Scher-Khan Magicar V - user manual. Scher-Khan Magicar 5 scher khan car alarm programming

Programming the Sherkhan 5 key fob may be needed in the following cases:

1. The alarm does not turn on and off from one remote control, others work fine.
2. Hull damage or printed circuit board switch.
3. Incorrect operation of the main unit and remote control.
4. Use of additional key fobs.

Three pagers can be stored in the memory of the anti-theft system. This is not difficult to do, but the procedure has its own characteristics.

Binding a new key fob to the Scher Khan Magicar 5 alarm

The instruction manual will help you to record a new communicator into the memory of Magikar 5. Please read it carefully before performing any operation on the remote control.

The key fob of the anti-theft system can be programmed only when the security mode is disabled. If you are connecting new remotes, do not forget to overwrite the old ones, otherwise they will be deleted from the system memory.

1. For four sec. switch the ignition on and off three times. The lights will flash once. The programming mode has been entered.
2. Enter the remote control code by pressing button 1. This must be done within four seconds. The vehicle lights will turn on once.
3. If necessary, record the following switches in the same way.
4. Do nothing for four seconds after programming the last remote control and the system will automatically exit the settings.

Firmware and reprogramming Sherkhan 5

You can reflash the Magikar 5 version keychain using a PIN code. Record remote control codes by following the instructions below.

1. Turn the ignition key from "Off" to "On" three times within four seconds. Switch off the ignition.
2. Switch the ignition back on within four seconds. The number of inclusions must match the first value secret code. The light optics will light up once, confirming that a second value can be entered.
3. Turn on the ignition. The number of inclusions must correspond to the second digit of the code. The "emergency" flashes once, confirming the correct action.
4. Enter the rest of the secret number in the same way.
5. After entering all the numbers, press button 1 of the switch. The lights will flash once, confirming the pager entry. After four seconds, the system will exit programming mode.

An additional Magicar 5 keychain is not prescribed: reasons

There are frequent situations with the anti-theft system communicator when it is not programmed. There are a number of reasons for this:

• the remote control is damaged;
• the "Jack" mode is activated;
• the system does not recognize the "ignition on" command.

If it is not possible on your own, having tried all the options, register the key fob, you should replace it with a new one or contact service center.

Autorun setup instructions

Starting the engine is a very convenient function of the security system. Having carefully studied the instruction manual, every motorist will be able to start the car from the key fob on their own. Before programming, disarm the car, turn off the ignition, turn off the "hands-free" mode, just in case, open one door.

Time setting.

1. To enter programming, simultaneously hold down keys 1 and 2.
2. Enter the timed autorun settings by pressing button 4 thirteen times. After each press, the system should emit a single beep.
3. You are taking right time auto start: button 2-8 hours, 3-4 hours, 4-2 hours.
4. Then start the timer by pressing buttons 2 and 4 at the same time. The display will show the “timer” symbol.

Automatic start of the engine by temperature.

1. Enter programming mode: buttons 1 and 2.
2. Press the 4 key twenty-one times.
3. You are taking required temperature: key 2 - (-15), 3 - (-25), 4 - (+60).
4. Start the timer by pressing 2 and 4 at the same time. The display will show “timer”.

How to remove the Jack mode without a keychain

On the Sherkhan alarm, it is quite easy to accidentally turn on the “Valet” mode by accidentally pressing it. Very often this is mistaken for a system breakdown: the alarm does not respond to shocks, autostart fails, key fobs are not programmed, the LED is constantly on. Only central locking and trunk opening works.

To turn off the "Jack" without a key fob, use the multifunctional button located in a prominent place.

1. Turn on the ignition, do not start the engine.
2. Hold down the multifunction key for two seconds. "Valet" is disabled.

Are all Sherkhan Magicar 5 keychains interchangeable?

The alarm panel is such a thing that is constantly lost, forgotten, broken, falls into the water. It is not possible to connect a second key fob due to its absence. Replacement with the original remote is also unrealistic. You have to look for a family communicator more or less compatible with yours. The pager may be completely, partially, or not at all. The compatibility of key fobs of the Sherkhan Magikar 5 anti-theft system was considered by us.

Video help to activate remotes

Of everything model range alarms with autorun Scher-Khan the most unfortunate is definitely Magicar 5. This is connected not only and not only with the hacking vulnerability common to all Scher-Khan systems of these years, but also with the extremely illogical implementation of autorun. Even the classic and most convenient “software neutral” for raising the handbrake cannot be physically implemented here, there is no input for the handbrake.

In the same way, the most accurate analog method for monitoring engine operation using a tachometric signal is not provided. So best recommendation owners of such systems will have to replace them with more modern ones that work adequately with autorun and persistent co.

Nevertheless, many motorists continue to use previously installed (usually in car dealerships) Magicar 5, and during operation, questions inevitably arise - from how to set up the Sherkhan Magicar 5 key fob to how to disable autorun on Magicar 5 (by the way, correct reading- "magicar").

An auto electrician-diagnostician, a certified StarLine specialist, works on the site. If you have questions about car alarms, ask them at the end of the article in the comments or Vkontakte. When contacting, indicate the make of the car and the model of the alarm.

