How to sheathe the front door with dermantine with your own hands. Do-it-yourself upholstery of doors with dermantine: video and photo. Sheathing iron sheet

Additional advantages of leatherette-covered doors are improved sound and heat insulation.

The appearance of entrance and interior doors, even with good care deteriorates markedly during use. If the product is still durable and can last a long time, then fix it aesthetic properties upholstery of doors with dermantine will help. This one a long time ago famous variant finishes door leaf has additional advantages in the form of increased sound and heat insulation.

Dermantin has a rich color range

What special qualities does the material have that allow the door to be trimmed with leatherette, both street and interior structures? Indeed, the list positive qualities dermatina looks impressive:

• Humidity resistance. street door, upholstered in leatherette, you will not have to suffer from rain: water drops easily roll off the surface of the material. With the same success, its waterproofing properties keep the insulation layer intact.
• Immunity to ultraviolet radiation. While most paints and varnishes fade mercilessly under the sun, leatherette retains its decorative qualities unchanged.
• Frost-resistant properties protect door upholstery from deformation.
• Resistance to harmful microflora. Sheathing dermantin is not subject to rot, mold, or mites.
• Neutral attitude towards chemical cleaners. If the front door upholstery is heavily soiled with leatherette, it can be cleaned with any means.
• Big variety colors. The material is presented in such a wide range of shades that it will not be difficult not to choose an option that is in harmony with the interior.
• Durability. Their operational properties dermatin retains for 7-10 years.
• Affordable price is not the most important, but still a pleasant fact that only increases the popularity of the material.

When all are listed positive properties upholstery material, it would be dishonest to remain silent about its shortcomings. Although they are few, they are still there:

• Relatively low strength. It cannot be said that leatherette needs very careful handling, but, by and large, it is a fabric, albeit a very dense one. You can cut it without much effort, and with very rough handling there is a chance to tear the upholstery.
• Problematic repair. Cuts or tears on such a surface cannot be fixed, therefore, if the material is damaged, there is nothing left but to sheathe the door with leatherette again.
• Fire susceptibility. In case of fire, it ignites easily, and since the door is upholstered with leatherette, this can lead to blocking the exit from the burning room.

What to look for when choosing a door upholstery kit

For the upholstery of the door, you need to prepare tools.

The standard set for upholstery of doors consists of leatherette, insulation and decorative nails. How to choose right material to make sure it lasts for a long time?

Leatherette must have high density and have elastic properties. Be sure to pay attention to its smell - if it is sharp, it is possible gross violations technology. Such material may evaporate harmful substances, which means that it is not suitable for interior decoration.

Heaters - isolon, batting, foam rubber. If you choose based on the lowest cost, this is foam rubber. It has a low density, so when finishing decorative trim forms a beautiful pronounced relief. If the insulation must provide heat and sound insulation, isolon is best suited for this task.

Upholstery of an external or interior door with leatherette

Sheathing a door with dermantine with your own hands is not a very difficult task. First you need to prepare the necessary material and tools. This list is compiled depending on how the door will be upholstered. But the required components of the list will be:

• leatherette;
• insulation;
• scissors, sharp construction knife;
• a hammer;
• construction stapler;
• roulette;
• decorative nails.

Traditional door trim

The door leaf is laid on a flat horizontal surface.

First you need to prepare the door leaf. It is removed from the hinges, the fittings are unscrewed, dust is swept away, dirt and grease are cleaned. Before starting the main work, you can immediately prepare the rollers, which will further ensure the insulation of the doorway. For a door that opens into the room, 3 rollers are required, and if outside, then 4. The length of the roller must correspond to the parameters of the part of the door where it will be located, and the width is such that it is possible to lay the insulation roller inside and fold the tape in half lengthwise. For attaching the roller to wooden door It will be convenient to use a construction stapler. On the iron door the roller will have to be glued. Insulation is laid in the same way: the canvas cut to size is glued or shot with staples.

Then comes the turn of leatherette. The method of its installation depends on the door.

