Classic paper wallpapers cause much less enthusiasm among consumers than modern finishing materials. Manufacturers produce an extensive range of wallpaper products, among which non-woven products are in great demand. They have high strength, wear resistance, a rich range of shades and textures and give the interior original flavor. But in order for the decoration of walls and ceilings to be impeccable, you need to know how to glue non-woven wallpaper, glue the corners correctly and apply the adhesive.
The complexity of working with non-woven material lies in the density of products. But this moment should not confuse anyone, because after a couple of glued strips comes experience and pasting skills. Vinyl wallpaper on a non-woven base does not have to be smeared with glue, it is enough to process the walls or ceilings in the rooms. Important advantages of materials are high plasticity and thickness, thanks to which minor base defects can be hidden.
The main nuances of how to glue vinyl wallpapers on a non-woven basis:
- Due to the composition of cellulose fibers and polymer binders, the material belongs to the universal type of coating, suitable for pasting any room.
- You can cope with the work yourself, which allows you to save on the services of a professional team. In extreme cases, you can glue wide non-woven wallpaper with an assistant.
- The surfaces to be glued must be prepared in advance. The color of ceilings or walls should be uniform and not contrast with the shade of the wallpaper, which has a translucent texture.
- It is easy to achieve a perfect coating without visible seams, thanks to the presence of a well-finished edge of the strip that is glued end-to-end. This also contributes to the meter width of the rolls.
- The wallpaper is fast and easy to install, no glue is required on the strips. It is enough to smear the surface with the adhesive mixture, attach the prepared piece of wallpaper and press firmly, expelling bubbles.
It is necessary to cut the material into strips of the required length after checking the products for defects and calculating the footage of the room. domestic producers produce rolls with a width of 53 cm according to the standard. Foreign companies offer consumers products with a large width of 106 cm (meter) and custom size in 70, 90, 100 and even 140 mm.
On a note! Very high quality non-woven vinyl is produced by Germany, Italy, Belgium and France. The width and length of the rolls varies, so when buying, you need to pay attention to the dimensions. finishing material.
With the help of non-woven wallpaper, you can create an effect on the surface seamless coating. This is very much appreciated, so finishing materials are very controversial.
Meter width - fewer joints on the wall, but these are not the only advantages of non-woven fabrics:
- Simple and fast gluing procedure. Each person can handle how to glue wallpaper based on non-woven fabric with a little patience.
- You will spend less time and money buying and gluing one meter roll of vinyl than buying and gluing two rolls of narrow canvases, plus you save glue.
- A wide variety of textures and shades allows you to realize interesting design ideas. In the line of non-woven wallpaper there are options that imitate wood, natural stone.
- It is technically competent to call non-woven materials three-layer - an opaque base, non-woven fabric, vinyl coating as a decorative layer that gives texture and relief.
- Dense structure and elastic properties, thanks to which it is possible to mask the unevenness of the walls, microcracks, and slight differences in the surface in height.
- The high tensile strength provided by the non-woven backing and the resistance of the vinyl to abrasion and color loss.
An additional advantage of wallpaper is ease of care. They can be cleaned dry and wet way. If the humidity level rises in the room, the material does not stretch and “do not shrink”.
To give the room the new kind, redesign or implement a bold interior solution, wallpapered ceilings and walls can be painted in the desired shade.
Checked! Non-woven wallpaper can be painted up to ten times. It is unlikely that anyone will want to experiment with color so often, but the material withstands three times the staining for sure.
The first rule to follow before purchasing a finishing material is that vinyl on a roll looks different than on a pasted surface. If you buy wallpaper in a specialized store, you can evaluate appearance material according to the samples presented at the stands.
How to choose meter wallpaper:
- To obtain harmonious design interior, choose finishing materials from one collection, series and batch of one manufacturer.
- Since wallpapers are not cheap, you need to make sure that they correspond to the declared quality by asking the seller to demonstrate that they have a certificate.
- If several wallpaper options are displayed, they first look at the lower and upper rows, and then the middle - at eye level they often place a product that is not in demand or is more expensive.
- You need to choose a pattern and color to your taste, but you must also take into account general concept interior, compatibility colors and wallpaper textures with furniture and room decor.
To get visual solid surface without seams after pasting, it is better to choose wallpaper with foamed vinyl coating. Non-woven materials do not shrink after drying, which greatly simplifies the work with the finish.
There are no significant drawbacks to non-woven wallpaper. To obtain perfect coverage walls and ceilings, it is important to qualitatively prepare the base for subsequent pasting. It is necessary to level the surface if it has defects, and carefully cover large cracks, putty and sand with fine-grained sandpaper after drying.
Some inconveniences of how to glue non-woven vinyl wallpaper:
- Step-by-step preparation of the basis for the upcoming pasting. The surface serves as a base for wallpapering, so the strength of fixing the canvases depends on the quality of the preparatory work.
- You need to stock up on an additional roll of wallpaper in case there is not enough material or if the strip breaks during the gluing process and lies unevenly on the wall. It is important to choose rolls from the same lot.
