How to make a neat stream in your dacha with your own hands. Artificial stream at the dacha: from planning to design of the banks Do-it-yourself stream on the site

A babbling brook surrounded by stones and flowering plants will decorate any country property,
Its construction is usually trusted to professionals, but on a small scale it is quite possible to do it on your own.

To create a stream at your dacha, a small difference in levels in the garden is enough. You are lucky if your site has a natural slope - we simply place the source higher and dig the channel down the slope. What if the area is horizontal? We will have to raise the source above the mouth. How much depends on the goal: whether you want a quiet stream or a stormy stream. To obtain a “swift” stream, the difference should be about 3 cm per 1 m of length.

Accordingly, if the length of the future stream is 5 m, the difference is needed 8-15 cm, for 10 m - 30 cm, etc.

We organize the movement of water

The water in the country stream moves in a closed cycle (that is, in a circle), so it needs a pump. Use of powerful water pumping surface pump involves the installation of a special pit near the source that protects the pump from weather influences. The water, having passed through the pump, flows down the stream to the receiving pond at the mouth, from where it is sucked in and delivered back to the pump through a pipe, completing the circle. The submersible pump is simply lowered into the receiving pond.

Water from the pond flows under pressure through pipes or hoses upward to the source, from where it flows back into the pond. This option is suitable only for short streams with a slight slope and a leisurely flow.

We are installing a water supply system

The depth of the receiving pond must be sufficient to fill the entire system with water. At the mouth, overflow is required to drain excess water formed after heavy rain. A polypropylene pipe is used as a water supply. Most often it is laid along the shortest path from source to mouth, but this has its drawbacks. For example, if you plan to plant a coastal zone woody plants or build a gazebo, then repairing such a water supply may later become a problem.

In this case, it is better to make the channel less winding so that pipes can be laid along the bank or used for the same purpose flexible hose increased strength. In this case, the trench for laying the pipe is dug simultaneously with laying the waterproofing at a distance of 60-90 cm from the riverbed. At the point of emergence water pipe decorated with large stones, imitating a spring.

Making a stream with your own hands

1. Choose a location for the stream. If the area is flat, then the movement of water will be calm. On the slope you can create something like a mountain river with rapids and water flowing over flat stones. Mark the riverbed, the receiving pond at the mouth, and the line of bank fill with pebbles using twine stretched over pegs.

2. Dig a receiving pond about 80 cm deep and a trench in place of the riverbed about 40 cm deep, with a slight slope towards the pond. Clean the bed of roots, small stones and other inclusions. Compact the bottom along its entire length, cover it with a 15 cm thick layer of sand. Lay geotextiles and PVC film, or butyl rubber.

3. Press the edges of the film with bricks without stretching it.

To ensure that the film presses tightly to the bottom, run water down the stream.

Form folds of film and press turns and large folds with boulders or flat stones, scattering them picturesquely along the entire path of the water flow.

4. Fill the bottom with small pebbles with a layer of 5-7 cm. Lay stones of different fractions so that, in addition to a skillful decorative imitation natural reservoir, they pressed the walls of the film along the slopes of the stream and hid the film from the sun's rays.

By placing large stones on the bottom, you can get beautiful effect from small thresholds.

5. Fill the stream again with water to check how correctly the location for each stone was found.

Trim the excess edges of the film. In places where the film extends far enough to the shore, you can not cut it, but make cross-shaped cuts, bend the edges and plant plants in the resulting windows.

Moisture-loving hostas, astilbes, and volzhankas are perfect for this purpose.

Our advice

To connect the pump cable to the electrical network, you can use the sockets of nearby buildings or arrange a special outdoor electrical panel, hiding it in plant compositions or behind large stones.

6. To form a wide coastal zone with rocky fill, lay PVC film on the area cleared of weeds and stones. Tuck its edges under the folds of the pond film or place it on top with a slight overlap. The film will serve as a barrier to weeds. Then lay out large and medium stones and cover with fine pebbles in a layer about 4 cm thick.

