Installation of a gas boiler and its connection to the system is the most effective method organization of heat supply in a house or apartment. Control services have special requirements for the premises. To install a gas boiler, it is necessary to carry out a number of preparatory work.
The installation of equipment is preceded by measures to adapt the premises in accordance with applicable requirements. They are detailed in Specifications issued by Oblgaz or Gorgaz. This is relevant for organizing heating on liquefied or natural gas. But usually, in the latter case, the issuance of an official permit is neglected, which can lead to a serious fine and a ban on the use of the existing heat supply system.
The document regulating the requirements for the premises for the installation of gas heating boilers is developed on the basis of the following regulations:
- SNiP 31-02-2001. Designed for control construction works and building design.
- SNiP 42-01-2002. Describes the rules for organizing gas distribution systems.
- SNiP II-35-76 in the latest edition of 2012. They are guided by the choice of boilers and similar gas equipment.
- SNiP 42-01-2002 and SP 41-104-2000. Needed to comply with standards when designing autonomous sources of heat supply.
It can take a long time to study these documents. In fact, about 20% of their content is devoted to the organization of domestic heat supply using gas boilers. To avoid wasting time, we recommend that you familiarize yourself with useful excerpts from regulations.
Requirements for the organization of the boiler room
If the boiler power does not exceed 200 kW, any built-in rooms of the house can be used as a boiler room. These include basement and basement rooms. For boilers up to 30 kW, the minimum room volume must be at least 7.5 m³. Accordingly, for equipment from 30 to 60 kW - 13.5 m³, more than 60 kW - from 15 m³. You also need to take into account other characteristics of the boiler room.
These include the following requirements:
- square air vent for gas boilers up to 30 kW - 0.02 m², from 30 to 200 kW - 0.025 m² ();
- the distance from the protruding parts of the equipment to the walls is regulated by the manufacturer;
- the presence of a transom or window to reduce the concentration of gas in case of leakage, providing a three-fold replacement of air in 1 hour;
- natural and artificial lighting premises, the ratio of window area to volume - 0.03 m² per 1 m³;
- if the boiler room is located on the first or basement floor, they must equip a separate passage, the door must open outward;
- ceiling height - not less than 2.5 m;
- a refractory material is installed on the walls in the boiler installation area, the fire resistance limit of which is at least 0.75 hours.
Placement of heat supply components is free. The main requirement is that nearby objects should not interfere with repair or maintenance work.
Characteristics of the kitchen for the installation of a gas boiler
The power of most gas boilers rarely exceeds 30 kW. This makes it possible to install them in the kitchen of a house or apartment. This is also done by agreement of the controlling organizations. Many of the above rules apply for this case, but given the specifics of the premises, there are additional ones. for boiler with open cam combustion is provided with a three-fold exchange of air within one hour;
In practice, preparing the kitchen will require much less effort. Thus, ventilation can be provided by installing a lattice or a gap of 0.02 m² in the lower part of the door.
These rules are not "ultimate truth". The main document for preparing the boiler room for the installation of gas equipment will be the Technical Conditions.
Gas is still the cheapest type of fuel. Accordingly, the most cheap heating produced on natural gas. True, the installation of a gas boiler is associated with certain difficulties - the premises must comply with fire safety standards.
A separate room is required for the installation of powerful gas boilers
Gas boiler installation standards
To ensure that there are no troubles when taking the gas boiler into operation, it is necessary to choose the installation site in accordance with current regulations. The installation of a gas boiler in a private house (single-apartment or block) is regulated by SNiP 31-02-2001, and the installation rules in apartment buildings registered in SNiP 2.08.01.
For private houses
According to the norms, a gas boiler can be installed in a ventilated room, which is located:
- on the first floor of the house;
- in the basement or basement;
- in the attic:
- gas boilers power up to 35 kW (according to MDS 41.2-2000 up to 60 kW) can be installed in the kitchen.
With regard to the installation of boilers in the kitchen, two norms are currently in force at once. According to one document, heating devices with a power of no more than 35 kW can be placed, according to another - no more than 60 kW. And it's only about heating appliances. gas stoves or other equipment using gas is not taken into account.
