Scher-Khan Magicar V - user manual. Scher-Khan Scher khan magicar 5 remote control programming instruction manual

The Magicar 5 alarm system is an effective anti-theft system that helps protect your car from intruders.

Management is implemented by means of a key fob that transmits commands over the air. To improve ease of use, the key fob has a liquid crystal display.

ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!

It displays information both about the current state of the system and helps in setting up the Sherkhan 5 alarm. The working distance of the radio channel is 1500 meters.

To automatically activate or deactivate the car security mode, depending on the location of the car owner, use the " Free hands». Sherhan Magicar 5 allows you to use two options:

To set up the function, it is necessary to hold down the “I” button for 2 seconds. In this case, the mode change will occur in the following sequence:

• Activation of the minimum sensing distance.
• Activation of the second mode.
• Mode deactivation.

All settings are accompanied by a melodic signal. If unnecessary, it is recommended to turn off free hands, as prolonged use of the function leads to a reduction in the battery life of the key fob. This is due to the periodic check of the presence of the car owner.

sherhan alarm time setting

In addition to automatically starting the engine by a control signal from the key fob, magicar 5 has the ability to start the engine using an internal timer. The icon will then appear on the display. For correct operation function, the clock needs to be set when using for the first time or after replacing the battery in the key fob. It is performed in the following sequence:

• Hold down the combination of buttons "II" and "III" for 2 seconds. Key fob programming will be activated, accompanied by a sound signal.
• Press "I" for half a second. The time will start flashing.
• Use the "I" and "II" keys to set the hours and minutes, respectively.
• To fix the set values, you need to leave the programming mode by simultaneously holding "II" and "III" for two seconds. This process will be accompanied by an audible signal.

Incorrect time setting will lead to desynchronization of the key fob readings with the real clock. Because of this, it is not possible to properly adjust the automatic start timer. The start of warming up the engine and interior will occur earlier or later than the car owner's expectations.

Disable turbo mode

The operation of a car with a turbocharged engine has its own subtleties. To prevent damage to the blower mechanism, do not turn off the engine immediately after a trip. To eliminate the need to wait until the turbine cools down, a turbo timer is used. This function is integrated into the Sherkhan alarm system. Thanks to this, the engine runs for two minutes at idle at the end of the trip.

In order to enable or disable the turbo mode, you need to press the key combination "III" and "IV" for a short time. In this case, depending on the state of the function, the signals and indications indicated in the tables below will be observed.

Table of signals and indications when turbo mode is activated

Table of indications and signals accompanying turbo timer deactivation

Magicar 5 immobilizer crawler

The incompatibility of the autorun system with the immobilizer leads to the need to install a crawler. This module is not included in the basic package of the Sherkhan alarm, so it will need to be purchased separately.

The device practically does not require the participation of the car owner in setting up. After installation, the immobilizer crawler automatically reads the engine unlock code. The received information is stored in the module's memory. After that, starting the engine becomes possible without the participation of the immobilizer unlock key.

"Jack" mode of the magicar 5 alarm

The VALET function is usually used when transferring a car to a station Maintenance. The mode can be activated by pressing the combination of the "I" and "III" buttons for two seconds. After that, the possibility of unlocking and locking the car locks by pressing "I" or "II" remains available. A successful transition to the VALET mode is signaled by an icon.

Activation VALET mode

Upon completion of the maintenance of the car, the jack mode should be removed. To disable the mode, hold down the "I" and "III" keys. It is forbidden to give the key fob from the alarm to the service station personnel, as this can lead to the subsequent theft of the car.

Deactivation of the "Jack" mode

Setting the shock sensor

To carry out adjustment work, it is necessary to find the place where the shock sensor is attached. Usually the device is easily accessible for configuration. In case of difficulty with the search, you should contact the service center.

The shock sensor changes its sensitivity depending on the position of the regulator located on it. Turning clockwise increases the device's response to stimuli. Turning the knob to opposite side, the sensitivity decreases. In the extreme position, the sensor is switched off.