7. The receiving reservoir is arranged similarly to the bed of a stream - lined with geotextiles and butyl rubber film on top sand cushion. Then the bottom is covered with small pebbles in a layer of 5-7 cm and large stones are laid. If the edges are steep, they may require reinforcement with a special mesh or gabions. More flat banks are tightly lined with large flat stones, which are installed at an angle.

8. Landscaping the coastal zone in such a way that there are not too many shoots hanging over the water, otherwise the water will quickly become clogged with falling leaves. Excellent for this purpose conifers, hydrangeas, Siberian irises, low-growing shrubs such as Japanese spirea, dwarf birch.

9. If there is a lot of soil left after digging a water feature, it can be used to form a steep slope near the stream. It is terraced and covered with materials that suit the style. They plant on the hill alpine plants or continue the theme of decorating the shore.

Stream arrangement

Men's denim jackets with hood denim jackets new spring autumn...

In the spring, we plan to get serious about equipping our dacha, or rather, bringing beauty to the site and creating landscape design. There are thoughts about the reservoir - what would it be like without it? At least small, I think, but it’s necessary.

The old owners left us two old bathtubs on the property, and I remember my own publication about that (and I will be guided by it).

Now, traveling through the parks and beautiful gardens, I constantly come across artificial streams and I wanted to figure out how to arrange one on my site. Is it difficult and how realistic is it in our Russian conditions?

We are lucky (at least we think so) - our site has a very pronounced natural slope. For garden work- this is a minus, but it opens up great opportunities for creating beautiful landscape design.

Therefore, when creating a stream, we will not have to carry out complex earthworks. But those who have a flat plot will have to additionally create a slight slope in the place where the stream is expected.

It goes without saying that the source of the stream should be significantly higher than the place where it flows into a small body of water (at the mouth we plan to make small pond). For those whose slope is practically invisible, you need to think about which direction the water will flow, so to speak, outline the direction of the flow, and then form elevation differences.

What could be the slope?

There are certain recommendations for slope. It turns out that even if you make a difference of 3 cm by 1 meter, the movement of water will already be noticeable to the eye. With a smaller slope, the water will still flow where it should, but for a person it will be almost imperceptible.

Of course, it’s nice when the stream meanders through the trees and gurgles, so it was necessary to make the height difference larger and add natural rapids where the water will have to overcome obstacles.

The simplest option

One of the simplest options for creating an artificial stream is to make a channel from a finished asbestos-cement pipe. It can be cut lengthwise, placed on a slope, or stones placed in the riverbed. different sizes- and you will get a stream. The movement of water is carried out using a pump located in the lower reservoir. Through a hose coming from the pump, which we will disguise under the riverbed or on the side of it, water will be supplied upward. Here's the simplest solution.

However, if we want to get closer to the more natural, natural look stream - you will have to work hard with a shovel in your hands!

Option with ledges and small waterfalls

In order for a stream to evoke more emotions, of course, it needs to gurgle and look natural. Eh, now I remember the mountain streams in the Elbrus region, with pure water and a wonderful sound that makes you want to meditate. This is the kind of stream I want to build in my dacha! What will need to be done for this?

First, you need to dig a channel with a large slope, suggesting several drops along its entire length, where the water will create a beautiful sound when falling from a small height. Essentially, we create small artificial waterfalls (or at least one drop - in front of our patio or relaxation area.)

The stream bed should be clean, there should be no large stones, any sharp protrusions, roots, etc. in it, since we plan to cover it later plastic film. Under the film we lay a layer of sand or clay at least 5-6 cm thick.

It is possible to make the channel concrete, for decoration on top concrete base You can put pebbles or cobblestones on the solution. Such a channel will need to be carefully protected from moisture during the winter.

If it is not sufficiently protected from autumn rains, water that gets into the riverbed and reservoirs will freeze in winter and can rupture the bottom of the reservoir. This will cause it to become covered with cracks, into which some of the water will leak in the summer.