- Wide wallpapers are glued quite easily, but you need an assistant for accurate pasting. He will be able to hold the edge of the strip so that it does not arbitrarily stick to the base smeared with glue.
- Air bubbles remain under the wallpaper, which must be driven out with a roller to the edges of the canvas. If this is not done, the material in such places swells and gradually lags behind.
- If the question arose, how to glue vinyl wallpaper on non-woven fabric in hard-to-reach places, it is necessary to leave allowances and then calculate the material consumption.
Non-woven canvases are obtained from cellulose fibers, so they are completely harmless to health. After applying a vinyl coating on them, the effect of vapor impermeability of products is not excluded, which can be attributed to the disadvantages of finishing materials.
Experts advise! On sale there is wallpaper on non-woven and paper basis, which differ in characteristics, gluing technology and cost. How to check the layering of canvases? If possible, you need to tear off a small piece of wallpaper and see how many layers it consists of.
Tools and materials
One of the advantages of non-woven wallpaper is that the canvases themselves do not need to be coated with glue. So it doesn't need to work. extra space to accommodate wide bands.
To independently paste over a room with meter-long wallpaper, you need to prepare in advance necessary tools and materials for work, the list of which is presented below:
- Non-woven wallpaper and glue that fits them.
- Building level, preferably laser.
- Two clean containers: one for glue, the other for water.
- Narrow metal spatula, long-haired roller.
- Plastic spatula, glue brush.
- Tape measure, pencil and cutting knife.
- Foam sponge, clean rags, sandpaper.
- Putty (start, finish), sickle mesh, primer.
Listed are the tools and materials that are required not only for gluing wallpaper, but also for high-quality preparation of surfaces for gluing.
For the final decoration of the premises, you can buy in advance decorative plinth or a corner made of gypsum, polyurethane foam, polystyrene. It gives the room a complete look and hides the connecting seams between the canvases on the wall and ceiling.
Masters recommend! With the help of decorative fragments, you can hide minor defects in trimming the wallpaper. Therefore, it is easier to glue skirting boards and corners after gluing the canvases, and not to start the wallpaper with a spatula under the already glued finish.
Surface preparation
The base for gluing non-woven wallpaper must be carefully prepared. Ignoring this moment leads to a rapid lag of the canvases, material breaks in the places of cracks and an aesthetically unattractive appearance of the room.
The preparatory stage is the most difficult and time-consuming:
- Remove socket covers, switch cases from the walls, dismantle the fasteners and remove the chandelier, and carefully seal all the holes formed with masking tape.
- Before gluing meter-long wallpapers with your own hands, you must carefully remove the old coating - peel off the wallpaper by soaking it with water, blur the whitewashed ceiling, wash off the paint and plaster.
- Assess how the base looks like - the presence of joints, deformations, cracks. Putty all problem areas, laying a sickle mesh and let the mixture dry. You can apply finishing putty to the entire surface completely to smooth out the roughness and partially even out the differences in height.
- If the condition of the walls and ceilings is completely unsatisfactory, they are sewn up with drywall sheets, and the seams are covered with putty. Dark GKL need to be processed completely.
- Places for applying the starting and finishing putty process with sandpaper. After that, carefully sweep away the dust, wash the walls or wipe with a damp cloth.
- Apply a primer in several layers, pausing to dry the compositions. The primer is selected depending on the material of the surfaces to be glued.
Perfect smooth walls create good base for wallpapering. If you do not use a primer, then part of the glue will quickly be absorbed into the surface, and the wallpaper will stick worse. The durability of the finish depends on how well the preparation is done.
Attention! The primer on the walls and ceiling should dry well. The time for complete drying is indicated on the container with the primer.
Ideally, all measurements should be taken before buying wallpaper, since this is easy to do using a tape measure. If the material has already been purchased, it remains to cut the strips.
How not to make mistakes in the calculations for specific example if the dimensions of the room are 4 * 5 * 2.5 (length, width, height):
- Measure the height of the room from floor to ceiling = 2.5 m.
- Add 5-15 cm to this figure "in reserve" = 2.65 m.
- Check the length of the roll - it happens 10, 15, 20 meters.
- The number of whole strips in a roll is counted = 10/2.65=3.77 pcs.
- Round the value down = 3 bars.
- The perimeter is calculated - (length + width) * 2 \u003d (4 + 5) * 2 \u003d 18 m.
- Make a deduction for windows and doors, suppose = 1m + 1m + 1.5m = 3.5m.
- The width of windows and doors is taken from the perimeter = 18-3.5 = 14.5 m.
- The resulting value is divided by the width of the roll = 14.5 strips.
- Calculate how many rolls you need = 14.5 / 3 = 4.83 rolls.
For pasting the walls in a room with dimensions of 4 * 5 * 2.5 meters, you need five 10-meter rolls of non-woven wallpaper 106 cm wide. In this case, you need to buy one more roll for pasting the walls above the door, above and below the windows. The material is cut into strips of the required length (2.65 m). By the same principle, the material consumption for gluing the ceiling is calculated. The length of the strip is taken as the distance from the wall with windows to opposite side. If a pattern is made on the wallpaper, each strip is adjusted to the previous one, carefully combining the pattern.