What to do? You need to find out what norms are followed in your GorGaz. After all, it is their representatives who will take the equipment into operation. Actually, the designer should tell you all the subtleties, but it is also desirable to know this - you will need to prepare the room for installation.
Where to put
Now about where and how you can place gas equipment different power. We are talking about gas boilers and their power is summarized:
- with a power of up to 150 kW inclusive - in a separate room on any floor, including the basement and basement;
- from 151 kW to 350 kW inclusive - in a separate room of the first, basement or ground floor, as well as in a separate attached room.
More powerful installations in private homes are not used.
Requirements for kitchens in which a gas boiler is installed
When placed in the kitchen flow gas water heater or heating boiler on gas with a power of up to 60 kW, the room must meet the following standards:
There is one more thing that is not spelled out in the norms, but which exists: the installation of a gas boiler is only allowed in a room with doors. In the light latest trends- remove partitions, and instead of doors to do - this can be a problem. Without a door, permission will not be signed. Exit - put or . Another option is glass doors. They do not "load" the interior, but they are perceived precisely as doors.
All these requirements must be met. With violations, you simply will not sign the act of acceptance.
Requirements for individual rooms
Similar, but there are some differences:
- Ceiling height - not less than 2.5 m;
- The volume and area of the premises are determined by the convenience of maintenance, but should not be less than 15 m 3.
- The walls leading to adjacent rooms must have a fire resistance limit of 0.75 hours and a zero limit for the spread of fire along the structure (brick, concrete, building blocks).
- The hood with the same requirements: for outflow - a three-fold exchange, for inflow in the same volume, plus air for combustion.
- The room must have a window. Glass area - not less than 0.03 m 2 per cubic meter of volume.
If the equipment is installed with a power of 150 kW or more, one of mandatory conditions- the presence of an exit to the street. A second exit can be equipped - in utility room(not residential). It can be a pantry or a corridor. Doors must be fireproof.
Please note that when calculating windows, the area of \u200b\u200bglass is considered, and not the size of the window opening. Moreover, in some cases, they require the presence of at least one glass with an area of \u200b\u200bat least 0.8 square meters. If it is problematic to enlarge the windows, you can make a similar window in the door (the standard does not say that it should be in the wall).
How to attach boiler rooms
Sometimes in the house there is no way to allocate a separate room. In this case, the boiler room is attached. The standards for ceiling height, volume, glazing and ventilation remain the same as for individual rooms, only more specific rules are added:
Please note that the extension must be registered. Without official documents on it, no one will carry gas to you. And one more thing: when designing it, lay down all the norms without deviations, otherwise they will not be accepted. If the installation of a gas boiler is planned in an existing room, some deviations may be overlooked or some compensation may be offered (if there is a missing volume or ceiling height, they may be asked to increase the glazing area). For newly built buildings (and extensions too) there are no such discounts: they must include all the standards.
United kitchens
Today it has become fashionable to have or. It turns out a single large space in which it is easy to implement design ideas. But, gas service regards such a room as residential and prohibits the installation of gas equipment.
It will not be possible to solve the problem with a studio apartment, but there is a way out with a combined one. If you are just planning to combine the kitchen and the living room, when you draw up the documents, call the resulting room the kitchen-dining room. This space is not residential, so there will be no restrictions. If the papers are already issued, you can try to redo them or go the other way - install sliding partition. True, in this case, the alteration of documents will be required.
Place for installation of a gas boiler
Speaking specifically about apartments, they install gas boilers in them mostly in the kitchens. There are all the necessary communications: water supply, gas, there is a window and an extractor hood. It remains only to determine appropriate place for the boiler. For such an installation, wall-mounted (mounted) boilers are used. They are mounted on several hooks attached to the walls (they usually come with the kit).
As for installation in other rooms of an apartment or house, as a rule, none of them pass the requirements. For example, the bathroom does not have a window with natural light, the corridor usually does not fit in size - there are not enough tolerances from the corners or to the opposite wall, there is usually no ventilation at all or it is not enough. With pantries the same trouble - there is no ventilation and windows, there is not enough volume.
If there are stairs to the second floor in the house, often the owners want to put the boiler under the stairs or in this room. In terms of volume, it usually passes, and ventilation will have to be made very powerful - the volume is considered to be in two levels and it is necessary to ensure its triple exchange. This will require several pipes (three or more) very large section(not less than 200 mm).
