Scher-Khan car alarm programming. Scher-Khan car alarm remote control programming Sherkhan 5 temperature setting

Programming the CTCTS functions using a key fob consists of four steps.

1. Enter programming mode and select the programming menu. To enter Menu No. 1, press the I + II buttons simultaneously for 2 seconds. To enter Menu No. 2, press the I + IV buttons simultaneously for 2 seconds. The siren will give one short signal, alarm the car will flash once, confirming the successful completion of STEP 1.

2. Press the IV button to select the Menu function you want to change. The number of presses must correspond to the number of the selected function. For example, to select function 4, you need to briefly press the keyfob button IV four times. Each button press will be confirmed by a short siren tone (if enabled) and a flash of the car alarm.

3. Wait a few seconds. The system will confirm the number of the selected function to be changed with short siren beeps and car alarm flashes. The number of signals will correspond to the number of the selected function.

Note:

If, when choosing a function, you made a mistake with the number of clicks and (or) there are no siren and alarm signals, then you need to repeat all the actions starting from STEP 1.

4. Press the I button to select the factory setting for the function. To confirm this, the siren will give one short signal, the alarm will flash once. Press the II, III, or IV button to select optional function values. To confirm this, the siren will give two, three or four short beeps, the car alarm will flash two, three or four times.

Note:

If you hear one long signal from the car alarm siren, this means that the system has exited the function programming mode. To continue programming, repeat all steps from STEP 1.

ATTENTION!

If you want to change more than one function from the Menu you have selected, then the selection of each function to change must begin with STEP I.

Menu of programmable functions

Menu #1 [Button (I + II)-]

Note on function 1-4: This function allows you to select "Panic" or Jack Stop mode™ (robbery protection):

Resetting all programmable functions of Menu No. 1 to factory defaults

1. Enter programming mode. Press buttons I + II simultaneously for 2 sec. The car alarm siren will sound one short beep and the alarm will flash once, confirming the success of STEP 1

2. Briefly press button III on the car alarm key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time, three siren sounds will sound, the alarm will flash three times, confirming the factory settings of all menu 1 programmable functions.

Menu #2 [Button (I+IV)-]

Resetting all programmable functions of Menu No. 2 to factory defaults

To reset the programmable features to factory defaults, two steps are required.

1. Enter programming mode. Press buttons I + IV simultaneously for 2 sec. The car alarm siren will beep once, the alarm will flash once, confirming the success of STEP 1

2. Briefly press button III on the key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time after this, three siren sounds will sound, the car alarm will flash three times, confirming the factory settings of all programmable car alarm functions of menu No. 2

KEYFOB-COMMUNICATOR CAR ALARM SCHER - KHAN 5

Preparing the key fob-communicator for work

Before using the key fob, you must bring it into working condition, because. during transportation and storage, an insulating gasket is installed between the contact of the battery and the contact plate of the key fob, which prevents the battery from discharging before operation. Before using the key fob, remove it. To do this, release the battery cover lock, press the cover and slide it in the direction opposite to the antenna. Remove the battery. Remove the insulating pad between the battery and the collector plate. Install the battery back, observing the polarity indicated on the bottom of the battery compartment. If there is no indication of the polarity of the battery, then it is set with a negative terminal towards the antenna. Close the battery cover. After that, the keychain is ready to work.

Symbols on the display of the key fob-communicator of the car security system

	Timer start indicator
	TURBO mode indicator
	Passive arming indicator
	Mode activation indicator "" Free hands""
	Siren indicator
	Shock sensor off indicator
	Vibrating alert indicator
	Indicator of turning on the automatic control of the central lock by ignition
	Door open indicator
	Trunk/hood open indicator
	Shock sensor alarm indicator (optional sensor)
	Car owner call indicator

Scher Khan security systems have a long range of two-way communication. Autorun Sherkhan 5 can be performed according to several settings, depending on the desire of the owner.

[ Hide ]

Main characteristics

Deactivation of the signaling from the key fob

The system can operate in a passive mode, when the protection is activated half a minute after closing all doors and covers on the body. If the doors do not open when the system is turned off, it will automatically arm. To use the passive mode, it should be activated by briefly pressing the second and third buttons of the main key fob.

Passive operation mode is active (the Passive icon is lit on the display)

If the doors and the trunk lid were opened and closed, the system will turn on protection half a minute after the lock of the last element is clicked into place.

Keychain - communicator

The main key fob supplied in the kit has the following functional features:

• thanks to the four-button scheme, it is possible to control all system functions;
• the signal from the key fob is encoded according to a special Magic Code scheme, which prevents interception and recording;
• the built-in display with illumination provides visual display of all operations;
• when working with the system, the key fob confirms commands with a sound or vibration signal;
• additional information from sensors can be displayed on the screen;
• the key fob is the main tool for programming automatic start;
• using the key fob, the system parameters are configured.

After unpacking and installing the system on the car, it is necessary to bring the main key fob into working condition. To do this, you will need to remove the dielectric gasket installed between the contact pads of the battery and the key fob power circuit.

Action algorithm:

1. Open the battery cover. To do this, open the latch and slide the cover to the bottom of the key fob.
2. Remove the battery from the compartment.
3. Remove the gasket located along the entire length of the element.
4. Return the battery to the local location, observing the installation polarity indicated on the sticker. If there is no marking, remember that the negative pole of the battery is always directed towards the antenna of the Sherkhan Magikar key fob.
5. Close the lid and lock the latch.

Pictograms on the keychain Sherkhan Magikar 5

The following symbols and icons may appear on the screen:

• timer start (A);
• turbo timer mode (B);
• passive activation of the system (C);
• automatic activation mode without pressing the buttons (D);
• included siren (E);
• shock detection sensor (F) is off;
• vibrating alert is active in the key fob (G);
• control of door locks after starting the ignition (H);
• open trunk lid (J);
• the engine is switched on in the autostart mode (K);
• system state (L);
• open doors (M);
• field for displaying hours, temperature and data during autorun (N);
• operating mode Valet (O);
• working alarm or dimensions not switched off (P);
• shock sensor triggering (Q);
• key fob battery indicator (R);
• signal level (S).

