How to water a tree so that it dries quickly: effective methods and useful tips. How to destroy a tree without cutting it down What to pour under a tree to make it dry

Each gardener plans the placement of trees and shrubs on his site to create a beautiful landscape and comfort. Naturally, in the process, the thought does not come to mind at all that it will be necessary to destroy the landings. Unfortunately, this happens quite often. If a tree becomes ill or has grown so much that it poses a threat to the lives of people or the integrity of buildings, it must be eliminated.

Just cutting the trunk is not always possible. In this case, special chemical substances. They need to water the tree so that it dries out, and it is easier to cut it into pieces and remove it from the site. From this article you will learn what substances can be used for these purposes.

How to make a tree wither

There are many ways to artificially dry a tree, both scientifically based and folk. Chemical agents are considered more effective, which, although they pose a certain danger to the soil and humans, still allow you to quickly dry even a large specimen.

There are several ways to destroy garden trees:

Watering the leaves and bark with a solution chemicals;
Application of special preparations on sheet plates;
Inoculations of poisonous substances that quickly penetrate the juices of the plant and destroy it;
Placing the poison in the soil near the roots of the plant.

From the point of view of technology, the tree does not need to be destroyed: it is enough just to cut it down, and treat the remaining stump with chemicals for destruction. However, if you need to act quickly, the advantage is still given to chemical preparations.

But, after the tree has dried up, it needs to be recycled. How to do it right - the author of the video tells.

Destroying a tree with chemicals is not difficult, especially since most of them are available to every gardener (Figure 1).

The most effective means include:

Sodium nitrate: most often used to destroy stumps, but it can also be used to affect adult specimens. In order for it to dry out in a year, you need to drill a hole in the trunk and introduce a chemical there. If this is not possible, you can simply pour the soil around the plant with a solution of saltpeter, but in this case, the drying process will take several years.
Ammonium nitrate: applies on the same principle as sodium, but certain differences between these substances still exist. Ammonium nitrate is produced on the basis of urea, which accelerates the decomposition of wood, so it is most often used to treat stumps and open root systems.
Picloram: another effective tool that directly affects root system. The substance inhibits the roots and the culture gradually dries up.

Figure 1. Main chemicals for tree destruction: sodium nitrate, ammonium nitrate, Picloram

In addition, conventional herbicides can be used to destroy plantings, as well as special preparations, arboricides, which are designed specifically for the treatment of trees and large shrubs. We will consider the features of the effects of these substances in more detail.

Arboricides

In fact, arboricides belong to the group of herbicides, as they are designed to control vegetation. The only difference is that arboricides are used exclusively for the destruction of trees and shrubs (Figure 2).

The substance must be diluted with water and spray the culture with a ready-made solution. The procedure is better in early spring so that the substance does not accidentally get on other plants. However, if the need for treatment arose in the middle of the season, it is better to use another method: drill a hollow in the trunk and place the preparation there. In this case, the aboricide will only affect the selected crop. At the same time, it is advisable not to plant and harvest at this place during the year.

Figure 2. Technology of the impact of arboricides on plants and types of preparations

One of the best means for thinning plantings, preparations Arsenal and Arbonal are considered. Their composition is designed in such a way that the substances act directly on the wood, quickly destroying it, and the culture dies within a short time.

herbicides

Herbicides that are used to control weeds in a vegetable garden are often used to kill trees as well. These drugs include Roundup and Tornado. They have enough high efficiency, and if you pour the soil around the plant with a solution of the chemical, it will quickly dry out.

When using such powerful herbicides, it should be borne in mind that they not only contribute to the drying out of trees and shrubs, but also affect the soil as a whole. Therefore, after processing, other crops cannot be planted in the selected area during the year.

Leaf processing

There are quite a few ways to destroy a tree, and one of the most popular is the treatment of leaves with special chemicals.

Note: Since leaves play an important role in the growth and development of any crop, the application of chemicals will cause the crop to stop receiving nutrients and gradually die.

This method is not suitable for processing large specimens, but it can be used when destroying low plants or shrubs. The selected specimen is simply sprayed with a solution of the drug, and it is better to do this after watering or rain. In dry weather or with a lack of moisture, the effectiveness of the drugs is reduced.

As a rule, powerful herbicides are used for such processing, and it is better to apply them either in early spring or late summer. This will protect the rest of the plants in the garden from exposure to chemicals.

How to water the bark so that the tree withers

bark processing chemicals- another simple but enough effective way destruction of landings. Herbicides diluted in water are also used for this purpose. Instructions for use of the working solution, as a rule, are indicated on the packaging of the drug.

To carry out such processing, you need to make a mark on the trunk at a height of 30-35 cm from the ground level (Figure 3). The herbicide solution must be mixed with any oil to increase viscosity. Next, the mixture is applied to the bark with a brush, and this must be done until the liquid stops being absorbed. This means that the substance has penetrated inside and begun to act.

Figure 3. Chemical destruction of a tree through the bark

The drying process using this method will take some time, depending on the age and strength of the tree. But its main advantage is that such processing can be carried out for any crops, regardless of their type, height and age.

How to remove tree roots and stump

A fairly common situation is when the trunk is already cut down, but the stump and roots remain in the ground. You can also uproot them in the usual way, using a crowbar or a shovel, but this procedure will require a lot of time and effort from you.

It is much more effective to use chemicals to remove stumps and roots:

On the initial stage you need to cut the trunk, as the cut must be fresh. If the stump has been in your area for a long time, simply freshen up the cut slightly by sawing off some of the top layer of wood from the stump.
Prepare a herbicide working solution by mixing it with water and a small amount of oil.
Treat the stump with the resulting solution. If it is large, it will be enough to apply the agent only on its outer edge (about 5-10 cm) and part of the cadmium (internal tissues). On sections of small diameter (no more than 10 cm), the composition is applied completely to the entire surface.

Figure 4. Removing the stump and roots

Roots simply need to be watered with a solution of herbicide. Such treatment will further weaken the root system and wood residues, and the stump can be easily removed (Figure 4).

Safety measures when destroying trees

The use of any chemicals requires compliance with safety rules and personal protection. First of all, it should be borne in mind that the solutions used to destroy plantings can adversely affect the condition of other plants in the garden, so care should be taken during the application process so that the solution does not get on neighboring crops.

In addition, it should be borne in mind that some old specimens can grow together with roots, and careless processing can destroy not one, but several plants at once. Unfortunately, it is almost impossible to predict such a development of events. It should also be borne in mind that some herbicides have a negative effect on soil fertility, so when choosing a product, you need to carefully study its composition and effect on the soil.

