Infrared oven for sauna. Infrared emitters for saunas: how to choose equipment? Gas infrared sauna heater

Ecology of consumption. Homestead: Infrared sauna improves, stimulates and tones the activity of the whole organism, has a beneficial effect on the cardiovascular and musculoskeletal systems, and improves overall well-being.

To correctly understand what exactly we are talking about, you should remember the basics of what IR rays are.

Let's understand the terminology

Infrared is a type of electromagnetic radiation, described by optical laws. That is, the nature of IR radiation is similar to ordinary light. These rays in the spectrum occupy the range between visible (red), with L=0.74 μm (where L is the wavelength), on the one hand, and HF radio emission, L=(1-2) mm, on the other.

This region of the spectrum is divided into three groups:

• DW - Longwave (50.0≤L≤2000) µm;
• MW - Medium wave (2.5≤L≤50) µm;
• SW - shortwave (0.74≤L≤2.5) µm.

This radiation takes place in any heated body. Moreover, the higher the source temperature, the shorter L, and the more intense the IR radiation.

At low temperatures, almost the entire range of such radiation is in the infrared range. Visually, such a body looks dark. As the temperature rises, the wavelength emitted by the body shifts towards the visible spectrum, passing, successively, red, yellow and, when high temperature values ​​are reached, white.

On the one hand, this information is not related to the topic of this article, but on the other hand, it is directly related. It allows you to understand the terminological confusion that IR oven manufacturers allow themselves when describing their products:

• Some call it infrared;
• Others - longwave;
• Third - dark;
• Fourth - light.

But all of the listed ovens are infrared. And the discrepancy in the names is due to the fact that DWs have a lower temperature of the outer surface, so their IR radiation lies in the long-wave range. Such emitters are often referred to as dark ones, because. at such temperatures, the bodies practically do not glow. CB ovens are called gray. Their outside temperature is higher. And KV are characterized by max temperatures, and are called light, or white. In numbers it looks like this:

• Superdark bodies - (200≤t≤400)°С;
• Dark - (400≤t≤600)°С;
• Catalytic low temperature
• (600≤t≤800)°С;
• Medium temperature light - (800≤t≤1000)°С;
• High-temperature light - over 1000 ° C.

The design of the infrared oven

IR stoves for saunas are more correctly called heaters, since the principle of their operation is similar to heaters.

These devices have:

• metal or ceramic heat-resistant case of a rectangular shape, having the appropriate strength;
• an IR lamp is installed in it, similar to a fluorescent lamp (daylight);
• the case contains a heat-reflecting screen and a heat-insulating layer that protects the case from overheating;
• reflector that radiates heat;
• panel on which the heating elements are mounted.

When connected to the mains, the latter are heated. Heat is transferred to the reflector - emitter. The room warms up in stages. At first. Radiation zone. Then the air in the room. This ensures even heating.

In modern products, the following elements can be used as a heater:

• ceramic. A plate of ceramic material in which a high-resistance conductor is embedded:
• (nichrome), designed for heating up to a thousand degrees;
• Fechral (with very high resistance) - up to 800 ° C, respectively.

Due to specific design features, they are used only in ceiling and wall models. They are not used in floor-standing devices. Average service life - up to 4 years;

• Quartz. They are made from tubes made of quartz glass. They have insulation made of Al profile silt, which allows to achieve heat radiation from the entire surface of the plate at once. In many models there are several similar heaters.

Products are designed for seven years of operation;

• Carbon. A tube made of quartz, in which a carbon thread is embedded in the form of a spiral. The flask is vacuum. Carbon threads are heated up to 3000°C (while maintaining strength). The type of heating element determines the heating temperature of the reflector plate. Usually it is (200-600)°C. But max case heating temperature ≤ 60°C.
• Film emitters. They are fixed on the entire inner surface of the cabin (walls, ceiling). operating temperatures of the surface of such a radiator (25-50)°C. Often used in conjunction with ceramic.

The average dimensions of such a device: (1000-1500) * 160 * 40. Weight, depending on the model, (3.5 - 5.0) kg.

IR heaters are offered to the client in the following configuration:

• Complete heater;
• Fasteners included (this includes brackets, as well as hardware).

