The system can remember the codes of three key fobs. To program new key fobs, follow two steps.
1. Turn the ignition key three times from OFF to ON.
The alarm will flash once to confirm entry into programming mode.
2. No later than 4 sec. after the alarm flashes, press button I of the key fob, the code of which must be entered into the memory of the processor unit.
If no action is taken after step 1, then after 4 seconds. alarm flashes 2 times, the system will switch from the keyfob programming mode to the VALET mode.
Note: the system has three memory cells for storing key fob codes. When you try to write the fourth key fob, the code of the first recorded key fob will be deleted.
Sher-Khan 7.8
PROGRAMMING KEYFOBS
The system can remember the codes of three key fobs.
To write keyfob codes:
1) In the "disarmed" mode with the ignition on, press the button on the call sensor housing for 2 seconds. The alarm will flash once
2) Within 5 sec. briefly press the call sensor button. The alarm will flash twice if personal PIN 1 is not used (programmable function 1-6 in the factory
value, see page 69) or once if PIN 1 is used (programmable function 1-6 in optional value)
3) If PIN 1 is used, then it is necessary to enter its value (“Entering a personal PIN 1 code in key fob programming mode”, steps 5 to 8 on page 60). The alarm will flash twice
4) After 5 sec. the LED will turn blue, confirming the readiness to enter key fob codes
5) Within 5 sec. briefly press button I of the first key fob. The alarm will flash 1 time to confirm that the code has been written. Then you can enter the code of the second and third keyfobs, after the successful entry of the code of each new keyfob, the alarm will flash 1 time, after entering the code of the third keyfob, the alarm will flash twice and the system will exit the keyfob programming mode.
When writing the code of at least one new keyfob, the codes of all keyfobs previously recorded in the system memory will be deleted
To exit the programming mode, do not take any action for 4 seconds. after writing the code of the last key fob.
If no action is taken after step 4, then after 5 seconds. You will hear one siren sound*, the alarm will flash once, the system will switch from key fob programming mode to VALET mode.
Sher-Khan Jungle, Vegas
PROGRAMMING NEW KEYFOBS
The system can remember the codes of four key fobs.
To start programming new key fobs, you must:
Disarm the system
Turn on car ignition
In the case when the PIN code is not used (factory value of the programmable function is 20), the following sequence of actions must be performed:
1) Within 5 seconds, short press three times VALET button. The system will confirm the action taken with one flash of the alarm.
2) Within the next 5 seconds, briefly press the button of the first key fob. The system will confirm the successful entry of the key fob code with one flash of the alarm. The code of the new key fob will be added to the memory of the processor unit. This will delete the key fob code that was programmed first.
3) In the case when it is necessary to program the codes of several key fobs, it is necessary to sequentially press the button on each of them with a time interval between pressings of at least 1 second and no more than 5 seconds. The system will acknowledge each press with one alarm flash.
If no action is taken within 5 seconds, the system will automatically end the programming mode of new key fobs, which will be confirmed by two alarm flashes
4) If four key fobs are being programmed, then after pressing the button on the last of them, the system will automatically end the programming mode of new key fobs, which will be confirmed by two alarm flashes. In the event that less than four key fobs are being programmed and it is necessary to delete the codes of the previous key fobs from the memory, press the button on any of the key fobs several times until the system exits the programming mode (two alarm flashes)
In the case where a PIN code is used (value 2 of programmable function 20), to program new
key fobs, you must perform the following sequence of actions:
1) Entering the first digit of the PIN code (factory setting is “1”). To do this, briefly press the VALET button in succession required number times corresponding to the first digit of the PIN. The time interval between pressing should be no more than 3 seconds. After that, do nothing for 3 seconds. After this time, the system will confirm the entry of the first digit with one flash of the alarm.
2) Entering the second digit of the PIN code (factory setting - "1"). To do this, briefly press the VALET button in a row the required number of times, corresponding to the second digit of the PIN code. To enter the PIN code correctly, you must start entering the second digit no later than 3 seconds after the alarm flashes, confirming the entry of the first digit. The time interval between presses should also be no more than
3 seconds. After entering the second digit, do nothing for 3 seconds. After this time has elapsed, the system will confirm that the correct PIN values have been entered with one flash of the alarm. If two alarm flashes follow, this means that the PIN code was entered incorrectly, and the system returns to its original mode and it is impossible to update the key fob codes.
After three unsuccessful attempts to enter the PIN code this operation blocked for 30 minutes
3) Within 5 seconds after confirmation correct input PIN code, short press the button of the first key fob. The system will confirm the successful entry of the key fob code with one flash of the alarm. The code of the new key fob will be added to the memory of the processor unit. This will delete the key fob code that was programmed first.
4) When it is necessary to program the codes of several key fobs, it is necessary to sequentially press the button on each of them with a time interval between pressings of at least 1 second and no more than 5 seconds. The system will acknowledge each press with one alarm flash. If no action is taken within 5 seconds, the system will automatically end the programming mode of new key fobs, which will be confirmed by two alarm flashes
5) If four key fobs are being programmed, after pressing the button on the last one, the system will automatically end the programming mode of new key fobs, which will be confirmed by two alarm flashes. In the event that less than four key fobs are being programmed and it is necessary to delete the codes of the previous key fobs from the memory, press the button on any of the key fobs several times until the system exits the programming mode (two alarm flashes)
Sher Khan 6
PROGRAMMING TECHNIQUE FOR NEW KEYFOBS
ATTENTION!
The system has a secure algorithm for recording new key fobs,which excludes unauthorized entry of key fobs into memorysystems. To ensure the privacy of the entry, do not forget to enter the codeemergency stop PIN 1.
The system can remember the codes of three key fobs. To start programming, the system must be disarmed using a key fob or emergency using the PIN1 ignition switch or using the PIN2 call sensor. Also on the key fob to be recorded, the function " Free hands».
To program new key fobs, follow four steps:
1. Turn the ignition key three times from the OFF position to the ON position. The alarm will flash once to confirm that the first step has been completed. Switch off the ignition.
2. Not later than 4 sec. after flashing the alarm, turn on the ignition the number of times corresponding to the first digit of the personal code (factory setting "1"). Switch off the ignition. The alarm will flash once to confirm that the second digit is ready to be entered.
3. Not later than 4 sec. after flashing the alarm, turn on the ignition the number of times corresponding to the second digit of the personal code (factory value "1"). Switch off the ignition.
The alarm will flash once to confirm that the third digit is ready to be entered.
4. Not later than 4 sec. after the alarm flashes, press button I of the key fob, the code of which must be entered into the memory of the processor unit. With an interval of no more than 4 seconds, you can press buttons 1 of three key fobs, then the system will remember their codes. If you need to write down the code of only one key fob, then briefly press the button I of this key fob three times.
To exit the programming mode, do not take any action within 4 seconds. after writing the code of the last key fob.
Two alarm flashes will follow, confirming the exit from the key fob code programming mode.