Difficulties in setting up an alarm

Alarm malfunctions can lead to the inability to configure it. For example, a discharged battery will not allow the processor module to receive control commands from the key fob. In this case, the low battery icon will be displayed on the display.

Dirty keys can also make it difficult to set up the system. Attempting to push the buttons harder leads to damage to the key fob. For troubleshooting, it is recommended to contact the service center.

The Sherkhan Magikar 5 alarm system has excellent performance characteristics and high reliability. The instruction manual gives a detailed explanation about the principles of using this device and its main functions.

purpose

The instruction "Sherkhan Magikar 5" indicates that this alarm can be controlled by the user remotely, which is helped by an exclusive keychain communicator. The display is made of liquid crystal material, so it is considered particularly reliable.

A specially built-in system regulates a single interaction mechanism processor unit with keychain communicator. You can control the alarm from a distance of 1500 m.

The engine starts after a special command is given. It is usually sent along the key fob, the outer part of the device, the internal timer. This does not take into account the temperature in the car, and the voltage level of the battery is also unimportant.

Advantages

Preparing the key fob for work

Before using the key fob, you need to perform several manipulations, since there is no battery in it during transportation. It is located separately, and not in the proper compartment. This is necessary to conserve battery power. in full. When you remove the battery, no power is consumed, so there is no need to additionally recharge the device.

To place the battery in the right place, carefully remove the latch that holds the Sherkhan Magikar 5 battery cover in its original position. In this case, malfunctions are excluded, since all structural elements are made with maximum quality. This applies to both cutting parts and the material from which they are created.

After performing this action, it is necessary to move the cover itself to the side that runs opposite to the protruding antenna. The battery for power should be carefully installed in the compartment. As with any battery, polarity is provided here, so the position of its sides can only be determined after familiarizing yourself with the graphic pattern near this compartment.

If any indicators are missing, then the Sherkhan Magikar 5 signaling is placed with a minus sign in the direction where the antenna is located. After correct installation a characteristic melody is heard, which indicates the completion necessary action for the correct operation of the system. You only need to close the battery storage compartment cover, and then install the appropriate lock on it.

Arming

To activate the security mode, you must first turn off the ignition, and close all compartments of the car to ensure the free operation of "Sherkhan Magikar 5". The operating manual determines that the button number 1 on the key fob is then pressed with only one touch. It is not necessary to hold it for a long time, a point and moderate touch is enough. The system will automatically translate everything necessary elements machine in guard mode. The existing locks on the doors will be blocked, the starter will not work until the owner himself removes this mode.

When the car alarm "Sherkhan Magikar 5" is armed successfully, a person can trace some signals:

1. The siren will sound once with a moderate whistle.
2. The emergency light signal will also make itself felt once.
3. An LED indicator will turn on, which will show that the car is under protection by means of measured flashing at a frequency of 1 time per second.
4. The headlights flash five times simultaneously. Further, the image of the closed lock will remain lit until the car is unlocked, and the headlights will go out.
5. The key fob will give only one short signal.

Enable sensors

When the LED begins to flash steadily, this means the activation of the system control over the state of all possible inputs and methods of penetration into the car, which the Sherkhan Magikar 5 cannot allow. The instruction manual reports that even the sensors for calling the owner and ignition control are additionally checked and constantly monitored, which allows the owner to calmly do any of his business at this time.

If connected additional function, which is responsible for regulating the delay of the cabin light, will also provide for the control of triggers, which usually do not begin to be guarded immediately, but only after a certain amount of time has passed. activates work 30 seconds after the machine has been armed.

A warning

The instruction "Sherkhan Magikar 5" warns users against inattention to the car. Do not leave doors, hood and luggage compartment open. If this happens, then the person suddenly, instead of the usual behavior of the car when arming, hears a three-time key fob signal along with a siren. In this case alarm also flashes three times at once.

