Install a fence made of welded galvanized mesh. We make a fence from a welded mesh with our own hands. Welded mesh fence

The fence has two main purposes: to form the boundaries of the site and to create a barrier against the entry of unwanted guests. The appearance of the building is in third place. But today more and more this criterion moves to fourth place, displaced by the cost of the protective structure. Therefore, more and more owners suburban areas preference is given to mesh fences. They are highly reliable, but low price.

mesh fence

It is necessary to divide the mesh into two groups that differ from each other in the source material. These are metal meshes and plastic ones. The latter are rarely used for fencing sites, because they do not have sufficient strength. They are used for fencing flower beds, garden plantings and other structures.

In this regard, metal protective structures made of meshes are used everywhere. Because they have high technical and operational characteristics. Today, two types of nets are used for fencing: chain-link and welded.

They differ from each other in manufacturing technology. The first is made by the weaving method with the formation of cells, the second by the spot welding method, in which metal bars are joined.

It cannot be said that the welded mesh better than chain-link. Both have fairly high strength characteristics and almost the same advantages and disadvantages.

Advantages and disadvantages of welded mesh

The main advantage of fences from welded mesh– low price at high technical specifications. Next, we note:

the ability to dismantle the mesh and use it elsewhere for the construction of fences or other needs;
ease of installation;
a huge variety of proposed sizes, which makes it possible to build fences of different heights;
easily tolerates natural loads;
transparency of the structure, allowing air and sunlight to pass through, which is an important factor for some areas.

With regards to the shortcomings, the last plus is regarded by many as a minus. Not everyone likes when their personal life is wide open. A transparent design contributes to this. The second negative is not quite presentable appearance when compared with other protective structures, such as brick, stone or wood.

Not the most presentable

Varieties

The classification of welded mesh is based on raw material. There are three categories here:

Made from carbon steel without protective coatings. Weld it from metal rods with a diameter of 1.2-10 mm. Such products are subject to metal corrosion, therefore, over time, it becomes rusty. metal mesh of this type must be painted to reduce wear and tear. Staining is carried out with an enviable frequency, which increases the cost of maintaining the protective structure.
Galvanized. It is welded from galvanized wire, which practically does not rust under the influence of natural loads. It has a fairly long service life, there is no need to paint such a product. And yet it is not the best material.
not galvanized with polymer coated. In fact, this is the first option that is covered polymer layer. The finished mesh is simply dipped in polymer mass and then dried. To give the product a more presentable appearance, it is covered with paint on powder technology. This further increases the protective qualities.
Galvanized with a polymer layer. This is the pinnacle of the quality of metal meshes, but also the pinnacle of the price component. Welded meshes of this type can be attributed to materials from the category with an unlimited service life, although manufacturers guarantee 65 years. At the same time, this type of material can easily withstand temperature Range from -55С to +65С and humidity not more than 97%.

Note that welded meshes are treated with zinc using two technologies. The first is the manufacture of a mesh product from galvanized wire, the second is from carbon steel, and already finished mesh are galvanized. The latter option is better, because in the first technology, welding heats up the zinc layer of two rods, which reduces protective characteristics material. Often the zinc layer simply peels off from the body of the base metal.

In the construction market, the welded mesh is represented by two positions: rolled and in the form of layers. The second option is easier to install, because it is a finished product with its own dimensions, under which you just need to install support posts in increments equal to the width of the seam.

Galvanized fence with white polymer coating

Fence installation

Consider three installation options: in layers or, as they are called, sectional structures and roll.

Option number 1

First of all, you need to prepare all the required materials. Namely: a welded mesh, the layers of which are selected to match the height of the future protective structure, and support pillars, preferably from profile pipe with a section of 50x50 mm and a wall thickness of 2 mm. Pipes must be closed with metal square plugs on both sides (they are welded by electric welding) and painted with powder paint to match the color of the entire protective structure. Today they sell plastic plugs different size, shapes and colors.

