Wanting to understand how to enable autorun on Sherkhan 5, you should study the operating instructions, know the principle of operation and the modes implemented in this car alarm system. It is controlled by using a switching key fob with an LCD display, via a radio channel. Broadcasting of signals is carried out at a distance of up to 1.5 km.
The device is equipped with cars equipped with a gasoline or diesel power unit, with a voltage in the on-board network of 12 W. The alarm system has the option of automatically starting the engine by activating a command from the key fob or starting from a timer.
Preparation for work
How to enable autorun on Sherkhan 5 is presented below, but first the alarm must be prepared for work. Before you start using the key fob, you will need to perform certain actions aimed at its correct activation. The fact is that in order to maintain a full charge of the battery, manufacturers supply the power supply separately from the main device.
To install the battery in the provided compartment, you should carefully remove the latch that holds it in closed position cover of the respective compartment. Usually, this operation does not cause any problems, since the body and other elements of Sherkhan 5 are made of high-quality and high-strength materials.
The next step involves moving the key fob cover opposite to the antenna and placing the battery in the compartment with the polarity observed. After adequate installation of the specified part, a characteristic melodic sound should be heard, after which it is necessary to reinstall the cover and retainer.
Auto start setting
Enabling autorun is described in detail in the presented step-by-step instructions:
Button press modes differ in two ways (important):
- Short-term activation - a single impact on the key, lasting no more than a second, which is accompanied by a short signal;
- Long press - fixing the button for more than 2 seconds until a sound notification appears, after which you can release the key.
Further tuning of the engine excitation programming is shown using functions 1-12 for 25 minutes as an example. First you need to enter the settings mode No. 1, activate buttons 1 and 2 at the same time. Hold them until the remote control beeps. If the manipulation is carried out correctly, the alarm will be in the programming sector.
Next, you need to carry out successive touches of button No. 4 in the amount specified by the program. Each click must be confirmed a specified number of times. In this example, 12 clicks. At the end of activation, you should hold the button for 3-4 seconds, after which, the device will sound 12 notifications to confirm the programming item.
Features on a specific example
The autorun settings of Sherkhan 5 every 2 hours or when the temperature in the cabin drops to -15 ° C, with the cabin warming up for 25 minutes, perform the following manipulations:
- At the same time, buttons I and II are activated, then, pressing VI twelve times, at the end - holding the button III (functions 1-12 are configured taking into account the temporary value of 25 minutes);
- Activators I and II are pressed simultaneously, button No. VI is clicked 13 times (alarm functions No. 1-13 are set to a time indicator of 2 hours;
- Perform pressing simultaneously I + II and VI - 21 touches (function 1-21 is set to a temperature of - 15 ° C).
MANUAL
PURPOSE OF THE BUTTONS OF THE KEY FOB-COMMUNICATOR
Example notation:
I - quick (0.5 sec.) button press
I– – long (2 sec.) button press
(I+II) - fast (0.5 sec.) simultaneous pressing of the buttons
(I + II) - - long (2 sec.) simultaneous pressing of the buttons
Number
buttons
Time
pressing
Function (mode)
Enable security mode
Stop alarm mode
Enable starter/ignition interlock
close locks
Disarm
Stop alarm mode
Disable starter/ignition interlock
open locks
Enable/disable the "Free
Turn on/off display backlight
Checking System Status
open trunk
PANIC or JackStop™ modes. For
stop press button I or II
Enable/disable siren signals
Additional management channel 1
Shock sensor enable/disable
Additional management channel 2
Enable/disable timed start
TURBO mode enable/disable
Enter programming menu 1
SCHER-KHAN MAGICAR 5
1)
Factory value. Two step disarming is disabled. For
disarming, just press the button "II" of the key fob
2)
Confirmation of disarming is required. If using the code
PIN1 disabled (programmable function 1-6 in factory setting),
it is necessary to press the button "II" of the key fob again. If used
four- or two-digit PIN1 code (programmable function 1-6
has the value II or III), it is necessary after pressing the button "II" of the key fob
sequentially press four (or two) buttons on the key fob with numbers,
the corresponding digits of the PIN1 code. Only after correct
the second step, the system will be disarmed. If the code is not
entered within 15 seconds or an incorrect code is entered, the system will go
into a state of alarm
Programmable function 1-20: "Auto start
by voltage battery»
to perform an automatic start timer.