On the display, you can see the image of the item that the owner of the car forgot to close. This happens only for five seconds, so the user may not have time to see the desired item. At the same time, the text FALL appears on the display. This is a direct indication that you should find an unclosed element and cover it tightly.

"Sherkhan Magikar 5" instruction manual defines as a device upper class, since it sets all vehicle communications on guard, but it bypasses the activated sensor. It will automatically be additionally protected after the owner closes it. The hood area is not reflected in common panel, as it refers to the trunk area.

Automatic transition to armed mode

Passive arming is a separate feature that can be enabled or disabled for Sherkhan Magikar 5. The autorun instruction provides - you just need to change the state of the selected function. If the owner decides to activate just such a mode, then immediately after the last door is closed, the timer is activated, and the security is turned on after 30 seconds.

When the countdown is started, the system constantly sends warnings that this mode will turn on. This happens every 10 seconds. If any door is opened at the specified time, the system will activate the armed mode at the countdown of 30 seconds after the last door is closed. You can see if this function is working by the word PASSIVE, which is always shown on the display in this case.

Alarm mode

When Sherkhan Magikar 5 is operating, malfunctions are unacceptable. When any door is opened, the system will automatically be in alarm mode for exactly 30 seconds. When this time is over, it will return to the standard state again.

If the cause that caused the alarm has not been eliminated by this time, the signal will sound every 30 seconds and last for half a minute. This cycle is repeated eight times. If even then the reason for the violation of the usual mode is not canceled, the system returns to the armed mode, but on condition that the active sensor is bypassed.

Features of work

If the shock sensor is triggered, that is, there is a strong impact on any part of the car, the Sherkhan Magikar 5 alarm will be in alarm mode for 5 seconds, during which a strong signal from the siren and alarm is given.

With a weak impact, that is, the activation of the warning zone, also regulated by the shock sensor, 4 short ones will sound, which are generated by the Sherkhan Magikar 5 car alarm. There were no malfunctions in this process, so the owner of the device can be sure of his own technique.

Many users appreciate the ease of use of Sherkhan Magikar 5. How to disable security mode? With a short one-time press on the key fob button number 2. If you correctly program all the functions of the device, the alarm will become a reliable assistant in ensuring the safety of the car.

Wanting to understand how to enable autorun on Sherkhan 5, you should study the instruction manual, know the principle of operation and the modes implemented in this system car alarm. It is controlled by using a switching key fob with an LCD display, via a radio channel. Broadcasting of signals is carried out at a distance of up to 1.5 km.

The device is equipped with cars equipped with a gasoline or diesel power unit, with a voltage in the on-board network of 12 W. The alarm system has the option of automatically starting the engine by activating a command from the key fob or starting from a timer.

Preparation for work

How to enable autorun on Sherkhan 5 is presented below, but first the alarm must be prepared for work. Before you start using the key fob, you will need to perform certain actions aimed at its correct activation. The fact is that in order to maintain a full charge of the battery, manufacturers supply the power supply separately from the main device.

To install the battery in the provided compartment, you should carefully remove the latch that holds it in closed position cover of the respective compartment. Usually, this operation does not cause any problems, since the body and other elements of Sherkhan 5 are made of high-quality and high-strength materials.

The next step involves moving the key fob cover opposite to the antenna and placing the battery in the compartment with the polarity observed. After adequate installation of the specified part, a characteristic melodic sound should be heard, after which it is necessary to reinstall the cover and retainer.

Auto start setting

Enabling autorun is described in detail in the presented step-by-step instructions:
Button press modes differ in two ways (important):

• Short-term activation - a single impact on the key, lasting no more than a second, which is accompanied by a short signal;
• Long press - fixing the button for more than 2 seconds until a sound notification appears, after which you can release the key.

Further tuning of the engine excitation programming is shown using functions 1-12 for 25 minutes as an example. First you need to enter the settings mode No. 1, activate buttons 1 and 2 at the same time. Hold them until the remote control beeps. If the manipulation is carried out correctly, the alarm will be in the programming sector.