• Metal doors need glue. First, it is evenly distributed with a brush along the perimeter of the door leaf and a lining is glued to this line, on top of which new layer glue is laid leatherette.
• Leatherette is attached to a wooden door with a decorative nail.

The final stage of work includes the installation of fittings.

A special way for the lazy

Covering the door with leatherette, without removing the door from the hinges.

This method is called so because the upholstery of the door with dermantine is carried out without removing the door from the hinges. This is especially convenient if the weight of the door is large, which makes it difficult to remove. At the same time, sheathing the door with leatherette on weight is a very inconvenient task.

The beginning of work looks the same as in the previous case: the fittings are removed from the door and cleaned. Then the roller is mounted: the prepared leatherette tape is laid along the edge of the door leaf and fixed with a construction stapler or nails every 15 cm. At the next stage, a sheet of foam rubber is shot with a stapler. The leatherette sheet should have reserves of 3 cm on all sides. They begin to fasten it from the center line of the top of the door. Carefully stretching, it is nailed around the entire perimeter. Now it's the turn to return to the formation of rollers, the blanks for which we had nailed at the very beginning. To do this, roll up a long roller, lay it along the edge of the door leaf, wrap a strip of leatherette and, twisting the edge inward, nail it with decorative nails every 10 cm. After the fittings are installed, the work is over.

Door upholstery with dermantine using a frame profile

Door trim materials

This method allows you to create almost any, even the most intricate pattern on the upholstery, since the markings for placing decorative nails are made directly on the surface of the door.

The door upholstery kit should include additional details: one-sided frame profile, which will ensure uniform tension of the fabric, and decorative furniture buttons with a top trimmed with leatherette. These buttons are unscrewed into two separate parts, one of which will be on the door leaf, and the second on top of the leatherette.

After dismantling the fittings and cleaning the door leaf, it is necessary to start marking the lines on which the lower elements of the furniture buttons will be located. With the help of a ruler and a square, we determine desired points and generously drip on them mounting adhesive. Glue the threaded button elements to the surface. We measure the sides of the door and cut the profile according to the measurements obtained. We put it on construction glue around the perimeter of the door leaf. Now you have to wait until the glue dries - it will take about a day. In order not to waste time, we are preparing the insulation: we need to prepare the holes for the buttons.

After a day, we continue the upholstery of the door: we lay the insulation in such a way as to align the holes with the threads of the buttons. If there is excess material that protrudes beyond the edges, they must be cut off. Now it's dermantin's turn. We carry out exactly the same procedure. Now, when all the threaded pins are located in their sockets, you can screw on the decorative hats, after which the leatherette, evenly pulling, is tucked into the profile.

This completes the door trim. After installing the fittings, the canvas is hung in a permanent place.

Tiled upholstery method

Door upholstery with chopped leatherette

Thin painstaking work but the result looks amazing. It is made from dermantin cut into rhombuses. As a rule, the door is sheathed in a single color scheme, but this method is good because creative people can experiment and create interesting ornaments on the surface of the door.

For this option, you will have to perform more complex markings on the surface of the door: draw them into diamonds of the same size. In the corner of each rhombus, we put the lower element of the furniture button on the glue and set the door leaf aside for a day. Like last time, we make cuts on the insulation, cut the leatherette into rhombuses a little bigger size than markup. A day later we return to the door. We lay the foam rubber in accordance with the prepared cuts, perform additional fastening with a stapler along the edge and door leaf (3-4 brackets around each pin). We start laying out rhombuses around the perimeter. We bend the edges of the blanks and shoot them with a stapler. It is necessary to ensure that in the process of upholstery on the dermantine there are no distortions.

How to sheathe a door with dermantine so that it is not only durable, but also beautiful? We have offered several options, choose your own, which you can implement, and the result will be stunning.