Note:
The system has three memory cells for storing key fob codes. When trying to record the fourth key fob, the code of the first recorded key fob
Scher Khan security systems have a long range of two-way communication. Autorun Sherkhan 5 can be performed according to several settings, depending on the desire of the owner.
[ Hide ]
Main characteristics
Deactivation of the signaling from the key fob
The system can operate in a passive mode, when the protection is activated half a minute after closing all doors and covers on the body. If the doors do not open when the system is turned off, it will automatically arm. To use the passive mode, it should be activated by briefly pressing the second and third buttons of the main key fob.
Passive operation mode is active (the Passive icon is lit on the display)
If the doors and the trunk lid were opened and closed, the system will turn on protection half a minute after the lock of the last element is clicked into place.
Keychain - communicator
The main key fob supplied in the kit has the following functional features:
- thanks to the four-button scheme, it is possible to control all system functions;
- the signal from the key fob is encoded according to a special Magic Code scheme, which prevents interception and recording;
- the built-in display with illumination provides visual display of all operations;
- when working with the system, the key fob confirms commands with a sound or vibration signal;
- additional information from sensors can be displayed on the screen;
- the key fob is the main tool for programming automatic start;
- using the key fob, the system parameters are configured.
After unpacking and installing the system on the car, it is necessary to bring the main key fob into working condition. To do this, you will need to remove the dielectric gasket installed between the contact pads of the battery and the key fob power circuit.
Action algorithm:
- Open the battery cover. To do this, open the latch and slide the cover to the bottom of the key fob.
- Remove the battery from the compartment.
- Remove the gasket located along the entire length of the element.
- Return the battery to the local location, observing the installation polarity indicated on the sticker. If there is no marking, remember that the negative pole of the battery is always directed towards the antenna of the Sherkhan Magikar key fob.
- Close the lid and lock the latch.
Pictograms on the keychain Sherkhan Magikar 5
The following symbols and icons may appear on the screen:
- timer start (A);
- turbo timer mode (B);
- passive activation of the system (C);
- automatic activation mode without pressing the buttons (D);
- included siren (E);
- shock detection sensor (F) is off;
- vibrating alert is active in the key fob (G);
- control of door locks after starting the ignition (H);
- open trunk lid (J);
- the engine is switched on in the autostart mode (K);
- system state (L);
- open doors (M);
- field for displaying hours, temperature and data during autorun (N);
- operating mode Valet (O);
- working alarm or dimensions not switched off (P);
- shock sensor triggering (Q);
- key fob battery indicator (R);
- signal level (S).
Marat Askarov demonstrates setting the clock in the Magicar 5 key fob.
Autostart security system
Under the autostart of the system, they mean turning on and off the protection without pressing the buttons on the key fob. The mode is called “hands free” and is activated by pressing button one on the main key fob for two seconds. The system automatically turns on or off at a distance of up to 35 meters from the vehicle. When operating the alarm in conditions of strong interference, this distance can be reduced to 15 meters.
The black oval highlights the hands-free mode icon
The hands-free mode can only be controlled using the main key fob with a display.
Auto engine start
When using automatic start, you need to remember and follow a few rules:
- Using autorun is allowed only when the machine is placed in a ventilated area and subject to visual contact.
- Produce automatic start prohibited when people are standing in front or behind the vehicle.
- The parked car must be fixed with a working parking brake.
- Before enabling the autorun feature on machines with manual method shifting speeds, it is necessary to set the "software neutral".
- Monitor coolant or oil levels.
- Set in advance on the microclimate control unit the direction of airflow and the desired air temperature in the cabin.
- Do not pass the key fob to play with children.
Before turning on the engine start system on vehicles with a manual gearbox, the neutral position of the gearbox lever must be programmed. There are three options for this, the description of the steps for each of them is given below. The mode can be programmed through the system settings menu.
The first option provides:
- Stop in a parking space, apply the parking brake, move the gearshift lever to neutral and remove the key from the lock cylinder.
- With the engine still running, open the door, leave the vehicle and slam it behind you. The motor must stop.
If you need to pick up things from the trunk, then you should use the second option:
- After setting the lever to the neutral position and turning off the ignition, the driver exits the car and does not close the door behind him.
- Open the trunk and take out everything you need.
- Close the door and then slam the luggage compartment lid. The engine will stop and be ready for automatic start.
The third option looks like this:
- Set the neutral position and apply the parking brake.
- Close doors.
- Press button two on the key fob for two seconds.
- Turn off the ignition and get out of the car.
- Close the door, after which the motor will stop.
When installing autorun on the machine, the neutral setting procedure is not required, just put the box selector in the parking mode.
To provide remote engine start, it is necessary to install a device to bypass the immobilizer.
The engine can be started by pressing the second key fob button. After starting the engine, the display will show the remaining operating time. This parameter is programmable and can be 45/25/15 or 5 minutes. If necessary, the car door can be opened by pressing the first button and within 20 seconds, insert the key into the lock and turn to the active ignition position.
Display in engine mode
Autostart by timer
To connect and disconnect the function, a short press on the buttons three and four is used, after which the icon with the inscription Timer will turn on on the screen.
There are two options for working, which are configured programmatically:
- daily run, repeating every 24 hours;
- auto-restart every 2/4/8 hours.
To enable daily start, a so-called redundant mode must be carried out.
For this you need:
- Turn off the timer mode by briefly pressing buttons two and four.
- To enter the setting, press buttons one and two for a few seconds.
- Turn on the mode by pressing 13 times on the button four. Each press will be accompanied by a signal.
- Select the repeat time by pressing the buttons (the second button gives a repeat of 8 hours, the third - 4 hours and the fourth - two hours).
- Enable timer.
Enable timer start
Auto start by battery temperature and voltage
The engine is switched on according to the temperature inside the cabin minus 15 or 25 degrees in winter time and plus 60 in the summer.
- Turn off the timer start mode.
- Press button four 21 times.
- Use the buttons to select the switching threshold (the fourth - plus 60, the third - minus 25 and the second - minus 15).
- Enable timer.
When setting the voltage in the on-board network, the system will operate at a value of 11.5 V.
- Press 20 times on the fourth button.
- Turn on voltage start with button two.
In all warm-up modes, you can vary the operating time of the power unit.
For this, the steps are:
- Press button number four twelve times.
- Select the operating time using the buttons from the first to the fourth, choosing each time from the range of 5-15-25-45 minutes.
Scher-Khan Magicar 5 alarm auto start malfunctions
The main causes of malfunctions that are possible when auto-starting the Sher-Khan Magikar 5 alarm:
- The engine does not start even though automatic start backup is running normally. The cause may be oxidized fuse legs in the power supply circuit of the main unit. Another reason may be the failure of the standard immobilizer crawler or the sticking of the contacts in the control relay.
- The motor starts and then stalls after a few seconds of operation. At the same time, in normal mode, the engine starts without problems from the ignition switch. One of probable causes there may be damage inside the five-pin relay installed in the main unit.
- A common reason why the start does not work is incorrect parameter settings. To eliminate this, you must return the system to factory settings and re-program.