Next, you need to carry out successive touches of button No. 4 in the amount specified by the program. Each click must be confirmed a specified number of times. In this example, 12 clicks. At the end of activation, you should hold the button for 3-4 seconds, after which, the device will sound 12 notifications to confirm the programming item.

Features on a specific example

The autorun settings of Sherkhan 5 every 2 hours or when the temperature in the cabin drops to -15 ° C, with the cabin warming up for 25 minutes, perform the following manipulations:

• At the same time, buttons I and II are activated, then, pressing VI twelve times, and finally, holding the button III (functions 1-12 are configured taking into account the temporary value of 25 minutes);
• Activators I and II are pressed simultaneously, button No. VI is clicked 13 times (alarm functions No. 1-13 are set to a time indicator of 2 hours;
• Perform pressing simultaneously I + II and VI - 21 touches (function 1-21 is set to a temperature of - 15 ° C).

Scher-Khan Magicar V - one of the past generations of the popular alarm system, combining security, control and boost performance characteristics car features. Scher-Khan Magicar V is one of those types of car alarms that have feedback carried out using the remote control.

The Scher-Khan Magicar V alarm is controlled remotely using a key fob with a display located on it. The key fob allows you to remotely control the alarm functions using several keys on the key fob (I, II, III, IV), various combinations of buttons and the length of pressing - short presses (0.5 sec) and long ones (2 sec).

Setting the time on the key fob

Setting the exact time on the key fob display is necessary procedure in order to be able to start the car engine on a timer in automatic mode. Since when the power is turned off exact time is reset, then the installation is carried out not only before the start of operation, but also when replacing the battery.

Setting the exact time on the key fob consists of several steps.

1. It is required to press a combination of buttons II and III. The duration of pressing is 2 seconds. After that, the programming mode is entered, about which the owner is notified by a sound signal from the key fob, a flashing alarm and a special symbol on the display.
2. Next, press the I button and hold it for 0.5 seconds. Thus, the mode of setting the exact time is activated, confirmed by a sound signal. The display of the device shows the current time flashing.
3. Next, the exact time is set. With button I you can change the hour, with button II you can change the minutes. To change by one step, you must hold the desired key for 0.5 seconds.
4. The last stage is the exit from the programming mode, which is carried out by pressing the combination of keys II and III. Exit from the mode is confirmed by a sound signal.

Reset to factory settings

Errors in self-programming of alarm functions may require a rollback to the factory settings. Resetting the programmable alarm functions to factory values ​​is carried out in 2 stages.

1. At the first stage, you should enter the programming mode - press buttons II and III simultaneously and hold them for 2 seconds.
2. At the second step, you need to press button III on the key fob three times (0.5 seconds each). Each press is accompanied by a flashing "emergency gang" and a sound signal. After a short period of time, 3 beeps should sound and the alarm will flash three times. Thus, the owner is notified about the reset of the function programming settings to the “default” settings.

Engine starting

The Scher-Khan Magicar V alarm allows you to start the car engine using the remote control. To do this, press button II of the keyfob and hold it for 2 seconds (long press). In this mode, the alarm goes into armed mode, the car doors are locked, and the engine starts. The duration of the motor can be programmed for different time periods:

• 5 minutes;
• 15 minutes;
• 25 minutes;
• 45 minutes.

The engine start is accompanied by several indicators confirming the successful execution of the request:

• siren signal
• key fob sound signal;;
• flashing "emergency gang";
• 5-fold headlights on the key fob display

If the engine start fails, the system will retry a maximum of 2 more times. If after them the engine start is not possible, then the alarm goes into normal mode.

In order to start moving the car, the driver, with the engine running from the key fob, needs to open the doors, insert the ignition key and turn it to the ON position. To do this, the driver has 20 seconds after opening the doors. If during this period the key is not turned to the desired position, the system will automatically turn off the engine.