Marat Askarov demonstrates setting the clock in the Magicar 5 key fob.

Autostart security system

Under the autostart of the system, they mean turning on and off the protection without pressing the buttons on the key fob. The mode is called “hands free” and is activated by pressing button one on the main key fob for two seconds. The system automatically turns on or off at a distance of up to 35 meters from the vehicle. When operating the alarm in conditions of strong interference, this distance can be reduced to 15 meters.

The black oval highlights the hands-free mode icon

The hands-free mode can only be controlled using the main key fob with a display.

Auto engine start

When using automatic start, you need to remember and follow a few rules:

1. Using autorun is allowed only when the machine is placed in a ventilated area and subject to visual contact.
2. Produce automatic start prohibited when people are standing in front or behind the vehicle.
3. The parked car must be fixed with a working parking brake.
4. Before enabling the autorun feature on machines with manual method shifting speeds, it is necessary to set the "software neutral".
5. Monitor coolant or oil levels.
6. Set in advance on the microclimate control unit the direction of airflow and the desired air temperature in the cabin.
7. Do not pass the key fob to play with children.

Before turning on the engine start system on vehicles with a manual gearbox, the neutral position of the gearbox lever must be programmed. There are three options for this, the description of the steps for each of them is given below. The mode can be programmed through the system settings menu.

The first option provides:

1. Stop in a parking space, apply the parking brake, move the gearshift lever to neutral and remove the key from the lock cylinder.
2. With the engine still running, open the door, leave the vehicle and slam it behind you. The motor must stop.

If you need to pick up things from the trunk, then you should use the second option:

1. After setting the lever to the neutral position and turning off the ignition, the driver exits the car and does not close the door behind him.
2. Open the trunk and take out everything you need.
3. Close the door and then slam the luggage compartment lid. The engine will stop and be ready for automatic start.

The third option looks like this:

1. Set the neutral position and apply the parking brake.
2. Close doors.
3. Press button two on the key fob for two seconds.
4. Turn off the ignition and get out of the car.
5. Close the door, after which the motor will stop.

When installing autorun on the machine, the neutral setting procedure is not required, just put the box selector in the parking mode.

To provide remote engine start, it is necessary to install a device to bypass the immobilizer.

The engine can be started by pressing the second key fob button. After starting the engine, the display will show the remaining operating time. This parameter is programmable and can be 45/25/15 or 5 minutes. If necessary, the car door can be opened by pressing the first button and within 20 seconds, insert the key into the lock and turn to the active ignition position.

Display in engine mode

Autostart by timer

To connect and disconnect the function, a short press on the buttons three and four is used, after which the icon with the inscription Timer will turn on on the screen.

There are two options for working, which are configured programmatically:

• daily run, repeating every 24 hours;
• auto-restart every 2/4/8 hours.

To enable daily start, a so-called redundant mode must be carried out.

For this you need:

1. Turn off the timer mode by briefly pressing buttons two and four.
2. To enter the setting, press buttons one and two for a few seconds.
3. Turn on the mode by pressing 13 times on the button four. Each press will be accompanied by a signal.
4. Select the repeat time by pressing the buttons (the second button gives a repeat of 8 hours, the third - 4 hours and the fourth - two hours).
5. Enable timer.

Enable timer start

Auto start by battery temperature and voltage

The engine is switched on according to the temperature inside the cabin minus 15 or 25 degrees in winter time and plus 60 in the summer.

1. Turn off the timer start mode.
2. Press button four 21 times.
3. Use the buttons to select the switching threshold (the fourth - plus 60, the third - minus 25 and the second - minus 15).
4. Enable timer.

When setting the voltage to onboard network the system will operate at a value of 11.5 V.

1. Press 20 times on the fourth button.
2. Turn on voltage start with button two.

In all warm-up modes, you can vary the operating time of the power unit.

For this, the steps are:

1. Press button number four twelve times.
2. Select the operating time using the buttons from the first to the fourth, choosing each time from the range of 5-15-25-45 minutes.

Scher-Khan Magicar 5 alarm auto start malfunctions

The main causes of malfunctions that are possible when auto-starting the Sher-Khan Magikar 5 alarm:

1. The engine does not start even though automatic start backup is running normally. The cause may be oxidized fuse legs in the power supply circuit of the main unit. Another reason may be the failure of the standard immobilizer crawler or the sticking of the contacts in the control relay.
2. The motor starts and then stalls after a few seconds of operation. At the same time, in normal mode, the engine starts without problems from the ignition switch. One of probable causes there may be damage inside the five-pin relay installed in the main unit.
3. A common reason why the start does not work is incorrect parameter settings. To eliminate this, you must return the system to factory settings and re-program.
4. Sometimes the reason that the automatic start stopped working may be the inclusion of the Valet mode. This mode is characterized by a permanently lit control diode. After the setting mode is turned off, the start returns to normal.

Excellent operational characteristics and the "Sherkhan Magikar 5" alarm system has high reliability. The instruction manual gives a detailed explanation about the principles of using this device and its main functions.

purpose

The instruction "Sherkhan Magikar 5" indicates that this alarm can be controlled by the user remotely, which is helped by an exclusive keychain communicator. The display is made of liquid crystal material, so it is considered particularly reliable.

A specially built-in system regulates a single mechanism of interaction between the processor unit and the key fob-communicator. You can control the alarm from a distance of 1500 m.

The engine starts after a special command is given. It is usually sent along the key fob, the outer part of the device, the internal timer. This does not take into account the temperature in the car, and the voltage level of the battery is also unimportant.

