How to set auto start on the Sherkhan alarm 5. Programming the Scher-Khan car alarm key fobs. Remote start mode

Backup mode (only for manual transmission)

The standby mode excludes the possibility of automatic starting of the engine if the manual transmission lever is not set to the neutral position. Depending on your requirements, you can choose one of three redundancy algorithms (programmable function 1-6).
Algorithm 1

Algorithm 2

To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:
At the end of the trip, without turning off the engine, place the gear lever in neutral position
Remove the key from the ignition switch (in the OFF position). The engine will keep running
Open the door and get out of the car. Close the door. The engine will stall.

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, redundancy will be prohibited if the door, hood / trunk are open at the time the ignition is turned off.
Algorithm 3

To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:
At the end of the trip, without turning off the engine, place the gear lever in neutral position
Close the hood/trunk doors
Press for 2 sec. key fob button II
Remove the key from the ignition switch (in the OFF position). The engine will keep running
Open the door and get out of the car. Close the door. Engine will stall

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, the implementation of the reservation requires you to each time press button II of the key fob before turning off the ignition (by turning the key in the ignition switch to the OFF position).

Example notation:

I - quick (0.5 sec.) button press

I - long (2 sec.) button press

(I + II) - fast (0.5 sec.) simultaneous pressing of the buttons (combination of buttons)

(I + II) - long (2 sec.) simultaneous pressing of the buttons (combination of buttons)

Note:

With a long 2 sec. pressing the I button, the car alarm operation modes are sequentially changed in the order (1) > (2) > (3) > (1) .... In mode (2) the "Hands-free" function has a long working range - the symbol flashes.

Setting the time on the keyfob-communicator display

Setting the current time is required before starting the operation of the system or when changing the key fob battery. Follow the steps according to the table below.

ATTENTION!

Setting the correct time is necessary condition for correct operation automatic start of the engine by timer.

Setting the key fob-communicator modes.

Vibration call, owner call, temperature display standard "°F" or "°C"

To set the desired operation mode of the car alarm key fob, follow the steps in accordance with the table below.

When installing a modern and multifunctional alarm system on a car, you need to understand the procedure for using and possible mistakes. Such systems include the Sherkhan 5 alarm system. It is also important to entrust the initial installation and debugging of work to professionals.

Purpose of the alarm

Car alarm Sherkhan Magikar 5 belongs to the category of devices with signal control through a separately dedicated radio channel. Mutual communication between the key fob-communicator of the user and the process control unit is distinguished by the possibility of signal transmission over a distance of up to 1.5 km.

The system, taking into account its high functionality, performs a number of security operations:

• engine blocking with protection of system components;
• engine autostart with the possibility of taking into account individual parameters;
• sound accompaniment of security siren hidden from access.

The main functions are feasible through the implementation of auxiliary operations that can be activated by the user.

All functions of the security system

Even correct installation does not allow you to use possible functions without debugging and testing them. Therefore, you should carefully study all the provisions Magicar instructions 5. Separately, you should consider the possibilities of the key fob, processor unit and some technical parameters.

Key fob functionality

The device has a liquid crystal operating screen and is made in one housing with 4 control keys. Among the main functions are:

1. Security code . Using Sherkhan 5 Magic Code, all signals are protected during transmission.
2. Control of executed commands through audio and video support.
3. Discharge level indication Car battery.
4. Engine run time display after autostart, current time.
5. Running engine reminder.
6. Interior temperature display cars.
7. Reminder of received alarm messages.
8. Manual remote motor start symbol.
9. Processor operating functions

When interacting with the key fob, the Scher alarm processor Khan Magicar 5 generates the following commands:

• engine starting in automatic mode when specifying one of the two options for the transmission unit (automatic transmission or "mechanics");
• setting offline start interval(2, 4, 8 or 24 hours) or conditions (when certain temperature in the cabin or antifreeze);
• issuing a command to force the engine to start;
• engine stability control;
• setting the algorithm for starting the motor, taking into account the features - the type of engine, starter operation time, etc.;
• task of personal identification codes for signaling scher if the key fob or key is lost;
• the ability to set the auto protection mode after starting the engine, priority unlocking the driver's door;
• performance of service functions: light off delay, automatic arming of the car - "without key fob".