The alarm may not start the engine for several reasons:

• the motor is already running;
• the ignition is already on;
• the doors or trunk are open;
• the reservation mode for vehicles with manual transmission has not been performed (the control lever has not been moved to the neutral position).

Therefore, in order to automatically start the engine, the driver of a car with a manual transmission must first, after stopping:

• set the gearbox lever to the "Neutral" position without turning off the engine;
• close the hood and trunk;
• press button II on the key fob;
• turn the ignition key to the off position and pull it out (the engine will continue to work);
• get out and slam the door (the engine will stall).

Autostart Programming

The Scher-Khan Magicar V alarm system allows automatic engine start in various modes:

• every 2 hours;
• every 24 hours.

Starting the engine every 24 hours allows you to start the engine at the same time every day, which is convenient, for example, for warming up in the morning. Starting every 2 hours allows you to maintain the temperature of the engine and interior on cold days or, conversely, to cool the interior in the summer season. Both timer modes cannot be used at the same time. The choice of the autostart mode is made through the menu of programmable functions.

To program the autostart every 2 hours, briefly press the buttons II and IV. In this case, the engine will automatically start 2 hours after pressing. Setting the time is not required in this case.

To automatically start the engine every 24 hours, you must first set the exact time on the key fob, if it is not set. (how to do this - see above). The automatic start of the motor is set as follows:

• you need to press buttons II and IV and turn off the Timer mark;
• select start time using keys I and II;
• press the II and IV keys again and turn off the Timer label.

When the engine is automatically started, the key fob display shows a countdown until the moment when the engine is turned off.

Auto start by temperature

Automatic start can be set when reaching certain temperature air, which is determined temperature sensors installed in the vehicle interior. Temperature autostart can only be used in combination with timer autostart. To set autostart only when a certain temperature is reached, you must:

• select auto start by timer;
• turn on temperature control - press the IV button 21 times;
• choose the required temperature regime(key II - -15 °C, key III - -25 °C, button IV - +60 °C);
• turn on the autorun mode by timer (see above).

How to register a keychain?

The Scher-Khan Magicar V alarm can "remember" 3 different key fobs. To sync new keychain with an alarm you need:

• turn the ignition key three times from the OFF position to the ON position - the “emergency flasher” should flash 1 time, confirming the entry into the programming mode;
• no later than 4 seconds after the flash, you need to press the I key on the new key fob;
• then you need to enter the key fob code into the memory of the signaling processor unit.

The memory of the processor unit can store data of only 3 key fobs, so when the fourth key fob is registered, the code of the first one is deleted from the memory.

You can exit the programming mode without taking any action within 4 seconds after writing the last digit of the code.

How to turn off the alarm?

To disable the security functions of the alarm system, a special VALET mode is provided. The deactivation function is necessary, for example, when transferring the car to the station after-sales service to prevent an alarm. To switch to the VALET mode, a short press of the I and III keys is enough. You can also turn on the mode with the ignition key - just like when registering a new key fob, you need to turn the key in the cell from the OFF position to the ON position three times, that is, enter the programming mode. Further, no action should be taken for 4 seconds, after which the system will automatically switch to VALET mode.

In VALET mode, the door opening/closing function is stored, for which you need to briefly press the I button. You can exit the VALET mode by pressing the combination of keys I and III.

Shock sensor adjustment

The shock sensor notifies the owner of the car about an incident with the car while the car is parked with the alarm on.

Sensors Scher-Khan alarms Magicar V two-level: low impact beeps 4 times and alarm flashes 4 times. At strong blow the key fob goes into alarm mode, lasting 30 seconds - 30 flashes of the "emergency gang" and 30 short beeps. Shock sensors can be turned on or off by pressing the combination of buttons I and III and holding them for 2 seconds.