You can make a number of reservoirs, between which small waterfalls will be arranged. Water will accumulate in each subsequent reservoir, and then will fall into the next ones, creating a beautiful murmur. To do this, we tilt the bottom of the tank in the direction opposite to the flow of the stream.

Option with flat stones

You can also form ledges using large flat stones, placing them on the bottom of the stream at a slight slope directed against the flow of water.

This will also require making the initial slope of the channel as large as possible.

And in this example you can see that the sides of the lower tank are simply made of bricks laid out in a circle, covered with film on top. Cheap and cheerful, as they say.

Stepwise option

In order for the water not to flow down the slope, but to fall with an even more powerful sound, you will need to make a ledge that will look in cross-section like a stair step with a riser that drops a few centimeters. Like this:

This option is more complex to implement, but also more effective.

How to choose a film for the bottom

I think it all depends on how big the stream is and how much water circulation is planned for it. In supermarkets for garden supplies, such as Leroy Merlin, there is a special super-durable film for ponds.

When creating a very small stream, I think you can simply use the largest garbage bags (they can be really huge and dense). In general, there is a choice for every occasion and for every wallet.

A few more photos for inspiration

These ponds were photographed by me in the center of Mantaek Chia "Tao Garden" in Chiang Mai.

This is just an example of a lotus pond.

And this decorative pond two artificial streams flow into it at once! It was very pleasant to sit next to him and listen to the murmur, amplified twice as loud.

An interesting idea - a waterfall lost in a flower bed.

An example of a pond wall design.

The artificial streams in the park amaze with their variety of design solutions.

Fresh cheap and simple idea

To implement it you will need:

• plastic bottles of 5 or 6 liters,
• black polyethylene film and
• pond pump or hose pump
• plastic basin

And also pebbles or gravel to line and support the bed of plastic bottles.

You probably already guessed - that the stream bed will be made of plastic bottles cut across, from which the upper part and bottoms. The bed laid out in this way is covered with a film, the pump is installed in a lower reservoir made of plastic bottle, wrapped in black film.

Along the contour, the stream bed is filled with gravel or decorated with pebbles. As a lower reservoir, we use a plastic basin into which we immerse the pump, and hide the hose with water coming from the pump in the same pebbles and bring it to the “source of the stream.”

Here’s a simple and completely dismountable option for constructing an artificial stream for the winter, and then... use your imagination! It's so exciting.

When decorating a local area, a number of difficulties arise even at the design stage. Many forms of modern landscape design, although impressive in their effectiveness, are clearly visible artificial origin. Owners of cottages and summer cottages strive to reproduce an attractive, but as natural as possible picture of nature. The easiest way to emphasize the naturalness of the landscape is to create a stream.

The first task you have to deal with is choosing the location of the stream and its shape. When creating a project, be sure to consider the following criteria:

To make a decision faster, consider the following recommendations:

Stream dimensions

Determine the length, width and depth of the stream yourself, taking into account your personal vision of the artistic painting of the landscape.

But take into account the standard indicators used when creating an artificial stream in the country:

What is special about the structure of the stream?

Unlike other types artificial reservoirs, when arranging an artificial stream on a site, it is necessary to purchase and install a pump. With its help, constant circulation of water will occur.

Which pump to choose?

For this form of landscape design, use a submersible pump, as such equipment will provide the necessary results at low cost.

Among the advantages of such an installation, we highlight the following points:

Suitable Type pumping system choose based on the characteristics of the artificial stream being created:

What material should I choose to cover the bottom?

Most often used to form a stream bed following types materials:

How to correctly calculate the required volume of water?

To correctly determine the required volume for the stable functioning of an artificial stream, make a simple calculation by multiplying all its parameters.

Let's give clear example for the following sizes:

Calculation formula

How to properly design an artificial stream?

Depending on the type of material chosen for lining the riverbed, the construction technology will vary slightly. But general rules remain unchanged. Carefully read the sequence of work to complete the entire volume as correctly as possible.

