Nozzle on a drill for cutting metal: an affordable tool. Types and application of nozzles for a drill for cutting metal Video: Nozzle-scissors for cutting "Cricket"

There are many ways to process metal products, both industrially and manually; are used for this various tools, including a nozzle for a drill for cutting metal.

In contact with

Types of processing

Once upon a time, the only possibility of processing metal products was, but with the development technical progress man invented new ways, and now we have a fairly rich selection of such means.

All of them can be divided into two main groups:

• thermal;
• mechanical.

Each method has its own advantages, and each requires its own toolkit.

Cut while it's hot

In thermal cutting, the cut is made using high temperatures. The following types of such processing are known:

1. Gas.
2. Gas-electric.
3. Plasma.

Gas causes cutting by burning in oxygen, directed in the form of a jet to the site of the intended cut. Melting does not occur - the material retains its hardness, so that the cut is even.

There are also oxygen-flux and oxygen-lance options. In the first case, a flux additive is supplied to the cut site along with oxygen, which has a chemical, thermal or abrasive effect on the material, which facilitates the cutting process. With the oxygen-spear variety, the necessary temperature parameters are provided by the combustion of a steel tube through which oxygen passes.

The gas-electric method involves the use of electricity and includes two types of cutting:

• air-arc - the melt is removed by an air jet supplied under high pressure;
• oxygen-arc, when metal splashes from an electrically heated material burn in an oxygen jet, and the scale is blown away from the cut.

Gas techniques are inexpensive, relatively easy to use, but do not provide a high quality result: after them, additional processing of the cut edges is required.

Plasma processing is carried out using a plasma torch, which creates a plasma jet with heating from 5000 to 30000 degrees. The latter method has several advantages over the previously mentioned ones:

1. The versatility of the application of the technique.
2. High cutting speed and precision.
3. Possibility of cutting along a complex curved contour.
4. More high level environmental safety.

The disadvantages of this method include the high cost of equipment and the complexity of its maintenance, the noise of the process, the impossibility of processing large-sized products with a thickness of more than 8-10 cm.

Important! when carrying out heat treatment, it is necessary to observe safety precautions, protecting the face and hands from sparks and hot splashes.

Harder than iron

The mechanical version is much more accessible than the thermal one in everyday life and involves processing with tools that have a higher hardness compared to it, the use of which requires quite significant physical effort.

It can be:

1. Scissors.
2. Accessories for an electric drill.

When cutting metal sheets, the first type of tool is usually used. known the following types scissors:

• cutting shears for metal manual;
• slotted, powered by an electric motor;
• guillotine - manual and mechanical type.

The guillotine type is equipped with a single oblique blade moving in the same plane at an angle, so you can work with less force than when working with conventional roofing scissors.

Saws have an electric drive and are divided into:

• saber;
• disk;
• angle grinders.

Saber equipped with a kit saw blades length from 100 to 300 mm, moving along a reciprocating path. When working with them, you need a good eye.

cutting part circular saw is a disk, the diameter of which primarily determines what type of work can be performed with its help - the larger it is, the more diverse they are.

1. TurboShear MALCO TSCM EV - used for profiled sheets up to 0.6 mm thick. Telescopic clamp and shank provide a secure fit. Lightweight body - aluminum, knives - high-strength steel. Design features provide the ability to rotate to any angle.
2. TurboShear (punching) MALCO TSMD EV - suitable for cutting metal products up to 1.2 mm and cutting corners up to 90 degrees. Provides a perfectly even cutting line on both sides.
3. Black & Decker MTS04 - designed for grinding. Also this nozzle on a drill is suitable for cutting, a tree, plastic. The tool is intended to be used for repair and construction works ah at home.
4. TurboShear MALCO TS1 EV - involves cutting steel sheets up to 1 mm thick. Fastening provides a shank. The body is aluminium. Blades made of carbon steel. This part can only be operated with both hands.
5. Scissors NP 1,8 SPARKY 181874 - suitable for electric drills of any model. Able to perform linear and radius cuts, allows you to cut unalloyed steel.

Useful video: nozzle for a drill for cutting metal

The use of the above devices allows you to significantly expand the scope of the tool, making it universal. However, it cannot completely replace saws, scissors and a grinder.

Thanks to great choice With a variety of drill bits, this versatile tool can replace many other tools. For example, grinding discs eliminates the need to purchase grinder, and a nozzle for tightening screws and self-tapping screws will replace a screwdriver.

With these tools, you can do the following:

• grinding;
• polishing;
• cutting;
• mixing;
• twisting;
• drilling holes of different diameters;
• milling.