This programmable function has two meanings:
1)
Factory value. Automatic voltage start
battery is not used
2)
the battery voltage does not drop below 11.5 V, or
the temperature condition assigned to the programmable
function 1-21
Programmable function 1-21: "Auto start
temperature threshold"
This function allows you to enable or disable the corresponding condition
to perform an automatic timer start, and select
temperature threshold.
This programmable function has four meanings:
1)
Factory value. Automatic threshold trigger
temperature value is not used
2)
The next timed start will be delayed until
the temperature will not drop below -15
C or battery voltage is not
To set autorun with Scher-Khan keychain magicar 5, press button 2 on the key fob and hold it down for more than two seconds. With this manipulation, the car will be set to armed mode with the engine running, the doors will be locked, and after that the engine will be started. If the engine is started successfully, then the key fob will display information about how much time is left for the engine to run before stopping (it is most convenient if the time interval is programmed in minutes - from 5 to 45 minutes). If the launch has taken place, then in the distance you can see light smoke from the exhaust pipe.
To start a trip, during the set autostart interval, when it has not yet expired, open the driver's door, insert the ignition key into the lock and switch it to the position that corresponds to the inscription on the ignition on. All these actions must be done in no more than 20 seconds, if you delay in time, the ignition will not turn on and the engine will be turned off. As you understand, this is provided to prevent malicious attempts to steal your car.
If the launch fails, the Sherkhan Magikar 5 system will make a second and then a third attempt to start the engine. If all three attempts to start did not take place, then the security system will stabilize in standby mode. To re-initiate the autostart function, you must first make sure that the engine is working.
Why autorun Scher-Khan magicar 5 does not work
Possible reasons for autorun failure are as follows:
- discharged battery;
- the temperature outside the window in winter has reached a critically low level (preventing the easy operation of this function);
- other ICE systems could malfunction, making it difficult to start the engine;
- car electrical failure
- problems are related to the immobilizer, which prevents autorun;
- the indicator shows smoke, although the engine did not start, so the system does not attempt to start 2.
If, when the key is flogged, the ignition works, and the auto start from a distance does not work, then you need to reprogram it, you can try to do the following - make the start periods shorter and set the response temperature higher.
How the Sherkhan Magikar 5 alarm works during launch:
When it is not possible to set to autorun:
- with the ignition off;
- if not all car doors are closed;
- if the motor is already running;
- in cars with mechanical transmission - if the "redundancy" mode is not active.
If a remote start produced successfully, the corresponding systems behave as follows:
When the engine is automatically stopped, the systems behave as follows:
How to set the warm-up interval for autorun Sherkhan Magikar 5
To get started Scher-Khan installation magicar 5 in time, simultaneously with two fingers, press the first and second buttons on the key fob and hold the buttons like that for some time. (The autostart interval is possible 2, 4 or 6 hours - which specific value to choose depends on the condition of the battery and engine.)
1. Briefly press the Roman buttons 2 and 4 once without holding them down - this will turn off the timer.
2. Press the Roman button 4 13 times (after each pressing, the siren will confirm), then wait until the siren confirms the received signals 13 times.
3. It remains to select the autorun interval: to set autorun after two hours, press the Roman button 4, so that after 4 hours, press the Roman 3, after 8 hours, press the Roman 2.
4. Finally, finish the auto-start setting by turning on the timer by pressing Roman buttons 2 and 4 once and immediately releasing them.
How to set autorun Sherkhan Magikar 5 by temperature in the cabin
1. First, in a way already known to us, you need to turn on the autorun mode by time - to do this, press button 4 13 times (after each press, the siren will confirm), and then wait until the siren confirms the received signals 13 times.
2. Switch to programming mode. To do this, simultaneously press two fingers on the first and second buttons on the key fob and hold the buttons like that for some time.