(detailed video instruction for self-upholstery of the door, see the bottom of the page)

In this guide, we'll show you how to make your own. front door.
For this you will need:
1. Vinyl leather (dermantin, artificial leather, leatherette, PVC film, vinyl artificial leather, leatherette). Viniliskin is sold by cut, the width, as a rule, is in the range from 110 centimeters to 140 centimeters. If you have a standard metal door, then for its upholstery a piece of cloth will be enough, the dimensions of which are 10-15 centimeters larger. If your door is wooden, then you need to take into account that in addition to sheathing the main door leaf, it will be necessary to make rollers, for which strips of leatherette 12-15 centimeters wide are used. In total, we need three strips with a length equal to the height of the door.
2. Lining. For these purposes, you can use foam rubber with a thickness of 10-20 mm. If you need enhanced thermal insulation and then turn your attention to a material such as isolon. This is enough effective material which is used in the automotive industry. Although it is much more expensive than foam rubber, its thermal conductivity properties exceed those of foam rubber by several times. Foam rubber is sold in sheets measuring two meters, which is just right for high-quality door upholstery.
3. . Usually, special furniture nails with a wide head are used. The color scheme consists of shades of gold, silver, bronze and copper. We recommend that you choose the color of the nails that matches the color of the locks and handles. Thus, your door will look quite harmonious. Also in the construction markets you can find nails, the caps of which are tied with vinyl leather. You can choose for yourself nails that match in texture and color with the selected material, or vice versa - play in contrast.
four. . It will be needed if you have an iron door that does not have holes for nails. For our purposes, the “Universal Moment” is well suited. For pasting one side of the upholstery, a 100 ml tube is enough.
5. Tools.
1) Construction stapler and staples with a stem length of 8-10 mm.
2) Hammer.
3) Scissors.
4) Knife (you can use a regular clerical knife with interchangeable blades).
5) Screwdrivers.
6) Pliers.
7) Tassel (for sheathing metal door).
After you have made sure that all of the above items are available, we proceed directly to the process of upholstery of the front door. First of all, it is necessary to dismantle all the locks, peephole and get rid of the old trim (in the event that you need to reupholster the door). Here we will not describe this action, and immediately begin the story about the main thing. It is not at all necessary to remove the door from the hinges, as advised in many similar instructions. So, let's divide our guide into three parts: upholstery of the inside, upholstery outside and pasting of a metal door. But remember: the instruction for upholstery of the door gives only general recommendations and does not take into account the features of a particular door. At some points, you may have to turn on your ingenuity.

How to upholster a wooden door with your own hands

Consider the situation when the door opens into the apartment. In order to beautifully upholster a wooden door yourself, it is advisable to start by making a roller that will visually close the gap between the door frame and the door itself, and in some cases, fit snugly against the frame itself (this depends on the design and profile of the platbands). First, we take one strip of leatherette and use a stapler to nail it with the front side to the door surface so that it goes onto the door by about 3-4 cm. If a padlock is installed on your door, it is better to start nailing the roller from it. If all the locks are mortise, then start upholstering the door from the upper corner of the hinge side. Having thus upholstered the entire perimeter of the door with strips of leatherette, we proceed to laying the foam rubber. First, it must be cut into strips 8-10 cm wide. We fix them with a stapler on the door leaf, turn and nail the material so that the resulting roller protrudes 1-3 cm, depending on the relative location of the door and trim. The roller is ready.

Next, we measure the resulting distance between the inner edges of the roller and cut out the foam rubber, subtracting one centimeter from each side from these dimensions. We fix it with a stapler on the door leaf. The final part remains - to upholster the main surface of the wooden door. We take a piece of dermantine around the corner, tuck the edges by 5-6 cm, lay it in the corner of the door so that the material goes slightly onto the roller and nail a decorative nail with a hammer, stepping back from the edges about 5-7 mm. Then we take the second top corner material, we also tuck it in and, pulling it a little, we hammer in the second nail. Next, you need to check whether the piece of leatherette lay flat relative to the surface of the door leaf. To do this, in the middle of the door, slightly pressing, we draw our hand from the top to the very bottom and, holding it with one hand, with the other we apply the lower corners of the matter to the edges of the door, smoothing them from the center. Accordingly, both on the left and on the right, the distance to the edges of the leatherette should be the same. After making sure that the start is right, we continue the upholstery of the door. We nail the upper edge, making the distance between the nails 10-12 cm. Then we begin to do the same with any side, tucking the artificial leather on equal distance along the entire length and slightly, but not much, pulling it. It is important here not to overtighten, otherwise at the output you will get something like a pleated skirt. Fixing this won't be easy, as you'll have to rip out the already hammered nails, and there's a good chance you'll accidentally damage the upholstery and leave nail marks anyway. Having reached the bottom, proceed to the second side. Lastly, we fix the lower edge of the upholstery material, having previously calculated the future distance between the nails so that it is the same throughout bottom side doors. Everything! The door is upholstered. It remains to install locks and a peephole. Upholstering a wooden door with your own hands is quite difficult for an unprepared person, so many companies offer their own.