At correct use the result will be of the same quality as if the work was done with a special single-purpose tool. you can’t do without a drill with different nozzles at, a pigsty, cages for rabbits and other outbuildings in the country.

Types of nozzles

All nozzles for drills are divided by purpose:

• stops;
• for drilling holes, crowns;
• cutting, nozzle-scissors "Steel beaver" and "Cricket";
• for drilling at an angle;
• polishing and grinding;
• cutters for wood and metal;
• removable;
• sharpening.

The parallel stop is used to adjust the insertion depth of the drill, there are also special bottom drilling stands reliable fastening tool. In addition to the standard drilling function, blind holes can be made with a drill, for example, for installing hinges in wooden furniture. In this case, a Forstner drill is used. The base of the hole is flat, and its edges are absolutely smooth. Or they use feather drills instead.

Cutting attachments

Unlike a grinder, drill bits for cutting metals work more delicately and do not deform the coating of the material being processed. The tool is driven by the chuck of the tool on which it is installed.

For cutting metals, you should choose drill models with a speed of at least 2800 rpm.

Benefits of cutting attachments:

• even cut;
• comfortable work;
• easy to use and maintain, no adjustment required.

The attachment for the Cricket drill is a nibbler with two cutting heads. They are used for cutting thin sheet metal: profiled metal sheets, metal tiles, profiled or sheet plastic as well as polycarbonate. "Cricket" is simply irreplaceable when erecting on a site.

"Cricket" is used for sheets of materials with the following parameters:

• the thickness of sheet steel should not be more than 1.5 mm;
• stainless steel up to 1.2 mm;
• aluminum, copper and plastic no more than 2 mm.

The cut after processing this nozzle always remains smooth, without notches, and the coating is intact.

To make a high-quality and even internal cut, you must first drill a hole.

The nozzle matrix rotates, thanks to which it can work with both horizontal and vertical surfaces. The recommended number of revolutions of the tool to use this tool is 3000 rpm, the minimum is 1500 rpm.

Also, for cutting profiled sheet metal and tiles, the Steel Beaver scissor attachment is used.

The principle of operation is similar to the previous nozzle, the cut occurs due to the frequent reciprocating movements of the punch, which bends the material and breaks it against the matrix. This tool can make curved and straight cuts. The minimum cutting radius is 1.2 cm. You can work with it at any angle (360 °). Compared to the Cricket, the rig is capable of cutting steel sheet thicker - 1.8 mm. The main advantage of the nozzle is a smooth cut, and due to the absence of sparks, it does not deform during operation. protective covering material.

At the end of work, you should carefully handle the sheet material, since the cut edge after processing becomes sharp.

Attachments for grinding and polishing

With the help of nozzles on a drill for grinding and polishing, you can carry out the following types of work:

• polishing metal, wood coatings, as well as glass surfaces;
• grinding of metal, details from it and other materials;
• removal of corrosion, scale, chipping and old coatings;
• glass edge grinding.

Compared to special tools, these devices are inexpensive and can handle large quantity different tasks, I make any surface perfectly flat and smooth. In addition, they can be processed hard-to-reach places where other tools cannot be used. But due to not large sizes it is difficult for them to carry out a large amount of work.

When purchasing a nozzle for a drill for processing wood or other material, you should carefully study the instructions. Since for different types rigging required different power and the number of revolutions of the tool.

All polishing and grinding attachments are a rod on which grinding material is fixed, such as foam rubber, felt, brushes or sandpaper.

The following types are produced:

• plate;
• disk;
• fan;
• drum;
• end;
• cup.

Polishing devices are divided not only by the type of construction, but also by the degree of hardness: hard, soft, super soft, embossed.

Cup

A cup attachment for a drill for grinding wood or other coatings consists of a rod for fixing in a cartridge, and a cup-shaped body filled with hard or light bristles. Most often it is used to remove corrosion or old coatings. Models with a soft polishing part are also available: foam rubber, felt or other similar material. The body is made of durable and lightweight plastic or metal. Soft nozzles on a drill are most often used for car polishing.

Disc and platter

Disc devices, like cup ones, consist of a rod, a body and a grinding material. The main difference from the previous model is the direction of the bristles (steel wire, brass brush), it is directed from the center to the edges of the disc. You need to use them carefully, as you can quickly ruin the coating.

Plate attachments for polishing or grinding drills are made according to the same principle as for grinding devices. But instead of a thread, they are equipped with a movable or fixed rod for fixing in the cartridge. Sandpaper is attached to them with Velcro.

Experts recommend purchasing plate nozzles with a moving rod, rubber or with a soft and thick layer between Velcro and the base. Since then you can adjust the angle of the drill and smoothly follow the contours of the material.

