On this video useful attachment for a screwdriver or for an electric drill. The author recently purchased this tool for cutting sheet metal, tin, corrugated iron. The device is compact, weighs only 400 grams, easy to use. You can buy it from this Chinese store.
Equipment. In addition to the device itself, the key is included. Allen key on one side, 12 key on the other.
How does a screwdriver bit work?
The shank is screwed to the cartridge, the working part cuts the metal. The handle itself spins. And in the place where she was, there is another knife. By loosening the nuts, the blades can be rotated to any angle. They rotate around their own axis. The same nuts are fixed. The nozzle is very simple. The knives work due to the eccentric. Great for cutting sheet metal.
The video shows how a 1.5 mm thick metal sheet is cut.
This attachment is for cutting thin sheet profiled metal up to 0.8 millimeters thick. The set includes a replaceable matrix, a replaceable punch, a handle-holder. It has a low cost and is suitable for small amounts of work.
The device has two cutting surfaces. The handle must be installed before installation. When one plane is dull, unscrew the handle, turn the nozzle over, install it on the other side. We insert into the drill, fix it. You can start cutting metal.
As shown in the video, the cut is without deformation, the speed is decent.
There is a myth that the grinder cuts faster. Verification shows that this is not the case. The grinder is slightly inferior in speed to the nozzle on the drill.
The most important thing is that the cut is very even, smooth, without hooks. Cut grinder with burnt coating, burnt zinc. During cutting, there are many sparks that fall on paintwork on metal. If the sparks from the grinder fall on polymer coating, the surface for the next season may become rusty. Every self-respecting manufacturer categorically forbids cutting with a grinder. If the cutting technology is violated, it will void the warranty.
There are disadvantages when using the nozzle. You have to work with metal using both hands. On the roof, this is problematic. But on the other hand, she will perfectly cope with your roof and with the roof of a neighbor.
The jigsaw drill attachment is designed and manufactured to the highest standards, using the experience of the best British craftsmen and engineers. Cuts cleaner, faster and longer. Mounted on any drill: electric, pneumatic or cordless with a chuck up to 18 mm in size at a rotation speed of one thousand five hundred to three thousand revolutions per minute.
If you pre-drill a hole with a diameter of 12 millimeters, then this will allow you to cut a figure of almost any shape in the material. The jigsaw cuts materials at a speed of 1.5 meters per minute at a drill speed of 2500 rpm.
cuts stainless steel up to 18th density, mild mild steel up to 16th density, copper, brass, aluminum, corrugated plastic, plexiglass and fiberglass up to 14th density.
The tool performs a smooth cut even in the softest materials, which allows you to get any shape with neat edges.
After cutting, the workpiece does not need to be leveled and filed. You will be pleasantly surprised by the durability of these heads. It gives you maximum maneuverability.
If you have ever spent hours working with a hacksaw or the room is full of bad smell from the work of the grinder, then you will see the difference.
Working with metal with such a tool is safe. You can work with even the smallest details. It allows you to work freely while holding a drill in your hands when performing roofing, plumbing, bodywork, heating and ventilation work. The patented specially shaped cutter facilitates roofing and cladding work without damaging the profile of the materials.
If you are modifying a car according to the special requirements of the customer, you fit Acustic systems, perform plumbing, ventilation work, install kitchen sinks, make round or square holes, then you can no longer do without the help of a nozzle on a drill.
You can use it to cut out windows in a camper van or mobile home. It is easy to change the head punch, cutter. Depending on the goals, you can change the position of the head. There are four positions at your disposal. The tool rotates on a drill. Therefore, it is comfortable, regardless of whether you operate with your right or left hand. You have no idea how nice it is to work with him. The jigsaw cuts metal itself.
You don't even have to put in the effort. Just guide the tool or part. Cuts not only cleaner, faster and longer, but also easier. You get a lot more and pay a lot less. In the manufacture of this instrument, modern achievements of science and technology are applied. it's easy to do too.
Who has not encountered during the repair the need to cut a metal part? Among the masters, most likely there is no person who would refuse a powerful portable tool. In most cases it is used:
- grinder disk;
- milling machine;
- scissors for cutting metal.
But modern market power tools does not stand still, and now there is a nozzle on a drill for cutting metal.