What materials should be prepared for the construction of an artificial stream?

Artificial stream construction technology

When designing an artificial stream, adhere to the following recommendations:

What plants should I use to decorate the coastal zone?

To decorate the riparian zone of the stream, plant plants that prefer high humidity conditions.

Among all available types, the following are especially popular among landscape designers:

When choosing stones, be guided by the style of the designed source. To arrange a mountain rapid stream, give preference to medium-sized granite fragments or a scattering of pebbles. Decorate the meadow stream with large blocks, boulders or small particles of sandstone.

Video

Watch the video, which clearly shows the entire process of creating an artificial stream to more clearly imagine the scope of work.

Conclusion

The entire process of creating an artificial stream on the site will not take much time and effort. At the same time, if the work is done correctly, it will certainly add a special flavor to the entire landscape and will begin to attract attention with its effectiveness. Therefore, carefully consider all the rules and recommendations, give preference only quality materials to get the result you expect.

A cheerful babbling brook in the countryside adds inspiration to any garden. How nice it is to let streams of clean and cool water run through your fingers on a hot summer day! In addition, murmuring water promotes relaxation and stress relief, which, unfortunately, is enough in our hectic lives.

A dacha stream presupposes the presence of at least a small reservoir on the site, but what if there is none? In this case, you can create small pond with your own hands. There is already a good article about this. It’s so nice to have a pond in your dacha, and a cheerfully singing stream – even more so! In addition, the stream will saturate the pond with oxygen and will not allow the water to stagnate. This is the mini-circulation of water on your suburban area 🙂

Having even small pond, making a stream on the site will not work a lot of work. To equip it, a powerful pump is installed at the bottom of the source reservoir, from which hoses are pulled or polypropylene pipes(depending on the configuration of the pumping equipment) along the entire bed of the stream. Then the reservoir is filled, the pump is turned on, and water under pressure is supplied to the source of the dacha stream, and then the stream returns “home” again - to the dacha pond. The shores are decorated to taste. Now let's look at how to do all this correctly.

Sectional diagram of the stream

Planning the bed of a dacha stream

The “character” of the dacha stream will be determined immediately and will depend on the topography of your site. If the slope for the stream equipment is gentle, then it will flow slowly, without a soothing murmur. But to create a babbling stream, you will need steep slopes and large boulders in the center of the channel, from which the water will fall in a continuous stream, revealing in your pioneer all the signs of a real “highlander.”

When planning the course of a stream, take advantage of the natural topography of the area. A stream can bend around your flower beds, flow next to trees, babble near recreation areas, or meander beautifully around garden sculptures, somewhere creating quiet backwaters, and somewhere – small waterfalls, shallows or islands. Make it as natural as possible, following smooth natural shapes. Some summer residents draw the bed of a country stream along garden paths, trying to give it the correct geometric shape. But replacing natural lines with strict geometry does not look very aesthetically pleasing; in addition, such a stream in the countryside often turns into an ordinary ditch and may well blur your garden paths during heavy rainfalls.

At the stream bed planning stage, consider creating artificial waterfall(if the terrain allows), as well as the organization of a receiving reservoir, that is, a second pond in the country. This is necessary if you plan to create a fairly long stream that goes around a decent part of your site. In this case, you may have to buy additional pumping equipment to install it in a second reservoir, it will depend on the length of the stream and the features of the terrain where it flows.

The coast of the ponds can be decorated beautiful flowering plants, which love constantly moist soil: sedge, meadowsweet, hosta, bergenia, bathhouse and others. Choose the length and width of the stream bed at your discretion, but standard sizes usually vary within 0.5-1.5 m - width and 0.3-0.5 m - depth.

Stages of creating a stream on the site

Stage 1. So, you have decided on the terrain and figured out where your stream will flow. Now arm yourself with a rope and pegs and walk along the bed of the future stream, driving the pegs close to each other and loosely connecting them with a rope (we don’t need strict geometry).