- Deactivate the timer (if it is not already off) by briefly pressing buttons 2 and 4 simultaneously.
- Press 21 times on the Roman button 4 - the siren should turn on.
- Wait until the siren sounds 21 times, and then proceed to the temperature selection.
- To turn on autostart at minus 25°С, press button 3, at minus 15°С, press button 2.
- Restart the timer? by pressing buttons 2 and 4.
How to program the warm-up duration
The warm-up time on the Sherkhan Magikar 5 alarm can be selected in the form of specific time periods in minutes (5, 15, 25 or 45 minutes).
- First you need to turn on the programming function by simultaneously long pressing buttons 1 and 2.
- Press button 4 12 times, each press will be accompanied by an audible confirmation, and the final confirmation of programming is 12 siren sounds in a row.
- It remains to set the warm-up time. To warm up for 45 minutes, press button 4 to 25 minutes. – button 3, 15 min. – button 2 and 5 min. – button 1.
How to program autostart by on-board voltage
You can program auto start, in case the battery is discharged to 11.5 volts.
- Enter the time trigger mode by pressing button 4 13 times.
- Activate the programming function by simultaneously long pressing buttons 1 and 2.
- Press button 4 20 times without stopping, after which the siren will also sound 20 times.
- Press button 2 - in this way you will turn on the autorun operation mode by battery voltage.
The most common problems with autorun
- The “Valet” mode is activated when the car is urgently disarmed (zzzz signs appear on the key fob). To solve the problem, you need to, with two fingers at the same time, press buttons 1 and 3 for more than 2 seconds.
- When the ignition is off, the car does not stall. The doors are locked, and in order to deactivate autorun, you need to activate the car's doors. To get out of this situation, you need to use button 2 to perform functions from 1 to 16. To turn off the engine, you must turn the ignition key to the "Ignition Off" position.
- If you urgently need to remotely turn off the engine when autostart is running, then press button 2 and hold it.
Video: Setting up the autostart alarm Scher Khan magicar 5 on a manual transmission
Video: The car does not start with the Scher Khan magicar 5 alarm. Finding the cause
If the video is not showing, refresh the page or
Like on a Sher alarm Khan Magicar 5 to set auto start of the engine by temperature?
- it only has a start on the discharge of the battery !!!
- Attention! It is not possible to automatically start the engine only by temperature or only by low battery voltage. The time trigger enable condition is mandatory.
Attention! During programming, the system must be disarmed and the ignition in the car must be turned off. Also disabled mode Free hands and preferably the door is open so that there is no re-arming during programming.
1) Timed autostart setting (every 2, 4 or 8 hours)
b) To activate the timed autostart mode, press the IV button 13 times in succession (the siren emits a beep after each button press; that is, press once, we hear a beep, press a second time - we hear a beep and so on 13 times)
c) Wait for the siren to beep 13 times in a row.
d) Then select the desired autorun time button II - 8 hours, III - 4 hours or IV - 2 hours.2) Setting autostart by temperature (when t is reached in the cabin -15, -25, +60)
For the autostart to work correctly when the temperature is reached, 3 steps must be performed:
2. Turn on temperature control (mode 1-21 in II, III or IV)
a) Recall that the entry into the function programming mode is carried out by long pressing the I + II buttons.
b) To activate the autostart mode by temperature, press the IV button 21 times in succession (the siren beeps after each button press; that is, we press once, we hear a beep, we press a second time - we hear a beep and so on 21 times)
c) Wait for the siren to beep 21 times in a row.
d) Then choose required temperature autorun button II - (-15), III - (by -25) or IV - (+60).
e) After that, you need to turn on the timer from the key fob. Press simultaneously II + IV briefly, the display will show the inscription “timer”. If it was activated (lit) before programming, it must be switched off (also II+IV) and switched on again.3) Autostart setting by on-board voltage
The implementation of the delay of the timer start up to the moment when the battery is discharged to 11.5 V is carried out as follows:
1. Enable time trigger (mode 1-13 in II, III or IV) see 1) a), b), c)
a) Entering the function programming mode by long pressing the I+II buttons.
b) To activate the voltage autostart mode, press the IV button 20 times in succession (the siren beeps after each button press; that is, we press once, we hear a beep, we press a second time - we hear a beep and so on 20 times)
c) Wait for the siren to beep 20 times in a row.
d) This will enter the programming mode of the function Limit timer starts by battery voltage.
e) After that it is necessary to press button II to activate the mode.Engine warm-up time:
To set the engine warm-up time, set function 1-12 to position II.
