Baxi SIG-2 11 p is a gas instantaneous water heater designed for use in everyday life: in apartments, country houses or at the dacha. This model is capable of preparing the required volume extremely quickly. hot water, while being compact in size, easy to install and maintain.
Like other models from the “p” series, this water heater is equipped with piezo ignition and a thermocouple.
Advantages of the Baxi SIG-2 11 p geyser
The water heater is based on an open combustion chamber and is equipped with a piezoelectric ignition system with pilot flame. The power can be adjusted very smoothly thanks to the presence of a modulating burner. The Baxi SIG-2 11 p water heater is perfectly adapted to domestic conditions, operating stably in the range of 13.5 - 20.0 mbar without reconfiguration due to the use of a built-in gas pressure reducer.
Universal burner made of stainless steel, brass hydraulic group resistant to scale formation and heat resistant copper heat exchanger With protective coating from condensation will ensure a long service life of the column. If necessary, the Baxi SIG-2 11 p water heater can be reconfigured to operate on liquefied gas.
This model is characterized as one of the safest in its class, equipped with several protective equipment:
- draft sensor - a thermostat that guarantees the safe removal of combustion products and instantly stops the gas supply to
- burner in case of chimney obstruction (blockage, strong wind);
- control of the presence of flame using a thermocouple;
- knob for regulating gas flow and power;
- knob for regulating water flow and temperature.
The water heater is supplied with two control knobs, a filter (inserted into the fitting at the water inlet), a fitting with a gasket (attached to the inlet of the pressure regulator), as well as hooks for hanging.
You can find out more information about this model and buy a Baxi SIG-2 11 p gas water heater from the sales department.
Water heaters have a fairly wide range of applications, and for a number of reasons they are much more practical than full-fledged boilers. But even outstanding structures can break. And traditional European quality, alas, does not guarantee complete protection against such problems.
Peculiarities
It should be noted that Baxi company produces not only instantaneous, but also storage water heaters. But still, a considerable part of customers prefer speakers in the traditional sense of the word. Until recently, the products of the Italian brand in Russia belonged to the premium segment. But after the recent relocation of production facilities to Iran total cost The supply of goods has noticeably decreased, but the quality level has not changed.
Modifications and alternatives
Before talking about the speakers themselves, it is worth paying attention to alternative offers from the same concern. Storage water heaters Italian company are represented by the SAG3 model. These devices are suitable for both domestic and industrial sectors. According to the manufacturer, using them to replace outdated heating equipment means ensuring a stable supply of large quantity water.
The design difference is:
- open type gas combustion chamber;
- piezoelectric ignition;
- autonomy from power supply;
- high-quality enamel on the walls storage tank, reliably inhibits corrosion;
- Possibility of installation both on walls and on the floor;
- environmentally and sanitary-neutral thermal protection.
But there are situations when neither such equipment nor the outdated model of the Main 24 fi boiler suits consumers. In such a case, a Baxi gas water heater comes to the rescue, providing flowing water. The Italian company has developed a family of SIG-2 devices for this purpose. All of them are equipped with an open combustion chamber, but there is a certain difference. Thus, models 11i, 14i are equipped with an automatic ignition module, and the 11p version uses a piezoelectric method for producing a spark.
The energy-dependent modification 11i receives electric current for igniting gas from an Lr20 format battery supplied with the column. The system is equipped with a module that monitors air ionization characteristic of a burning flame. If it goes out, the automation sends the appropriate commands to the working nodes. The 11i is capable of providing nominal thermal power 22 kW and supply of 11 liters of heated water per minute. For the 14i version, these parameters are 29 kW, 14 liters of water.
Automatic Baxi models are equipped with a liquid crystal screen on the facade, which shows:
- preset water temperature;
- its achieved level;
- conditional error codes.
As for the mechanical controls, two of them are located on the body, respectively setting the heating of the liquid and its pressure. Manual ignition on the 11p model is achieved through the use of a prepared piezoelectric element and a control button inserted into the front panel. The advantage of a non-volatile design is its relative low cost, which is achieved, among other things, by eliminating the digital screen. The system has a thermal rating of 22 kW and a water output of 11 liters in 60 seconds.
Automatic speakers are equipped with:
- hydraulic valves;
- traction indicators;
- copper heat exchangers;
- devices that regulate water temperature;
- Setaak gas pressure indicators;
- economizers.
The copper heat exchanger is harmoniously coupled with a hydraulic group made of high-quality brass. The gas burners themselves are made from stainless steel. Any Baxi speaker is equipped with devices that provide smooth modulation of the assigned power. A reducer that controls gas pressure is also built into them. Automated models monitor the fire using an ionization element, and piezoelectric models are equipped with a thermocouple.
The technical characteristics of geysers cannot be fully described without mentioning the dimensions of the device. The 11 l model has dimensions of 58.2 x 31.4 x 24.5 cm; in the version designed for a flow of 14 l, they are increased to 65 x 36.5 x 24.5 cm. The cross-sections of the chimneys in these cases are 11 and 13 cm. Connecting both water and and gas occurs using fittings cut into ½ inch. If you change the jets, Baxi gas water heaters can be converted from natural to liquefied fuel.
