The construction of houses from sip panels is a novelty in the domestic construction market. If a European has not been surprised by such houses for 50-60 years, then for Russian developers this technology is an occasion for heated discussions.

Sip panels are a structure made of a polystyrene foam layer, enclosed on both sides in OSB boards. The inner heat and sound insulating layer can be different thickness, it all depends on the future purpose of the panels. Thickened sip panels are bought for furnishing external walls winter buildings, and thinner panels are used for internal walls or for the arrangement of summer houses.

Advantages of the technology of building houses from sip panels

The main factor in the high popularity of this material for construction is the proper level of its factory readiness. That is, when buying sip panels, the developer buys a product assembled according to technology and ready for use. At the construction site, it remains only to correctly assemble the box of the house itself, which eliminates the marriage that occurs as a result of excessive "amateur" of the developer.

Advantages of sip panels

In addition, build with panels frame house the customer can do it himself, while saving quite an impressive amount.

Under the frame houses do not need a complex expensive foundation. Installation does not require a lot of manpower - everything can be done by hand, in addition, you do not need to spend money on ordering special equipment, the panels are easy to carry by yourself.

Although frame houses have a significant number of advantages, panels for them are still produced by more than one manufacturer, there are a huge number of them, and each makes panels according to own technology. So the assessment of the quality of the purchased material lies entirely with the buyer.

It is worth paying attention to the level of formaldehyde emission in the plates - it should be no more than E1 (this level is safe for humans). In addition, the inner layer of the board must be made of high quality self-extinguishing foam, polystyrene foam or polyurethane foam.

Despite the fact that the thermal protection of such houses is one of the advantages, it also has one significant drawback: the house functions like a thermos, because OSB boards, saving energy, do not allow water vapor to pass through. Therefore, frame houses need mechanical ventilation technology. Well suited for these purposes is a heat recovery unit that removes air from living rooms, and warming up cold air masses coming from the street.

pad ventilation system in such houses it is thought out even at the design stage, otherwise, elements of plates tightly fitted to each other will tightly clog the box of the house, creating unsuitable living conditions inside.

The technology of laying a ventilation system in a house from sip panels

In addition, houses made of sip panels have poor sound insulation. Styrofoam and expanded polystyrene inside the boards are not soundproofing materials on the contrary, they conduct well and sometimes amplify impact noise.

Of course, if your frame house stands in the wilderness, there is no need to worry about extra noise, but if the house is in a rather busy place, you will have to strengthen its interior decoration with noise-absorbing material with your own hands.

How to choose a foundation for a frame house?

Despite the fact that laying the foundation for a house from sip panels does not require high costs(about 20% of the total construction budget), you still have to make an effort and ingenuity. The thing is that the box of the house has an unusually low weight, plus, it is necessary to take into account the specific features of the soil, climate conditions, depth groundwater building site.

The main nuance associated with these houses is seasonal heaving of the soil, after which the entire box of the house can shift, crack or tilt. The best options for the foundation for them can be called:

1. Screw piles– simple, quick to install, cheap foundation. A screw pile is a steel tube to which a blade is attached, designed to be screwed into the soil. This foundation is good. load bearing capacity, because in the process of screwing the blade into the ground, it does not loosen it, but rather compacts it.
2. - rarely used technology. Unprofitable for developers, because it is suitable only for non-porous soils, while the rest will provoke its deformation after a season or two. To make such a foundation, it is necessary to remove 40 cm of soil, install a formwork with reinforcement and fill it with cement. The main disadvantage of such a foundation is the long drying of the concrete pour (up to a month). In addition, the underground of such a house will be ventilated much worse than in a pile house.
3. – a good option for slightly heaving soils. Its arrangement is a reinforced reinforced concrete thick slab lying on a bulk cushion. Such a foundation allows you to evenly distribute the load on the ground and protect the house from seasonal shifts.
4. - a good option for slightly heaving soil, much cheaper than a monolithic type. Such a foundation is a construction of separate slabs, located at the points of the corners of the future box of the house, at the junction of rooms and massive load-bearing beams.

How to do the installation of panels with your own hands?

Although the construction process frame house simple and fast to build it, you will need a lot of auxiliary tools, finishing materials and fasteners.

A careful calculation is made specifically in order to find out how much material will be spent on the construction. This calculation should take into account all the locations of door and window openings, their width and height, as well as the thickness of all external and internal walls of the house and the place where communication networks are laid.