The next stage is the planning of the boundaries of the site. To do this, pipes or fittings (can be used) are clogged in the corners of the site, which are tied with twine. The installation step of the support posts must be determined during the design of the fence, it is on the basis of this indicator that the layers are selected, or rather, their width. The standard step is 2m.

Under the racks it is necessary to drill wells half a meter deep

The installation sites of the supports are determined, in which holes with a depth of 0.5 m are immediately drilled. For this, a drill with a diameter of 200 mm is used. Prepared profile pipes are inserted into the pits and, with the help of a sledgehammer, they are hammered to a depth of 1 m. It turns out that half a meter of the pipe will be driven into the ground, half a meter will be concreted.

Pillars are hammered with a sledgehammer

Each pillar is set vertically using a building level and concreted with a solution of the classic recipe: 1 part of cement, 2 parts of sand, 3 parts of crushed stone. All supports must be set to the same height.

Now we need to install mesh layers. For their fastening to the poles, special U-shaped clamps are used, connected on the reverse side with a mounting plate, which is supported by two nuts. The number of clamps is 4 for each post. In this case, the grid must be strictly set in height, taking into account the installation of each layer.

Fastening mesh layers with U-shaped clamps

There is another option for fastening work, which is a long bolt and a special shaped washer. To do this, the racks at the places of fastening of the layers are drilled through to the diameter of the fastening bolt used. The layers are installed, bolts with washers are inserted into the holes, which are tightened with nuts on the reverse side. It is recommended to place a rubber or plastic gasket under the washer.

Mesh fastening with a bolt and a shaped nut

And another type of fastening is a special clamp that works for tightening. Choose it according to the size of the profile pipe used for the support posts. They compress both the pipe and the mesh laid on it with a clamp. Tightening is done with bolted connection. The photo below shows such a collar.

Clamp for attaching the welded mesh to support pillars

We offer you to watch a video on how to properly mount a welded mesh fence.

Attention! You can not drive the pillars into the ground. They are simply installed in a prepared hole 70-80 cm deep and poured with concrete. The main thing in this process is to install props under the racks so that they dry out concrete mortar supported the supports in a vertical position.

Option number 2

The installation sequence of this type of fence is different. And the mounting method is different.

You will need pipe-racks, in which holes are made every 40-50 cm, where special rivets are driven. The latter have internal thread for fasteners. The rivets are driven into the holes with an interference fit so that they do not rotate at the installation site.

Now the two posts are laid on the ground parallel to each other. A welded mesh is laid on them, which is attached to the pipes with a bolt and a special washer.

Fastening to racks with special fasteners

It turns out a finished section, which is installed in prepared pits and concreted as a separate element of the barrier structure.

Option number 3

Consider how the roll-type mesh material is attached.

The edge of the product is tied to the first post with a knitting wire.
The roll unwinds to the second rack.
Stretches to the max.
It is tied to the rack with wire in several places.

And so to the end of the fence. To prevent the mesh from sagging, you can pass a thick wire or steel rods along the upper and lower edges. This is how work is done to install a grid made of thin steel bars. The structure with greater strength is attached to the racks in other ways.

If the mesh is welded from rods not of the large diameter, then you can try to attach the finished product to the pillars with roofing metal screws. Not the most good option, because the head of the self-tapping screw is of small diameter, therefore, a tight fit to the surface of the profile pipe is not guaranteed. There is a high probability that the mesh will pop out from under the fasteners in the process of wind pressure or ground displacement. You can try to put a wide washer under the self-tapping screw, but this is not the best solution. Although both methods are often used when installing grids made of small wire.

Fastening to metal risers with roofing screws

Optimal - make a puck rectangular shape, into which two self-tapping screws will be screwed at once. The mesh rod located on the post will remain between the two fasteners, and this will not allow it to move along the post. And the washer will keep it from moving in the horizontal plane.

Roofing screw for fastening a welded structure

Can be used roofing screws with profile washers, as in the photo above. They simply attract the mesh to the rack, so the washer must be selected according to the dimensions of the profile pipe so that the latter is inside the washer.