In more detail, you need to do the following:
a) Entering the function programming mode is carried out by long pressing the I + II buttons.
b) To set the engine warm-up time, press the IV button 12 times in succession (the siren beeps after each button press)
c) Wait for the siren to beep 12 times in a row.
d) Then select the desired duration of the start button I - 5 minutes, button II - 15 minutes, III - 25 minutes or IV - 45 minutes.Make sure the system is disarmed and lit before programming.
- You set the desired temperature by programming the center. block and on the keychain you put the start on a timer, it seems like this.
When installing a modern and multifunctional alarm system on a car, you need to understand the procedure for using and possible mistakes. Such systems include the Sherkhan 5 alarm system. It is also important to entrust the initial installation and debugging of work to professionals.
Purpose of the alarm
car alarm Sherkhan Magikar 5 belongs to the category of devices with signal control through a separately dedicated radio channel. Mutual communication between the key fob-communicator of the user and the process control unit is distinguished by the possibility of signal transmission over a distance of up to 1.5 km.
The system, taking into account its high functionality, performs a number of security operations:
- engine blocking with protection of system components;
- engine autostart with the possibility of taking into account individual parameters;
- sound accompaniment of security siren hidden from access.
The main functions are feasible through the implementation of auxiliary operations that can be activated by the user.
All functions of the security system
Even correct installation does not allow you to use possible functions without debugging and testing them. Therefore, you should carefully study all the provisions Magicar instructions 5. Separately, you should consider the possibilities of the key fob, processor unit and some technical parameters.
Key fob functionality
The device has a liquid crystal operating screen and is made in one housing with 4 control keys. Among the main functions are:
- Security code . Using Sherkhan 5 Magic Code, all signals are protected during transmission.
- Control of executed commands through audio and video support.
- Discharge level indication Car battery.
- Engine run time display after autostart, current time.
- Running engine reminder.
- Interior temperature display cars.
- Reminder of received alarm messages.
- Manual remote motor start symbol.
- Processor operating functions
When interacting with the remote control, the Scher Khan Magicar 5 alarm processor generates the following commands:
- engine starting in automatic mode when specifying one of the two options for the transmission unit (automatic transmission or "mechanics");
- setting offline start interval(2, 4, 8 or 24 hours) or conditions (when certain temperature in the cabin or antifreeze);
- issuing a command to force the engine to start;
- engine stability control;
- setting the algorithm for starting the motor, taking into account the features - the type of engine, starter operation time, etc.;
- task of personal identification codes for signaling scher if the key fob or key is lost;
- the ability to set the auto protection mode after starting the engine, priority unlocking the driver's door;
- performance of service functions: light off delay, automatic arming of the car - "without key fob".
Such a wide functional range would not have been possible without the task of excellent technical abilities.
All technical features
To perform its functions, the security system uses several methods to protect electrical networks:
- installation of slow-acting fuses taking into account the connection scheme;
- using internal combustible resistors when the current is exceeded;
- installing internal transistors;
- using directional diodes in case of a change in the direction of the current;
- installation of varistors for protection against voltage surges or when creating impulse noise.
The alarm has a wide operating temperature range (-40°C - +50°C), low current consumption (no more than 35 mA in standby mode) and a small unit weight - 270 g. Such indicators indicate a well-thought-out and effective system.
In the alarm mode, the Sherkhan 5 alarm system can work in one of three ways:
- sound siren (continuous signal, duration 30 seconds);
- optical signal(triggered by an alarm, the sound is intermittent at a frequency of 1 Hz for 30 seconds);
- radio signal(the time interval of the sound notification is 100 seconds, the sound itself is intermittent with a frequency of 0.35 Hz).