After you have decided on the room for the installation of a gas boiler, it remains to find a place for it. It is selected based on the type of boiler (wall or floor) and the requirements of the manufacturer. The data sheet usually details the distances from the wall to the right / left, the installation height relative to the floor and ceiling, as well as the distance from the front surface to the opposite wall. At different manufacturers they may differ, so be sure to read the manual carefully.
Installation standards according to SNiP
- Gas boilers can be installed on fireproof walls at a distance of at least 2 cm from it.
- If the wall is slow-burning or combustible (wooden, frame, etc.), it must be protected by fireproof material. This may be a three-millimeter sheet of asbestos, on top of which a sheet of metal is fixed. Plastering with a layer of at least 3 cm is also considered as protection. In this case, the boiler must be hung at a distance of 3 cm. The dimensions of the fireproof material must exceed the dimensions of the boiler by 10 cm from the sides and bottom, and from above must be 70 cm more.
Questions may arise regarding the asbestos sheet: today it is recognized as a material hazardous to health. You can replace it with a layer of cardboard from mineral wool. And keep in mind that a fireproof base is also considered ceramic tile, even if it is laid on wooden walls: adhesive layer and ceramic just give the required fire resistance.
The installation of a gas boiler relative to the side walls is also regulated. If the wall is non-combustible, the distance cannot be less than 10 cm. For combustible and slow-burning, this distance is 25 cm (without additional protection).
If a floor standing gas boiler is installed, the base must be non-combustible. On the wooden floor make a non-combustible stand. It must provide a fire resistance limit of 0.75 hours (45 minutes). These are either bricks laid on a spoon (in 1/4 of a brick), or thick ceramic floor tiles, which is placed on top of an asbestos sheet fixed to metal sheet. The dimensions of the non-combustible base are 10 cm larger than the dimensions of the installed boiler.
Despite the standardization heating equipment, each manufacturer offers, albeit few, but different solutions. The Italian manufacturer of boilers - Ariston - also does just that. It's time to figure out how perfect its products are, and how it differs from the products promoted by competitors.
Peculiarities
A gas boiler is considered the most practical and economical source of heat in any area where pipes of main gas pipelines are laid. It is this equipment that largely determines how consumers will feel the advantages of heating with “blue” or liquefied fuel. Although Ariston boilers were created by Italian engineers, yet specific Russian conditions properly taken into account.
The created systems were initially designed with the expectation of:
- unstable and often low gas pressure;
- insufficiently sustained tension;
- contaminated water ingress;
- extremely cold winters with heavy rainfall and violent winds.
The functional parameters of the systems are approximately the same, neither type nor model-specific fee special significance Dont Have. The main difference concerns external perception, the size of the boiler. Of course, one cannot but mention the fact that, like other manufacturers, there is a clear distinction between single-circuit and double-circuit models. A useful option is the auto function, when using which the adjustment to the necessary parameters occurs automatically. In addition, any boiler of the Italian concern is equipped with a built-in automated unit for discharging excess air, protected from freezing and accumulation of scale and other dirt.
Kinds
To properly evaluate the characteristics of wall-mounted boilers, you need to refer to individual models. And special place among them is the double-circuit Alteas X. This device is classified as a premium heating technology designed for the highest thermal performance. The designers took care of the possibility of remote control via the Wi-Fi module. In the presence of mobile internet You can monitor the operation of the device anywhere in the world.
Information is displayed through a matrix display. What exactly they will be depends on the consumer (everything is flexibly configured). The boiler menu is 100% Russified. The system uses a modulating pump that consumes 30% less electricity compared to simpler analogues. The device develops an efficiency of 93.6% under favorable operating conditions. In addition to purely technical and consumer advantages, the stylish appearance of the boiler is also important.
This model can be seriously competed with the Cares mechanism. It is also mounted on the wall and also works with two circuits at the same time. But at the same time, it ensures the effectiveness of work in 93.8%. Heating can be programmed, for this purpose compatible two-position control devices are usually used. Aluminum is used in the production of the primary heat exchanger premium with excellent corrosion resistance and thermal efficiency.