Everything else needs to be purchased separately:

• Automatic switches;
• Cable and plug matched to the existing load;
• thermostat;
• Other accessories.

Installation of IR ovens

Such heaters can be installed:

• On the floor. The downside is that they take up a lot of space. There is a high probability of overturning by negligence. Therefore, the devices must be equipped with an automatic shutdown if the heater falls;
• On the walls. Attaching is more difficult. But this is fully offset by the safety of this option, its compactness and visual appeal;
• On the ceiling. Requires the most complex installation and adjustment.

There are options for IR ovens designed for corner installation. They radiate in the (90-120)° sector.

To maintain the required temperature, special thermostats are used.

The zone of maximum efficiency of the heaters is approximately 150 mm from the body of the bather. With this in mind, the vertical wall-mounted installation option, in the immediate vicinity of the shelves, is considered optimal.

To warm up the legs at the level of the calf muscles, one or two heaters are installed.

Infrared chest heaters are mounted in the corners of the sauna cabin.

The optimal power for an infrared sauna is 350W (when located at a distance of 150 mm from the body). Higher capacity heaters are not recommended. At this distance, they can cause a burn. And at a greater distance, the efficiency of IR radiation decreases.

The surface of the installed emitters needs to be cooled. This explains the recommendation to leave 30-50 mm between their rear wall and the enclosing structure of the sauna cabin for the formation of convective flows. This allows you to cool the devices and reduces the warm-up time of the entire volume of air in the sauna cabin.

Furnaces are connected to a standard power supply network (230V/50Hz) at a current strength of 15A. a special socket for connecting the infrared sauna cabin is not required.

IR oven control

There are 2 control options:

• Provides temperature control. Turning the heaters on and off is carried out automatically according to the commands generated by the VCT sensor (temperature control). This option does not allow you to completely warm up the body of a person in the steam room;
• Designed to control power consumption. These models are designed to change the intensity of IR radiation, which allows you to select the indicator that is optimal for a particular person. In such a case, the entire human body is heated evenly, gradually and smoothly. What provides the maximum therapeutic effect.

To control IR ovens can be used:

• External control panel located outside the sauna cabin. Allows you to set the radiation power and duration of the procedure. After the set time has elapsed, the system disconnects from the network automatically;
• The built-in block of automatic equipment for regulation of work of all heating elements. With an average power consumption of 1.1 kW, this product is designed to control 6 IR heaters. Therefore, they are equipped with mini steam rooms, for one or two users. For larger saunas, a more powerful (1.5 kW) unit with 8 heaters is recommended;
• Internal remote control for adjusting the microclimate parameters to optimal values.

Advantages of IR ovens

Among the main advantages of such heaters for saunas, it should be noted:

• Their compactness, which makes it possible to complete them with even small apartment saunas;
• Simplicity and convenience of installation and dismantling;
• Autonomy. Such furnaces do not require constant human control and do not need periodic addition of fuel;
• Minimum warm-up time. The classic oven will heat the steam room to the desired temperature in 1.5 - 2 hours. IR oven requires ≤ 20 minutes. At the same time, oxygen is not burned out of the air;
• The low temperature of the case allows you to mount such heaters on surfaces finished with any materials;
• High economy. The choice in favor of IR ovens gives double savings:
• They are cheaper than classic electric furnaces;
• Consume 80% less electricity.

The choice of infrared saunas allows those who like to visit steam rooms to equip them even in their own apartment. published

If you have any questions on this topic, ask them to specialists and readers of our project.

At the moment, our company produces 350 W saunas and microcontroller control units, consisting of a power control unit for infrared saunas (BRM). Also, the set of equipment includes a wire for connecting PU and BRM.

The cost of the heater is 3000 rubles as part of a kit for self-construction of an infrared sauna.

When buying a ready-made kit for self-construction of an infrared sauna, the price of the emitter heater is 3,000 rubles, and the control unit is 8,300 rubles for kits Nos. 4-12.

By default, the standard dimensions of the front heater are 720 * 230 * 50 - the opening angle is 125 degrees.

Under your order, we can also produce a replacement for the failed one.