Keyfob programming

Although “falling off” key fobs are mainly the prerogative of the Logicar line, where the need for regular re-registration has become a byword for a long time, there is a possibility of loss of recognition here. It is not difficult to register the Sherkhan 5 keychain, it is enough to remember a simple procedure.

First of all, you need to remember that the entire set must be rewritten: at the beginning of the procedure, the memory of all previously stored key fobs is erased. If a problem arose on the road, when you only have one key fob with you, you should repeat the procedure upon returning home, but with complete set- otherwise, if the main key fob breaks, you will have to open the car with emergency disarming of the system. On all prescribed key fobs with an LCD screen, you need to turn off the " Free hands” (holding button 1 for two seconds), and the system is disarmed.

Key fob programming is performed in three stages:

1. Quickly turn the ignition on and off three times, after which the light alarm should give one flash.
2. Switch on the ignition again, leaving it in this state.
3. With a pause of no more than 4 seconds, alternately press buttons 1 on all prescribed remote controls (no more than three).

Exit from the keyfob assignment mode will occur automatically 4 seconds after the last press.

Re-prescribing- one of the most effective measures in case the Magikar 5 key fob does not work. Only after making sure that there is no physical connection (that is, the key fob cannot be registered), you need to look for a problem in the system or change the key fob.

Time setting, autostart by time

timer start (A);
turbo timer mode (B);
passive activation of the system (C);
automatic activation mode without pressing the buttons (D);
included siren (E);
shock detection sensor (F) is off;
vibrating alert is active in the key fob (G);
control of door locks after starting the ignition (H);
open trunk lid (J);
the engine is switched on in the autostart mode (K);
system state (L);
open doors (M);
field for displaying hours, temperature and data during autorun (N);
operating mode Valet (O);
working alarm or dimensions not switched off (P);
shock sensor triggering (Q);
key fob battery indicator (R);
signal level (S).

Since the alarm has a timer autostart mode, when the car starts every day at a specified time, for its operation it is necessary to correctly set the time on the main key fob. The procedure for setting the time on the Sherkhan Magikar 5 alarm key fob:

1. Hold down buttons 2 and 3 for 2 seconds. The display will change to something that looks like "Pro9" (actually it should be Prog, but due to the limitations of the seven-segment screen elements, it looks like this).

2. Briefly press button 1 - the current time will start flashing, the key fob will give a single signal.

3. Press button 2 to set the hours, use button 3 to enter the minutes.

Autorun by time(of course, all the right connections and the settings of the system itself must be made in advance) is possible in two versions. Or the car starts every day in set time(for which the clock is set), or this happens every 2, 4, 8 hours from the moment the mode is activated and regardless of the clock setting. The type of timer autostart is set in the system settings, that is, several options cannot be activated at the same time.

To enable autorun by timer for 24 hours, you need:

1. Hold down buttons 2 and 3 for 2 seconds.

2. After the inscription “Pro9” appears, briefly press button 2 (not 1, as for setting the current time. The indications of the previously set autorun time will start blinking.

3. Use button 1 to set hours, button 2 to set minutes.

5. Press buttons 2 and 4 to turn on the TIMER indicator on the screen.

If you need to change the autorun time when the timer is already activated, you must first disable it (similarly, by pressing 2 + 4), set the timer time, then enable it back.

If the alarm settings are set to run periodically, just press the 2+4 buttons to turn on and off. After activating the intermittent start mode for the first time, the engine will start after 2, 4 or 8 hours, depending on the settings of the central unit.

Video: SCHER-KHAN MAGICAR 5

Auto start by temperature and voltage

Since Sherkhan Magikar 5 (in the generally accepted meaning) does not allow autostart by temperature, it is only possible to limit the periodic start. In other words, the car will try to start every 2, 4, 8 hours if the following conditions are met:

• the temperature at the installation point of the central unit is lower than the specified threshold;
• the battery voltage is lower than the set threshold.

You can set one of these conditions, or two at the same time. Their programming is described below.

Alarm settings

To change the system settings, any of the previously registered key fobs is used. The car must be disarmed, ignition off.

The system has two separate settings menus. The entrance to the first menu is performed by pressing and holding the buttons 1 + 2, the second - 1 + 4. After the sound signal, you need to select the function number by pressing button 4 and make a short pause, after which the machine will give the number of the selected function with siren signals. With buttons 1,2,3 and 4, you can then set the desired value of the function.