One should not lose sight of the fact that when working with herbicides, one should wear a protective suit, goggles and gloves so that the toxic agent does not get on the skin or mucous membranes.

The video shows the technology and stages of chemical destruction of the stump.

Wood is a beautiful element landscape design and an important part of the development of all life on our planet. Therefore, sometimes it is very difficult to make a decision on its removal, but if it has already been made, let's figure out how to get rid of the trees on the site in the best possible way.

If you decide to resort to using chemicals to dry the tree, then you should choose the best tool for this. Most often, chemicals have their effect on the root system of the plant. Before you water the root of a tree so that it dries out, you need to know the composition of the soil under it. Sometimes, instead of roots, chemicals are applied to the bark of a tree or its living tissues.

If possible, you can cut down the trunk of the tree, and then use chemicals to destroy the stump. This way you can get rid of unwanted trees on your site even faster. Let's look at what chemicals can be used to dry a tree:

Sometimes it is applied directly to the soil or to a tree trunk. More quick effect can be obtained by introducing saltpeter into the hollow of a tree: in a year the tree will dry up and can be burned. Watering the soil will give an effect only after a few years.
Ammonium nitrate is similar in its action to sodium, but it also has a difference. Such urea-based saltpeter accelerates the process of decomposition of wood, and then the roots of the tree turn into fertilizer. In this case, the trunk with the signs of drying that have appeared can be uprooted, and the opened roots can be poured again with a solution of ammonium nitrate.
Herbicides "Roundup" or "Tornado" are most often used to destroy unwanted trees. These funds are used in the deconstruction of low-value young plantings, and also, if necessary, to remove the stand in coniferous plantings. Preparations "Arsenal" and "Arbonal" have high ability penetration into wood, they are used for thinning large areas of forest, as well as in nurseries and other agricultural plantations.
"Pikloram" is effective both when watering the soil and when spraying the tree itself. This drug acts depressingly on the root system, which leads to the drying of the entire plant.

Using the method of chemical exposure, it must be remembered that several factors are taken into account when implementing it. important features.

The tree has the ability to protect damaged areas, that is, "cork" them. This means that around tissues exposed to herbicides, protective layer, which will worsen the degree of absorption of the drug and reduce its effectiveness. So if you want to remove a tree by applying a chemical to its living tissue, do it right after the nicks. As a result, the chemical preparation is absorbed as quickly and fully as possible.
In some cases, trees belonging to the same species and growing next to each other grow roots together. Accordingly, if you apply the herbicide to one of them, the second will also receive its dose of the drug and will either be damaged or destroyed.
There is a danger that the removed tree will release the herbicide into the environment, and the rest of the plants will absorb it.
To improve the accuracy of exposure, dyes are often added to the preparation. Thus, it is possible to control which tree has already been processed and which one is yet to be destroyed.

In addition, it should be understood that the removal of trees is possible in other ways, without resorting to chemical preparations. This includes felling a whole tree, and sawing it in parts, and work on an aerial platform. In more detail about the variety of methods for removing green spaces, you will be told in any organization professionally engaged in arboristry.

What should be considered when using chemicals?

The use of chemicals inevitably requires compliance with safety precautions, as well as rules for use. One of the main problems with this approach to the destruction of woody vegetation is the detrimental effect on the soil. Specialized drugs, as a rule, are free from side effects in the form of a deterioration in soil fertility, but this aspect should still be taken into account when choosing which solution to water the tree so that it dries along with the roots.

Purposeful treatment of one tree, even under the maximum conditions for limiting the action of the drug, can lead to the death of other plants. This is due to the fact that trees can grow together with roots, forming a single vascular network. Thus, if one specimen is poisoned, then the “related” tree will soon die. It is almost impossible to calculate such a probability, especially if a dense landing prevails on the site. You can insure yourself only by careful choice: how to water the tree so that it dries out without affecting other plants. In this regard, it is important to take into account that trees of not only one variety, but also of a genus, are subject to fusion.

It should be remembered that when using chemicals to destroy trees, the person conducting the work is responsible for the effect produced.
Trees are able to “cork” damaged areas and naturally protect themselves. "Corking" is that the tree is able to form a protective layer around damaged tissue. This layer can reduce the absorption of herbicides and reduce the effectiveness of the drug.
It should be remembered that trees can have one common vascular system, as a result of root fusion. As a rule, the fusion of roots occurs in trees of the same species, but it happens that the roots grow together in trees of the same genus.

Thus, a herbicide can be carried from one tree that threatens another tree that should not be eradicated by damaging or destroying it.

It is important to remember that once the herbicide has been released from the tree, it can be taken up by other plants. Serious consequences can be that the destroyed tree releases a substance into the environment, which is absorbed by nearby plants and can damage them.
It should be remembered that the addition of dyes to the herbicide increases the accuracy of processing. Trees processed this way are easier to track and are less likely to be missed or re-processed.
It should be remembered that herbicide application instructions often warn against spreading directly under the bark of a tree. But the roots of a tree often grow outside the area directly under the crown of the tree.

You can use the rule of thumb that on the east side, the roots of the tree extend to a distance equal to the height of the crown of the tree, and on the western side, to half this distance.

mir-ogorodnikov.ru

How to water the tree so that it dries out?

Gardeners competently approach the choice of seedlings and try to plan the planting of plants as accurately as possible in order to get the maximum benefit from them. Taking into account the characteristics of the soil, lighting, climatic conditions. However, in some cases, the owner has a question: “How to water the tree so that it dries out?”. Oh sure, this method can not be called humane, but in certain situations there is no other way out. So, for example, if the tree is old, the diameter of the trunk is more than thirty centimeters, but it is impossible to cut it down, since there are other plants or buildings nearby. In this case, there is only one thing left - to dry it with the help of special chemicals.

Please note that almost all chemicals primarily affect the root system. When choosing this tool, it is necessary to take into account the composition of the soil. There are also those drugs that affect the living tissues of the tree or the bark. AT ideal it is best to cut down the tree, and then process its stump. Thanks to this, the process of getting rid of the tree will be as fast as possible.