The cost of a control unit kit - a control panel, a power control unit, a connecting wire is only 9500 rubles in our .

The control panel allows you to adjust the power of the infrared radiation of the heaters in the range from 50 to 100% in 10% increments, organize a countdown of the session time from 99 minutes in 1 minute increments, as well as turn on/off the lighting in the infrared sauna. For more efficient and comfortable use of the infrared sauna, it also has a "HEAT" function to create the necessary microclimate in the sauna before taking a session.

At the request of the client, the color scheme of the facade of the console can be made to match the color of the tiles on the wall.

Do you want to build an infrared cabin or an infrared sauna yourself? You can purchase a ready-made kit. The set of equipment for self-construction of an infrared sauna consists of a selected number of infrared ceramic heaters and a control unit. Depending on the number of heaters, the sets are divided into No. 4 - 11 (according to the number of heaters for the convenience of the client).

If you have any difficulties with the location of the heaters or with the drawings of the future infrared sauna, then when buying a kit for an independent construction of an infrared sauna, we will make you a complete package of drawings for free.

We are the exclusive manufacturers of this equipment in Russia, so our prices are 5,000 rubles lower for each set than on sellers' websites Chinese equipment that pretend to be its manufacturers.

The cost of equipment kits for self-construction of an infrared sauna

At the request of the customer, it is possible to manufacture sets with any number of heaters. If you doubt the correct choice of the number of heaters - send us a plan of the room (you can "by hand", indicating the size and location of the door). After that, we will determine the most efficient location of heaters and their number. The production time for an order is usually 3 to 7 working days, depending on the number of heaters.

Infrared heaters for baths and saunas are an innovation in the modern world. This equipment is used not only for heating baths and saunas, but also for maintaining a positive temperature in warehouses, hangars and other premises. Next, we will talk about the advantages of an infrared heater compared to a sauna stove, as well as how to choose the right infrared heater for a bath and sauna.

The composition of the infrared heater

The infrared heater for sauna and bath has a fairly simple design, which has been modernized since 1965 (during this time, Dr. Tadashi Ishikawa developed this equipment).

The composition of the infrared heater for baths and saunas includes an infrared lamp with a power of up to 300V, a special reflector and a thermostat, which is often represented by a control panel. The lamp and the reflector are the emitter. This emitter is connected to the control panel using a heat-resistant silicone cable.

The advantage of an infrared heater for a bath and sauna

Despite the fact that many attendants try to maintain all existing traditions or, today in some cases it is advisable to abandon the classic sauna stove and use more modern equipment - infrared heaters for baths and saunas.

Among the advantages of an infrared heater are:

• Ease of installation / dismantling of equipment
• Compactness of heaters
• There is no need to prepare firewood and throw it up during the rest in the bath
• Infrared heaters are economical and consume 40-80% less electricity than an electric sauna stove
• Resting in a steam room with an infrared bath will not cause headaches, which can be caused by heating the steam room with an oven (pain occurs due to the burning of oxygen)
• Infrared heaters do not spread unpleasant odors (for example, fumes from burning wood or gas)
• The sauna stove heats the entire steam room completely, and with the help of a heater you can heat only the necessary area (for example, if you decide to take a steam bath alone)
• It will take at least 1.5 hours to heat the steam room with a sauna stove, while 20 minutes of its operation is enough to heat the steam room with an IR heater
• There will be no drafts during the operation of the IR heater
• Infrared equipment does not affect the humidity of the air, or rather, does not dry it
• The cost of an infrared heater for a bath is much less than the construction of a capital bath
• Can be used for heating

Despite this, infrared heaters also have disadvantages:

• The infrared heater is only suitable for small steam rooms suitable for relaxing with a small company.
• There are many contraindications for rest in the infrared steam room for people with various kinds of diseases.
• Infrared heaters do not fit into a traditional Russian bath
• On the stove for a bath, you can cure medicinal ones, which, when heated, stabilize pressure, clean the airways, etc. Infrared heaters are not used to heat stones.
• Despite its low cost, it will take about 4-6 devices to heat a small bath with infrared heaters, which together form a decent price.
• There is a high probability of purchasing a low-quality heater that can quickly fail.

How to choose the right IR heater?

