How to register a new Tomahawk keychain. Programming the alarm key fob and how many remotes can be assigned to one unit How to set up the remote from the car alarm

Often a situation occurs when, by pressing the key fob, the security system does not work. There is no need to panic about this. This can happen with any device.

If the remote control is damaged, then you need to purchase a new one or get a spare one. The key fob is intact - then you can easily tie it to the Sheriff alarm yourself. Failure in work most often occurs through the fault of the owner, due to frequent button presses for the sake of entertainment.

Zx 750 755 757 dialog 434
930 935 940
phi 500 aps 2400 aps 2500
2600 2625 aps 25
aps 35

Keychain registration methods Sheriff

Before you start binding the Sheriff 900 or APS 2400 TX anti-theft system remote control, look for the “Jack” button located somewhere inside the car. It is small in size and can be located in various hard-to-reach places:

• under the steering wheel;
• in the glove compartment;
• behind the plastic panel.

1. Sit in the car, close all doors, turn the ignition key to the first position.
2. Press "Jack" three times. The Siren will emit a CHIRP.
3. Click and hold the Arm button on the remote. The car will beep again.
4. Hold "Lock Car" on the next key fob until the siren sounds. Repeat this for the remaining pagers, if any.
5. After six seconds of inactivity, the alarm will beep, indicating the completion of registration. Key rings can be used.

Remote control reprogramming

Adaptation of the remote alarm unit 725 and zx 750 is not always performed due to its failure. When buying a used car, the former owner gives you two key fobs. There is no complete certainty that he did not leave himself alone. After all, the basic kit includes four communicators. In this case, be sure to reflash the key fobs.

1. Turn the ignition key to the first position.
2. Press Valet three times quickly. The siren beeped.
3. Click on the "Close" keychain. CHIRPS will sound again.
4. Click on the second pager "Auto arming". The siren will beep again.
5. Switch off the ignition. Previously used remote controls will be erased from the memory of the anti-theft system.

It is easy to flash the Sheriff communicator yourself, just follow the instructions clearly and you will succeed.

How to set up an alarm on a new key fob

The Sheriff's remote control broke, and you bought another one. How to do programming? There are many videos on the web on this subject. And if there is no Internet and a computer. Linking a new remote control is carried out according to the following procedure (suitable for 925, 1070, 1050, etc.).

1. Activate the ignition.
2. Find the Valet button and press it three times in five seconds.
3. An audible signal sounds.
4. Press "Close" on the remote. Ready.
5. If there is a need to record additional key fobs, then this should be done within five seconds. Otherwise, the system will automatically exit programming.

After these steps, the new remote control is ready for use.

Why is it not programmed

It is not always possible to program the Sheriff 940, 2500, 4BTX940LCD, APS95LCD B4 remote control key fob, etc. This is due to incorrect system operation:

• remote control is defective;
• the alarm is constantly in the "Jack" mode, as evidenced by the red LED;
• damage to the electrical circuit from the button to the control unit;
• the system does not recognize the "ignition on" command. In this case, immediately contact the service center.

Is it possible to tie a key fob from another alarm to the Sheriff

In Sheriff signaling, the use of "non-native" remotes from security modules of this brand is allowed. May be the following compatibility.

1. Absolute: the communicator will function as "native", even the appearance is the same.
2. Full: all buttons are the same, only the design of the remotes differs.
3. Partial: the key fob is registered in the system, it will work for arming and disarming. Many customizable features are not available.
4. Missing: Pagers are completely non-interchangeable.

On the forums, you can find a compatibility table for Sheriff alarm panels, according to which the ZX 925 feedback key fob is replaced by models 900, 910, 930, 1000, 1050, 1055, 1060. You can also find out with which communicators the Sheriff car alarm 7000HHU and 1090, etc. .

People who torment dealers with the question of why the key fob on the Pandora alarm does not work, in most cases, owe their problems to their own inattention or laziness. Oddly enough, most people for some reason completely ignore the instructions. Note that, unlike most manuals, the explanations for Pandora are written quite sensibly and in detail.

If you are not too lazy to read them, then you will not have to spend time, nerves, or money on calls to the company that installed the alarm. However, for some reason, such a simple solution usually comes to our population's mind last.

First, a person panics and tries to accuse the world around him of injustice, and then he is sure that either there is no problem at all, or he himself is to blame for organizing it. Of course, electronics is a rather delicate thing and it is not difficult to damage it, but the new owners of Pandora sometimes have troubles, almost the next day after its installation. And this is unpleasant, especially if it soon turns out that they appeared solely due to their own inattention.

Why the key fob on the Pandora alarm does not work, subjected to physical or other influences - blows, rinsing in a washing machine along with trousers, chewing by a beloved dog - experts will understand. We will focus exclusively on the domestic side of the issue.

Correct registration

One of the most common complaints is that the key fob, they say, does not subscribe to the system. He will sign without any problems if everything is done as planned by the manufacturer.

• First of all, you need to make sure that the key fob is turned on. Initially, by definition, he is asleep, and to wake him up, you need to press the F symbol and hold it for several seconds until the corresponding melody sounds from the key fob (it is preceded by several single beeps);
• When programming, you should pay some attention to the number of presses of the service button, which selects levels, and then sublevels. If you dial a pin code without pressing the brake, you automatically find yourself at the level under the Roman numeral I. If this is not taken into account, it will be quite difficult to get to the right one;
• After registering each key fob, it is necessary to press the service button marked with one. Otherwise, the system will not store the entered settings in memory;
• After writing the settings to memory and before checking the effectiveness of the key fob, you need to turn the ignition on and off.

