car alarm Sherkhan 5 User Manual

MAGICAR V

User guide

PURPOSE

The Sherkhan 5 system is a car alarm with the ability to control via radio using a key fob-communicator with a liquid crystal display. The system exchanges information between the key fob-communicator and the processor unit at a distance of up to 1500 m. Sherkhan 5 has a function for automatically starting the engine by commands from the key fob or by commands from the internal timer. The system is designed to work on gasoline or diesel vehicles with a fuel injection system and an on-board network voltage of 12V. The protection of the processor unit, shock sensor, call sensor, antenna unit is made according to the IP-40 standard and provides for installation in the car. The siren is IP-65 rated and can be installed in the engine bay away from the exhaust manifold and high voltage systems.

Keyfob communicator functions

• Multifunctional, 4-button LCD keychain communicator
• Protection against interception of MAGIC CODE code packets
• Audiovisual confirmation of executed commands
• Vibrating bell
• Loud beeps
• Ultra long distance communication up to 1500 m with processor unit
• Automatic display backlight
• Low battery indication
• Voltage indication battery car
• Indication of temperature in the passenger compartment
• Current time indication
• Indication of engine operating time in automatic mode
• Remote engine start
• Programming the engine start time (accurate to the minute)
• Sound and visual alert reminder mode
• Operational, from the key fob, programming of all system functions
• Economy Power (one AAA element)

Processing unit functions

• Automatic engine start for vehicles with automatic or manual transmission
• Operation of the starting system with both petrol and diesel engines
• Operation of the starting system with engines having a turbine
• Starting the engine on command from the key fob
• Automatic engine start every 2 hours
• Automatic engine start at a pre-set time every 24 hours
• Monitoring the engine start by signals from the generator or by noise in the on-board network
• Personal code for access to the car interior if the key is lost
• Power output for controlling the car's central locking
• Trunk release power output
• Alarm control power output (two circuits)
• Programming the lock relay type
• Auto arming (programmable function)
• Sound warning before automatic arming
• Automatic return to armed mode if the door was not opened
• Sound warning before automatic return to armed mode
• Armed mode without siren signals
• Two universal programmable control channels for additional devices
• Ability to connect negative and positive door sensors
• Input for negative trunk sensor
• Locking and unlocking the door locks when starting and stopping the engine
• Possibility of arming with and without confirmation siren signals
• Alarm warning about open door(programmable function)
• Panic or JackStop mode
• Highly sensitive two-level shock sensor with sensitivity adjustment
• Function " Free hands"for automatic arming/disarming when the owner moves away/approaches the car
• Dual mode hands-free function
• Parking lights not switched off warning

TECHNICAL PARAMETERS Sherkhan 5

Alarm types:

Influence on the main and additional electrical equipment of the car

Control methods

• Remotely with a radio frequency transmitter (key fob) at a frequency of 433.92 MHz ± 0.2% with a power of not more than 10 mW
• From the ignition key
• Automatically based on signals from sensors

Electrical circuit protection

Fuses. (Automotive slow-acting fuses according to wiring diagram)

Spheres of protection

Other options

Batteries

* The table shows the average value. The service life of the key fob battery depends on the intensity of use of the key fob and the quality of the battery, the key fob operation modes.

ATTENTION!

Use only quality batteries. Battery Application Low quality can lead not only to a reduction in the life of the key fob, but also to its damage.

KEYFOB COMMUNICATOR

Preparing the key fob-communicator for work

Before using the key fob, you must bring it into working condition, because. during transportation and storage, an insulating gasket is installed between the contact of the battery and the contact plate of the key fob, which prevents the battery from discharging before operation. Before using the key fob, remove it. To do this, release the battery compartment cover lock, press the cover and slide it in the direction opposite to the antenna. Remove the battery. Remove the insulating pad between the battery and the collector plate. Install the battery back, observing the polarity indicated on the bottom of the battery compartment. If there is no indication of the polarity of the battery, then it is set with a negative terminal towards the antenna. Close the battery cover. Keyring is ready to go.

