Rules for connecting a heated towel rail, expert advice. How to install a heated towel rail in the bathroom yourself How to hang a heated towel rail in the bathroom

The need for a heated towel rail in the bathroom is probably not worth discussing - this device is definitely useful, and it takes up little space. Usually the bathroom already has such a device, but sooner or later it requires replacement - and here we get the opportunity to install a much better device.

What types of heated towel rails are there and how to attach them correctly - we’ll figure it out.

Choosing a heated towel rail

Type 2. Water heated towel rails

Typical bathrooms typically use pipe drains to dry towels and wet laundry. hot water or a separate circuit powered from (less commonly). Also, instead of such compromise solutions, a special tubular coil can be used, but in any case, the principle of operation of the device remains unchanged. The coolant circulating inside the device transfers its temperature to its walls, which in turn ensure effective drying of towels.

The main difference between the models is their configuration, as well as what material the dryer pipes are made of:

Illustration	Material
	Stainless steel. Pros- products are inexpensive, and therefore they are produced in large quantities and a wide range. In addition, steel pipes withstand mechanical loads well. Cons- steel, even coated protective compounds, will be susceptible to corrosion in a humid environment. In addition to this, upon contact with hard tap water Scale forms inside the heated towel rail. Salt deposits on the walls not only increase hydraulic resistance, but also reduces heat transfer.
	Black coated metal. Instead of stainless steel, heated towel rails can be made from ordinary steel with an anti-corrosion coating. The pros and cons of this type of product are similar to those described in the previous column of the table. As for the coating, it can be metal (most often chrome or chromium-nickel) or enamel. The first is stronger, but less resistant to corrosion. Enamel, on the contrary, is practically not susceptible to chemical influences, but when struck it can affect the base.
	Non-ferrous metals. Making a water heated towel rail from copper or brass solves the main problem - corrosion. These materials do not rust, and the patina on the copper surface acts as a kind of insulator that prevents oxidation. Additional plus- attractive appearance of these metals. Cons: electrochemical corrosion at the junction of copper pipes with pipes made of stainless steel or other metal; damage to the internal surface of the heated towel rail by suspended abrasive particles, causing the accumulation of salts; high (from 3 thousand rubles and more) price.

In addition, installing a heated towel rail of this type is quite a labor-intensive undertaking. The complexity depends on the device design, connection method and a number of other parameters. Therefore, you should take on work only after careful preparation!

Type 1. Electric models

In the bathroom small size, as well as in a room in which there are no leads for a heated towel rail, you can install electrical device. The advantages of such heated towel rails are their compact size, sufficient efficiency and variety of shapes. There is essentially only one drawback - high energy consumption.

Electrical device design:

Frame. The heated towel rail itself is a “ladder”, “coil” or other multi-sectional device, which is made of steel or a light alloy with an anti-corrosion coating.

Heater. Inside the case there is heating element, more often tubular type. The heater power ranges from 300–400 to 1500 W or more.

The most powerful heaters are used in large bathrooms, as well as in hotel bathrooms and. For standard apartment 400 W is quite enough.

Control. Electric heated towel rails are usually equipped with a power regulator. This allows you to select the heating temperature of the working surfaces. You need to dry the towel quickly - turn it on to maximum, and if you don’t need to rush, set it to low heat and save electricity.

Power supply. There are two options here - a permanent connection to the network (hidden or open) or connection to an outlet. The second option is preferable, but it is extremely important that the outlet is waterproof. In a bathroom, the probability of water drops getting on the body is close to 100%, so it’s better to be safe in advance.

The result is a fairly effective device, which is installed with minimal labor costs. That's why, if there is an outlet in the bathroom, then choosing an electric heated towel rail will be completely justified.

Installation technology

Option 1. Installation and connection of the water system

So, let's figure out how to install a towel dryer with your own hands. Let's start with more complex option- water device.

For work we will need:

The heated towel rail itself.
Angle or straight fittings.

A universal option for connecting such products is “American”. They are both reliable and easy to use.

Ball valves.
Plumbing tape for sealing connections.
Fasteners for fixing the structure to the wall.

Tool set:

Grinder with a metal disc (for dismantling an old pipe).
Hammer or drill with drills for tiles/concrete.
Adjustable wrench.
Key for tightening “American women”.

