Sherkhan installation 5. Scher-Khan Magicar V - instruction manual. Arming

Programming the CTCTS functions using a key fob consists of four steps.

1. Enter programming mode and select the programming menu. To enter Menu No. 1, press the I + II buttons simultaneously for 2 seconds. To enter Menu No. 2, press the I + IV buttons simultaneously for 2 seconds. The siren will give one short signal, alarm the car will flash once, confirming the successful completion of STEP 1.

2. Press the IV button to select the Menu function you want to change. The number of presses must correspond to the number of the selected function. For example, to select function 4, you need to briefly press the keyfob button IV four times. Each button press will be confirmed by a short siren sound (if enabled) and a flash of the car alarm.

3. Wait a few seconds. The system will confirm the number of the selected function to be changed with short siren beeps and car alarm flashes. The number of signals will correspond to the number of the selected function.

Note:

If, when choosing a function, you made a mistake with the number of clicks and (or) there are no siren and alarm signals, then you need to repeat all the actions starting from STEP 1.

4. Press the I button to select the factory setting for the function. To confirm this, the siren will give one short signal, the alarm will flash once. Press the II, III, or IV button to select optional function values. To confirm this, the siren will give two, three or four short beeps, the car alarm will flash two, three or four times.

Note:

If you hear one long signal from the car alarm siren, this means that the system has exited the function programming mode. To continue programming, repeat all steps from STEP 1.

ATTENTION!

If you want to change more than one function from the Menu you have selected, then the selection of each function to change must begin with STEP I.

Menu of programmable functions

Menu #1 [Button (I + II)-]

Note on function 1-4: This function allows you to select "Panic" or Jack Stop mode™ (robbery protection):

Resetting all programmable functions of Menu No. 1 to factory defaults

1. Enter programming mode. Press buttons I + II simultaneously for 2 sec. The car siren will sound one short beep and the alarm will flash once, confirming the success of STEP 1

2. Briefly press button III on the car alarm key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time, three siren sounds will sound, the alarm will flash three times, confirming the factory settings of all menu 1 programmable functions.

Menu #2 [Button (I+IV)-]

Resetting all programmable functions of Menu No. 2 to factory defaults

To reset the programmable features to factory defaults, two steps are required.

1. Enter programming mode. Press buttons I + IV simultaneously for 2 sec. The car alarm siren will beep once, the alarm will flash once, confirming the success of STEP 1

2. Briefly press button III on the key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time after this, three siren sounds will sound, the car alarm will flash three times, confirming the factory settings of all programmable car alarm functions of menu No. 2

KEYFOB-COMMUNICATOR CAR ALARM SCHER - KHAN 5

Preparing the key fob-communicator for work

Before using the key fob, you must bring it into working condition, because. during transportation and storage, an insulating gasket is installed between the contact of the battery and the contact plate of the key fob, which prevents the battery from discharging before operation. Before using the key fob, remove it. To do this, release the battery cover lock, press the cover and slide it in the direction opposite to the antenna. Remove the battery. Remove the insulating pad between the battery and the collector plate. Install the battery back, observing the polarity indicated on the bottom of the battery compartment. If there is no indication of the polarity of the battery, then it is set with a negative terminal towards the antenna. Close the battery cover. After that, the keychain is ready to work.

Symbols on the display of the key fob-communicator of the car security system

	Timer start indicator
	TURBO mode indicator
	Passive arming indicator
	"Hands free" mode activation indicator
	Siren indicator
	Shock sensor off indicator
	Vibrating alert indicator
	Indicator of turning on the automatic control of the central lock by ignition
	Door open indicator
	Trunk/hood open indicator
	Shock sensor alarm indicator (optional sensor)
	Car owner call indicator

Sherkhan 5 is the possibility of remote security control using a key fob. The car alarm consists of two components - the switch itself with an LCD display and processor unit built into the car.

[ Hide ]

Description and characteristics

The processor unit connects directly to the car battery and runs on 12 volts. Its main function is driving, receiving and transmitting information from sensors.

The key fob switch is used to control the system by the user. In particular, setting the PIN code, programming functions, as well as turning on and off the car's protection.

The equipment is supplied with an additional key fob and detailed instructions. At the same time, there is a manual for both operation and installation of the system. However, not recommended self-assembly systems. It is better to ask to put it to the car service masters.

Main functions

Key fob-switch is designed for direct impact on the system by the user. It is equipped with four control buttons and a display that displays all the necessary current information.

With it, you can turn the system on and off, as well as program the main unit. The power source is only one AAA battery.