Symbols on the keyfob-communicator display

	Timer start indicator
	TURBO mode indicator
	Passive arming indicator
	Hands-free mode indicator
	Siren indicator
	Shock sensor off indicator
	Vibrating alert indicator
	Indicator of turning on the automatic control of the central lock by ignition
	Door open indicator
	Trunk/hood open indicator
	Shock sensor alarm indicator (optional sensor)
	Car owner call indicator
	Engine running indicator
	Ignition on indicator in security mode, indicator of side lights not switched off
	Key fob transmitter operation indicator
	Battery discharge indicator of the key fob-communicator
	VALET mode indicator
	Locking and unlocking indicator. Security Mode Status Indicator
	Clock indicator, car battery voltage, interior temperature, engine warm-up time during automatic start

Purpose of the buttons of the key fob-communicator Sherkhan 5

Example notation:

I - quick (0.5 sec.) button press
I- - long (2 sec.) button press
(I + II) - fast (0.5 sec.) simultaneous pressing of the buttons (combination of buttons)
(I + II) - - long (2 sec.) simultaneous pressing of the buttons (combination of buttons)

Note: Sherkhan 5

With a long 2 sec. pressing the I button, the modes change sequentially in the order (1) > (2) > (3) > (1) … . In mode (2), the "Hands free -" function has a high range work- symbol blinking.

Setting the time on the keyfob-communicator display

Setting the current time is required before starting the operation of the system or when changing the key fob battery. Follow the steps according to the table below.

ATTENTION!

Setting the correct time is necessary condition for correct operation automatic start of the engine by timer.

Setting the keyfob-communicator, vibration call, owner call, temperature display standard "°F" or "°С"

To set the desired key fob operation mode, follow the steps in accordance with the table below.

Note: STEP 2 must be completed within 15 seconds. after STEP 1.

Arming [Button (I)]

Close doors, hood, trunk. Briefly press button I on the key fob. The system will switch to the armed mode, the door locks will be locked, the starter (ignition) interlock will turn on until the system is disarmed.

When arming:

Enable sensors:

1. Immediately after the LED starts flashing, the system begins to monitor the status of the doors, hood, trunk, call sensor of the owner of the car.
2. The shock sensor will turn on after 30 seconds. after arming.

Note:

If, when arming, you heard three signals from the key fob, and on the display for 5 seconds. the image of an open door or trunk flashes, this means that the door, hood / trunk is open in the car. The door, hood/trunk sensor will be immediately armed when its functionality is restored.

The hood area is not displayed separately, the hood sensor must be connected to the trunk sensor wire.

Disarming [Button (I)]

When the system is armed, briefly press button I on the key fob. The system will be disarmed, the door locks will be unlocked, the starter (ignition) interlock will be disabled.

When disarming:

HANDS FREE function [Button (I)-]

ATTENTION!

The "Hands free" mode works only when using a keyfob-communicator with a liquid crystal display; when using optional keyfobs without a display, this mode is not available.

When you press button I of the key fob-communicator for 2 sec. You can turn Hands Free on or off. When the "Hands-Free" function is enabled, the system will automatically arm itself when you are 15-35 m away from the car with the key fob-communicator*. or is removed from the security mode and unlocks the door locks when approached. The function has two modes of operation:

In the first mode, the mark on the display does not blink and the range of the function is minimal.

In the second mode, the mark on the display with the inscription "AUTO" flashes and the range is maximum.

The change of operating modes takes a long 2 seconds. by pressing the I button next order: (Function on, mode 1) > (Function on, mode 2) > (Function off) > (Function on, mode 1)….

Arming/disarming will be accompanied by a melodic signal from the key fob-communicator.

Continuous use of the "Hands free" function is not recommended, as its use dramatically reduces the battery life of the key fob.

* Note:

The distance from the unit to the key fob-communicator, at which the system makes a decision to arm or disarm, can vary and depends on a group of objective reasons: relative position antennas of the key fob-communicator and the antenna unit, the presence of metal objects near the antennas, from radio interference on the air, weather, etc. ...

When the hands-free function is enabled:

Mode change is accompanied by one signal from the key fob-communicator.

When the HANDS FREE function is turned off:

Starting the engine on command from the key fob [Button (II) -]

To start the engine, press button II on the key fob for 2 seconds. The system will be armed, the door locks will be locked, the car engine will start. After the engine has started, the keyfob-communicator displays information about the time remaining until the end of engine operation in automatic mode. Engine run time is programmable and can be 15/25/45/5 minutes (programmable function 2-4). To start driving. You need to open the door, insert the ignition key into the lock and turn it to the "ON" position. To do this, you have 20 seconds, after this time the system will transfer control to the ignition switch, if you do not turn on the ignition, the engine will be stopped.