The fence assembly technology is almost the same in all the situations described above. But there are many ways to attach a mesh product to racks. Therefore, one is chosen that is easier in the process of doing the work with one's own hands.

Photo gallery

Painted fence assembled from welded mesh on U-shaped clamps

Protective structure made of welded mesh

Fence assembled according to the type of 3D welded mesh construction

If you want to save money, you can make a fence from a welded mesh with your own hands. Such a design is suitable option both for cottages and private homes. However, first you need to choose the material, since it should be understood that the welded mesh can be of several types. The quality of the entire product will depend on the material chosen.

You should be aware that not all types of fences are allowed to be mounted between closely spaced areas. This is due to the fact that monolithic structures high altitude shade the space. Given the small size modern dachas, then it should be understood that in this case, almost all plants in the garden will grow sluggish. For this reason, there will be constant complaints from the owners of neighboring plots. The way out is the use of a mesh that is not an obstacle to the light of the sun and air masses.

A mesh fence can be used not only in the country, but also to enclose sports facilities, technical grounds or reservoirs.

Today there are such types of networks:

Galvanized mesh. A layer of zinc is applied to steel parts. This is done before or after welding. it best option in case there is a desire to get a durable design for little money.
Non-galvanized mesh. This material is the simplest and requires minimal cash costs. This product is made from steel. The diameter of the bars is approximately 1.2-7 mm. The disadvantage is that such a product does not have a coating. it a big problem, as there is no protection from the influence of external factors.
Galvanized product with a special coating. This option is durable. The only downside is the high cost.
Polymer coated product. Has protection against corrosion and other factors.

How to mark up your own site?

First of all, you will need to mount temporary pegs in the corners of the territory, between which the thread will be pulled. The length of the cord will be desired mesh, however, it will have to be bought with a margin of several meters. After that, you should designate the places where the columns will be placed. The recommended distance between the columns is 2-2.5 m. If you make a larger distance, then the lattice may begin to sag.

You should be aware that on a site with a large slope it will not be possible to install a mesh fence, since it is impossible to securely fix the material at an angle.

In this case, the only way out is the terracing of the site, which involves the installation of columns of greater length and strength at the places of difference. On one side of the column, the grid will be fixed at a level above, and on the other - below. To do this, the grid will need to be cut into individual elements. If it is not possible to do this, then you can install a sectional fence for a summer cottage.

On the this moment There are two ways to build a mesh fence. The first method involves the tension of the lattice between the posts. To implement the second method, it will be necessary to make metal corners into which the elements of the lattice will be fixed. The first option is easiest to do, but it should be noted that it is less durable and attractive from an aesthetic point of view.

For the manufacture of sections will need additional expenses Money. The cost of a corner can significantly exceed the cost of the mesh itself.

In all cases, the installation of a welded mesh fence involves the use of posts. These elements can be built from metal or wood. The first option is budget and affordable. However, you should buy wooden supports only if their cost is several times less than a metal product. Also wooden structures suitable in case you need to install only a temporary product.

There are also situations when the material remains after the construction of a private house, and there is no desire to throw it away. In order to exclude extra costs, you can apply the existing columns.

Metal posts will last for many years. The most commonly used support elements with square section, their diameter is in the range from 7 to 12 cm. The thickness of the tube wall must be more than 2 mm. If you want to save money, you can purchase material at a scrap metal point, where great options pipes.

Back to index

How is a mesh fence installed?

To work, you will need a screwdriver, building level, tape measure, bayonet shovel, pegs.

If it was decided to install a mesh fence, then the first step is to prepare everything the right tools and materials. To work, you will need the following elements:

metal poles for the construction of a frame structure;
elements for fastening posts (bases, clips for connection, brackets with nuts and bolts and clamps U-shaped);
roulette;
water;
screwdriver;
pegs;
cement mixture;
building level;
concrete mortar for the base of each column;
sand;
rope;
bayonet shovel, with which it will be possible to dig holes for posts.