In menu 1 The following functions are associated with the work of autorun:

• 12: Engine warm-up time at auto start, 5,15,25 or 45 minutes for settings 1 to 4 respectively.
• 13: timer start type. In value 1, the launch occurs every 24 hours according to the time set on the key fob, in values ​​2.3 and 4 - every 8.4 or 2 hours from the moment of activation.
• 14: Limit the number of autostarts, maximum 5, 7, 16. When set to 4, the number of starts on the timer is not limited.
• 16: autorun reservation type. In option 1, the ignition interception occurs every time the ignition is turned off, but with a noticeable pause during which the engine may stall. Option 2 introduces additional condition: The doors must be closed. If you do not need autostart reservation at a particular moment, it is enough to first open the door and then turn off the ignition. There is also a delay before the ignition is intercepted. Therefore, the only adequately working backup option on the Magicar 5 is manual backup (function value 3), when you need to press and hold button 2 of the key fob before turning off the ignition.
• 17: a way to complete the "software neutral" algorithm. In option 1, the car will stall after closing the door without arming, in option 2 it will be similar, but with auto-arming. In option 3, the engine will stall only after manual arming. This is the only way to use.
• 20: Limit periodic triggers based on battery voltage. In option 1 it is not set, option 2 sets the threshold to 11.5 V - until the voltage drops below, the start will be blocked. If you choose to run every 24 hours, the setting is ignored.
• 21: auto start temperature threshold. In option 1 it is not installed, in options 2-4 the temperature is set to -15, -25 and 60 degrees, respectively (the last option is for the air conditioner to work in the heat).

Menu 2 autorun needs settings:

• 12: minimum starter rotation time, 0.6, 0.8, 1.2 or 2 seconds. It should be set to the minimum possible, since there is no automatic cut-off of the starter, as on alarms with a tachometric input.
• 13: maximum time starter rotation, 2, 4, 8, 10 sec. It should also be as low as possible to save the resource of the starter and the flywheel ring gear.
• 14: increase in starter rotation time on subsequent attempts to start after an unsuccessful one. In option 1, each new start attempt lasts 0.2 s longer than the previous one, in option 2 - by 0.4 s. Option 3 sets the fixed scroll time given by function 12.
• 15: pause between ignition on and start attempt, 2, 4, 8 and 10 seconds. The first two options are relevant for gasoline engines, options 3 and 4 are for diesel engines with glow plugs.
• 16: pause after stopping the engine until the ignition is turned off. 0, 4, 15 seconds or 4 with restart attempts.

The remaining autorun settings are related to the connection scheme for a particular car and should not be changed by the user.

The instruction manual attached to Sherkhan Magikar 5 consists of sections devoted to setting up and installing the security complex. The documentation has been translated into Russian, there are additional graphic explanations that allow the driver to adjust the alarm on their own.

Specifications

Technical parameters of Scher-alarm Khan Magicar 5:

• frequency range - 433.92 MHz;
• transmitter power - no more than 10 mW;
• communication range of the communicator - up to 1500 m;
• current consumption - up to 35 mA;
• mass of the central block - 270 g;
• supply voltage - 9-18 V;
• product protection class - IP40 (except for the siren).

Equipment

In a set of automotive sherhan alarm Magic Car 5 included components:

• head unit with processor and relay units;
• communicator with 2-way communication channel;
• auxiliary console;
• shock sensor;
• driver call shock sensor;
• antenna unit with connecting harness;
• temperature sensor;
• separate relay with mounting block;
• siren and additional limit switch;
• kit power cables with connectors;
• instructions for installation and configuration;
• sticker set.

Functions

Alarm with auto start Scher-Khan 5 has the following functions:

• support for supercharged engines;
• disabling password protection;
• 2-stage deprotection;
• giving alarm signals with lamps and a siren;
• automatic and remote start of the motor;
• joint work with standard blocks of the central lock;
• additional channel for controlling the luggage compartment lock;
• automatic activation of protection;
• cabin light off delay mode;
• support for the protection of a car with a running engine.

Panic and JackStop modes

To enable the function, a long action on the IV button is used (the type of activated mode is indicated when programming the processor unit). If the alarm has been disabled, then when a signal is received, the doors and start circuits are blocked. Sound and light alarm is activated, which lasts 90 seconds. When the Panic function starts, all programmed algorithms are canceled automatic start engine. To disable the modes, briefly press the buttons marked I and II.

Hands free mode

The design of Magic 5 provides for the possibility automatic shutdown and the inclusion of protection. When the alarm mode is active, the alarm responds to the radiation of the transmitter, which is captured at a distance of 15 m. When the owner moves away from the car, automatic arming occurs, and when he returns, the protection is turned off.

To activate the "Hands Free" mode, you need to perform a long press on the I button. After the icon with the text Auto appears and the melody is broadcast, you need to briefly press the IV button. An icon with the text "Holy hands" is turned on on the scoreboard. The mode is deactivated by long pressing the I key.

Valet mode

When transferring the car to a service station, the mode of temporary disabling of the security functionality is provided. To turn on, use the complex pressing of the keys I and III, which are held for 2 seconds. When the function is activated, the ability to control the door locks remains, the icon in the form of 4 letters Z is turned on on the communicator display. Repeated long-term pressing of the buttons allows you to disable the mode.

Advantages and disadvantages

Advantages of car alarm Scher-Khan 5:

• no failures in work;
• a small number of false positives;
• signal reception range;
• automatic engine start;
• long battery life in the communicator.