As an option, you can glue meter-long wallpaper on a non-woven base, directly from a roll without cutting.
After preparing the required number of strips for gluing, it is necessary to apply markings. On the walls, vinyl wallpaper begins to be glued from the window opening. With the help of a plumb line, a control point is marked and a vertical strip is drawn. On the ceiling, markings start from any edge perpendicular to the windows, since the canvases need to be glued end-to-end. In rare cases, the strips are placed along the length of the room, then it is convenient to mark the surface from the windows.
Important! So that when daylight there were no visible joints of the wallpaper, the strips are glued perpendicular to the windows. But if by design idea the wallpaper pattern on the ceiling should run along the length of the room, you can glue strips along the wall with windows.
For vinyl wallpaper choose universal formulations or special means for non-woven materials. Before mixing the product, you need to check the compatibility of the adhesive and wallpaper, as different compositions are suitable for light, heavy, dense samples.
How to prepare glue:
- Pour into a bucket clean water in the right proportion.
- The liquid is stirred to form a funnel.
- Slowly pour in the glue and mix constantly.
- Allow the mixture to swell well for 20-30 minutes.
- Stir again before use.
The composition is applied only to the surfaces to be glued, but in order for the wallpaper to hold on to the ceiling more firmly, it is possible to coat the canvases themselves. It is worth adhering to this recommendation in the hot season, as the glue dries quickly on the wall.
Attention! Do not violate the proportions of water and glue indicated by the manufacturer on the package. Otherwise, the mixture turns out to be of an inappropriate consistency and loses its adhesive properties. For work it is better to use freshly prepared glue.
Gluing process
How to glue non-woven wallpaper, every master will figure it out, since the fundamental differences from traditional technology there are no jobs. It must be remembered that it is not necessary to apply glue to the strips, except for pasting the ceiling or carrying out repairs in a very hot season.
An important condition that must be observed is to exclude drafts so that heavy canvases do not lag behind the surface.
How to glue non-woven wallpaper correctly:
- Prepare the walls and ceiling, the necessary tools and glue.
- Choose the direction of the stripes on the wall, taking into account the angle of incidence of light.
- Withstand the pattern to get the effect of a continuous pattern.
- The main rule of gluing is that the canvases are combined strictly end-to-end.
- A strip is prepared, the wall is smeared with glue using a roller or brush.
- Immediately fix the canvas on the wall at the level of the control line.
- The canvas is leveled from the center to the edges, expelling the air with a roller.
- Cut off the excess part of the wallpaper and proceed to sticking the next strip.
To cut the canvas evenly, a wide spatula is applied to it and trimmed carefully with a knife. Products with a pattern are measured immediately, carefully adjusting the pattern, and the excess is cut off so as not to confuse the location of the ornament. Since the strips are glued end-to-end, before fixing the next strip, the edge of the previous sheet is not smeared with glue.
Master's advice! Until the glue is completely dry, do not open the windows or open the doors. If this situation happened by accident, the canvases are immediately glued.
On video: Master class for gluing non-woven wallpaper.
Pasting difficult areas
In every room there are places that cause some inconvenience when decorating with wallpaper. These are corners (and they are often uneven), door and window openings, niches or arches.
How to glue meter-long non-woven wallpaper on difficult sections of walls and ceilings:
- Internal corners. Measure the width of the strip from the edge of the previous web to inner corner, add 1 cm to the allowance. They smear the corner with glue and glue the strip, grabbing part of the adjacent wall and wrapping the edge by 1 cm. The canvas is leveled and the excess is cut off. By the same principle, paste over the second part of the corner. The wallpaper is cut vertically so as not to touch the bottom strip. The edges are combined and after drying, an inconspicuous joint is obtained.
2. Door or window opening. If used plain wallpaper or copies without a pattern selection, it is easier to stick them, since you can skip the area above the doorway and then glue it in small fragments. When vinyl wallpaper on non-woven with a pronounced pattern, the pattern will have to be combined immediately, without missing the area above the door or under the window. The strip is carefully measured, a place for a window / door is cut out in it, and glued to the wall, combining the ornament.
3."Recessed" or expanded corner. If such a section in the room is located in a conspicuous place and attracts attention, overlap cannot be done. How to glue vinyl wallpaper based on non-woven fabric in this case? The strip is led onto an adjacent wall by 2 cm, but the overlap will not be the same. In the very bottleneck the overlap recede from the edge to the corner of 1 cm, after which the width of the roll is measured from this point and a vertical line is drawn. The overlap in an uneven corner will be approximately 1 cm, but will not be very noticeable.
Some masters when pasting uneven corners using the double cut method. How to glue non-woven meter-long wallpaper in this case: stick two strips with a large overlap of 5 cm, pressing them strongly into the corner; using a rigid profile, the wallpaper is cut vertically in the center of the corner, the excess is removed, the edges of the strips are smeared with glue and ironed with a roller.