How to sheathe the outside of a wooden door yourself

The outer side of the wooden door should be upholstered with leatherette in a slightly different way. First of all, you need to close the door tightly and draw a projection of the door frame on the door leaf itself with a pencil. In other words, draw lines around the entire perimeter with a pencil. The outline of the future door skin will be obtained, and the remaining indentation is needed for the so-called “quarter” of the door. If the door is installed professionally and the locks are properly adjusted, then the door leaf should fit snugly against the frame and, if, during upholstery, we bring dermantine beyond the line, then in the end the door simply will not close. Now we nail the bottom of the insulating roller. We fix it on the door so that in its closed position it fits snugly against the threshold. To do this, we already have a delineated border at the bottom. If the lower roller is nailed to the very threshold, then over time it will rub off from constant touching with your feet. Next, we fix the lining material with an indent from the line of 1 cm. And, similarly to the previous paragraph, we nail the main piece of vinyl leather. Now you need to make a heat-insulating roller on the right, on the left and at the top. AT this case it will be attached to door frame. It is done almost similarly to the inner roller, only it is desirable to fill it large quantity foam rubber. On the hinge side, we place it flush with the jamb, and on the upper and lock sides, we extend it by about 3-5 mm, depending on the size of the gaps between the door leaf and the frame. If the roller is made too large, the door will close hard, with effort. If the roller succeeds small size, it will not perform its main function - sealing the opening. Therefore, it is important here to catch golden mean". In conclusion, we nail the remaining lower edge of the skin and install the peephole, handle and locks. Don't rush at this stage. As the saying goes, measure twice, cut once. Make cuts in the upholstery for locks and handles with care, do not cut off the excess. It will be a shame at the very end of the process to screw up all the work done. Now you know how to sheathe the outside of a wooden door yourself. This will significantly increase its insulating properties, as well as increase the sound insulation of the front door.

How to upholster a metal door with dermantine yourself

We take a tube with and a brush and coat the entire perimeter of the metal door. Then we apply a sheet of foam rubber and, lightly pressing on it, glue it. Next, cut the foam exactly along the profile with a clerical knife sheet metal. If the blade is sharp, this procedure will be quite easy and pleasant. Now we apply glue to the upper end of the door (if it is inner side) or on the reverse side of the upper flashing (if it is the outer side). When using glue, be sure to follow the instructions for use! Then we glue dermantin and, similarly to the method above, we check the uniformity of its distribution. Then we glue the leatherette from the side of the loops. And then - and from the lock side, pulling right hand with a slight effort, and with the left - driving off excess dermantin. So, the bottom edge remains. Applying glue on this side of the metal door is the most difficult. There are situations when the gap between the lower edge of the iron door and the floor is only two or three millimeters. If you are unable to glue the leatherette underneath, you will have to remove the door from its hinges. In this way, you can make your task much easier. When the fabric is glued from all four sides, with a clerical knife, carefully cut off the excess at the corner at the junction of the end and the flashing (porch), put a peephole, door handles and locks. As you can see, it is quite possible to upholster a metal door yourself. Try it - and sooner or later you will succeed!

Door trim is done according to different reasons. Among the main ones are the insulation of a wooden or metal entrance structure, as well as the creation of a new decorative coating. It should be noted that all the work can be done independently, but to get a really high-quality result, you need to make every effort and accuracy. If everything is done correctly, the result will be a coating that will not only protect against the penetration of cold from the outside, but also provide an excellent visual appearance.