The choice of a particular command is displayed on the screen, and is also accompanied by sound and vibration. The display is backlit automatically when the buttons are pressed, as well as during an alarm.

The functionality of the electronic key fob also includes:

• MAGIC CODE - protection against interception of encoded data;
• display of the current battery level;
• displaying the voltage level of the car battery;
• the possibility of remote engine start, including delayed.

You can also check the temperature in the cabin at this moment and see the current time.

The key fob has a special signal reception range and is able to function at a distance of up to one and a half meters from the car. The processor unit is directly responsible for the protection of the transport and the reaction to pressing the key fob buttons.

Its main functions are:

• automatic engine start on command;
• indication of the delay time for turning on accessories;
• disabling car protection by PIN-code in the absence of a key fob;
• obtaining access to the salon by PIN2;
• control of the car's central lock and trunk lock;
• alarm management;
• the ability to protect the car with the engine running.
• The settings allow you to start the engine in the following ways:
• with a frequency of two, four or eight hours;
• every day at a certain time;
• by analyzing the performance of the car - temperature or voltage.

Another available function is programming the maximum and minimum starter rotation times, as well as setting it to increase with an increase in the number of start attempts.

PIN codes are set by the user and are used for emergency access to the vehicle.

Technical specifications

This system can be built into any car, regardless of the type of engine and gearbox. It is possible to start engines equipped with a turbine.

Alerts are divided into three types:

• sound to the siren - lasts for thirty seconds, sounds continuously;
• optical - power one hertz, also lasts thirty seconds, works on two channels, is emitted intermittently;
• through a radio channel - a range of up to one and a half meters, lasts one hundred milliseconds at a frequency of 0.35 hertz, sounds intermittent.

The exact range of the switch depends on a number of factors, including obstacles, interference, certain weather conditions, and battery level.

The system is managed in one of the following ways:

• remotely using a key fob;
• from the ignition key;
• by triggering the driver call sensor;
• as a response to certain sensor signals.

Electrical circuits are protected by fuses, resistors, and transistors. Additionally equipped with varistors that protect against power surges and interference. The functioning of the system even when the polarity of the power sources is reversed is ensured by diodes.

There are contact sensors that react to opening doors or turning the ignition switch. In this case, the system generates an alarm signal without the possibility of disabling it.

The system also responds to shocks by issuing a signal lasting up to 30 seconds in one cycle. All keyfob radio transmissions occur over a secure channel using special encoding.

The processor unit is characterized by the following parameters:

• work at a voltage of 9 to 18 volts;
• current strength from 20 to 35 milliamps is allowed;
• operates at temperatures ranging from -40 to +85 degrees Celsius;
• the total weight of the device is 270 grams;
• dimensions 150x120x32 mm.

User guide

The system can be configured through the unit or from the key fob. The first is controlled with the help of strokes, and the second - with the buttons. The functionality of the key fob is very wide.

With it, you can:

• set automatic arming;
• stop the alarm mode;
• block the ignition or starter;
• activate the "Free hands" option;
• remotely turn on and off the engine;
• activate the "Panic" mode;
• open trunk;
• connection of the "Turbo" mode;
• program the PIN1 code.

The system block allows you to apply and change PIN2, as well as activate a call to the owner of the car.

PIN code programming

Setting your own PIN1 code takes a few minutes and is not a complicated procedure.

To switch to the programming mode, you need to perform a number of actions:

1. Disable security first.
2. Then open the car door.
3. Turn on the ignition, but do not turn on the engine.
4. Then make a long (about 2 seconds) joint pressing of buttons 3 and 4 on the remote control.

The system will respond with a single beep and flash. However, if you receive a triple beep in response, it means that you have not entered programming mode. Check if you did everything right. It is important that the security mode is disabled, and the ignition, on the contrary, is turned on.

The first digit of the PIN code is given four seconds after the beep. This is done by pressing the key fob button. Its number is equal to the selected number. The selection is confirmed by the appropriate number of beeps and flashes.

The remaining four digits of the code are entered in the same way. They also need to be specified within four seconds. Entering the latter automatically ends the programming mode. This will be indicated by the double sound of the siren and two flashes of the alarm.

After completing the input, you can turn off the ignition and close the car doors.

The PIN2 code is set in the same way:

1. To do this, you need to remove the security mode, open the door and turn on the ignition.
2. Then you need to hit ten times on the call sensor with an interval between hits of less than one and a half seconds. For each hit, the LED will respond with a red indication.

The activation of the programming mode will be accompanied by a fast flashing of the blue LED. Each digit is programmed by strokes. Their number corresponds to the number. One and a half seconds after the input, the input is confirmed. The unit emits the corresponding number of blue flashes, after which it returns to flashing mode.