Secondary circuit in contact with tap water very durable and long lasting. At the same time, he is able to give in 60 seconds required heat 13.6 liters of water. Both in the heating circuit, and in the hot water supply system, and in the boiler feed channel, filters are installed to prevent the ingress of mechanical impurities. For all its excellence, Cares is indifferent to harsh operating conditions. Even if the water pressure drops to 5 mbar, and the temperature outside drops to minus 52 degrees, this will not affect the quality of work.
In some cases, there is no need for hot water supply, you only need to heat the house (or vice versa). Such situations make the single-circuit boiler Ariston Clas X System quite relevant. The efficiency of high-quality gas combustion in this boiler reaches 93.6%. It is equipped with a two-speed pump and an LCD information display. In the appearance of the boiler, all the undoubted advantages of the Italian design school appear.
The best are used during production. construction materials , and special functions reduce the number of stops and starts of the boiler to a minimum. You can connect an external boiler to get stable hot water. As with the Cares model, the initial heat exchanger is made from high metallurgical grade aluminium. Depending on the specific subspecies, the gas combustion compartment can be either open or closed. Heat production for the heating circuit sometimes reaches 28, and for the plumbing - 31.8 kW.
Clas One is a double-circuit condensing boiler of the business category. According to the manufacturer, it is made with innovative additions. In particular, a specially developed heat exchanger of the latest generation, characterized by an increased diameter of pipes, was used. If street and apartment sensors are used, the system reaches efficiency group A+. The apparatus responsible for the suppression of working noises has been updated; storage tank for a mounted boiler with a power of 24 kW or other power must, for the most part, be purchased separately.
Connection
Knowing the wiring diagram for mounted Ariston boilers is very useful. Yes, the company prescribes that such work should be carried out exclusively by trained specialists. But they also need careful comprehensive control. The work is carried out in strict accordance with the instructions of SNiP. The prepared project is coordinated in the territorial bodies supervising gas safety.
The project must specify:
- what are the actual parameters of the equipment;
- where it will stand;
- how the rest of the heating infrastructure will be implemented.
Important: even if these conditions are met, the installation itself must be carried out only by representatives of authorized service centers. It is possible to use hinged gas boilers only when they are placed in separate rooms (furnace or boiler rooms). The exact list of requirements depends on the power of the boiler and the type of working compartment. In the case of an open chamber, the approach is approximately the same as when using a conventional furnace, that is, a chimney is used to remove gases. The window facing the street must have an area of at least 0.5 square meters. m, should also provide a sufficient area for maintenance.
Based practical experience, you can turn on the boiler without risk in the room:
- up to 8 cu. m (with a maximum furnace power of 30 kW);
- up to 13-14 cu. m (if they receive up to 60 kW of heat);
- from 15 m3 and above (if 60-200 kW is generated).
The approach to closed combustion chambers is different. It uses a coaxial type of chimney, that is, a double pipe. Outdoor air moves into the furnace through the outer part, and gaseous combustion products leave through the inner part. Such devices are in any case equipped with fans connected to electrical network. Exactly closed type the combustion compartment is optimal in sanitary and environmental terms, therefore it is recommended for kitchens and bathrooms.
The choice of the height of the wall mount and the method of such attachment is critical. Proper fasteners are not always added to the supplied bracket. Therefore, sometimes they are chosen individually, focusing on the material of the wall and its parameters. It must be taken into account that the bracket must transfer the load from the installed device and at the same time keep it in a level position. For floor systems requirements are noticeably softer.
The entire surface of the wall adjacent to the heat generator, even if located at a considerable distance from it, must be covered with a fireproof layer. The lower point of the suspended device rises 0.8 m above the floor, the distance from the wall to the rear line of the boiler is at least 50 mm. Next, connect the main heating circuit. How many pipes need to be connected depends on the one-pipe or two-pipe version of the system. Before connecting, we must not forget about the dismantling of the plugs covering the boiler pipes.
It is advisable to mount a filter on the input. Even if the filtration is provided in the boiler itself, it is still better to avoid overloading it. Only a boiler connected to the water supply can be connected to the gas supply circuit. Note: This information is for informational purposes only. Only professionally trained and authorized specialists are allowed to connect gas boilers to gas pipelines!