When working with a rigid cymbal, it is more difficult to control, and even with a slight tilt, it will make a noticeable indentation in the surface. As a result, you can completely spoil the material. Therefore, they are recommended to be used only with a firmly fixed instrument on the rack.

Fan (petal), drum and end

Grinding fan nozzles on a drill are small disc in the center, to the edges of which the petals of sandpaper or other abrasive material are fixed. It is convenient to handle hard-to-reach places, internal cavities or grind holes with such a device, as it is able to take any shape. They are fixed in the drill chuck in the same way as previous models, using a rod.

Drums are made in the form of a cylinder with a rod, covered on the outside with sandpaper. Unlike a poppet attachment on a drill, the processing surface is parallel to the chuck, and not perpendicular. They process wood, metal, glass. Most often used for sharpening the end of glass. They are soft and hard, depending on the purpose of the appointment.

The end ones are a rod, at the end of which the processing material is fixed in the form of a circle or cone. Nozzles work on the principle of a file. Using them, you can increase the diameter of the hole, as well as remove notches and make the edges smooth.

Other nozzles

An angled drill attachment allows you to make holes in places where it is impossible to work normally. The angle can be adjusted or be fixed - 90 °. Drill bits are used for drilling in wood, concrete, ceramic and tiles, metal and other materials of large holes. They are made of high quality steel so that the holes are smooth, without chips and cracks.

The nozzle for sharpening drills is a body with a leash and grindstone inside. Sharpening holes are different diameters. Their number can reach 15 pieces. Mixer attachments are used for mixing various mortars, paints and other mixtures. Selected depending on the consistency. There is also a special nozzle for tightening self-tapping screws or screws, but it should be purchased for drills equipped with a speed reduction function.

For bird owners, a pen-removable attachment for a drill for plucking birds has been developed. It instantly and safely removes all feathers from the carcass. In this case, the skin and meat are not damaged. Before work, it is not necessary to pre-scald the carcass or process it after plucking with a blowtorch.

The nozzle on the drill for plucking birds is easy to use, you just need to fasten the tool with high quality and bring the bird to it. It is made from easily washed materials and takes up very little space.

For those who work with wood material, nozzles cutters of different types are issued. They allow you to make grooves various forms, machine holes or remove defects. They are pointed and backed.

Before working with any nozzles, you should check the reliability of their fastening in the chuck and the material being processed. The drill must be held with both hands. Be sure to use protective equipment (gloves, goggles) while working.

Homemade nozzles for a drill - video

Almost every specialist involved in construction and repair work faces the need to cut any metal products. Many professionals for high-quality metal cutting use the most different instruments, starting with a cutter, grinder and ending with hand scissors. But what to do if at the right time there are no such tools at hand, and it is extremely necessary to cut the metal. This process can be carried out using a conventional electric drill. Right now in construction stores for these purposes, you can purchase specialized nozzles for a drill for cutting metal.

What is a metal cutting drill bit?

By their own design features the nozzle resembles a punch or a cotter pin, which, due to the matrix, breaks through the metal with a large number of repeated movements. After that, strips are formed in the workpiece required form. In the process of cutting, the effect on the metal occurs in a pointwise manner, which helps to preserve the integrity of the products as much as possible. A similar nozzle repeats the work.

With the help of a nozzle, you can process metal, the following parameters:

• aluminum with a thickness of products on average up to 2 mm;
• stainless steel up to 0.8 mm;
• brass, copper, galvanized steel, iron sheets, zinc with a thickness of up to 1.5 mm.

It should be remembered that the softer the material being processed, the greater its thickness can be.

Features of the nozzle

Before direct work, the nozzle is securely fixed in the drill (chuck), which drives it. The principle of operation is almost completely identical to the process of operation of electromechanical scissors, which perform straight and curly cuts without much difficulty. To ensure a high quality cut, you should correctly select the number of revolutions. For example, for a metal of small thickness, from 2700 to 3000 thousand revolutions is well suited. Start cutting only when the drill has dialed required level revolutions.