Screwdriver.
Measuring tools.

The system is installed according to the following scheme:

Illustration	Work stage
	Preparation of communications. To connect the heated towel rail, we prepare outlets from the hot water riser. This can be either an existing pipe or a newly laid one. In the first case, we need to cut off the old heated towel rail, align the ends of the pipes and cut threads on them. In the second case, we lay the pipes the way we need. It is also possible to install communications under the cladding with an outlet into the plane of the wall under a corner fitting.
	Installation of taps. It is advisable to install on the terminals for connecting the heated towel rail ball valves. Their installation allows you to disconnect this part of the circuit from the network for replacement or repair. It is also advisable to integrate a “bypass” into the system - a jumper between the input and output of the heated towel rail. The bypass can be a section of pipe from which the pipes for connecting the device are diverted.
	Installing the mount on the coil. We install fastenings on the heated towel rail itself for fixing it on the wall. As a rule, such fasteners are simply put on the pipe and tightened with a screwdriver in the right places.
	Installation of "American women". Using plumbing winding and sealant paste, we install “American” fittings at the outlets of the tubular part of the coil. We tighten the union nuts tightly, but not too much - so as not to deform the product or break the thread.
	The tightening of the “American women”. We tighten the internal parts of the American women with a special wrench. This will allow the connection to be as tight as possible.
	Mark on the wall. We attach the heated towel rail to the terminals, tighten the threads and mark where the mounting plates will be located. Through the grooves for fixing, we use a marker to make marks on the wall for drilling.
	Drill holes for fasteners. First we go through the tiles with a special drill, so we go deeper into the wall using a concrete drill. We hammer plastic dowels into the holes. Usually some kind of fastener is included with the coil, but it is better to throw it away and use 6x40 mm dowels for express installation.
	Fixing the heated towel rail. We return the product to its place and fix it on the wall. To do this, we fix the support plates with locking screws, inserting them into the dowels and tightening them with a screwdriver. After this, we rotate the adjusting screws on the fasteners, selecting their length so that the device becomes strictly parallel to the wall.
	Tightening fasteners. Nuts in the place where the heated towel rail is attached to the terminals with hot water tighten using adjustable wrench. Here, too, it is important not to overtighten the connection.
	System check. We open the taps at the inlet and outlet and check how the system works. There are only two criteria for the success of our work: Connections do not leak. The surface of the coil heats up.

Of course it's not the only way. It is quite popular to attach a heated towel rail to corner fittings with bottom connection, or installation through an open bypass. In any case, you need to choose an installation scheme based on the conditions and model of the device.

Option 2. Installing an electrical appliance

One of the advantages of electric models is that easy installation. For installation we will need:

Hammer or drill with appropriate drill bit.
Level.
Phillips screwdriver.
Connection Tools electrical wires(when installed without a socket).

Electrical Device Installation Instructions:

Illustration	Work stage
	Preparing the device. We unpack the heated towel rail by removing it from the box and unrolling the connection cord. Skip if necessary electrical cable through the holes in the mounting strips.
	Installation of fasteners. We install mounting panels or legs on the back of the device. We fix them with fastening screws, tightening the parts with a Phillips screwdriver.
	Marking for drilling. We apply the product to the wall, level it and apply markings for drilling mounting holes. We apply masking tape along the markings, which will prevent damage to the finish when drilling.
	Preparing mounting holes. Using the markings, we drill holes, the diameter and depth of which correspond to the fasteners used. We insert plastic dowels into the holes. We drive them flush with the wall.
	Fixing the heated towel rail on the wall. We apply the device to the wall, level it and fix it by screwing the locking screws into the dowels.
	Laying hidden wiring. When connecting to an outlet, simply pull the cord where you need it. For a hidden connection, we connect the wires from the heated towel rail with the wires coming out of the wall. We carefully isolate the contact point and hide the wiring either under the casing or in decorative strip devices.
	Fastening decorative overlays. We put decorative overlays on the mounting strips and fix them with self-tapping screws or self-tapping screws.

After installation, apply voltage and check the degree of heating drying elements. We also control the operation of the thermostat by selecting optimal mode work.