It all starts with what needs to be decided: how to sheathe the front door. The most acceptable option is the use of dermatin. Many mistakenly believe that this material has a lot of disadvantages. Yes, they exist and lie in the fact that such a product is very difficult to restore, in addition, leatherette contributes to the spread of fire. But this material has much more advantages:

1. It is not attacked by microorganisms that can promote the formation of mold and rot.
2. It has excellent moisture resistance. That is, water does not penetrate into the inner layer, which does not lead to undesirable consequences.
3. Has good durability. With proper care - the service life is tens of years. Even now you can find options for metal doors that were covered several decades ago. However, they still have not lost their appearance.
4. Not damaged when used household chemicals, washes well.
5. Withstands low temperatures. This makes it possible to use the material for finishing from the outside. Naturally, quality options should be preferred.

On a note! Leatherette is a type of artificial leather. Such products are positioned as an excellent substitute for natural options.

To really choose quality product, you should pay attention to a number of parameters. Namely:

• Wear resistance, which should be at least 30 - 35 thousand cycles.
• Flexibility. Artificial leather should stretch, and cracks and creases should not form.
• Imitation natural material should be as plausible as possible.

There are many low-quality fakes on the market that lose their appearance in a very short time.

Preparatory work

Do-it-yourself sheathing of entrance doors requires a complex preparatory activities. They are as follows:

• A schematic drawing is being prepared if it is planned to give the structure a more presentable appearance.
• A list of materials that will be used in the work is compiled:
  • Leatherette. You should select the product in special stores where it is present big choice in texture and colors. It must be borne in mind that these products are purchased with a margin.
  • Insulation, which is used for additional sound and heat insulation. To do this, you can choose felt, foam or synthetic winterizer. The thickness varies within 1 - 2 cm. It will depend on the pattern being created (tightening). In order to obtain beautiful sealing rollers, it is advisable to give preference to a heater that has a round, elongated shape.
  • Glue and decorative studs needed for fixing. The second option is selected depending on the type of hat that will play the role of a visual element.

It is difficult to imagine: how to sheathe the front door without the right tools. Therefore, the necessary set is being prepared:

1. Small head hammer comfortable handle to hammer nails.
2. Professional or semi-professional stapler. A set of brackets (8-10 mm) is purchased separately for it. This tool allows for preliminary and additional fixation.
3. A stationery knife or good scissors - for cutting out.
4. A screwdriver or a set of screwdrivers that will help dismantle and mount handles, as well as other elements.
5. Pliers to remove old skin or deformed nails.

Before finishing the front door with dermantine, a number of preparatory procedures are performed:

• The doorway is freed from unnecessary details - handles, locks, peepholes, chains. It is much better to work if the canvas is not removed from the hinges. In the absence of proper experience, all measurements, circumcisions are performed with great care.
• If it is planned to beat a door that already has decorative coating, then it is removed first.
• It often happens, especially with iron parts, that they are susceptible to rust. It should be cleaned up.

On a note! It is necessary to thoroughly clean all elements from any damage. wooden elements may have cracks and chips, they are covered with a special putty.

Finishing events

Door trim with dermantin is performed on two sides: internal and external. Technologically, these two processes have some differences. There are also works that are performed when upholstering wooden and metal doors.

Working with wooden structures from the inside

All work begins with the fact that the scheme for opening the door is determined - to the apartment or entrance (to the street in a private house). The correct choice of the size and location of the sealing rollers depends on this.

Often, wooden canvases open inwards. Therefore, this option should be considered.

The technology is:

Installation of dermantin is carried out according to the following scheme:

• Fixation starts from the top. small plot tucked under the insulation, decorative carnations make their way along the edge.
  

  On a note! The initial fastening is very difficult to perform. For this, a stapler is used, the staples of which are clogged in several places.

• The installation is checked for evenness. Make sure there are no distortions.
• Further, carnations make their way on the left, and then on the right side. All work is done carefully - by constantly stretching the canvas. Wrinkles must not be allowed.
• Lastly, the lower part is nailed.