Enter the rest of the code in the same way. Confirmation of data entry and exit from the programming mode will be accompanied by a single siren sound and a single alarm flash.

Arming

In order to enable the security mode, you must turn off the car ignition and close all doors. After that, a single short press of button 1 on the key fob is performed. Thus, the mode is connected, the starter is blocked and all doors are locked.

Activation of the mode is accompanied by the following indication:

• single siren sound;
• single flashing of the alarm;
• blinking of the indicator with an interval of one second;
• car headlights flashing five times and the closed lock icon on the key fob;
• single switch signal.

The closed padlock icon then lights up and remains displayed until the vehicle is unlocked. From this point on, the system continuously analyzes and monitors the sensor readings. Thirty seconds later, the shock sensor is activated.

If the engine remains on, the installation process guard mode somewhat different. As in the previous case, it is necessary to close all doors and press button 1 on the switch once.

The mode activation indication is similar to the previous case. In this case, the shock sensor will be disabled until the vehicle ignition is turned off. Thirty seconds after the engines stop, the analysis of such signals is turned on.

Button 2 on the key fob is used to disable the security mode.

Keychain - communicator

Before you can start using the key fob, you need to set it up. The first step is to install the power supply.

The symbols on the display show the following information:

• transmitter signal strength;
• battery level;
• clock indicator, as well as the voltage level and temperature in the car;
• state of the lock (open/closed) and security mode;
• disable the shock sensor;
• turning on the vibration signal;
• information about the running timer;
• TURBO mode (enabled/disabled);
• state of the VALET mode;
• display of an open trunk and / or car doors;
• signaling siren;
• inclusion of dimensions;
• visual display of the alarm.

There are also some other symbols representing certain processes.

System check

By pressing the fourth button, you can check the status of the system. The information will be shown on the display.

Cabin temperature Battery voltage

Also, the information is confirmed by a siren and alarm.

Table of signals when checking the status of the vehicle system

Autostart security system

It is possible to automatically turn on the car security system. It can be programmed with a key fob.

In this case, the system will be armed 30 seconds after all doors are locked. At the same time, an appropriate indication and a siren are issued. For another thirty seconds, you can still open the trunk or car doors. If this is done, the auto-on countdown is delayed by another half minute.

If this function is enabled, the PASSIVE indicator will be displayed on the keyfob display.

Auto engine start

The system assumes automatic start of the engine. This is essential in order to maintain certain parameters car, as well as warming up when it is in the parking lot.

Automatic start can be controlled by both sensors and set user timer.

Auto start by battery temperature and voltage

Automatic start of the engine on the machine can occur on a timer or based on the readings of temperature and voltage sensors.

Thus, the number of timer starts is controlled depending on the temperature in the cabin or the voltage level of the car battery. This is configured with a key fob.

The temperature threshold can take one of the following values: -15, -25, +60 degrees Celsius. Restriction according to the voltage level can take only one value - 11.5 volts. Thus, it is possible to adjust the activation of the timer depending on the current parameters of the sensors. This allows you to regulate the temperature of the passenger compartment, as well as maintain the operating voltage in the battery.

Autostart by timer

It is necessary to set the remote autostart of the system by timer in this way: simultaneously press buttons 2 and 4. It is also with their help that the start time is set.

When the timer is turned on, the TIMER indicator on the display lights up, and the engine is controlled according to the time specified by the user.

There are four different engine start modes according to the pre-set timer:

• daily at the specified time;
• periodically, every eight hours;
• every four hours;
• every two hours.

Periodic activation is used to control the temperature in the cabin (heating or cooling the space).

It is possible to install only one mode, it is not supposed to combine them. Setting another behavior automatically disables the previous one.

Turning the engine start on and off according to the timer is accompanied by sound signals and light indication. The display flashes five times.

The exact time of automatic start needs to be specified only for daily switching. In all other modes, the report starts from the moment the function is enabled.

Why the autostart of the Scher-Khan Magicar 5 alarm may not work

If the Sherkhan Magikar 5 autostart system cannot start the engine remotely, the key fob will emit three short beeps. Accordingly, there will be three flashes of the alarm, and after three seconds a series of flashes will occur. This series displays which error has occurred.

Therefore, depending on the number of flashes, you can determine why the engine does not start:

1. If there is one flash, it means that the engine is already on.
2. If two, the ignition is on.
3. If three - opening one of the doors prevents starting.
4. If four - a similar situation, but with a trunk or hood.
5. In the event that the system responded to you with five flashes, the start reservation for the car in manual transmission has not been made.

