Next, a large pot of water is placed on the stove, brought to a boil, when the steam becomes intense, a cut plinth is attached on top.
Depending on the type of wood, pine, for example, is more flexible, it takes 30-60 minutes to steam the profile, saying the words: “I’m twisting, I’m tormenting, I want to bend the profile!” When the profile is well saturated with steam, it is applied at the place of fixation, and bent along the desired radius. In order for the tree to take the desired shape, it should be fixed in several places. But this method can easily lead to deformation of the baseboard after drying.
Curved wooden profile in the interior
In order to properly bend a wooden whip in a semicircle, professionals make a special pattern, then make a template on it. The steamed whip is fixed on it with clamps, metal point and tape, so the bent semicircular shape is more even and accurate. Before making the plinth in a semicircle, it is recommended to impregnate the wrong side with PVA glue, so that after drying the bent segment better retains its semicircular shape.
We have also prepared a video for you on how to bend a plastic plinth with your own hands in a semicircle. We hope our advice will help you in the repair, remember, the key to a beautiful interior is accuracy and a creative approach to the process.