At the end, marks are made for cutting holes for handles and an eyelet.

The door frame is considered complete. But only a direct coating is obtained. To get a picture, markup is performed. Points are marked on the canvas, which are located at regular intervals. Carnations are hammered on them. It is important to consider that the process starts from the center, excluding the strong tension of the leatherette.

Working with wooden structures outside

From the side of the street or entrance, work is carried out as follows:

1. The door closes. One centimeter recedes from the edge of the canvas.
   

   On a note! If the door does not have the necessary sound insulation, then a sticker of one or two layers of material should be provided. It is very convenient when the first layer has a self-adhesive side, the second one is attached to the brackets.

2. An insulating roller is fixed at the bottom. For this, a piece of leatherette is used, in which a piece of foam rubber is wrapped. It should be placed slightly higher than the bottom edge of the canvas. It is necessary to avoid displacement, otherwise, it will cling to the threshold. Many masters believe that this is an extra element, so it is advisable to proceed from a specific situation.
3. Upholstering the fabric with insulation starts from above, and then descends from both sides. It is important to consider that the material should not sag. If this is allowed, then further actions will be of poor quality.
4. On the last step perform sheathing of a wooden door with leatherette. It is fixed along the folded edges. If necessary, get a picture - breaks through the entire surface.

On a note! Many masters believe that it is at the final stage that the lower roller is formed. It is formed by bending leatherette lined with chopped foam rubber. That is, the roller turns out to be solid. Be sure to check that it does not cling to the threshold.

The upholstery is considered complete when the bolsters are installed around the perimeter of the box itself.

Work with a metal door - interior decoration

The situation is a little more complicated when it comes to how to sheathe an iron door. The methods of sheathing outside and inside are also different.

Currently, many manufacturers are trying to interior decoration the entrance door was carried out in production. For this, decorative inserts made of MDF are used. But it happens that cheaper options do not have such elements, then it becomes necessary to fit the doors with dermantine with your own hands.

Work is carried out according to a certain scheme:

The video will help you understand the intricacies of the process:

If required, a drawing is created. To make it more beautiful, you can use the remnants of artificial leather. The technology lies in the fact that one edge is nailed to the right place, then the strip is stretched and fixed again in desired area. It turns out a coating that has a more pronounced texture.

Working with a metal door - exterior decoration

If it is necessary to sheathe the entrance metal door from the outside, then a lining of small thickness is used.

The order of work is as follows:

• The synthetic winterizer or foam rubber is cut in size, which should be eight to ten millimeters smaller than the door leaf. The dermatin is immediately cut off. Its canvas should be equal to the size of the insulation plus 6-7 cm.
• The insulation is attached with glue, which is evenly applied around the entire perimeter of the iron door. You need to wait a while for the material to adhere well. If this is not done, then further work may be of poor quality. The finished area should have an even surface.
• Now a layer of dermatin is laid. It is evenly distributed over the entire surface. The edges are folded over the edge of the door leaf panels. The bent section must be fixed, for this, glue is used, which has a quick setting.

If you do everything carefully, then the front door trim will turn out to be very respectable. At the end, you should carefully install everything additional elements(handles, locks).

Some details

Currently, dermatin refers to a whole range of materials. Therefore, if it is necessary to purchase, it should be borne in mind that there are types of coatings that can successfully replace it:

1. Eco-leather. Polyurethane coated fabric. This option is not suitable for rooms with high humidity.
2. Viniliskin. Its composition is very similar to natural leather. This species has many excellent decorative solutions which are suitable for different situations.
3. Amidiskin. Perfect solution in order to ennoble the door with your own hands, because the material has good elasticity. Buying cheap varieties should be avoided.

There are many options for how to sheathe the door most effectively. All of them are described in the following article. However, leatherette upholstery, which flaunted on the front door in almost every Soviet house, has not lost its popularity to this day. And all because this is one of the few ways to finish the door leaf, which is easy to do with your own hands. Naturally, the main parameter will be accuracy and strict adherence to all stages.