Panel country houses - installation technology

Do-it-yourself installation of panel houses is carried out as follows:

• waterproofing (for example, roofing material) and a strapping beam impregnated with an antiseptic substance are laid on the existing base of the foundation;
• on the strapping beam, with the help of screws, the starting boards are attached;
• standard width of sip panels: 125, 250 and 280 cm. They are attached to each other using special grooves into which wooden dowels are inserted. Fastening should take place hopelessly, hermetically, with further blowing of the mounting foam, so that the future building does not let the cold through;
• if the house stands on a shallow foundation, the starting boards are attached to composite panels, not strapping.

Roof laying

Roof panel fastening scheme

Building a roof in a panel house is very easy to do with your own hands. In addition to the fact that in this case it is not necessary to make a crate, the roofing cake itself also does not need to be assembled, because the sandwich panel is a finished element.

You just need to lay the sip panels on the rafters, fix them with self-tapping screws, and, leaving a small ventilation gap, roofing. Best fit shingles and metal tiles.

In addition, if you have the means and can afford the services of a light crane, assemble the roof on the ground with your own hands, and then install it in place with a crane.

Exterior and interior decoration of the house with sip panels

Finishing, both internal and external, is done very quickly. Since the panels are smooth and even, the finishing cladding does not need to be pre-screeded and plastered.

However, prior to installing the drywall and finishing, the joints between the panels must be sanded and patched with paint mesh. In addition, before doing any Finishing work, it is necessary to make holes for communications.

In rooms with high humidity (bathroom, toilet), the joints are closed silicone sealant, and sip panels are overlapped in order to protect wall materials from getting wet. The floors in these rooms need to be additionally waterproofed or even laid with self-leveling acrylic floors.

Among the outdoor finishing methods, the most attractive are:

• thin plastic vinyl siding panels do not rot and perfectly protect from moisture;
• facade plaster- the most common finishing variation;
• corrugated board- light finishing material made of metal, characterized by its strength, resistance to rust;
• fiber cement is a strong, compressed slabs of cement (more than 90%) and cellulose.
• facade tiles- a cheap and popular material that imitates natural finishing elements.

Thus, having considered all the nuances and features of building houses from sip panels, we can conclude that positive characteristics material prevail over the negative.

In addition, the constant rise in the price of housing, especially apartments in cities, will soon make country frame houses the only way out for those who want to have personal real estate.

The construction of sip panels (SIP) can be attributed to the fastest, which currently exists in this market. In a week and a half it is quite possible to build one-storey cottage. The technology came to us from Canada. It is also extremely popular now in European countries.

Buildings made of sip panels are very warm and quite reliable. In our conditions, the material is ideal for construction country cottages and country houses. In this regard, many who want to become owners of such temporary or permanent housing are interested in how to build a house from sip panels with their own hands in record time due to technology.

What are sip panels

The sip panel is a three-layer building material. The inside is a thick layer of expanded polystyrene, which acts as an insulating and insulating material. On both sides, 2 layers of OSB chipboard are attached to it. It is made from wood chips, multidirectional and glued under pressure.

Expanded polystyrene provides excellent sound and heat insulation. OSB boards and high-quality glue, produced by special technology, securely fix insulating material. During construction, sip panels are connected to each other mounting foam, and wooden beams give rigidity to all structural nodes.

The advantages of this building material:

1. Durability - 100 years or more.
2. Rapid construction by docking SIP panels.
3. You can build in any season, since there are no mortars that require special conditions for solidification.
4. Very simple design roofs.
5. Due to the small thickness of the panels, the effective area inside the house.
6. A building built using this technology is very light and does not shrink.
7. Excellent thermal insulation, allowing you to save energy even during the heating season.
8. Ease of installation of doorways.
9. Ideally smooth and even surface of the panels allows you to use any finishing without pre-alignment of the walls.
10. Styrofoam and OSB board do not rot; they are not inhabited by rodents.
11. The material is absolutely clean and environmentally friendly.
12. The construction of it is quite simple and does not require the involvement of heavy construction equipment (cranes, etc.) in the process.
13. Low prices on SIP panels make the construction of them the most cost-effective option.