Advantages

Preparing the key fob for work

Before using the key fob, you need to perform several manipulations, since there is no battery in it during transportation. It is located separately, and not in the proper compartment. This is necessary to conserve battery power. in full. When you remove the battery, no power is consumed, so there is no need to additionally recharge the device.

To place the battery in the right place, carefully remove the latch that holds the Sherkhan Magikar 5 battery cover in its original position. In this case, malfunctions are excluded, since all structural elements are made with maximum quality. This applies to both cutting parts and the material from which they are created.

After performing this action, it is necessary to move the cover itself to the side that runs opposite to the protruding antenna. The battery for power should be carefully installed in the compartment. As with any battery, polarity is provided here, so the position of its sides can only be determined after familiarizing yourself with the graphic pattern near this compartment.

If any indicators are missing, then the Sherkhan Magikar 5 signaling is placed with a minus sign in the direction where the antenna is located. After correct installation a characteristic melody is heard, which indicates the completion necessary action for the correct operation of the system. You only need to close the battery storage compartment cover, and then install the appropriate lock on it.

Arming

To activate the security mode, you must first turn off the ignition, and close all compartments of the car to ensure the free operation of "Sherkhan Magikar 5". The operating manual determines that the button number 1 on the key fob is then pressed with only one touch. It is not necessary to hold it for a long time, a point and moderate touch is enough. The system will automatically translate everything necessary elements machine in guard mode. The existing locks on the doors will be blocked, the starter will not work until the owner himself removes this mode.

When the car alarm "Sherkhan Magikar 5" is armed successfully, a person can trace some signals:

1. The siren will sound once with a moderate whistle.
2. The emergency light signal will also make itself felt once.
3. An LED indicator will turn on, which will show that the car is under protection by means of measured flashing at a frequency of 1 time per second.
4. The headlights flash five times simultaneously. Further, the image of the closed lock will remain lit until the car is unlocked, and the headlights will go out.
5. The key fob will give only one short signal.

Enable sensors

When the LED begins to flash steadily, this means the activation of the system control over the state of all possible inputs and methods of penetration into the car, which the Sherkhan Magikar 5 cannot allow. The instruction manual reports that even the sensors for calling the owner and ignition control are additionally checked and constantly monitored, which allows the owner to calmly do any of his business at this time.

If connected additional function, which is responsible for regulating the delay of the cabin light, will also provide for the control of triggers, which usually do not begin to be guarded immediately, but only after a certain amount of time has passed. activates work 30 seconds after the machine has been armed.

Warning

The instruction "Sherkhan Magikar 5" warns users against inattention to the car. Do not leave doors, hood and luggage compartment open. If this happens, then the person suddenly, instead of the usual behavior of the car when arming, hears a three-time key fob signal along with a siren. In this case, the alarm also flashes three times at once.

On the display, you can see the image of the item that the owner of the car forgot to close. This happens only for five seconds, so the user may not have time to see the desired item. At the same time, the text FALL appears on the display. This is a direct indication that you should find an unclosed element and cover it tightly.

"Sherkhan Magikar 5" instruction manual defines as a device upper class, since it sets all vehicle communications on guard, but it bypasses the activated sensor. It will automatically be additionally protected after the owner closes it. The hood area is not reflected in common panel, as it refers to the trunk area.

Automatic transition to armed mode

Passive arming is a separate feature that can be enabled or disabled for Sherkhan Magikar 5. The autorun instruction provides - you just need to change the state of the selected function. If the owner decides to activate just such a mode, then immediately after the last door is closed, the timer is activated, and the security is turned on after 30 seconds.

When the countdown is started, the system constantly sends warnings that this mode will turn on. This happens every 10 seconds. If any door is opened at the specified time, the system will activate the armed mode at the countdown of 30 seconds after the last door is closed. You can see if this function is working by the word PASSIVE, which is always shown on the display in this case.

Alarm mode

When Sherkhan Magikar 5 is operating, malfunctions are unacceptable. When any door is opened, the system will automatically be in alarm mode for exactly 30 seconds. When this time is over, it will return to the standard state again.

If the cause that caused the alarm has not been eliminated by this time, the signal will sound every 30 seconds and last for half a minute. This cycle is repeated eight times. If even then the reason for the violation of the usual mode is not canceled, the system returns to the armed mode, but on condition that the active sensor is bypassed.

Features of work

If the shock sensor is triggered, that is, there is a strong impact on any part of the car, the Sherkhan Magikar 5 alarm will be in alarm mode for 5 seconds, during which a strong signal from the siren and alarm is given.

With a weak impact, that is, the activation of the warning zone, also regulated by the shock sensor, 4 short ones will sound, which are generated by the Sherkhan Magikar 5 car alarm. There were no malfunctions in this process, so the owner of the device can be confident in his own technique.

Many users appreciate the ease of use of Sherkhan Magikar 5. How to disable security mode? With a short one-time press on the key fob button number 2. If you correctly program all the functions of the device, the alarm will become a reliable assistant in ensuring the safety of the car.

How to set the temperature auto start of the engine on the Sher-Khan Magicar 5 alarm?

1. it only has a start on the discharge of the battery !!!
2. Attention! It is not possible to automatically start the engine only by temperature or only by low battery voltage. The time trigger enable condition is mandatory.

   Attention! During programming, the system must be disarmed and the ignition in the car must be turned off. The Hands Free mode is also disabled and the door is preferably open so that there is no re-arming during programming.

   1) Timed autostart setting (every 2, 4 or 8 hours)
   b) To activate the timed autostart mode, press the IV button 13 times in succession (the siren emits a beep after each button press; that is, press once, we hear a beep, press a second time - we hear a beep and so on 13 times)
   c) Wait for the siren to beep 13 times in a row.
   d) Then select the desired autorun time button II - 8 hours, III - 4 hours or IV - 2 hours.
   