On a note! In the places where sockets and switches are installed, the wallpaper is glued as usual, but the location is marked with a cross electrical devices. Cuts are made along the marked lines, the wallpaper is folded inward, and after the glue has dried, the boxes are mounted in their original place.
Coloring
An important advantage of vinyl is compatibility with paintwork materials. Non-woven wallpaper is often glued as a base for further painting work. The type of paint is chosen in accordance with the instructions indicated on the package.
Staining nuances:
- Buy paint for interior work.
- Tinting the entire volume in the desired shade.
- Thoroughly mix the coloring composition.
- Apply with a roller on the wallpaper, wringing it out slightly.
Non-woven fabrics can be painted about ten times. It should only be borne in mind that painted walls and ceilings have low vapor permeability. Typically, consumers paint rooms covered with vinyl no more than three times.
New! On sale there are non-woven photo wallpapers that look interesting in interior design. With the help of a scale image, you can transform the living room or bedroom. The technology for gluing non-woven photo wallpapers on a wall does not differ from the standard process - surface preparation, glue preparation, strip gluing. The only caveat is that if the photo wallpaper does not fit completely, the picture is placed in the center and the canvases are trimmed along the edges.
Working with wide vinyl products does not require special skills. The material adheres well to walls and ceilings made of concrete, drywall, wood. You can cope with sticking alone, but this affects the speed of the work.
It is more difficult to glue wide strips on your own than with an assistant, but it is possible.
If the canvases lag behind the walls or fall from the ceiling, there may be several reasons:
- Poor surface preparation.
- Incorrectly selected and prepared adhesive.
- The glue had time to dry before gluing.
- The room is drafty or very hot.
- Air bubbles formed under the wallpaper.
Wide vinyl canvases decorate the room, creating the effect of an integral artistic composition without joints. The pasting process is not fundamentally different from the standard technology; you can do the work yourself. To get the desired result, choose high-quality wallpaper, glue and prepare the walls and ceiling well for pasting.
Stages of gluing wallpaper on non-woven base (2 videos)
How to glue wallpaper on non-woven base (20 photos)
Non-woven wallpaper can be of two types: with a pattern and for painting. Such products are able to easily mask the imperfections of the walls that remain after repair work. Therefore, non-woven wallpaper is in great demand. You don't need any special skills to stick them.
You should be aware that the non-woven base is able to slide along the wall, and therefore it will be possible to paste over without outside help. If you choose wallpaper for painting, you can easily change the range of interior colors. In this case, the room will always seem fresh.
To date, large-width wallpapers are used quite rarely, but on sale you can find a large number of of this material. Such wallpapers have some advantages:
- wide-width wallpapers can greatly simplify the gluing process;
- in this case there will be a minimum number of seams that spoil the appearance of the room.
Necessary preparatory work
In order for the gluing to be done with high quality, you will need to perform some preparatory work. First of all, it is necessary to calculate with maximum accuracy the number of rolls of material that will be needed for pasting the room. To do this, you will need to measure the width and height of the room on each side separately. In the process of counting required amount rolls will need to be added to the length of the canvas a few centimeters on each side in reserve. For clarity, you can draw a diagram on paper.
In the process of choosing non-woven wallpaper, you will need to pay attention to the batch number, which is indicated on the package. It should be the same on all rolls. If there is a drawing, it must also be identical.
In order for the wallpaper to fit correctly on the wall, you will need to prepare the room. The walls must be carefully aligned. This is especially important to do if you plan to paste wide wallpaper that will not lie correctly on uneven walls. If the surface is not leveled, then this will further affect the quality of the joints.
Sockets and switches will need to be removed. The wires will need to be insulated so that the adhesive mixture does not get inside the boxes. All walls will need to be carefully treated with a primer mixture, and then dried.
You will need to prepare the following items:
- Video clip. Will be used for edging.
- Film made of polyethylene.
- Short bristled brush.
- Plastic spatula.
- Container for adhesive mixture.
- roller.
- Roulette.
- Simple pencil.
- Level.
- Adhesive mixture for non-woven wallpaper.
Back to index
Do-it-yourself non-woven wallpaper gluing technology
First of all, you need to mark the walls. Non-woven wallpaper has an excellent edge, butt-glued. Marking should start from the corner of the room. In these places, the canvas will be overlapped so that they can be processed correctly. If you plan to stick a material with a width of 1.06 m, then in all directions from the corner you will need to set aside 1 m.
By using a plumb line or building level and a simple pencil will need to outline a vertical line to the height of the builder. With a tape measure, it will be necessary to mark 1.06 m from the drawn line. Thus, it will be necessary to draw all the walls.
If there is no drawing, you will need to measure the height of the room with a tape measure in the place where the piece of wallpaper will be pasted, while adding another 10 cm. The roll is bent onto the rolled part so that the edges match. In this case, you will get an even fold. You will need to run your hand along the fold, and then cut it with a construction knife. In this case, you can use a new clerical knife. Thus, wallpaper is prepared for the entire room.