First, before purchasing an IR heater, it is recommended that you familiarize yourself with the leaders in the production of this equipment and, if possible, give preference to them. Among domestic manufacturers, it is recommended to give preference to the companies Pion, Krona, Ecoline and General. Higher quality IR heaters are manufactured by the Italian companies AEG and ITM. German heater manufacturers are also renowned for the quality of their equipment (Kroll, Seibel Eltron and Eckerle). In addition, such firms as Energotech (Sweden), Noirot (France) and Nobo (Norway) have occupied a stable position in the market.

Secondly, it is necessary to take into account the power of infrared heaters. For sufficient heating of the body, it is necessary to use equipment with a power of about 350 watts.

Thirdly, pay attention to the size and shape of heaters. The larger the heater, the more space it will heat, while the effectiveness of its effect on the body will decrease. If you choose narrow small infrared heaters, they will direct all their heat only to a certain area of ​​​​the body.

Fourth, correctly calculate the number of heaters. For example, for a normal sauna experience, you will need about 6 pieces (4 will work on the back and 2 on the front).

Where and how should IR heaters be placed?

The zone of effective action of infrared heaters is about 15 cm from the human body. Based on this, it is recommended to install heaters vertically on the walls of the steam room next to the shelves.

Those heaters that will be directed to the chest of a person are recommended to be installed in the corners.

We draw your attention to the fact that the optimal power of heaters for baths and saunas should be about 350 W, despite the fact that they will be at a distance of 15 cm from the human body. It is not recommended to use more powerful heaters, because. they will inflict burns from a distance of 15 cm, and if they are moved further away, warming up the body will become less effective.

That's all you need to know about infrared sauna heaters! We draw your attention to the fact that if you have money, it is recommended to give preference to a traditional Russian stove for a bath, because. it will allow you to have the most qualitative rest with the company in your own steam room!

Bath procedures have always been considered very beneficial for health, which is why people tend to visit the bath as often as possible. In addition, it is also a good way to spend time in a pleasant company. Further in the article, we will talk about what kind of equipment is used for an infrared sauna, which is a modern version of a bath, in which infrared heaters are used instead of a stove.

Very often, modern steam rooms use gas or electric infrared equipment that emits waves that are safe for humans. Moreover, only 30 minutes spent in such a steam room can be equated to two hours in an ordinary Russian bath.

Advantages of infrared devices

Among the advantages of infrared sauna heaters are:

• compactness and the attractiveness of such devices allows them to be installed even in small rooms, for example, in mini-saunas of ordinary apartments.
• Convenience and ease of installation, that is, all the work can be done independently.
• Autonomy of work– you do not need to constantly monitor the operation of the appliance or add fuel, as is the case with a wood-burning stove.
• economy– Not only are infrared sauna heaters much cheaper than building a stove, but they also consume energy economically – 80% less than a stove.
• Warm-up rate rooms - to bring the air in the room to the desired temperature, such a heater in the sauna is capable of 20 minutes, and not 2 hours, like, say, a stove. In addition, the air in the room remains fresh, because the device does not burn oxygen.
• cold surface the body of the device allows you to mount it on any surface in the steam room - walls, ceiling, regardless of the material used.

Nevertheless, it is impossible not to mention some of the shortcomings of such devices. In particular, it is worth considering how many people the bath is designed for, since a rather large amount will have to be spent to heat large rooms.

When choosing the type of heating, you also need to keep in mind the overall design of the room, since cutting-edge equipment in a traditional Russian interior can look a little ridiculous. And, of course, you should not purchase devices of dubious quality, otherwise they will not stand the test of time.

Varieties of infrared heaters

All devices with infrared radiation by wavelength can be divided into three groups:

• shortwave;
• medium wave;
• longwave.

Equipment with shortwave radiation generates light fluxes of yellowish-red color in the range of 0.74-2.5 microns. It can heat up to 1000°C. Therefore, such equipment is advisable only in rooms with high ceilings of 8-9 m, in particular, in workshops or production and storage facilities. At the same time, it is impossible to stay under such waves for a long time.