At the same time with general protection vehicle operating instructions indicate the presence of additional protection barriers, in particular:
- Objects under protection. Sensors for controlling the opening of doors, trunk, hood, impact. When you try to open, an alarm sounds (30 seconds) with the impossibility of turning off after arming.
- Radio communication channel with the system. Provides constantly changing coding of the transmitted signal.
Food for consumers is provided by the following sources:
- Processing unit- car battery - 12V.
- key fob switch- built-in battery class "AAA" - 1.5V.
- Keychain– 2 built-in batteries of class “CR2025” – 6V.
For customizing operating modes and full use security system you should remove the protection against the discharge of the battery of key fobs, and get acquainted with the symbols and purpose of the buttons. If the key fob does not work, the gasket between the contact and the battery is removed. The beginning of the work will be a confirming characteristic melody.
Using key fobs Sherkhan 5
The functionality of the switch corresponds to the symbols specified in the operation manual and is expressed in the following positions:
- low battery indication and switch to power-saving mode;
- auto parameter status display- battery voltage, interior temperature, current time;
- Valet mode indicator;
- guard mode symbol, unlocking and locking locks;
- sound indicator;
- display of disabled shock sensor;
- vibration alert enabled;
- using passive arming;
- activating hands-free mode;
- indication open doors or hood;
- engine start display or using the ignition lock;
- indication of the included parking lights;
- active timer start mode;
- Turbo mode activation;
- call sensor activation;
- alarm mode display when the secondary shock sensor is triggered.
For effective use of all possibilities, you will need to deal with the question of how to configure and how to enable individual functions. Programming is carried out from a key fob with 4 working buttons. To facilitate the order of use, you should assign serial numbers to the keys:
- Lock button– I.
- Key with open lock and key– II.
- open trunk– III.
- Question mark - IV.
Correct work Scher car alarms khan is possible only in the case of the task of the correct time. This is required when using the alarm for the first time or after changing the batteries.
Installation is carried out according to the following algorithm:
Step 1. Press the combination of buttons II + III, hold for 2 seconds. The programming mode is called.
Step 2. Press the I button, hold for half a second. The mode for changing the current time is activated.
Step 3. Press the I button again, hold for half a second. Set the clock rate.
Step 4. Press button II, hold for half a second. Set the minutes.
Step 5. Press the combination II + III, hold for 2 seconds. We exit the programming mode (confirmed by sound).
Only when the time is set, it becomes possible to link the alarm to the engine start by timer.
Further configuration is related to the activation of operating modes. To learn how to program the work, you should study the following algorithm:
Action 1. Press the II + III buttons, hold for 2 seconds. The programming mode is activated.
Action 2. Press button III, do not release 0.5 sec. The vehicle call mode becomes available. Confirmed by the appearance and symbol of the lifted handset.
Action 3. Press and hold the IV button for half a second. The key fob vibration mode is called.
Action 4. Press the combination I + IV for 0.5 seconds. Change the temperature format.
Successful execution of the second step will occur when the functions are activated no later than 15 seconds after the end of step 1.
When using key fobs in the dark, the backlight is activated by briefly pressing the "III" key. In the same way, the backlight turns off.
Now the alarm is ready to work, but for correct operation, you should study some questions on how to use individual modes.
Alarm operating modes
Regular use of the alarm brings all the actions of the owner to automatism. But on initial stage you need to find out all the nuances of individual operating modes.
Arming and passive mode
The main operating mode is arming the machine. Its activation should be carried out with securely locked doors and hood and trunk lids. In this case, press the "I" key. Successful action will result in:
- For siren signal- single signal.
- For alarm - one-time flash.
- Built-in LED- runs at a frequency of 1 time per second.
- Switch Display- 5-fold blinking of the "headlights" of the car with the transition to the indicator of the closed lock.
- Key fob signal- a single beep.
In the future, the system will automatically put the following components into operation:
- door, hood and trunk sensors;
- shock sensor - 30 seconds after the start of work.