Disadvantages of equipment noted in the reviews of the owners:

• interruptions in operation at air temperatures below -35 ° C;
• there is no cellular communication block;
• a simple encoding algorithm that is opened by signal scanners;
• there were cases of involuntary triggering of the owner's call sensor;
• the standard siren has a low volume;
• Chinese copies are common on the market, imitating the original packaging and products.

Installation instructions

The algorithm for "dummies" is given in the factory documentation:

1. Place the antenna unit in the corner part of the windshield; it is allowed to mount the unit under the interior trim. If the owner installs the unit discreetly, then the range of the remotes may be reduced (due to antenna shielding).
2. Place the call sensor on the surface of the windshield, the installation point is preliminarily degreased.
3. Mount the siren under the hood of the car. The node is located at a distance from sources of heat and moisture.
4. Locate additional limit switches in areas not exposed to moisture.
5. Fix the processor module inside the instrument panel. Screws or plastic clamps are used for fastening. Equipment shipped from the factory does not have key fobs stored in memory. Before use, it is required to program the remote control codes.
6. Glue the shock sensor inside the car (on a metal base). Provide free access to the sensitivity adjustment rotary potentiometer in advance.

Wiring diagram

After the installation is completed, connect the Sherkhan 5 alarm to onboard network and interconnect the electronic blocks. The instructions include a connection diagram, before starting the connection, you should study the documentation. The connectors use cables equipped with insulation different color, which allows you to determine the purpose of the cord. Cable connection points are protected insulating tape, it is necessary to provide protective fuses (mounting locations and rating are indicated in the diagram).

How to use the alarm

The User's Guide that came with your equipment contains a section on how to use your device. There is a separate chapter describing the functioning of the security complex. The driver of the car is recommended to study the manual, and then draw up individual sections (for example, a description of the emergency shutdown algorithm) in the form of a memo that is stored along with the documents for the car.

Symbols on the display

Before you start using the alarm, you need to remove the safety insert glued on the contacts of the communicator. When the battery is correctly installed, a melodic signal is given, indicating that the device is ready for operation.

On the LCD screen of the Scher-Khan 5 alarm communicator there are symbols for displaying:

• the state of the battery;
• operating mode of the device;
• fields for displaying hours;
• protection mode status indicators;
• siren operation mode icons and shock sensor;
• explanatory inscriptions when the engine is actively started by a timer or a turbo timer is running;
• indicators open panels body;
• turning on the "Hands free" mode;
• the icon of a call coming from the car;
• indication of the operation of lighting equipment or a power unit;
• service mode activation signal Valet.

Button assignment

The buttons located on the communicator support 4 modes of operation:

• short exposure;
• long (more than 2 seconds) pressing;
• fast complex action on 2 keys;
• long-term joint holding of 2 buttons.

The driver, by pressing the buttons of the communicator or auxiliary remote, turns on or off the security mode, activates the remote start and other functions. The keys are used to configure the remote control with a display, are used during programming of the central unit. The purpose of the buttons is indicated in the relevant sections of the operating and configuration instructions.

Time setting

To program the clock, a joint long press on the II and III keys is performed, and then the driver enters the settings menu (by briefly pressing the I button). To adjust the values ​​of hours and minutes, the keys I and II are used, to store the result in memory, a long action is made on II and III (until the buzzer sounds).

Arming and disarming

To turn on the alarm, you must press the I key. A siren will sound, external lighting will work, and then the engine start circuits will be blocked and the locks will be locked. Explanatory icons appear on the communicator display.

To disable the protection, the II key is used, the complex gives a double signal with a siren and external lighting equipment.

The control diode turns off, the icons in the form of car headlights and a lock with an open shackle flash 5 times on the display.

Remote start from key fob

The start is made by a long action on the button II. After the locks are locked, the engine starts, the display of the communicator shows the remaining operating time (pre-programmed). The driver can disable the security, place the key in the lock, and then activate the ignition and start driving. You have 20 seconds to complete the action, otherwise the engine will turn off.

Trunk opening

car alarm Scher-Khan Magicar 5 allows you to control the lock of the luggage compartment lid, to unlock you need to long press the button III. At the same time, the security mode is disarmed and the doors are unlocked. The driver can program a mode in which the side doors remain locked or the armed mode is not disabled (the lid limit switch and the shock sensor are temporarily turned off). In this case, after locking the lid, the protection is automatically activated.

Silence the siren

A complex short-term pressing of the keys marked I and II allows you to turn on or off the signaling of the siren and lamps. The value of the function is preset when programming the block. When the silent mode is enabled, the communicator's buzzer remains active. After the mode is canceled, the icon with the image of a playing pipe turns on on the screen.

Programming instructions

Before starting the setup, the security mode and the “Hands Free” function are disabled. To start the setting, a long press on the buttons I and II or on I and IV (to enter table 1 and 2, respectively) is performed. Then, by successive pressing (corresponding to the function number) on the IV button, a section is selected. The security complex gives siren signals confirming each keystroke. After entering the section, an additional signal is given by lamps and a siren (according to the serial number of the function).

The programming table given in the documentation contains explanations that allow you to correctly set the parameters. By pressing the buttons mounted on the communicator, the driver selects the desired parameter value (confirmed by the siren and flashing alarm). To set up each function, you need to go through the entire algorithm again.