Various types of cutters, as a result of repeated repeated movements, carve metal using a matrix. As a result, durable metal can be processed. In this way we cut, make holes or grind metal surface. Point influences allow you to work accurately, without disturbing the structure of the elements. In addition, the natural protective layer products.
Using nozzles, you can act on the following metals:
- two-millimeter aluminum plates;
- copper, brass, iron, zinc and steel elements;
- galvanized parts 1.5 mm thick;
- stainless steel 0.8 mm thick.
Drill use
It's no secret that a drill can be used not only as a drill, but also as a multifunctional tool. There is a whole set various devices facilitating the work of the worker.
For example:
- cutter for metal for a drill avoids monotonous handmade file;
- nozzle scissors on a drill provides the ability to cut metal sheets and elements;
- drill attachment for cutting metal tiles in turn, it helps to accurately cut sheet metal roofing at any angle.
Working with this kit requires some skill, but over time you will understand the advantages of this method.
Let's consider each option in more detail.
For cutting tiles
Another name for this drill attachment is cricket. The set is used for both smooth surfaces and profile iron sheets. The advantage of this cutter is the ability to create a smooth cut, without burrs and bumps.
The cricket drill attachment is convenient to use for:
- cutting thin-sheet products;
- cutting parts from metal sheets.
Since its application does not depend on spatial arrangement, you can easily cut a horizontal, and even a vertical sheet. 
Nozzle scissors
Of all the nozzles presented, this is the least similar to a drill. It turns the drill into electric shears instead of nibblers. They work according to the principle straight cut , cutting through the metal with sharp edges using mechanical force. This is a rougher way to cut metal and plastic. Such scissors perform only a straight cut, it is very difficult to change its direction during operation.
This set is more suitable for cordless instruments.
cutter
In another way, this nozzle is called cone. It is designed for processing wood and metal products:
- cutter replaces a file;
- significantly speeds up the grinding process;
- eliminates defects.
One set may include cones different shapes, so for each specific situation you can choose the most suitable nozzle. Some of them outwardly practically do not differ from the drill. 
Crowns for metal
In addition to the main nozzles, there are other devices, for example, a crown for metal. This is a special drill designed for making wide holes.. Its use is due to the need to lay communications. The downside of a crown for metal is its roughness: the edges of the hole made require additional processing. It is in such cases that the cutter comes into play.
The set of crowns can include both simple edges and with diamond-coated. They can be used to drill concrete floors and thick metal sheet.
riveter
Such a nozzle as a riveter on a drill differs from a conventional cutter or cutter. It is used to connect or secure with small rivets. Riveting is a rather tedious process if done by hand. In addition, you will have to use several conventional riveting tools at once. That is why riveting with a drill and a riveter is very popular with builders.
Unique fastening method requires some preparation. Special holes are pre-made in the parts using conventional drills. The riveted parts are securely connected to each other, forming a strong connection.
The nozzle on the drill helps to process metal quickly and efficiently without special expensive machines. They can be used with different types drill, but its power should not be lower than 2700 rpm. Of course, a drill is not always able to replace professional tools, but for unstable repair work she fits perfectly. Ease of use is also a plus: you do not need to spend a lot of time mastering any nozzle.
When performing construction or repair work, it often becomes necessary to cut a metal blank. To do this, use special equipment in the form of a cutter, grinder or. However, it is not always available. You can cope with the task with the help of a nozzle on a drill for cutting metal, which will cut products of small thickness.
Many craftsmen are accustomed to using a drill for its intended purpose, namely for drilling holes. But not everyone knows that this tool can be turned into a multifunctional device, supplementing it with special nozzles, fixtures and stands, which will make the drill universal and indispensable in any job.
With the help of special nozzles for a drill, which can be bought at any specialized store for affordable price, can carry out drilling of holes of various diameters, cutting, grinding, polishing, twisting, mixing and milling. There is also a pump attachment for a drill, designed to pump fluid. The attachment for plucking chickens is simply indispensable in household. With the correct and competent use of additional prefixes, the result will not be the worst quality, as well as when using a special single-purpose device, but the cost of such a universal tool will be several times lower.