   2) Setting autostart by temperature (when t is reached in the cabin -15, -25, +60)
   For the autostart to work correctly when the temperature is reached, 3 steps must be performed:
   
   2. Turn on temperature control (mode 1-21 in II, III or IV)
   a) Recall that the entry into the function programming mode is carried out by long pressing the I + II buttons.
   b) To activate the autostart mode by temperature, press the IV button 21 times in succession (the siren beeps after each button press; that is, we press once, we hear a beep, we press a second time - we hear a beep and so on 21 times)
   c) Wait for the siren to beep 21 times in a row.
   d) Then choose required temperature autorun button II - (-15), III - (by -25) or IV - (+60).
   e) After that, you need to turn on the timer from the key fob. Press simultaneously II + IV briefly, the display will show the inscription “timer”. If it was activated (lit) before programming, it must be switched off (also II+IV) and switched on again.

   3) Autostart setting by on-board voltage
   Implementation of the delay of the timer start up to the moment of discharging battery up to 11.5 V, is carried out as follows:
   1. Enable time trigger (mode 1-13 in II, III or IV) see 1) a), b), c)
   a) Entering the function programming mode by long pressing the I+II buttons.
   b) To activate the voltage autostart mode, press the IV button 20 times in succession (the siren beeps after each button press; that is, we press once, we hear a beep, we press a second time - we hear a beep and so on 20 times)
   c) Wait for the siren to beep 20 times in a row.
   d) This will enter the programming mode of the function Limit timer starts by battery voltage.
   e) After that it is necessary to press button II to activate the mode.

   Engine warm-up time:

   To set the engine warm-up time, set function 1-12 to position II.
   In more detail, you need to do the following:
   a) Entering the function programming mode is carried out by long pressing the I + II buttons.
   b) To set the engine warm-up time, press the IV button 12 times in succession (the siren beeps after each button press)
   c) Wait for the siren to beep 12 times in a row.
   d) Then select the desired duration of the start button I - 5 minutes, button II - 15 minutes, III - 25 minutes or IV - 45 minutes.

   Make sure the system is disarmed and lit before programming.

3. You set the desired temperature by programming the center. block and on the keychain you put the start on a timer, it seems like this.

GOST R 41.97-99 (Uniform provisions concerning the approval of systems alarm Vehicle(STSTS) and motor vehicles with regard to their alarm systems (STS))

GOST R 50009-2000 (Electromagnetic compatibility of technical means. Technical means security alarm. requirements and test methods)

Thank you for purchasing the SCHER-KHAN MAGICAR V two-way car security system.

The constant research and development of our company embodies the most advanced ideas and serves to satisfy all the needs of users of our systems.

Car alarm SHERKHAN MagiKar 5 is a complex electronic equipment of a car. The safety of your life, health and road conditions, the quality of work of nearby radio-electronic equipment and communication facilities depends on its functioning and proper installation. Trust the installation of the system only to specialized service stations. During operation, periodically check the correct functioning of the system.

PLEASE READ CAREFULLY!

ATTENTION!
When buying, check that the warranty card is filled out correctly.
The manufacturer and supplier of the system is not responsible for any ignorance of the instructions for installation and operation, as well as for errors made during installation.
If you encounter any problems related to the functioning of the system, please immediately contact service center for diagnosis or consultation.

The installation of the SCHER-KHAN MagiKar-5 car alarm must be carried out by qualified specialists. Car alarm is complicated technical device involving connection to electrical circuits vehicle related to the operation of the engine.

If an icon appears on the key fob display warning that the key fob battery is low, take measures in advance to replace the battery. We recommend that you store a new spare battery in the vehicle, keeping its original packaging.

PURPOSE

Car alarm SCHERKHAN MAGICAR V is car alarm with the ability to control over a radio channel using a key fob-communicator with a liquid crystal display. The system exchanges information between the key fob-communicator and the processor unit at a distance of up to 1500 m. SHERKHAN MagiCar 5 has a function for automatically starting the engine by commands from the key fob or by commands from the internal timer. The SCHER-KHAN MAGICAR V system is designed to work on gasoline or diesel vehicles with a fuel injection system and an on-board network voltage of 12V. The protection of the processor unit, shock sensor, call sensor, antenna unit is made according to the standard and provides for installation in the car. The siren is made according to and can be installed in the engine compartment, away from the exhaust manifold and high voltage systems.

Contents of delivery

When buying a system, make sure that the delivery is complete. The specified set of delivery is basic and can be supplemented in accordance with the wishes of the buyer with additional components.

Instruction manual 1
Installation Guide 1
Processing unit SCHER-KHAN MAGICAR V 1
Keychain communicator 1
Shock sensor with cable CN5 1
Vehicle call sensor with CN6 cable 1
Antenna unit 1
LED indicator (LED) 1
Temperature sensor 1
Interlock relay with block 1
Siren 1
Hood/trunk limit switch 1
6-pin power connector with cable and fuse CN1 1
6 pin power connector with cable CN2 1
9 pin control connector CN3 1
4-wire connection cable for antenna unit CN7 1
2 pin auxiliary channel control connector CN8 1
Car call sensor sticker 1
Sticker for antenna unit 1
Glass sticker 2

Additional components SCHER-KHAN MAGICAR

SCHER-KHAN BP-2 immobilizer bypass module
Keychain communicator SCHER-KHAN MAGICAR V (with display)*
Keychain SCHER-KHAN MAGICAR V (without display)*
* The processor unit can only remember the codes of three key fobs.