Typical types of nozzles for a drill

On the market you can find several models of nozzles for metal drills:

• nozzle "cricket"(acts like nibblers) - used for cutting thin sheet metal. Consists of two special cutting heads. The cricket nozzle is often indispensable in the implementation roofing works. For example, such as cutting metal tiles or corrugated board. Using such a nozzle allows you not to deform the material and get even and beautiful cuts. In contrast to cutting with a grinder, the nozzle is able to perform sharper, burr-free edges. With the help of "cricket" you can also drill neat round holes large diameters, including artistic cuts. If necessary, work can be carried out on horizontal and vertical surfaces. As additional criterion the cricket nozzle helps to process the edges with special abrasive materials during the cut. The price of such an instrument is often in the range of 4000-7000 rubles;

• nozzle "steel beaver"- for the most part, this type of nozzle is used when cutting profile and flat sheets metal. According to its principle of operation, the cutting mechanism of the nozzle itself very much resembles the processing of material using punching shears or a “guillotine”. In addition, using the nozzle "steel beaver" in the process of work, the protective layers of the metal coating of the sheets are not burned, and thus no sparks are formed. The use of a nozzle eliminates the risk of possible chips or deformation of the cut edges. This attachment can cut polycarbonate, aluminum or plastic. Distinctive characteristics nozzles are: drill rotation from 1500 to 3000 thousand revolutions, minimum cut radius - 12 mm, the ability to change the cutting angle of 360 degrees, the processed thickness of materials - copper and aluminum 2 mm, stainless steel - no more than 1.2 mm, ordinary steel - up to 1.8 mm.

There are many variations of this tool from different manufacturers However, the principle of operation is the same for all.

The main advantages of nozzles

As a rule, experts identify several main advantageous differences between nozzles for a drill and a grinder:

• tool versatility;
• simplicity in after-sales service and application;
• high quality cut;
• good performance;
• the ability to make holes of any shape;
• cost savings due to the absence of the need for additional Supplies in work;
• ease of use of the equipment, achieved by equipping with a special handle;
• the ability to work from a pneumatic or electric drill.

It should also not be forgotten that certain skills are required to ensure a high quality cut. Of course, unlike household or professional tools complex configuration, to work with the nozzle will not have to adapt for a long time. Any beginner will be able to cut through up to 10 meters of metal in 1 hour. The attachment can be attached to any type of modern drill.

In general, you should not think that a drill attachment for cutting metal will be a full-fledged replacement for several tools at the same time. Unfortunately, the power of this equipment is not always enough in comparison with electric scissors. professional level. In addition, the supported thickness of 1.5 mm does not make it possible to carry out any really serious work.

If you do not take into account the degree of productivity of the tool, then the nozzle can be completely purchased to perform not too resource-intensive work. In such situations, the nozzle will significantly save a lot of time and money.

For repair and construction work, it is necessary to periodically cut the metal. It is not always possible or expedient to purchase special expensive equipment. In such cases, a nozzle on a drill for cutting metal can help out.

Special equipment for metal cutting

In production and construction, it is necessary to regularly cut metal sheets, cut holes, cutouts in them different shapes.

Many types of tools and equipment can handle such tasks:

• . She is Bulgarian. Using special trimming wheels, it is possible to cut sheet metal, reinforcement. Often used for this very purpose. But there are drawbacks. Burrs remain on long cuts, not suitable for corrugated board, as it damages polymer coating, requires the constant purchase of cutting discs, which wear out quickly.
• Guillotine. Performs cutting of rolled metal with a fairly wide range of thicknesses. Has high performance. They are mainly used only in enterprises due to the high cost of equipment.
• A circular saw. It is possible to cut metal at different angles and with high precision. It is not possible to perform complex cuts, after working with it there is a lot of waste.
• Jigsaw. Allows you to cut the material at different angles. Suitable for cutting sheet metal.
• Metal shears. There are different kinds. For sheet steel - intended only for simple cutting of metal. Punching shears - in addition to straight and shaped cutting, it makes a variety of holes. Slotted scissors - do an excellent job with curly cutting, most accurately and accurately perform their task. The disadvantage of such tools is their rather high cost. Suitable for those who are professionally engaged in construction and repair. For one-time work and small volumes, the purchase of electric scissors is impractical.
• Nozzles for drills for cutting metal. There are two types - "cricket" and "steel beaver". According to the principle of operation, they are similar to cutting electric scissors, but several times cheaper in cost.

Nozzle on a drill "steel beaver"

There are undeniable advantages of using a drill for cutting rolled metal. Every master has this tool - both a professional builder and a summer resident.

Drill - universal equipment thanks to the possibility of changing nozzles. They can be for drilling holes, grinding, milling, sharpening, etc.

The design of the nozzles on the drill

Structurally, the “cricket” nozzle is a punch with a matrix. The drill with its rotation informs the punch reciprocating motion. And two cutting heads accurately cut sheets of metal, punching them pointwise.

In the treated surface, cuts with a width of just over three millimeters are obtained. Thanks to such small cuts, the edges of the material remain as even as possible, without burrs. Since the nozzle does not heat up during operation, the protective and polymer coating of the cut parts is not damaged.