If the remote engine start does not work, the system will try to start it again. In the event that this fails to be done three times in a row, the alarm will go into standby mode. If this happens, then the car will no longer start, you must contact service center to determine the cause of the problem.

Video "Autostart stopped working"

What to do if the car does not start from autorun is described in the video from Seryoga.

Excellent operational characteristics and the "Sherkhan Magikar 5" alarm system has high reliability. The instruction manual gives a detailed explanation about the principles of using this device and its main functions.

purpose

The instruction "Sherkhan Magikar 5" indicates that this alarm can be controlled by the user remotely, which is helped by an exclusive keychain communicator. The display is made of liquid crystal material, so it is considered particularly reliable.

A specially built-in system regulates a single mechanism of interaction between the processor unit and the key fob-communicator. You can control the alarm from a distance of 1500 m.

The engine starts after a special command is given. It is usually sent along the key fob, the outer part of the device, the internal timer. This does not take into account the temperature in the car, and the voltage level of the battery is also unimportant.

Advantages

Preparing the key fob for work

Before using the key fob, you need to perform several manipulations, since there is no battery in it during transportation. It is located separately, and not in the proper compartment. This is necessary to conserve battery power. in full. When you remove the battery, no power is consumed, so there is no need to additionally recharge the device.

To place the battery in the right place, carefully remove the latch that holds the Sherkhan Magikar 5 battery cover in its original position. In this case, malfunctions are excluded, since all structural elements are made with maximum quality. This applies to both cutting parts and the material from which they are created.

After performing this action, it is necessary to move the cover itself to the side that runs opposite to the protruding antenna. The battery for power should be carefully installed in the compartment. As with any battery, polarity is provided here, so the position of its sides can only be determined after familiarizing yourself with the graphic pattern near this compartment.

If any indicators are missing, then the Sherkhan Magikar 5 signaling is placed with a minus sign in the direction where the antenna is located. After correct installation a characteristic melody is heard, which indicates the completion necessary action for the correct operation of the system. You only need to close the battery storage compartment cover, and then install the appropriate lock on it.

Arming

To activate the security mode, you must first turn off the ignition, and close all compartments of the car to ensure the free operation of "Sherkhan Magikar 5". The operating manual determines that the button number 1 on the key fob is then pressed with only one touch. It is not necessary to hold it for a long time, a point and moderate touch is enough. The system will automatically translate everything necessary elements machine in guard mode. The existing locks on the doors will be blocked, the starter will not work until the owner himself removes this mode.

When the car alarm "Sherkhan Magikar 5" is armed successfully, a person can trace some signals:

1. The siren will sound once with a moderate whistle.
2. The emergency light signal will also make itself felt once.
3. An LED indicator will turn on, which will show that the car is under protection by means of measured flashing at a frequency of 1 time per second.
4. The headlights flash five times simultaneously. Further, the image of the closed lock will remain lit until the car is unlocked, and the headlights will go out.
5. The key fob will give only one short signal.

Enable sensors

When the LED begins to flash steadily, this means the activation of the system control over the state of all possible inputs and methods of penetration into the car, which the Sherkhan Magikar 5 cannot allow. The instruction manual reports that even the sensors for calling the owner and ignition control are additionally checked and constantly monitored, which allows the owner to calmly do any of his business at this time.

If connected additional function, which is responsible for regulating the delay of the cabin light, will also provide for the control of triggers, which usually do not begin to be guarded immediately, but only after a certain amount of time has passed. activates work 30 seconds after the machine has been armed.

A warning

The instruction "Sherkhan Magikar 5" warns users against inattention to the car. Shouldn't be left open doors, hood and luggage compartment. If this happens, then the person suddenly, instead of the usual behavior of the car when arming, hears a three-time key fob signal along with a siren. In this case, the alarm also flashes three times at once.

On the display, you can see the image of the item that the owner of the car forgot to close. This happens only for five seconds, so the user may not have time to see the desired item. At the same time, the text FALL appears on the display. This is a direct indication that you should find an unclosed element and cover it tightly.

"Sherkhan Magikar 5" instruction manual defines as a device upper class, since it sets all vehicle communications on guard, but it bypasses the activated sensor. It will automatically be additionally protected after the owner closes it. The hood area is not reflected in common panel, as it refers to the trunk area.

Automatic transition to armed mode

Passive arming is a separate feature that can be enabled or disabled for Sherkhan Magikar 5. The autorun instruction provides - you just need to change the state of the selected function. If the owner decides to activate just such a mode, then immediately after the last door is closed, the timer is activated, and the security is turned on after 30 seconds.