The canvases will need to be rolled into loose rolls so that the front side is inside. Thanks to the non-woven base, problems in this case should not arise.
Next, you need to dilute the adhesive mixture according to the instructions. It is allowed to use only adhesive solution for non-woven wallpaper. Water is poured into the prepared container, after which glue is poured out in a thin stream. In the process of preparing the mixture, it must be constantly stirred in order to exclude the formation of lumps that can interfere with the quality of sticking the wallpaper. The adhesive solution must stand for a while to swell. A plastic mesh can be installed in the container, which will remove excess glue.
The roller will need to be immersed in a container with a solution, and then run over the grid. Next, you need to spread glue on the wall for gluing one canvas. The panel must begin to be glued from the top.
You need to take hold of the extreme part of the canvas, and then attach it to the wall. The roll slowly descends, in the process you need to smooth the wallpaper from the middle to the edges with a brush. In this case, you can also use a plastic spatula, but all actions must be performed carefully, as the wallpaper may be damaged.
Glue wallpaper based on non-woven fabric so that they fit snugly against the wall. Bubbles and wrinkles are not allowed.
After gluing two sheets with a roller, you need to roll the seams of the material. The piece of wallpaper that remains below will need to be carefully cut off. This should be done after the wallpaper has dried. It is necessary to calculate everything so that the plinth installed later can cover the bottom of the wallpaper. A border of the required thickness can be installed at the top of the wall.
Back to index
How to glue non-woven wallpaper on the corners
The first step is to prepare the corner of the room. This must be done even in the process of filling the walls. The corners are equipped with plastic fixtures that are attached to the putty on the walls. The entire product must dry completely, only after that it will be possible to start gluing non-woven wallpaper. In the process of gluing the corner, the wall and the plastic corner will need to be carefully coated with an adhesive mixture.
The canvases will be overlapped, it is not recommended to glue the whole panel at the corner. In most cases, the corners in the rooms are not ideal, and therefore defects may occur: the corners of the material will wrinkle, the strip will warp. To eliminate this, it is necessary to glue the corners correctly.
The canvas should be glued in such a way that a slight overlap is obtained on the wall, which is located nearby.
The next strip is glued on another wall, it is glued to the corner with a slight overlap. Next, this “tail” is cut off using construction knife, you need to navigate along the vertical angle.
As a result, up to 2 cm of the panel from the adjacent wall will be glued under this canvas, the first canvas will rest against the corner with its edge.
With a general algorithm for gluing wallpaper with a non-woven base, according to most experts. They believe that this material is one of the highest quality and most comfortable. Currently, non-woven wallpaper is becoming more and more popular.
Main advantages
Structural non-woven wallpaper has the following characteristics and features:
Non-woven wallpaper is made from environmentally friendly raw materials. In addition, this material meets all sanitary requirements. It is used not only for decorative trim walls. Gluing non-woven wallpaper can also be carried out on the ceiling. This material is often used for finishing office and residential premises.
Application features
Finishing facilities
In this case, before you start pasting, you should make sure that the walls are absolutely even. Accordingly, they should not have any cracks, bumps or other surface defects. On the preliminary stage all surfaces must be thoroughly cleaned of the old coating.
In some cases, getting rid of old wallpaper is not very easy. In order to facilitate this process, they need to be properly wetted. In this case, you can use water and ordinary rags. Thus, the wallpaper will quickly soften. It is best to remove them with a spatula. It should be noted that the surface of most walls in ordinary apartments far from perfect. In some cases, repairs may even be required. Thus, at the preliminary stage, it is necessary to putty problem areas. This also applies to corners. Then comes the primer. This can be done with glue or special solution for deep penetration. Only then it will be possible to start gluing non-woven wallpaper.
Important conditions
How to glue non-woven wallpaper? Of course, there is a certain technology. Since not everyone knows how to properly glue non-woven wallpaper House master, you should pay attention to the following:
The importance of the preparatory phase
Non-woven wallpaper can be glued quite quickly and efficiently, if certain recommendations are strictly followed. In this case, it is very important preparatory stage. This process is not difficult. First of all, you need to level the base. As a rule, this is done with putty. Next, the walls should be primed. Then you need to prepare the glue. For non-woven wallpaper are available special formulations. It is worth noting that the preparation of the base is best entrusted to a professional plasterer-painter. As for further action, then almost everyone can master them without problems.
Features of the adhesive composition
Do not trust the instructions on the packages too much. They don't really match up. practical application. The composition, which is prepared exactly according to the attached instructions, turns out to be too liquid. It is suitable for gluing lungs paper wallpaper, but no more than that.
Process features
Self-gluing non-woven wallpaper usually starts from one of the corners. Care must be taken. In the corners of the walls, the wallpaper should be pasted with a twist of up to 2 cm. This place should be well smeared with a solution. It is worth noting that non-woven fabric, which is the basis of such wallpaper, does not need to be pre-soaked with glue. This, by the way, is one of the main advantages of such material. Glue needs to be smeared only on the wall. Thus, there is no need to cut the roll into separate parts.