Compliance with such simple rules will eliminate any conflicts between the system and the remote control that controls it.

No response from the alarm

The main, inescapable and ineradicable reason for failure is a key fob that is not included. People keep forgetting that this is his original state. Especially often it manifests itself after replacing the batteries: such a tangible stress puts the control key fob in a passive state. And in the operating mode, it will not be superfluous to check whether the device is turned on: when pressed, say, with the keys in the same pocket as it, it could turn off. So at the first sign of a mismatch between the key fob and the alarm, first of all, press the F button for at least 3 seconds, waiting for the melody to play.

• If the key fob is on, but the alarm ignores it, go ahead;
• We check what we have with the battery. It is quite possible that she has not yet completely died, and therefore, the key fob shines, but the residual voltage may not be enough to transmit the signal;
• The key fob can simply jam like a frozen computer. In this case, its reboot will be effective: turned it off - turned it on.

The next step is a hard "reset". The battery is pulled out of the key fob for at least a couple of minutes. If the problem is in a glitch, the work will resume and remain regular for a long time.

Don't forget about the host base. Perhaps the contact between the wire and the RF module, which is glued to the windshield, has come off.

If none of the proposed gestures helped and there is a spare key fob, it is worth checking the overall performance of the system with its help. If the spare works, then the main one will simply have to be re-registered: the settings have gone wrong (for what reason, we are not interested). Thus, there are not so many reasons why the Pandora alarm key fob does not work - naturally, if the battery is charged, and he himself did not participate in any extraneous events.

If the system is specifically buggy and you can’t deal with it yourself, don’t fool yourself and go to the installer. After all, most dealers give a 3-year warranty on Pandora, so the trial will not cost you a dime.

The absence of an alarm on a car in the modern world can be a fatal mistake for the owner of the car. The statistics of theft is growing every year. Therefore, installing a security system is not a luxury, but a necessary need. Alarm manufacturers compete in an attempt to create the most reliable and functional device that will secure the car and make life easier for its owner. Modern alarm systems use certain codes that come from the control panel - key fob - to the system module and allow you to control some functions remotely. Moreover, each key fob has its own individual code. In some cases, it is required to reprogram and re-bind such a remote control. As a rule, the flashing process is described in detail in the instructions for the car alarm. However, if for some reason you cannot use it, please refer to our advice.

In which case it may be necessary to reprogram the alarm key fob

None of us is immune to loss. This also applies to car alarm key fob, which is also called an interactive pager. Most often, it is attached to a bunch of keys, so the risk of forgetting it somewhere is reduced. However, if this still happened, you will have to think about purchasing a new device.

With this remote control, you can remotely control the car alarm

Do not be alarmed, if you lose the key fob, it is not necessary to change the entire alarm system. An exception can only be cases if the alarm is quite rare, recently released or, conversely, outdated. It happens that the desired model cannot be found either in your city or in online stores. In such a situation, it makes sense to contact a car service: they can suggest a solution to the problem and direct the sellers of the system you need. If after that you were not able to purchase the required key fob model, you will have to completely change the alarm.

Please note that the new control panel must be selected not only in accordance with the brand of the security system, but also taking into account its type and model. So, the starline b6 keychain cannot be replaced with starline b6 dialog.

A new car alarm is usually programmed by system installers. In this case, you have nothing to worry about. The required code will be installed on all key fobs and linked to the system. But if you buy a car in the secondary market with an already installed car alarm, it already makes sense to take care of reprogramming the device.

The fact is that unscrupulous owners can give you an incomplete set of control panels, which means that you can easily turn off the security system and steal your car. Unfortunately, some scammers are already doing business this way. To avoid this problem, reinstall the code immediately after purchasing the machine.

Sometimes it happens that the key fob gets rid of the alarm for no reason. Many factors can cause this failure. Sometimes this happens due to erratic pressing of various buttons. If this happens to you too, don't worry. In most cases, the problem is solved by the same reprogramming of the key fob.

Typically, the kit includes up to 4 alarm control panels. If you decide to reprogram them, do it in a row with all the key fobs.

How to reprogram the signaling and bind it to the key

Please note that flashing almost any system begins with finding the Valet button or its equivalent. It performs functions such as emergency shutdown or alarm reprogramming.

Using the Valet button, you can turn off the alarm and program the key fob

This button is not on the key fob, but somewhere inside the car. It has a small size, and its location can be the most diverse. Moreover, it is often hidden in the most inconspicuous and hard-to-reach area of ​​​​the cabin, so that intruders who break into the car cannot turn off the system. Therefore, if you buy a car from your hands, ask the former owner about the location of this button. And in cases where a new alarm is installed on the car, the master usually asks the driver where it is best to place the device.

Valet button can be located almost anywhere in the car

Sheriff system

The Sheriff system is one of the most popular among motorists. It is distinguished by a high level of reliability and availability for sale. Replacing the alarm key fob and linking it will not take you much time.

The Sheriff key fob can be easily linked to the alarm and reprogrammed

1. You need to get into the car and lock it. Now set the ignition key to the first position.
2. Find the Valet button and press three times. If you did everything right, you will hear a long beep from the car alarm (not the remote control).
3. Repeat the previous point. This time, several short beeps will sound, followed by a long beep.
4. Press and hold the security activation button for a few seconds. A long siren signal will let you know that the operation was successful.
5. Wait 6-7 seconds. After that, the settings mode will turn off and you can bind another key fob to the system.
6. Carry out this operation with all devices.

Please note that the interval between all actions should not exceed 5 seconds. It is after this time that the pager exits the setup mode. So act quickly and carefully.

