One of the most popular anti-theft systems is Sherkhan Magikar 5. This is universal equipment. It is compatible with all types of gearboxes. One of the advantages of the Sherkhan Magikar 5 system is its reliability and high efficiency. It uses two-way communication with the car and displays information about its condition on a key fob with a display.
"Sherkhan Magikar 5", the instruction manual for which is included with the purchase, is recognized as one of the best options anti-theft devices. What are the main points to pay attention to? This will help the advice of experienced drivers.
Key Features
The Sherkhan Magikar 5 car alarm, the operating instructions for which should be well studied by the driver before starting its operation, is installed in the engine compartment of the car. This system is compatible with diesel and petrol engines. It is considered universal.
The limitation set by the manufacturer concerns the mains voltage. The wiring must supply 12 V for power.
The message between the vehicle's systems and the user's key fob is transmitted via a two-way radio link. Moreover, the engine starts when a special signal is transmitted from the remote control. You can program a timer.
The signal transmission range is 1.5 km. However, the car should be parked in an open area where it will be clearly visible. In the presence of obstacles, the signal range is reduced.
Advantages
The Sherkhan Magikar 5 alarm, the operating instructions for which must be studied in detail by the driver, has a number of advantages. This explains its high popularity.
System reliability will be ensured by protection high level for all sensors, processor and antenna. Its installation is quite fast. Each owner will cope with this if desired. vehicle.
A powerful siren is installed in the engine department. It is quite loud and has almost no failures in operation. The advantage of the presented system is also the application of high standards in development. The creators of this alarm tested the equipment, which made it possible to bring its reliability to a high level.
The control panel with a display allows the owner of the machine to fully control all functions, as well as easily navigate the system readings. To take full advantage of the alarm, you must carefully study all the recommendations of the manufacturer.
Where to begin?
"Sherkhan Magikar 5", the instruction of which describes in detail the operation process, requires the implementation of all the manufacturer's recommendations. Installation must be carried out by a qualified mechanic. Otherwise, if installed incorrectly, the protective functions of the alarm may be impaired.
To get started with installed system you need to insert the battery into the key fob. It is included in the package, but is not installed in the remote control. This allows you to keep its charge at a high level.
After turning on the key fob, you can start working. To do this, information about the state of the car is displayed. You can manage commands, program the key fob using 4 buttons. Signals are transmitted in a certain encoding. It is unique, so no other remote can control the system. During the operation of the key fob, you can bind it again to the control unit, if for some reason the alarm system has stopped responding to its commands.
Guard mode
Compliance with the rules of work and a responsible attitude of the driver requires "Sherkhan Magikar 5". The instruction manual (autostart and other important modes which are described in detail) allows you to increase the comfort of using the machine.
To begin with, the driver must put the car in security mode. To do this, it is necessary to tightly close all the doors of the car, raise the windows. The trunk is also checked. After that, the driver presses the first button on the key fob. The locks are blocked, the starter will not work.
If the command is completed, the key fob will emit a characteristic sound. The alarm will also beep and the headlights will flash 5 times. The indicator will flicker. This indicates that the system is working. Flickering will occur at a frequency of once per minute. The doors are not hermetically closed, the key fob will emit 3 beeps, as well as the alarm itself. You need to monitor the inclusion of the security mode.
Creating a PIN 1 code
If for some reason the driver cannot use the key fob, the system can be disarmed using PIN 1. It is set by the vehicle owner independently from 2 or 4 digits. Each code element can be set from 1 to 4.
"Sherkhan Magikar 5", the instruction manual of which is studied by the driver, has a certain sequence of setting PIN 1. The equipment is removed from the blocking mode and the car is opened. The ignition key must be turned to the "ON" position, but the engine does not need to be started. Buttons II and IV are pressed on the key fob. A siren will sound once, and headlights will flash.
Within 4 seconds, you need to press any of the buttons. Her number will be registered to the first digit of the code. The same number of beeps will sound. The remaining digits of the code are programmed in the same way. After the procedure is completed, the system will exit this mode. The siren will sound 2 times, followed by 2 headlight flashes.
Disarming
If you turn off the security mode in a standard way does not work (the key fob is lost, not recognized by the system, etc.), it can be removed using the PIN 1 code. This is a simple procedure that was provided by the developers of the Sherkhan Magicar 5 system. The instruction manual describes this process in detail.
The driver opens the car. At the same time, an alarm siren sounds. It is necessary to turn the ignition key three times from the "Off" position. to the "On" position. The sound will stop.