Possible problems and their resolution
Even the best Italian speakers can have some technical problems. Troubleshooting directly depends on what type of equipment it is.
If there is no spark at SIG 2-11p, the reasons may be due to:
- disconnected wire of the piezoelectric part;
- impairment of her own performance;
- poor connection of the piezoelectric element;
- electrode deformation.
A different approach is needed when column 11i, 14i does not light up. First of all, it is worth checking the health of the batteries. After this, inspect the wire through which current flows to the electrode. Additionally, you will have to examine the electrode itself, the automation, and the membrane. Such manipulations and subsequent repairs (replacement) must be performed by trained specialists.
The user himself can create the required water pressure by turning the regulator to the extreme position. It happens that a spark seems to jump, but you still can’t turn on the column. Very common cause the ignition nozzle turns out to be contaminated, which is purged and cleaned mechanically. You should also check whether the electrode responsible for ignition is positioned correctly.
Additional measures include checking the opening of the gas valve, removing air trapped in the gas pipeline and replacing the problematic electronic unit. When the igniter burner goes out randomly, you will have to change either the thermocouple or the coil. Judging by customer reviews, sometimes it is discovered that the fuse is burning, but it does not initiate the combustion of the main torch. The solution to the problem is to increase the water pressure in the system or replace the worn membrane. Sometimes another problem occurs: even when the water is stopped, the burner does not go out.
The first step is to clean the gas valve seal. Then disassemble the piston or rod in the water valve; if cleaning them does not help, these parts will have to be replaced. The next step involves checking the functionality of the microswitch lever (only for automatic models). Appliances operating on liquefied gas may experience a similar problem when malfunction regulator Too long ignition, accompanied by flapping in the burner, can be “cured” by adjusting the flame strength, cleaning the fuses and injectors.
In the case when the heat exchanger plates become clogged too quickly, it can be assumed that the reason is insufficient draft or dust in the room. Inspect the chimney and increase the draft level if necessary. You can fight yellow flames if you use only the type of gas for which the column is configured. Cleaning the burners also often helps. The appearance of a gas smell means it is necessary to inspect the gas pipeline and all joints using a soapy solution, following standard precautions.
It happens that the “aroma” of gaseous combustion products spreads throughout the room. They begin to eliminate the problem by checking the draft in the chimney and the quality of smoke removal. It is also worth assessing whether gas consumption has increased excessively, because intense combustion may exceed the evacuation capacity of the chimney. If, when inserting a new battery, the column screen displays readings temperature sensor, but the system does not work when the hot tap is opened, you need to adjust the screw that presses the pusher button to the microswitch lever. Strict adherence to these recommendations will significantly extend the life of the column and get the maximum benefit from it.
About the main faults gas boiler Baxi ECO 4s, see the next video.
Kozhukhov Ilya 22.03.2018 10:38
Advantages:
Small. Not noisy. Reasonable price tag. There is both a gas regulator and a water pressure regulator. There is nothing superfluous.
Flaws:
With strong pressure, it warms the water to 40-45 degrees (winter is outside). No temperature sensor.
I still don’t understand at what point during adjustment you need to press the gas/water adjustment knobs.
General impressions:
Installed, it works. It doesn’t make noise, the average water pressure heats up to 50 degrees, so far everything is quite normal.
rust173 11.02.2017 22:31
Advantages:
Everything was done as it should.
Flaws:
Water enters at an awkward angle.
General impressions:
For some reason this column is poorly promoted. But in vain. People look at boches, vailantes, etc., which are no longer the cakes they used to be. In principle, I don’t want to get involved with the Chinese - you look at their thin heat exchanger tubes, flimsy waterworks, like made of foil, and you can’t believe that the column is working. Neva... also somehow didn’t impress me with the reviews, and the price tag for the speaker with the required functionality is something not domestic at all. I was specifically looking for one with a gas reducer (flame modulation), with a brass hydraulic unit with a reducer, and without newfangled plastic baubles in the connections, and with less electronics - no batteries. If there is protection against extinction, the column on the wick is quite satisfactory to me - the counter does not react to the wick. As for protection, there is everything necessary: against wick extinguishing, heat exchanger overheating and chimney clogging.
The speaker worked right out of the box, without tambourines or settings. Water enters, albeit at an awkward angle, but everything can be solved plastic pipes. Lights up quite quietly, without explosions. I have top floor, but the column starts vigorously, because the cross-section of the tubes on the heat exchanger is decent, and in the working part it is also enlarged, like the famous Mohr column. The heat exchanger itself is painted to protect copper from oxidation - we'll see what happens next. The column responds adequately to the controls, especially “water flow”, which is very unusual for me. Before this there was a Proton column - so when adjusting the water it simply did not light up. The knob was constantly at maximum. And here the water handle is in the middle and the column does not respond to cistern or open cold water. The heater reacts a little to the second open hot water tap - the water becomes a little cooler, and the pressure drops, of course - I’m on the top floor.