Video: Sheriff keychain binding

The Sheriff car alarm has a secret code function. If this function is activated, then you can start some processes only by entering the code. Usually the secret code is a two-digit number. You can find it in the instructions for the system. For example, for the Sheriff ZX 1050 alarm, the factory code is 11. You will need to come up with your own (any from 11 to 99). When setting a personal code, perform the following procedure.

1. Turn the ignition key and wait for the car to turn on. After that, you will need to turn off and then turn on the ignition again.
2. Now you need to press the Valet button as many times as indicated in the first digit of the code. With the factory code, the button only needs to be pressed once. Please note that this must be done in 10 seconds.
3. Turn the ignition off again, and then start it back.
4. After that, press the Valet button as many times as indicated in the second digit. With the factory code, this number will also be equal to 1. You also have 10 seconds to complete this action.
5. Repeat point #3.
6. If the secret code is entered correctly, one short siren signal will sound.
7. You now only have 5 seconds to set the ignition key to off. Next, you can create a new secret code.
8. Press the Valet button 5 times. You should hear 2 alarm beeps: a short one and a long one. They mean the launch of the code change function.
9. Press the button on the key fob to arm the car (looks like a closed padlock). You must do this no later than 5 seconds after completing step 8. One siren will sound. You have no more than 10 seconds for each of the following actions.
10. Press Valet as many times as indicated in the first digit of the new code. For example, you decide to set code 28. Then in this step you must press the button 2 times. After that, the same number of beeps will be heard.
11. Press the button to disarm the car on the key fob (looks like an open padlock).
12. Press Valet again as many times as indicated in the second digit of the new code. (8 times with code 28). You will again hear the corresponding number of beeps.
13. Switch off the ignition. The alarm will emit short and long sounds. They indicate that the system has exited programming mode.

Remember well, but rather write down a new code. However, do not leave a reminder of it in a conspicuous place. After all, knowing it, attackers can easily turn off the alarm and steal your car.

In the event that the car already had an owner, ask him about changing the secret code. After all, if this happened, the factory code will no longer be accepted by the system. Often, motorists forget to ask this question, lose contact with the previous owner of the car, and then fail to operate many of the vehicle's functions. In such a case, you will have to contact specialists.

Tomahawk system

The Tomahawk car alarm uses the Override button instead of the Valet button. Its functions are the same, and it will also be needed to bind and reprogram the interactive pager.

Model TW-9010 has a simple sequence of operations to bind to the car

1. Turn the ignition key, but do not start the engine.
2. Hold down the Override button and hold it until 4 beeps are heard. They mean entering the device setup mode.
3. Simultaneously press the button that opens the trunk, as well as the volume control. Wait for the car alarm to sound. If you are programming the first key fob, then there will be only one signal. If the second - two, and further to four.
4. Wait 5 seconds to exit setup mode. The binding of the remote control is completed.

A similar method is suitable for TW-9010 and TZ-9010 systems. To link key fobs of models Z-5, TZ-9030, TW-9030, X-5 to the alarm, you should use a slightly different procedure.

Model Z-5 has a slightly different principle of binding to the alarm

1. Set the ignition key to mode 1.
2. Press the Override button 7 times.
3. Turn the ignition key to mode 2. After that, you will hear 7 beeps, which means the start of the setting mode.
4. Simultaneously press the buttons that arm and disarm the vehicle (buttons with open and closed locks).
5. Hold them down until you hear beeps. The number of beeps will correspond to the serial number of the key fob (similar to programming other models).
6. Now you need to turn off the ignition. If all actions have been performed correctly, the parking lights will give 5 light signals. After that, the system will exit the setup mode. Also, programming will be disabled if you pause for more than 10 seconds.

Remember that all available key fobs must be tied at the same time. Also, for some systems, the function of checking the number of linked interactive pagers is activated. To find out this number, turn on the ignition, and then press the trunk release button. Pay attention to the number of LED flashes. It will correspond to the number of key fobs registered in the system.

Video: programming key fob model TZ-9030

In order to write a code to the X-3 system, you need to turn off the ignition, press and hold the Override button for 6 seconds. The rest of the steps are similar to the previous instructions.

Model binding X3 differs from Z5 in the principle of starting the programming system

SCER-KHAN MAGICAR 5 system

Unlike the previous two systems, the SCER-KHAN car alarm is able to remember no more than 3 control panels. If you start binding the fourth key fob, the first one will be automatically erased from memory.

The SCER-KHAN key fob can be activated using a pin code and without

There are 2 methods to bind an interactive pager:

• without a pin code;
• with pin code.

In order to activate the key fob without using a pin code, you need to perform the following operations.

1. Turn the key in the ignition lock three times, and then turn it off. You have no more than 4 seconds to complete this and each subsequent action. After that, the side lights of the car should give a light signal. It means that you have entered the alarm setup system.
2. Take the first key fob and press the button for arming the car (closed lock). You will see one flash of the alarm.
3. Take the second keychain and repeat the previous step. You will see another light signal.
4. The third key fob is programmed in a similar way. After it, you will see two flashes, and then the programming mode will be disabled.

If you decide to use the pin code method, then the procedure will be slightly different.

1. Repeat point #1 from the previous instruction.
2. Now you need to turn the key in the lock as many times as the first digit of the pin code.
3. Wait 4 seconds. You will see an alarm flash, which means that you are ready to enter the second digit.
4. Turn the ignition key again as many times as the second digit of the code.
5. After 4 seconds, you will see another light signal, which means the system is ready to register key fobs.
6. Not later than 4 seconds after the light signal, press the button on the remote control to arm the car. You will see one flash.
7. Repeat the same steps with the second and third key fob. After the last device, you will see two flashes and then the system will exit the setup mode.