"Cricket" is great for working with sheet metal, polycarbonate or other similar roofing materials, including metal tiles. With this nozzle, it is possible not only to smooth the edge, but also to make holes (for example, for a chimney), to make artistic cuts. According to the principle of operation, these are cutting scissors.

The nozzle can cut sheet material with the following thickness parameters:

• polycarbonate (plastic) up to 2 mm;
• stainless steel up to 0.8 mm;
• aluminum up to 2 mm;
• zinc, iron, brass, galvanized steel up to 1.5 mm.

The nozzle for cutting metal is screwed to a drill or a screwdriver, clamped with the same nuts as the bits. The tool can be held at any angle, which makes it much easier to work with it. And also makes it possible to perform actions in any planes, which is indispensable for the installation of the roof.

Metal cutting attachment

The nuances of using "cricket"

The choice of "cricket" is determined by a lot of advantages:

• Neat cut. Unlike a grinder, a drill attachment will not leave burrs on metal surface and will not damage the polymer coating of the material with sparks.
• The lightness of the tool. There is no need to put in a lot of effort.
• Drill and screwdriver compatible. There is no need to purchase an extra tool.
• Price. It is much cheaper than special equipment for cutting rolled metal, and it also saves money on the purchase of consumables such as cutting discs for a grinder.
• Easy to use. Easily installed on the cartridge, and also easily removed.
• Performance. With the help of the "cricket" you can quickly cut the material.
• Convenience. Thanks to its shape, it allows you to hold the tool at any angle.
• Ability to cut holes and cuts of any shape.
• Versatility. Suitable not only for flat sheets of metal, but also for profiled ones.

And yet, certain nuances of working with a nozzle exist. The instrument must be held with both hands. That is, the material being cut must either be securely fixed, or the master must work with an assistant.

Like any tool, it takes skill. If you work with him for the first time, then it is better to practice first. For effective work nozzles, the rotation speed of the drill should be 1500–3000 rpm. But when buying a "cricket", you still need to clarify its characteristics and requirements - for some, the minimum cartridge rotation speed is 2700 rpm.

The "steel beaver" is similar in design and principle of operation to the "cricket". It also does a good job of cutting sheet metal. Curvilinear cuts are made with a minimum radius of up to 12 mm. The difference is that the metal can be thicker - stainless steel up to 1.2 mm.

And also you need to take into account that when working with these nozzles, a lot of metal chips are formed.

Safety

Regardless of the brand of drill and nozzle, their prices and characteristics, it is very important to observe safety precautions.

This will prevent injury and damage to the material.

• Wear protective goggles and gloves when operating the drill.
• Before starting work, it is important to check the fastening of the nozzle.
• Be sure to check whether the material to be cut is well fixed.
• The drill must be held with two hands for special holders.
• When working with a metal cutting attachment, constantly remove falling chips. For example, when installing a roof a large number of shavings can damage the surface of the metal tile.
• At the end of the work, for some time you should not touch the treated metal with your hands and remove the nozzles, as they can heat up due to friction.

So, when we cut metal sheets up to 2 mm thick, for example, when installing a metal tile or a corrugated fence, and the amount of work is small or one-time, it makes sense to pay attention to drill nozzles.

Video: Nozzle-scissors for cutting "Cricket"

When performing construction or repair work, it often becomes necessary to cut a metal blank. To do this, use special equipment in the form of a cutter, grinder or. However, it is not always available. You can cope with the task with the help of a nozzle on a drill for cutting metal, which will cut products of small thickness.

Many craftsmen are accustomed to using a drill for its intended purpose, namely for drilling holes. But not everyone knows that this tool can be turned into a multifunctional device, supplementing it with special nozzles, fixtures and stands, which will make the drill universal and indispensable in any job.

With the help of special nozzles for a drill, which can be bought at any specialized store for affordable price, can carry out drilling of holes of various diameters, cutting, grinding, polishing, twisting, mixing and milling. There is also a pump attachment for a drill, designed to pump fluid. The attachment for plucking chickens is simply indispensable in household. With the correct and competent use of additional prefixes, the result will not be the worst quality, as well as when using a special single-purpose device, but the cost of such a universal tool will be several times lower.

By purpose, all existing nozzles are divided into:

• equipment for drilling holes and crowns;
• scissors for cutting metal;
• stops;
• corner fixtures;
• grinding and polishing nozzles;
• equipment for milling wood and metal;
• sharpening devices;
• transfer nozzles.