Back to index

The sequence of actions for installing the fence

To install a fence from a welded mesh with your own hands, you need to perform the following steps:

The first stage of installation is marking. The perimeter is preliminarily outlined and the location of the fence is indicated. You can measure the distance between the pits with a tape measure. The distance from one column to another is equal to the width of the sheet, however, the diameter of the column and the margin for the base should be taken into account. For example, with a cut width of 2 m and a column diameter of 10 cm, you should measure the distance between the supporting elements, which is 2.18-2.2 m.
The next step is to dig holes. Their diameter must be larger diameter columns by 1-3 cm. It is important to take into account the base of concrete or cement. This must be done with a drill. If this device is not available, then you can use an ordinary bayonet shovel. The depth of each hole should be approximately ¼ of the length of the column. However, the depth of soil freezing should also be taken into account. The larger it is, the deeper the holes should be. In most cases, columns 2 m high are prepared. In Russia, winters are quite severe, therefore, approximately 15-20 cm must be added to 50 cm (¼ of the height of the supporting element). In this way, you can get the depth of one hole.
At this stage, the installation support posts. Pour the cement mixture into the hole. To prepare it, you need to mix one part of water with one part of a mixture of cement and three parts of sand. Next, you need to insert a column. It should be noted that in some cases it is placed in a special base. The column is leveled using the building level. It is necessary to hang the tool on the top of the post and make sure that the level is placed perpendicular to the ground and parallel support element. Next, the device must be fixed with spacers and wait until the base hardens.
After about 24 hours (on average, this time is spent on solidifying the base), you can begin to install the grid. It should be fastened with special fastening elements or U-shaped clamps. For fixing you need to use a screwdriver. The grid is recommended to be fixed in several places of support. If the mesh is not cut into sheets, but is fixed in a roll, then staples should be used for this. Special attention it is necessary to pay attention to the fasteners, since the reliability of the entire device will depend on them.
At the end, the mesh fence will need to be painted with moisture-resistant paint.

A fence made of welded mesh has become in our time a great alternative to a chain-link mesh. Such a fence is not inferior to other options in terms of quality and durability, and it is much easier to install and maintain it.

In addition, the fence made of rolled welded mesh looks quite decent. It does not block access sunlight to the site, but will protect your property from uninvited guests.

You can order the installation of rolled fencing from the masters. You can do this at http://sitka.com.ua/ru/zabory/. Experts will take measurements, select the material and install the fence in a short time.

You can also try to make a fence from a welded mesh yourself. The installation technology is not too complicated, so it will not be difficult to cope with it.

Why is wire mesh fence popular?

If you do not plan to enclose the site with a solid fence, then welded mesh will be the best solution for you.

It is affordable.
Has light weight.
The mesh has a long service life and is highly durable.
Installing a mesh fence does not take much time.
The installation itself is simple.
The mesh does not interfere with normal air circulation and lighting of the area.

We can say that the welded mesh fence is the best value for money. Quite a budget option for fencing suburban area or cottages.

The mesh itself is an interlacing of thin strong wire, which, at the bonding points, is spot-welded. When choosing, you should pay attention to the thickness of the wire and the dimensions of the weaving cells.

The thicker the wire and the smaller the cells, the stronger fence. Also consider the manufacturer's classification, which will help you choose the material suitable for specific conditions operation.

Galvanized mesh is very strong and durable, it is not afraid of water, and it retains its original appearance for a long time.
Polymer-coated mesh is additionally protected from damage and adverse weather conditions.
Polymer-coated galvanized mesh is the most expensive material, but it is doubly protected.
Finally, a non-galvanized mesh is a budget option, it is better to paint over it thoroughly after installation so that the fence lasts longer.

The fence itself can also be of two types. The tension fence is a mesh stretched around the perimeter of the site, reinforced with pillars.

The sectional fence is much stronger, but its installation is more expensive and time-consuming. In this case, the mesh is stretched metal carcass, and the fence itself is a section.

Installing a tension fence made of welded mesh

Installation tension fence the simplest option. Your task is to stretch the mesh between pre-installed metal poles and secure it.