Video: key fob binding SCER-KHAN MAGICAR 5

As you can see, in order to independently reprogram or link an interactive pager to a car alarm, you do not need to be a programmer or a car service worker. The principle of operation is approximately similar for all alarm models, with only slight differences in the number of button presses, the time intervals between this and the methods of giving a response signal. The whole process will take you no more than 5-10 minutes, taking into account the search for a secret button. By the way, in many car services, several hundred rubles will be asked for a similar procedure. Agree, there is no point in giving them away for something that you can easily do with your own hands.

If your old key fob is out of order, or you decide to buy an additional key fob, then you can do this by. Next, you have to program the Pandora key fob, that is, bind it to your alarm, you need to do this as follows:

Check if your keychain is on

To do this, click on the button with the image of an open lock on it.
- If the icon appears on the display: "Antenna", then the key fob is in the on state.
- If the numbers on the display light up, the key fob is turned off. In order to turn it on, press the button: "F", and hold until the third signal is heard. Keychain included.

Turn off the ignition

Enter the secret PIN number using the service button "Valet".

Press the jack button the number of times corresponding to the first digit of the PIN code. The LED should confirm the entry of the first digit with a red light. Enter the second, third and fourth digits in the same way. After the second and third entered digits, you should see the LED flash in red, after entering the fourth digit, the LED should blink Green-Red, which will indicate the correct PIN code entry.

Keyfob programming

Each Pandora keyfob has 20 seconds to program. If the time interval between key fobs lasts longer, you will have to start all over again.

Press Jack button 1 time. The siren should beep 1 time.
- If it is a keyfob with an LCD display: Press all 3 buttons of the keyfob at the same time and hold until the keyfob beeps 1 time. The siren should beep once, confirming that the key fob has been received.
- If this is a keyfob additional keyfob (without LCD): Press all 3 buttons of the keyfob at the same time, and hold until the LED blinks. The siren should beep once, confirming that the key fob has been received.

After all the key fobs are recorded, press the Valet service button once. Confirming the end of the recording, and letting the system know that this data needs to be saved.

The alarm key fob is the main command center of the car security system. With its help, the system is activated and turned off, with its help, a partial alarm setting also takes place. Key fobs are unique: each has its own program code, which transmits an access key to the main unit via a radio channel. Moreover, modern systems generate a new code every time to increase resistance to theft. But, like any technical device, the security system can fail. Therefore, the owner, in order to be a full-fledged owner of his car, must know how to reprogram the alarm key fob.

Why you need to reprogram the key fob

Flashing the key fob can be carried out for various reasons. For example, when buying a new car in which the alarm has already been installed. In this case, it is better to teach all available key fobs in a new way so that it is not possible to turn off the protection to unauthorized persons.

Of course, this may not be done, but when a used car with high theft rates or just an expensive one is purchased, such a procedure does not seem superfluous. Another case - the owner lost the key fob from the alarm. What to do in such a situation? Using a simple technique, link new control panels to the system.

The reason may also be various software failures, when the key fob starts to issue commands incorrectly or the system behaves inappropriately. Services for binding new key fobs are offered by many technical centers. How much does it cost? Depending on the complexity of the system itself and the car, such work is estimated at 500 rubles or more. However, this work is actually not as difficult as it seems, and with the clear implementation of all actions, it is quite possible to carry it out on your own.

Preparation for work

Before programming the alarm key fob, you need to familiarize yourself with the features of a particular alarm, as well as take into account some points. In case of loss or damage to the remote control, you must buy a new one without fail of the same model and the same company. Fortunately, unification among security systems is widespread, so there will be no problems with the main models and firms, and after linking to the main unit, you can use the remote control from another alarm, but only within the same model range. The model can also be identified by the key fob, such as the Ceturion alarm.

It should also be borne in mind that all available remote controls should be subjected to reprogramming. Otherwise, after the procedure, they cannot be tied to the main control unit.

All alarms are equipped with a special button for turning on the manual or service mode. It is called valet or override. With its help, you can set new parameters, reset all settings, force shutdown the system. Most often, it is hidden in the fuse box, near the steering column, at the bottom of the console, behind the glove box.

Entering programming mode

Enabling this mode on all alarms is done in the same way: using the valet button, turning the ignition on and off in various combinations, as well as a combination of pressing the buttons on the key fob, which are programmable. This combination is different for different manufacturers and it is wired into the system by default. If for some reason it has been changed, then it can only be restored programmatically, at the service station.

Programming of various systems

With this system, the sequence of actions for programming the alarm key fob is as follows. With the door closed and the alarm turned off, the ignition must be turned on. After that, press the valet button three times. A short beep of the siren indicates that the system has entered manual mode. These operations must be no longer than five seconds, otherwise the system will return to its normal state.

After that, you can move on to programming. To do this, press the valet button three times, while pressing button 1 on the remote control (arming the system). When a long beep sounds, it means that the remote control is bound. The new ones are programmed in the same way. After the procedure is completed, you can turn off the ignition or simply wait more than five seconds.

Security system Starline А91

For the alarms of this company, the algorithm of actions is similar. The valet button must be pressed seven times and the ignition turned on. The siren will chirp seven times and the backlight of the buttons on the remote control will light up. Now you can start reprogramming the key fob. To do this, hold down buttons 1 and 2 (arming and disarming). One beep confirms that the remote is paired. Subsequent consoles are programmed in the same way: two signals - the second, three signals - the third, etc. The programming mode is exited after 10 seconds and the turn signals will flash 5 times.