When working with any nozzle on a drill, you must follow the safety rules:

• the equipment must be securely fixed in the tool chuck;
• the drill must be held with two hands, which is especially important for powerful models;
• constantly adjust the pressure of the tool;
• work in personal protective equipment;
• after completion of work, do not touch the drill for several minutes to avoid burns.

What are drill bits for metal cutting?

Equipped with a special nozzle for cutting metal conventional drill turns into a punch or cotter pin. Device punches metal product due to the implementation of numerous reciprocating movements along the internal cavity of the matrix. As a result, an even cut line 3.1 mm wide is formed with the protective layer on the surface of the metal sheet preserved.

Important! The maximum efficiency of the nozzle is achieved only when used in conjunction with electric drill, the rotational speed of the cartridge of which is at least 2700 rpm.

The metal nozzle on the drill can handle the cutting of such metal products:

• aluminum, up to 2 mm thick;
• made of brass, copper, zinc, galvanized steel and sheet iron, up to 1.5 mm thick;
• made of stainless steel, up to 0.8 mm thick.

Using a drill bit for metal cutting has a number of advantages:

• the cut is of high quality;
• there is no need to constantly purchase consumables, which saves money;
• ensured high performance when cutting metal;
• versatility of the device;
• the equipment is convenient and easy to use and maintain;
• the nozzle can be used for electric and pneumatic drills;
• with the help of a nozzle it is possible to carry out cuts of any configuration.

Despite all the advantages listed above, in order to get a high-quality cut, some skills and dexterity are required to work.

Popular nozzle models

Today, there are a large number of different models of drill bits, thanks to which you can not only cut metal in a straight line, but also do curly cuts. This is required for installation. ventilation ducts, roof structures, gutters. Using the nozzle allows you to cut in any spatial position without making any preliminary adjustments.

Nozzle types:

• cutting nozzle "Steel beaver" is used for cutting metal tiles, corrugated board and any flat profile sheets;
• universal nozzle "Cricket" is used for cutting profile metal, polycarbonate and plastic;
• special nozzles for curly and curved cuts are represented by the EDMA Nibbek, ACRO YT-160 A, Sparky NP 1.8 L models, which differ in the thickness of the processed sheet.

Nozzle-scissors on a drill"Steel Beaver"

The classic drill attachment for cutting metal tiles and any flat sheets of metal in the form of a freely rotating shaft in a bearing with a fixed eccentric works on the principle of a crank mechanism with the difference that energy is supplied here for rotation.

A complete cutting tool support part located on the frame, and movable - connected to the eccentric. It is the movable part that performs reciprocating movements during the rotation of the shaft. A mandatory element of the design is the handle, which is fixed perpendicular to the axis of rotation of the spindle. During the increase in load, a reactive torque occurs, due to which the drill advances relative to the nozzle.

It should be remembered that the tool must be placed strictly vertically relative to the workpiece when making a cut. Failure to do so may result in damage to the product and injury to the operator.

The device resembles metal scissors. The drill attachment is used for cutting flat products or profiled sheets with large radius bends. The cutting line is easily controlled. When the tool is running protective layer coating is not burned, which eliminates the formation of sparks and the likelihood of burrs. You can perform continuous cutting of products of any length. You can buy a drill attachment for cutting metal tiles and flat metal sheets for 1600 rubles.

Using the “Steel Beaver” nozzle for a drill, you can make a figured cutout for mounting roof ventilation elements or a gutter

Sheet cutting is performed at a drill speed of 1500-3000 rpm. The cutting angle is 360 degrees, the minimum radius is 12 mm. With the help of the “Steel Beaver” nozzle, you can cut:

• copper or aluminum sheet 2 mm thick;
• steel - no more than 1.8 mm;
• stainless steel - up to 1.2 mm,

Useful advice! For cutting a profiled sheet with bends of small diameter, use cutting shears of the Cricket type.

Nozzle on the drill "Cricket"

Nibblers "Cricket" got its name due to the characteristic noise during operation of the device. The nozzle is similar to the previous model, but has a different design of the working element, consisting of two cutting heads. The principle of operation of the nozzle "Cricket" is similar to an office hole punch. Accurate holes are squeezed out in the metal during oscillatory movements of the cylindrical striker with a high frequency. Thanks to translational movements along the marked line, it is possible to obtain an even cut.

Nozzle-scissors "Cricket" are used for cutting metal thin and profile sheets, and polymeric thin-sheet products up to 2 mm thick. Work can be performed in the horizontal and vertical plane. Due to the ability of the tool to rotate 360 ​​degrees. you can drill large round holes and make artistic cuts. You can buy a nozzle for a drill for cutting metal "Cricket" for an average of 1500-4000 rubles.