How to enable autoplay

To activate autorun, it is required to perform a complex action on the key fob buttons marked with numbers II and IV. The message Timer will turn on on the remote control panel, the frequency of repetitions is indicated in advance in the programming menu of the processor unit. Car alarm Sherkhan Magic does not allow simultaneous activation of 2 modes.

To ensure that the motor starts on a timer, it is necessary to set the clock and the operating parameters of the alarm clock. After pressing the buttons II and III together, the inscription Pro9 is activated on the display, further pressing the button II turns on the timer adjustment. The driver uses the buttons marked I and II respectively to change the hours and minutes. After adjusting the parameter, press the keys II and III.

The Sher Khan Madjikar 5 complex supports starting from external equipment. Additional programming of the processor unit is required to enable the motor to turn on. To save battery life, the number of restarts is set, the driver programs the number of repetitions, and the restriction can be removed.

The equipment supports starting on a signal from temperature sensor located in the cabin, or critical voltage in the car's onboard network.

Before using the function, it is necessary to enter the threshold values ​​by programming the central unit. Simultaneous activation of automatic start by timer, temperature and voltage is allowed. The motor starts when the parameters fall below the threshold, but the repetition rate is limited by the timer settings.

Faults and their elimination

When the control panel and the head unit are out of sync, the command translation process is disrupted. The algorithm for re-entering the remote into memory depends on the settings of the head unit. To start the procedure, you need to turn the ignition on 3 times, and then turn the key to the "Off" position. After the flash is fired by external lighting equipment, the I button on the programmable remote control is pressed, and then, by analogy, the remaining devices are recorded (no more than 3). Each step of the procedure takes 4 seconds.

If a password entry algorithm has been programmed, then after a triple switching it is required to enter the first register of the code (by turning the ignition circuits on and off). The number of turns corresponds to the previously programmed figure. Then, using a similar procedure, the second register is entered (4 seconds are allotted for each setting step). After confirming the input (single flash of the lamps), the remote control codes are entered into the alarm memory.

A common malfunction of the Scher-Khan Magicar V 5 is a breakdown of the control panel caused by wear on the button mechanisms or moisture on the electronic components. To restore functionality, you need to disassemble the device, and then remove traces of oxidation and replace worn components. If repair is not possible, a new communicator must be purchased, which is then registered in the central unit.

If the alarm does not arm, it is recommended to check the settings. When turned on remote mode Valet happening automatic shutdown security (only locks work). The cause of the malfunction is the breakdown of sensors or limit switches, as well as damage or breakage of the connecting harnesses. The check is performed by a test device, for a detailed analysis of the causes of failure, it is recommended to contact the service center.

Press and hold for 2 sec. key fob button III, after which the trunk will open. If the system is armed (doors locked), it will disarm, the doors will unlock, and the starter will be disabled. To implement this function, it is necessary to have a trunk lock solenoid connected to the corresponding output of the main unit of the car alarm system.

When opening the trunk:

Checking System Status [Button (IV)]

If you need to check the status of the system, briefly press the button IV of the keyfob-communicator. Information about the state of the system will be shown on the keyfob-communicator display, as well as confirmed by siren and alarm signals.

When checking the status of the SCHER - KHAN V car alarm system:

When checking the status of the car security system, the current time indicator shows the temperature value in the car interior. The temperature can be displayed in either °F or °C.

The temperature inside the car is 10°C.

Repeated short pressing of the button IV of the keyfob-communicator within 6 seconds after the first one allows you to view information about the car battery voltage in volts.

The voltage on the car battery is 13.9V.

Panic Mode or JackStop™ (anti-grab) [Button (IV)-]

When you press the button IV of the key fob for 2 seconds. The car alarm system will enter Panic or JackStop ™ (anti-trap) mode - programmable function 1-4 .. If the system has been disarmed, it will arm, the door locks will be locked. The siren will sound for 90 seconds, the alarm will flash for 90 seconds. The "Panic" mode stops the automatic engine start mode. After 90 sec. the car security system SCHER - KHAN V will switch to the armed mode until it is disarmed by the key fob or emergency shutdown mode. Panic mode can be stopped with a short press of the I button. Panic and JackStop™ modes are used in case of danger or when it is necessary to draw attention to the vehicle.

When activating Panic and JackStop™ modes:

Differences in the "Panic" and JackStop ™ algorithms (depending on the selected value of the programmable function 1-4):

ATTENTION!

Jack Stop Mode™ can only be used in an emergency. It is not a regular constantly used STSTS mode, because. it provides for stopping the engine while driving. When choosing one or another mode of the SCHER - KHAN V car alarm, consult with a specialist.

Siren Silence [Button (1+11)]

By briefly simultaneously pressing the buttons I + II of the key fob, you can turn on or turn off the siren signals. In this case, the key fob signals and alarm signals will work as usual. The presence of the symbol serves as an indication of the inclusion of the siren. on the key fob display.