When operating the alarm, it should be taken into account that if one of the doors is not tightly closed, the protection is activated bypassing the sensor of the marked element. In this case, the ignition is still blocked. In the future, working capacity in full protection mode is easily restored.
When using the light delay function in the cabin, you should program the function to delay the start of arming the car for this time.
The need to protect a car with a running engine arises when the car warms up, leaves the passenger compartment for a short time (if it is necessary to open the gate, etc.). The function is programmed by activating the "Passive" command under index 1-5. The start of passive protection is accompanied by the same inscription on the display of the switch.
Alarm message
When an intrusion attempt is made, the alarm goes into alarm mode. This is expressed in the following manifestations:
- Sound signal and emergency– works within 30 seconds.
- Internal indicator- blinking with a frequency of 1 second.
- Display - the symbol blinks according to the cause of the alarm.
- Key fob operation - initial intermittent signal (30 sec.) followed by a reminder every 2 sec.
The system is transferred to the armed mode by pressing the "I" or "II" buttons, or there is an automatic transition after the first 30 seconds of the alarm. If the factor continues to be affected, the alarm mode will be used 8 more times. When the shock sensor is activated, the alarm state lasts for 15 seconds according to a similar algorithm.
Disarming
In the normal disarming mode, the II key is used. Process completion confirmation is accompanied by:
- For siren signal- double signal.
- For alarm- double flash.
- Built-in LED stops working.
- Switch Display- 5-fold blinking of the "headlights" of the car with an indication of an open lock.
- Key fob signal– 2x short beep.
Safe mode involves entering a PIN code after pressing the "II" key once and using it again. This feature is activated via the setting mode function with index 1-19. Activating channel 2-11 allows you to use the function step by step opening doors.
Remote start mode
The engine is started for warming up by pressing the "II" button for 2 seconds. In this case, the car is armed and the engine starts. The keyfob-switch reports the time until the engine stops in the reverse timer mode.
To answer the question of how to reset the engine run time, use the programming mode (function 1-12). The warm-up time is set in the range of 5-45 minutes in increments of 10 minutes.
Additional features
Among additional features It should be noted:
- Panic mode. Activated by pressing the IV button for 2 sec. and stops the engine from starting automatically. After 90 seconds, the system switches to the standard armed mode.
- Jack stop mode. It involves stopping the engine forcibly (even while driving). It is set as an alternative to the "Panic" mode through a task in the "Programming" section. Both modes are canceled after a short use of buttons I or II.
- Valet mode. Allows you to not use the door lock. This function is used when visiting a car service. The I+III buttons are shared for 2 seconds.
- Remote start timer. Used when the engine needs to warm up.
The mode is activated according to the following algorithm:
Step 1. Press the combination of buttons II + III (hold for 2 seconds). The programming mode is activated.
Step 2. Press and hold for 0.5 seconds. button II. Go to the timer setting mode.
Step 3. With the I button we change the hours, with the II button we set the minutes.
Step 4. We exit the mode using the II + III combination (press, hold for 2 seconds).
If you need to turn on the function, or if a question arises - how to turn off the timer, they equally use a short press of the buttons II and IV.
Violations of normal operation
Operating experience allows us to call Sherkhan 5 reliable signaling- at the level of Starline A8 and Starline E90. However, some malfunctions still occur during the operation of the equipment:
- Sensor failure. One of the most common causes is wire breakage, contact damage.
- Disruption in work Valet mode . When activated, the system does not close the doors.
- Refusal to execute commands from the key fob. If the battery is in good condition, the failure may be caused by damage to the antenna.
In the event of a complete failure to work, allow the most simple reasons failure. You should not be interested in how to flash the system again before checking the power supply to the processor.
To correct failures, comments and reviews on the forums do not always help. If a possible ways eliminations have been used, and the malfunction has not been eliminated, the restoration should be entrusted to specialists. Preliminary specify the malfunction and you will be answered how much the repair costs.
With the timely diagnosis of problems, the car will always be under reliable protection.