Keychain communicator functions

• Multifunctional, 4-button LCD keychain communicator
• Protection against interception of MAGIC CODE code packets
• Audiovisual confirmation of executed commands
• Vibrating bell
• Loud beeps
• Ultra long distance communication up to 1500 m with processor unit
• Automatic display backlight
• Low battery indication
• Vehicle battery voltage indication
• Indication of temperature in the passenger compartment
• Current time display
• Indication of engine operating time in automatic mode
• Remote engine start
• Programming the engine start time (accurate to the minute)
• Sound and visual alert reminder mode
• Operational, from the key fob, programming of all system functions
• Economy Power (one AAA element)

Processing unit functions

• Automatic engine start for vehicles with automatic or manual transmission
• Operation of the starting system with both petrol and diesel engines
• Operation of the starting system with engines having a turbine
• Starting the engine on command from the key fob
• Automatic engine start every 2 hours
• Automatic engine start at a pre-set time every 24 hours
• Monitoring the engine start by signals from the generator or by noise in the on-board network
• Personal code for access to the car interior if the key is lost
• Power output for controlling the car's central locking
• Trunk release power output
• Alarm control power output (two circuits)
• Programming the lock relay type
• Auto arming (programmable function)
• Sound warning before automatic arming
• Automatic return to armed mode if the door was not opened
• Sound warning before automatic return to armed mode
• Armed mode without siren signals
• Two universal programmable control channels for additional devices
• Ability to connect negative and positive door sensors
• Input for negative trunk sensor
• Locking and unlocking the door locks when starting and stopping the engine
• Possibility of arming with and without confirmation siren signals
• Open Door Alarm Warning (Programmable)
• Panic or JackStop mode
• Highly sensitive two-level shock sensor with sensitivity adjustment
• "Hands free" function for automatic arming / disarming when the owner moves away / approaches the car
• Dual mode hands-free function
• Parking lights not switched off warning

TECHNICAL SPECIFICATIONS

Alarm types:

Influence on the main and additional electrical equipment of the car

Control methods

• Remotely with a radio frequency transmitter (key fob) at a frequency of 433.92 MHz ± 0.2% with a power of not more than 10 mW
• From the ignition key
• Automatically based on signals from sensors

Electrical circuit protection

Fuses. (Automotive slow-acting fuses according to wiring diagram)

Spheres of protection

Other options

Batteries

* The table shows the average value. The service life of the key fob battery depends on the intensity of use of the key fob and the quality of the battery, the key fob operating modes.

ATTENTION!

Use only quality batteries. Battery Application Low quality can lead not only to a reduction in the life of the key fob, but also to its damage.

KEYFOB-COMMUNICATOR SCHER-KHAN MagiKar-5

Preparing the Keychain Communicator for Operation

Before using the key fob, you must bring it into working condition, because. during transportation and storage, an insulating gasket is installed between the contact of the battery and the contact plate of the key fob, which prevents the battery from discharging before operation. Before using the key fob, remove it. To do this, release the battery cover lock, press the cover and slide it in the direction opposite to the antenna. Remove the battery. Remove the insulating pad between the battery and the collector plate. Install the battery back, observing the polarity indicated on the bottom of the battery compartment. If there is no indication of the polarity of the battery, then it is set with a negative terminal towards the antenna. Close the battery cover. Keyring is ready to go.

Symbols on the keyfob-communicator display

	Timer start indicator
	TURBO mode indicator
	Passive arming indicator
	Hands-free mode indicator
	Siren indicator
	Shock sensor off indicator
	Vibrating alert indicator
	Indicator of turning on the automatic control of the central lock by ignition
	Door open indicator
	Trunk/hood open indicator
	Shock sensor alarm indicator (optional sensor)
	Car owner call indicator
	Engine running indicator
	Ignition on indicator in security mode, indicator of side lights not switched off
	Key fob transmitter operation indicator
	Battery discharge indicator of key fob-communicator
	VALET mode indicator
	Locking and unlocking indicator. Security Mode Status Indicator
	Clock indicator, car battery voltage, interior temperature, engine warm-up time during automatic start

Purpose of the buttons on the key fob-communicator

Example notation:

I - quick (0.5 sec.) button press
I- - long (2 sec.) button press
(I + II) - fast (0.5 sec.) simultaneous pressing of the buttons (combination of buttons)
(I + II) - - long (2 sec.) simultaneous pressing of the buttons (combination of buttons)

Note:

With a long 2 sec. pressing the I button, the modes change sequentially in the order (1) > (2) > (3) > (1) … . In mode (2), the "Hands free -" function has a high range work- symbol blinking.

Setting the time on the keychain communicator display

Setting the current time is required before starting the operation of the system or when changing the key fob battery. Follow the steps according to the table below.

ATTENTION!

Setting the correct time is necessary condition for correct operation automatic start of the engine by timer.

Setting the keyfob communicator, vibration call, owner call, temperature display standard "°F" or "°C"

To set the desired key fob operation mode, follow the steps in accordance with the table below.

Note: STEP 2 must be completed within 15 seconds. after STEP 1.

Arming [Button (I)]

Close doors, hood, trunk. Briefly press button I on the key fob. The system will switch to the armed mode, the door locks will be locked, the starter (ignition) interlock will turn on until the system is disarmed.

When arming:

Enable sensors:

Note:

If, when arming, you heard three key fob signals, and on the display for 5 seconds. the image of an open door or trunk flashes, this means that the door, hood / trunk is open in the car. The door, hood/trunk sensor will be immediately armed when its functionality is restored.

The hood area is not displayed separately, the hood sensor must be connected to the trunk sensor wire.

Disarming [Button (I)]

When the system is armed, briefly press button I on the key fob. The SHER-KHAN MagiKar-5 alarm system will be disarmed, the door locks will be unlocked, the starter (ignition) blocking will be disabled.

When disarming:

HANDS FREE function [Button (I)-]

ATTENTION!

The "Hands free" mode works only when using a keyfob-communicator with a liquid crystal display, when using optional keyfobs without a display, this mode is not available.