Within 4 seconds, you need to turn the key as many times as the PIN 1 digit the driver programmed earlier. After entering the first code number, the headlights will flash once. Then the second number is entered. When all the code is entered into the system, the lock will be released. Otherwise, the siren will turn on again.
autostart
The driver, if desired, sets up the autorun function, which is embedded in the Sherkhan Magikar 5 system. The user manual for the key fob allows you to configure this mode. To do this, you need to be near the car, close all doors, turn off the security function.
The driver activates autostart. This function will put the machine in security mode on one's own. If the driver forgets to do this in manual mode, after 30 seconds with auto start on, the alarm will block all systems.
Information about the transition to this mode will be sent to the driver's key fob. To do this, the word Passive must be on the screen.
Every 10 seconds, the device transmits a signal to arm the system. This is very convenient if the driver sometimes forgets to block the car.
Other Useful Features
The Sherkhan Magikar 5 alarm system has many useful functions. The instruction manual will allow the driver to select useful modes for himself.
Silent armed mode transmits an alarm signal only to the key fob of the owner of the car. The burglar thinks there is no alarm in the car. This allows you to take it red-handed.
If the driver has small children, you can turn on the safe ride mode. When the car starts moving, all doors are locked.
There is a turbo timer function. This mode allows the engine to run for some more time even when the ignition key is off and the machine is armed. This is necessary for cars with a turbine. This mode increases the duration of the equipment.
Possible malfunctions
The presented alarm system is recognized as one of the most reliable. Its popularity is explained by the mass of useful functions, which are described in detail by the documentation for the Sherkhan Magikar 5 system - the instruction manual. Malfunctions in this equipment are not excluded.
MANUAL
PURPOSE OF THE BUTTONS OF THE KEY FOB-COMMUNICATOR
Example notation:
I - quick (0.5 sec.) button press
I– – long (2 sec.) button press
(I+II) - fast (0.5 sec.) simultaneous pressing of the buttons
(I + II) - - long (2 sec.) simultaneous pressing of the buttons
Number
buttons
Time
pressing
Function (mode)
Enable security mode
Stop alarm mode
Enable starter/ignition interlock
close locks
Disarm
Stop alarm mode
Disable starter/ignition interlock
open locks
Enable/disable the "Free
Turn on/off display backlight
Checking System Status
open trunk
PANIC or JackStop™ modes. For
stop press button I or II
Enable/disable siren signals
Additional management channel 1
Shock sensor enable/disable
Additional management channel 2
Enable/disable timed start
TURBO mode enable/disable
Enter programming menu 1
SCHER-KHAN MAGICAR 5
1)
Factory value. Two step disarming is disabled. For
disarming, just press the button "II" of the key fob
2)
Confirmation of disarming is required. If using the code
PIN1 disabled (programmable function 1-6 in factory setting),
it is necessary to press the button "II" of the key fob again. If used
four- or two-digit PIN1 code (programmable function 1-6
has the value II or III), it is necessary after pressing the button "II" of the key fob
sequentially press four (or two) buttons on the key fob with numbers,
the corresponding digits of the PIN1 code. Only after correct
the second step, the system will be disarmed. If the code is not
entered within 15 seconds or an incorrect code is entered, the system will go
into a state of alarm
Programmable function 1-20: "Auto start
by voltage battery»
to perform an automatic start timer.
This programmable function has two meanings:
1)
Factory value. Automatic voltage start
battery is not used
2)
the battery voltage does not drop below 11.5 V, or
the temperature condition assigned to the programmable
function 1-21
Programmable function 1-21: "Auto start
temperature threshold"
This function allows you to enable or disable the corresponding condition
to perform an automatic timer start, and select
temperature threshold.
This programmable function has four meanings:
1)
Factory value. Automatic threshold trigger
temperature value is not used
2)
The next timed start will be delayed until
the temperature will not drop below -15
C or battery voltage is not
Wanting to understand how to enable autorun on Sherkhan 5, you should study the operating instructions, know the principle of operation and the modes implemented in this car alarm system. It is controlled by using a switching key fob with an LCD display, via a radio channel. Broadcasting of signals is carried out at a distance of up to 1.5 km.
The device is equipped with cars equipped with a gasoline or diesel power unit, with a voltage in the on-board network of 12 W. The alarm system has the option of automatically starting the engine by activating a command from the key fob or starting from a timer.
Preparation for work
How to enable autorun on Sherkhan 5 is presented below, but first the alarm must be prepared for work. Before you start using the key fob, you will need to perform certain actions aimed at its correct activation. The fact is that in order to maintain a full charge of the battery, manufacturers supply the power supply separately from the main device.
To install the battery in the provided compartment, you should carefully remove the latch that holds it in closed position cover of the respective compartment. Usually, this operation does not cause any problems, since the body and other elements of Sherkhan 5 are made of high-quality and high-strength materials.