Such a wide functional range would not have been possible without the task of excellent technical abilities.

All technical features

To perform its functions, the security system uses several methods to protect electrical networks:

• installation of slow-acting fuses taking into account the connection scheme;
• using internal combustible resistors when the current is exceeded;
• installing internal transistors;
• using directional diodes in case of a change in the direction of the current;
• installation of varistors for protection against voltage surges or when creating impulse noise.

The alarm has a wide operating temperature range (-40°C - +50°C), low current consumption (no more than 35 mA in standby mode) and a small unit weight - 270 g. Such indicators indicate a well-thought-out and effective system.

In the alarm mode, the Sherkhan 5 alarm system can work in one of three ways:

• sound siren (continuous signal, duration 30 seconds);
• optical signal(triggered by an alarm, the sound is intermittent at a frequency of 1 Hz for 30 seconds);
• radio signal(the time interval of the sound notification is 100 seconds, the sound itself is intermittent with a frequency of 0.35 Hz).

At the same time with general protection vehicle operating instructions indicate the presence of additional protection barriers, in particular:

1. Objects under protection. Sensors for controlling the opening of doors, trunk, hood, shock. When you try to open, an alarm sounds (30 seconds) with the impossibility of turning off after arming.
2. Radio communication channel with the system. Provides constantly changing coding of the transmitted signal.

Food for consumers is provided by the following sources:

1. Processing unit- car battery - 12V.
2. key fob switch- built-in battery class "AAA" - 1.5V.
3. Keychain– 2 built-in batteries of class “CR2025” – 6V.

For customizing operating modes and full use security system you should remove the protection against the discharge of the battery of key fobs, and get acquainted with the symbols and purpose of the buttons. If the key fob does not work, the gasket between the contact and the battery is removed. The beginning of the work will be a confirming characteristic melody.

Using key fobs Sherkhan 5

The functionality of the switch corresponds to the symbols specified in the operation manual and is expressed in the following positions:

• low battery indication and switch to power-saving mode;
• auto parameter status display- battery voltage, interior temperature, current time;
• Valet mode indicator;
• guard mode symbol, unlocking and locking locks;
• sound indicator;
• display of disabled shock sensor;
• vibration alert enabled;
• using passive arming;
• activation of the mode free hands» ;
• indication open doors or hood;
• engine start display or using the ignition lock;
• indication of the included parking lights;
• active timer start mode;
• Turbo mode activation;
• call sensor activation;
• alarm mode display when the secondary shock sensor is triggered.

For effective use of all possibilities, you will need to deal with the question of how to configure and how to enable individual functions. Programming is carried out from a key fob with 4 working buttons. To facilitate the order of use, you should assign serial numbers to the keys:

1. Lock button– I.
2. Key with open lock and key– II.
3. open trunk– III.
4. Question mark - IV.

Correct operation of the Scher Khan car alarm is possible only if the correct time is set. This is required when using the alarm for the first time or after changing the batteries.

Installation is carried out according to the following algorithm:

Step 1. Press the combination of buttons II + III, hold for 2 seconds. The programming mode is called.
Step 2. Press the I button, hold for half a second. The mode for changing the current time is activated.
Step 3. Press the I button again, hold for half a second. Set the clock rate.
Step 4. Press button II, hold for half a second. Set the minutes.
Step 5. Press the combination II + III, hold for 2 seconds. We exit the programming mode (confirmed by sound).

Only when the time is set, it becomes possible to link the alarm to the engine start by timer.