As with the water model, there may be variations here too. But the field for experimentation is limited, essentially, by two points:

Form of fastening (legs or plates).
Type of connection (hidden or through a socket).

But in general, the “drilled to the wall - connected to the power wires” scheme remains unchanged.

Conclusion

When choosing the type of fastening for a heated towel rail, you need to take into account its design, installation location, and method of connection to communications. No particular difficulties are foreseen here, but beginners will find the above instructions very useful and visual video in this article. In addition, in the comments you can get an answer to your question.

There is a heated towel rail in every bathroom.

Installing a heated towel rail is not challenging task, which every man who has no experience in this matter can handle.

We will tell you how you can do this yourself.

You won't have to turn to professional plumbers for help if you read this article.

Preparatory stage

What you need to do first is decide on the design.

It should not only be comfortable, but also beautiful, and also choose the mounting method and select the optimal size hollow products for the battery.

It is required for:

drying small personal items,
reducing the percentage of humidity,
reducing dampness in the room,
creating a certain microclimate.

At the moment, models of heated towel rails in the shape of the letters “P” and “M” are in particular demand among ordinary people.

But despite such preferences our compatriots, on the market in wide range, there are samples in the shape of a “ladder” and corner specimens.

It's no secret that each product has its own characteristic features, mounting options and cost.

When choosing the product you need, you need to consider large number various factors.

Not always your favorite model may be ideal for installation in your bathroom (read about premium bathroom partitions in the article).

Most important point - these are the dimensions of the room and, of course, the diameter of the pipes.

For small bath It is best to buy M-shaped and U-shaped dryers.

In large and spacious rooms Telescopic, rotating samples and “ladders” will look more advantageous.

Products can be quite impressive in size or very small. I would especially like to note the corner structures.

Despite their compact size, they look very impressive. In addition, these devices perform the functions assigned to them “excellently”.

We will not talk for long about beauty and attractiveness appearance various heated towel rails, and we will pay more attention to the fastening elements with which they are installed.

Fittings (about crimp high pressure written) play an important role in creating the aesthetic appearance of the entire structure.

Pipes hidden in the wall look especially nice, while all fasteners (including fittings) are also hidden.

However, this type of installation is considered complex and is used very rarely. More often, heated towel rails are attached to external pipes. In this situation, the fasteners are open.

What fasteners are needed

If you decide to replace a towel dryer in your bathroom, you need to take a responsible approach not only to the choice of material from which the product is made, but also to the fastening elements.

Since the beauty, functionality of the design, and the overall practicality of the entire drying system as a whole will largely depend on this.

Perhaps those who are faced with assembling a device for the first time do not quite understand what fittings are.

Information for the uninformed public:

fittings are small parts (most often chrome-plated), which are very difficult to do without during assembly.

The choice of fastening components should exactly match the design you like and the material from which it is made heating device.

The optimal option is when the entire device is made of the same material.

Types of fittings

Sectional extension cord.
A representative of this category will help you, if necessary, adjust the distance from the heating device to the wall to which it will be attached.
These fittings act as a kind of bracket, the connection of which requires at least several fasteners.

Extended collapsible fittings are connected only in front of the pipe bends.

This modification of connectors has one minor flaw - they have too long threads.

However, this problem can be quickly resolved (threaded fittings for copper pipes are described in the article).
How?

Excess grooves can be quickly and easily removed (cut off or sharpened).
Rewinding made of polymer materials.
This type of fitting eliminates the possibility of play at the adjusting connections.
If the winding is done correctly, it will take the look you want.

It is also worth taking into account the following fact: the above-mentioned part will not compact over time.
Angle tap.
It is used to connect a tubular radiator directly to a central heating pipe.
Depending on the size of the hollow products used, you can use either standard modifications of the corners or choose the option that you find more convenient.

With the help of corner fittings, you can change the direction of the pipes at your discretion.
Tee.
This simple connecting element will be very useful to you if you need to make a number of branches from the central highway in different directions.
Using this fitting, you can directly connect the heating device and the riser.

At the same time, do not forget to install a bypass.

The bypass line will allow you to turn off the heated towel rail for a while, without creating any obstacles to the operation of other heating devices.
Cross fittings.
With their help, the system is branched along only two different courses.
American fitting.
If you need to dismantle the structure, this can be done using a kind of crane called an “American”.
It is very difficult to overestimate the ease of use of this fastener - you will not need to completely disable the system.