By purpose, all existing nozzles are divided into:
- equipment for drilling holes and crowns;
- scissors for cutting metal;
- stops;
- corner fixtures;
- grinding and polishing nozzles;
- equipment for milling wood and metal;
- sharpening devices;
- transfer nozzles.
When working with any nozzle on a drill, you must follow the safety rules:
- the equipment must be securely fixed in the tool chuck;
- the drill must be held with two hands, which is especially important for powerful models;
- constantly adjust the pressure of the tool;
- work in personal protective equipment;
- after completion of work, do not touch the drill for several minutes to avoid burns.
What are drill bits for metal cutting?
Equipped with a special nozzle for cutting metal conventional drill turns into a punch or cotter pin. The device pierces a metal product due to the implementation of numerous reciprocating movements along the internal cavity of the matrix. As a result, a smooth cut line with a width of 3.1 mm is formed while maintaining a protective layer on the surface. sheet metal.
Important! The maximum efficiency of the nozzle is achieved only when used in conjunction with electric drill, the rotational speed of the cartridge of which is at least 2700 rpm.
The metal nozzle on the drill can handle the cutting of such metal products:
- aluminum, up to 2 mm thick;
- made of brass, copper, zinc, galvanized steel and sheet iron, up to 1.5 mm thick;
- made of stainless steel, up to 0.8 mm thick.
Using a drill bit for metal cutting has a number of advantages:
- the cut is of high quality;
- no need to keep buying Supplies which saves money.
- ensured high performance when cutting metal;
- versatility of the device;
- the equipment is convenient and easy to use and maintain;
- the nozzle can be used for electric and pneumatic drills;
- with the help of a nozzle it is possible to carry out cuts of any configuration.
Despite all the above advantages, in order to get a cut High Quality, some skills and dexterity are required for work.
Popular nozzle models
Today there is a large number of various models of nozzles for a drill, thanks to which you can not only cut metal in a straight line, but also make curly cuts. This is required for installation. ventilation ducts, roof structures, gutters. Using the nozzle allows you to cut in any spatial position without making any preliminary adjustments.
Nozzle types:
- cutting nozzle "Steel beaver" is used for cutting metal tiles, corrugated board and any flat profile sheets;
- universal nozzle "Cricket" is used for cutting profile metal, polycarbonate and plastic;
- special nozzles for curly and curved cuts are represented by the EDMA Nibbek, ACRO YT-160 A, Sparky NP 1.8 L models, which differ in the thickness of the processed sheet.
Nozzle-scissors on a drill"Steel Beaver"
A classic drill attachment for cutting metal tiles and any flat sheets from metal in the form of a freely rotating shaft in a bearing with a fixed eccentric, it works on the principle of a crank mechanism with the difference that energy is supplied here for rotation.
A complete cutting tool support part located on the frame, and movable - connected to the eccentric. It is the movable part that performs reciprocating movements during the rotation of the shaft. A mandatory element of the design is the handle, which is fixed perpendicular to the axis of rotation of the spindle. During the increase in load, a reactive torque occurs, due to which the drill advances relative to the nozzle.
It should be remembered that the tool must be placed strictly vertically relative to the workpiece when making a cut. Failure to do so may result in damage to the product and injury to the operator.
The device resembles metal scissors. The drill attachment is used for cutting flat products or profiled sheets with large radius bends. The cutting line is easily controlled. During tool operation, the protective layer of the coating is not burned, which eliminates the formation of sparks and the likelihood of burrs. You can perform continuous cutting of products of any length. You can buy a drill attachment for cutting metal tiles and flat metal sheets for 1600 rubles.
Using the “Steel Beaver” nozzle for a drill, you can make a figured cutout for mounting roof ventilation elements or a gutter
Sheet cutting is performed at a drill speed of 1500-3000 rpm. The cutting angle is 360 degrees, the minimum radius is 12 mm. With the help of the “Steel Beaver” nozzle, you can cut:
- copper or aluminum sheet 2 mm thick;
- steel - no more than 1.8 mm;
- stainless steel - up to 1.2 mm,
Helpful advice! For cutting a profiled sheet with bends of small diameter, use cutting shears of the Cricket type.