Alarms Starline series Twage A6, A8, A9

To enter the manual mode of these systems, the order is slightly different:

• Turn on the ignition
• Press the service mode button for 6 seconds(siren beeps 4 times)
• Buttons 1 and 2 are pressed on the remote control(one beep confirms that the first remote is registered)
• The second and subsequent remotes are programmed in the same way.. Manual mode will turn off after 6 seconds and the turn signals will flash 5 times.

Tomahawk system key fobs

In this case, the procedure is as follows:

• Turn on the ignition
• Hold down the valet button until the siren chirps 4 times
• Buttons 3 and 4 are pressed on the remote control(trunk opening and sound control) until the siren sounds. One squeak for the first, the second for the second, and so on.
• occurs after five seconds of inactivity.

Sherkhan alarms

To bind the new remote control of this company, the signals of the direction indicators are used. Within 4 seconds, you must turn the ignition on and off. Flashing turn signals means that the manual control mode is on. Immediately you need to press button 1 of the first remote control and the turn signals will flash once. Other remotes are tied in the same way: two flashes - the second, three flashes - the third. The programming mode switches off automatically after 4 seconds.

Now it’s clear how to program key fobs or bind new ones, and it’s not as difficult as it seems. What all of the above methods have in common is that all actions must be performed quickly, without delay, strictly within the allotted time. Even if you cannot enter the programming mode the first time, understanding the principle of the binding system will make it easy to cope with this task.

Keyfobs

The car alarm performs its functions either automatically or by remote control signals when the buttons are pressed

Some of the provided functions and some car alarm settings can be changed by programming.

car alarm

Keyfobs

The car alarm performs its functions either automatically or by remote control signals when the buttons are pressed. Some of the provided functions and some car alarm settings can be changed by programming.

Car alarm Star Line Twage A9 has a 3-button remote control with a liquid crystal display. The purpose of button 1 of the key fob is programmable

The purpose of button 2 is selected by quickly moving the cursor on the key fob display using button 3. When the key fob buttons are pressed, the fluorescent backlight of the display turns on for a few seconds.

When the StarLine A9 alarm system executes a key fob command, the corresponding information is displayed on the display and a melodic sound signal is emitted.

When the alarm performs any actions automatically, the corresponding information is also displayed on the key fob display and is accompanied by sound signals or vibration.

If more than one key fob is used to control the alarm, then the state of the car and the car alarm will be displayed only on the display of the key fob from which the last command was issued.

In case of inoperability or loss of the main key fob with two-way communication and liquid crystal display, the system is equipped with an additional 4-button key fob without feedback with a standard range. Most of the functions and operating modes of the StarLine Twage A9 alarm can be activated from this key fob as well, but the following operating instructions are written for the case of using the main key fob with an LCD display.

Button 1 Programmable command (0.5 sec) Remote start and stop of the engine (3 sec) Arming mode with the engine running (3 sec) Button 2 Command corresponding to the current position of the cursor on the key fob display (0.5 sec) Trunk unlocking (3 sec)

Button 3 Controlling the position of the cursor on the keyfob display (0.5 sec) Interrupting the keyfob notification signals (0.5 sec) Turning on and off the clock, alarm, timer, energy saving mode (3 sec)

Button programming 1 (6 sec) Buttons 1 + 2 Search mode (0.5 sec) Panic mode (3 sec)

Buttons 3 + 1 Key fob notification mode selection (0.5 sec) Buttons 3 + 2 Quick setting of the key fob timer (0.5 sec)

The LCD key fob uses an AAA, 1.5V battery. The battery life depends on the frequency of using the key fob, on the frequency of the pager operation, on the selected notification mode, on the type of battery installed. The capacities of commercially available batteries may vary by several times.

Accordingly, the average operating time of one key fob battery can be from 3 to 6 months

When the battery is low, an icon is displayed on the display, which indicates the need to replace the battery of the Star Line Twage A9 car alarm key fob. Battery replacement can be done by the owner himself in the following order:

Open the cover on the back of the key fob and remove the old battery. Briefly press button 1 on the key fob. Install a new battery, observing the polarity, and close the cover. (The correct position of the battery is indicated on the key fob body under the cover). After replacing the battery, correct the clock and alarm settings.

Re-programming button 1 of the key fob is not required. Button 1 Arming and disarming (0.5 sec) Control of channel No. 3 (3 sec) Button 2 Start and stop the engine (0.5 sec)

Extending the engine running time (3 sec) Activating the security mode with the engine running (3 sec) Button 3 Search mode (0.5 sec) Unlocking the trunk - channel No. 1 (3 sec) Button 4 Silently arming and disarming the security mode (0.5 sec) )

Channel #2 control (3 sec) Buttons 1 + 2 Panic mode (0.5 sec) Buttons 1 + 3 Disable shock sensor (0.5 or 3 sec) Buttons 1 + 4 Enable service mode (0.5 or 3 sec)

Buttons 2 + 3 Turn on the temperature trigger mode (0.5 or 3 seconds) Buttons 2 + 4 Turn on the daily automatic start mode (0.5 or 3 seconds) Buttons 3 + 4 Turn on the anti-robbery mode (0.5 or 3 seconds)

Keyfob recording in programming mode (3 sec)

The four-button key fob without feedback uses a lithium battery CR2032, 3B. The battery life also depends on how often the key fob is used and on the type of battery installed. When the battery is discharged, it must be replaced. Battery replacement must be carried out in the following order:

Unscrew the screw on the bottom cover of the key fob and open the cover. Remove the old battery and install a new one in its place, observing the polarity. Close the key fob cover and tighten the fixing screw. LCD display key fob car alarm StarLine Twage A9 Icons with letters - indication of commands, modes and alarm functions

Anti-theft mode (on/off) Auxiliary channel 3 (on/off) Temperature auto start mode (on/off) Daily auto start or alarm start mode (on/off) Remote engine start/stop (on/off)

Silent security mode without sound confirmation signals when the mode is turned on / off (on / off) Security mode with sound signals (on / off) Remote shutdown of the shock sensor

Service mode Valet (on / off) Indication of the state of the car and interior temperature Additional channel 2 (on / off) Remote trunk opening Icons with digital designation - indication of the status of the StarLine A9 alarm and the car

Key fob low battery indication Activation of additional channel 2 Auto start mode by temperature Engine started

Trunk open Doors open Vibration alert mode

Service mode Valet Automatic switching of the security mode Silent security mode Security mode with sound signals The hood is open

Impact on the body (level 1 or 2 shock sensor) Parking brake off 15. Locking the door locks Unlocking the door locks (including when opening the doors)

Standby mode (only the key fob receiver works) Indication of the transmission of a command by the key fob Call from the car Key fob power saving mode is on

Ignition on Alarm clock on Time of day - PM

Time of day - AM Daily auto start or alarm start mode Indication of time, temperature and auto start modes Indication of temperature scale (Celsius)

Countdown timer enabled Key fob button 1 programming

The purpose of button 1 of the key fob is programmable and can be changed by the owner of the car an unlimited number of times. For the convenience of using the alarm, it is recommended to program this button to turn on / off the armed mode.

Programming is done in the following order:

Quickly press keyfob button 3 two or more times to move the cursor clockwise or counterclockwise

To change the direction of cursor movement, make a short pause (1 - 2 seconds) between pressing button 3 on the key fob. By pressing button 3 of the remote control, set the cursor to the position corresponding to the desired command (for example, the command to turn on and off the armed mode with sound signals) Press button 3 of the remote control and hold it down for 6 seconds until 2, and then 3 more beeps appear.

Press keyfob button 1 to activate the selected function.

In the future, when using the alarm, a short press of button 1 on the key fob will lead to the execution of the command assigned to it (arming and disarming). When the button is pressed, the icon corresponding to the programmed function will light up.

Note

To reprogram the assignment of button 1, you need to do the described procedure again. Button assignment 1 will be changed to the new one.

Purpose of button 2 keyfobs

The purpose of keyfob button 2 is determined by the current position of the cursor on the keyfob display. The cursor is moved by pressing button 3 of the remote control in the following order:

Quickly press keyfob button 3 two or more times to start cursor movement. A pause and repeated quick pressing of keyfob button 3 changes the direction of cursor movement. When button 3 is pressed, the cursor will cycle through the icons indicated by letters on the display diagram.

Set the cursor to the position corresponding to the desired command by successive pressing of button 3 on the remote control.

Subsequent short pressing of button 2 of the remote control will cause the StarLine Twage A9 car alarm to execute the selected command.

Automatic return of the cursor position on the CHECK command

For the convenience of using the key fob and avoiding accidental activation of alarm modes and functions, 10 seconds after the last key fob button press, the current cursor position automatically returns to the CHECK command. The CHECK command for monitoring the state of the car and the temperature in the cabin does not change the alarm status and is the most frequently used in operation.

I want to tell you a little secret about the standard alarm key fob for Chery Fora (A21) and NiSSAN MAXIMA cars, this can also work for other models.
They asked a question about the problem of a standard car alarm, removed the battery or the battery was dead, and such a problem appeared, the key fob stopped controlling the central lock. The car starts up, which means that the immobilizer is working normally, when you press the buttons on the key fob, the red “peephole” lights up, which means that the key fob is intact and the battery in it is normal. This means that one of the reasons, most often the main one, is that the key fob has “disconnected” from the system. How to tie it back? Everything is much easier than you think.
Instruction:
1. Remove the car from the alarm (regular)
2. Open / close the driver's door
3.10 times turn the key from the “off” position to the “on” position within 15 seconds with the button pressed.
4. A beep will sound (may not sound).
5. Open / close the driver's door.
6. Press any button on the key fob.
7.2 beeps will sound.

To program all key fobs, repeat steps 5 to 7.
If one key fob is lost, all existing ones will have to be reprogrammed (maximum 4)
To exit programming mode:
8. Turn off the ignition.
9. Three beeps will sound.

That's all.
This information is not theoretical, it is practically worked out on several cars.

P.S.
Key fobs on Subaru are tied in a similar way.
link “http://www.subaru-faq.ru/faq/index.php?ELEMENT_ID=142”

How to “teach” a regular signaling to a new key fob? Answer: According to the available information, the “native” alarm system (Subaru Security System) is the Code Alarm alarm, you can search for key fobs by this name (then, of course, check for at least a visual match with the native one).

To “teach” the signaling to a new key fob:

1. Press the UNLOCK / DISARM button on the existing key fob
2. Open the driver's door, sit on the driver's seat, close the driver's door
3. insert the ignition key into its lock and turn it 10 times from the LOCK position to the ON position and back in 15 seconds. Stop in the LOCK position. The signaling will beep once - the system is ready for programming on a new key fob.
4.no later than 45 seconds later, open the driver's door. Close it again.
5. Press and release any button on the new key fob. The signaling should blather twice, indicating that the key fob is registered in it.
6. If you need to program more key fobs, return to step 4. In total, up to 4 key fobs can be recorded in the system. If you don't need it anymore, go to the next step. It is recommended to register all 4 key fobs (if there are not so many, then several times the available key fobs) to be sure that there are no old key fobs left in the signaling.
7. Remove the key from the ignition switch. The alarm should chirp three times, indicating that it has exited the programming mode.
8.Check all newly programmed keyfobs for operability.