It is enough just to close this device, unscrew the nut and remove the heating device.
Connections in this case come in several types:
- nut - fitting,
- nut - nut,
- fitting - fitting.
Clamping device.
Implements similar functions as the “American” one.
Thanks to this coupling, you can quickly disassemble and reassemble any connection.
This part has one feature - it has different sides various diameters.

This property is used when there is a need to join pipes various sizes. The thread of the clamping ring can be either external or internal.
Reflectors.
These fittings do not allow moisture to seep into the fastening (read how to fix a leak in a pipe with water).
Limiters.
They are used to seal pipes

When purchasing chrome plated fasteners for tubular radiators, you need special attention pay attention to the quality of the thread.

ABOUT high quality products can be judged by the uniformity of the grooves.

Another feature of non-chrome-plated connections is that they quickly undergo the rusting process.

Your best decision will be to purchase a heating device along with fittings.

This way, you will save yourself from searching for the parts you need or exchanging existing but incorrectly sized parts.

Step-by-step installation instructions

Since the heated towel rail is mounted directly into the water supply system, it is very important to ensure that the device functions correctly.

If you make mistakes in your work, then not only the drying itself, but also the plumbing system may suffer.

In general, the installation process is not difficult. And it consists of the following: we supply water to one side of the device, and ensure its outflow from the other end.

That's it, the work is finished. Are you wondering how much all this will cost?
It makes no sense to talk about specific numbers.

Much depends on the complexity of the work being performed, the type of coil chosen, etc.

Please note the maximum distances between the wall and the heating device, which must be observed:

5-7 centimeters - if the diameter of the pipes is more than 2.5 centimeters
3.5-4 centimeters - for pipe cross-sections less than 2.5 centimeters.

In order to avoid subjecting the walls to heavy loads that can be caused by hot thermal deformation, the structure cannot be fixed rigidly.

The coil is hung on mounting brackets.

After completing all work, you need to check all connections for leaks. If a leak is discovered, it must be repaired immediately.

Highlights

The system may only use components that are made of the same metal.
Otherwise, electrolytic corrosion will inevitably occur.

To prevent this from happening, only Teflon gaskets are used to seal connections.
If you want the heated towel rail to work all year round, it must be connected to the hot water supply system.
When connecting a ladder type model, it is better to use the side connection method.
In this case, it is necessary to maintain an interaxial distance of 50 cm.
Would you like to connect a heating device? to the heating system?
A combined model is suitable for these purposes.

Worth knowing! The device must be connected to the riser using “American wires”.

Important point! When carrying out installation work, all docking units must be carefully insulated. If you decide to “burrow” the pipe into the wall, it will be incredibly difficult to fix leaks later.

Watch the video to see how to install a heated towel rail in a new building with your own hands.

From the author: Hello, dear friends! At major renovation In the bathroom, many are interested in the question of how to install a heated towel rail step by step with all the fittings. And it is not surprising, because this equipment provides many functions.

With its help, the room is maintained comfortable temperature and normal humidity levels. It is also very convenient to dry things on it: for example, wet towel, or many small children's things that need washing so often.

In addition, in lately The heated towel rail is also an important design element. Many people cannot remember without a shudder those bulky, crude structures that were located in old-style apartments. The only way to fit them into the design of the room was by painting, but even this procedure did not greatly improve the appearance of this equipment.

Now the market offers us a great variety of options, and almost all of them differ, at a minimum, in aesthetics. That is why replacing a heated towel rail is one of the main stages of work in the bathroom.

Frankly speaking, the installation procedure is not one of the simplest. Therefore, many people prefer to invite a specialist to perform it. On the other hand, during repair work The issue of saving is more pressing than ever.

To save a significant amount of money, you can do everything yourself. To do this, it is enough to have at least the slightest experience in plumbing work, as well as accuracy and attentiveness.

In today’s article I will talk in detail about how to install a heated towel rail in the bathroom yourself according to all the rules. Even if after this you decide not to get involved with this matter, but to call a specialist, you will be able to at least consciously monitor his actions, which is also important.