Nozzle on the drill "Cricket"
Nibblers "Cricket" got its name due to the characteristic noise during operation of the device. The nozzle is similar to the previous model, but has a different design of the working element, consisting of two cutting heads. The principle of operation of the nozzle "Cricket" is similar to an office hole punch. Accurate holes are squeezed out in the metal during oscillatory movements of the cylindrical striker with a high frequency. Thanks to translational movements along the marked line, it is possible to obtain an even cut.
Nozzle-scissors "Cricket" are used for cutting metal thin and profile sheets, and polymeric thin-sheet products up to 2 mm thick. Work can be done horizontally and vertical plane. Due to the ability of the tool to rotate 360 degrees. can drill large round holes and make artistic cuts. You can buy a nozzle for a drill for cutting metal "Cricket" for an average of 1500-4000 rubles.
The tool can cut metal with stiffeners and various profile stampings in two ways. The first option involves repeating the surface of the profile, bending around the edges. It is used for products with an average bending radius. For cutting metal tiles, another cutting option is used, according to which the tool moves along the stiffeners without bending around the sheet profile.
Before you buy a nozzle for a Cricket drill, you should consider the main drawback of the tool. Due to the fact that the punch of the nozzle has a diameter of several millimeters, when cutting the product, a cut of a certain width is formed, which leads to certain material costs. The result is crescent-shaped, sharp-edged metal shavings that should be disposed of immediately for safety reasons.
Helpful advice! When working with the tool, do not wear soft shoes.
Nozzle for drill "Cricket" does not require adjustment, easy to use and maintain
One of the most popular models is a scissor attachment "Cricket" for metal up to 1.6 mm Enkor 14210. The tool is able to cut a sufficiently thick metal sheet in a straight or curved direction. You can buy a nozzle for a drill for cutting metal for 1300 rubles. Main Feature tooling is that during the cutting process a path is formed with a width of only 1.6 mm, which provides enough good level material savings.
The device can be installed not only on a drill, but also on a screwdriver. The metal cutting attachment is lightweight, which does not add weight electrical appliance. The kit includes a replaceable handle, which increases the accuracy of the work. The device has a low noise level due to its special design, which makes working with it more comfortable.
Nozzle on a drill for sharpening drills
This device consists of a plastic case, inside which a special-shaped emery wheel rotates. It is he who allows you to form the required sharpening angle on the working part of the tool. The circle is mounted on a shaft, which is connected to the drill with a special coupling. It is activated when the tool is turned on.
Many modern models have an end cover on the body, in which there are holes of various diameters for sharpening drills different size. These holes are made in such a way that the element for sharpening is in contact with the emery wheel in a certain position.
The principle of operation of the sharpening nozzle is simple - when the drill is turned on, the chuck rotates the whetstone located inside
The process of sharpening the drill is as follows. The product is inserted with the cutting part into the nozzle hole of the corresponding diameter. After starting the drill, the emery wheel begins to rotate, sharpening half of the drill bit. Then the product is turned over in the hole by 180 degrees, and the procedure is repeated. This sequence of actions is performed several times until the required parameters of the cutting part of the drill are reached.
A drill attachment for sharpening drills, which you can buy on average for 350-500 rubles, has 15 holes with diameters from 3.5 to 10 mm. Products can be sharpened at an angle of 180 degrees thanks to special form stone. Simple design device allows you to perform work quickly and without special skills.
Related article:
Types of structures, their characteristics and features. Review the best manufacturers machine tools. Comparative characteristics rates.
However, it should be remembered that the device is intended for sharpening cutting edges. For a full-fledged sharpening of heavily worn products, an emery wheel will not be enough for a long time.
Helpful advice! Buying a nozzle specific model, consider the diameter of the drill chuck.
There is also another type of additive. This is a nozzle for a drill for sharpening knives and scissors, which is presented in the form of two emery wheels planted on a shaft and located at a certain distance from each other. The price of such a device is about 250 rubles.
The nozzle for and scissors for a drill is easy to operate, does not require special skills in its use.
Nozzle for a drill for grinding
Using a grinding attachment on a drill, old coatings, corrosion, nicks, scales are removed from the surface of the product. It is used for grinding the edge of glass, metal parts and products made of other materials. Thanks to small size equipment can handle hard-to-reach areas. average cost products is 500 rubles.