Flaws:

1. The panels do not allow water vapor to pass through, so buildings made of them need high-quality ventilation.
2. The material cannot boast of high fire resistance. In this regard, the issue of electrical wiring insulation should be given special attention. It is recommended to install a fire alarm.
3. The material is not resistant to moisture, so the foundation must be made wide enough to protect the structure from moisture.
4. The technology of building houses from sip panels does not allow much diversification of standard projects.

Construction of sip panels (video)

You should always start with design. And although great variety there is no need to wait in this matter, it is important to correctly calculate the size of the rooms, the placement of communications, etc. The complete assembly of the building is shown in the video.

The building made of sip panels is very light in weight and does not need a strong foundation. Under one or two-storey house you can build a tape or pile-screw. During the construction of the foundation, it is very important to equip its waterproofing with high quality. This will require bituminous mastic and 2 layers of roofing material, the sheets of which must be overlapped.

Then you can start laying the subfloor, which we also build from the same SIP panels (video). The photo shows how the floor is attached to the foundation. Between themselves, the panels are connected and immediately fixed with polyurethane sealant and self-tapping screws.

Building walls (video)

How the assembly of the building walls from SIP panels looks like can be seen in the video.

It is assembled literally like a big constructor. First, the bottom trim is mounted. As is the case with many modern building materials, building with sip panels starts from the corners of the house. To the corner panels, butt-to-butt, the subsequent ones are attached in both directions, up to the next corners. Between the panels is laid wooden beam fixed with sealant and self-tapping screws.

To build any building, you must use the building level. AT this case this is also true, despite the fact that the sip panels are perfectly even. Using the level will help to avoid deviation of the walls from the ideal vertical. The ends of the walls and the upper selections are covered with sealant, after which we begin to make the upper trim.

To create floors between floors, all the same sip panels are used. They have sufficient strength for this and can withstand a very solid weight (furniture, the residents themselves, etc.). After installing the floors, we continue to build walls - now the second floor. The ceilings are reinforced with wooden beams.

Door / window openings are made very simply: they can simply be cut with a regular hacksaw. The material is perfectly processed and requires almost no effort during this process. All this can be done by hand.

How to build a roof

The technology of erecting a roof on such a building is extremely simple. To build it, we again use the same SIP panels. Plates are mounted on the same principle as walls and interfloor ceilings. Rafters are not required. How is the connection of roofing and wall panels, shown in diagrams 1 and 2.

Please note that a support column is installed in the center. To do this, you can use a bar 50x70 mm. All mount roofing elements made using self-tapping screws, sealant and docking bars. When the roof is assembled, you can immediately proceed to top coat. You can cover the roof with almost any material (metal tiles, corrugated board, soft tiles etc.). The choice of material depends on the preferences and material capabilities of the homeowner.

Finishing

Outside, the building can be lined plastic clapboard, siding and any similar material that will protect the walls from moisture. Interior decoration is even more simple. Since the walls of sip panels are absolutely flat, there is no need to mount any leveling frame.

The walls inside the building can be wallpapered, plastered, even tiled or mosaiced (bathroom, kitchen, etc.). Flooring also suitable for almost any. You can lay laminate, linoleum on the floor, floorboard and even parquet, if there is such a desire. Even including all the finishing work, the construction of a 3-4-room mansion from sip panels in the worst weather can take a maximum of a month and a half.

The technology is simple and low-cost; the cost of all materials is also minimal. Everything is done simply and very quickly. If you need the most inexpensive country house with excellent heat and sound insulation, the construction of sip panels is just right. In the next video, we posted a review of the owner of such a house. It will help to better understand what such a structure is like.

More recently, it has become very popular to build houses with a wooden frame. Now there is a constant search for new and improvement of existing technologies of frame construction. The article will describe the stages of building a frame house for a relatively new technology from sip panels.

What is a sip panel - manufacturing process

Sip panel or, as it is also called, sandwich panel - multifunctional construction material. You can use it in almost any environment. The cost of the panels is small, and the potential for their application is practically unlimited.

Wall sandwich panels are a three-layer material. Let's see how they are made.

How is the process of manufacturing sip panels - step by step diagram

Step 1: Selection of materials

For the outer layers, durable material is used: fibreboard, oriented strand board, wooden planks, magnesite plates, galvanized steel. Plate thickness 9 or 12 mm.