They don’t argue about tastes and aesthetic preferences, which is why the door manufacturer offers entire catalogs of the most varied design both the door leaf and the entire entrance group. For those owners who are not satisfied with the content of the catalogs, there are huge opportunities for upholstery of doors with a mass of materials, one of which, perhaps the most popular, remains artificial leather.

How to sheathe doors. Video

how beautiful leather doors, each owner decides for himself, however, it is difficult to blame this coating for practicality. Leatherette, the price of which is several times lower than genuine leather, and if you buy domestic, not too dense material for upholstery when used indoors, is inexpensive and available in thousands of tint variations and textures. You can buy everything from crocodile skin to the most incredible and fantastic textures. Yes, and with less pretentious even canvases are also on sale.

Do-it-yourself door upholstery with leatherette, the video of the process of which we presented above, does not require any special tools and skills, and you can finish both wooden and metal doors in this way. Another undoubted plus of the material is that under it you can deftly hide any insulation, which will also isolate from excess noise. Moreover, in recent times you can find a ready-made kit for upholstery of doors, which includes nails with special caps, insulation, rollers and the cut of leatherette of the required size.

The choice and size of leatherette

Leatherette is distinguished not only by color, but also by thickness, so when choosing a material, it is worth considering the complexity of the desired surface. The thicker the leatherette, the more difficult it will be to give it a certain shape. But at the same time, thick material is harder to damage and retains heat better.

When choosing an upholstery kit, you should pay attention to the size of the cut, because for metal doors and for wooden size piece will be different. Standard metal doors will require a piece of leatherette 12 cm larger than the canvas, and wooden ones - 15 cm larger than the canvas. Nails are selected special, with a curly hat large diameter, and the color of the hat can look harmonious with the color of the accessories or merge in color with leatherette. Perhaps it will be interesting to look at a contrasting solution if the pattern of the location of the nails is somehow interesting.

Selection of nails and auxiliary materials

As an option, some make out each hat separately - wrap it or glue it with the remnants of leatherette, it also looks whole and harmonious. As a lining, you can, of course, use foam rubber. It is cheaper, but there is no sense from it, as from a heater. It is better to choose a good and soft insulation, like Isoton. Metal doors are glued with simple glue A moment, following virtually the same algorithm of actions that we will consider for wooden doors.

To upholster wooden doors with leatherette, you will need the usual tools that are in every home - a hammer, screwdrivers, pliers, a glue brush, a construction knife and scissors. A construction stapler will greatly simplify the task, but you can do without it by replacing the staples with thin nails.

wood door technology

The main work is done, it remains only to make rollers from the remnants of leatherette to create a pattern on the canvas. In principle, for this you can use decorative braid, and the pattern can be anything. For some reason, rhombuses are incredibly popular. Feng shui, maybe.

Yes, and one more thing. The word "leatherette" has never been, is not and never will be the letter N. "Dermos" is Greek for "skin", and leatherette, respectively, is the material that replaces it. But in general, in this way you can quickly and inexpensively update the door leaf, give the doors a completely different look and at the same time learn something new about the use of borrowed words. Good luck with the repair!

Leatherette is finishing material with special qualities. It does not wrinkle, does not fade from exposure sun rays, has a structural pattern, looks elegant and beautiful. In the features of the material, its strengths can be distinguished:

• Durability. Leatherette is able to retain its properties for 7-10 years.
• Ease of care. To make the upholstery look pleasing to the eye, you can simply wash it with water and lubricate it with cream from time to time.
• Moisture resistance. The material is water repellent. This reduces the risk of damage to the insulation and waterproofing of the door structure.
• Frost resistance. Their technical qualities and decorative properties leatherette retains even at low winter temperatures.
• Variety of colors. The material goes on sale in in large numbers variants of its shade. Therefore, enough is available to buyers wide selection the colors of the future upholstery of the door, ranging from black to light shades of the material.
• Antiseptic properties. Leatherette does not rot, mold and does not promote the reproduction of insects.
• Chemical resistance. Dermatin is resistant to exposure to it chemical substances. Therefore, it can be washed using various household products.
• Democratic price. The cost of upholstery with dermantine does not exceed the available limits. This circumstance makes the material popular for most owners of apartments, cottages and private houses.