So, we present you a list of the best tools:

Saltpeter sodium. In most cases, it is applied to stumps. However, it must be applied both to the soil on which the plant grows and to its trunk. For a quick result, it is recommended to introduce the mixture into the hollow, as this will allow you to get a quick result. The tree will dry out in about one year, after which, if necessary, it can be burned. If you water the soil with saltpeter, then this will bring results in a few years.
Ammonium nitrate. It is very similar to sodium nitrate, but these substances have differences. Such a substance is made on the basis of a substance dangerous for the plant - urea, which several times accelerates the process of wood decomposition. Thanks to this, their roots quickly turn into ordinary fertilizer. The trunk, on which obvious signs of drying have appeared, is recommended to be uprooted. The same roots that open, re-treat with the chemical.
Tornado or Roundup. These herbicides are most commonly used to kill unwanted trees. They are an excellent tool for the destruction of both coniferous and tree plantings.
Arbonal and Arsenal. These preparations penetrate well into the wood, due to which they are recommended for thinning the forest. However, they are also used in agricultural plantations and nurseries.
"Pikloram". An excellent tool for the destruction of trees, which is applied by watering the soil or spraying the plant. The tool depresses the root system, as a result of which the tree dies.

And finally, remember that a tree is a living organism and it must be destroyed in extreme cases. Do not get carried away with this procedure.

ladym.ru

Quite a lot of people are faced with the fact that a tree grows near their house that interferes (blocks the passage, obscures the windows of the apartment, etc.), however, the owner of the territory where this tree is located refuses to issue a logging ticket for any reason. There is a way out in this situation: it is necessary to quietly dry the tree on the vine, and then cut it down as dry.

If you are determined to destroy the tree, then I suggest that you read the instructions.

1. So, first of all, prepare a drill with a drill with a diameter of 5 to 10 mm, then drill several holes four to five centimeters deep in the tree trunk. Drill at an angle of approximately 45-50 degrees to the ground. The height of the holes to be drilled does not matter.

2. Take a regular pharmacy syringe, draw the drug into it with active substance glyphosate (you can use any drugs, some of the most common are Tornado, Halidor, Ground) and pour it into the previously made holes. It is worth noting that it is necessary to use a drug with a concentration of the active substance of at least 200 grams per liter (the concentration is indicated on the product label). For example, to destroy a tree with a diameter of 30-35 centimeters, only 30-40 ml of the drug with a concentration of 360 g / l is enough.

3. In order to hide the traces of the injections, just carefully cover each hole in the tree with earth, brush off the chips and make sure that the drug does not leak out, as it is clearly visible on the bark, and it dries for quite a long time. After the work done, the tree will soon begin to dry out.

It is worth noting that it is possible to freeze a tree with other herbicides, however, preparations with glyphosates, although they act much more slowly, however, after the roots die off, these preparations are immediately inactivated by soil microflora, which cannot be said about heavier herbicides with the active ingredients imazapyr and sulfometuron-methyl, which, after the death of a tree will certainly fall into the soil, which can lead to the death of other closely growing plants.

Sources:

how to kill a neighbor tree

How to dry a tree on the vine unnoticed

www.kakprosto.ru

How to destroy a tree without cutting it down

What to do if the tree has grown so much that it begins to interfere with the foundation of the house, electrical wires as well as other plants? Is it possible to kill it without cutting it down, quickly and reliably?

If a neighbor tree interferes

We will not give you advice on how to destroy an interfering neighbor tree, for this there is a law that does not allow planting large trees closer than 3-4 meters from the boundaries of the site. If you're having this problem, you might want to seek legal advice and talk to your neighbors in the language of law and order.

They themselves must remove the neighbor's tree so as not to conflict with the law and those with whom they have to live side by side. But each person has the right to dispose of the trees growing on his own plot.

How to kill a disturbing tree easily and quickly?

Experienced gardeners it is recommended to drill in the trunk oblique hole so long that it reaches the core of the trunk, and pour liquid into it, which will begin to destroy the tree from the inside. It can be a strong acid - acetic, hydrochloric, formic. The acid kills the tree within a week.

Ask railroad workers for a solution of dichlorophenoxyacetic acid, which they use to control shrubs and vegetation along the railroad tracks. This tool is also injected into a hole drilled with an inclination.

You can pour gasoline, diesel fuel, acetone into the hole - the effect will be the same. Do not forget about herbicides - they destroy not only weeds, but also quite large trees. These are herbicides with glyphosphate Tornado, Arsenal and other products with a similar composition.

Herbicides are used in the same way as acids, after pouring in the killing liquid, the hole is closed with clay, putty, garden pitch so that the liquid does not evaporate.

To kill a tree, you can spray its leaves with Roundup, diluted in water in a strong concentration. First, the agent destroys the leaves, then it dries up on its own, deprived of the possibility of photosynthesis and the production of the necessary nutrients. Roundup can also be injected into the trunk of a tree, just as described above.

In addition, herbicides are applied directly to the bark in the lower part of the trunk - at a distance of 30-50 cm from the ground. This procedure is carried out from spring to early autumn. So that the herbicide does not drain from the bark, it is mixed with oil and smeared with it on the bark.

There are special herbicides for the destruction big trees and shrub arboricides, buy and apply them according to the instructions.

It is believed that a copper nail driven into it can easily and quickly kill a tree, perhaps a big tree It will not work to destroy with one nail, several nails will be needed.

A small tree can be destroyed by burying a few old batteries next to it, but their acid is harmful and dangerous to all living things.

An interfering tree can be killed without cutting it down, with the help of salt - it is injected in a solution with water - by watering the tree, or simply by burying it under the roots. It is advisable to add salt under the central root, but it is also acceptable to add brine under the peripheral processes. At the same time, keep in mind that the roots of the tree grow unevenly - on the eastern side they stretch to a distance equal to the height of the crown, and on the western side - to half the height.

Using this feature of the root system, some gardeners try to destroy a neighbor's tree without penetrating someone else's site. They just bury salt at the fence next to the tree and that's it. At the same time, no efflorescence occurs on the soil, and it can be very difficult to prove their malicious intent. The salt method works for 1-2 months - first the tree sheds its leaves and then dries up.

But, we should not forget that salt in the soil will negatively affect other plants, as well as water in a well or well. Water and soil are also polluted by other means applied directly under the roots - herbicides, gasoline, diesel fuel, acids. Therefore, it is necessary to act with them thoughtfully and carefully.

There is an ecological method of "killing" a tree. Reliable, but not very fast kills him decorative liana with characteristic name- woodcutter. This flowering liana braids the tree trunk, is attached to it not with suction cups and not with antennae, like other vines, but with sharp spikes. As a result, the tree dies, and now it is important not to let it go to other, necessary and useful trees. The tree pliers are used if it is not the tree itself that interferes, but its roots.

Sometimes homeowners have a problem, which is the need to destroy a growing tree in the wrong place. The article will discuss how to do this without cutting, quickly and imperceptibly.

Destruction by watering the soil with chemicals

You can quickly destroy a tree without resorting to cutting down with the help of herbicides. The following drugs are considered the most effective here:

Zencor;
Meister;
Prometrin.