If the launch did not occur the first time, the system will try again. The system makes no more than three attempts to start, after which it goes into standby mode. If the car engine does not start after the last attempt, contact a service station to diagnose your car.

At the time of launch:

The system will not start the engine if:

• Ignition on
• The car engine is already running
• Door or hood/trunk open
• Backup mode failed for vehicles with manual transmission

On successful launch:

Note: If the car's engine is started automatically, the current time indicator shows the time remaining until the engine is stopped. Time is displayed in countdown mode. Time display format in this mode: [ XX min: XX sec.]

When the engine stops automatically:

Trunk opening [Button (III)-]

Press and hold for 2 sec. key fob button III, after which the trunk will open. If the system is armed (doors locked), it will disarm, the doors will unlock, and the starter will be disabled. To implement this function, it is necessary to have a trunk lock solenoid connected to the corresponding output of the main unit of the system.

When opening the trunk:

Checking System Status [Button (IV)]

If you need to check the status of the system, briefly press the button IV of the keyfob-communicator. Information about the state of the system will be shown on the keyfob-communicator display, as well as confirmed by siren and alarm signals.

When checking system status:

When checking the status of the Sherkhan 5 system, the current time indicator shows the temperature in the car. The temperature can be displayed in either °F or °C.

The temperature inside the car is 10°C.

Repeated short pressing of the button IV of the keyfob-communicator within 6 seconds after the first one allows you to view information about the car battery voltage in volts.

The voltage on the car battery is 13.9V.

Panic or JackStop mode (anti-seizure) [Button (IV)-]

When you press the button IV of the key fob for 2 seconds. The system will enter the "Panic" mode or JackStop mode (protection against seizure) - programmable function 1-4.. If the system was disarmed, it will arm itself, the door locks will be locked. The siren will sound for 90 seconds, alarm- flash for 90 sec. The "Panic" mode stops the automatic engine start mode. After 90 sec. the system will go into armed mode until it is disarmed by the key fob or emergency shutdown mode. Panic mode can be stopped by briefly pressing the I button. Panic and JackStop modes are used in case of danger or when it is necessary to draw attention to the car.

When activating the "Panic" and JackStop modes:

Differences in the "Panic" and JackStop algorithms (depending on the selected value of the programmable function 1-4):

ATTENTION!

Jack Stop Mode can only be used in emergency cases. It is not a regular constantly used CCTTC mode. it provides for stopping the engine while driving.

When choosing one or another mode, consult with a specialist.

Siren Silence [Button (I+II)]

By briefly simultaneously pressing the buttons I + II of the key fob, you can turn on or turn off the siren signals. In this case, the key fob signals and alarm signals will work as usual. The siren activation is indicated by the presence of a symbol on the key fob display.

When the siren is turned on:

When turning off the siren signals:

VALET Mode [Button (I+III)] Sherkhan 5

To disable the security functions of the system and when transferring the machine to a service station for maintenance, you can use the VALET mode. To do this, briefly press the buttons I + III of the key fob.

In VALET mode, you can control the locking and unlocking of the door locks. To lock or unlock the locks, briefly press button I.

The VALET mode is shown on the display with the symbol

To exit the VALET mode, briefly press the buttons I + III of the key fob

When VALET mode is enabled:

When turning off VALET mode:

Disabling the two-level shock sensor [Button (I + III)] Sherkhan 5

You can disable the two-level shock sensor. Simultaneously press and hold for 2 seconds. buttons I + III of the keyfob, as a result, the sensors will be turned on or off. The indication of the sensor disconnection is the symbol on the key fob display. Switching off the sensor is necessary if you leave the car where false alarms are possible (the car is parked near tram tracks, a child or an animal remains in the car).

When the shock sensor is disabled:

When the shock sensor is turned on:

The shock sensor is called two-level, because it has two levels of response from the impact on the car.

In case of a weak impact, the system warns with 4 short siren sounds and 4 alarm flashes. Key fob - communicator gives a short tone signal, the symbol of impact on the car flashes on the display. If the impact is strong, the system goes into alarm mode for 30 seconds.