Further configuration is related to the activation of operating modes. To learn how to program the work, you should study the following algorithm:

Action 1. Press the II + III buttons, hold for 2 seconds. The programming mode is activated.
Action 2. Press button III, do not release 0.5 sec. The vehicle call mode becomes available. Confirmed by the appearance and symbol of the lifted handset.
Action 3. Press and hold the IV button for half a second. The key fob vibration mode is called.
Action 4. Press the combination I + IV for 0.5 seconds. Change the temperature format.

Successful execution of the second step will occur when the functions are activated no later than 15 seconds after the end of step 1.
When using key fobs in the dark, the backlight is activated by briefly pressing the "III" key. In the same way, the backlight turns off.

Now the alarm is ready to work, but for correct operation, you should study some questions on how to use individual modes.

Alarm operating modes

Regular use of the alarm brings all the actions of the owner to automatism. But on initial stage you need to find out all the nuances of individual operating modes.

Arming and passive mode

The main operating mode is arming the machine. Its activation should be carried out with securely locked doors and hood and trunk lids. In this case, press the "I" key. Successful action will result in:

1. For siren signal- single signal.
2. For alarm - one-time flash.
3. Built-in LED- runs at a frequency of 1 time per second.
4. Switch Display- 5-fold blinking of the "headlights" of the car with the transition to the indicator of the closed lock.
5. Key fob signal- a single beep.

In the future, the system will automatically put the following components into operation:

• door, hood and trunk sensors;
• shock sensor - 30 seconds after the start of work.

When operating the alarm, it should be taken into account that if one of the doors is not tightly closed, the protection is activated bypassing the sensor of the marked element. In this case, the ignition is still blocked. In the future, working capacity in full protection mode is easily restored.

When using the light delay function in the cabin, you should program the function to delay the start of arming the car for this time.

The need to protect a car with a running engine arises when the car warms up, leaves the passenger compartment for a short time (if it is necessary to open the gate, etc.). The function is programmed by activating the "Passive" command under index 1-5. The start of passive protection is accompanied by the same inscription on the display of the switch.

Alarm message

When an intrusion attempt is made, the alarm goes into alarm mode. This is expressed in the following manifestations:

1. Sound signal and emergency– works within 30 seconds.
2. Internal indicator- blinking with a frequency of 1 second.
3. Display - the symbol blinks according to the cause of the alarm.
4. Key fob operation - initial intermittent signal (30 sec.) followed by a reminder every 2 sec.

The system is transferred to the armed mode by pressing the "I" or "II" buttons, or there is an automatic transition after the first 30 seconds of the alarm. If the factor continues to be affected, the alarm mode will be used 8 more times. When the shock sensor is activated, the alarm state lasts for 15 seconds according to a similar algorithm.

Disarming

In the normal disarming mode, the II key is used. Process completion confirmation is accompanied by:

1. For siren signal- double signal.
2. For alarm- double flash.
3. Built-in LED stops working.
4. Switch Display- 5-fold blinking of the "headlights" of the car with an indication of an open lock.
5. Key fob signal– 2x short beep.

Safe mode involves entering a PIN code after pressing the "II" key once and using it again. This feature is activated via the setting mode function with index 1-19. Activating channel 2-11 allows you to use the function step by step opening doors.

Remote start mode

The engine is started for warming up by pressing the "II" button for 2 seconds. In this case, the car is armed and the engine starts. The keyfob-switch reports the time until the engine stops in the reverse timer mode.

To answer the question of how to reset the engine run time, use the programming mode (function 1-12). The warm-up time is set in the range of 5-45 minutes in increments of 10 minutes.

Additional features

Among additional features It should be noted:

1. Panic mode. Activated by pressing the IV button for 2 sec. and stops the engine from starting automatically. After 90 seconds, the system switches to the standard armed mode.
2. Jack stop mode. It involves stopping the engine forcibly (even while driving). It is set as an alternative to the "Panic" mode through a task in the "Programming" section. Both modes are canceled after a short use of buttons I or II.
3. Valet mode. Allows you to not use the door lock. This function is used when visiting a car service. The I+III buttons are shared for 2 seconds.
4. Timer remote start . Used when the engine needs to warm up.