The material must be laid on the floor. The roll must be unwound, and then glued to the wall strip. It is recommended to carefully straighten the canvas. In this case, you can use a roller or a plastic spatula. In order to stick the first strip, you need a level. The canvas will be easier to align if you draw a reference line on the wall. This applies in particular to striped wallpaper. The curvature of the walls, as a rule, is very noticeable.
We remove the joints
It is worth noting that gluing the first strip is quite easy. Subsequent problems may arise. This is due to the need to join the canvases. Many are wondering how to make these places invisible. In fact, this will not cause any difficulties. The fact is that the wallpaper slides quite well on the surface, which is smeared with glue. In order for the joint to become invisible, you need to attach the canvas to the wall. At the same time, it should be as close as possible to the neighboring lane. You can finally move them with your hands.
The position of the canvas may need some adjustments. After the optimal position of the strip is chosen, it must be carefully smoothed out. There should be no air bubbles under the canvas. It is worth noting that such wallpaper must be cut correctly. This skill must be mastered. It is useful for preparing the canvas for ceiling baguettes. Initially, a cut line is formed. For this, it is best to use a plastic spatula. The glued canvas is pressed into the corner between the baguette and the wall. Next, you need a knife and a straight ruler. With the help of them you need to cut off excess wallpaper.
Before sticking vinyl wallpaper, the material must be translucent to make sure its quality and sufficient density. Sticking high-quality durable vinyl wallpaper is considered sufficient. daunting task. In addition, you need to prepare the glue, special tools and materials, namely a bucket for preparing glue, scissors, a spatula, a wallpaper roller. Pasting the walls with high-quality durable vinyl wallpaper requires some effort, but it's worth it, because such a finishing material looks just fine on the wall. Be sure to purchase glue designed to work specifically with vinyl wallpaper.
Modern non-woven vinyl wallpaper
Stylish vinyl wallpaper, made on a non-woven basis, is in great demand, because it is quite durable and quality material. Italian and German vinyl wallpapers are very high quality, because they are made from the best materials, therefore, they are durable, environmentally friendly, modern design. Italy and Germany are considered leaders in the production of high quality wall coverings.
Vinyl wallpapers are characterized by:
- Excellent design;
- The ability to hide the flaws of the walls;
- High quality and practicality.
Due to the variety of existing models, it is possible to introduce the most daring and modern ideas. A rich palette allows you to choose the desired option, which is most suitable for the stylistic decision of the room.
Since vinyl wallpapers are characterized by increased strength, they can be used for painting, thereby changing the stylistic decision of the room.
Important! In the production of vinyl wallpaper, foamed vinyl is used, which comes on a non-woven or paper basis.
Vinyl wallpaper, made on a paper basis, are more environmentally friendly, because they allow the walls to breathe freely. Vinyl wallpapers are resistant to high humidity, so they are easy to wash and clean, which is important when carrying out repairs in the kitchen and nursery. In addition, such material is able to absorb sounds.
How to glue non-woven vinyl wallpaper correctly: the choice of materials
Wallpaper is considered the most popular material used for wall decoration. Enough interesting option are stylish vinyl wallpapers made on non-woven base.
Such wall decoration materials can be very different and they differ:
- The number of layers;
- Density;
- By weight.
Before sticking vinyl wallpaper, you need to use an additional layer of primer, which is applied to the wall
When choosing such wallpapers, you definitely need to know how to stick them correctly and what materials and adhesives are best to choose. Before pasting the walls with stylish durable vinyl wallpaper, it is best to initially prepare the surface and level it with special materials. However, it is worth remembering that when decorating walls, you cannot use putty based on PVA glue, because this can harm vinyl wallpaper.
Which adhesive is best for non-woven vinyl wallpaper
Many people are interested in what kind of glue is best to glue non-woven vinyl wallpapers so that they stay on the walls for a long time and the aesthetic qualities of this material do not deteriorate. For pasting vinyl wallpaper, special adhesives are used or universal wallpaper paste can be used.
The main characteristics of such an adhesive composition:
- High resistance to humidity;
- Increased sliding ability;
- Excellent adhesion to the wall.
When sticking vinyl wallpaper, be sure to choose the right adhesive composition and follow absolutely all the instructions.
Due to the peculiarities of the adhesive composition, it is possible to easily correct the joints. In addition, such glue does not form lumps at all. Already a few minutes after dilution, the adhesive composition used for pasting vinyl wallpapers is completely ready for use, and in a closed container, the adhesive can be stored for several weeks. The most popular and popular is Metilan glue, presented in a wide range. After reading user reviews, you can be sure that this is the ideal adhesive for vinyl wallpaper.
Features of wall pasting: how long do non-woven vinyl wallpapers dry
Vinyl wallpapers look just great, but in order to stick them, you need to follow the rules and do all the work in a clear sequence.
The process of pasting walls with stylish high-quality vinyl wallpaper consists of several stages, namely:
- Preparation of materials;
- wall pasting;
- Corner processing;
- Processing sockets and switches.
