Scher-Khan car alarm programming. Scher-Khan Magicar V - user manual Car alarm Sherkhan 5 manual

How to set the temperature auto start of the engine on the Sher-Khan Magicar 5 alarm?

1. it only has a start on the discharge of the battery !!!
2. Attention! It is not possible to automatically start the engine only by temperature or only by low battery voltage. The time trigger enable condition is mandatory.

   Attention! During programming, the system must be disarmed and the ignition in the car must be turned off. Also disabled mode Free hands and preferably the door is open so that there is no re-arming during programming.

   1) Timed autostart setting (every 2, 4 or 8 hours)
   b) To activate the timed autostart mode, press the IV button 13 times in succession (the siren emits a beep after each button press; that is, press once, we hear a beep, press a second time - we hear a beep and so on 13 times)
   c) Wait for the siren to beep 13 times in a row.
   d) Then select the desired autorun time button II - 8 hours, III - 4 hours or IV - 2 hours.
   

   2) Setting autostart by temperature (when t is reached in the cabin -15, -25, +60)
   For the autostart to work correctly when the temperature is reached, 3 steps must be performed:
   
   2. Turn on temperature control (mode 1-21 in II, III or IV)
   a) Recall that the entry into the function programming mode is carried out by long pressing the I + II buttons.
   b) To activate the autostart mode by temperature, press the IV button 21 times in succession (the siren beeps after each button press; that is, we press once, we hear a beep, we press a second time - we hear a beep and so on 21 times)
   c) Wait for the siren to beep 21 times in a row.
   d) Then choose required temperature autorun button II - (-15), III - (by -25) or IV - (+60).
   e) After that, you need to turn on the timer from the key fob. Press simultaneously II + IV briefly, the display will show the inscription “timer”. If it was activated (lit) before programming, it must be switched off (also II+IV) and switched on again.

   3) Autostart setting by on-board voltage
   Implementation of the delay of the timer start up to the moment of discharging battery up to 11.5 V, is carried out as follows:
   1. Enable time trigger (mode 1-13 in II, III or IV) see 1) a), b), c)
   a) Entering the function programming mode by long pressing the I+II buttons.
   b) To activate the voltage autostart mode, press the IV button 20 times in succession (the siren beeps after each button press; that is, we press once, we hear a beep, we press a second time - we hear a beep and so on 20 times)
   c) Wait for the siren to beep 20 times in a row.
   d) This will enter the programming mode of the function Limit timer starts by battery voltage.
   e) After that it is necessary to press button II to activate the mode.

   Engine warm-up time:

   To set the engine warm-up time, set function 1-12 to position II.
   In more detail, you need to do the following:
   a) Entering the function programming mode is carried out by long pressing the I + II buttons.
   b) To set the engine warm-up time, press the IV button 12 times in succession (the siren beeps after each button press)
   c) Wait for the siren to beep 12 times in a row.
   d) Then select the desired duration of the start button I - 5 minutes, button II - 15 minutes, III - 25 minutes or IV - 45 minutes.

   Make sure the system is disarmed and lit before programming.

3. You set the desired temperature by programming the center. block and on the keychain you put the start on a timer, it seems like this.

Example notation:

I - quick (0.5 sec.) button press

I - long (2 sec.) button press

(I + II) - fast (0.5 sec.) simultaneous pressing of the buttons (combination of buttons)

(I + II) - long (2 sec.) simultaneous pressing of the buttons (combination of buttons)

Note:

With a long 2 sec. pressing the I button, the car alarm operation modes are sequentially changed in the order (1) > (2) > (3) > (1) .... In mode (2) the "Hands-free" function has a long working range - the symbol flashes.

Setting the time on the keyfob-communicator display

Setting the current time is required before starting the operation of the system or when changing the key fob battery. Follow the steps according to the table below.

ATTENTION!

Setting the correct time is necessary condition for correct operation automatic start of the engine by timer.

Setting the key fob-communicator modes.

Vibration call, owner call, temperature display standard "°F" or "°C"

To set the desired operation mode of the car alarm key fob, follow the steps in accordance with the table below.

Backup mode (only for manual transmission)

The standby mode excludes the possibility of automatic starting of the engine if the manual transmission lever is not set to the neutral position. Depending on your requirements, you can choose one of three redundancy algorithms (programmable function 1-6).
Algorithm 1

Algorithm 2

To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:
At the end of the trip, without turning off the engine, place the gear lever in neutral position
Remove the key from the ignition switch (in the OFF position). The engine will keep running
Open the door and get out of the car. Close the door. The engine will stall.

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, redundancy will be prohibited if the door, hood / trunk are open at the time the ignition is turned off.
Algorithm 3

To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:
At the end of the trip, without turning off the engine, place the gear lever in neutral position
Close the hood/trunk doors
Press for 2 sec. key fob button II
Remove the key from the ignition switch (in the OFF position). The engine will keep running
Open the door and get out of the car. Close the door. Engine will stall

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, the implementation of the reservation requires you to each time press button II of the key fob before turning off the ignition (by turning the key in the ignition switch to the OFF position).