When you press button I on the key fob-communicator for 2 seconds. You can turn Hands Free on or off. When the "Hands-Free" function is enabled, the system will automatically arm itself when you are 15-35 m away from the car with the key fob-communicator*. or is removed from the security mode and unlocks the door locks when approached. The function has two modes of operation:

In the first mode, the mark on the display does not blink and the range of the function is minimal.

In the second mode, the mark on the display with the inscription "AUTO" flashes and the range is maximum.

The change of operating modes takes a long 2 seconds. by pressing the I button next order: (Function on, mode 1) > (Function on, mode 2) > (Function off) > (Function on, mode 1)….

Arming/disarming will be accompanied by a melodious signal from the key fob-communicator.

Continuous use of the "Hands Free" function is not recommended, as its use drastically reduces the battery life of the remote control.

* Note:

The distance from the unit to the key fob-communicator, at which the system makes a decision to arm or disarm, can vary and depends on a group of objective reasons: relative position antennas of the key fob-communicator and the antenna unit, the presence of metal objects near the antennas, from radio interference on the air, weather, etc. ...

When the hands-free function is enabled:

The mode change is accompanied by one signal from the key fob-communicator.

When the HANDS FREE function is turned off:

Starting the engine on command from the key fob [Button (II) -]

To start the engine, press button II on the remote control for 2 seconds. The system will be armed, the door locks will be locked, the car engine will start. After the engine has started, the key fob-communicator displays information about the time remaining until the end of the engine operation in automatic mode. Engine run time is programmable and can be 15/25/45/5 minutes (programmable function 2-4). To start driving. You need to open the door, insert the ignition key into the lock and turn it to the "ON" position. To do this, you have 20 seconds, after this time the system will transfer control to the ignition switch, if you do not turn on the ignition, the engine will be stopped.

If the launch did not occur the first time, the system will try again. The system makes no more than three attempts to start, after which it goes into standby mode. If the car engine does not start after the last attempt, contact a service station to diagnose your car.

At the time of launch:

SCHERKHAN MAGICAR V car alarm will not start the engine if:

• Ignition on
• The car engine is already running
• Door or hood/trunk open
• Backup mode failed for vehicles with manual transmission

On successful launch:

Note: If the car's engine is started automatically, the current time indicator shows the time remaining until the engine is stopped. Time is displayed in countdown mode. Time display format in this mode: [ XX min: XX sec.]

When the engine stops automatically:

Trunk opening [Button (III)-]

Press and hold for 2 sec. button III of the key fob, after which the trunk will open. If the system is armed (doors locked), it will disarm, the doors will unlock, and the starter will be disabled. To implement this function, it is necessary to have a trunk lock solenoid connected to the corresponding output of the main unit of the system.

When opening the trunk:

Checking System Status [Button (IV)]

If you need to check the status of the system, briefly press button IV on the communicator. Information about the state of the system will be shown on the display of the key fob communicator, as well as confirmed by siren and alarm signals.

When checking system status:

When checking the status of the system, the current time indicator shows the temperature value in the car interior. The temperature can be displayed in either °F or °C.

The temperature inside the car is 10°C.

Repeated short pressing of the button IV of the keyfob-communicator within 6 seconds after the first one allows you to view information about the car battery voltage in volts.

The voltage on the car battery is 13.9V.

Panic or JackStop mode (anti-seizure) [Button (IV)-]

When you press the button IV of the remote control for 2 seconds. The system will enter the "Panic" mode or JackStop mode (protection against seizure) - programmable function 1-4.. If the system was disarmed, it will arm itself, the door locks will be locked. The siren will sound for 90 seconds, the alarm will flash for 90 seconds. The "Panic" mode stops the automatic engine start mode. After 90 sec. the system will go into armed mode until it is disarmed by the key fob or emergency shutdown mode. Panic mode can be stopped by briefly pressing the I button. Panic and JackStop modes are used in case of danger or when it is necessary to draw attention to the car.

When activating the "Panic" and JackStop modes:

Differences in the "Panic" and JackStop algorithms (depending on the selected value of the programmable function 1-4):

ATTENTION!

JackStop mode should only be used in emergency situations. It is not a regular constantly used CCTTC mode. it provides for stopping the engine while driving.

When choosing one or another mode, consult with a specialist.

Siren Silence [Button (I+II)]

By briefly simultaneously pressing the buttons I + II of the key fob, you can turn on or turn off the siren signals. In this case, the key fob signals and alarm signals will work as usual. Siren activation is indicated by the presence of a symbol on the key fob display.

When the siren is turned on:

When turning off the siren signals:

VALET mode [Button (I+III)]

To disable the security functions of the system and when transferring the machine to a service station for maintenance, you can use the VALET mode. To do this, briefly press the I + III buttons on the remote control.

AT VALET mode you can control the locking and unlocking of the door locks. To lock or unlock the locks, briefly press button I.

The VALET mode is shown on the display with the symbol

To exit the VALET mode, briefly press the buttons I + III of the key fob

When VALET mode is enabled:

When turning off VALET mode:

Disabling the two-level shock sensor [Button (I+III)]

You can disable the two-level shock sensor. Simultaneously press and hold for 2 seconds. buttons I + III of the remote control, as a result, the sensors will be turned on or off. The indication of the sensor disconnection is the symbol on the key fob display. Switching off the sensor is necessary if you leave the car where false alarms are possible (the car is parked near tram tracks, a child or an animal remains in the car).

When the shock sensor is disabled:

When the shock sensor is turned on:

The shock sensor is called two-level, because it has two levels of response from the impact on the car.

In case of a weak impact, the system warns with 4 short siren sounds and 4 alarm flashes. Key fob - communicator gives a short tone signal, the symbol of impact on the car flashes on the display. If the impact is strong, the system goes into alarm mode for 30 seconds.