Types of heated towel rails

I propose to begin by structuring a little in your head the diversity that offers us modern market. Heated towel rails can be in the form of a snake and a ladder, with or without hanging bars - there are many options for appearance, you can choose from them the one that best suits your taste and the needs of the whole family.

But according to the type of connection, this equipment is divided into only three types:

electric. Essentially, this is an ordinary heater that hangs on the wall. It does not require any installation procedure. The entire installation consists of fixing the fasteners on the wall, hanging the heater on them and plugging it into the outlet. The only thing you should pay attention to increased attention- this is safety. Still electrical appliance in conditions of high humidity is always a source of risk to life and health. Therefore, it is necessary to monitor the serviceability of the device, and also initially make sure that there is grounding or do it yourself. Detailed information You can find information about this procedure in other articles on our portal;

water. Such a device is connected to hot water supply pipes, due to which it is heated. For many people, installation of such equipment is real problem, therefore, in today’s article we will talk about him;
combined. Such equipment can be powered either from a water supply or from electrical network. But its connection to hot water pipes occurs in exactly the same way as with water varieties, so consider combined variety separately does not make sense.

The fittings are no less varied. Simply put, these are various fasteners that serve to fix the heated towel rail to the wall, while performing some additional functions.

For example, there are the following types details:

selection extensions - help change the distance between the equipment and the wall;
polymer winding - makes it possible to avoid the appearance of play in the places of adjustment joints;
tee - necessary for forming branches;
corner tap - using it tubular radiator connects to central heating;
“American” - this fitting greatly simplifies the procedure for dismantling equipment.

This is far from full list varieties. To avoid getting confused, it is best to purchase a heated towel rail in a complete set, which includes all the fittings necessary for a particular case.

Operating principle

Now let's figure out how a heated towel rail works. At first glance, its device is absolutely simple: a pipe through which hot water runs. But for some reason, in many cases, after connecting it, a lot of problems arise.

For example, if we are talking about equipment in the form of a ladder, then some rungs warm up more than others, which should not be the case. And there are cases when, as a result of installing a heated towel rail, the operation of the hydraulic system is completely disrupted, and everything has to be redone, simultaneously quarreling with neighbors who are freezing in theirs.

All this happens because when installing such seemingly simple equipment, it is necessary to take into account many nuances. There are several proven connection schemes that eliminate the risk of such situations. Let's look at each of them in detail.

Coil connection

In this section we will talk about a heated towel rail made in the shape of a snake. These are the ones that were previously installed in homes everywhere. Accordingly, it is easiest to replace an old device with a new one that has the same configuration.

Installation of such equipment is carried out in several stages. The first step is to shut off the riser and drain the water from it. If you live in apartment building, then specialists from the housing office will deal with this issue. To do this, you must first write an application to turn off the riser.

After the riser is ready for use, the old heated towel rail must be dismantled. Sometimes it is simply cut off using a grinder. Then new equipment is installed in its place.

In general, in such conditions the best option is to replace not only the heated towel rail, but also the riser. If you change it to an option made of polypropylene, you can immediately weld the necessary fittings to it, which will ensure the possibility of switching to threads and, accordingly, ease of installation of the equipment.

The main thing during such work is to ensure that the required diameter is available. The pipes should not be smaller than the previous ones, otherwise this is fraught with serious problems in hydraulic system. After installation, the new or old riser can be disguised using decorative box. The heated towel rail itself, as well as its connection points to the main pipe, remain visible.

Even with such a simple installation procedure, mistakes are often made. The first of them is the use of press fittings with subsequent narrowing of the internal diameter of the pipe. In this case, the hydraulic resistance, of course, becomes higher, which is why the performance of the riser sharply decreases.

The second mistake is installing shut-off valves in front of the heated towel rail. In general, these devices are necessary, because with their help, if necessary, you can turn off the equipment for repair or dismantling.

But in the case of a coil, the valves installed on it will shut off not only the heated towel rail, but also the entire riser. In this case, your neighbors are unlikely to thank you, since you will immediately turn off the heating of everyone who lives above and below you.

However, stopcocks are still a good thing, so you shouldn’t give them up. In this situation, installing a bypass will save you. This is, in fact, an additional pipe that can ensure continuous circulation of water through the riser if the shut-off valves are blocked.