Adjusting the shock sensor helps to avoid false alarms from the accident warning sensor, since with a sensitive sensor, even the passage of a neighboring car can be falsely perceived by the system as an emergency impact. To adjust the sensitivity of the sensors, physical access to them is required; you can find out about the location of the shock sensors at a service station. Regulators are installed on the sensors themselves, turning clockwise increases sensitivity, counterclockwise - reduces until the sensor is completely turned off.

Programming the CTCTS functions using a key fob consists of four steps.

1. Enter programming mode and select the programming menu. To enter Menu No. 1, press the I + II buttons simultaneously for 2 seconds. To enter Menu No. 2, press the I + IV buttons simultaneously for 2 seconds. The siren will sound one short beep and the vehicle alarm will flash once, confirming the successful completion of STEP 1.

2. Press the IV button to select the Menu function you want to change. The number of presses must correspond to the number of the selected function. For example, to select function 4, you need to briefly press the keyfob button IV four times. Each button press will be confirmed by a short siren tone (if enabled) and a flash of the car alarm.

3. Wait a few seconds. The system will confirm the number of the selected function to be changed with short siren beeps and car alarm flashes. The number of signals will correspond to the number of the selected function.

Note:

If, when choosing a function, you made a mistake with the number of clicks and (or) there are no siren and alarm signals, then you must repeat all the actions starting from STEP 1.

4. Press the I button to select the factory setting for the function. To confirm this, the siren will give one short signal, the alarm will flash once. Press the II, III, or IV button to select optional function values. To confirm this, the siren will give two, three or four short beeps, the car alarm will flash two, three or four times.

Note:

If you hear one long signal from the car alarm siren, this means that the system has exited the function programming mode. To continue programming, repeat all steps from STEP 1.

ATTENTION!

If you want to change more than one function from the Menu you have selected, then the selection of each function to change must begin with STEP I.

Menu of programmable functions

Menu #1 [Button (I + II)-]

Note on function 1-4: This function allows you to select "Panic" or Jack Stop mode™ (robbery protection):

Resetting all programmable functions of Menu No. 1 to factory defaults

1. Enter programming mode. Press buttons I + II simultaneously for 2 sec. The car alarm siren will sound one short beep and the alarm will flash once, confirming the success of STEP 1

2. Briefly press button III on the car alarm key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time, three siren sounds will sound, the alarm will flash three times, confirming the factory settings of all menu 1 programmable functions.

Menu #2 [Button (I+IV)-]

Resetting all programmable functions of Menu No. 2 to factory defaults

To reset the programmable features to factory defaults, two steps are required.

1. Enter programming mode. Press buttons I + IV simultaneously for 2 sec. The car alarm siren will beep once, the alarm will flash once, confirming the success of STEP 1

2. Briefly press button III on the key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time after this, three siren sounds will sound, the car alarm will flash three times, confirming the factory settings of all programmable car alarm functions of menu No. 2

KEYFOB-COMMUNICATOR CAR ALARM SCHER - KHAN 5

Preparing the key fob-communicator for work

Before using the key fob, you must bring it into working condition, because. during transportation and storage, an insulating gasket is installed between the contact of the battery and the contact plate of the key fob, which prevents the battery from discharging before operation. Before using the key fob, remove it. To do this, release the battery compartment cover lock, press the cover and slide it in the direction opposite to the antenna. Remove the battery. Remove the insulating pad between the battery and the collector plate. Install the battery back, observing the polarity indicated on the bottom of the battery compartment. If there is no indication of the polarity of the battery, then it is set with a negative terminal towards the antenna. Close the battery cover. After that, the keychain is ready to work.

Symbols on the display of the key fob-communicator of the car security system

	Timer start indicator
	TURBO mode indicator
	Passive arming indicator
	"Hands free" mode activation indicator
	Siren indicator
	Shock sensor off indicator
	Vibrating alert indicator
	Power indicator automatic control CZ for ignition
	Door open indicator
	Trunk/hood open indicator
	Shock sensor alarm indicator (optional sensor)
	Car owner call indicator