Before sticking wallpaper on the wall, you need to check each individual roll for matching shade and pattern, and then cut each canvas into separate strips. You need to cut the strips so that the pattern matches and creates a holistic pattern throughout the room. Working with vinyl wallpaper is particularly simple, because the glue must be applied exclusively to the wall and it is not at all necessary to impregnate the canvas itself with glue. In order for the wallpaper to lie flat on the wall, you need to make markings using a level before starting work.
Corners require special attention. The canvas must be glued in such a way that only 5 cm enter the corner, and the subsequent strip must be glued with an overlap. Then you need to cut the double joint sharp knife and you can join the edges
At the time of wallpapering, all switches and sockets must be completely de-energized. The boxes themselves must be removed and a cross cut should be made in the place of the socket or switch, and then the corners should be bent inward. After the wallpaper is completely dry, you can install the switches and sockets in their original place.
When carrying out pasting wallpaper, it is very important to know how much vinyl wallpaper dries. They dry quickly enough, the most important thing is to prevent the formation of drafts. The wallpaper will dry in just a day.
Symbols on non-woven vinyl wallpaper
Many are interested in what vinyl wallpaper is and what glue is needed for finishing and repair work.
Vinyl wallpaper is a special type of finishing wall material which is characterized by:
- Reliability;
- Diversity of texture;
- Density;
- Hides minor surface imperfections.
To understand the features of this finishing material, you should pay attention to the applied symbols. Such designations may be represented by letters or symbols. Letter designations indicate what material the wallpaper is made of. After letters There are a number of icons, each of which corresponds to certain parameters.
Table of symbols on wallpaper rolls
In particular, these parameters indicate:
- Moisture resistant;
- Light fastness;
- Feature of pasting;
- Features of the adhesive application.
The difference between each type of vinyl wallpaper is quite possible to recognize by the printed on the label symbols. This will help you correctly select the required wall covering, which is suitable in all respects.
Is it possible to paint non-woven vinyl wallpaper
Many people think that vinyl wallpapers are harmful because they do not allow the walls to breathe and emit harmful substances. Vinyl wallpaper can be silkscreened or hot stamped. Each of the types is divided into its own separate subspecies and has its own special pros and cons, which must be considered when choosing such a finishing material.
Vinyl wallpapers are characterized by the fact that they can be painted and special paint is used for this. Such a wall covering can imitate various materials, in particular tiles, fur, wood and much more.
If desired, you can draw on the wallpaper beautiful patterns, which are applied to the pre-painted surface of the wallpaper
Painting can be done:
- In one tone;
- Special drawings are applied using stencils;
- Used sticker for vinyl wallpaper.
If there are certain doubts about choosing a shade or when applying a pattern, then it is best to start painting from an inconspicuous place. It is imperative to paint such a wall covering with paints that penetrate deep into the structure, because in this way it is quite possible to obtain a rich deep shade. For painting, water-based or acrylic paints are used.
How to glue the corners of non-woven vinyl wallpaper
Vinyl wallpapers are characterized by increased strength and reliability, but at the same time, many say that they are quite harmful and cannot be used for pasting the bedroom and children's room. The harmfulness of such wallpapers lies in the fact that they have high density and do not allow the walls to breathe, because they do not allow air to pass through. When choosing vinyl wallpaper, you must definitely take into account the peculiarity of pasting them. It is especially difficult to stick wallpaper in the corners, because rarely in which apartment do they meet perfectly even corners, so you need to take into account all the features of the work. The execution of the work should involve several stages.
The end result depends on various factors, such as:
- Wallpaper quality;
- Wall preparation;
- Compliance with the required temperature regime;
- Proper application of glue in the corners of the room.
The strips in the corners need to be glued with an overlap, and then trim the remaining edges with a sharp knife after it is completely dry, because the wet wall covering will tear
When carrying out wallpapering in the corners of the room, you need to cut them into separate strips, especially meter-long wallpapers. Before gluing, you need to soak well adhesive composition corners so that the wallpaper holds well. It is quite possible to mask the glued corner with various decorative elements.
How to properly and how to wash non-woven vinyl wallpaper
When decorating walls, it is important to take into account the particular care of the applied wall covering. If you wash the wallpaper incorrectly, you can harm them and remove the surface, thereby damaging the structure wall covering. However, it is imperative to take care of the wallpaper, because dirt and dust have a bad effect on the condition of the wallpaper, and lead to the fact that their attractiveness will be lost.
According to the conventions, vinyl wallpapers are divided into:
- Washable with soapy water;
- Washable with household chemicals;
- Resistant to high humidity.
When cleaning vinyl wallpaper, beware of abrasive cleaners.
In addition, there are wallpapers that absolutely cannot be washed, but can only be wiped with a slightly damp cloth. If there is no dirt on the vinyl wallpaper, but only dust, then you should use a vacuum cleaner.
Important! When buying a wall covering, it is important to consider the peculiarity of the material. For the kitchen, it is best to choose washable wallpaper with resistance to high humidity.