The next step involves moving the key fob cover opposite to the antenna and placing the battery in the compartment with the polarity observed. After adequate installation of the specified part, a characteristic melodic sound should be heard, after which it is necessary to reinstall the cover and retainer.
Auto start setting
Enabling autorun is described in detail in the presented step-by-step instructions:
Button press modes differ in two ways (important):
- Short-term activation - a single impact on the key, lasting no more than a second, which is accompanied by a short signal;
- Long press - fixing the button for more than 2 seconds until a sound notification appears, after which you can release the key.
Further tuning of the engine excitation programming is shown using functions 1-12 for 25 minutes as an example. First you need to enter the settings mode No. 1, activate buttons 1 and 2 at the same time. Hold them until the remote control beeps. If the manipulation is carried out correctly, the alarm will be in the programming sector.
Next, you need to carry out successive touches of button No. 4 in the amount specified by the program. Each click must be confirmed a specified number of times. In this example, 12 clicks. At the end of activation, you should hold the button for 3-4 seconds, after which, the device will sound 12 notifications to confirm the programming item.
Features on a specific example
The autorun settings of Sherkhan 5 every 2 hours or when the temperature in the cabin drops to -15 ° C, with the cabin warming up for 25 minutes, perform the following manipulations:
- At the same time, buttons I and II are activated, then, pressing VI twelve times, at the end - holding the button III (functions 1-12 are configured taking into account the temporary value of 25 minutes);
- Activators I and II are pressed simultaneously, button No. VI is clicked 13 times (alarm functions No. 1-13 are set to a time indicator of 2 hours;
- Perform pressing simultaneously I + II and VI - 21 touches (function 1-21 is set to a temperature of - 15 ° C).
AT recent times various anti-theft systems are in great demand in the market. One of the most popular systems is the alarm system, which has an optimal ratio of functionality and cost. If you are looking for a really good gadget of this type, then great option will become "Sherkhan Magikar 5".
This device has excellent functionality, and also works reliably and stably. Thanks to the instructions, you can easily learn about the capabilities of this model, as well as learn all the features of operation.
You can easily use Sherkhan Magikar 5 from a distance, because you have a special key fob that is responsible for communication between the user and the security system. The device can work at a distance of up to 1.5 kilometers. The key fob is also equipped with a high-quality liquid crystal display, which makes it easy to read information.
With "Sherkhan Magicar 5" you will be able to activate the motor only on command, which is given by the user through the key fob to the internal timer of the device. When the engine is activated, the temperature in the cabin, the state of the battery and other parameters are neglected.
Device advantages
An important advantage is the versatility of the Sherkhan Magikar 5 alarm, because you can easily install it on cars with any type of gearbox, with engines running on any fuel. The main thing that onboard network was able to generate a voltage of 12 V.
Users like the work of "Sherkhan Magikar 5" due to the fact that this device is really functional. With this device, you can protect a variety of parts of the car. In addition, manufacturers have done a good job of protecting the processor unit, antenna, and all kinds of sensors. They fully comply international standard IP40. All parts of the alarm are mounted directly in your car, while installation does not require much effort and time.
The IP-65 siren, which is equipped with Sherkhan Magikar 5, also works just fine: the signal is powerful, it works in a timely manner. In order for the sound signal to work as correctly as possible, the siren is mounted in the engine compartment of the car. At the same time, you need to make sure that there was no exhaust manifold or high-voltage systems near it.
How to get started
It is worth noting that when buying Sherkhan Magikar 5, there is no battery in the device, since it was placed separately for the most convenient transportation. Thus, the charge will not be consumed even before you begin to use the alarm. For normal operation the battery must be inserted into the correct compartment. To do this, you should remove the fixing plate, which holds the cover of the battery part of the device in a certain position, and then move the compartment cover itself in the direction opposite to the antenna.
Now you can install the battery in its proper place. At the same time, it is important to ensure that the polarity is chosen correctly (it is easy to verify this using graphic indicators). If in doubt, simply install the battery with the negative pole towards the antenna. As soon as the battery is in its place, Sherkhan Magikar 5 will notify you with a sound melody. Now you just have to close the lid and install the latch.
Already during the battery installation procedure, you can make sure that the Sherkhan Magikar 5 is made really high quality, because even to the touch the materials are durable and reliable.
Guard mode
In order to turn on the security mode, you must first turn off the engine and close all doors and trunk of the car. So, you should press the "1" button on the remote control. Immediately after that, the security device itself activates the security mode on all elements of the car: the starter will be blocked until you remove the blocking yourself, and the door locks will also be blocked.