For this purpose, the bypass is located in front of the taps. Moreover, it can either connect sections of the riser directly or be shifted towards the bend of the coil. The idea is to give hot water an extra path when it can't get through to the heated towel rail. This way its circulation will not be disrupted.

Again, keep in mind that installing a valve on the bypass itself is just as categorically prohibited as on the riser itself. The reason is the same: you should not be able to cut off your neighbors' hot water supply to the bathroom heating system. Of course, if you live in a private house, you can place shut-off valves anywhere. But in apartment buildings you will have to take into account the existing rules.

Lateral and diagonal pattern

Source: https://stroyday.ru/

Such connection methods are most often used for ladder-shaped heated towel rails. The installation procedure itself is quite simple, and there are not so many initial requirements: you can place the equipment at any distance from the riser, do not displace the bypass, do not depend on the direction of water supply, the height from the floor level is also not important.

But there are several rules that must be followed during installation so that the system functions without failures:

the line used to connect the equipment should not be bent, since air can accumulate in such places, interfering with the passage of water;
Care must be taken when placing tie-in points on the riser. The lower one should be located below the corresponding connection pipe. The top one is similar, above the corresponding pipe;
it is also necessary to form a slope of approximately 0.2 to 0.3 cm for each linear meter eyeliners;
if the supply pipes are made of polypropylene, then their diameter should be DN25. For steel pipes this figure is equal to three quarters of an inch;
polypropylene supply pipes also somewhat limit the possible distance of the heated towel rail from the riser - this distance should not exceed four and a half meters;
It is highly desirable to provide the pipes with a thermal insulation layer. If they are mounted inside the wall, then this condition becomes mandatory.

Bottom diagram

A heated towel rail connected using a connection located below looks interesting and aesthetically pleasing. True, its operating efficiency is slightly lower than with other connection options. However, this option is quite popular. There are several working connection schemes for this model:

with direct bypass. An indispensable condition is installation on one of the verticals of the Mayevsky crane. As a rule, it is included in the equipment package. Drain valves are necessary in order to be able to get rid of the presence of air in the system after cases of water supply shutdown. So that these details do not disturb their appearance appearance premises, they are usually masked using a special decorative cap;
with an extended vertical bottom line. This scheme is practically no different from the previous one. It is necessary for those cases when you need to place horizontal pipes eyeliners as low as possible to the floor;
with a narrowed bypass. In this case, the upper outlet should have a slight rise towards the heated towel rail; this figure should be from 5 to 20 millimeters per meter of pipe;
with offset bypass. In this case, its diameter should be equal to diameter boner

General installation rules

Regardless of the chosen connection scheme, there are general principles, according to which installation is carried out:

In order to correctly place the equipment, do not be lazy to first mark it on the wall using a tape measure and a marker. During work, regularly check the evenness of the product using building level. This will help avoid disappointment and rework;
All joints must be carefully compacted and sealed. Tow is usually used as a sealant, which is wrapped around the joints. Teflon gaskets are best suited for seals;
All nuts must be tightened smoothly to avoid the possibility of thread stripping. It is advisable to place a piece of soft cloth under the wrench;
all elements of the heated towel rail are attached in a gentle way, hard is unacceptable due to temperature changes;
after the installation has been completed and all joints have been carefully sealed, it is necessary to open the shut-off valves to supply hot water to the system. The taps must be opened smoothly, otherwise there is a high risk of water hammer, which can instantly damage the system;
all elements of the system must be made of the same type of metal, otherwise electrolytic corrosion may occur;
if you plan to disguise the riser or supply pipes in the wall, then after complete installation system, first test it for operability, and only then proceed to finishing works. In this case, you will be able to notice a leak at any connection point. If most of the joints are hidden in the wall, then you will be able to see this problem only after it develops into a much larger one;
During installation, it is important to maintain the distance between the wall and the equipment. It depends on the diameter of the pipes. If it is more than two and a half centimeters, then there should be 5–7 cm from the heated towel rail to the wall. If the diameter of the pipes is smaller, then the required distance is reduced, it should be from 3.5 to 4 centimeters.

It is not for nothing that installing a water heated towel rail made of stainless steel raises so many questions, especially for those who have very rarely encountered this before plumbing work. Now you can see how much various nuances must be taken into account .