For sip panels, it is better to exclude the use of wood, as it is highly flammable, short-lived, and also the most time-consuming to process. Most often, for the construction of houses, OSB boards are used in SIP panels. The recommended thickness is 12 mm. For load-bearing structures they can be adapted for use in high humidity.

OSB is made from wood shavings, the diameter of which does not exceed 0.6 mm. The length, as a rule, is not more than 140 mm. Such chips are laid perpendicular to each other in three layers. An adhesive waterproof resin is added during the manufacturing process. Further from high pressure and temperature, this material is pressed. The result is a plate with increased strength and at the same time high elasticity. The outer layer of OSB boards is also waterproof. With the help of wood tools, the slabs are very easy to saw. OSB holds the fasteners through the way the wood chips are laid, and therefore differs significantly from other similar materials where the resin provides retention of the fasteners.

The insulation is placed between two rigid protective layers material. For this layer, expanded polystyrene, polyurethane foam, or mineral wool are used. The last two heaters are non-combustible. When choosing a brand of foam, you need to pay attention to its flammability and flame decay time. The thickness of the material, depending on the thermophysical properties of the frame house, can vary from 50 to 250 mm. If more preference is given to mineral wool, then a parabarrier film must be laid between it and the inner slab.

When used in SIP panels mineral wool a material is used that has a density of 100–120 kg / m³. Such a product does not burn and cannot spread fire. When heated, the bonding elements can release unpleasant odors, but nevertheless such thermal insulation material Much more environmentally friendly than Styrofoam. But mineral wool increases the weight of the sandwich panel. When compared with polystyrene foam, the weight will be 2 times more. Therefore, this type of insulation is rarely used in sip panels. The high cost also negatively affects the choice of this material. The use of mineral wool as a heater in a house made of sandwich panels can cost 1.5–2 times more.

For mass production in sip panels, polystyrene foam with a density of 25 kg / m³ (PSB-S-25 or PSB-25) is used. Due to its lightness and low cost, this insulation is very popular. It is 98% made up of carbon dioxide. Due to this, it has a low thermal conductivity and, accordingly, high thermal insulation properties.

Such material has a sufficiently high strength, resistant to fungus and moisture. But in polystyrene foam, mice like to gnaw out nests in which they then settle. The purpose of this material is primarily external insulation walls. The thickness of the insulation depends on what kind of house will be built. For permanent residence the heat insulator should be no thinner than 50 mm. For building summer cottage a maximum of 20 mm of such insulation is sufficient. We should not forget that polystyrene foam burns, melts from exposure to open fire and emits acrid black smoke. The fire safety of the structure is partially ensured by the fact that the foam in the SIP panels is covered with OSB boards.

Step 2: Selecting the Right Adhesive

To connect all layers of a sandwich panel, the adhesive must retain its qualities all the time while the house is standing. Therefore, such material must withstand different humidity, temperature change and other unfavourable conditions. The toxicity of the adhesive after polymerization must be completely eliminated. When assembling sip panels in Canada, the USA and the EU, the following brands have proven themselves with the best side: Macroplast UR 7229, Macroplast UR 7228 and Kleiberit 502.8.

Step 3: Production of sip panels

The OSB board must be evenly coated with glue over the entire plane. Then you need to lay a sheet of expanded polystyrene on top of the plate. Then you need to reapply polymer composition and cover with a second OSB board.

Glue must be applied within no more than 10 minutes. When this material is exposed to air for more than the specified time, polymerization begins. The glue foams up a lot and expands in volume. In this case, it is necessary to carry out pressing with pressing of the elements to be glued within 18 tons. This is done with a powerful press. Glued wall sandwich panels must be cured for 2–3 hours. The glue dries completely in 15-30 hours. After that, the protruding edges of the insulation must be cut off.

What will be the foundation?

Prefabricated houses sip panels have enough a light weight, so a reinforced foundation is not needed. For such structures, it is advisable to use a shallow foundation. In addition to this option, a pile, columnar or slab type of frame house foundation is also used in construction practice. For example, pile foundation can be done in any season of the year, in any weather. It can be installed in as soon as possible, large financial costs are not required. There is no need to carry out painstaking earthworks.

For a frame house where wall panels are used, we recommend using one of the most popular and classic options supports - strip foundation. To do this, you will need to mark the construction site. Then dig a trench 50–60 cm deep. The width can be made 40–50 cm. In the next step, you will need to make a sand and gravel pillow of 20 cm, which must be tamped down.