To make sure that "Sherkhan Magikar 5" has successfully switched to armed mode, the system should show you a number of signals:
- One-time operation of the siren;
- Single operation of an emergency light signal;
- The LED indicator will start flashing, the flickering frequency will be 1 time per second;
- Synchronized five-fold blinking of headlights;
- Single short signal from the key fob itself.
Sensor operation
If the indicator light flashes, this means that the security system controls the doors, trunk and other parts of the car through which it can be entered. "Sherkhan Magicar 5" additionally checks all sensors and continuously monitors them, while the motorist can relax, because his car is in good hands!
The device allows you to connect the function of controlling the delay of lighting in the cabin. If it is activated, trigger control will also be performed. Half a minute after the car was put into the armed mode, the shock sensor will start its work.
Warning signals
It is important for the motorist to be vigilant and attentive to the car. For example, in no case should you leave the doors, trunk or hood open. "Sherkhan Magikar 5" will signal you about your inattention with a siren, three times alarm and a three-time signal on the key fob.
To make it easier for you to find the part of the car that you have left open, its image will be highlighted on the display. True, it is displayed on the screen only for 5 seconds, after which it will be replaced by the inscription "FALL", which also indicates the carelessness of the motorist.
If you have activated any sensor, then, unlike other communications of the device, it will not be closed, the security system will allow it to work until the user deactivates it.
Passive Arming
So that you don't forget to arm the device, Sherkhan Magicar 5 can do it automatically. To do this, you just need to change the activation parameter of this function. When automatically arming, it will be activated half a minute after you closed the last door on your car. At the same time, the key fob will constantly signal you that after a specified time the security mode will turn on. If in 30 seconds you open one of the doors, then the countdown will start again. The activation of passive protection is indicated by the inscription “Passive” on the key fob screen.
Alarm mode
"Sherkhan Magicar 5" works without any interruptions and errors, therefore, when the door is opened, the alarm mode is automatically activated, which lasts exactly 30 seconds, and if the cause of the alarm is eliminated, then security system will return to standard mode. If the cause is not corrected, then you will have 8 more cycles of 30 minutes to do this. If even after 4 minutes you could not eliminate the disturbing factor, the security system will automatically switch to armed mode.
Features of signal triggering
In the event that a strong physical impact was made on the machine, and the shock sensor is triggered, it will work for 5 seconds in alarm mode with a strong sound signal and alarm operation. If the physical impact was weak, then the motorist will hear 4 short beeps. So you will always know when someone touched your car or tried to get into it!
Hands-free mode on Sherkhan 5 is designed to automatically arm the car. The anti-theft system is activated when the key fob is removed from the vehicle at a certain distance.
[ Hide ]
How to enable and disable Hands Free?
The instructions for the car alarm provide for two options for the Free Hands Sherkhan 5 mode:
- At a distance of 15 meters from the car. In this mode, the indicator on the screen is in a calm state.
- At a distance of 35 meters from the vehicle. In this case, the "Hands free" indicator will be active on the screen.
"Hands free" indicator on the key fob The designation of the "Free hands" function in the instructions
To change, enable and disable, proceed as follows:
- In order to change the operating mode or remove it altogether, press and hold the I button on the key fob for two seconds.
- To enable/disable the feature free hands Sherkhan 5, you need to hold down the I button on the key fob.
Setting the hands-free mode
How to set the time on the Magikar 5 model?
The Magicar 5 key fob can start the engine using an internal timer. The LCD screen will display the “Timer” icon. In order for the function to work correctly when using it for the first time or after having to remove the batteries, the clock must be set.
According to the manual, the setup is as follows:
- Combined press buttons II and III. The car will beep.
- Press I for less than a second. The time on the screen should flash.
- Using the keys I and II set exact value hours and minutes.
- To fix the set value, leave the programming mode by simultaneously pressing buttons I and II. A signal should sound.
Incorrect time setting leads to desynchronization of the indications on the key fob and on the real clock. Because of this, it is not possible to correctly set the autostart by timer on the alarm. Warming up the engine and interior will be carried out at the wrong time.
You need to set the time in accordance with the real clock, for more accurate synchronization.
Setting the time for Keychain Magicar 5 is shown in the video of the author Marat.
Enabling and disabling the "Turbo" mode on Magikar 5
When operating a car that has a turbocharged engine, special maintenance methods are used:
- To prevent the destruction of the injection mechanism, the car must not be turned off directly after stopping.
- To eliminate the waiting time for the turbine to cool down, a turbo timer is used.
- Signalka Magikar 5 makes it possible to cool the turbine, while not being in the car. The engine runs for about 2 minutes after the trip is completed.
To enable or disable this mode, you must press the keys III and IV for a short time. The state of the function will determine which signals or icons will be displayed on the key fob.