- Sometimes the reason that the automatic start stopped working may be the inclusion of Valet mode. This mode is characterized by a permanently lit control diode. After the setting mode is turned off, the start returns to normal.
Car Alarm Sherkhan 5 User Manual
MAGICAR V
User's manual
PURPOSE
The Sherkhan 5 system is a car alarm with the ability to control via radio using a key fob-communicator with a liquid crystal display. The system exchanges information between the key fob-communicator and the processor unit at a distance of up to 1500 m. Sherkhan 5 has a function for automatically starting the engine by commands from the key fob or by commands from the internal timer. The system is designed to work on gasoline or diesel vehicles with a fuel injection system and an on-board network voltage of 12V. The protection of the processor unit, shock sensor, call sensor, antenna unit is made according to the IP-40 standard and provides for installation in the car. The siren is IP-65 rated and can be installed in the engine bay away from the exhaust manifold and high voltage systems.
Keyfob communicator functions
- Multifunctional, 4-button LCD keychain communicator
- Protection against interception of MAGIC CODE code packets
- Audiovisual confirmation of executed commands
- Vibrating bell
- Loud beeps
- Ultra long distance communication up to 1500 m with processor unit
- Automatic display backlight
- Low battery indication
- Voltage indication battery car
- Indication of temperature in the passenger compartment
- Current time display
- Indication of engine operating time in automatic mode
- Remote engine start
- Programming the engine start time (accurate to the minute)
- Sound and visual alert reminder mode
- Operational, from the key fob, programming of all system functions
- Economy Power (one AAA element)
Processing unit functions
- Automatic engine start for vehicles with automatic or manual transmission
- Operation of the starting system with both petrol and diesel engines
- Operation of the starting system with engines having a turbine
- Starting the engine on command from the key fob
- Automatic engine start every 2 hours
- Automatic engine start at a pre-set time every 24 hours
- Monitoring the engine start by signals from the generator or by noise in the on-board network
- Personal code for access to the car interior if the key is lost
- Power output for controlling the car's central locking
- Trunk release power output
- Alarm control power output (two circuits)
- Programming the lock relay type
- Auto arming (programmable function)
- Sound warning before automatic arming
- Automatic return to armed mode if the door was not opened
- Sound warning before automatic return to armed mode
- Armed mode without siren signals
- Two universal programmable control channels for additional devices
- Ability to connect negative and positive door sensors
- Input for negative trunk sensor
- Locking and unlocking the door locks when starting and stopping the engine
- Possibility of arming with and without confirmation siren signals
- Alarm warning about open door(programmable function)
- Panic or JackStop mode
- Highly sensitive two-level shock sensor with sensitivity adjustment
- "Hands free" function for automatic arming / disarming when the owner moves away / approaches the car
- Dual mode hands-free function
- Parking lights not switched off warning
TECHNICAL PARAMETERS Sherkhan 5
Alarm types:
Influence on the main and additional electrical equipment of the car
| STSTS controls the power supply to: | Maximum current per channel |
|---|---|
| Starter or ignition interlock circuit | Imax = 0.2 A |
| Port Alarm Circuit | Imax = 10 A |
| Starboard Alarm Circuit | Imax = 10 A |
| Ignition circuit | Current Imax = 30 A |
| Accessory chain | Current Imax = 30 A |
| Starter circuit | Current Imax = 30 A |
| Ignition circuit 2 | Current Imax = 0.2 A |
| Additional siren | Current Imax = 2 A |
| Relay for unlocking electric door locks or unlocking the standard system of the Central locking (CL) of the car | Current Imax = up to 15 A |
| Relay for controlling the locking of electric door locks or locking the standard system of the Central lock (CL) of the car | Current Imax = up to 15 A |
| Power trunk lock relay | Current Imax = 10 A |
| Control channel additional device 1 | Current Imax = 0.2 A |
| Option control channel 2 | Current Imax = 0.2 A |
| The channel for disarming the STSTS standardly installed on the car | Current Imax = 0.2 A |
Control methods
- Remotely with a radio frequency transmitter (key fob) at a frequency of 433.92 MHz ± 0.2% with a power of not more than 10 mW
- From the ignition key
- Automatically based on signals from sensors
Electrical circuit protection
Fuses. (Automotive slow-acting fuses according to wiring diagram)
Spheres of protection
Other parameters
Batteries
* The table shows the average value. The service life of the key fob battery depends on the intensity of use of the key fob and the quality of the battery, the key fob operation modes.
ATTENTION!
Use only quality batteries. Battery Application Low quality can lead not only to a reduction in the life of the key fob, but also to its damage.
KEYFOB COMMUNICATOR
Preparing the key fob-communicator for work
Before using the key fob, you must bring it into working condition, because. during transportation and storage, an insulating gasket is installed between the contact of the battery and the contact plate of the key fob, which prevents the battery from discharging before operation. Before using the key fob, remove it. To do this, release the battery compartment cover lock, press the cover and slide it in the direction opposite to the antenna. Remove the battery. Remove the insulating pad between the battery and the collector plate. Install the battery back, observing the polarity indicated on the bottom of the battery compartment. If there is no indication of the polarity of the battery, then it is set with a negative terminal towards the antenna. Close the battery cover. Keyring is ready to go.
Symbols on the keyfob-communicator display
| Timer start indicator | |
| TURBO mode indicator | |
| Passive arming indicator | |
| Hands-free mode indicator | |
| Siren indicator | |
| Shock sensor off indicator | |
| Vibrating alert indicator | |
| Indicator of turning on the automatic control of the central lock by ignition | |
| Door open indicator | |
| Trunk/hood open indicator | |
| Shock sensor alarm indicator (optional sensor) | |
| Car owner call indicator | |
| Engine running indicator | |
| Ignition on indicator in security mode, indicator of side lights not switched off | |
| Key fob transmitter operation indicator | |
| Battery discharge indicator of the key fob-communicator | |
| VALET mode indicator | |
| Locking and unlocking indicator. Security Mode Status Indicator | |
 |
Clock indicator, car battery voltage, interior temperature, engine warm-up time during automatic start |
Purpose of the buttons of the key fob-communicator Sherkhan 5
Example notation:
I - quick (0.5 sec.) button press
I- - long (2 sec.) button press
(I + II) - fast (0.5 sec.) simultaneous pressing of the buttons (combination of buttons)
(I + II) - - long (2 sec.) simultaneous pressing of the buttons (combination of buttons)
| Control channel number | Button number | Press duration | Executed function (mode) |
|---|---|---|---|
| 1 | I | 0.5 sec. |
|
| 2 | I-(1) | 2 sec. | Activate "Hands Free" function first operating mode (symbol does not flash) |
| 3 | I-(2) | 2 sec. | Activate the "Hands free" function of the second operating mode (the symbol flashes) |
| 4 | I-(3) | 2 sec. | Deactivate hands-free function (symbol is off) |
| 5 | (III+IV) - | 2 sec. | Recording and playback of a fragment on the voice module (Option) |
| 6 | II | 0.5 sec. | Additional channel control 1 |
| 7 | III | 0.5 sec. | Additional channel control 2 |
| 8 | IV | 0.5 sec. | Checking System Status |
| 9 | II- | 2 sec. | Starting and stopping the engine from the key fob |
| 10 | III- | 2 sec. | open trunk |
| 11 | IV- | 2 sec. | "Panic". To stop, press the I button |
| 12 | (I+II) | 0.5 sec. | Siren on/off |
| 13 | (I+III) | 0.5 sec. | "Valet" mode enable/disable |
| 14 | (I+IV) | 0.5 sec. | Automatic control of the central lock by ignition on / off |
| 15 | (II+III) | 0.5 sec. | Automatic arming enable/disable |
| 16 | (II+IV) | 0.5 sec. | Timer start enable/disable |
| 17 | (III+IV) | 0.5 sec. | Turbo mode enable/disable |
| 18 | (I+III)- | 2 sec. | Shock sensor enable/disable |
| 19 | (I+II)- | 2 sec. | Enter programming menu 1 |
| 20 | (I+IV)- | 2 sec. | Enter programming menu 2 |
Note: Sherkhan 5
With a long 2 sec. pressing the I button, the modes change sequentially in the order (1) > (2) > (3) > (1) … . In mode (2), the "Hands free -" function has a high range work- symbol blinking.