The tool can cut metal with stiffeners and various profile stampings in two ways. The first option involves repeating the surface of the profile, bending around the edges. It is used for products with an average bending radius. For cutting metal tiles, another cutting option is used, according to which the tool moves along the stiffeners without bending around the sheet profile.

Before you buy a nozzle for a Cricket drill, you should consider the main drawback of the tool. Due to the fact that the nozzle punch has a diameter of several millimeters, when cutting the product, a cut of a certain width is formed, which leads to certain material costs. The result is crescent-shaped metal chips with sharp edges, which should be disposed of immediately for safety reasons.

Useful advice! When working with the tool, do not wear soft shoes.

Nozzle for drill "Cricket" does not require adjustment, easy to use and maintain

One of the most popular models is the “Cricket” scissor attachment for metal up to 1.6 mm Enkor 14210. The tool is able to cut thick enough a metal sheet in a straight or curved direction. You can buy a nozzle for a drill for cutting metal for 1300 rubles. Main Feature tooling is that during the cutting process a path is formed with a width of only 1.6 mm, which provides enough good level material savings.

The device can be installed not only on a drill, but also on a screwdriver. The metal cutting attachment is lightweight, which does not add weight electrical appliance. The kit includes a replaceable handle, which increases the accuracy of the work. The device has a low noise level due to its special design, which makes working with it more comfortable.

Nozzle on a drill for sharpening drills

This device consists of a plastic case, inside which a special-shaped emery wheel rotates. It is he who allows you to form the required sharpening angle on the working part of the tool. The circle is mounted on a shaft, which is connected to the drill with a special coupling. It is activated when the tool is turned on.

Many modern models have an end cover on the body, in which there are holes of various diameters for sharpening drills different sizes. These holes are made in such a way that the element for sharpening is in contact with the emery wheel in a certain position.

The principle of operation of the sharpening nozzle is simple - when the drill is turned on, the chuck rotates the whetstone located inside

The process of sharpening the drill is as follows. The product is inserted with the cutting part into the nozzle hole of the corresponding diameter. After starting the drill, the emery wheel begins to rotate, sharpening half of the drill bit. Then the product is turned over in the hole by 180 degrees, and the procedure is repeated. This sequence of actions is performed several times until the required parameters of the cutting part of the drill are reached.

A drill attachment for sharpening drills, which you can buy on average for 350-500 rubles, has 15 holes with diameters from 3.5 to 10 mm. Products can be sharpened at an angle of 180 degrees thanks to special form stone. Simple design device allows you to perform work quickly and without special skills.

Related article:

Types of structures, their characteristics and features. Review the best manufacturers machine tools. Comparative characteristics rates.

However, it should be remembered that the device is intended for sharpening cutting edges. For a full-fledged sharpening of heavily worn products, an emery wheel will not be enough for a long time.

Useful advice! Buying a nozzle specific model, consider the diameter of the drill chuck.

There is also another type of additive. This is a nozzle for a drill for sharpening knives and scissors, which is presented in the form of two emery wheels planted on a shaft and located at a certain distance from each other. The price of such a device is about 250 rubles.

The nozzle for and scissors for a drill is easy to operate, does not require special skills in its use.

Nozzle for a drill for grinding

Using a grinding attachment on a drill, old coatings, corrosion, nicks, scales are removed from the surface of the product. It is used for grinding glass edges, metal parts and products from other materials. Due to the small size of the equipment, hard-to-reach areas can be processed. average cost products is 500 rubles.

Grinding drill attachments are used for preliminary rough preparation of the base for future polishing. It is made in the form of a rod, on which grinding material is fixed in the form of a brush or sandpaper. There are various types of such devices that are used for specific tasks.

A cup attachment for a drill for grinding wood or other material is represented by a rod mounted on a chuck and a cup-shaped body filled with light or hard bristles. The body is made of metal or durable and lightweight plastic. Usually such a nozzle is used to remove old coating or corrosion from the surface.

Another variation is the disc attachment for a metal grinder, where the bristles of the grinding material in the form of a brass brush or steel wire are directed towards the edges of the disc from its center. This additive should be used very carefully, as it can easily damage the coating. The plate nozzle has a movable or fixed rod, which is fixed on the cartridge. Sandpaper is attached to it with Velcro.

Useful advice! It is better to purchase nozzles with a movable rod, which allows you to adjust the angle of the drill, while smoothly following the contours of the material.

Petal or fan grinding head represented by a rod on which pieces are fixed sandpaper or other abrasive material. It is used to perform radius grinding or surface treatment with complex profile. It can also be used for grinding holes, as well as carbide cutters or cutters that work on the principle of a file.