When finishing wooden and metal doors with dermantine with your own hands, another one is solved important problem: heat and sound insulation of the room. Leatherette upholstery delays the penetration of street noise and cold outside air into the housing.

The disadvantages of this material are much less:

• Flammability. Door upholstery with dermantine is prone to fire. Exposure to an open flame is especially dangerous for her.
• Inconvenience in repair. Cuts in leatherette are almost impossible to mask so that they do not spoil the appearance of the upholstery. The best solution it will be a complete replacement.
• Material strength. To tear or cut leatherette upholstery, no special effort is required. Therefore, it must be handled carefully and not make enemies for yourself in order to avoid wrecking on their part.

What is required for work

To do the upholstery of the front door with dermantine with your own hands, you need to stock up necessary materials and a simple tool. Their list includes:

• screwdrivers;
• a hammer;
• construction knife and scissors;
• brush for applying glue;
• roulette;
• construction stapler;
• leatherette;
• lining material (foam rubber or batting);
• polymer glue;
• decorative braid (it beautifully fixes the upholstery on the door leaf area).

In addition to the above materials and tools, decorative nails will be required to sheathe the door. They must be selected in accordance with the design of the upholstery and in harmony with the fittings of the front door. The caps of these carnations look beautiful and have a different color or plastic coating. Fasteners are sold by weight or in packs of 100 or 200 pieces each.

Leatherette upholstery technology

Finishing the door with dermantine can be done on both sides, from the inside or outside. Working instruction includes several stages.

Preparatory work

Preparing the door for upholstery with dermantine is done as follows:

Roller device

Leatherette rollers are necessary for high-quality insulation of the doorway. Before making them with your own hands, you need to consider the direction of opening the door. If it opens outward, four rollers will be required for each side of the door leaf, if inward, three will be enough.

To make one roller with your own hands, you need a strip of leatherette 10-15 cm wide and a cut lining material. One of the edges of the strip is attached along the side of the door face down. Then the lining is folded with a roller and wrapped around the other edge of the leatherette strip. Fixing the rollers on the door leaf is carried out with a stapler, carnations or glue when finishing its metal surface.

Installing the backing material

When upholstering a door, the lining material plays the role of thermal insulation and absorption of noise from the street or staircase. The use of foam rubber as a lining is not as effective as the use of batting or isolon - more modern heaters. Therefore, it is recommended to perform insulation with these materials. The lining material must completely cover the entire leaf of an iron or wooden door. When it is opened externally near door hinges you need to leave a small gap.

When working with a wooden door leaf with your own hands, the lining is fixed with a stapler. Its brackets are placed along the perimeter of the door at a distance of 15-20cm from each other. If you need to properly sheathe an iron door, its canvas is smeared with glue, and the lining material is evenly laid on top and slightly pressed.

Covering the door with leatherette

For a neat do-it-yourself tightening of a metal door, you need to tuck the edges of the leatherette and fix them from the inside with the help of staples. Then you should glue the edge of the lining material with glue, hem and press the upholstery. Work is performed with gradual movement in one direction.

upholstered with leatherette wooden canvas doors are easier. The edges of the material must be tucked up and nailed with furniture studs with a step of 10-15 cm.

When doing the tightening with your own hands, you need to pay attention to the fact that the attachment points of the rollers do not peek out from under the edge of the leatherette. In addition, when upholstering, leave a few millimeters from the edge of the door so that the new cover does not interfere with the movement of the door leaf.

Hardware installation

At the last stage of work, upholstered door equipped with the necessary fittings. To do this, at the locations of the technical holes in the door leaf, you yourself need to make small cuts in the upholstery. Holes can be felt through the lining and leatherette. Then the castle door handle and the peephole must be installed in their original places. Using decorative nails, you can make some nice pattern on the upholstery of the door leaf. After that, it remains only to hang the door on the hinges and enjoy the work done.