When the siren is turned on:

When turning off the siren signals:

VALET mode [Button (I+III)]

To disable security functions car alarm system SCHER - KHAN 5 and when transferring the car to a service station for maintenance, you can use the VALET mode. To do this, briefly press the buttons I + III of the key fob.

In VALET mode, you can control the locking and unlocking of the door locks. To lock or unlock the locks, briefly press button I.

The VALET mode is shown on the display with the symbol

To exit VALET mode, briefly press the buttons I + III of the key fob

When VALET mode is enabled:

When turning off VALET mode:

Disabling the two-level shock sensor [Button (I+III)]

You can turn off the two-level shock sensor of the SCHER - KHAN 5 car security system. Press and hold for 2 seconds at the same time. buttons 1+ III of the key fob, as a result, the sensors will be turned on or off. The indication of the sensor disconnection is the symbol on the key fob display. Switching off the sensor is necessary if you leave the car where false alarms are possible (the car is parked near tram tracks, a child or an animal remains in the car).

When the shock sensor is disabled:

When you turn on the shock sensor car alarm SCHER - KHAN 5:

The shock sensor is called two-level, because it has two levels of response from the impact on the car.

In case of a weak impact, the car security system warns with 4 short siren sounds and 4 alarm flashes. Key fob - communicator gives a short tone signal, the symbol of impact on the car flashes on the display. If the impact is strong, the system goes into alarm mode for 30 seconds.

Central locking control for turning the ignition on and off [Button (I + IV)]

By briefly simultaneously pressing the buttons I + IV of the key fob, you can turn on or off automatic control central locking (CL) for turning the ignition on and off. If the function is enabled, the door locks will be automatically locked after 30 seconds. after the engine is started and all doors, the hood/trunk will be closed. The locks are unlocked immediately when the ignition is switched off. The function activation is indicated by the presence of a symbol on the key fob display.

When the central locking control function from ignition is turned on:

When the central locking control function is turned off from the ignition:

Passive arming [Button (II+III)]

The passive arming function can be turned on/off by briefly pressing the buttons II+III of the key fob. When passive arming is enabled, the car security system will automatically arm itself after 30 seconds. after closing the last door or after disarming with the key fob. The system warns of passive arming with alarms and (or) siren every 10 seconds. If within 30 sec. doors (hood/trunk) were opened, the system will arm itself in 30 seconds. after closing the doors (hood/trunk).

When passive arming is enabled:

When turning off passive arming:

Setting the timer to automatically start the car engine [Button (II + IV)]

Briefly press buttons II + IV of the key fob to turn the engine start on or off by timer. The presence of the label "TIMER" serves as an indication of the inclusion of starting the engine by timer; on the key fob display. The system provides two modes of starting the engine by timer. The first mode allows you to start the engine every day at a predetermined time, the second mode allows you to start the engine periodically, every 2 hours to warm up (or cool the interior in countries with a hot climate). Two modes cannot be used at the same time, the mode you need can be selected by programmable function 2-3.

To automatically start the engine by timer at the right time (24 hours), it is necessary to make a reservation for this mode. For this:

1. Press the buttons II + IV and turn off the label - TIMER

2. Select start time (table)

3. Press the buttons II + IV and turn off the label - TIMER

In order to enable or disable the engine start by timer every 2 hours, briefly press the buttons II + IV of the car alarm key fob. Setting the start time in this mode is not required, the first engine start will occur 2 hours after the mode is turned on.

When the timer engine start is enabled:

When turning off the engine start by timer:

Note: Automatic engine start timer every 24 hours is useful for starting the engine daily at certain time if your car is parked outside the range of the car alarm key fob.

ATTENTION!

The start time of the car engine according to the 24 hour timer can be shifted up to ± 2 minutes per day.

TURBO mode [Button (II + IV)]

If the car has a Turbo - engine, then after long work at high speeds it is not recommended to stop it immediately. The engine should idle for some time to cool the turbine. To do this, the SCHER - KHAN MAGICAR V system provides a TURBO mode (turbo timer). If the TURBO mode is on, then at the end of the trip the engine will run for 2 minutes. To enable or disable the TURBO mode, briefly press the buttons III + IV of the key fob.

When TURBO mode is enabled:

When turning off the TURBO mode:

To activate the mode at the end of the trip, do the following:

1. Put the gear lever in neutral or "P" position.

2. Turn the key in the ignition lock from the ON position to the OFF position. The car engine will continue to run after this for another 2 minutes.

3. Get out of the car, close the doors. As soon as the doors are closed, the alarm will flash.

Now you can put the car alarm system into car security mode. The engine will then run until the expiration of 2 minutes. interval. When the car is armed, the door, hood/trunk sensors, the driver call sensor are immediately armed, and the shock sensor will start working after the engine stops. The engine will be immediately stopped when the door, hood/trunk sensor is triggered, and the system will go into alarm mode. If necessary, you can urgently stop the engine by pressing for 2 seconds. key fob button II.

Sherkhan 5 is the possibility of remote security control using a key fob. The car alarm consists of two components - the switch itself with an LCD display and the processor unit built into the car.