Grinding abrasive stones, mounted on the stem, are used to remove sagging, burrs, boring holes or leveling the weld.

Drill bits for polishing

After grinding the base, it is necessary to give it a smooth surface. This is done by polishing using special nozzles. They can be made from felt, wool, foam or felt. According to the degree of softness, they can be hard, soft, super soft and embossed. According to the method of fastening, nozzles with a stem, with Velcro and with a holder-lock are distinguished. Fan or disk nozzles are used for polishing discs, end devices are used for holes. The average price of a product is 250-300 rubles.

Many motorists have in their arsenal a nozzle for a drill for polishing a car. However, when choosing this product, you should consider some features:

• the device must be of high quality and professional;
• for efficient and safe polishing procedures maximum amount the speed of the drill should not exceed 3000 rpm, which is indicated in the characteristics of the device, otherwise the paint will simply burn out;
• the nozzle must be from a well-known brand;
• the device should not be included in the budget products;
• for polishing each individual part of the car should be used special nozzle designed specifically for this purpose.

The process of polishing a car with a drill is a very complex and time-consuming process that requires certain skills. If there is no experience, first you need to study all the subtleties this process, master the basic techniques presented in the videos on the Internet. It is better to start with inconspicuous areas of the body. The tool is configured to the desired parameters, taking into account required number revolutions. The nozzle should not be pressed too hard against the surface to high temperature don't burn the paint.

Nozzle for a drill for plucking birds

Plucking a bird is a very time-consuming process, especially when it is necessary to process several carcasses. Therefore, many farmers were constantly looking for new solutions not only to make work easier, but also to reduce the overall time. For this purpose, a feather attachment for a drill was specially developed, which removes feathers from a bird in a matter of minutes. It is similar to a dishwashing brush, only silicone fingers act as bristles here, which, when the shaft rotates, pull feathers out of the carcass. At the same time, the bird is brought from different sides.

Nozzle for a drill for plucking birds, which you can buy on average for 1500 rubles. processes poultry carcasses in just 2-3 minutes, leaving not a single feather. The result is smooth, undamaged skin. The device is effective not only for processing chickens, but also gives a good result when plucking geese. The drill attachment can be used not only for fresh, but also for frozen poultry.

Useful advice! It is not recommended to scald the carcass with boiling water before using the nozzle, which will reduce the efficiency of the processing process.

The main advantages of the drill attachment, which you can buy at any specialized store, are the speed, ease and portability of use, which does not require certain skills and additional processing of the carcass before plucking. A significant disadvantage of the device is that after this mechanical process, damage remains on the carcass, which worsens it. appearance. Therefore, if the bird is intended for sale, it should be plucked manually.

Other types of nozzles

When it is not possible to make a hole in the usual mode, you need to use an angled nozzle for a drill. The working head of such a device can be rotated at different angles relative to the axis of rotation of the drill chuck. The main disadvantage of the equipment is the increased risk of drill failure. Therefore, the most popular is angle nozzle for a 90 degree drill, which is fixed on the neck of the drill. The price of the product is an average of 800 rubles.

For craftsmen who are engaged in the manufacture of furniture, cutter bits are very popular. various kinds. They can be backed and pointed. With their help, you can make grooves of various shapes and depths, process holes and remove defects. The cost of equipment is in the range of 350-450 rubles.

To mix a solution of different consistency, a mixer nozzle for a drill is used, which is selected taking into account the density of the solution. So for mixing glue, liquid putties and other fluid mixtures, spiral devices are used that prevent splashing of the solution. For mixing concrete, nozzles with a tail in the form of a hexagon are used. Mixing mixtures with this nozzle will be carried out quickly and efficiently. However, in order not to reduce the efficiency of the device, it is necessary to maintain the volume of the mixture for kneading. The price of the nozzle is 500 rubles.

Useful advice! When choosing a mixer attachment for a drill, it is necessary to take into account the power of the tool. An increase in load can lead to burnout of the winding.

Indispensable in concreting is a vibrator for concrete on a drill, the price of which is about 900 rubles. It is used to compact the concrete mass during its laying, namely, it is designed to remove bubbles and air layers from fresh concrete. The nozzle requires a drill with a power of at least 1500 watts.

For woodworking home master you just can’t do without a nozzle on a drill for cutting wood, average price which is 2000 rubles. To pump liquid, you can use a nozzle-pump.

A wide selection of different attachments, fixtures and accessories makes the drill universal tool, which is indispensable when performing repair work and for other business needs living conditions. It's simple and optimal solution, which will avoid the purchase of expensive specialized power tools.