Stage 2. Dig the soil under the stream bed to the depth you planned. Add steps if the slope allows. Instead of thresholds along a steep riverbed, you can fix large boulders in some places (you can use concrete mortar) or make masonry, but the riverbed itself must be thoroughly cleared of stones and plant roots and the soil compacted. If you are building a large stream, then it is better to concrete its bed, and in the places designated for rapids, lay down flat stones and fasten them with concrete mortar.

Stage 3. You may want to build a stream mouth and decorate it with water and coastal plants(for example, like in this photo).

In this case, from the edge of the reservoir where the stream will flow, expose the waterproofing coating and make a trench for the mouth. Sprinkle it with a layer of sand or crushed stone 5-7 cm high, then cover it with geotextiles so that there is a margin around the edges. Then thoroughly moisten the geotextile fabric (you can water it with a hose). This is done so that the geotextile fits tightly around the mouth. Then secure the canvas on the sides with large stones, and in the middle of the riverbed make masonry: stack flat stones, securing them with concrete mortar. Apply another layer on top of the masonry concrete mortar and decorate the structure with pebbles.

Stage 4. Dig shallow (up to 10 cm) grooves parallel to the stream bed and lay hoses (or pipes) from the pump there. Fill the grooves and mask them with a layer of turf. Connect the pump, turn on the water and that’s it - the babbling dacha stream has come into its own!

There are many other ways to build a country stream with your own hands, but more on that in the next article. I described the most the simplest way, which even a novice summer resident can handle without dwelling on the details.

We beautify the dacha stream

Now your babbling friend needs to be refined. Along the entire path of the stream, you can place beautiful rounded stones on its banks, alternating them with water-loving plants: low-growing moss, primroses, daylilies, ostrichberries, ferns and others. And the bed of a country stream is usually decorated with creeping plants: tenacious, loosestrife, speedwell, etc., which gives it a piquant decorative effect. It is better to plant all plants along the path of the stream in groups to give a natural look to the landscape. Also, the banks and mouth of the stream can be beautifully decorated with “weeping” plants with a crown hanging down to the water, for example, goat willow or tree caragana. And a little further away you can plant jasmine, forsythia or lilac and enjoy not only the sound of water, but also the wonderful smell of flowers.

Caring for a country stream

If you built a country stream correctly, taking into account all the features of the relief, then further care behind him is not complicated at all. You just need to adhere to the following rules:

As necessary, add fresh water to the source reservoir where the pump is installed, so it will eventually go into the ground.
Completely drain the water from the reservoir and fill it with fresh water once a year.
Keep it tidy submersible pump: Clean filters regularly and ensure that hoses (pipes) are in good condition.
Clear away silt decorative stones on the shore as they become polluted.
In winter, it is better to drain the stream, completely freeing it of water.

It is always pleasant to see the fruits of your handiwork, but it is doubly pleasant to hear and feel them. A babbling brook can turn into a true friend for us. He will console you difficult moment, will calm you down, help you relax and allow you to forget about pressing problems at least for a while. Is there a dacha stream in your suburban area?

The element of water has long attracted people with its tranquility, atmosphere of harmony and unity with nature. When improving the garden area, there is often a desire to create an artificial pond. If conditions are not conducive to placing a pond, then optimal solution It will become a dry stream. There is not a drop of water in the composition - only cobblestones and stones imitating the mouth and bed of a dry reservoir. Planning and laying out a “stone stream” is quite simple. The main thing is to show creativity and imagination, choose the right form of the composition and follow a simple technology for arranging stones.

Landscape design: do-it-yourself dry stream. Advantages of the composition.

Classic decoration method Japanese garden increasingly used in summer cottages and local areas. In Japan water element is associated with the desire for life and purity of thoughts, and babbling streams - with the transience of time. If arranging a pond in the garden is impossible for certain reasons, then oriental decorators use special welcome- dry stream. Stone ponds convey the feeling of a dry riverbed, which with the onset of rain will be filled with long-awaited moisture.