Grinding drill attachments are used for preliminary rough preparation of the base for future polishing. It is made in the form of a rod, on which grinding material is fixed in the form of a brush or sandpaper. There are various types of such devices that are used for specific tasks.
A cup attachment for a drill for grinding wood or other material is represented by a rod mounted on a chuck and a cup-shaped body filled with light or hard bristles. The body is made of metal or durable and lightweight plastic. Usually such a nozzle is used to remove old coating or corrosion from the surface.
Another variation is the disc attachment for a metal grinder, where the bristles of the grinding material in the form of a brass brush or steel wire are directed towards the edges of the disc from its center. This additive should be used very carefully, as it can easily damage the coating. The plate nozzle has a movable or fixed rod, which is fixed on the cartridge. Sandpaper is attached to it with Velcro.
Helpful advice! It is better to purchase nozzles with a movable rod, which allows you to adjust the angle of the drill, while smoothly following the contours of the material.
Petal or fan grinding head represented by a rod on which pieces are fixed sandpaper or other abrasive material. It is used to perform radius grinding or surface treatment with complex profile. It can also be used for grinding holes, as well as carbide cutters or cutters that work on the principle of a file.
Grinding abrasive stones, mounted on the stem, are used to remove sagging, burrs, boring holes or leveling the weld.
Drill bits for polishing
After grinding the base, it is necessary to give it a smooth surface. This is done by polishing using special nozzles. They can be made from felt, wool, foam or felt. According to the degree of softness, they can be hard, soft, super soft and embossed. According to the method of fastening, nozzles with a stem, with Velcro and with a holder-lock are distinguished. Fan or disk nozzles are used for polishing discs, end devices are used for holes. The average price of a product is 250-300 rubles.
Many motorists have in their arsenal a nozzle for a drill for polishing a car. However, when choosing this product, you should consider some features:
- the device must be of high quality and professional;
- for efficient and safe polishing procedures maximum amount the speed of the drill should not exceed 3000 rpm, which is indicated in the characteristics of the device, otherwise the paint will simply burn out;
- the nozzle must be from a well-known brand;
- the device should not be included in the budget products;
- for polishing each individual part of the car should be used special nozzle designed specifically for this purpose.
The process of polishing a car with a drill is a very complex and time-consuming process that requires certain skills. If there is no experience, first you need to study all the subtleties this process, master the basic techniques presented in the videos on the Internet. It is better to start with inconspicuous areas of the body. The tool is configured to the desired parameters, taking into account required number revolutions. The nozzle should not be pressed too hard against the surface to high temperature don't burn the paint.
Nozzle for a drill for plucking birds
Plucking a bird is a very time-consuming process, especially when it is necessary to process several carcasses. Therefore, many farmers were constantly looking for new solutions not only to make work easier, but also to reduce the overall time. For this purpose, a feather attachment for a drill was specially developed, which removes feathers from a bird in a matter of minutes. It is similar to a dishwashing brush, only silicone fingers act as bristles here, which, when the shaft rotates, pull feathers out of the carcass. At the same time, the bird is brought from different sides.
Nozzle for a drill for plucking birds, which you can buy on average for 1500 rubles. processes poultry carcasses in just 2-3 minutes, leaving not a single feather. The result is smooth, undamaged skin. The device is effective not only for processing chickens, but also gives a good result when plucking geese. The drill attachment can be used not only for fresh, but also for frozen poultry.
Helpful advice! It is not recommended to scald the carcass with boiling water before using the nozzle, which will reduce the efficiency of the processing process.
The main advantages of the drill attachment, which you can buy at any specialized store, are the speed, ease and portability of use, which does not require certain skills and additional processing of the carcass before plucking. A significant disadvantage of the device is that after this mechanical process, damage remains on the carcass, which worsens it. appearance. Therefore, if the bird is intended for sale, it should be plucked manually.
Other types of nozzles
When it is not possible to make a hole in the usual mode, you need to use an angled nozzle for a drill. The working head of such a device can be rotated at different angles relative to the axis of rotation of the drill chuck. The main disadvantage of the equipment is the increased risk of drill failure. Therefore, the most popular is angle nozzle for a 90 degree drill, which is fixed on the neck of the drill. The price of the product is an average of 800 rubles.