Supports are installed for every two meters of the fence. The installation process itself consists of several stages:

Marking is applied along the perimeter of the site and a construction rope is pulled for installation accuracy.
Determine the location of the supports. In place of the support, a hole is dug a meter deep. At the bottom of it you need to pour crushed stone and sand.
A post is placed in the hole and covered with soil. If it's about metal poles, instead of the earth it is better to use a concrete solution.
After installing the pillars, you can begin to tension the mesh. It is best to do this from the corner of the site. To the first post, the end of the roll must be carefully attached to ensure sufficient tension.
The roll is unwound to the next support. Here, a metal rod is inserted at the necessary mark across the entire width of the material. Then the whole structure is attached to the support with clamps.
Thus, the mesh is stretched along the entire length of the fence.

When fixing the roll to the first post and further attaching the mesh to the supports, it is better to use thin metal rods. This will avoid further deformation of the material and sagging of the mesh in the spans.

Do not forget to paint the supports after installation to protect both them and the mesh from corrosion.

Some dacha cooperatives do not provide for installation between plots or any other similar material, since such structures obscure small areas. At the same time, a fence made of welded galvanized mesh becomes an excellent way out. It will not prevent ultraviolet radiation from entering the area, will not make it difficult natural circulation air and can be erected by any summer resident.

Training

The chain-link represents inexpensive material, which is ready to serve for quite a long time. As an additional advantage, it can be used as a support for climbing plants. This grid was invented at the end of the 19th century, but is still widely used today. Every consumer can buy it.

To create a fence, in addition to the mesh, reinforcing bars, thick wire, and a cable should be prepared. When choosing a grid, you should pay attention to the size of the cells. The smaller it is, the more expensive the mesh will be, but also stronger. If the mentioned parameter is equal to the limit of 40 to 50 mm, and the width of the roll is 1.5 m, then this material will become great solution to create a fence for a suburban area.

Tension fence

A fence made of welded galvanized mesh can be stretched. This method of its manufacture is the simplest. After all, the material will have to be stretched between the pillars, which can be made of the following materials:

concrete;
wood;
metal.

The number of supports will depend on the step between them and the length of the fence itself. The best distance is a parameter of 2.5 m. Pipes can be used as poles, but they must not be damaged by corrosion. On sale today you can also find ready-made poles that have hooks and a painted surface. before installation, it must be treated with a protective compound.

As an alternative solution, the mesh is fixed to them with a clamp or wire. The height of the pillars must be calculated. If the clearance between the ground and the fence is between 5 and 10 cm, then this parameter should be added underground part supports and grid width. The load on the corner posts will be greater, so they must be placed deeper than the rest. Therefore, their length should be 20 cm longer than the length of ordinary pillars.

When making a fence from a welded galvanized mesh, you should concrete the bases of the supports to increase strength. The pillars will be the frame of the structure. After installing them, you can begin to fix the grid. As soon as the concrete hardens, hooks are fixed to the posts or welded on if the post is metal. As a material for fastenings, you should use:

wire;
nails;
rod;
screws.

You can use any other material that bends into hooks. At the same time, the roll is straightened and installed at the corner support, the mesh must be hung on hooks.

The roll must be rewound one span to reach the next post. The rod is threaded a little further than the place where the mesh will be connected to the post. The master should hold the rod and pull the net. If the rod is not used, then the mesh may be stretched unevenly.

It is better to carry out these works with the help of another person. He will hold the mesh at the bottom edge while the other master at the top. At the next stage, reinforcement is threaded into the mesh, 5 cm must be retreated along the edges. When installing a fence made of welded galvanized mesh, it is necessary to weld horizontal bars or attach to poles.

Without using rods, over time you will encounter the fact that the mesh will sag. In the case where the technology is followed, the rods are used to maintain tension. The mesh should be pulled further according to the principle described above, fixing and pulling the rod or wire. On this we can assume that the fence is almost ready. Hooks are bent on poles, the last of which are painted. It is recommended to wrap the wire antennae down to reduce the risk of injury. The wire is usually threaded through the upper edge of the row of cells, the protruding edges should be wrapped around it.

sectional fence

For erection sectional fence you will need sections where the grid will be installed. At the first stage, you should use a technology that is similar to the one described above. For this, the territory is marked out, and then the pillars are installed.