To remove a keyfob from the system (for example, in case of its loss), program all 4 keyfobs in the same way (the old ones will be deleted from memory). If there are no 4, but there is, for example, only one, write it 4 times. And you will be sure that there are no other key fobs in the signaling.

When prescribing key fobs, make sure that no one is hanging around and trying to prescribe another key fob for you at the same time.

To make it easier to control the car alarm, drivers use a command key fob. This radio transmitter encodes information. The received code is perceived by the control unit. Often, drivers have to change the type of radio transmission. This requires key fob programming. It is important to remember that each system has its own reprogramming technology.

In this article you will learn how to reprogram the key fob

The need for reprogramming

There are various reasons when keyfob programming is required. For example, when a user bought a new car with an alarm already installed. In this case, it is better to reprogram the key fob so that unauthorized persons cannot turn off the protection.

Of course, you can do without flashing, but if you buy an expensive car, such a procedure will not be superfluous. Also, such a procedure is an exit in case the owner loses the key fob from the alarm. The question of how to program the key fob becomes relevant in case of software failures. For example, when the device incorrectly gives commands.

In this video you will learn how to reflash the key fob:

The price for such a service depends on the complexity of the system. The average cost of reprogramming is 500 rubles. However, such work is simple, and by following the instructions, the user can perform it himself.

Preparation for the procedure

For those who are wondering how to reprogram the key fob, it is important to remember that preparation for such a procedure is necessary. To do this, you need to follow these steps:

1. In case of loss of the key fob, you need to purchase a new device only of the model that was bundled with the installed alarm.
2. If multiple radio transmitters are used to control the system, they must be reprogrammed at the same time so that they can be linked to the new control unit.

Many vendors include instructions with the kit. At the same time, the user may experience difficulties when there are no tabs with a translation of the instruction into Russian or it is written with errors (if the device was manufactured in Korea).

The motorist must first of all read the attached instructions. This document should show the device of the console. If there is no manual, the user should follow the generally accepted instructions.

Core technology

Key fob reprogramming technology is simple. To do this, you need to perform the following actions:

1. Having installed the key on the lock, the user must activate the ignition. Starting the power unit is not required.
2. Next, you need to simultaneously press with one hand on the button with the loudspeaker and on the button with the image of the luggage compartment. With the second hand, press the "service mode" button.
3. When the speaker beeps 5 times, you can release the pressed button.

Having correctly performed the proposed actions, the motorist must again press the button with the image of the loudspeaker and the button that opens the luggage compartment. As a result, the turning lights should flash several times.

It often happens that as a result of these actions, the key fob is still not programmed. In this case, you can repeat the reprogramming along with the recording of the key fob. Another way is to reprogram the key fob without a code. . To do this, follow these steps:

1. Within a few seconds, you need to connect and turn off the ignition system 3 times by turning the key.
2. If the motorist did everything right, he will see a single flash.
3. After the flash is fired, the owner will have 4 seconds to press the communicator registered in the memory.
4. After recording on the first electronic remote control, the user can press the key of another key fob.
5. Information from the third key fob must be entered into memory in the same way. During the recording of the last remote control, the information from the first device will be deleted automatically.

After the last remote control has been reprogrammed, you need to wait a few seconds. This is required to log out.

Setting up the Sherkhan alarm

Before working with the Sherkhan alarm system, you need to disarm the system. Next, you need to perform the following steps:

1. First you need to press the Vallet button so that the alarm flashes.
2. Next, press Vallet again. As a result, the LED will start flashing.
3. After that, you need to press Vallet as many times as there are digits in the pin code. This step must be repeated for all digits of the pin code.
4. An alarm will flash 6 seconds after the last digit of the code has been entered. Thus, the system will confirm the readiness to enter the code.
5. Within 4 seconds, you need to briefly press the fourth button on the first key fob 2 times. If the recording is successful, the alarm will automatically flash.
6. After that, you can enter the codes of the remaining key fobs. If the code is entered successfully, the alarm will flash.

To exit the reprogramming mode, no action is required for 5 seconds after the last code has been written. As a result, the alarm will flash and the system will exit the reprogramming mode.

Car owners additionally install car alarms. The Starline A91 signaling model is popular among motorists. Among the advantages of the system are a shock-resistant remote control, many functions, wide compatibility and programming of your own commands. In addition, the security alarm system with feedback locks the doors and turns off the engine ignition, which greatly complicates the car theft.

Below is an overview of the key fob, system settings. How to independently register car alarm commands, synchronize with the car, activate or reflash the device, learn from the article.

Starline A91 keychain functions

The device has a set of commands. A rubberized keychain (see photo) alarm with a small screen reacts to attempts to enter the salon without keys. The system also performs security functions.

Among the main alarm commands A91 are listed.

1. Security actions. The system turns off the ignition, locks the doors and the hood lock. This prevents car theft, battery theft.
2. Automatic heating of the power plant. You can program the engine to turn on at the right time and bring it to operating temperature. Additionally, you can assign interior heating.
3. Setting system options. The owner can prescribe the time for oil changes, scheduled repairs, etc. During operation, the screen will show how much is left before the necessary procedure.