Heaters with an average wave range of 2.5-5.6 microns are most often used to heat a certain area of ​​\u200b\u200bthe room. Their heating element reaches a temperature of 600 ° C. It is permissible to use such heaters in rooms with ceilings 3-6 meters high. It is advisable not to stay indoors with such devices for more than 8 hours.

In addition, the type of heater also depends on the size and purpose of the room in which it is planned to be installed.

Appliances with a high bracket are designed for installation on the floor and are most often used as an auxiliary heat source.

If the heater has an open heating element, then it is intended for mounting on the ceiling in high rooms. The kit includes all the necessary fasteners for fixing the device.

IR emitters for a sauna with a closed heating element should be used in rooms with a ceiling height of 2-10 meters. In addition, such products organically fit into the interior of the sauna.

For installation above windows or doorways, special moldings are commercially available that provide a thermal barrier and prevent the penetration of drafts.

For small rooms with ceilings up to 3 m high, cassette-type heaters are provided, which can be mounted directly to the suspended ceiling frame.

Another type of heaters for a bath is able to work on hot water. As a rule, such equipment is hidden in the false ceiling structure.

Note that any equipment with infrared radiation must be equipped with a thermostat so that you can control the degree of heating of the room.

How an IR Sauna Heater Looks and Works

Externally, such a heater looks like a rectangular metal case, with an infrared sauna lamp inserted into it, somewhat reminiscent of a fluorescent lamp. Inside the case there is a screen that reflects heat waves, a heat-insulating layer so that the case does not heat up, a reflector that radiates heat, and a panel with a heating element.

As soon as the device is connected to the network, the heating elements begin to glow, transferring heat to the aluminum reflector that emits waves. In this case, objects in the radiation zone are heated, which in turn give off heat into the air. So the room warms up evenly.

Heating components are of the following types:

• Ceramic elements- are a ceramic plate with a high-resistance conductor built into it. It is made of nichrome, which can heat up to 1000 ° C, or fechral, ​​which, having a high electrical resistance, heats up to 800 ° C. As a rule, the service life of such a heater is 4 years.
• Tubular heaters with aluminum profile insulation. This design allows heat to be radiated along the entire length of the plate. Often, several such heating elements are installed simultaneously in IR heaters. The service life of the equipment is about 7 years.
• Carbon heating element is a quartz tube with a built-in carbon spiral thread. The flask is completely sealed and devoid of air. The carbon thread is able to heat up to 3000 ° C without losing strength. Therefore, such equipment can be used for a very long time if it is of high quality.

The reflector plate, depending on the type of element, can be heated up to 250-600 °C, but the body itself does not get hotter than 60 °C.

The overall dimensions of such a device are 16 cm wide, 4 cm thick, 1-1.5 m long and 3.5-5 kg ​​in weight.

Usually, the infrared sauna kit includes the heater itself, as well as fasteners - hardware, brackets, dowels and self-tapping screws. But a thermostat, a cable with a plug, a cross section designed for the expected load, automatic electricity switches and other components must be purchased additionally.

If everything is connected correctly, the equipment can work for about 25 years.

Principles for choosing an infrared heater in a bath

When choosing equipment for a sauna, you should pay attention to such parameters as:

• dimensions;
• wavelength and power;
• company manufacturer;
• case cover;
• installation type.

Manufacturers of infrared equipment

Perhaps the highest quality IR devices are produced in Russia. Among the most famous representatives producing reliable and durable products are Peony, Ecoline, Master Hit, Ballu. Their range allows you to choose the right device with any parameters.

Italian products are represented by ITM and AEG brands. All of their heaters are equipped with moisture-resistant housings that are not subject to mechanical wear.

The German companies WAGO, Eckerle and Kroll produce heaters with economical energy consumption. At the same time, such equipment differs in high power and excellent quality.

Also on the market are IR heaters from French companies. In particular, the Thermor company presented models that, despite their small size, are quite capable of replacing the main source of heating. Another brand "Noirot" is distinguished by its high heating rate, compact size and safety.

In addition, you can purchase an infrared sauna heater made in Switzerland, which is reliable in operation and attractive in appearance, as well as products from companies from Turkey, Denmark, Greece or Sweden.

Thanks to such an extensive range, you are guaranteed to be able to find the most suitable sauna equipment for yourself.