Setting the time on the keyfob-communicator display
Setting the current time is required before starting the operation of the system or when changing the key fob battery. Follow the steps according to the table below.
| Execution steps | Press duration | Executed function (mode) | |
|---|---|---|---|
| STEP 1 | (II+III)- | 2 sec. | |
| STEP 2 | I | 0.5 sec. | Turn on the current time setting mode. The indications of the current time are flashing, confirmed by a sound signal from the key fob |
| STEP 3 | I | 0.5 sec. | Changing the value of the clock |
| II | 0.5 sec. | Changing the minutes | |
| STEP 4 | (II+III)- | 2 sec. |
ATTENTION!
Setting the correct time is necessary condition for correct operation automatic start of the engine by timer.
Setting the keyfob-communicator, vibration call, owner call, temperature display standard "°F" or "°С"
To set the desired key fob operation mode, follow the steps in accordance with the table below.
Note: STEP 2 must be completed within 15 seconds. after STEP 1.
Arming [Button (I)]
Close doors, hood, trunk. Briefly press button I on the key fob. The system will switch to the armed mode, the door locks will be locked, the starter (ignition) interlock will turn on until the system is disarmed.
When arming:
Enable sensors:
- Immediately after the LED starts flashing, the system begins to monitor the status of the doors, hood, trunk, call sensor of the owner of the car.
- The shock sensor will turn on after 30 seconds. after arming.
Note:
If, when arming, you heard three signals from the key fob, and on the display for 5 seconds. the image of an open door or trunk flashes, this means that the door, hood / trunk is open in the car. The door, hood/trunk sensor will be immediately armed when its functionality is restored.
The hood area is not displayed separately, the hood sensor must be connected to the trunk sensor wire.
Disarming [Button (I)]
When the system is armed, briefly press button I on the key fob. The system will be disarmed, the door locks will be unlocked, the starter (ignition) interlock will be disabled.
When disarming:
HANDS FREE function [Button (I)-]
ATTENTION!
The "Hands free" mode works only when using a keyfob-communicator with a liquid crystal display; when using optional keyfobs without a display, this mode is not available.
When you press button I of the key fob-communicator for 2 sec. You can turn Hands Free on or off. When the "Hands-free" function is enabled, the system will automatically arm itself when you are 15-35 m away from the car with the key fob-communicator*. or is removed from the security mode and unlocks the door locks when approached. The function has two modes of operation:
In the first mode, the mark on the display does not blink and the range of the function is minimal.
In the second mode, the mark on the display with the inscription "AUTO" flashes and the range is maximum.
The change of operating modes takes a long 2 seconds. by pressing the I button next order: (Function on, mode 1) > (Function on, mode 2) > (Function off) > (Function on, mode 1)….
Arming/disarming will be accompanied by a melodic signal from the key fob-communicator.
Continuous use of the "Hands-free" function is not recommended, as its use drastically reduces the battery life of the key fob.
* Note:
The distance from the unit to the key fob-communicator, at which the system makes a decision to arm or disarm, can vary and depends on a group of objective reasons: relative position antennas of the key fob-communicator and the antenna unit, the presence of metal objects near the antennas, from radio interference on the air, weather, etc. ...
When the hands-free function is enabled:
Mode change is accompanied by one signal from the key fob-communicator.
When the HANDS FREE function is turned off:
Starting the engine on command from the key fob [Button (II) -]
To start the engine, press button II on the key fob for 2 seconds. The system will be armed, the door locks will be locked, the car engine will start. After the engine has started, the keyfob-communicator displays information about the time remaining until the end of engine operation in automatic mode. Engine run time is programmable and can be 15/25/45/5 minutes (programmable function 2-4). To start driving. You need to open the door, insert the ignition key into the lock and turn it to the "ON" position. To do this, you have 20 seconds, after this time the system will transfer control to the ignition switch, if you do not turn on the ignition, the engine will be stopped.
If the launch did not occur the first time, the system will try again. The system makes no more than three attempts to start, after which it goes into standby mode. If the car engine does not start after the last attempt, contact a service station to diagnose your car.
At the time of launch:
The system will not start the engine if:
- Ignition on
- The car engine is already running
- Door or hood/trunk open
- Backup mode failed for vehicles with manual transmission
On successful launch:
Note: If the car's engine is started automatically, the current time indicator shows the time remaining until the engine is stopped. Time is displayed in countdown mode. Time display format in this mode: [ XX min: XX sec.]
When the engine stops automatically:
Trunk opening [Button (III)-]
Press and hold for 2 sec. key fob button III, after which the trunk will open. If the system is armed (doors locked), it will disarm, the doors will unlock, and the starter will be disabled. To implement this function, it is necessary to have a trunk lock solenoid connected to the corresponding output of the main unit of the system.
When opening the trunk:
Checking System Status [Button (IV)]
If you need to check the status of the system, briefly press the button IV of the keyfob-communicator. Information about the state of the system will be shown on the keyfob-communicator display, as well as confirmed by siren and alarm signals.
When checking system status:
When checking the status of the Sherkhan 5 system, the current time indicator shows the temperature in the car. The temperature can be displayed in either °F or °C.
The temperature inside the car is 10°C.
Repeated short pressing of the button IV of the keyfob-communicator within 6 seconds after the first one allows you to view information about the car battery voltage in volts.
The voltage on the car battery is 13.9V.