The process itself looks like this:

Pre-soil around the tree must be well moistened. On dry soil, the substance will penetrate to the roots for a very long time.
Thoroughly water the soil around the trunk with a solution of herbicide.

Attention! When working with herbicidal substances, you must strictly adhere to the instructions and follow the safety rules. Otherwise, you can harm your health.

The described method has a significant drawback - vegetation growing nearby may suffer. To avoid this, it will be necessary to build a plastic or metal chemical processing zone that goes into the depths of the fence.

To destroy a tree, instead of herbicides, you can use kerosene or diesel fuel. Within a month, flammable substances should be added little by little until the branches begin to dry out. You can learn more about the methods in the attached video.

How to bring a tree to death with injections

To destroy a tree in a similar way, you will need the following tools and devices:

Drill with a suitable drill 5-10 mm in diameter.
Ordinary medical syringe.

Attention! Most effective application This method is achieved by introducing the drug into the circumference of the trunk every 5-10 cm.

Direct injections are carried out as follows:

At a height of at least 1 m from the ground, holes 5-6 cm deep are drilled with a drill. In this case, it must be taken into account that each of them should be located at an angle of 50 ° relative to the ground.
Using a medical syringe, the drug is poured into the holes. To prevent leakage of liquid, each hole should be covered with earth. Soon the plant will begin to noticeably dry out.

Drugs that are suitable for the technique:

ground;
Tornado.

When performing, it should be borne in mind that the concentration of the toxic substance glyphosate in the selected product must be at least 200 mg. This method is suitable for destroying a tree whose trunk diameter is more than 5 cm.

Attention! If you take heavier herbicides, their main substances can penetrate the soil and kill neighboring plants.

Applying funds to wood

An effective method for removing unwanted vegetation is to apply appropriate preparations to the bark. By suitable means for this option are:

Glyphos;
Roundup;
Tornado;
Arsenal.

Advice. The technique is best suited in case of need for selective removal of a large number trees.

Depending on the thickness of the bark the tree has, poisonous substance applied in different ways:

directly on the surface of the cortex;
through the incisions made.

The first is suitable if the tree is young, with thin bark. In this case, the drug is applied to the surface of the trunk at a level of half a meter from the ground. Lubrication is continued until the liquid is completely absorbed.

Advice. Before processing a tree, it is better to mix the poisonous substance with oil. This will speed up its absorption.

In the presence of a thick bark, the first option will not work. This is where the cuts will need to be made. As a tool, it is better to use an ax. With its help, deep notches are made around the trunk. Cut down areas are abundantly watered with herbicide. Be sure to consider that the procedure will work quickly in cool, dry weather. Precipitation able to wash away the poisonous liquid and all work will go down the drain.

How to remove the root after drying

After the tree has dried up and been cut down, it remains on the surface, and the roots are in the ground, which presents certain inconveniences to the owners of the site. Two methods are used to quickly remove stumps:

applying funds to the cut itself;
lubrication of notches.

A 10% solution of butyl ether works very well for this job. If you want to remove several stumps, then in this case, use saltpeter. The procedure is carried out like this:

Holes are drilled in the remains of the tree.
Fill them with saltpeter.
All holes are closed with stoppers.

In this form, the tree is left until the next season. During this time, it will dry thoroughly, after which it will be much easier to remove the stump and roots.

Removing an adult tree is a complex and time-consuming process. However, with the help of the above methods, it can be greatly simplified.

How to get rid of a tree: video

Gardeners often approach the choice of seedlings very responsibly, striving to plan the planting with maximum accuracy in order to get the maximum benefit from the plants. They take into account not only the climatic conditions in their region, but also the lighting and soil features. However, sometimes owners suburban areas interested in how to water the tree so that it dries quickly. This method, of course, can hardly be considered humane, but sometimes there is simply no other way out.

For example, if there is an old tree with a trunk diameter of more than 30 cm on the site, but it cannot be cut, because there are other structures or plants nearby. The only way out in this situation is to dry the tree using special chemicals.

How to water a tree so that it dries quickly

Chemical methods for eliminating trees

There are many ways to ensure that the tree on the site quickly withered. However, the most common of them are those that involve the use of chem. preparations intended for the destruction of plants. And no matter how harmful these remedies can be, they nevertheless allow you to perform this work as quickly as possible.

Chemical ways to destroy trees

More specifically, there are such chemical methods tree destruction:

watering plant tissues with chemical compounds;
covering the leaves with special preparations;
grafts that kill trees;
placing the drug in the ground next to the trunk;
complete destruction (including the stump);
applying a chemical agent to the bark.

Important information! Note that most of the chemicals described below affect the root system of trees. When choosing a specific composition in without fail take into account the composition of the soil. There are drugs that affect the bark or living tissues of plants.

Ideally, the tree should be cut down altogether, and the remaining stump properly treated. So you can get rid of the tree as quickly as possible. Be that as it may, to begin with, let's get acquainted with the most effective means and features of their application.

Popular Tree Killing Chemicals

If you intend to use chemicals, you must choose the most suitable option. Below is a list of the most effective (according to summer residents) chemicals.

Processes occurring with herbicides

Note! A tree is still a living organism, which must be killed only in extreme cases. Do not get carried away with this procedure too much.

Now, having familiarized ourselves with the main chemicals that can quickly dry a tree, we will consider which processing methods are most popular. Some of these methods involve the use of certain drugs described above.

When working with chemicals, do not forget about personal protective equipment!

The main ways to destroy trees with chemicals

Immediately make a reservation that there are many such methods, so we will consider only the most effective of them.

Method number 1. Applying chemicals to living tissue

The bark of the tree is an obstacle due to which herbicides cannot penetrate into the vascular tissues of the plant. Therefore, in order for the remedy to reach its destination, make downward cuts on the surface of the trunk, but do not tear off the bark. Use a small ax for this. As a result, notches and cuts should be around the entire circumference of the trunk.

Application of drugs to living tissues of a tree

The herbicide you have chosen, use the cut after making the cuts - apply it to the tissue of the tree.

Making cuts on a small tree

Note! Do not use herbicides in spring time because the juice that will ooze from the incisions will prevent the chemical from being absorbed.

Method number 2. Watering the soil with herbicides

Separate preparations can be used for uniform application to the soil surface. After rain or artificial irrigation, the herbicide will enter the root system. To concentrate the chemical in one place, you can resort to the installation of barriers in the ground (for example, concrete).

Note! This method is advisable to use in cases where it is required to destroy several or many trees at the same time.