Ways to install IR heaters

The simplest and most convenient installation is floor-type infrared heaters. However, they take up a lot of space and can be accidentally knocked over by children, for example. Therefore, in units of this type, there should be an automatic shutdown function in the event of a fall.

Wall-mounted infrared heaters are somewhat more difficult to mount, however, this disadvantage is compensated by their compactness, safety and organic appearance.

The most difficult thing is to install ceiling structures that are able to evenly distribute heat waves throughout the room.

Very often they buy an infrared sauna stove, which can be built into the corner of the steam room. As a rule, such devices can be opened by 90° or 120°.

To maintain the temperature in the steam room at a certain level for a long time, you can install a thermostat with a rotary mechanism, which is preferable for use in saunas.

Purchase hardware requirements

When purchasing an IR heater, it is worth checking the following points:

• the integrity of the packaging, the presence of protective overlays on the case;
• checking the device for operability - the seller has no right to refuse;
• noiseless operation of the unit - if there are extraneous sounds, then it is better not to buy this device;
• providing a warranty card and a receipt for the purchase;
• the seller has quality certificates for the goods.

If one or more of the above conditions are not met, you should refuse to purchase goods in this store.

To make the operation of infrared heaters as pleasant as possible, you should pay attention to some recommendations:

1. It is better to install the equipment vertically, because a person mostly sits in the sauna. At the same time, several devices must create a single heat flow, that is, they need to be placed on the back wall, on the sides, above the door and in the riser of the bench.
2. The larger the room, the higher the power of the device is needed, since it must heat all surfaces, objects and people in the room.
3. The efficiency of the equipment is determined by the emissivity, that is, with a value in
   80%, only 20% of the energy will be wasted.
4. The height of the ceiling also affects the power of the device, since weak devices will not be able to generate waves of such strength that they can reach the floor in a room with a high ceiling.
5. The reverse situation will be observed if a heavy-duty device is placed in a low sauna, since it will not be comfortable to be in it due to excessive radiation.

Film-type infrared heaters

To equip an additional source of heating, it is advisable to use infrared film. A layer of carbon paste of 1 micron is applied on it and carbon threads are glued. The insulation of the film is made of polyester, permitted by electrical insulation and fire regulations. The radiation range of the film is 5-20 µm, and the heating intensity is from 30° to 110°.

Such a film can be laid absolutely under any coating, including under ceramics or stone. Although in the latter case, installation should be carried out by specialists.

Thanks to the decorative lamination, the infrared film can be mounted on the ceiling or walls.

The kit with thermal film includes a thermostat and a cable with a plug. The service life of such devices can be more than 20 years if the product is really of high quality and is used from time to time.

Flat IR devices

As a rule, infrared panels are designed for intensive use, therefore they are mounted under the bench, above the entrance, on the side and rear walls of the steam room.

The IR heating panel with a mirror coating looks especially beautiful. It is very convenient, because it also performs the main function - heating, and is a mirror that gives the room a visual depth. And neon lighting will make the interior almost cosmic.

What are reflectors

Reflectors in IR heaters are used to spray heat waves to heat as many objects as possible.

Wide reflectors are designed for small spaces, as they reflect waves at an angle of 120 ° so that they do not cause discomfort to a person.

In large saunas, on the contrary, corner models are often installed that focus the radiation on the benches at an angle of 90 °.

How to control the heater

Depending on the type of control, infrared heaters are available in two versions:

1. With adjustable temperature. This method involves periodically turning off the heating when a certain air temperature is reached and turning it on as the room cools down. In this case, it is impossible to achieve complete warming up of the human body, because the device turns off every now and then.
2. With power regulation. Heaters of this type can change the intensity of radiation, so that you can choose the optimal indicator for a person. With this approach, there is a smooth, gradual and deep heating of the entire human body, so that the effect is very beneficial.

Power control is carried out using the following elements of the system:

• Control panel located outside the cab. The duration of the procedure and the power of the waves are entered into it. The program allows you to set the procedure time after which the device will disconnect the system from the network. The remote control can control the operation of two power control units.
• The operation of the heating elements is regulated by a special unit. With a power of 1.1 W, it is able to manage 6 heaters, so it is often used in mini-steam rooms for 1-2 people. For large saunas, it is better to use a 1.5 kilowatt unit capable of controlling 8 heaters.
• An internal remote control is installed in the cabin itself, which allows you to adjust the microclimate to comfortable levels.