The undeniable advantages of creating a dry stream on your site with your own hands include:

Types of dry ponds on the site

There is no specific classification of dry streams into subspecies. Conventionally, the design of such a composition is divided into three types.

winding body of water. A simple option for creating a dry stream with your own hands. One channel flows through the site, sometimes expanding and sometimes narrowing along its length. Landscape composition imitates the movement of an ordinary river. When planning the shape, it is necessary to take into account the relief, directing the reservoir along a plain or a small slope.

Cascade. The beginning of the waterfall is located at any elevation. You can create a symbolic representation of a rock, a wooden or stone well, or a large jug. The water flow falls and forms man-made rapids.

Branched channel. The natural confluence of branches requires proper placement and compliance with the natural shapes of the reservoir. The stream looks beautiful on the winding hills. For authenticity, the sources of the riverbed are often hidden behind decorative bridge, dense vegetation or fence. Sand jets are made from small pebbles or sand. Imitation of a wave is achieved by creating winding shallow grooves.

DIY dry stream: step-by-step instructions

Every summer resident and gardener can make a dry stream with their hands. There is no need to attract specialists, use expensive equipment or carry out large-scale preparation of the territory. The main task is to present the plan of the proposed stream as accurately as possible and play with the existing site.

Selecting a location and marking the site

The dimensions and configuration of the reservoir should be selected taking into account the size of the plot, the location of the house, additional buildings and terrain features. When planning, you should consider some nuances:

Marking a stone reservoir is done with sand. A sandy path is laid along the boundaries of the future “water” flow. In the process, the shape can be easily adjusted, bringing the sketch to an ideal representation of the stream. Sometimes boundaries are marked with pegs and ropes. However, this method is more labor-intensive and less mobile.

Materials for laying a dry stream

A dry stream at the dacha is created with your own hands using various rocks. By experimenting and combining all kinds of fractions, textures and colors of stones, you can achieve an illusory effect. The following materials will be useful in your work: shell rock, crushed stone, limestone, pebbles, etc.

Some points about choosing and arranging stones:

• the bluish-gray color of the water surface will ensure the mixing of slate, gneiss and basalt;
• the brown-red tone of the composition will be set by marble, granite, and limestone;
• the illusion of the shine of a water stream is created by adding small glass balls or painting concrete elements with mirror paint;
• flat pebbles are suitable for simulating the dynamics of a stream and the effect of flow;
• the coastal zone stands out with large details light colors- dark elements create clear unnatural boundaries of the reservoir.

Advice. Coating the stones with varnish creates the impression of a “wet surface.” Interesting option- treatment of elements with waterproof luminous paint. At night, the stones will glow and resemble a “moon path”.

Tools you will need:

• sand for marking;
• geotextiles - the substrate under the stone can be replaced with film;
• shovel;
• rake.

Construction of a pit under the “reservoir”

The procedure for preparing the site for laying stones:

1. Dig a channel with a depth of about 20-25 cm along the marked contour.
2. Compact the bottom area and cover it with geotextile or thick film. The material will prevent grass from growing between the rocks of the stream.

Sometimes the protective film is replaced by filling cement mortar. However, this method has disadvantages: increased cost of construction, increased labor costs and complexity of redevelopment of the site.

The order of laying out the stones

1. Large cobblestones are placed along the edges, and medium-sized stones in the middle. Small fractions will fill the depths of the reservoir.
2. Stone steps of a cascade or pond, river rapids are laid out from large flat boulders. This approach will help transform a calm stream into a fast-flowing mountain river.
3. Sharp rock fragments imitate a mountain grotto.
4. Crevices are filled with large or medium-sized elements.
5. Elongated oval-shaped stones create the feeling of running water.
6. The island effect is achieved by placing a large cobblestone in the middle of the riverbed.
7. If a dry stream serves as a drainage for storm water, then it is advisable to “plant” the stones on a sand-concrete solution. Otherwise, under the influence of water pressure, they will shift and the composition will lose expressiveness.