Central locking control for turning the ignition on and off [Button (I + IV)]

By briefly simultaneously pressing the buttons I + IV of the key fob, you can turn on or off automatic control central locking (CL) for turning the ignition on and off. If the function is enabled, the door locks will be automatically locked after 30 seconds. after the engine is started and all doors, the hood/trunk will be closed. The locks are unlocked immediately when the ignition is switched off. The function activation is indicated by the presence of a symbol on the key fob display.

When the central locking control function from ignition is turned on:

When the central locking control function is turned off from the ignition:

Passive Arming [Button (II+III)] Sherkhan 5

The passive arming function can be turned on/off by briefly pressing the P+S buttons on the key fob. When passive arming is enabled, the system will automatically arm itself after 30 seconds. after closing the last door or after disarming with the key fob. The system warns of passive arming with alarms and (or) siren every 10 seconds. If within 30 sec. doors (hood/trunk) were opened, the system will arm itself in 30 seconds. after closing the doors (hood/trunk).

When passive arming is enabled:

When turning off passive arming:

Setting the timer for automatic engine start [Button (II+IV)]

Briefly press the buttons II + IV of the key fob to turn the engine start on or off by timer. The indication of the inclusion of starting the engine by timer is the presence of the label "TIMER" on the key fob display. The system provides two modes of starting the engine by timer. The first mode allows you to start the engine every day in advance set time, the second mode allows you to start the engine periodically, every 2 hours to warm up (or cool the interior in countries with a hot climate). Two modes cannot be used at the same time, the mode you need can be selected by programmable function 2-3 .

To automatically start the engine on a timer in right time(24h) you need to make a reservation for this mode. For this:

1. Select start time (see table)
2. Press the buttons II + IV and turn off the label "TIMER"

In order to enable or disable the engine start by timer every 2 hours, briefly press the buttons II + IV of the key fob. Setting the start time in this mode is not required, the first engine start will occur 2 hours after the mode is turned on.

When the timer engine start is enabled:

When turning off the engine start by timer:

Note: Automatic start of the engine on a timer every 24 hours is useful for starting the engine daily in certain time if your car is parked outside the range of the key fob.

ATTENTION!

The engine start time according to the 24 hour timer can be shifted up to ±2 minutes per day.

TURBO Mode [Button (II+IV)]

If the car has a Turbo - engine, then after long work at high speeds it is not recommended to stop it immediately. The engine should idle for some time to cool the turbine. For this, the SCHER-KHAN MAGICAR V system has a TURBO mode (turbo timer). If the TURBO mode is on, then at the end of the trip the engine will run for 2 minutes. To enable or disable the TURBO mode, briefly press the buttons III + IV of the key fob.

When TURBO mode is enabled:

When turning off the TURBO mode:

To activate the mode at the end of the trip, do the following:

1. Put the gear lever in neutral or "P" position.
2. Turn the ignition key from the ON position to the OFF position. The engine will continue to run after this for another 2 minutes.
3. Get out of the car, close the doors. As soon as the doors are closed, the alarm will flash

Now you can arm the system. The engine will then run until the expiration of 2 minutes. interval. When the car is armed, the door, hood/trunk sensors, the driver call sensor are immediately armed, and the shock sensor will start working after the engine stops. The engine will be immediately stopped when the door, hood/trunk sensor is triggered, and the system will go into alarm mode. If necessary, you can urgently stop the engine by pressing for 2 seconds. key fob button II.

Auxiliary channel 1 control [Button (II)]

If your car is equipped with an electromechanical hood lock, an additional preheater or other service equipment, you can control the operation of these devices using a key fob. To do this, briefly press button II on the key fob. A short or long signal will appear at the output of additional channel 1 of the processor unit (programmable function 2-5). The siren and parking lights signals will differ when controlling an additional channel, depending on the state of the programmable function 2-5. If a channel is programmed for a long tone (Programmable Function Value 4 2-5), the system will confirm its activation and deactivation with siren and alarm signals. If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel. The additional channel does not work in the VALET mode and in the alarm mode.