The soil around the tree can be watered with herbicide

Method number 3. "Killer" injections

They are very similar in principle to method No. 1, and differ only in that special devices are used to introduce chemicals into tissues. The maximum efficiency of the methods is achieved if a point action is taken along the circumference of the trunk in increments of 5-10 cm. Injections are made at a height of about 1 m from the ground. The method is used for trees whose trunk diameter exceeds 5 cm.

Step 1. First, prepare a drill, as well as a drill for it, the diameter of which is 5-10 mm.

Step 2 Make holes 4-5 cm deep as described above. It is important that the drill is at an angle of 45-50 ° relative to the ground during operation.

Holes in the trunk

Step 3 Take a simple pharmacy syringe, fill it with a product whose active ingredient is glyphosate (for example, "Ground", "Tornado", etc.), or, alternatively, pour the chemical directly into the holes. The concentration of glyphosate in the product must be at least 200 g/L.

Take a regular syringe

Herbicide "Ground"

For example: to dry a tree with a trunk diameter of 35 cm, you need 35-40 ml of a product in which the concentration of glyphosate is 360 g / l.

Step 4 Seal the holes with earth to hide the injection marks, remove the chips and see if the drug flows out (the latter is good because it dries for a long time and is clearly visible on the bark). Soon enough, the plant will begin to dry out.

There are special devices for stem injections

Note! You can use other herbicides, but it is still better to give preference to preparations with glyphosate, because they are immediately inactivated by soil microflora after the root system dies off.

Heavier herbicides based on sulfometuron-methyl or imazapyr, on the contrary, penetrate the soil after the death of the trees and often kill nearby plants. Although you can take care of the barriers described earlier.

Method number 4. Treatment of leaves with preparations

This method is very popular when destroying shrubs, the height of which does not exceed 4 m. It can be used from the beginning of spring to the end of summer (more exact time depends on the particular herbicide). The effectiveness of drugs is markedly reduced if the weather is dry and hot, and the tree suffers from a moisture deficiency.

If the preparations are applied to the leaves of crops with a large annual growth, this can lead to the appearance of excessive shoots (except for some extremely susceptible species). If you use this method, then it is not necessary to impregnate the barrel with chemicals.

Growth on a tree

Method number 5. Simultaneous destruction of the trunk and stump

Here, first, the tree itself is removed with an ax or a chainsaw, and then a chemical is produced. stump removal (more on this at the end of the article). If using this method, apply the herbicide only to the fresh stump. If the trunk diameter is large, process only the outer edge of the stump (no more than 5-10 cm), including the cambium - the internal tissues of such trees are mostly already dead.

Complete destruction of the tree along with the stump

If the trunk diameter is large, process only the outer edge of the stump

If the trunk diameter is less than 10 cm, apply the chemical to the entire cut surface. Apply the drug immediately after you cut the tree - so the effectiveness will be maximum.

If the trunk diameter is less than 10 cm, apply the chemical to the entire surface of the cut

Method number 6. Tree bark processing

Measure 30-35 cm from the ground, make a mark on the trunk and treat the area below this mark with a chemical preparation. It is advisable to hold the event in the spring or summer. Before applying, mix the product with oil, then process the bark until it is completely saturated. Tellingly, this method is applicable to all trees, regardless of what type they belong to and what sizes they have.

Treatment of tree bark with herbicides

Greenhouse in autumn: cleaning, fertilizing, general care

Greenhouse cleaning work begins with cleaning debris and washing the structure. And the first stages are carried out even before the start of frost. Read more about this in this article.

Below are helpful tips, which will help you with the destruction of the unwanted tree.

The person who destroys trees with chemicals is solely responsible for the final effect.
Remember that the accuracy of processing can be improved by adding a coloring agent to the herbicide. Trees are much easier to track after this treatment, so you are unlikely to miss them when reprocessing(if required).
Trees can "cork" cuts and damage, thereby protecting themselves. In other words, a protective layer is formed around the damaged tissues, which can reduce the effectiveness of the drug used. For this reason, when using Method #1, the chemical must be applied immediately after the incisions have been made.
Cuts seem to heal
The herbicide released from the tree can be absorbed by neighboring plants. This should not be forgotten either.
Some trees may have one vascular system (this is a consequence of the fusion of roots). Often this happens between members of the same species, but not always. Be that as it may, the herbicide can be transferred from the destroyed tree to the one that is not subject to destruction.
And such closure of the roots of trees of the same species occurs quite often.

Note! It is believed that on the eastern side the root system grows to the height of the crown, while on the western side it grows to ½ of this height. You can use this rule of thumb.

Alternative Methods

There are also several alternative ways, allowing you to make the tree dry quickly. Consider the most effective, and therefore popular ones. For the convenience of visitors, the information below is presented in the form of a table.

Table. How else can you process a tree so that it dries out.

Method number 1. Salt use	It has long been known that when salt enters the soil, it destroys vegetation. Therefore, salt can easily destroy the roots and the tree itself. It is advisable to use a salt solution if you are afraid that the vegetation near the tree may also be destroyed. Water the soil with the solution while it absorbs it. The concentration of salt depends on the size of the tree (the larger it is, the more it should be).
Method number 2. How to pave the roots	You can block the flow of moisture and oxygen to the roots - for this you just need to fill them with concrete to the very base of the trunk. After 2-4 weeks, the roots will die, and the tree itself, accordingly, will begin to dry. This method is advisable if a path is planned in place of the tree.
Method number 3. Blocking the air supply with mulch	The method resembles the previous one, but is more attractive and environmentally friendly. Lay a layer of mulch (from 15 cm) over the roots and up the tree itself. So you partially block the receipt nutrients and the tree will slowly die.

Note! By the way, if the roots are blocking the sewer pipe, you can use the Root Destroyer (if you can find it), which you just need to flush down the toilet. So you will only kill the roots that have penetrated the network, but do not harm the tree.

When the tree dries up, it is cut down and burned. But after that, roots remain in the ground, which can also cause a lot of trouble. Below is small instruction on mechanical removal stump.

Video - How to remove a stump chemically

Sometimes homeowners have a problem, which is the need to destroy a growing tree in the wrong place. The article will discuss how to do this without cutting, quickly and imperceptibly.

Destruction by watering the soil with chemicals

You can quickly destroy a tree without resorting to cutting down with the help of herbicides. The following drugs are considered the most effective here:

Zencor;
Meister;
Prometrin.

The process itself looks like this:

Pre-soil around the tree must be well moistened. On dry soil, the substance will penetrate to the roots for a very long time.
Thoroughly water the soil around the trunk with a solution of herbicide.

Attention! When working with herbicidal substances, you must strictly adhere to the instructions and follow the safety rules. Otherwise, you can harm your health.