To autostart Sherkhan 5 from the key fob, press and hold button II for at least 2 seconds, as shown in the figure.

ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!

In this case, the car will forcibly switch to armed mode with the engine running. The doors will automatically enter the close mode, after which the system will be set to the engine start mode. If the process of starting the engine is successful, then the key fob will display information about the time remaining before the engine stops working in minutes-seconds, and smoke from the exhaust pipe. This time can be programmed in the modes of 15, 5, 25 minutes or 45. To make a trip without stopping the engine within the programmed auto start duration, it is necessary to open the driver's door, then insert the key into the ignition lock, turn it to the "Ignition On" position. The period of time between opening the door and turning on the ignition mode is limited to 20 seconds. This event is provided in order to increase the security of the car against theft during the warm-up period. If within 20 sec. the ignition will not turn on, the engine will stop.

If the engine start was unsuccessful, security system will try to start again. After the 3rd unsuccessful attempt, the car alarm will go into standby mode. To resume the autorun function, it is necessary to diagnose the engine and the main systems of the car. Possible reasons the fact that the engine autostart does not work:

• weak battery charge;
• extremely low temperature engine in the cold season;
• immobilizer problems limiting remote start engine;
• malfunction of the electrical equipment of the car;
• there is no control over starting the engine (the engine did not start, but there is smoke on the indicator, so a second attempt to start is not made);
• failure of other engine systems internal combustion associated with difficulty starting.

If the engine is started with the key, but the remote start does not work, it is necessary to reprogram the autostart system, reducing the starting frequency, increasing temperature regime triggering. Perhaps the problem will be fixed.

When starting the engine, the security system will signal the following signals.

The car is not set to autorun, if during its production:

• the ignition is in the "On" position;
• one of the doors is open;
• the engine is already running;
• the "reserve" mode is not activated in cars with manual transmission.

In the event of a successful engine start, the devices will signal:

In the case when the engine stops automatically, the devices generate signals:

Programming autorun time intervals

The car alarm provides programming of time intervals (autostart time) after two, 4 and 8 hours. The choice of a specific option is made depending on the operating conditions of the car, the condition of the engine and the battery. To start the programming operation, it is necessary to simultaneously long press the buttons I and II. Next, you need to perform the following operations in the following sequence:

1. Turn off the “timer” option (if it is activated) by briefly pressing buttons II and IV at the same time. The "timer" should be deactivated on the display.
2. Press the IV button thirteen times. Each entry is confirmed by one siren signal.
3. Wait for the siren to give a 13-fold sound confirmation of the entered information.
4. Use the key fob buttons to confirm the selected autorun mode. Button II corresponds to the autostart mode after 8 hours, III - after 4 hours, IV - after two hours.
5. Set to autostart by turning on the "timer" mode by briefly pressing buttons II and IV at a time.

Reprogramming the autostart mode according to the interior temperature

For correct activation of autostart according to the characteristics of the passenger compartment temperature, it is necessary to activate the start modes by time (1-13) before enabling the programming option. Next, you need to switch to the programming mode by long pressing the corresponding buttons on the key fob I + II. Then the following operations are performed:

1. Turn off the "timer" mode (if it is activated), as described in the previous paragraph.
2. 21 times methodically press the IV-th button, after which the siren will signal.
3. Wait for the siren alarm 21 times in a row.
4. Set the desired autostart temperature mode: button IV - plus 60 degrees Celsius, III - minus 25, II - minus 15.
5. Activate the timer mode.

Warm-up programming

The warm-up time can be set to fixed intervals of 5, 15, 25 minutes or 45 minutes. To do this, activate function 1-12 in mode II. Programming is entered by long pressing I + II, after which the following operations are performed:

1. Button IV is pressed twelve times (accompanied by a sound signal).
2. 12-fold siren signal - confirmation.
3. The engine operation time is selected by activating buttons I (5 minutes), II - 15, III - 25 or IV - 45 minutes.

Programming autostart by the voltage of the on-board network

Autostart can be programmed when the battery is discharged to an amplitude of 11.5 volts. First you need to activate the start by time (1-13), then enter the programming by long pressing I + II. Here are the buttons to press:

1. 20 consecutive IV button presses.
2. Waiting for the siren to sound 20 times.
3. Activate the battery voltage response mode with button II.

Autorun problems

Some vehicles have the following autostart problems:

1. When the ignition is turned off, the car does not stall. To disable autorun, you need to open and close the doors. To correct the problem, function 1-16 (Button II option) is required. In this case, in order to turn off the engine, it is necessary to switch the key to the "Ignition Off" position.
2. Activation of the "Valet" mode after emergency disarming (zzz symbols on the key fob). To fix the problem, simultaneously long (more than 2 seconds) press the I + III buttons.
3. If it is necessary to urgently turn off the car from the key fob during the autostart period, it is necessary to long press the II button.

To set autorun with Scher-Khan keychain magicar 5, press button 2 on the key fob and hold it down for more than two seconds. With this manipulation, the car will be set to armed mode with the engine running, the doors will be locked, and after that the engine will be started. If the engine is started successfully, then the key fob will display information about how much time is left for the engine to run before stopping (it is most convenient if the time interval is programmed in minutes - from 5 to 45 minutes). If the launch has taken place, then in the distance you can see light smoke from the exhaust pipe.