Initially, a valve is placed at the input to the device ball type. Before the device, a fuel consumption meter and a leak indicator are placed. Next comes the turn of the thermal alarm valve. If the temperature rises too high, it will block the flow of natural or liquefied gas farther. The next step is (for some boilers) connecting to the electrical network.
Most often, schemes are chosen that involve the use of three wires. Regardless of the scheme chosen, all wiring and devices connected to it must be grounded. It is very good when the boiler is connected to the mains through a voltage stabilizer. Having connected it to the electrical network, they are then engaged in the formation of an output to the chimney. Atmospheric boilers must have a separate channel for the discharge of combustion products.
At the time of installation, there should not be the slightest dirt and traces of soot or soot inside the chimney. The vertical block after the withdrawal from the device along the length to the nearest turn is equal to at least two diameters. Then begins the section where the pipe leans towards the boiler. It is recommended to reduce the length of the segment connected directly to the chimney as much as possible. Before filling the heater with water, a specialist is invited to personally set up the equipment and make sure that it works correctly.
An important role in piping a gas boiler is played by a thermostat. It simultaneously provides resource savings and an optimal level of comfort in the room (thanks to competent settings). Lowering the load of the boiler itself and the circulating pump also turns out to be quite profitable business. Even the most expensive device justifies the investment already for the first heating season. For your information: when it comes time to turn off the boiler at the end of this season, it is undesirable to drain the water.
Italian manufacturers have been producing Ariston brand boilers for quite a long time. Boilers became popular with us during the period of intensive individual construction buildings, in homes where work central system heating leaves much to be desired.
Ariston succeeded with his technical abilities, fell in love with the people due to the variety of configurations, a wide range systems and is still in demand among consumers.
The lineup
The line of models of double-circuit boilers, unlike single-circuit boilers, is more in demand, since the models are designed for heating rooms and supplying hot water.
BCS 24 FF (with closed combustion chamber) and Uno 24 FF (with open combustion chamber)
Most buyers choose Ariston of these brands. In addition to the operating instructions, all elements of the heating system are attached to the device, which you can manage every day and without special skills.
Efficiency reaches 95%, power - 24 - 26 kW, performance hot water– up to 14 liters per minute.
Genus
It is considered the most functional model. There is a display on the case, all the parameters of the device are reflected both inside and outside. Ariston of this brand is compact, equipped with a modulated burner that helps to save fuel, and there is also a programmer with a built-in timer.
You can set the program for the device immediately for a whole day, lower or increase the temperature, set the parameters for the unit at your discretion. The volume of the tank is 8 liters, the air vent is automatic, a self-diagnosis system is built in, all information is displayed on the display.
Egis Plus
Adapted for operation in the Russian climate. Models are not afraid of voltage drops in gas pressure in pipes. The unit has 2 heat exchangers: copper and stainless, also, a condensate collector for uninterrupted operation at outdoor temperatures below -52 degrees. On the panel - LED indexing.
All information can be read on the display.
Advantages and disadvantages
Like any system, the Aristons are not perfect.
Its undoubted advantages are:
- Safety. The system is safe, even though the fuel is explosive.
- Efficiency is high, when burned, the gas leaves practically no residues, the heating is completely spent on the needs of the owners, heat is retained in the room.
The disadvantages include:
- Don't choose a cat l for space heating
- For boiler installation requires a separate, and not small room, because next to it you still need to place fire fighting system, in case of fire
- The pressure in gas boilers is not stable, sharp jumps are possible, which is also explosive. Required additional installation adjustment unit, burners, the device can quickly fail.
Specifications and selection criteria
When choosing, it is important to pay attention to the following characteristics:
- Boiler power, consisting in the calculation of heat. Without certain knowledge, it is extremely difficult to do it yourself. The calculation takes into account the area of openings of all windows in the dwelling, the percentage of heat transfer from radiators, and the heat permeability of the walls. Only taking into account these parameters, the choice will be optimal, and you will not have to overpay for excess electricity. The average energy consumption coefficient is 100 W per 1 meter of housing. When combining a heated room with an unheated one, the indicator will increase by half, up to 160 V.
- The presence of a flue for gas outlet.
- The presence of a circular pump in Ariston. Without it, you can not leave the device unattended in winter, the pipes may burst. The control system should be simple and understandable to the average user. A device stuffed with various functions is unlikely to be needed for heating water, and the cost of such multifunctional blocks increases significantly. Today they are not in demand.