Panic or JackStop mode (anti-seizure) [Button (IV)-]
When you press the button IV of the key fob for 2 seconds. The system will enter Panic mode or Jack Stop mode(protection against capture) - programmable function 1-4.. If the system was disarmed, it will arm itself, the door locks will be locked. The siren will sound for 90 seconds, the alarm will flash for 90 seconds. The "Panic" mode stops the automatic engine start mode. After 90 sec. the system will go into armed mode until it is disarmed by the key fob or emergency shutdown mode. Panic mode can be stopped by briefly pressing button I. Panic and JackStop modes are used in case of danger or when it is necessary to draw attention to the vehicle.
When activating the "Panic" and JackStop modes:
Differences in the "Panic" and JackStop algorithms (depending on the selected value of the programmable function 1-4):
ATTENTION!
JackStop mode should only be used in emergency situations. It is not a regular constantly used CCTTC mode. it provides for stopping the engine while driving.
When choosing one or another mode, consult with a specialist.
Siren Silence [Button (I+II)]
By briefly simultaneously pressing the buttons I + II of the key fob, you can turn on or turn off the siren signals. In this case, the key fob signals and alarm signals will work as usual. The siren activation is indicated by the presence of a symbol on the key fob display.
When the siren is turned on:
When turning off the siren signals:
VALET Mode [Button (I+III)] Sherkhan 5
To disable the security functions of the system and when transferring the machine to a service station for maintenance, you can use the VALET mode. To do this, briefly press the buttons I + III of the key fob.
In VALET mode, you can control the locking and unlocking of the door locks. To lock or unlock the locks, briefly press button I.
The VALET mode is shown on the display with the symbol
To exit the VALET mode, briefly press the buttons I + III of the key fob
When VALET mode is enabled:
When turning off VALET mode:
Disabling the two-level shock sensor [Button (I + III)] Sherkhan 5
You can disable the two-level shock sensor. Simultaneously press and hold for 2 seconds. buttons I + III of the keyfob, as a result, the sensors will be turned on or off. The indication of the sensor disconnection is the symbol on the key fob display. Switching off the sensor is necessary if you leave the car where false alarms are possible (the car is parked near tram tracks, a child or an animal remains in the car).
When the shock sensor is disabled:
When the shock sensor is turned on:
The shock sensor is called two-level, because it has two levels of response from the impact on the car.
In case of a weak impact, the system warns with 4 short siren sounds and 4 alarm flashes. Key fob - communicator gives a short tone signal, the symbol of impact on the car flashes on the display. If the impact is strong, the system goes into alarm mode for 30 seconds.
Central locking control for turning the ignition on and off [Button (I + IV)]
By briefly simultaneously pressing the buttons I + IV of the key fob, you can turn on or off automatic control central locking (CL) for turning the ignition on and off. If the function is enabled, the door locks will be automatically locked after 30 seconds. after the engine is started and all doors, the hood/trunk will be closed. The locks are unlocked immediately when the ignition is switched off. The function activation is indicated by the presence of a symbol on the key fob display.
When the central locking control function from ignition is turned on:
When the central locking control function is turned off from the ignition:
Passive Arming [Button (II+III)] Sherkhan 5
The passive arming function can be turned on/off by briefly pressing the P+S buttons on the key fob. When passive arming is enabled, the system will automatically arm itself after 30 seconds. after closing the last door or after disarming with the key fob. The system warns of passive arming with alarms and (or) siren every 10 seconds. If within 30 sec. doors (hood/trunk) were opened, the system will arm itself in 30 seconds. after closing the doors (hood/trunk).
When passive arming is enabled:
When turning off passive arming:
Setting the timer for automatic engine start [Button (II+IV)]
Briefly press the buttons II + IV of the key fob to turn the engine start on or off by timer. The indication of the inclusion of starting the engine by timer is the presence of the label "TIMER" on the key fob display. The system provides two modes of starting the engine by timer. The first mode allows you to start the engine every day in advance set time, the second mode allows you to start the engine periodically, every 2 hours to warm up (or cool the interior in countries with a hot climate). Two modes cannot be used at the same time, the mode you need can be selected by programmable function 2-3 .
To automatically start the engine on a timer in right time(24h) you need to make a reservation for this mode. For this:
- Select start time (see table)
- Press the buttons II + IV and turn off the label "TIMER"
| Execution steps | Button number or combination of buttons | Press duration | Executed function (mode) |
|---|---|---|---|
| STEP 1 | (II+III)- | 2 sec. | Entering the keyfob function programming mode. The appearance of a symbol is confirmed by a sound signal from the key fob |
| STEP 2 | II | 0.5 sec. | Turn on the timer setting mode. The readings of the previously set time flash, confirmed by the beep of the key fob |
| SHAGZ | I | 0.5 sec. | Changing the value of the clock |
| II | 0.5 sec. | Changing the minutes | |
| STEP 4 | (II+III)- | 2 sec. | Exit from the programming mode of the key fob functions. Confirmed by a beep from the key fob |
In order to enable or disable the engine start by timer every 2 hours, briefly press the buttons II + IV of the key fob. Setting the start time in this mode is not required, the first engine start will occur 2 hours after the mode is turned on.
When the timer engine start is enabled:
When turning off the engine start by timer:
Note: Automatic start of the engine on a timer every 24 hours is useful for starting the engine daily in certain time if your car is parked outside the range of the key fob.
ATTENTION!
The engine start time according to the 24 hour timer can be shifted up to ±2 minutes per day.
TURBO Mode [Button (II+IV)]
If the car has a Turbo - engine, then after long work at high speeds it is not recommended to stop it immediately. The engine should idle for some time to cool the turbine. For this, the SCHER-KHAN MAGICAR V system has a TURBO mode (turbo timer). If the TURBO mode is on, then at the end of the trip the engine will run for 2 minutes. To enable or disable the TURBO mode, briefly press the buttons III + IV of the key fob.
When TURBO mode is enabled:
When turning off the TURBO mode:
To activate the mode at the end of the trip, do the following:
- Put the gear lever in neutral or "P" position.
- Turn the ignition key from the ON position to the OFF position. The engine will continue to run after this for another 2 minutes.
- Get out of the car, close the doors. As soon as the doors are closed, the alarm will flash
Now you can arm the system. The engine will then run until the expiration of 2 minutes. interval. When the car is armed, the door, hood/trunk sensors, the driver call sensor are immediately armed, and the shock sensor will start working after the engine stops. The engine will be immediately stopped when the door, hood/trunk sensor is triggered, and the system will go into alarm mode. If necessary, you can urgently stop the engine by pressing for 2 seconds. key fob button II.
Auxiliary channel 1 control [Button (II)]
If your car is equipped with an electromechanical hood lock, an additional preheater or other service equipment, you can control the operation of these devices using a key fob. To do this, briefly press button II on the key fob. A short or long signal will appear at the output of additional channel 1 of the processor unit (programmable function 2-5). The siren and parking lights signals will differ when controlling an additional channel, depending on the state of the programmable function 2-5. If a channel is programmed for a long tone (Programmable Function Value 4 2-5), the system will confirm its activation and deactivation with siren and alarm signals. If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel. The additional channel does not work in the VALET mode and in the alarm mode.