In general, I was pleased with the design - everything was done visually reliably and inspires confidence. Of course, it is too early to judge reliability - if there are incidents, I will definitely add a review. So far the flight is normal.
Gas water heaters Baxi, customer reviews for which can not often be found on websites and forums on the Internet, at first were not particularly popular among Russian consumers due to their rather high price. This brand was known in our country only for its heating products.
But everything changed a few years ago when Italian company moved the production of its gas instantaneous water heaters from Europe to Iran. The quality of materials, components and spare parts remains the same high level, but the price has now become quite affordable for domestic consumers.
Let's take a look at what the company represents on Russian market models of geysers Baxi SIG-2, technical specifications of these devices and photos appearance. We will analyze it in detail, according to the operating instructions (passport). internal structure column, let's determine together its advantages and disadvantages in comparison with its imported and domestic analogues.
Model range and features of Baxi SIG-2 geyser models
The Italian company presents Baxi gas instantaneous water heaters with open camera combustion of just a few modifications:
— with automatic ignition: Baxi SIG-2 11i and SIG-2 14i;
— with piezo ignition: Baxi SIG-2 11p.
Geyser Baxi SIG-2 11i
Geysers with automatic electronic ignition operate (turn on) from an Lr20 battery, which is included with the device itself. The fact that this water heating device is an “automatic water heater” is evidenced by the article “ i" in the name of the model with ionization control of flame combustion.
These gas water heaters are produced different power and hot water performance. The Baxi SIG-2 11i model has a rated power of 22 kW and a flow rate of 11 liters per minute. Baxi SIG-2 14i dispenser with electronic ignition: 29 kW and 14 l/min., respectively.
Automatic models of this series have a small LCD display on the front side of the case that displays the set and current water temperature and error codes for any malfunctions or malfunctions in the operation of the instantaneous gas water heater.
Also on the column body we can see two mechanical regulators: water temperature and pressure. The temperature of the water passing through the heat exchanger is maintained automatically, and is exactly the one set by the user.
The Baxi gas water heater with manual piezo ignition is represented by one single model Baxi SIG-2 11p with thermoelectric combustion control. Manual ignition on this device is carried out thanks to a special piezoelectric element and a regulator-ignition button on the water heater panel.
This is the most inexpensive model in the line of speakers of the Italian concern, which does not have a digital information LCD display and batteries. It is produced with a rated power of only 22 kW and a capacity of 11 l/min.
Now let's see how the abbreviation " SIG-2»:
S - water heater;
I—instant (flow);
G - gas;
2 - second generation.
Geyser Baxi SIG-2: price, design and functionality
Baksi gas water heaters are produced in Iran at the same manufacturing plant as the Italian brand water heaters. The internal structure, arrangement of components and elements are almost identical. And even the price is approximately the same: from 12,000-13,000 rubles for the most inexpensive model. Let's look at the internal structure of the Baksi gas water heater in detail using a photo diagram.
Gas water heater device Baxi automatic
1 - traction sensor;
2 - chimney;
3 - copper heat exchanger;
4, 15 — ignition burner;
5 — stainless steel gas burner;
6 - hydraulic valve;
7 — water temperature regulator;
8 - gas valve;
9 — fitting for gas connection;
10 — gas pressure regulator SETAAK;
11 — electronic unit;
12 — battery compartment;
13 — economizer;
14 — pipe for measuring pressure;
16 - temperature sensor.
Characteristic features of the Baxi SIG-2 models are the presence of a high-quality copper heat exchanger for heating water, a brass hydraulic group and gas burner made of stainless steel.
In addition, all models are equipped with continuous, smooth modulation of the burner flame, separate regulation of water temperature and set power, as well as a built-in gas pressure reducer. Combustion control in models with auto-ignition Baxi SIG-11i and 14i is carried out by an ionization electrode, and in the model with a piezoelectric element Baxi SIG-2 11p - using a thermocouple.
Gas water heaters Baxi SIG-2: technical specifications, dimensions
The gas instantaneous water heater has compact dimensions, the 11 liter model: 582x314x245 mm, and the 14 liter model: 650x365x245 mm. The chimney diameter of the columns is 110 and 130 mm, respectively.
Water and gas connections are made using 1/2″ threaded fittings. Baksi geysers can operate on both natural and bottled gas (by replacing the nozzles of the appropriate gas passage diameter). Now let's look at the main characteristics in detail: gas consumption, minimum pressure water and gas and other parameters according to the table.
Gas water heaters Baxi SIG-2: technical specifications
Advantages of geysers Baxi SIG-2:
- quality of materials and internal elements;
— copper heat exchanger;
— water-gas unit made of brass;
— smooth modulation of the burner flame;
- a well-known European brand.
Disadvantages of Baksi geysers:
- narrow model range;
— a small number of customer and specialist reviews;
— price.
Today we sorted out geysers Baksi, technical characteristics, device and functional features according to the operating instructions. The Baxi SIG-2 11i, 14i and 11p models undoubtedly stand out good quality, innovation and modern design. We examined the main advantages and minor disadvantages of gas instantaneous water heaters from the popular European manufacturer Baxi. Let's watch the video.