- Heat exchanger material. It is better if it is steel, cast iron, or copper. It is advantageous to have a copper unit, it has high efficiency, the entire temperature obtained is given to the carriers. However, the strength of copper is not different. Performance and durability are higher for cast iron boilers, the alloy is reliable and durable.
- The performance of the boiler depends on the water consumption for the needs of the family. The boiler is not suitable for heating large areas, but with the heating of water, he can handle it quite well. It is not difficult to calculate the water consumption, knowing that 5-6 liters of water flows out of the boiler per minute. Up to 12 liters pour out of the shower during the same time. It is necessary to count the number of points connected to the boiler and make a total calculation.
Manufacturers in the documentation for the boiler indicate the difference temperature regime before heating, compared with the temperature after heating. When choosing a model, in addition to the water flow rate, take into account the water temperature before starting to heat the boiler.
If up to 5 liters of water per minute flows out of the tap, the water temperature before heating should be at least 7-8 degrees. If there are 3 points in the apartment, you need 5 + 5 + 5 \u003d 15 liters. When the boiler is heated to 40 degrees minus 7 degrees, 33 degrees will come out before heating, which is quite acceptable both for washing kitchen utensils and for taking a shower.
The advantage of modern units is given to floor boilers. The operation of Ariston data is not affected by the quality of the power supply, models with cast iron heat exchanger more reliable and durable.
Price and reviews
You can buy a new Ariston for 20-25 thousand rubles. Foreign analogues, novelties with many functions and built-in LCD displays are more expensive, but they are also of better quality. Although our domestic producers nothing worse. It is better to overpay, but buy a reliable, trouble-free thing, taking into account all the described parameters.
Each owner of his house tries to make it as cozy and comfortable as possible. To achieve this, it is worth thinking about installing an Ariston double-circuit wall-mounted gas boiler, which will help solve problems with heating a dwelling. The device is very useful topics, which will provide heat both in an apartment and a private house up to 500 m².
Also, a gas wall-mounted boiler of a double-circuit type Ariston will allow you to quickly heat water for instant use. In this case, a person does not have to connect a boiler, which will require additional investments and separate place for installation.
Descriptions of the double-circuit boiler Ariston
Today on the market of gas boilers you can find a lot of interesting models. This is quite convenient, since everyone will be able to choose a device that is most suitable for the price, type, characteristics and installation method. Dual circuit wall boilers Aristons gained their popularity due to rare situations with their malfunction, as well as silence during operation, which is very important for maintaining a calm atmosphere in the house.
One of the most important components in all gas boilers is the burner, in this case it can be modulating or conventional. The first option is more popular than the second. When using it, the entire system will be regulated automatically, without human intervention. In this case, the power installed equipment for heating depends on temperature indicators.
The burner is also divided into 2 types:
- open;
It is the safest, since it does not involve the entry of combustion products into the room in case of emergency. Also in this case, the owner may not worry about building a chimney. To the closed burner it is necessary to bring a special coaxial pipe, it can always be brought out in any accessible place.
An open-type Ariston boiler, in any case, requires a chimney to bring combustion products outside. Also, do not forget about natural traction. Air will enter the system from the living quarters, so it will have to be constantly ventilated.
coaxial pipe used in closed system combustion, the good thing is that it is made of 2 layers. One is necessary for the withdrawal of combustion products, and the other will ensure the entry fresh air inside the boiler. Thus, the owner of the equipment does not have to constantly ventilate the room and worry about natural draft. The room will always have enough oxygen.
Distinctive abilities
According to reviews of gas wall-mounted double-circuit boilers Ariston, they have 4 distinctive features useful for their owners:
- All models of this company are equipped with automatic protection systems.
- The presence of a water pump, which is necessary for the constant circulation of water through the pipes.
- Possibility to choose a model with expansion tank. With its help inside the heating system will occur automatic adjustment pressure.
- Ariston equips its equipment with various types of ignition. It can be automatic, which will greatly facilitate the life of the owner of a particular boiler. Otherwise, each time the unit is started, a person will need to press a special button.