How to glue non-woven vinyl wallpaper (video)
Proper pasting of vinyl wallpaper has many various nuances, but following all the rules, it is quite possible to create an original unique surface that will last for a long time.
The guide will save you from many common mistakes and tell you how to glue non-woven wallpaper correctly: about gluing corners, marking walls, cutting wallpaper and gluing technology.
Non-woven wallpaper can be with or without a pattern. The second type will require additional coloring. Such wallpapers mask the imperfections of the walls well, are the most simple material for finishing.
Preliminary preparation of the room before pasting
At the preliminary stage, it is important to correctly calculate the required number of rolls. To do this, on each side of the room, you need to measure the width and height. When calculating the required number of rolls, it is important to add several centimeters to the length of the required web.
Note! You should buy wallpaper from only one batch number. This number is usually found on the roll label. Only rolls from the same batch number will definitely have the same shade and pattern texture.
Before wallpapering, the walls must be leveled, wallpapers wider than 50 cm are very sensitive to unevenness Preliminary preparation of the room before wallpapering is. This fact is especially important for wide wallpapers, which are extremely intolerant of irregularities, especially at the joints.
Sockets and switches must be dismantled, wires isolated. Treat the walls with primer and be sure to dry. Protect the remaining furniture in the room, the floor and unused areas of space with plastic wrap.
Preparing corners for pasting
In the corners, the panels are glued with an overlap, so their irregularities are hidden This process should be done at the stage of filling the walls. In the corners you need to put special plastic corners, which will be attached to the walls with putty. After the design is dry, you can start pasting. When pasting a corner, the wall is treated with glue, including the corner. The panel is glued with an overlap, experts do not recommend gluing the whole canvas into a corner. Because the corners are usually far from ideal and the formation of defects is possible. The overlap on the next wall should be small.
Necessary tools and materials:
- you will need a roller to roll the edge
- polyethylene film
- plastic spatula
- for glue bucket and roller
- soft bristled brush
- pencil and tape measure
- plumb line
- building level
- glue designed specifically for non-woven wallpaper
The process of pasting the walls with your own hands
Stage number 1. Wall marking
When working with non-woven wallpaper, marking is necessary because the sticker is butt Markup is recommended to start from scratch. Wallpaper on this basis has an excellent edge, the butt pasting method is used. Overlapped panels are glued in the corners. This is done in order to enable good further processing. If the width of the roll is 1.06 meters, then a meter must be set aside on both sides of the corner.
Initially, a vertical line is drawn with a pencil using a level or plumb line. From the drawn line with a tape measure, 1.06 meters are marked. So it is necessary to draw all the walls that are being prepared for pasting.
Stage number 2. Preparing the site and cutting the wallpaper
Make sure that the pattern fits together, flaws will be very noticeable with large ornaments After marking the walls on the floor, you need to spread a clean polyethylene film. It will be needed as a place for rolling rolls. This is done by laying the wallpaper face down. When trimming the panel, it is important to take into account the pattern on the wallpaper.
If there is no drawing, then the place where the first piece will be glued is measured with a tape measure. Another ten centimeters are added. The roll is folded over the rolled part so that the edges match. First, the bend is carried out by hand, and then it is cut with a knife. Prepare wallpaper for pasting the entire room.
Prepared panels are folded into loose rolls face down. Non-woven wallpaper is tolerant of such manipulations.
Stage number 3. Glue preparation
When diluting the glue, lumps should not be allowed to appear, they negatively affect the quality of the sticker Wallpaper glue should be bought specifically for non-woven wallpaper. It should be diluted according to the instructions that are indicated on the package. Usually, glue is diluted according to this technology: water is poured into a bucket, glue is poured into it in a thin stream, it is constantly stirred. There should be no lumps, otherwise they will interfere with high-quality gluing. In order for the glue to become suitable, you need to let it stand for a while. It will be useful to insert a special plastic mesh into the bucket, which will help remove excess glue.
If you already had non-woven wallpaper,
Stage number 4. Applying glue and wallpapering the walls
Dip the roller in a bucket of glue, run along the grid, and then apply glue to the wall. Apply glue only at the rate of pasting one panel. The cloth should be glued on top. The canvas is taken by the edge and applied to the wall. Gradually lower the roll down, smoothing the wallpaper from the middle to the edges with a special brush or roller. You can also use a plastic spatula, but be careful not to damage the wallpaper.
Note! Wallpaper should be firmly pressed against the wall, there should be no bubbles inside or wrinkles.
Wallpaper always starts to glue from above, moving down, from the middle to the edges of the panel When several canvases have already been pasted, then each subsequent seam of the wallpaper will have to be additionally rolled with a roller. The piece of wallpaper that remains below should be carefully cut off. It is recommended to do this after the wallpaper has dried. By the way, estimate that the plinth completely covers the place where the wallpaper is cut.
It is important! In many construction stores today wallpaper is sold in a meter width, which is non-standard for us. But the meter width has its advantages, because it simplifies the pasting process.