The installation of a mesh fence will involve the use of a corner, the dimensions of which are 40 x 5 mm. These elements will be needed to make the frame. Its length is determined taking into account the distance between the pillars, 15 cm must be subtracted from this value. The same amount should be subtracted from the height of the pillar above the soil level. This will get the width of the frame.

Corners need to be welded into rectangular structures. The size of the sections is made taking into account the size of the mesh, which varies from 1.5 to 2 m. The welded galvanized mesh in rolls, if necessary, can be cut with an angle grinder.

Work methodology

At the next stage, metal strips are welded to the posts. They should be placed horizontally. Their length can be from 15 to 25 cm. As for the width and section, they are 5 cm and 5 mm, respectively. With a deviation from the edge of the column of 20 cm, it is necessary to install a section between two supports. For this, welding is used. The next step is to paint the fence.

Fence cost

Quite often, summer residents and owners of territories within the city are wondering how much a galvanized mesh fence costs. If the width of the material is 1.5 m, then you will have to pay 310 rubles for such a fence. per running meter. Using a grid whose width is 1.8 m, specialists charge 390 rubles for their services. per running metre.

Broach reinforcement will cost the consumer 40 rubles. per running metre. You may also be interested in the question of how much a fence costs. If its length is 50 m or more, then 355 rubles will have to be paid per linear meter. This price is correct for structures in which the reinforcement is installed in one row. The mesh width is 1.5 m. This parameter will be equivalent to the height of the fence. If it increases to 1.8 m, then the cost will rise to 415 rubles. The price includes metal supports, broach reinforcement in one row, galvanized mesh and installation work.

Mesh cost

If you decide to do the work yourself, you can ask about the cost of the grid. If the diameter of the wire used is 1.2 mm and the mesh size is 10 x 10 mm, then pay for square meter material will have 455 rubles. The price per roll in this case will be 6825 rubles.

The galvanized mesh, the cell of which is 20 x 20 mm, will cost the consumer 234 rubles. per square meter. In this case, the diameter of the wire used is 1 mm. But the price per roll will be equal to 7020 rubles. With an increase in the cell size to 25 x 25 mm, the cost rises to 416 rubles. per square meter. In this case, the wire diameter is 2 mm, and the price per roll will be 12480 rubles. Welded galvanized mesh 50x50 mm will cost the consumer 312 rubles. per square meter, while the price of the roll will be 7020 rubles, and the diameter of the wire will be 2.5 mm.

Conclusion

Galvanized welded mesh in rolls will be an excellent material for making a fence. It is easy to cut, it is quite simple to pull it between the supporting posts, in addition, it is durable. And in some cases, the grid is the only right solution when it is necessary to protect the site, but it is required to provide access to sunlight.

The fence performs not only the function of protecting property from the penetration of strangers, but also an aesthetic, decorative function, being an ornament land plot. While earlier stones, bricks, wood were used for fencing, modern welded metal meshes allow you to quickly recreate the fence. required height, strength and custom design.

The advantage of fences made of welded mesh

Sectional metal fences made of welded mesh are lightweight, they are durable and resistant to aggressive external influences, the installation of such fences is not laborious, it is done by hand in a short time, besides, the mesh does not create shadows and is optimal in pricing policy. When defects appear, it is easy to replace damaged areas.