[ Hide ]

Description and characteristics

Processing unit connects directly to the car battery and runs on 12 volts. Its main function is driving, receiving and transmitting information from sensors.

The key fob switch is used to control the system by the user. In particular, setting the PIN code, programming functions, as well as turning on and off the car's protection.

The equipment is supplied with an additional key fob and detailed instructions. At the same time, there is a manual for both operation and installation of the system. However, not recommended self-assembly systems. It is better to ask to put it to the car service masters.

Main functions

Key fob-switch is designed for direct impact on the system by the user. It is equipped with four control buttons and a display that displays all the necessary current information.

With it, you can turn the system on and off, as well as program the main unit. The power source is only one AAA battery.

The choice of a particular command is displayed on the screen, and is also accompanied by sound and vibration. The display is backlit automatically when the buttons are pressed, as well as during an alarm.

The functionality of the electronic key fob also includes:

• MAGIC CODE - protection against interception of encoded data;
• display of the current battery level;
• displaying the voltage level of the car battery;
• the possibility of remote engine start, including delayed.

You can also check the temperature in the cabin at this moment and see the current time.

The key fob has a special signal reception range and is able to function at a distance of up to one and a half meters from the car. The processor unit is directly responsible for the protection of the transport and the reaction to pressing the key fob buttons.

Its main functions are:

• automatic engine start on command;
• indication of the delay time for turning on accessories;
• disabling car protection by PIN-code in the absence of a key fob;
• obtaining access to the salon by PIN2;
• control of the car's central lock and trunk lock;
• alarm management;
• the ability to protect the car with the engine running.
• The settings allow you to start the engine in the following ways:
• with a frequency of two, four or eight hours;
• every day at a certain time;
• by analyzing the performance of the car - temperature or voltage.

Another available function is programming the maximum and minimum starter rotation times, as well as setting it to increase with an increase in the number of start attempts.

PIN codes are set by the user and are used for emergency access to the vehicle.

Technical specifications

This system can be built into any car, regardless of the type of engine and gearbox. It is possible to start engines equipped with a turbine.

Alerts are divided into three types:

• sound to the siren - lasts for thirty seconds, sounds continuously;
• optical - power one hertz, also lasts thirty seconds, works on two channels, is emitted intermittently;
• through a radio channel - a range of up to one and a half meters, lasts one hundred milliseconds at a frequency of 0.35 hertz, sounds intermittent.

The exact range of the Switch depends on a number of factors, including obstacles, interference, certain weather conditions, and battery level.

The system is managed in one of the following ways:

• remotely using a key fob;
• from the ignition key;
• by triggering the driver call sensor;
• as a response to certain sensor signals.

Electrical circuits are protected by fuses, resistors, and transistors. Additionally equipped with varistors that protect against power surges and interference. The functioning of the system even when the polarity of the power sources is reversed is ensured by diodes.

There are contact sensors that react to opening doors or turning the ignition switch. In this case, the system generates an alarm signal without the possibility of disabling it.

The system also responds to shocks by issuing a signal lasting up to 30 seconds in one cycle. All keyfob radio transmissions occur over a secure channel using special encoding.

The processor unit is characterized by the following parameters:

• work at a voltage of 9 to 18 volts;
• current strength from 20 to 35 milliamps is allowed;
• operates at temperatures ranging from -40 to +85 degrees Celsius;
• the total weight of the device is 270 grams;
• dimensions 150x120x32 mm.

User guide

The system can be configured through the unit or from the key fob. The first is controlled with the help of strokes, and the second - with the buttons. The functionality of the key fob is very wide.

With it, you can:

• set automatic arming;
• stop the alarm mode;
• block the ignition or starter;
• activate the "Free hands" option;
• remotely turn on and off the engine;
• activate the "Panic" mode;
• open trunk;
• connection of the "Turbo" mode;
• program the PIN1 code.

The system block allows you to apply and change PIN2, as well as activate a call to the owner of the car.

PIN code programming

Setting your own PIN1 code takes a few minutes and is not a complicated procedure.

To switch to the programming mode, you need to perform a number of actions:

1. Disable security first.
2. Then open the car door.
3. Turn on the ignition, but do not turn on the engine.
4. Then make a long (about 2 seconds) joint pressing of buttons 3 and 4 on the remote control.

The system will respond with a single beep and flash. However, if you receive a triple beep in response, it means that you have not entered programming mode. Check if you did everything right. It is important that the security mode is disabled, and the ignition, on the contrary, is turned on.

The first digit of the PIN code is given four seconds after the beep. This is done by pressing the key fob button. Its number is equal to the selected number. The selection is confirmed by the appropriate number of beeps and flashes.

The remaining four digits of the code are entered in the same way. They also need to be specified within four seconds. Entering the latter automatically ends the programming mode. This will be indicated by the double sound of the siren and two flashes of the alarm.

After completing the input, you can turn off the ignition and close the car doors.

The PIN2 code is set in the same way:

1. To do this, you need to remove the security mode, open the door and turn on the ignition.
2. Then you need to hit ten times on the call sensor with an interval between hits of less than one and a half seconds. For each hit, the LED will respond with a red indication.