Then you can proceed to the installation of formwork. Boards 10-15 cm wide are suitable for this. As an alternative, moisture-resistant plywood is allowed. Be sure to make the formwork 50 cm above the soil level.

Next bind reinforcing cage. For this, rods 10-15 mm in diameter are most often used. After that, a concrete solution is prepared. A concrete mixer will significantly speed up this process. It is necessary to regularly ram the solution poured into the formwork using a vibrator. This event will remove air bubbles from concrete mix, why the created foundation will be stronger. When all the pouring work has been done, the concrete solution must be allowed to brew and gain strength. Experts recommend that the foundation stand for 3-4 weeks before the walls are erected.

Installation of the frame and floor - what you need to know

This process begins with attaching a strapping frame wooden belt to the foundation. The cross section for such a beam is most often used 250x150 mm. In the corners wall boards are connected to each other with the help of the grooves made. Anchors, as a rule, are used 10–12 mm in diameter, and their length should be 35 cm. They are required to be installed at a distance of 1.5–2 m from each other. In the corners, it is better to use two anchors. Bolt heads must be recessed.

Wall building tricks

Wall elements are installed after fixing the guide boards on the strapping beam. Their size depends on the thickness of the wall panel. It is necessary to lay such boards taking into account the indentation from the edge of the timber by 10-12 mm. Be sure to observe a strict horizontal. In order to make their fasteners, you will need 70x5 mm self-tapping screws. It is better to make indents between them 35–40 cm.

In the corners there are two wall frame panels are installed by dressing them on guide boards. The grooves must first be foamed. Using a level, you need to align vertically and horizontally. After that, it is necessary to fasten the sandwich panels with self-tapping screws to the guide boards. Mounting step required to be done in 150 mm. The panels also need to be fastened together. To do this, you need boards with a cross section of 50–200 mm. They are installed between two panels. To make a reliable fixation, self-tapping screws 12x200 mm are required.

How are panel-frame buildings heated?

Assembly of vulture houses

Buy a house from SIP panels

Building houses from sip panels with your own hands, on your own, video, instructions, step by step guide

Step-by-step video instruction - how to build a house from a sandwich - SIP panels yourself

How is the assembly of sip at home. Video

Each instruction is very detailed guide, study everything carefully, carefully, pay attention to all the nuances and details !!! Be sure to read and study both documents, as this is the only way you will get a complete understanding of the entire construction process yourself! Remember that SIP at home is just one option among types of prefabricated buildings.

In the documents, you will learn EVERYTHING about how to make a panel-frame building with your own hands, what materials are used for this, what you need to know, and, of course, you will find and get acquainted with practical skills in the construction of prefabricated buildings.

Stages of building a frame house from SIP panels - a step-by-step sequence of actions

Any erection of a panel-frame structure is step by step process, which assumes the sequence construction works. When we build a house from sip panels with our own hands, we have to not only pour the foundation ourselves, but also insert windows, doors, and also carry out interior wall decoration, conduct electrical networks and communication, without forgetting attic floor construction and facade decoration.

Construction - manufacturing, pouring the foundation

Foundation construction - This is the foundation of your future home. The most common options for foundations are tape shallowly recessed and foundation on screw piles. It's no secret to anyone that prefabricated houses have relatively big weight, good environmental friendliness and do not require massive foundations.

Foundation on screw piles with strapping for vulture houses. A photo

The foundation of screw piles with their own hands, on their own. Video

This significantly reduces construction costs and increases its speed. Through this link you can learn in detail about all types of foundations for houses from SIP panels.

The planning and choice of the foundation of the house will depend on the type of soil, the slope on your land plot, as well as directly from the area of ​​the building itself. If the foundation is monolithic concrete. Then you definitely need to make a waterproofing layer. Details are at the link above. It happens that if the soil is loose, sandy, then it makes sense to use a monolithic slab as a foundation.

Foundation for sip house - monolithic slab. A photo

Strapping beam - subfloor

The next stage in the construction of a sip house with your own hands is the arrangement of the base of the floor and walls of the first floor. If the building has two floors. As a rule, a dry strapping beam is used for this, which is pre-treated with antiseptic compounds - this significantly improves fire safety.

Laying the strapping beam on the foundation. A photo

Laying is carried out along the perimeter of the house and along the contours of the bearing internal partitions. If the foundation is on screw piles, then you should first equip the base from a steel channel.