However, it is quite possible to do this work yourself. If you are missing some information, I recommend watching the video, the link to which I will leave below. Visual lessons are often learned better than the text read, or simply complement it, ultimately giving required level knowledge.

However, if you still doubt your abilities, then it is better to call a specialist to carry out this type of work. After all, we are talking not just about water supply, but about very high temperatures. The failure of an incorrectly installed heated towel rail is extremely unpleasant, because very hot water pours onto the floor under quite strong pressure.

In my practice, there have been cases of such calls more than once. As a rule, by the time emergency service manages to get to the desired address (and this is not that long), the apartment often turns out to be almost flooded. At the same time, moving along it is quite difficult, given the temperature of the water.

If previously a heated towel rail could rarely be found in restrooms, the product was more considered a luxury item and a whim, but today the situation has changed radically - providing comfort and coziness of the room, a sufficient level of air ventilation.

Thanks to the heated towel rail, the room can be protected from increased humidity and relieve household members from unpleasant odor, which can occur due to dampness lurking nearby. Thus, the device not only creates comfortable atmosphere, but also creates a healthy microclimate for everyone living in an apartment or house.

However, in order for the product to perform all the above stated functions, you should know how to install a heated towel rail; doing it yourself is not at all difficult.

Types of heated towel rails

To install a heated towel rail, you need to thoroughly understand which device is of higher quality and better. The following product models are available for sale:

aquatic;
electrical;
combined - characterized by the properties of water and electrical samples.

Aquatic specimens

Heated towel rails, which were installed back in Soviet times, have not lost their popularity to this day. Of course, such a device will be useless if there is no hot water supply in the apartment or there is a heating problem.

When purchasing a product, do not forget to ask the seller what material the device is made of, because surges in the entire heating system have not been canceled. It is also necessary to discuss the issue of processing seams and threads when you decide on the coil, because the connection with the pipes in the room should be strong, this will help to avoid unpleasant situations in the future. It is better to request to read the instructions for the model or read them yourself on the packaging.

The fact that there is no need to ground the heated towel rail is also important, because the device does not need electricity to heat the room. The devices themselves are equipped with special valves, which during repairs allow you to do without blocking the water supply of the remaining residents of the high-rise building; you just need to turn the valve.

The low cost of the equipment is pleasantly surprising. In terms of material, the most commonly used materials in water feature construction are copper, brass, and stainless steel.

Electrical appliances

This type is suitable if certain difficulties arise when connecting other products. There are electric heated towel rails. Wall-mounted ones are more common, choose such a model for general interior much simpler.

Of course, they have a number of other tangible advantages that may be of interest to the consumer:

such specimens can be installed in any place convenient for you, regardless of where the water supply is located;
even if it hasn’t appeared in your apartment yet central heating, you can already afford to use a heated towel rail. The main thing is that there is light in the room;
the device has temperature control;
installation of the device is so simple and straightforward that even a beginner can handle it.

If this option suits you better, pay attention to the amount of power consumption of the product. Agree, paying exorbitant bills for using the unit is not so pleasant. Do not hesitate to ask questions about the energy consumption of equipment in the store - this approach will allow you to at least approximately calculate the monthly cash expenses for electricity.

Find out how the model you like connects. Public method provides for equipping the product with a socket and plug. For the closed method you will have to tinker, because in this case the wires are hidden in the wall.

Combined samples

Something between water and electric heated towel rails, but the design is more similar to the first. Heating is not carried out without water supply from central system, however, the water can be heated by its own heating parts located inside the device.

Taking into account the total component, the cost of such devices is several times higher than their analogues.

Installation of heated towel rail

What can't you do without?

Before making a heated towel rail, you need to understand what you will have to face during the work process, namely:

The first step is to disconnect the old model; alternatively, you may need to cut the pipes in order to exactly match the height to the new design.
It is important to correctly select the necessary fittings and connecting elements and fasteners.
Mount the ball valves and supply the product itself.

Of course, during installation you will need a number of materials and tools, without which it is impossible to cope with the installation of a heated towel rail:

product;
brackets;
pipes from 26 to 32 mm in diameter;
construction knife;
screwdriver;
Bulgarian;
fasteners;
hammer, a level with which you can check the horizontalness of the part;
linen winding;
ball valves;
water sockets;
knee;
coupling with internal thread.