The activation of the programming mode will be accompanied by a fast flashing of the blue LED. Each digit is programmed by strokes. Their number corresponds to the number. One and a half seconds after the input, the input is confirmed. The unit emits the corresponding number of blue flashes, after which it returns to flashing mode.

Enter the rest of the code in the same way. Confirmation of data entry and exit from the programming mode will be accompanied by a single siren sound and a single alarm flash.

Arming

In order to enable the security mode, you must turn off the car ignition and close all doors. After that, a single short press of button 1 on the key fob is performed. Thus, the mode is connected, the starter is blocked and all doors are locked.

Activation of the mode is accompanied by the following indication:

• single siren sound;
• single flashing of the alarm;
• blinking of the indicator with an interval of one second;
• car headlights flashing five times and the closed lock icon on the key fob;
• single switch signal.

The closed padlock icon then lights up and remains displayed until the vehicle is unlocked. From this point on, the system continuously analyzes and monitors the sensor readings. Thirty seconds later, the shock sensor is activated.

If the engine remains on, the installation process guard mode somewhat different. As in the previous case, it is necessary to close all doors and press button 1 on the switch once.

The mode activation indication is similar to the previous case. In this case, the shock sensor will be disabled until the vehicle ignition is turned off. Thirty seconds after the engines stop, the analysis of such signals is turned on.

Button 2 on the key fob is used to disable the security mode.

Keychain - communicator

Before you can start using the key fob, you need to set it up. The first step is to install the power supply.

The symbols on the display show the following information:

• transmitter signal strength;
• battery level;
• clock indicator, as well as the voltage level and temperature in the car;
• state of the lock (open/closed) and security mode;
• disable the shock sensor;
• turning on the vibration signal;
• information about the running timer;
• TURBO mode (enabled/disabled);
• state of the VALET mode;
• display of an open trunk and / or car doors;
• signaling siren;
• inclusion of dimensions;
• visual display of the alarm.

There are also some other symbols representing certain processes.

System check

By pressing the fourth button, you can check the status of the system. The information will be shown on the display.

Cabin temperature Battery voltage

Also, the information is confirmed by a siren and alarm.

Table of signals when checking the status of the vehicle system

Autostart security system

It is possible to automatically turn on the car security system. It can be programmed with a key fob.

In this case, the system will be armed 30 seconds after all doors are locked. At the same time, an appropriate indication and a siren are issued. For another thirty seconds, you can still open the trunk or car doors. If this is done, the auto-on countdown is delayed by another half minute.

If this function is enabled, the PASSIVE indicator will be displayed on the keyfob display.

Auto engine start

The system assumes automatic start of the engine. This is essential in order to maintain certain parameters car, as well as warming up when it is in the parking lot.

Automatic start can be controlled by both sensors and set user timer.

Auto start by battery temperature and voltage

Automatic start of the engine on the machine can occur on a timer or based on the readings of temperature and voltage sensors.

Thus, the number of timer starts is controlled depending on the temperature in the cabin or the voltage level of the car battery. This is configured with a key fob.

The temperature threshold can take one of the following values: -15, -25, +60 degrees Celsius. Restriction according to the voltage level can take only one value - 11.5 volts. Thus, it is possible to adjust the activation of the timer depending on the current parameters of the sensors. This allows you to regulate the temperature of the passenger compartment, as well as maintain the operating voltage in the battery.

Autostart by timer

It is necessary to set the remote autostart of the system by timer in this way: simultaneously press buttons 2 and 4. It is also with their help that the start time is set.

When the timer is turned on, the TIMER indicator on the display lights up, and the engine is controlled according to the time specified by the user.

There are four different engine start modes according to the pre-set timer:

• daily at the specified time;
• periodically, every eight hours;
• every four hours;
• every two hours.

Periodic activation is used to control the temperature in the cabin (heating or cooling the space).

It is possible to install only one mode, it is not supposed to combine them. Setting another behavior automatically disables the previous one.

Turning the engine start on and off according to the timer is accompanied by sound signals and light indication. The display flashes five times.

The exact time of automatic start needs to be specified only for daily switching. In all other modes, the report starts from the moment the function is enabled.

Why the autostart of the Scher-Khan Magicar 5 alarm may not work

If the Sherkhan Magikar 5 autostart system cannot start the engine remotely, the key fob will emit three short beeps. Accordingly, there will be three flashes of the alarm, and after three seconds a series of flashes will occur. This series displays which error has occurred.

Therefore, depending on the number of flashes, you can determine why the engine does not start:

1. If there is one flash, it means that the engine is already on.
2. If two, the ignition is on.
3. If three - opening one of the doors prevents starting.
4. If four - a similar situation, but with a trunk or hood.
5. In the event that the system responded to you with five flashes, the start reservation for the car in manual transmission has not been made.

If the remote engine start does not work, the system will try to start it again. In the event that this fails to be done three times in a row, the alarm will go into standby mode. If this happens, the car will no longer start, you must contact the service center to determine the cause of the problem.

Video "Autostart stopped working"

What to do if the car does not start from autorun is described in the video from Seryoga.