How to bring a tree to death with injections

To destroy a tree in a similar way, you will need the following tools and devices:

Drill with a suitable drill 5-10 mm in diameter.
Ordinary medical syringe.

Attention! The most effective application of this method is achieved by introducing the drug into the circumference of the trunk every 5-10 cm.

Direct injections are carried out as follows:

At a height of at least 1 m from the ground, holes 5-6 cm deep are drilled with a drill. In this case, it must be taken into account that each of them should be located at an angle of 50 ° relative to the ground.
Using a medical syringe, the drug is poured into the holes. To prevent leakage of liquid, each hole should be covered with earth. Soon the plant will begin to noticeably dry out.

Drugs that are suitable for the technique:

ground;
Tornado.

Chemicals can be used to destroy a tree

Attention! If you take heavier herbicides, their main substances can penetrate the soil and kill neighboring plants.

Applying funds to wood

An effective method for removing unwanted vegetation is to apply appropriate preparations to the bark. Suitable means for this option are:

Glyphos;
Roundup;
Tornado;
Arsenal.

Advice. The technique is best suited if it is necessary to selectively remove a small number of trees.

Depending on how thick the bark of the tree is, the poisonous substance is applied in different ways:

directly on the surface of the cortex;
through the incisions made.

Advice. Before processing a tree, it is better to mix the poisonous substance with oil. This will speed up its absorption.

In the presence of a thick bark, the first option will not work. This is where the cuts will need to be made. As a tool, it is better to use an ax. With its help, deep notches are made around the trunk. Cut down areas are abundantly watered with herbicide. Be sure to consider that the procedure will work quickly in cool, dry weather. Atmospheric precipitation can wash away the poisonous liquid and all work will go down the drain.

How to remove the root after drying

After the tree has dried up and been cut down, a stump remains on the surface, and roots in the ground, which presents certain inconveniences to the owners of the site. Two methods are used to quickly remove stumps:

applying funds to the cut itself;
lubrication of notches.

A 10% solution of butyl ether works very well for this job. If you want to remove several stumps, then in this case, use saltpeter. The procedure is carried out like this:

Holes are drilled in the remains of the tree.
Fill them with saltpeter.
All holes are closed with stoppers.

In this form, the tree is left until the next season. During this time, it will dry thoroughly, after which it will be much easier to remove the stump and roots.

Removing an adult tree is a complex and time-consuming process. However, with the help of the above methods, it can be greatly simplified.

How to get rid of a tree: video

Questions regarding the maintenance of trees in a garden plot usually come down to the search for recipes for the preservation, strengthening and development of plantings. Summer residents and gardeners strive to create maximum conditions for the full functioning of the root system, trunk and crown. Nevertheless, there are also questions of a different kind - for example, how to water a tree so that it dries up? Such radical methods of getting rid of vegetation seem inhumane, but there are times when there is simply no alternative.

Chemical removal of the tree may be required in particular when the trunk has a diameter of more than 30 cm and the space around it is occupied by buildings or other plantings. Accordingly, it is extremely dangerous to fell or cut down such a tree, and slow killing will not cause serious trouble and will lead to the intended goal. The main thing is to choose the optimal means of processing a tree that contributes to its withering.

The effect of chemicals on the destruction of trees

Chemicals used in agriculture and horticulture for drying trees, have an impact on the entire root system. When determining how to water a tree so that it dries quickly, it is necessary to take into account the properties of the soil. In some cases, additional treatment with the composition of the living tissues of the plant and bark may be required. Also, for maximum effect, it is worth considering the possibility of cutting the trunk, and then proceed to the processing of the stump. This will speed up the process of getting rid of an unwanted object on the site. Now you can figure out in more detail which chemicals will help in such operations.

Saltpeter sodium

It is also called potassium. Usually this option is used in relation to stumps, but it can also be applied directly to the soil layer or directly to the trunk. This is the best way for those who are looking for something to water the tree to dry out, among folk ways. If the composition is introduced into an artificially created hollow, this will entail a more intensive process of drying the tree from the roots to the top of the crown. After about a year, the wood will lose its ability to live, and it can be burned. If standard watering is used with the composition, then drying may be delayed - but in any case, after a few years, the expected effect will be provided.

Ammonium nitrate

Principle of operation and nature of use this tool similar to the previous one, but there is one difference. In a year, you will not have to set fire to the tree, since ammonia-based (or urea) saltpeter provides an accelerated process of decomposition of the wood structure. This is important point, since many novice gardeners are not only interested in how to water a tree so that it dries up, but are also looking for ways to most easily and harmlessly remove plant debris. So, when using ammonium nitrate, even the root system literally mixes with the soil, providing a nutritious fertilizer. The core of the trunk itself, at the first signs of drying, you can try to uproot, and pour the solution again onto the formed place - especially for the roots.

herbicides

A whole group of drugs with which any vegetation is destroyed. There are also special means to control specific varieties fruit trees. Such preparations contain glyphosate, a substance that poisons all vital systems of a plant, contributing to its rapid drying and causing inevitable death. Answering the question of how you can water a tree so that it dries up, you can call "Tornado" and "Roundup". These drugs are used to destroy unwanted fruit and valuable tree species. Also, these tools have found application in the reconstruction of low-value deciduous young growth, when working with mixed young trees and in the removal of forest stand in coniferous varieties.

The drugs "Arbonal" and "Arsenal" are also common. They have a continuous effect on the trees. Their composition includes the substance imazapyr, which increases the chemical effect. Thanks to this additive, you can resolve the issue of how to water the roots of a tree so that it dries out even in the case of perennial plantings. The effectiveness of such products is also evidenced by the fact of their use in vast forests, nurseries and agricultural lands, where they demonstrate high penetrating ability.

"Pikloram"

Enough effective drug, from which you can prepare a solution to suppress the growth of unwanted trees and shrubs. Its advantages, in addition to a good result, include wide opportunities applications. For example, it is also used as a spraying agent - sometimes it is more effective than watering a tree so that it dries quickly after working the soil. True, Pikloram also acts quite productively on the soil layers. The solution leaches into deep layers of soil, as a result of which the root system dies. This action can be compared with benzoic halogenated acids, which, however, have lower phytotoxicity.

Chemical Application Technique

There are several ways to treat trees and root systems with chemicals to destroy them. The most common is watering. Most gardeners are wondering exactly how to water a tree so that it withers and dies. Abundant watering will give positive result if you moisten the surface of the soil before doing it. This will speed up the passage chemical elements to the roots of the tree. In some cases, such operations also use concrete barriers, within which the substance is concentrated and has the greatest effect.