Turning on an additional channel:

Note: If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel (programmable function 2-5)

Auxiliary channel 2 control [Button (III)]

If your car is equipped with an electromechanical hood lock, an additional preheater or other service equipment, you can control the operation of these devices using a key fob. To do this, briefly press button III on the key fob. A short or long signal will appear at the output of additional channel 2 of the processor unit (programmable function 2-6). The siren and parking lights signals will differ when controlling an additional channel, depending on the state of the programmable function 2-6. If a channel is programmed for a long beep (Programmable Function Value 4 2-6), the system will confirm its activation and deactivation with siren and alarm signals. If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel. The additional channel does not work in the VALET mode and in the alarm mode.

Inclusion of an additional channel: Sherkhan 5

Turning off the additional channel:

Note: If a short signal is programmed at the output of an additional channel, the system will only confirm the inclusion of the channel (programmable function 2-6)

Alarm mode

If the door, hood/trunk is opened in armed mode, the system will go into alarm mode for 30 seconds, alarms and sirens will last 30 seconds. At the end of 30 sec. the system will return to armed mode. If the shock sensor alarm zone is triggered (strong impact), the system will go into alarm mode for 15 seconds, the alarm and siren signals will last 15 seconds. At the end of 15 sec. the system will return to armed mode. When the warning zone of the shock sensor is triggered (weak impact), the system will not go into alarm mode, but will only issue a series of four short signals by a siren and an alarm. You can stop the alarm mode by short pressing the keyfob button I. The locks will not be unlocked, and the system will switch from alarm mode to armed mode.

In alarm mode:

Reminder mode

If the communicator keyfob received an alarm signal from the door, hood/trunk, shock sensor, call sensor and you did not notice it immediately, then the keyfob, after transmitting the alarm signal, goes into reminder mode (short beeps and indication of the zone that caused the alarm mode) . To stop the reminder mode and check the state of the car, briefly press the button IV of the key fob or button I to exit the security mode and unlock the door locks.

In reminder mode:

Note: Keyfob communicator does not go into reminder mode when receiving a warning signal from a shock sensor (weak impact)

Car Owner Call

If you need to call the owner of the car, tap with a hard object (coin, keys, etc.) near the call sensor. The call sensor LED will flash in green. The function of calling the owner of the car is available immediately after arming. To stop the signals of the keyfob-communicator, press the button I of the keyfob. To stop the signals from the keyfob-communicator and check the condition of the car, briefly press the IV button.

When calling the car owner:

Access to the car without a key fob Sherkhan 5

Access to a car without a key fob may be required in a number of cases. For example, if the key fob is lost, if the battery in the key fob is dead, if you are relaxing on the beach and do not want to take the key fob with you (the key fob and keys are closed in the car). The SCHER-KHAN MAGICAR V system provides such an opportunity. To ensure that only you are allowed access, the system uses a personal code consisting of four digits. The value of each digit of the code can vary from 1 to 9. Thus, the code can have a value from 1111 to 9999. The code is entered and recorded through the call sensor of the car owner.

Recording a personal code:

In order for you to use this function, you must enter your code into the system memory. To do this, follow several steps:

1. Turn on the ignition
2. open the door
3. While the LED is flashing, tap the call sensor the number of times corresponding to the first digit of the code. After 1.5 sec. the LED will confirm the selected number with red flashes and start flashing again.
4. While the LED is flashing, tap the call sensor the number of times corresponding to the second digit of the code. After 1.5 sec. the LED will confirm the selected number with red flashes and start flashing again.
5. While the LED is flashing, tap the call sensor the number of times corresponding to the third digit of the code. After 1.5 sec. the LED will confirm the selected number with red flashes and start flashing again.
6. While the LED is flashing, tap the call sensor the number of times corresponding to the fourth digit of the code. After 1.5 sec. The LED will confirm the selected number with red flashes.
7. You will hear one siren tone to confirm that the code has been programmed, and the alarm will flash once.

If you made a mistake on any of the steps, then you need to record the code, starting from step 1.