To start a trip, during the set autostart interval, when it has not yet expired, open the driver's door, insert the ignition key into the lock and switch it to the position that corresponds to the inscription on the ignition on. All these actions must be done in no more than 20 seconds, if you delay in time, the ignition will not turn on and the engine will be turned off. As you understand, this is provided to prevent malicious attempts to steal your car.

If the launch fails, the Sherkhan Magikar 5 system will make a second and then a third attempt to start the engine. If all three attempts to start did not take place, then the security system will stabilize in standby mode. To re-initiate the autostart function, you must first make sure that the engine is working.

Why autorun Scher-Khan magicar 5 does not work

Possible reasons for autorun failure are as follows:

• discharged battery;
• the temperature outside the window in winter has reached a critically low level (preventing the easy operation of this function);
• other ICE systems could malfunction, making it difficult to start the engine;
• car electrical failure
• problems are related to the immobilizer, which prevents autorun;
• the indicator shows smoke, although the engine did not start, so the system does not attempt to start 2.

If, when the key is flogged, the ignition works, and the auto start from a distance does not work, then you need to reprogram it, you can try to do the following - make the start periods shorter and set the response temperature higher.

How the Sherkhan Magikar 5 alarm works during launch:

When it is not possible to set to autorun:

• with the ignition off;
• if not all car doors are closed;
• if the motor is already running;
• in cars with mechanical transmission - if the "redundancy" mode is not active.

If the remote start is successful, then the corresponding systems behave as follows:

When the engine is automatically stopped, the systems behave as follows:

How to set the warm-up interval for autorun Sherkhan Magikar 5

To get started Scher-Khan installation magicar 5 in time, simultaneously with two fingers, press the first and second buttons on the key fob and hold the buttons like that for some time. (The autostart interval is possible 2, 4 or 6 hours - which specific value to choose depends on the condition of the battery and engine.)

1. Briefly press the Roman buttons 2 and 4 once without holding them down - this will turn off the timer.

2. Press the Roman button 4 13 times (after each pressing, the siren will confirm), then wait until the siren confirms the received signals 13 times.

3. It remains to select the autorun interval: to set autorun after two hours, press the Roman button 4, so that after 4 hours, press the Roman 3, after 8 hours, press the Roman 2.

4. Finally, finish the auto-start setting by turning on the timer by pressing Roman buttons 2 and 4 once and immediately releasing them.

How to set autorun Sherkhan Magikar 5 by temperature in the cabin

1. First, in a way already known to us, you need to turn on the autorun mode by time - to do this, press button 4 13 times (after each press, the siren will confirm), and then wait until the siren confirms the received signals 13 times.

2. Switch to programming mode. To do this, simultaneously press two fingers on the first and second buttons on the key fob and hold the buttons like that for some time.

1. Deactivate the timer (if it is not already off) by briefly pressing buttons 2 and 4 simultaneously.
2. Press 21 times on the Roman button 4 - the siren should turn on.
3. Wait until the siren sounds 21 times, and then proceed to the temperature selection.
4. To turn on autostart at minus 25°С, press button 3, at minus 15°С, press button 2.
5. Restart the timer? by pressing buttons 2 and 4.

How to program the warm-up duration

The warm-up time on the Sherkhan Magikar 5 alarm can be selected in the form of specific time periods in minutes (5, 15, 25 or 45 minutes).

1. First you need to turn on the programming function by simultaneously long pressing buttons 1 and 2.
2. Press button 4 12 times, each press will be accompanied by a sound confirmation, and the final confirmation of programming is 12 siren sounds in a row.
3. It remains to set the warm-up time. To warm up for 45 minutes, press button 4 to 25 minutes. – button 3, 15 min. – button 2 and 5 min. – button 1.

How to program autostart by on-board voltage

You can program auto start, in case the battery is discharged to 11.5 volts.

• Enter the time trigger mode by pressing button 4 13 times.
• Activate the programming function by simultaneously long pressing buttons 1 and 2.
• Press button 4 20 times without stopping, after which the siren will also sound 20 times.
• Press button 2 - in this way you will turn on the autorun operation mode by battery voltage.

The most common problems with autorun

1. The “Valet” mode is activated when the car is urgently disarmed (zzzz signs appear on the key fob). To solve the problem, you need to, with two fingers at the same time, press buttons 1 and 3 for more than 2 seconds.
2. When the ignition is off, the car does not stall. The doors are locked, and in order to deactivate autorun, you need to activate the car's doors. To get out of this situation, you need to use button 2 to perform functions from 1 to 16. To turn off the engine, you need to turn the ignition key to the "Ignition Off" position.
3. If you urgently need to remotely turn off the engine when autostart is running, then press button 2 and hold it.

Video: Setting up an auto-start alarm Scher Khan magicar 5 on manual transmission

Video: Car won't start with Scher alarm Khan magicar 5. Search for the cause

If the video is not showing, refresh the page or