The mode is activated according to the following algorithm:

Step 1. Press the combination of buttons II + III (hold for 2 seconds). The programming mode is activated.
Step 2. Press and hold for 0.5 seconds. button II. Go to the timer setting mode.
Step 3. With the I button we change the hours, with the II button we set the minutes.
Step 4. We exit the mode using the II + III combination (press, hold for 2 seconds).

If you need to turn on the function, or if a question arises - how to turn off the timer, they equally use a short press of the buttons II and IV.

Violations of normal operation

Operating experience allows us to call Sherkhan 5 reliable signaling- at the level of Starline A8 and Starline E90. However, some malfunctions still occur during the operation of the equipment:

1. Sensor failure. One of the most common causes is wire breakage, contact damage.
2. Malfunction in Valet mode. When activated, the system does not close the doors.
3. Refusal to execute commands from the key fob. If the battery is in good condition, the failure may be caused by damage to the antenna.

In the event of a complete failure to work, allow the most simple reasons failure. You should not be interested in how to flash the system again before checking the power supply to the processor.

To correct failures, comments and reviews on the forums do not always help. If a possible ways eliminations have been used, and the malfunction has not been eliminated, the restoration should be entrusted to specialists. Preliminary specify the malfunction and you will be answered how much the repair costs.

With the timely diagnosis of problems, the car will always be under reliable protection.

MANUAL

PURPOSE OF THE BUTTONS OF THE KEY FOB-COMMUNICATOR

Example notation:

I - quick (0.5 sec.) button press

I– – long (2 sec.) button press

(I+II) - fast (0.5 sec.) simultaneous pressing of the buttons

(I + II) - - long (2 sec.) simultaneous pressing of the buttons

Number

buttons

Time

pressing

Function (mode)

Enable security mode

Stop alarm mode

Enable starter/ignition interlock

close locks

Disarm

Stop alarm mode

Disable starter/ignition interlock

open locks

Enable/disable the "Free

Turn on/off display backlight

Checking System Status

open trunk

PANIC or JackStop™ modes. For

stop press button I or II

Enable/disable siren signals

Additional management channel 1

Shock sensor enable/disable

Additional management channel 2

Enable/disable timed start

TURBO mode enable/disable

Enter programming menu 1

SCHER-KHAN MAGICAR 5

1) Factory value. Two step disarming is disabled. For
disarming, just press the button "II" of the key fob
2) Confirmation of disarming is required. If using the code
PIN1 disabled (programmable function 1-6 in factory setting),

it is necessary to press the button "II" of the key fob again. If used

four- or two-digit PIN1 code (programmable function 1-6

has the value II or III), it is necessary after pressing the button "II" of the key fob

sequentially press four (or two) buttons on the key fob with numbers,

the corresponding digits of the PIN1 code. Only after correct

the second step, the system will be disarmed. If the code is not

entered within 15 seconds or an incorrect code is entered, the system will go

into a state of alarm

Programmable function 1-20: "Auto start
by voltage battery»

to perform an automatic start timer.

This programmable function has two meanings:

1) Factory value. Automatic voltage start
battery is not used
2)
the battery voltage does not drop below 11.5 V, or

the temperature condition assigned to the programmable

function 1-21

Programmable function 1-21: "Auto start
temperature threshold"

This function allows you to enable or disable the corresponding condition

to perform an automatic timer start, and select

temperature threshold.

This programmable function has four meanings:

1) Factory value. Automatic threshold trigger
temperature value is not used
2) The next timed start will be delayed until
the temperature will not drop below -15

C or battery voltage is not

Programming the Sherkhan 5 key fob may be needed in the following cases:

1. The alarm does not turn on and off from one remote control, others work fine.
2. Hull damage or printed circuit board switch.
3. Incorrect operation of the main unit and remote control.
4. Use of additional key fobs.