You may be hesitant about which pipes to choose. Expensive metal-plastic materials are not particularly durable, so pay attention to polypropylene. Despite low price the latter material, products made from it are quite durable.

Some purchase copper pipes, forgetting - to work with them, you need to have a lot of skills and experience. If you have them, go for it.

First you need to remove the old one. To do this, you will need a grinder, and if the design includes a thread, you can simply unscrew the unnecessary model and put it aside.

Before you begin connecting a new product, make sure that all necessary fasteners are included in the kit. Make it a rule to always clarify such nuances in advance. If something is missing, you should purchase additional parts and necessary elements.

Decide on the area of the room where the device will be located - how close to risers and other structures in the room. The technology allows you to place the heated towel rail at a distance of 60 cm or more from the shower, sink or other plumbing fixtures.

Place the device against the wall and use a marker to mark where the holes need to be made. To ensure that the product is fixed evenly, use a level and secure the heated towel rail - they are the ones who regulate the distance from the product to the wall.

Threaded connections are sealed with linen winding. To direct water from top to bottom, connect the main liquid supply to the upper socket. The Mayevsky tap should be located at the top; it will allow you to get rid of excess air. Screwing the nut fasteners is carried out through fabric, which eliminates the appearance of external damage, for example, scratches. Do not tighten the fasteners as much as possible, as you may ruin the threads.

Finally you have finished installing the heated towel rail. It's time to check it for leaks and the appearance or absence of leaks during operation. Gradually run the water and carefully feel the device with your fingers.

You should carefully check the tightness of all connections

Installation electric model requires an outlet in the room; you provide the cord yourself.

Conclusion

As you can see, you don’t need to be a big specialist to install a heated towel rail. It is enough to thoroughly understand all stages of installation and have the desire to complete the job.

The bathroom is a room where special comfort is required, because there a person appears in his most vulnerable state. To support optimal temperature in the bathroom, a heated towel rail is installed there. A heated towel rail is a curved pipe that is built into the general heating system of the house, necessary to heat and reduce humidity in the bathroom. In this article we will tell you how to attach a heated towel rail with your own hands.

What is a heated towel rail?

A heated towel rail or coil is a device that plays the role of additional radiator. It performs the function of heating and regulating humidity in the bathroom. Typically, a heated towel rail is mounted on the wall using brackets or other suitable fasteners.

The following types of devices are distinguished:

Important! Whatever the bathroom radiator, it is important to provide a reliable, durable mount for the heated towel rail. Since the device is usually mounted on walls, the fixtures must support its weight. The installation height is usually 100-130 cm from the floor.

Bracket device

Previously, when construction stores We weren’t spoiled with such variety; the installation of radiators in the bathroom was carried out using ordinary metal hooks fixed to the wall.

However, in practice, this installation method turned out to be quite unreliable - the battery wanders around and is not fixed securely. Now special brackets are used for these purposes. They have the following device:

Remember that to hang a heated towel rail, depending on the size, weight and shape, you may need from 2 to 6 brackets. The larger and heavier the device, the more fixation points are needed to distribute it more evenly across the supports.

Types of fastenings

The choice of mounts for heated towel rails is quite varied in design and price. Usually all the necessary fasteners are supplied directly with the selected bath radiator, so you don’t have to think about how to fix it on the wall.

The manufacturer carefully calculates how much a specific coil model weighs, and then selects brackets for it with a suitable bearing capacity and design. There are the following most popular types fastenings:

Please note that it is usually quite easy to select universal fasteners for heated towel rails if you do not want to deal with a standard fastening. It is better that the design of the brackets is detachable, since it is much easier to mount the radiator using them. When purchasing fasteners, it is important to consider the diameter of the pipe, the desired distance from the wall to the device, as well as the resistance of the material to corrosion, since the bathroom is a room with high humidity.

How is the fastening done?

The process of hanging a battery in the bathroom is quite simple, so you can even do this work yourself. It is important to remember that replacement of a water heated towel rail is carried out only outside heating season, otherwise you will have to turn off the entire heating riser, which causes inconvenience for other residents.