Entering a personal code:

1. Tap the call sensor 10 times. Each time the LED in the sensor will flash green. The time between blows must be less than 1.5 seconds.
2. The LED will quickly flash red to confirm that the previous step has been completed. If the LED does not flash red, then start from step 1 again.
3. While the LED is flashing, tap the call sensor the number of times corresponding to the first digit of the code. After 1.5 sec. the LED will confirm the entry of the first digit with red flashes and start flashing again.
4. While the LED is flashing, tap the call sensor the number of times corresponding to the second digit of the code. After 1.5 sec. the LED will confirm the entry of the second digit with red flashes and start flashing again.
5. While the LED is flashing, tap the call sensor the number of times corresponding to the third digit of the code. After 1.5 sec. the LED will confirm the entry of the third digit with red flashes and start flashing again.
6. While the LED is flashing, tap the call sensor the number of times corresponding to the fourth digit of the code. After 1.5 sec. the LED will confirm the entry of the fourth digit with red flashes.
7. If the code is entered correctly, the system will disarm, the door locks will open, and the key fob-communicator will receive a signal to disarm the system. If the code is entered incorrectly, then the key fob will receive a call signal from the owner, and it will be necessary to repeat all the steps starting from step 1.

The system allows five attempts to enter the code within 30 minutes. If the code was entered incorrectly, then its entry is blocked for 24 hours or until you disarm the system using the key fob.

Battery protection (out-of-dimension warning)

The system helps protect the car's battery from being discharged. If you forgot to turn off the parking lights, then when arming, the key fob-communicator will give a series of beeps for 5 seconds. At this time, the images of the lock and side lights will flash on the display. The warning tone will repeat every 30 seconds. three times.

Starter or ignition lock

The system in armed mode will not allow you to start the car engine. When you try to start the engine in armed mode, the system will send an alarm signal to the key fob communicator. An alarm about turning on the ignition will be displayed by flashing side lights on the key fob communicator, sound and vibration signal. The engine blocking operation mode is selected when the system is installed at a service station and depends on the values ​​of two programmable functions 1-4 and 1-8. You can find out more about blocking the engine of your car at the place where the system is installed. When the starter interlock is selected, the system will prevent the vehicle's starter from restarting if the engine is started in automatic mode.

Open door warning

The system warns of an open door (programmable function 1-2). When a custom function value is selected, the alarm flashes if the car door is open.

Protection of the radio channel from code interception

The system has special protection for the commands transmitted by the key fob. Each time you press a button on the system's key fob, the code message changes according to a special algorithm. This is done to protect the system from interception of the code and its selection (intelligent hacking of the security system). The code protection algorithm is specially designed for the SCHER-KHAN MAGICAR system and is unique, not applicable in one security system of other brands.

Motor protection in automatic start mode

The system in automatic start mode constantly monitors the operation of the engine. If the engine stops before the end of the warm-up cycle (engine failure or out of fuel), then no later than 20 seconds. processor unit system will turn off the ignition. Repeated automatic start of the engine will not be possible until the malfunction is eliminated. For vehicles with a manual transmission, you must perform the backup mode again.

Shock sensor sensitivity adjustment

You can adjust the sensitivity of the shock sensor depending on your requirements. A regulator is provided to adjust the sensitivity of the sensor. Turning the knob clockwise increases the sensitivity, and counterclockwise decreases it until the sensor turns off. Consult a service station about the location of the shock sensor, it must be easily accessible for adjustment.

Adjusting the sensitivity of the owner's call sensor

You can adjust the sensitivity of the car owner's call sensor depending on your requirements. To adjust the sensitivity on the sensor, a step regulator with three positions is provided. The extreme left position of the regulator corresponds to the minimum sensitivity of the sensor, the extreme right - to the maximum. The sensor should be located in the lower corner of the car's windshield.

Adjusting the volume of siren confirmation signals

You can adjust the volume of the siren's short beeps. To reduce the volume, you need to cut the loop from the wire on the siren's body. The system can be equipped with any siren according to the wishes of the owner, including those where there is no possibility of adjustment.

Backup mode (only for manual transmission)

The standby mode excludes the possibility of automatic starting of the engine if the manual transmission lever is not set to the neutral position. Depending on your requirements, you can choose one of three redundancy algorithms (programmable function 1-6).

Algorithm 1

Algorithm 2

To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:

1. At the end of the trip, without turning off the engine, place the gear lever in neutral position
2. Close the hood/trunk doors
3. Remove the key from the ignition switch (in the OFF position). The engine will keep running
4. Open the door and get out of the car. Close the door. The engine will stall.

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, redundancy will be prohibited if the door, hood / trunk are open at the time the ignition is turned off.