Alarm control methods

The multifunctional key fob system offers several options.

1. Button 1 activates the standard security mode. Auto will squeak after mechanical impact.
2. The second button on the key fob removes the car from this mode.
3. If you sequentially press the first and second button, then the silent protection will be activated. The machine will not respond to the impact, but the owner will receive messages displayed on the key fob screen.
4. Double pressing the first button sets the car under protection without sound, and double pressing the second button - disarms it without a signal.
5. Pressing the first and third keys of the key fob will arm the car with the engine running.
6. The third button allows you to find out about the current state of the car and its settings: interior temperature. A double click will provide additional information about the engine temperature on the key fob display. Auto search mode will be enabled.

How to register a Starline A91 keychain

Linking a new system remote control is done in a simple way. You can register a key fob for the Starline A91 alarm to the car yourself.

Step by step instructions for connection.

1. Insert the ignition key. Turn it off, and after 7 times press the Valet key.
2. Now turn on the ignition. The alarm should make 7 sounds. After the siren is silent, the key fob binding mode is activated.
3. Simultaneously press the buttons 2 + 3 and hold them. One system beep sounds. Let's release the keys.
4. If several remotes go to the alarm, but it is necessary to bind each of them. We repeat the procedure (point three) for each device. The maximum number of key fobs that can be connected to one car is four. After each binding, one siren will sound.
5. We turn off the ignition. The parking lights flash five times in a row, which indicates that we were able to reprogram the car alarm system.

Key fob programming Starline A91

Learning how to use the alarm remote control is easy. Above, we gave instructions for programming key fobs. However, the functionality of the system is wider. You can customize your alarm.

Button 1 on the key fob is responsible for the following system commands.

1. Activation of the security mode (one click).
2. Silent security (two consecutive clicks).
3. Locking doors when the engine is running (one touch).
4. Enable/disable shock sensor (double tap).

1. Exit from the alarm mode (1 click)
2. Disabling the silent guard (2).
3. Additional shock sensor (2 clicks).
4. Opening doors with the engine running (1).
5. Interrupt alarm (1).
6. Anti-robbery mode (2).

1. Cabin temperature indicator (1).
2. Search mode (2).

A long press records additional system commands: auto start by alarm, turbo timer, immobilizer and much more.

You can learn about the correct key fob firmware from the video.

How to easily tie a key fob to a Starline A91 alarm

In total, the car is trained to work with four system remotes. If you program a new alarm key fob at number five, the device will automatically replace the old Starline device with a new one. This must be remembered so as not to think that the old remote control has stopped working.

Activation of the key fob on the Starline alarm

Here you can watch a video with detailed instructions for programming Starline remotes, their registration, binding, setting commands at the request of the driver.

Why the Starline A91 keychain is not registered

Sometimes the owners have a problem that the remote control has “got rid of” or the commands are not registered. You need to check the integrity of the battery. If the key fob indicator flashes, then the system commands may not reach the control unit. Battery needs to be replaced.

Or, if the number of key fobs in the system is already more than 4, then the previous alarm remotes begin to be deleted on their own. Then you need to reprogram the device by linking it to the car. If things don't work out, take it to a service center for a flashing.

How to reset the settings on the Starline A91 alarm

It happens that the remote control is faulty. Then you should drive to the service center to update the firmware of the Starline key fob. First you need to reset the alarm settings. If the individual trip code was not programmed, then the following actions must be performed.

1. Open doors with a key. The dimensions of the car will flash 4 times.
2. Turn on the ignition. Get to the Valet button, press it three times.
3. Switch off the ignition. The siren should sound.
4. Now you can start the car and get to the officials to flash the Starline alarm key fob.

Ways to unlock the Starline A91 keychain

If the remote control malfunctions, turn it off. You can use the individual code programmed earlier.

• open the door with the key. The car will blink the turn signals 4 times;
• turn the ignition key by pressing the Valet button the previously set number of times;
• write the system startup code. The Starline remote should vibrate slightly;
• turn off the ignition. We receive confirmation from two flashes of turn signals;
• the system is deactivated, you can go.

Starline A91: additional (spare) key fob

The alarm system has two remote controls - the main and the secondary (see photo). The main key fob has a remote antenna, a color screen informing about the current state of the machine, three buttons on the side.

An additional or spare remote control is different from the main one and is necessary in case of loss of the first or dead battery. There is no screen on this keychain, and it cannot communicate with its owner - a device without feedback. Remote control buttons on the flat side, they retain all functions. With a spare key fob, you can open the doors. The second remote control will help and unlock the interior or turn on the auto start of the engine.

Replacement key fob Starline A91

During operation, the original remote control may fail. Then you need to replace the Starline key fob. You can buy it online, offline stores or directly from official representatives of the company.

Starline keychain prices

You can buy a standard remote control in any city in the country. The price of Starline A91 fluctuates between 1000-3000 rubles, depending on the distance of the seller or additional services.

Signaling benefits:

• versatility of design - compatible with almost all cars with manual or automatic transmission;
• complex encryption system;
• increased range;
• versatility and long warranty periods.

How to set up and set the time on the Starline A91 alarm key fob

When linking the remote control to the car, you need to set the clock. After replacing the battery, it is advisable to re-set the time, because when it is removed, everything is reset. To perform such a procedure, you must perform the following steps:

We press the button three keyfobs.

After a triple signal from the remote control, set the clock by operating with buttons 1 or 2. These two keys are responsible for increasing or decreasing, and the third one selects the hours and minutes.

After the correct installation, stop pressing anything. The Starline alarm key fob will sound once and the current time will be recorded.