For craftsmen who are engaged in the manufacture of furniture, cutter bits are very popular. various kinds. They can be backed and pointed. With their help, you can make grooves of various shapes and depths, process holes and remove defects. The cost of equipment is in the range of 350-450 rubles.
To mix a solution of different consistency, a mixer nozzle for a drill is used, which is selected taking into account the density of the solution. So for mixing glue, liquid putties and other fluid mixtures, spiral devices are used that prevent splashing of the solution. For mixing concrete, nozzles with a tail in the form of a hexagon are used. Mixing mixtures with this nozzle will be carried out quickly and efficiently. However, in order not to reduce the efficiency of the device, it is necessary to maintain the volume of the mixture for kneading. The price of the nozzle is 500 rubles.
Helpful advice! When choosing a mixer attachment for a drill, it is necessary to take into account the power of the tool. An increase in load can lead to burnout of the winding.
Indispensable in concreting is a vibrator for concrete on a drill, the price of which is about 900 rubles. It is used to compact the concrete mass during its laying, namely, it is designed to remove bubbles and air layers from fresh concrete. The nozzle requires a drill with a power of at least 1500 watts.
For woodworking home master you just can’t do without a nozzle on a drill for cutting wood, average price which is 2000 rubles. To pump liquid, you can use a nozzle-pump.
A wide selection of different attachments, fixtures and accessories makes the drill universal tool, which is indispensable when performing repair work and for other economic needs in living conditions. It's simple and optimal solution, which will avoid the purchase of expensive specialized power tools.
There are many ways to process metal products, both industrially and manually; are used for this various tools, including a nozzle for a drill for cutting metal.
In contact with
Types of processing
Once upon a time, the only possibility for processing metal products was, but as technological progress developed, people invented more and more new methods, and now we have a fairly rich selection of such tools.
All of them can be divided into two main groups:
- thermal;
- mechanical.
Each method has its own advantages, and each requires its own toolkit.
Cut while it's hot
In thermal cutting, the cut is made using high temperatures. The following types of such processing are known:
- Gas.
- Gas-electric.
- Plasma.
Gas causes cutting by burning in oxygen, directed in the form of a jet to the site of the intended cut. Melting does not occur - the material retains its hardness, so that the cut is even.
There are also oxygen-flux and oxygen-lance options. In the first case, a flux additive is supplied to the cut site along with oxygen, which has a chemical, thermal or abrasive effect on the material, which facilitates the cutting process. With the oxygen-spear variety, the necessary temperature parameters are provided by the combustion of a steel tube through which oxygen passes.
The gas-electric method involves the use of electricity and includes two types of cutting:
- air-arc - the melt is removed by an air jet supplied under high pressure;
- oxygen-arc, when metal splashes from an electrically heated material burn in an oxygen jet, and the scale is blown away from the cut.
Gas techniques are inexpensive, relatively easy to use, but do not provide a high quality result: after them, additional processing of the cut edges is required.
Plasma processing is carried out using a plasma torch, which creates a plasma jet with heating from 5000 to 30000 degrees. The latter method has several advantages over the previously mentioned ones:
- The versatility of the application of the technique.
- High cutting speed and precision.
- Possibility of cutting along a complex curved contour.
- More high level environmental safety.
The disadvantages of this method include the high cost of equipment and the complexity of its maintenance, the noise of the process, the impossibility of processing large-sized products with a thickness of more than 8-10 cm.
Important! when carrying out heat treatment, it is necessary to observe safety precautions, protecting the face and hands from sparks and hot splashes.
Harder than iron
The mechanical version is much more accessible than the thermal one in everyday life and involves processing with tools that have a higher hardness compared to it, the use of which requires quite significant physical effort.
It can be:
- Scissors.
- Accessories for an electric drill.
When cutting metal sheets, the first type of tool is usually used. known the following types scissors:
- cutting shears for metal manual;
- slotted, powered by an electric motor;
- guillotine - manual and mechanical type.
The guillotine type is equipped with a single oblique blade moving in the same plane at an angle, so you can work with less force than when working with conventional roofing scissors.