Algorithm 3

To perform a backup (prepare the vehicle for the subsequent automatic start of the engine), do the following:

1. At the end of the trip, without turning off the engine, place the gear lever in neutral position
2. Close the hood/trunk doors
3. Press for 2 sec. key fob button II
4. Remove the key from the ignition switch (in the OFF position). The engine will keep running
5. Open the door and get out of the car. Close the door. Engine will stall

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnosis of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no backup mode and automatic engine start will not occur. In this algorithm, the implementation of the reservation requires you to each time press button II of the key fob before turning off the ignition (by turning the key in the ignition switch to the OFF position).

ATTENTION!

Close the sunroof and windows before leaving the vehicle. Do not leave people or animals in the vehicle when the reservation mode is being executed.

Do not start the engine automatically if there are people or animals in the car.

Leave the gear lever always in the neutral position. Do not use automatic engine start on open top vehicles.

If the operation of the redundancy mode differs from the described algorithms or does not occur, urgently contact a service station for advice. Until the cause is removed incorrect operation do not use automatic engine start.

PROGRAMMING NEW KEYFOBS

The system can remember the codes of three key fobs. To program new key fobs, follow two steps.

1. Turn the ignition key three times from OFF to ON. The alarm will flash once to confirm entry into programming mode.
2. Not later than 4 sec. after the alarm flashes, press button I of the key fob, the code of which must be entered into the memory of the processor unit.

To exit the programming mode, do not take any action for 4 seconds. after writing the code of the last key fob.

If no action is taken after step 1, then after 4 seconds. the alarm will flash 2 times, the system will switch from the key fob programming mode to the VALET mode.

Note:

The system has three memory cells for storing key fob codes. When you try to write the fourth key fob, the code of the first recorded key fob will be deleted.

PROGRAMMING FUNCTIONS USING THE KEYFOB

Programming the CTCTS functions using a key fob consists of four steps.

1. Entering the programming mode and selecting the programming menu. To enter Menu No. 1, press the I + II buttons simultaneously for 2 seconds. To enter Menu No. 2, press the I + IV buttons simultaneously for 2 seconds. The siren will sound one short beep and the alarm will flash once, confirming the successful completion of STEP 1.
2. Press the IV button to select the Menu function you want to change. The number of presses must correspond to the number of the selected function. For example, to select function 4, you need to briefly press the keyfob button IV four times. Each button press will be confirmed by a short siren tone (if enabled) and an alarm flash.
3. Wait a few seconds. The system will confirm the number of the selected function to be changed with short siren sounds and alarm flashes. The number of signals will correspond to the number of the selected function.

   Note:

   If, when choosing a function, you made a mistake with the number of clicks and (or) there are no siren and alarm signals, then you need to repeat all the actions starting from STEP 1.

4. Press the I button to select the factory setting for the function. To confirm this, the siren will give one short signal, the alarm will flash once. Press the II, III, or IV button to select optional function values. To confirm this, the siren will give two, three or four short beeps, the alarm will flash two, three or four times.

Note:

If you hear one long siren signal, this means the system has exited the function programming mode. To continue programming, repeat all steps from STEP 1.

ATTENTION!

If you need to change more than one function from the Menu you have selected, then the selection of each function to change must begin with STEP 1.

Menu of programmable functions

Menu #1 [Button (I+II)-]

Note on function 1-4: This function allows you to select the "Panic" mode or JackStop mode (protection against robbery):

Resetting all programmable functions of Menu No. 1 to factory defaults

1. Entering programming mode. Press buttons I+II simultaneously for 2 sec. The siren will sound one short beep and the alarm will flash once, confirming the success of STEP 1
2. Briefly press button III on the key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time, three siren sounds will sound, the alarm will flash three times, confirming the factory settings of all menu 1 programmable functions.

Menu #2 [Button (I+IV)-]

Setting all programmable functions of menu No. 2 to factory values ​​Sherkhan 5

To reset the programmable features to factory defaults, two steps are required.

1. Entering programming mode. Press buttons I+IV simultaneously for 2 sec. The siren will sound one short beep and the alarm will flash once, confirming the success of STEP 1
2. Briefly press button III on the key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time after this, three siren sounds will sound, the alarm will flash three times, confirming the factory settings of all programmable menu #2 functions.