When the countdown is started, the system constantly sends warnings that this mode will turn on. This happens every 10 seconds. If any door is opened at the specified time, the system will activate the armed mode at the countdown of 30 seconds after the last door is closed. You can see if this function is working by the word PASSIVE, which is always shown on the display in this case.

Alarm mode

When Sherkhan Magikar 5 is operating, malfunctions are unacceptable. When any door is opened, the system will automatically be in alarm mode for exactly 30 seconds. When this time is over, it will return to the standard state again.

If the cause that caused the alarm has not been eliminated by this time, the signal will sound every 30 seconds and last for half a minute. This cycle is repeated eight times. If even then the reason for the violation of the usual mode is not canceled, the system returns to the armed mode, but on condition that the active sensor is bypassed.

Features of work

If the shock sensor is triggered, that is, there is a strong impact on any part of the car, the Sherkhan Magikar 5 alarm will be in alarm mode for 5 seconds, during which a strong signal from the siren and alarm is given.

With a weak impact, that is, the activation of the warning zone, also regulated by the shock sensor, 4 short ones will sound, which are generated by the Sherkhan Magikar 5 car alarm. There were no malfunctions in this process, so the owner of the device can be confident in his own technique.

Many users appreciate the ease of use of Sherkhan Magikar 5. How to disable security mode? With a short one-time press on the key fob button number 2. If you correctly program all the functions of the device, the alarm will become a reliable assistant in ensuring the safety of the car.

Example notation:

I - quick (0.5 sec.) button press

I - long (2 sec.) button press

(I + II) - fast (0.5 sec.) simultaneous pressing of the buttons (combination of buttons)

(I + II) - long (2 sec.) simultaneous pressing of the buttons (combination of buttons)

Note:

With a long 2 sec. pressing the I button, the car alarm operation modes are sequentially changed in the order (1) > (2) > (3) > (1) .... In mode (2) the "Hands-free" function has a long working range - the symbol flashes.

Setting the time on the keyfob-communicator display

Setting the current time is required before starting the operation of the system or when changing the key fob battery. Follow the steps according to the table below.

ATTENTION!

Setting the correct time is necessary condition for correct operation automatic start of the engine by timer.

Setting the key fob-communicator modes.

Vibration call, owner call, temperature display standard "°F" or "°C"

To set the desired operation mode of the car alarm key fob, follow the steps in accordance with the table below.

Hands-free mode on Sherkhan 5 is designed to automatically arm the car. The anti-theft system is activated when the key fob is removed from vehicle for a certain distance.

[ Hide ]

How to enable and disable Hands Free?

The instructions for the car alarm provide for two options for the Free Hands Sherkhan 5 mode:

1. At a distance of 15 meters from the car. In this mode, the indicator on the screen is in a calm state.
2. At a distance of 35 meters from the vehicle. In this case, the "Hands free" indicator will be active on the screen.

"Hands free" indicator on the key fob The designation of the "Free hands" function in the instructions

To change, enable and disable, proceed as follows:

1. In order to change the operating mode or remove it altogether, press and hold the I button on the key fob for two seconds.
2. To enable/disable the feature free hands Sherkhan 5, you need to hold down the I button on the key fob.

Setting the hands-free mode

How to set the time on the Magikar 5 model?

The Magicar 5 key fob can start the engine using an internal timer. The LCD screen will display the “Timer” icon. In order for the function to work correctly when using it for the first time or after having to remove the batteries, the clock must be set.

According to the manual, the setup is as follows:

1. Combined press buttons II and III. The car will beep.
2. Press I for less than a second. The time on the screen should flash.
3. Using the keys I and II set exact value hours and minutes.
4. To fix the set value, leave the programming mode by simultaneously pressing buttons I and II. A signal should sound.

Incorrect time setting leads to desynchronization of the indications on the key fob and on the real clock. Because of this, it is not possible to correctly set the autostart by timer on the alarm. Warming up the engine and interior will be carried out at the wrong time.

You need to set the time in accordance with the real clock, for more accurate synchronization.

Setting the time for Keychain Magicar 5 is shown in the video of the author Marat.

Enabling and disabling the "Turbo" mode on Magikar 5

When operating a car that has a turbocharged engine, special maintenance methods are used:

1. To prevent the destruction of the injection mechanism, the car must not be turned off directly after stopping.
2. To eliminate the waiting time for the turbine to cool down, a turbo timer is used.
3. Signalka Magikar 5 makes it possible to cool the turbine, while not being in the car. The engine runs for about 2 minutes after the trip is completed.

To enable or disable this mode, press the III and IV keys for a short time. The state of the function will determine which signals or icons will be displayed on the key fob.