Three pagers can be stored in the memory of the anti-theft system. This is not difficult to do, but the procedure has its own characteristics.

Binding a new key fob to the Scher Khan Magicar 5 alarm

The instruction manual will help you to record a new communicator into the memory of Magikar 5. Please read it carefully before performing any operation on the remote control.

The key fob of the anti-theft system can be programmed only when the security mode is disabled. If you are connecting new remotes, do not forget to overwrite the old ones, otherwise they will be deleted from the system memory.

1. For four sec. switch the ignition on and off three times. The lights will flash once. The programming mode has been entered.
2. Enter the remote control code by pressing button 1. This must be done within four seconds. The vehicle lights will turn on once.
3. If necessary, record the following switches in the same way.
4. Do nothing for four seconds after programming the last remote control and the system will automatically exit the settings.

Firmware and reprogramming Sherkhan 5

You can reflash the Magikar 5 version keychain using a PIN code. Record remote control codes by following the instructions below.

1. Turn the ignition key from "Off" to "On" three times within four seconds. Switch off the ignition.
2. Switch the ignition back on within four seconds. The number of inclusions must match the first value secret code. The light optics will light up once, confirming that a second value can be entered.
3. Turn on the ignition. The number of inclusions must correspond to the second digit of the code. The "emergency" flashes once, confirming the correct action.
4. Enter the rest of the secret number in the same way.
5. After entering all the numbers, press button 1 of the switch. The lights will flash once, confirming the pager entry. After four seconds, the system will exit programming mode.

An additional Magicar 5 keychain is not prescribed: reasons

There are frequent situations with the anti-theft system communicator when it is not programmed. There are a number of reasons for this:

• the remote control is damaged;
• the "Jack" mode is activated;
• the system does not recognize the "ignition on" command.

If it is not possible on your own, having tried all the options, register the key fob, you should replace it with a new one or contact the service center.

Autorun setup instructions

Starting the engine is a very convenient function of the security system. Having carefully studied the instruction manual, every motorist will be able to start the car from the key fob on their own. Before programming, disarm the car, turn off the ignition, turn off the "hands-free" mode, just in case, open one door.

Time setting.

1. To enter programming, simultaneously hold down keys 1 and 2.
2. Enter the timed autorun settings by pressing button 4 thirteen times. After each press, the system should emit a single beep.
3. You take right time auto start: button 2-8 hours, 3-4 hours, 4-2 hours.
4. Then start the timer by pressing buttons 2 and 4 at the same time. The display will show the “timer” symbol.

Automatic start of the engine by temperature.

1. Enter programming mode: buttons 1 and 2.
2. Press the 4 key twenty-one times.
3. You take required temperature: key 2 - (-15), 3 - (-25), 4 - (+60).
4. Start the timer by pressing 2 and 4 at the same time. The display will show “timer”.

How to remove the Jack mode without a keychain

On the Sherkhan alarm, it is quite easy to accidentally turn on the “Valet” mode by accidentally pressing it. Very often this is mistaken for a system breakdown: the alarm does not respond to shocks, autostart fails, key fobs are not programmed, the LED is constantly on. Only central locking and trunk opening works.

To turn off the "Jack" without a key fob, use the multifunctional button located in a prominent place.

1. Turn on the ignition, do not start the engine.
2. Hold down the multifunction key for two seconds. "Valet" is disabled.

Are all Sherkhan Magicar 5 keychains interchangeable?

The alarm panel is such a thing that is constantly lost, forgotten, broken, falls into the water. It is not possible to connect a second key fob due to its absence. Replacement with the original remote is also unrealistic. You have to look for a family communicator more or less compatible with yours. The pager may be completely, partially, or not at all. The compatibility of key fobs of the Sherkhan Magikar 5 anti-theft system was considered by us.

Video help to activate remotes