Turning on an additional channel:
Note: If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel (programmable function 2-5)
Auxiliary channel 2 control [Button (III)]
If your car is equipped with an electromechanical hood lock, an additional preheater or other service equipment, you can control the operation of these devices using a key fob. To do this, briefly press button III on the key fob. A short or long signal will appear at the output of additional channel 2 of the processor unit (programmable function 2-6). The siren and parking lights signals will differ when controlling an additional channel, depending on the state of the programmable function 2-6. If a channel is programmed for a long tone (Programmable Function Value 4 2-6), the system will confirm its activation and deactivation with siren and alarm signals. If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel. The additional channel does not work in the VALET mode and in the alarm mode.
Inclusion of an additional channel: Sherkhan 5
Turning off the additional channel:
Note: If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel (programmable function 2-6)
Alarm mode
If the door, hood/trunk is opened in armed mode, the system will go into alarm mode for 30 seconds, alarms and sirens will last 30 seconds. At the end of 30 sec. the system will return to armed mode. If the shock sensor alarm zone is triggered (strong impact), the system will go into alarm mode for 15 seconds, the alarm and siren signals will last 15 seconds. At the end of 15 sec. the system will return to armed mode. When the warning zone of the shock sensor is triggered (weak impact), the system will not go into alarm mode, but will only issue a series of four short signals by the siren and alarm. You can stop the alarm mode by short pressing the keyfob button I. The locks will not be unlocked, and the system will switch from alarm mode to armed mode.
In alarm mode:
Reminder mode
If the communicator keyfob received an alarm signal from the door, hood/trunk, shock sensor, call sensor and you did not notice it immediately, then the keyfob, after transmitting the alarm signal, goes into reminder mode (short beeps and indication of the zone that caused the alarm mode) . To stop the reminder mode and check the state of the car, briefly press the button IV of the key fob or button I to exit the security mode and unlock the door locks.
In reminder mode:
Note: Keyfob communicator does not go into reminder mode when receiving a warning signal from a shock sensor (weak impact)
Car Owner Call
If you need to call the owner of the car, tap with a hard object (coin, keys, etc.) near the call sensor. The call sensor LED will flash in green. The function of calling the owner of the car is available immediately after arming. To stop the signals of the keyfob-communicator, press the button I of the keyfob. To stop the signals from the keyfob-communicator and check the condition of the car, briefly press the IV button.
When calling the car owner:
Access to the car without a key fob Sherkhan 5
Access to a car without a key fob may be required in a number of cases. For example, if the key fob is lost, if the battery in the key fob is dead, if you are relaxing on the beach and do not want to take the key fob with you (the key fob and keys are closed in the car). The SCHER-KHAN MAGICAR V system provides such an opportunity. To ensure that only you are allowed access, the system uses a personal code consisting of four digits. The value of each digit of the code can vary from 1 to 9. Thus, the code can have a value from 1111 to 9999. The code is entered and recorded through the call sensor of the car owner.
Recording a personal code:
In order for you to use this function, you must enter your code into the system memory. To do this, follow several steps:
- Turn on the ignition
- open the door
- While the LED is flashing, tap the call sensor the number of times corresponding to the first digit of the code. After 1.5 sec. the LED will confirm the selected number with red flashes and start flashing again.
- While the LED is flashing, tap the call sensor the number of times corresponding to the second digit of the code. After 1.5 sec. the LED will confirm the selected number with red flashes and start flashing again.
- While the LED is flashing, tap the call sensor the number of times corresponding to the third digit of the code. After 1.5 sec. the LED will confirm the selected number with red flashes and start flashing again.
- While the LED is flashing, tap the call sensor the number of times corresponding to the fourth digit of the code. After 1.5 sec. The LED will confirm the selected number with red flashes.
- You will hear one siren tone to confirm that the code has been programmed, and the alarm will flash once.
If you made a mistake on any of the steps, then you need to record the code, starting from step 1.
Entering a personal code:
- Tap the call sensor 10 times. Each time the LED in the sensor will flash green. The time between blows must be less than 1.5 seconds.
- The LED will quickly flash red to confirm that the previous step has been completed. If the LED does not flash red, then start from step 1 again.
- While the LED is flashing, tap the call sensor the number of times corresponding to the first digit of the code. After 1.5 sec. the LED will confirm the entry of the first digit with red flashes and start flashing again.
- While the LED is flashing, tap the call sensor the number of times corresponding to the second digit of the code. After 1.5 sec. the LED will confirm the entry of the second digit with red flashes and start flashing again.
- While the LED is flashing, tap the call sensor the number of times corresponding to the third digit of the code. After 1.5 sec. the LED will confirm the entry of the third digit with red flashes and start flashing again.
- While the LED is flashing, tap the call sensor the number of times corresponding to the fourth digit of the code. After 1.5 sec. the LED will confirm the entry of the fourth digit with red flashes.
- If the code is entered correctly, the system will disarm, the door locks will open, and the key fob-communicator will receive a signal to disarm the system. If the code is entered incorrectly, then the key fob will receive a call signal from the owner, and it will be necessary to repeat all the steps starting from step 1.
The system allows five attempts to enter the code within 30 minutes. If the code was entered incorrectly, then its entry is blocked for 24 hours or until you disarm the system using the key fob.
Battery protection (out-of-dimension warning)
The system helps protect the car's battery from being discharged. If you forgot to turn off the parking lights, then when arming, the key fob-communicator will give a series of beeps for 5 seconds. At this time, the images of the lock and side lights will flash on the display. The warning tone will repeat every 30 seconds. three times.
Starter or ignition lock
The system in armed mode will not allow you to start the car engine. When you try to start the engine in armed mode, the system will send an alarm signal to the key fob communicator. An alarm about turning on the ignition will be displayed by flashing side lights on the key fob communicator, sound and vibration signal. The engine blocking operation mode is selected when the system is installed at a service station and depends on the values of two programmable functions 1-4 and 1-8. You can find out more about blocking the engine of your car at the place where the system is installed. When the starter interlock is selected, the system will prevent the vehicle's starter from restarting if the engine is started in automatic mode.
Open door warning
The system warns of an open door (programmable function 1-2). When a custom function value is selected, the alarm flashes if the car door is open.
Protection of the radio channel from code interception
The system has special protection for the commands transmitted by the key fob. Each time you press a button on the system's key fob, the code message changes according to a special algorithm. This is done to protect the system from interception of the code and its selection (intelligent hacking of the security system). The code protection algorithm is specially designed for the SCHER-KHAN MAGICAR system and is unique, not applicable in one security system of other brands.
Motor protection in automatic start mode
The system in automatic start mode constantly monitors the operation of the engine. If the engine stops before the end of the warm-up cycle (engine failure or out of fuel), then no later than 20 seconds. processor unit system will turn off the ignition. Repeated automatic start of the engine will not be possible until the malfunction is eliminated. For vehicles with a manual transmission, you must perform the backup mode again.