What are the advantages of Ariston gas boilers
Per recent times the popularity of the Ariston brand has increased significantly due to high-quality gas boilers, and this is not in vain. operates silently and consumes as little fuel as possible. This will allow the owners of the unit to save on utility bills and, at the same time, provide comfort and warmth to the house.
The client will receive a high-quality device that provides round-the-clock water supply and heating of the house, even with a large area of up to 500 square meters. Also, do not forget about the durability of the service of each boiler. The terms indicated in the guarantee are much more modest than they actually turn out to be. In terms of dimensions, the equipment is much more compact than other brands, which means that it can be installed absolutely anywhere, even in a small apartment with limited space.
Specifications
Almost all gas boilers from the Ariston brand have a capacity of 15 to 30 kW. Thus, each client will be able to choose the necessary indicators for the size of his apartment or house. Also worth noting are other distinctive characteristics such gas equipment:
- at maximum efficiency, boilers have high level efficiency factor;
- all wall-mounted boilers have Russian instructions and designations on the equipment itself, so citizens do not have problems with controlling the unit;
- most models from this manufacturer are able to perfectly cope with water in the system and low pressure;
- Special attention this equipment should be given to those people in whose houses voltage drops often occur. Ariston boilers can easily cope with such jumps in the network;
- All models are very easy to operate. To start using the boiler, you do not need to study the instructions for a long time, all the features of operation are intuitive and accessible even for those who install such a unit for the first time.
In some cases, the boiler cannot simultaneously heat water and provide sufficient space heating, this applies to budget models. In this case, a person needs to think about installing an additional boiler.
Note! If we talk about expensive units, they have a special display that shows different characteristics, including the temperature inside the boiler and outside. It is very convenient in terms of required characteristics for the correct operation of the equipment.
Operating instructions for gas boilers Ariston
Before purchasing an Ariston gas boiler, you need to understand that if the buyer does not understand its installation, it is better to contact experienced specialists and entrust all the work to them. After all, even at the maximum detailed instructions not the fact that the case will end successfully. In this case, there is every chance of damaging the equipment, after which you will have to call repairmen, and this will result in additional costs.
It is very important to keep children away from the equipment. For this, after, it is necessary to have a conversation with them and explain in plain language that nothing can be twisted and set on the unit, only an adult should do this. If the family leaves, for example, on vacation, after the boiler is turned off, it is also necessary to shut off all pipes for the supply of gas and water. Only after that the equipment is disconnected from the network.
If a display is provided on any model, all indicators that it displays must be strictly controlled. It may display problems that have occurred or deviations from normal operation occurring during the heating process.
One of the most important points in the instructions for gas equipment is safety equipment. Before connecting the boiler, you need to familiarize yourself with it first.
What are the types of wall-mounted boilers Ariston
All Ariston boilers are divided into 3 series. They have different technical indicators and functions, namely:
- Clas - this series refers to more bulky and powerful devices for heating residential premises. They are equipped exclusively with special regulators that automatically regulate the gas supply. This is necessary to save fuel, which is very convenient in terms of the cost of utilities and with frequent business trips of the owner of the house.
- Genus. These are the most innovative and multifunctional models gas units Ariston. They have more features than other boilers from this manufacturer. Along with the equipment itself, the buyer will receive additional accessories such as a fan required for smooth speed control, as well as heat exchangers, primary and secondary. All devices from the Genus line are distinguished by the presence of a large liquid crystal display. It will display all the characteristics that correspond to the operation of the boiler at the moment.
- Egis. Units from this series have small size and attractive appearance, which earned them great popularity among the owners small apartments. The device will fit well into any interior. Important feature of these boilers lies in the fact that, for their size, they have a fairly high level of efficiency and low fuel consumption, which is controlled intelligent system management.
Because of what the wall-mounted boiler may be faulty
The main reasons for the malfunction of Ariston gas boilers include the following:
- During the maintenance of the burner adjustment or control units, specialists made mistakes.
- Failed installation.
- Buying a fake, which is distinguished by low-quality components.
- Lack of sufficient air supply.
Conclusion
When buying one of the Ariston wall-mounted gas boilers from the seller, you need to check the availability of all necessary documentation, which
confirm that the equipment corresponds to the manufacturer. Only in this case, problems with the device will arise very soon.