Welded mesh for the fence - photo

Types of metal welded mesh for the fence

Metal meshes are made by welding wire of various thicknesses at the points of contact (spot welding). At the same time, cells can be of very different sizes and shapes - from standard square and rectangular to unusual polygonal (rhombus, trapezoid and others). A layer of polymer or other coating is applied to the surface of the grid to protect it from corrosion. The result is a canvas, which is used for fences.
Varieties metal mesh for the fence, depending on the type of coverage:
Welded mesh with a polymer (polyvinyl chloride) coating, usually such a mesh has a green or other color. The polymer is applied to the surface of the wire by immersing it in a solution or applying powder dyes in special cabinets.
Grid welded galvanized and non-galvanized. The manufacturing process may differ in the order of steps. Either the already galvanized wire is welded, or, on the contrary, a mesh is produced, which is then galvanized or sent for sale uncoated.
Grid welded with galvanization and polymer coating. This mesh is the most durable, but at the same time very expensive. For a conventional fence, the use of such a grid is impractical.

The mesh is produced and delivered to consumers in the form of panels and rolls. Rolls are produced weighing from 50 to 500 kilograms, up to two meters high. The length of the mesh in a roll is from 15 to 33 meters.

Installation of a sectional metal fence

The first stage is to study the territory, as well as measuring the required length of the future fence.
In places where the fence will pass, you should level the soil, remove shrubs and trees, remove large stones and foreign objects.

Installation of supporting pillars without the use of concrete.

Racks before installing them in the ground (concrete) must be protected from corrosion. To do this, we apply a layer of paint, bitumen on the lower part of the columns, or wrap them with a piece of roofing material.

The convenience of installing support posts without the use of concrete lies in the fact that without the use of concrete, you can install a fence at any time of the year, even in winter. Besides, installed fence easy to dismantle if necessary. The method is optimal for installing a fence on heaving soil.

We will literally hammer the fence into the ground. Therefore, it will be necessary to prepare small diameter depressions in the soil for supporting pillars. All wells must be of the same depth and located on the same line, so that the fence eventually comes out perfectly even. The distance between wells takes from 250 to 300 cm.
We insert metal racks into the prepared recesses and hammer them into the ground. The depth of the wells is taken equal to 1/4 of the length of the support column. However, if the depth of soil freezing is too high, then the depth of the pit should be increased.

Pay attention to the verticality of the installed pillars and their height, which should be equal along the entire perimeter of the fence. Use a tape measure, building level and threads stretched over pegs for easy alignment of the supports.

In the space between the soil and the walls of the pillars, we fill it with a butch of fine fraction (a mixture of crushed stone or gravel with sand) and carefully tamp.

Careful tamping ensures the immobility of the pillars and the strength of the installation of the fence.

Installation of supporting pillars with concreting

Similarly to the first method, it is necessary to mark out a place for wells on the site, dig them out, checking the distance between them and the depth.
We insert racks into the dug wells and fill them with concrete mortar.
So that the pillar does not deviate, for the period of hardening of the concrete solution (two days), it should be strengthened with spacers.

Particular attention should be paid to the pillars located in the corners of the site and those on which the gate (gate) will be fixed. Such racks require particularly strong fastening, as they bear additional loads.

The foundation for the fence tape monolithic

Such a foundation is able to withstand significant loads and provide proper reliability and stability to the future fence.
Before starting work, you should make markings and dig a trench. In this trench, we additionally dig holes for the pillars. Install wooden formwork into the trench. We lay reinforcement for strength. We install racks and fill the entire trench concrete mix. We strengthen the pillars with spacers for the period of solidification of the solution.

Fastening the metal mesh to the supporting poles
In order to fasten a sectional metal fence to the supporting poles, you will need: brackets with bolts and nuts to ensure that the mesh is pressed against the pole (or clamps instead of brackets); connecting clips for joining canvases, a screwdriver, corners, a welding machine.

We prepare sections of a fence for installation. We lay them out next to the racks.

We weld metal corners on the racks. They will serve as a fastener for the fence sections.
In the corners of each section, we drill holes through which we fasten the sections with screws.

Another method allows you to do without connecting brackets, but it will be difficult to dismantle the fence if necessary. For this section of the fence we connect with metal corners on racks and weld them.

Welded mesh fence - photo

If instead of sections a canvas is used, the edges of the two rolls should be attached to each other, one extreme wire should be removed and the edges of the canvases should be connected with it, forming a single monolithic one. After that, we unfold the grid and fix it on the racks with brackets or clamps.