Shock sensor sensitivity adjustment
You can adjust the sensitivity of the shock sensor depending on your requirements. A regulator is provided to adjust the sensitivity of the sensor. Turning the knob clockwise increases the sensitivity, and counterclockwise decreases it until the sensor turns off. Consult a service station about the location of the shock sensor, it must be easily accessible for adjustment.
Adjusting the sensitivity of the owner's call sensor
You can adjust the sensitivity of the car owner's call sensor depending on your requirements. To adjust the sensitivity on the sensor, a step regulator with three positions is provided. The extreme left position of the regulator corresponds to the minimum sensitivity of the sensor, the extreme right - to the maximum. The sensor should be located in the lower corner of the car's windshield.
Adjusting the volume of siren confirmation signals
You can adjust the volume of the siren's short beeps. To reduce the volume, you need to cut the loop from the wire on the siren's body. The system can be equipped with any siren according to the wishes of the owner, including those where there is no possibility of adjustment.
Backup mode (only for manual transmission)
The standby mode excludes the possibility of automatic starting of the engine if the manual transmission lever is not set to the neutral position. Depending on your requirements, you can choose one of three redundancy algorithms (programmable function 1-6).
Algorithm 1
Algorithm 2
To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:
- At the end of the trip, without turning off the engine, place the gear lever in neutral position
- Close the hood/trunk doors
- Remove the key from the ignition switch (in the OFF position). The engine will keep running
- Open the door and get out of the car. Close the door. The engine will stall.
Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.
If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, redundancy will be prohibited if the door, hood / trunk are open at the time the ignition is turned off.
Algorithm 3
To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:
- At the end of the trip, without turning off the engine, place the gear lever in neutral position
- Close the hood/trunk doors
- Press for 2 sec. key fob button II
- Remove the key from the ignition switch (in the OFF position). The engine will keep running
- Open the door and get out of the car. Close the door. Engine will stall
Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.
If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, the implementation of the reservation requires you to each time press button II of the key fob before turning off the ignition (by turning the key in the ignition switch to the OFF position).
ATTENTION!
Close the sunroof and windows before leaving the vehicle. Do not leave people or animals in the vehicle when the reservation mode is being executed.
Do not start the engine automatically if there are people or animals in the car.
Leave the gear lever always in the neutral position. Do not use automatic engine start on open top vehicles.
If the operation of the redundancy mode differs from the described algorithms or does not occur, urgently contact a service station for advice. Until the cause is removed incorrect operation do not use automatic engine start.
PROGRAMMING NEW KEYFOBS
The system can remember the codes of three key fobs. To program new key fobs, follow two steps.
- Turn the ignition key three times from OFF to ON. The alarm will flash once to confirm entry into programming mode.
- Not later than 4 sec. after the alarm flashes, press button I of the key fob, the code of which must be entered into the memory of the processor unit.
To exit the programming mode, do not take any action for 4 seconds. after writing the code of the last key fob.
If no action is taken after step 1, then after 4 seconds. the alarm will flash 2 times, the system will switch from the key fob programming mode to the VALET mode.
Note:
The system has three memory cells for storing key fob codes. When you try to write the fourth key fob, the code of the first recorded key fob will be deleted.
PROGRAMMING FUNCTIONS USING THE KEYFOB
Programming the CTCTS functions using a key fob consists of four steps.
- Entering the programming mode and selecting the programming menu. To enter Menu No. 1, press the I + II buttons simultaneously for 2 seconds. To enter Menu No. 2, press the I + IV buttons simultaneously for 2 seconds. The siren will sound one short beep and the alarm will flash once, confirming the successful completion of STEP 1.
- Press the IV button to select the Menu function you want to change. The number of presses must correspond to the number of the selected function. For example, to select function 4, you need to briefly press the keyfob button IV four times. Each button press will be confirmed by a short siren tone (if enabled) and an alarm flash.
- Wait a few seconds. The system will confirm the number of the selected function to be changed with short siren sounds and alarm flashes. The number of signals will correspond to the number of the selected function.
Note:
If, when choosing a function, you made a mistake with the number of clicks and (or) there are no siren and alarm signals, then you must repeat all the steps starting from STEP 1.
- Press the I button to select the factory setting for the function. To confirm this, the siren will give one short signal, the alarm will flash once. Press the II, III, or IV button to select optional function values. To confirm this, the siren will give two, three or four short beeps, the alarm will flash two, three or four times.
Note:
If you hear one long siren signal, this means the system has exited the function programming mode. To continue programming, repeat all steps from STEP 1.
ATTENTION!
If you need to change more than one function from the Menu you have selected, then the selection of each function to change must begin with STEP 1.
Menu of programmable functions
Menu #1 [Button (I+II)-]
| No. p / p. | Function | [Button (I)] Factory setting | [Button (II)] | [Button (III)] |
|---|---|---|---|---|
| 1-1 | Delay before the starter rotates after the ignition is turned on. Should be increased for a diesel vehicle. | 4 sec. | 10 sec. | |
| 1-2 | Open door warning | Not | There is | |
| 1-3 | The duration of the control pulse of the central lock. Should be increased for pneumatic central locking system | 0.8 sec. | 4 sec. | |
| 1-4 | "Panic" or JackStop mode (protection against robbery) | "Panic" (Starter lockout) | JackStop (ignition lock) | |
| 1-5 | Central locking control for turning the ignition on and off | Turned off | Turned off | |
| 1-6 | Launch reservation method. (Only for manual transmission) | Automatically, every time the ignition is turned off | Automatically, whenever the ignition is turned off, but provided that the doors are closed | Only manual mode, before switching off the ignition for reservation, it is necessary to press button II for 2 seconds. |
| 1-7 | Starter rotation time | Standard | Standard + Minimum | Standard + maximum |
Note on function 1-4: This function allows you to select the "Panic" mode or JackStop mode (protection against robbery):
Resetting all programmable functions of Menu No. 1 to factory defaults
- Entering programming mode. Press buttons I+II simultaneously for 2 sec. The siren will sound one short beep and the alarm will flash once, confirming the success of STEP 1
- Briefly press button III on the key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time, three siren sounds will sound, the alarm will flash three times, confirming the factory settings of all menu 1 programmable functions.
Menu #2 [Button (I+IV)-]
Setting all programmable functions of menu No. 2 to factory values Sherkhan 5
To reset the programmable features to factory defaults, two steps are required.
- Entering programming mode. Press buttons I+IV simultaneously for 2 sec. The siren will sound one short beep and the alarm will flash once, confirming the success of STEP 1
- Briefly press button III on the key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time after this, three siren sounds will sound, the alarm will flash three times, confirming the factory settings of all programmable menu #2 functions.
To autostart Sherkhan 5 from the key fob, press and hold button II for at least 2 seconds, as shown in the figure.
ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!