Alternative uses for chemicals

In the process of watering, chemicals penetrate to the roots, acting on which they cause the entire tree to dry out. But today, other methods of introducing compounds are also practiced - this can be injection, processing foliage, bark and creating special cuts with holes into which the solution is poured. Having decided how to water the tree so that it dries out, you can use the above methods in combination. That is, water the root system with saltpeter, and then introduce the herbicide through the notches or cuts. If the method of action through living tissues is used, then it is desirable to provide for the characteristics of the movement of juice in a particular variety. The fact is that in the spring, the juice flowing from the wound can become a barrier to the absorption of the chemical.

What should be considered when using chemicals?

The use of chemicals inevitably requires compliance with safety precautions, as well as rules for use. One of the main problems with this approach to the destruction of woody vegetation is the detrimental effect on the soil. Specialized preparations, as a rule, are free from side effects in the form of a deterioration in soil fertility, but this aspect should still be taken into account when choosing which solution to water the tree so that it dries along with the roots.

Conclusion

Watering trees with chemicals to kill them is quite effective, but it also entails the need to comply with a number of conditions. The use of a solution that is optimal in composition for a particular tree will eliminate the need for complex and time-consuming mechanical uprooting operations.

On the other hand, there is a risk of damaging the soil layer. Therefore, when determining how to water the roots of a tree to dry out, a multilateral analysis of the chemical should be carried out. In addition, we must prepare for the fact that the drying process will not be fast. On average, it is 1-2 years - depending on the characteristics of the drug used. Sometimes garden chemistry becomes the only possible way to remove unwanted vegetation. In particular, this applies to the stumps left after sawing. In other situations, it makes sense to consider possible ways problem solving and by mechanical means, which, however, also have many of their shortcomings.

There are situations when an old tree interferes with plantings and residential buildings, and it is problematic to eliminate it with a tool. In this case, the question arises of how to destroy the tree unnoticed. Watering and treatment with chemicals will help, which we will talk about in more detail.

Methods for processing trees for their destruction

There are several ways to get rid of an emergency and simply interfering tree with the help of chemicals:

introducing chemicals into the soil;
crown processing on foliage;
the use of drugs on the bark of a tree.

Applying chemicals to the soil

The most effective and least time-consuming way to dry a tree is to apply it to the ground. trunk circle herbicides. Usually this method is used to eliminate a large number of old wood, for example, in neglected areas.

To speed up the action of herbicides, the soil is pre-moistened or heavy rainfall is expected.

If several trees are to be destroyed, a little dye is mixed into the herbicide solutions in order to visually distinguish the already treated areas.

In the case when one tree needs to be destroyed, and healthy, fruitful crops grow around, concrete or wooden barriers are installed inside the soil. Herbicides can harm neighboring plantings, and they should be secured.

Work with chemicals in protective clothing, be sure to wear gloves and with a respirator on your face to prevent the solution from getting into the mucous membranes of the eyes and nasopharynx.

How to water the trees:

"Prometrin",
"Zenkor",
Mays Ter.

crown processing

Spraying vegetative mass with pesticides also refers to simple and effective ways how to get rid of a tree. Most often, crown treatment is used to eliminate shrubs, but leaf treatment can also be used to destroy more massive wood.

The procedure is carried out in autumn or spring, since spraying in summer in hot weather is less effective. Doses are calculated based on the susceptibility of the culture. The browned vegetative mass of the crown will tell about the action of the remedy.

Leaves are best at absorbing pesticides. oil based, which means that the process of eliminating wood will go faster than when using aqueous solutions. However, oil preparations are much more toxic, this must be taken into account and all safety measures must be observed.

How to spray the crown to dry the tree:

"Tornado",
"Roundup"
"Arsenal".

How to process the bark

When applied chemical compositions the bark is affected by living plant tissues. This method is effective and allows you to selectively destroy objects without causing damage to neighboring plantings.

How to process the bark: "Arsenal", "Glyphos", "Tornado", "Roundup".

Tree poison can be applied:

on the surface of the bark;
through incisions in the bark;
vaccinations.

On the surface of the bark

The application is effective for trees and shrubs with soft, thin bark. A solution with a pesticide is applied to a section of a tree located half a meter from the soil level in a circle. So that the product is better absorbed and does not flow, oil is added to it. The wood is smeared until the surface completely absorbs all the agent.

You can perform the procedure at any time of the calendar year, unlike watering and spraying with chemicals, which are carried out only in spring or with the onset of cool weather. autumn days. Open wounds with intense secretion of juice, which blocks the absorption of pesticides, will be a contraindication to conduction. In this case, the irrigation or leaf treatment method is used.

Through the incisions

If the wood has a thick bark, ordinary spreading will not give a noticeable result, so poison for trees is served through cuts. Perform cuts in a circle at a height of 1.5 m from the ground level with a saw or an ax. Choose a non-hot day for work, should not be observed strong wind. If precipitation has passed, work is postponed for 4-5 hours.

Vaccinations

To perform injections, notches are first made on the wood, into which a syringe or device for injecting the agent will then be inserted. Notches are made at a height of one meter along the trunk in a circle, the step between the holes should be 5 - 7 cm.

Vaccinations with pesticides to destroy wood - the safest for environment way. Suitable only for trees whose trunk diameter exceeds 5 cm - 10 cm. The algorithm of actions is as follows:

Prepare a drill with a 5 mm - 10 mm drill.
Make holes according to the scheme described above to a depth of 4.5 cm - 5 cm. Notches are drilled at an angle of 45 ° - 50 °.
For large trees, special sprayers are used; for trunks of small diameter, a conventional medical syringe is suitable. Fill the tool with herbicide and insert it into the holes made.
Seal the notches with soil so that the drug does not drain.

The injections are very effective, the tree begins to dry out within the first week. For vaccinations, you can use the means "Glyphos", "Ground", "Tornado". The drug "Glyphos" is administered at a concentration of 200 ml / 1 l due to severe toxicity, the rest of the drugs are used undiluted.

Destruction of the stump and rhizome

Ideally, the elimination of unnecessary wood is carried out by a complex method, when the tree trunk is cut down, and the remaining stump is treated with herbicides. Please note that pesticides can only be used on a fresh stump, and only its outer edge is treated. The roots of the stump are cut, and after the wood dries out, the stump is uprooted from the ground.

Treatment of trees from pests and diseases;

See here how to use the leaves as fertilizer for the soil;

Sleeping tea as a fertilizer:

Chemicals that cause drying of trees

As we have said, the most effective for the elimination of trees are herbicides:

Roundup and Tornado are used for the rapid destruction of a tree, effective for deciduous crops and conifers;

Picloram more often used for soil or crown treatment, the substance inhibits the roots, the tree dies;

Arbonal and Arsenal penetrate the wood well, so these products are used to treat the bark.