Central locking control for turning the ignition on and off [Button (I + IV)]

By briefly simultaneously pressing the buttons I + IV of the key fob, you can turn on or off automatic control central locking (CL) for turning the ignition on and off. If the function is enabled, the door locks will be automatically locked after 30 seconds. after the engine is started and all doors, the hood/trunk will be closed. The locks are unlocked immediately when the ignition is switched off. The function is indicated by the presence of a symbol on the key fob display.

When the central locking control function from ignition is turned on:

When the central locking control function is turned off from the ignition:

Passive arming [Button (II+III)]

The passive setting function can be turned on / off by briefly pressing the P + W buttons on the key fob. When passive arming is enabled, the system will automatically arm itself after 30 seconds. after closing the last door or after disarming with the key fob. The SHER-KHAN MagiKar-5 alarm system warns of passive arming with alarm signals and (or) siren every 10 seconds. If within 30 sec. doors (hood/trunk) were opened, the system will arm itself in 30 seconds. after closing the doors (hood/trunk).

When passive arming is enabled:

When turning off passive arming:

Setting the timer for automatic engine start [Button (II+IV)]

Briefly press buttons II + IV of the key fob to turn the engine start on or off by timer. The indication of the inclusion of starting the engine by timer is the presence of the label "TIMER" on the key fob display. The system provides two modes of starting the engine by timer. The first mode allows you to start the engine every day in advance set time, the second mode allows you to start the engine periodically, every 2 hours to warm up (or cool the interior in countries with a hot climate). Two modes cannot be used at the same time, the mode you need can be selected by programmable function 2-3 .

To automatically start the engine on a timer in right time(24h) you need to make a reservation for this mode. For this:

In order to turn on or off the engine start by timer every 2 hours, briefly press the buttons II + IV of the key fob. Setting the start time in this mode is not required, the first engine start will occur 2 hours after the mode is turned on.

When the timer engine start is enabled:

When turning off the engine start by timer:

Note: Automatic start of the engine on a timer every 24 hours is useful for starting the engine daily in certain time if your car is parked outside the range of the key fob.

ATTENTION!

The engine start time according to the 24 hour timer can be shifted up to ±2 minutes per day.

TURBO Mode [Button (II+IV)]

If the car has a Turbo - engine, then after long work at high speeds it is not recommended to stop it immediately. The engine should idle for some time to cool the turbine. For this, the SCHER-KHAN MAGICAR V system has a TURBO mode (turbo timer). If the TURBO mode is on, then at the end of the trip the engine will run for 2 minutes. To turn the TURBO mode on or off, briefly press the buttons III + IV of the remote control.

When TURBO mode is enabled:

When turning off the TURBO mode:

To activate the mode at the end of the trip, do the following:

Now you can arm the system. The engine will then run until the expiration of 2 minutes. interval. When the car is armed, the door, hood/trunk sensors, the driver call sensor are immediately armed, and the shock sensor will start working after the engine stops. The engine will be immediately stopped when the door, hood/trunk sensor is triggered, and the system will go into alarm mode. If necessary, you can urgently stop the engine by pressing for 2 seconds. keychain button II.

Auxiliary channel 1 control [Button (II)]

If your car is equipped with an electromechanical hood lock, an additional preheater or other service equipment, you can control the operation of these devices using a key fob. To do this, briefly press button II on the remote control. A short or long signal will appear at the output of additional channel 1 of the processor unit (programmable function 2-5). The siren and parking lights signals will differ when controlling an additional channel, depending on the state of the programmable function 2-5. If a channel is programmed to beep continuously (Programmable Function Value 4 2-5), the system will confirm its activation and deactivation with siren and alarm signals. If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel. The additional channel does not work in the VALET mode and in the alarm mode.

Note: If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel (programmable function 2-5)

Auxiliary channel 2 control [Button (III)]

If your car is equipped with an electromechanical hood lock, an additional preheater or other service equipment, you can control the operation of these devices using a key fob. To do this, briefly press button III on the remote control. A short or long signal will appear at the output of additional channel 2 of the processor unit (programmable function 2-6). The siren and parking lights signals will differ when controlling an additional channel, depending on the state of the programmable function 2-6. If a channel is programmed for a long beep (Programmable Function Value 4 2-6), the system will confirm its activation and deactivation with siren and alarm signals. If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel. The additional channel does not work in the VALET mode and in the alarm mode.

Turning on an additional channel:

Turning off the additional channel:

Note: If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel (programmable function 2-6)

Alarm mode

If the door, hood/trunk is opened in armed mode, the system will go into alarm mode for 30 seconds, alarms and sirens will last 30 seconds. At the end of 30 sec. the system will return to armed mode. If the shock sensor alarm zone is triggered (strong impact), the system will go into alarm mode for 15 seconds, the alarm and siren signals will last 15 seconds. At the end of 15 sec. the system will return to armed mode. When the warning zone of the shock sensor is triggered (weak impact), the system will not go into alarm mode, but will only issue a series of four short signals by the siren and alarm. You can stop the alarm mode by short pressing the button I on the key fob. The locks will not be unlocked, and the system will switch from alarm mode to armed mode.

In alarm mode:

Reminder mode

If the communicator keyfob received an alarm signal from the door, hood/trunk, shock sensor, call sensor and you did not notice it immediately, then the keyfob, after transmitting the alarm signal, goes into reminder mode (short beeps and indication of the zone that caused the alarm mode) . To stop the reminder mode and check the state of the car, briefly press the key fob button IV or button I to exit the security mode and unlock the door locks.

In reminder mode:

Note: Keyfob communicator does not go into reminder mode when receiving a warning signal from a shock sensor (weak impact)

Car Owner Call

If you need to call the owner of the car, tap with a hard object (coin, keys, etc.) near the call sensor. The call sensor LED will flash in green. The function of calling the owner of the car is available immediately after arming. To stop the signals of the key fob-communicator, press the button I of the key fob. To stop the signals from the key fob-communicator and check the condition of the car, briefly press the IV button.