Installation of SIP panels - assembly of a house kit

So you bought SIP panels and your next action is to install them yourself. Assembling a house from SIP panels is a process that requires special attention! If you are a beginner, then it is best for you to install the walls of the house according to the instructions that you can download at the beginning of the article. It should be understood that making a house kit happens individually for each project.

Assembling a house from sip panels on your own, on your own. Video

Preparing a set of houses from sip panels for assembly. A photo

When the house kit was delivered to you, you need to pay attention to the assembly sequence. All panels must be numbered, and the numbering must clearly correspond to the assembly scheme of the house kit. Your task is to lay out all SIP panels according to the numbering along the perimeter of the foundation. If the building consists of two floors, then the set of the first floor is laid out first.

Do-it-yourself installation of sip panels. Video

SIP panels have a fairly large weight, which provides good sound insulation. You will definitely need help, at least two people, be sure to take care of it. The panels are mounted by splicing them together, as well as tying the lower base to the strapping beam.

Do-it-yourself SIP panel installation. Photo courtesy of idealfoundations.com.au

The connecting element between the SIP panels is the frame elements - this is a wooden antiseptic beam. Also, to enhance the fastening properties, mounting sealant is used - this is a one-component material based on polyurethane foam, in the common people mounting foam.

This connection scheme is called "thorn-groove", it is reliable enough to provide a long service life of prefabricated buildings. After connecting the panels with a wooden beam, it is necessary to screw in self-tapping screws on both sides, which greatly enhances the rigidity of the entire structure.

Installation of wall panels occurs only when the lower trim is completely done. First, the corner components of the house kit are installed, and only then the rest of the supporting racks and the panels themselves are attached (installation is carried out from the first corner panel and simultaneously performed immediately in both directions, to the second corner sandwich panel).

Proper installation of a set of houses from sip panels. Video

After installation, each panel must be adjusted using building level. This approach allows you to correctly expose all the walls of the kit in space on your own. During the detected deviation and adjustment - the key to the correct installation.

Assembling the walls of the house from SIP panels. A photo

Strictly adhere to the scheme for assembling SIP panels and carefully monitor the sequence of actions. Remember that all joints and gaps between SIP panels must be treated with mounting foam!

Assembly, installation, installation of ceilings

There are the following types of floors- zero overlap, interfloor overlap and attic flooring.

Zero overlap of sip panels. Photo from stavimsteni.ru

You can organize any of these floors, both from SIP panels, and using wooden frame from tee or two tee beams. Just like it is pros and cons of sip panels, and there are advantages and disadvantages for each type of overlap.

Interfloor ceiling made of sip panels. Photo from sipdom.ucoz.ru

If you decide to assemble floors from sandwich panels, then this is done by analogy with assembling walls. This is a completely acceptable approach, since the heat-insulating properties justify the laboriousness of the process. Of the minuses, if the area of ​​\u200b\u200bthe house is large. You may need heavy equipment.

Assembling the frame floor of the house in the vulture house. A photo

The assembly of ceilings using T-beams or two T-beams (depending on the bearing loads) is reliable, inexpensive and efficient. This approach is also justified from the point of view of laying engineering networks - ventilation,sewerage systems, water supply and heating system.

Upper timber trim

The upper strapping around the perimeter of the sip at home is required. It serves to securely fix the entire structure and increase the overall seismic resistance of the building. The strapping wooden beam, which is laid on top, is also at the same time the basis for overlapping, either inter-storey or under-roofing.

Upper wall cladding made of SIP panels. A photo

Construction of the roof of a SIP house - do-it-yourself roof

Arrangement and construction of the roof is the final stage of installation of a set of SIP panels. Your further actions will depend on what type of roof is included in the house kit.

do-it-yourself roofing of a house from sip panels. Photo from achfoam.com

In most cases, the roof is built directly from SIP panels. With this approach, the organization of the rafter-transom system is not required. The performance of sandwich panels is quite enough to withstand all load-bearing loads with a margin. The roof of SIP panels is assembled on the same principle as wall panels, according to the drawing of the house kit.

You will also be interested in: Back to the main SIP Electricity in SIP houses Finishing in houses from SIP panels Pros and cons of building from SIP Fire safety Service life of SIP houses Heating in houses from SIP panels Go to the main site

For more detailed advice on your question, please send us a message.