There are many such preparations, and in a gardening store you will definitely find a suitable remedy. However, it is not always possible to purchase herbicides. In this case, they will help mineral fertilizers:

Ammonium nitrate in large doses, it is dangerous for living plants and greatly accelerates the decomposition of wood. Fertilizer is injected into hollows or specially made holes, then the wood will dry out very quickly - in just a year. If a ammonium nitrate water the root system, the wood will dry out for several years.

sodium nitrate traditionally used to remove stumps, but this tool is also effective for eliminating a full-fledged tree. The action of sodium nitrate is similar to the previous remedy, it is used for incorporation into the soil and laying in hollows.

Folk remedies for the destruction of trees

And, of course, there are several folk ways to make the tree dry without any trace of any mechanical impact:

Salt has long been used by rural residents to destroy old wood. Salt kills all vegetation. In order not to harm neighboring trees and plantings in the garden, the substance is used not in its pure form, but in solution. The concentration is made arbitrary depending on the age of the wood: than older tree, the salt should be more.

dense mulch, laid in the trunk circle, will prevent the supply of nutrition to the rhizome. The method is environmentally friendly, but it will take several years to get the result. The layer of mulch should be at least 15 cm.

Concrete applies if the tree grows on garden path or near a fence. The roots and part of the trunk circle are poured mortar, which will block the flow of moisture and nutrients. Within 15 - 30 days, the roots will die, after which the process of drying the wood will begin.

After treatment with chemicals or folk remedies, the tree dries up. It must be cut off and be sure to burn, as chemicals partially remain in the dead tissues. The roots of the stump are cut and uprooted. In some cases, additional processing of the wood remaining in the ground is carried out.

The unfortunate location of the tree near residential buildings and playgrounds poses a direct threat to human life, sometimes it simply interferes with the arrangement garden plot, and its elimination is a necessity. But, nevertheless, it should be remembered that trees are living organisms, and destroy them without good reasons not worth it.
Folk remedy for toenail fungus vinegar essence Uterine fibroids in combination with endometriosis treatment with folk remedies

Article plan

Methods for processing trees for their destruction

There are several ways to get rid of an emergency and simply interfering tree with the help of chemicals:

introducing chemicals into the soil;
crown processing on foliage;
the use of drugs on the bark of a tree.

Applying chemicals to the soil

The most effective and least time-consuming way to dry a tree is to apply a circle of herbicides to the ground. Usually this method is used to eliminate a large amount of old wood, for example, in neglected areas.

To speed up the action of herbicides, the soil is pre-moistened or heavy rainfall is expected.

If several trees are to be destroyed, a little dye is mixed into the herbicide solutions in order to visually distinguish the already treated areas.

In the case when one tree needs to be destroyed, and healthy, fruitful crops grow around, concrete or wooden barriers are installed inside the soil. Herbicides can harm neighboring plantings, and they should be secured.

Work with chemicals in protective clothing, be sure to wear gloves and with a respirator on your face to prevent the solution from getting into the mucous membranes of the eyes and nasopharynx.

How to water the trees:

"Prometrin",
"Zenkor",
Mays Ter.

crown processing

Spraying vegetative mass with pesticides is also one of the simple and effective ways to get rid of a tree. Most often, crown treatment is used to eliminate shrubs, but leaf treatment can also be used to destroy more massive wood.

Best of all, foliage absorbs oil-based pesticides, which means that the process of eliminating wood will be faster than using aqueous solutions. However, oil preparations are much more toxic, this must be taken into account and all safety measures must be observed.

How to spray the crown to dry the tree:

"Arsenal".

How to process the bark

When chemical compounds are applied to the bark, living plant tissues are affected. This method is effective and allows you to selectively destroy objects without causing damage to neighboring plantings.

How to process the bark: “Arsenal”, “Glyphos”, “Tornado”, “Roundup”.

Tree poison can be applied:

on the surface of the bark;
through incisions in the bark;
vaccinations.

On the surface of the bark

You can perform the procedure at any time of the calendar year, unlike watering and spraying with chemicals, which are carried out only in the spring or with the onset of cool autumn days. Open wounds with intense secretion of juice, which blocks the absorption of pesticides, will be a contraindication to conduction. In this case, the irrigation or leaf treatment method is used.

Through the incisions

If the wood has a thick bark, ordinary spreading will not give a noticeable result, so poison for trees is served through cuts. Perform cuts in a circle at a height of 1.5 m from the ground level with a saw or an ax. For work, choose a non-hot day, there should not be a strong wind. If precipitation has passed, work is postponed for 4-5 hours.

Vaccinations

Vaccinations with pesticides to destroy wood are the most environmentally friendly way. Suitable only for trees whose trunk diameter exceeds 5 cm - 10 cm. The algorithm of actions is as follows:

The injections are very effective, the tree begins to dry out within the first week. For vaccinations, you can use the means "Glyphos", "Ground", "Tornado". The drug "Glyphos" is administered at a concentration of 200 ml / 1 l due to severe toxicity, the rest of the drugs are used undiluted.

Destruction of the stump and rhizome

Chemicals that cause drying of trees

As we have said, the most effective for the elimination of trees are herbicides:

There are many such preparations, and in a gardening store you will definitely find a suitable remedy. However, it is not always possible to purchase herbicides. In this case, mineral fertilizers will help out:

in large doses, it is dangerous for living plants and greatly accelerates the decomposition of wood. Fertilizer is injected into hollows or specially made holes, then the wood will dry out very quickly - in just a year. If you water the root system with ammonium nitrate, the wood will dry out for several years.
sodium nitrate traditionally used to remove stumps, but this tool is also effective for eliminating a full-fledged tree. The action of sodium nitrate is similar to the previous remedy, it is used for incorporation into the soil and laying in hollows.

Folk remedies for the destruction of trees

And, of course, there are several folk ways to make the tree dry without any trace of any mechanical impact:

After treatment with chemicals or folk remedies, the tree dries up. It must be cut off and be sure to burn, as chemicals partially remain in the dead tissues. The roots of the stump are cut and uprooted. In some cases, additional processing of the wood remaining in the ground is carried out.

The unfortunate location of a tree near residential buildings and playgrounds poses a direct threat to human life, sometimes it simply interferes with the arrangement of a garden plot, and its elimination is a necessity. But, nevertheless, it should be remembered that trees are living organisms, and it is not worth destroying them without good reasons.