In this case, the car will forcibly switch to armed mode with the engine running. The doors will automatically enter the close mode, after which the system will be set to the engine start mode. If the process of starting the engine is successful, then the key fob will display information about the time remaining before the engine stops working in minutes-seconds, and smoke from the exhaust pipe. This time can be programmed in the modes of 15, 5, 25 minutes or 45. To make a trip without stopping the engine within the programmed auto start duration, it is necessary to open the driver's door, then insert the key into the ignition lock, turn it to the "Ignition On" position. The period of time between opening the door and turning on the ignition mode is limited to 20 seconds. This event is provided in order to increase the security of the car against theft during the warm-up period. If within 20 sec. the ignition will not turn on, the engine will stop.
If the engine start was unsuccessful, security system will try to start again. After the 3rd unsuccessful attempt, the car alarm will go into standby mode. To resume the autorun function, it is necessary to diagnose the engine and the main systems of the car. Possible reasons the fact that the engine autostart does not work:
- weak battery charge;
- extremely low temperature engine in the cold season;
- immobilizer problems limiting remote start engine;
- malfunction of the electrical equipment of the car;
- there is no control over starting the engine (the engine did not start, but there is smoke on the indicator, so a second attempt to start is not made);
- failure of other engine systems internal combustion associated with difficulty starting.
If the engine starts with the key, but the remote start does not work, it is necessary to reprogram the autostart system, reducing the start frequency, increasing the temperature response. Perhaps the problem will be fixed.
When starting the engine, the security system will signal the following signals. 
The car is not set to autorun, if during its production:
- the ignition is in the "On" position;
- one of the doors is open;
- the engine is already running;
- the "reserve" mode is not activated in cars with manual transmission.
In the event of a successful engine start, the devices will signal: 
In the case when the engine stops automatically, the devices generate signals: 
Programming autorun time intervals
The car alarm provides programming of time intervals (autostart time) after two, 4 and 8 hours. The choice of a specific option is made depending on the operating conditions of the car, the condition of the engine and the battery. To start the programming operation, it is necessary to simultaneously long press the buttons I and II. Next, you need to perform the following operations in the following sequence:
- Turn off the “timer” option (if it is activated) by briefly pressing buttons II and IV at the same time. The "timer" should be deactivated on the display.
- Press the IV button thirteen times. Each entry is confirmed by one siren signal.
- Wait for the siren to give a 13-fold sound confirmation of the entered information.
- Use the key fob buttons to confirm the selected autorun mode. Button II corresponds to the autostart mode after 8 hours, III - after 4 hours, IV - after two hours.
- Set to autostart by turning on the "timer" mode by briefly pressing buttons II and IV at a time.
Reprogramming the autostart mode according to the interior temperature
For correct activation of autostart according to the characteristics of the passenger compartment temperature, it is necessary to activate the start modes by time (1-13) before enabling the programming option. Next, you need to switch to the programming mode by long pressing the corresponding buttons on the key fob I + II. Then the following operations are performed:
- Turn off the "timer" mode (if it is activated), as described in the previous paragraph.
- 21 times methodically press the IV-th button, after which the siren will signal.
- Wait for the siren alarm 21 times in a row.
- Set the desired autostart temperature mode: button IV - plus 60 degrees Celsius, III - minus 25, II - minus 15.
- Activate the timer mode.
Warm-up programming
The warm-up time can be set to fixed intervals of 5, 15, 25 minutes or 45 minutes. To do this, activate function 1-12 in mode II. Programming is entered by long pressing I + II, after which the following operations are performed:
- Button IV is pressed twelve times (accompanied by a sound signal).
- 12-fold siren signal - confirmation.
- The engine operation time is selected by activating buttons I (5 minutes), II - 15, III - 25 or IV - 45 minutes.
Programming autostart by the voltage of the on-board network
Autostart can be programmed when the battery is discharged to an amplitude of 11.5 volts. First you need to activate the start by time (1-13), then enter the programming by long pressing I + II. Here are the buttons to press:
- 20 consecutive IV button presses.
- Waiting for the siren to sound 20 times.
- Activate the battery voltage response mode with button II.
Autorun problems
Some vehicles have the following autostart problems:
- When the ignition is turned off, the car does not stall. To disable autorun, you need to open and close the doors. To correct the problem, function 1-16 (Button II option) is required. In this case, in order to turn off the engine, it is necessary to switch the key to the "Ignition Off" position.
- Activation of the "Valet" mode after emergency disarming (zzz symbols on the key fob). To fix the problem, simultaneously long (more than 2 seconds) press the I + III buttons.
- If it is necessary to urgently turn off the car from the key fob during the autostart period, it is necessary to long press the II button.
Wanting to understand how to enable autorun on Sherkhan 5, you should study the instruction manual, know the principle of operation and the modes implemented in this system car alarm. It is controlled by using a switching key fob with an LCD display, via a radio channel. Broadcasting of signals is carried out at a distance of up to 1.5 km.
The device is equipped with cars equipped with a gasoline or diesel power unit, with a voltage in the on-board network of 12 W. The alarm system has the option of automatically starting the engine by activating a command from the key fob or starting from a timer.
Preparation for work
How to enable autorun on Sherkhan 5 is presented below, but first the alarm must be prepared for work. Before you start using the key fob, you will need to perform certain actions aimed at its correct activation. The fact is that in order to maintain a full charge of the battery, manufacturers supply the power supply separately from the main device.
To install the battery in the provided compartment, you should carefully remove the latch that holds it in closed position cover of the respective compartment. As a rule, this operation does not cause any problems, since the body and other elements of Sherkhan 5 are made of high-quality and high-strength materials.
The next step involves moving the key fob cover opposite to the antenna and placing the battery in the compartment with the polarity observed. After adequate installation of the specified part, a characteristic melodic sound should be heard, after which it is necessary to reinstall the cover and retainer.
Auto start setting
Enabling autorun is described in detail in the presented step-by-step instructions:
Button press modes differ in two ways (important):
- Short-term activation - a single impact on the key, lasting no more than a second, which is accompanied by a short signal;
- Long press - fixing the button for more than 2 seconds until a sound notification appears, after which you can release the key.
Further tuning of the engine excitation programming is shown using functions 1-12 for 25 minutes as an example. First you need to enter the settings mode No. 1, activate buttons 1 and 2 at the same time. Hold them until the remote control beeps. If the manipulation is carried out correctly, the alarm will be in the programming sector.
Next, you need to carry out successive touches of button No. 4 in the amount specified by the program. Each click must be confirmed a specified number of times. In this example, 12 clicks. At the end of activation, you should hold the button for 3-4 seconds, after which, the device will confirm the programming item with sounds in the amount of 12 notifications.
Features on a specific example
The autorun settings of Sherkhan 5 every 2 hours or when the temperature in the cabin drops to -15 ° C, with the cabin warming up for 25 minutes, perform the following manipulations:
- At the same time, buttons I and II are activated, then, pressing VI twelve times, and finally, holding the button III (functions 1-12 are configured taking into account the temporary value of 25 minutes);
- Activators I and II are pressed simultaneously, button No. VI is clicked 13 times (alarm functions No. 1-13 are set to a time indicator of 2 hours;
- Perform pressing simultaneously I + II and VI - 21 touches (function 1-21 is set to a temperature of - 15 ° C).