When calling the car owner:

Access to the car without a key fob

Access to a car without a key fob may be required in a number of cases. For example, if the key fob is lost, if the battery in the key fob has run out, if you are relaxing on the beach and do not want to take the key fob with you (the key fob and keys are closed in the car). The SCHERKHAN MAGICAR V system provides such an opportunity. To ensure that only you are allowed access, the system uses a personal code consisting of four digits. The value of each digit of the code can vary from 1 to 9. Thus, the code can have a value from 1111 to 9999. The code is entered and recorded through the call sensor of the car owner.

Recording a personal code:

In order for you to use this function, you must enter your code into the system memory. To do this, follow several steps:

If you made a mistake on any of the steps, then you need to record the code, starting from step 1.

Entering a personal code:

The system allows five attempts to enter the code within 30 minutes. If the code was entered incorrectly, then its entry is blocked for 24 hours or until you disarm the system using the key fob.

Battery protection (out-of-dimension warning)

The SHER-KHAN MagiKar-5 alarm helps protect the car battery from discharge. If you forgot to turn off the parking lights, then when arming, the key fob-communicator will give a series of beeps for 5 seconds. At this time, the images of the lock and side lights will flash on the display. The warning tone will repeat every 30 seconds. three times.

Starter or ignition lock

The system in armed mode will not allow you to start the car engine. When you try to start the engine in armed mode, the system will send an alarm signal to the key fob communicator. The alarm about turning on the ignition will be displayed by flashing side lights on the key fob communicator, sound and vibration signal. The engine blocking operation mode is selected when the system is installed at a service station and depends on the values ​​of two programmable functions 1-4 and 1-8. You can find out more about blocking the engine of your car at the place where the system is installed. When the starter interlock is selected, the system will prevent the vehicle's starter from restarting if the engine is started in automatic mode.

Open door warning

Car alarm SCHERKHAN MAGICAR V warns of an open door (programmable function 1-2). When a custom function value is selected, the alarm flashes if the car door is open.

Protection of the radio channel from code interception

The system has special protection for the commands transmitted by the key fob. Each time you press a button on the system's key fob, the code message changes according to a special algorithm. This is done to protect the system from interception of the code and its selection (intelligent hacking of the security system). The code protection algorithm is specially designed for the SCHER-KHAN MAGICAR system and is unique, not applicable in one security system other brands.

Motor protection in automatic start mode

The system in automatic start mode constantly monitors the operation of the engine. If the engine stops before the end of the warm-up cycle (engine failure or out of fuel), then no later than 20 seconds. processor unit system will turn off the ignition. Repeated automatic start of the engine will not be possible until the malfunction is eliminated. For vehicles with a manual transmission, you must perform the backup mode again.

Shock sensor sensitivity adjustment

You can adjust the sensitivity of the shock sensor depending on your requirements. A regulator is provided to adjust the sensitivity of the sensor. Turning the knob clockwise increases the sensitivity, and counterclockwise decreases it until the sensor turns off. Consult a service station about the location of the shock sensor, it must be easily accessible for adjustment.

Adjusting the sensitivity of the owner's call sensor

You can adjust the sensitivity of the car owner's call sensor depending on your requirements. To adjust the sensitivity on the sensor, a step regulator with three positions is provided. The extreme left position of the regulator corresponds to the minimum sensitivity of the sensor, the extreme right - to the maximum. The sensor should be located in the lower corner of the car's windshield.

Adjusting the volume of siren confirmation signals

You can adjust the volume of the siren's short beeps. To reduce the volume, you need to cut the loop from the wire on the siren's body. The system can be equipped with any siren according to the wishes of the owner, including those where there is no possibility of adjustment.

Backup mode (only for manual transmission)

The standby mode excludes the possibility of automatic starting of the engine if the manual transmission lever is not set to the neutral position. Depending on your requirements, you can choose one of three redundancy algorithms (programmable function 1-6).

Algorithm 1

Algorithm 2

To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, redundancy will be prohibited if the door, hood / trunk are open at the time the ignition is turned off.

Algorithm 3

To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, the implementation of the reservation requires you to each time press button II on the key fob before turning off the ignition (by turning the key in the ignition switch to the OFF position).

ATTENTION!

Close the sunroof and windows before leaving the vehicle. Do not leave people or animals in the vehicle when the reservation mode is being executed.

Do not start the engine automatically if there are people or animals in the car.

Leave the gear lever always in the neutral position. Do not use automatic engine start on open top vehicles.

If the operation of the redundancy mode differs from the described algorithms or does not occur, urgently contact a service station for advice. Until the cause is removed incorrect operation do not use automatic engine start.

PROGRAMMING NEW KEYFOBS

The system can remember the codes of three key fobs. To program new key fobs, follow two steps.

To exit the programming mode, do not take any action for 4 seconds. after writing the code of the last key fob.

If no action is taken after step 1, then after 4 seconds. the alarm will flash 2 times, the system will switch from the key fob programming mode to the VALET mode.

Note:

The SHER-KHAN MagiKar-5 alarm system has three memory cells for storing key fob codes. When you try to write the fourth key fob, the code of the first recorded key fob will be deleted.

PROGRAMMING FUNCTIONS USING THE KEYFOB

Programming the functions of the CTCTS using the key fob consists of four steps.

Note:

If you hear one long siren signal, this means the system has exited the function programming mode. To continue programming, repeat all steps from STEP 1.

ATTENTION!

If you need to change more than one function from the Menu you have selected, then the selection of each function to change must begin with STEP 1.

Menu of programmable functions

Menu #1 [Button (I+II)-]

Note on function 1-4: This function allows you to select the "Panic" mode or JackStop mode (protection against robbery):

Resetting all programmable functions of Menu No. 1 to factory defaults

Menu #2 [Button (I+IV)-]

Resetting all programmable functions of Menu No. 2 to factory defaults

To reset the programmable features to factory defaults, two steps are required.