Saws have an electric drive and are divided into:
- saber;
- disk;
- angle grinders.
Saber equipped with a kit saw blades length from 100 to 300 mm, moving along a reciprocating path. When working with them, you need a good eye.
cutting part circular saw is a disk, the diameter of which primarily determines what type of work can be performed with its help - the larger it is, the more diverse they are.
- TurboShear MALCO TSCM EV - used for profiled sheets up to 0.6 mm thick. Telescopic clamp and shank provide secure fastening. Lightweight body - aluminum, knives - high-strength steel. Design features provide the ability to rotate to any angle.
- TurboShear (punching) MALCO TSMD EV - suitable for cutting metal products up to 1.2 mm and cutting corners up to 90 degrees. Provides a perfectly even cutting line on both sides.
- Black & Decker MTS04 - designed for grinding. Also this nozzle on a drill is suitable for cutting, a tree, plastic. The tool is intended to be used for repair and construction work in everyday life.
- TurboShear MALCO TS1 EV - involves cutting steel sheets up to 1 mm thick. Fastening provides a shank. The case is aluminum. Blades made of carbon steel. This part can only be operated with both hands.
- Scissors NP 1,8 SPARKY 181874 - suitable for electric drills of any model. Able to perform linear and radius cuts, allows you to cut unalloyed steel.
Useful video: nozzle for a drill for cutting metal
The use of the above devices allows you to significantly expand the scope of the tool, making it universal. However, it cannot completely replace saws, scissors and a grinder.
There are a great many tools that can be useful in everyday life or for infrequent custom work. In order to buy, for example, the so-called "grinder", you will need a considerable amount, and in the meantime the tool will lie somewhere in the garage or workshop idle, being unclaimed.
Not every tool designed for a particular job, a person is able to buy: it will take a lot of money and extra storage space. And, as practice shows, there is simply no point in this. But there is still a way out of this situation.
Nozzles are for the following works:
- Drilling at an angle;
- grinding;
- Polishing;
- Sharpening nozzles;
- Drilling;
- For cutting metal.
As can be seen from what has been said, having only one drill and a few nozzles, you can thus replace a lot of expensive tools and not waste your money.
Basic Sheet Metal Cutting Methods
Sooner or later, every homeowner, not to mention specialists, cuts sheet metal on one scale or another. Ever since labor lessons at school, and for many after, in production, such tools for cutting metal are known:
But time goes by and technical progress does not stand still. Mankind has invented a simple and inexpensive cutting tool that works in tandem with an electric drill called "metal nibbling scissors". This equipment is simple, constructive and very convenient in operation.
When there is one in the tool arsenal of any man, as well as an electric drill, then there are no problems with cutting a metal sheet and cannot be.
And if there is none on the farm, then it can be purchased at the nearest household or construction market.
Good alternative to Bulgarian
This drill attachment has been helping out craftsmen for many years now. Such a tool is called nibbling scissors.
Easily punches a track about 3 mm thick in metal. This cutting method gives the desired cleanliness of the cut, and there is no particular need for further cleaning of the cut.
Thicknesses of materials that the scissors can cut:
- Copper and brass - 1.5 mm;
- Aluminum - 2 mm;
- Stainless steel - 0.8 mm.
For metalworking
These nozzles are scissors simple and original design, where rotary motion the drill chuck is converted to reciprocating.
Nibblers "Cricket"
The technical capabilities of the "Cricket" nozzle allow cutting metal and plastics. Moreover, the material can be cut both sheet and profile. Two cutting heads of the cutting nozzle on the drill allow cutting materials certain thickness (specified maximum thickness):
- For aluminum - 2 mm;
- For steel - 1.5 mm;
- For stainless steel - 1.2 mm;
- For plastic - 2 mm.
Additional characteristics:
- Electric drill power from 420 W;
- Turnovers - from 3000 rpm;
- Cutting radius (minimum) - 12 mm;
- The cutting direction is unlimited, hence 360 degrees.
Application area:
- Mounting;
- Roofing works;
- Production of gutters;
- Disassembly of various structures;
- Body work;
- Curly (decorative) cutting.
When working with nibblers, the drill does not require any adjustments and special skills and knowledge.