After laying the stones, you should arrange coastal zone. Fill the perimeter of the reservoir with crushed bark or a sand layer.

Decorating the stream and its banks

It will be possible to bring a dry stream as close as possible to a real body of water with the help of plantings. Deciduous, flowering and shrubby plants. The main requirement is harmonious combination coloring of stones and “green” frames.

It is better to choose plants that, one way or another, resemble the water element:

• bushy with bluish elongated leaves and shoots;
• flowering plantings with bright blue flowers: aubrietta, lobelia, blue fescue, bearded iris, creeping tenacious and brunera;
• The following will add exoticism to the clearing: reed, pampas grass, sedge, daylily and hosta.

Do-it-yourself dry stream: photo planting diagram

Designations for the diagram:

1. - leaf-grass-bamboo;
2. - blue, yellow, blue bearded irises;
3. - low-growing lobela;
4. - creeping tenacious;
5. - bell of Polskharsky;
6. - gabrietta;
7. - large-leaved brunera;
8. - green bryozoan;
9. - tenacious creeping red-leaved;
10. - reed type arundo.

How to make a dry stream with your own hands: photo of the layout of three different compositions

Advice. When planting plants, the main thing is not to overdo it. The abundance of herbs and flower beds will oversaturate the coastal zone and turn an exquisite oriental element into a boring flower bed or an analogue of an alpine hill.

1. Lamps. Using lighting along the stream will allow you to admire the compositions at night. At artificial lighting the stones begin to “play” and shimmer with a new shade.
2. Garden figurines. The overall perception of the pond will largely depend on the choice of decor. A mounted heron or a frog planted on an island will add naturalness to the landscape, while gnomes and funny characters will transport you to a fantasy world.
3. Bridge over the stream. The item itself does not perform practical tasks, but it gives the landscape a special charm. The crossing looks harmonious, painted to match the plants growing nearby.

DIY dry stream: step-by-step creation compositions. Video

1. To support boulders, branches and beams can be laid along the banks. This solution gives naturalism to the entire composition.
2. It will be possible to beat the mouth of the stream in different ways. It can smoothly transition into a cobblestone area or patio, or be hidden behind a fence, wide fern leaves or vines.
3. On wide stone reservoirs, an impromptu sandbank made of flat boulders looks organic.
4. The idea of ​​a quiet, calm water flow is conveyed by stones of the same color. Add bright accent It will be possible with the help of contrasting shores.
5. A homemade stream, made from local minerals, blends optimally with nature.
6. Flat cobblestones of medium size, laid out edgewise, imitate fast current water flow.
7. An alternative to a dry mineral pond is flower arrangement. A stream can come from an old jug, an overturned barrel or a chest.

Features of caring for an artificial “reservoir”

Keeping the stream in original form does not cause any particular difficulties. Care measures:

• with the arrival of spring, the soil along the banks must be fluffed up and the plants fertilized;
• make sure that ants do not grow in the crevices between the stones;
• Periodically during the hot season, the stream must be watered - this will improve the microclimate near the dry reservoir and will promote the normal growth of “riparian” plants;
• After a while, moss may appear on the stones; so that the composition does not become gloomy, its quantity should be controlled;
• Shrubs must be periodically pruned, and plants that prefer warm climates must be covered for the winter.

DIY dry stream at the dacha: photo ideas

Natural minimalism in the design of a “dried” reservoir looks very harmonious against the backdrop of majestic mountains and old tall pines.

The illusion is created that the porch country house overlooks the bed of a dry river.

A dry stream flows along dense thickets. Some of the stones are varnished, resulting in a “wet” effect.

The arrangement of a stone reservoir on the site allows you to combine several traditions and style trends from different world cultures.

The longitudinal arrangement of thin stones imitates the murmur of a stream. The relief of the area adds realism to the composition - “water” flows from top to bottom.