Additional features of infrared heaters include smooth heating, which prevents sudden power surges, as well as a “time counter”, relevant for commercial establishments, which automatically turns off the current after a specified time.

In general, we can say that infrared heaters meet all safety standards, they are quiet in operation and provide gentle gentle heating of the body, which contributes to maximum relaxation. In addition, the ratio of price and quality of these devices is one of the best among all other options.

Increasingly, owners of country houses are abandoning traditional stove heating and choosing heating appliances. This is due to the fact that stove heating requires the preparation of firewood before winter, and is also associated with some difficulties. For example, for heating with wood, it is necessary to equip a woodshed and constantly carry firewood into the house during heating. If a country house or a bathhouse is used only once a week or even less often, it is easier to purchase a heater.

How to choose

Before choosing a device for heating a summer house in winter, it is necessary to consider several types of such devices and determine which one is suitable for a particular house. There are many models that will provide the house with hot water.

Most sauna heaters are powered by electricity. They are purchased quite often, which is due to the ease of use of the device. Increasingly, owners of suburban areas are purchasing infrared heaters. To decide on the purchase of such a device, it is necessary to consider the advantages and disadvantages of these designs.

Features of infrared devices

The advantages of infrared heaters include:

• ease of installation;
• the compactness of such equipment;
• no need for firewood;
• lower energy costs compared to electric furnaces;
• after relaxing in a steam room with infrared heaters, headaches do not appear, which usually accompany pastime in a standard steam room;
• the absence of unpleasant odors that spread wood stoves;
• the possibility of heating a certain zone in the room;
• steam room heating rate.

It is worth noting that the cost of infrared devices for a bath is lower than the price of building a wood-burning stove. Infrared heaters also have disadvantages. These include the presence of contraindications. Before installing such devices, you need to learn more about diseases in the presence of which you should not use them.

Another disadvantage is the appearance of infrared heaters, as they do not fit into the interior of a Russian bath. To heat the entire steam room, you need to purchase several heaters, so the cost of bath equipment is quite high. To purchase high-quality infrared heaters, it is worth considering the rating of devices compiled by consumers.

The most common heater models

One of the most popular infrared sauna devices is the UFO Alf 3000. It looks like a small rectangle, the dimensions of which are 190x1080x90 mm. Such an infrared heater is capable of heating a room up to 30 square meters. It should be noted that warming up takes about 3 hours. The power of the heating element in the device is 3 kV/h. It can be mounted on the included legs or hung on the wall.

Also a popular device for a bath is a model called "ENSA P900G". Such infrared heaters are designed for small areas and are able to heat the air in an area of ​​18 square meters. The peculiarity of this device is that first it heats the objects, after which the heat is released to the air. It is worth noting that this heater maintains the level of humidity in the room. Such a product is able to raise the temperature to about 24 degrees in just 2 hours.

"UFO ECO 1800" is another heating device that can be attributed to the most popular. The small size of this product allows you to install it almost anywhere. This heater can work even in the open air due to an autonomous source of electricity.

Often, owners of country houses purchase infrared heaters for a bath called "ENSA P750T". The peculiarity of this heater is that its body does not heat up during use. Such infrared devices are used to heat rooms, the size of which is approximately 14 square meters. They are almost invisible and can be mounted on legs and fixed on the wall.

The UFO LINE 1800 model is also often purchased. It has the following advantages:

• reliability;
• small sizes;
• efficiency;
• economy.

For 2 hours in winter, this device for a bath is able to warm up a room of up to 18 square meters. Another feature of this heater is that it can be installed on special legs, mounted on the wall and ceiling, and also used outdoors.

The best infrared heaters

In order not to make a mistake when choosing an infrared heating device for a summer residence, it is worth considering the most popular models that are rated by customers as the best. These include the following infrared devices:

Conclusion

All presented models of devices are suitable for giving and can serve as the main source of heating.