The Cricket tool for cutting metal is very maneuverable, and its capabilities are cutting tool are very wide.
As for cutting with a grinder, there are a number of disadvantages here, compared with cutting shears for metal. The nozzle on the drill has a number of significant advantages:
- The material does not overheat during cutting, which is especially valuable when cutting metal tiles.
- The maneuverability of nibblers for a drill is much higher than that of a well-known grinder.
- Higher cutting speed.
- A cleaner saw cut that rarely requires further plumbing.
- When working with nibblers for a drill, there are no jamming of the tool from distortions, which very often happens when working with a grinder, hence the almost complete absence of injuries.
- The zinc and paint-and-lacquer coating of the material does not burn, which helps prevent premature corrosion and, which is very important, maintain the guarantee for the material.
- When working with the Cricket tool for cutting metal, there are no sparks, unlike a grinder, which not only protects the material from burning, but also eliminates the possibility of injury to the eyes of the worker.
Nozzle-scissors "Cricket" has a number of analogues, for example:
- "Beaver";
- "Steel Beaver";
- Scissor attachment NP 1.8 SPARKY;
- EDMA NIBBLEX;
- Malco turboShear TS1 - can be used with a drill and for installation on a screwdriver.
All of the listed nozzles have some differences on technical specifications and prices. The most expensive nozzle is Malco turboShear TS1. It has a slightly different design and is made in the USA, not China.
It should be noted that normal work of these devices can only be provided with a passport drill speed of more than 2700 rpm.
Nozzle for screwdriver
If an electric drill is not available, then a screwdriver can also perform the same functions.
There is, however, a difference:
- The revolutions of a screwdriver are lower than those of a drill. Low speed and, accordingly, the power of the power tool will not allow cutting metal with the same productivity, especially if it is closer to 2 mm in thickness.
- Lack of inertia. After the user releases the button, the chuck immediately stops rotating. In terms of safety, this is even somewhat better, as well as in the case of a figured cut.
- Small size and light weight compared to a drill. This allows you to do all sorts of "pirouettes" when cutting, more easily than with a drill.
- Screwdrivers run on batteries, therefore, its operation is autonomous, and power cord does not interfere with normal operation.
- There is no adjustment of the rotation speed of the cartridge.
It is quite clear that a screwdriver can also be used instead of a drill with a Cricket type nozzle.
For cutting metal tiles and more
This nozzle is a real find for cutting material such as metal tiles.
Advantages:
- Does not damage the material and coating;
- Easily follows the contour of the material profile;
- Able to make cuts of varying complexity.
"Cricket" is a real find for both the handicraftsman and the professional. It can make an internal cut and can work both horizontally and vertically.
The nozzle for cutting metal tiles allows you to cut metal tiles and corrugated board, with which this tool does an excellent job. After all, it is well known that it is difficult to work by making cuts in these materials with another tool, and the Cricket copes with this task perfectly: cleanly, quickly and without errors.
Advantages and disadvantages
Advantages:
- Surface cleanliness is better than that of a grinder.
- This device can make holes ("windows") of any complexity in the metal.
- The tool is easy to use and maintain, takes up little storage space.
- Low price.
- You can cut both metal and plastic, as well as carbonate of a certain thickness, stated in the instructions for use of this equipment.
- The possibility of using the device in places where there is no power supply is compensated by the presence cordless drill. In addition, it can be successfully used in damp rooms, where using an electric drill from the mains is life-threatening.
- The device is multifunctional.
- The low weight of the device is also an undeniable advantage.
Of the shortcomings, there is the only and main one: the device must be held with both hands, which is not always convenient and safe when working at height.
In conclusion, I would like to summarize what has been said. Any user, both beginner and experienced, who does not want to overpay for a fabulously expensive tool, can always buy an inexpensive analogue that will pay for itself very quickly by performing the same functions.
Very often it turns out that suddenly there was a need to use a cutting tool, and it was not included in the plans to buy something expensive, which is not known when it will be needed (if it is needed at all).
AT this case it is cutting shears for metal that will come in very handy.
That's why cutting attachment found on a drill wide application in many branches of human activity: repair, assembly, dismantling and restoration.
Good luck with your purchase and enjoy working with the Cricket attachment for metal cutting!
