How to finish the door with dermantine. How to sheathe a door with dermantine with your own hands? A special way for the lazy

The choice of a door is a responsible matter, because it must protect the room from outsiders, have good soundproofing characteristics and not let heat through. It is these indicators that a wooden or metal door, sheathed and insulated with special materials, has.

The cost of a sheathed product is an order of magnitude higher than the cost of a conventional door leaf, so not everyone can afford it. In order to save money, you can sheathe the door yourself, since this method is quite simple and inexpensive. As an incentive prize, you will receive a reliable insulated door that does not let in excess noise.

Leatherette is most often used as a sheathing material due to its unpretentiousness.

Sheathing leatherette

The choice of leatherette is a simple matter, because there is a significant difference between domestic and foreign manufacturers no, except in their cost. When buying, you only have to decide between ready-made kits, including fasteners and foam rubber, and independent choice all the necessary details. When buying leatherette by the footage, please note that for a wooden door it is necessary to take a segment 15 cm wider than the door leaf, and for a metal one - 12 cm.

As a heater, it is recommended to use foam rubber, the thickness of which should not exceed 1-2 cm. You can also try to insulate the door with isotone, which has slightly higher performance than foam rubber can boast, but its cost is not low.

Note! As fasteners, special nails with a wide head are used.

The color of the head is selected to match the material chosen for the sheathing. For attaching leatherette to metal doors, Moment glue is used.

Kit necessary tools includes:

brush;
scissors;
construction stapler;
pliers;
a hammer;
screwdriver.

Wooden doors

Upholstery of doors takes a little time, so there should be no problems, especially if you strictly follow the action plan below.

We remove the door from the hinges, after which we unwind the fittings. The canvas, freed from unnecessary details, is laid on a flat surface.
We remove the remnants of the old upholstery, if any.
The lining material is attached to the wooden canvas with a stapler, although ordinary nails can also be used for fixing.
It is necessary to cut off the leatherette taking into account the release of 15 cm in width.
Turn the top edge over and fasten, evenly distributing the material. Now we are doing the same with leatherette on the sides, but at the same time on both sides, in order to gradually stretch the free material.
The lining insulation must be laid so that it protrudes slightly on the spare edge, which will make it possible to make a small roller when bending the sheathing material. The resulting roller should protrude 5 cm beyond the doors. We fix it all with the selected fasteners.
We make the same roller on the sides of the door leaf. In this case, it is necessary to monitor its thickness, which should be the same along the entire length of the upholstery.
When fixing the skin, make sure that there are no wrinkles that occur when the tension is insufficient.

Now you can start decorating appearance skins. Using the selected braid and nails, we form a specific pattern that you choose yourself. Most often it is a rhombus or a square. The decorative braid is stretched from one corner to another and fixed crosswise with nails on the sheathing material.

If leatherette for one reason or another moves away from the door, then it can be fixed with a horizontally stretched band. Fasteners are recommended to be placed at a distance of 10 cm.

Note! The lower roller should be at a distance of 15-20 mm from the floor.

At the final stage, it remains only to arrange all the accessories in their places. The upholstery of the doors is over - admire the result.

metal

Sheathing material is attached to metal sheet with glue. Consider the order of this operation.

Glue is applied along the edges of the door leaf, after which foam rubber is attached to it. Peeping edges of the material are carefully trimmed with scissors.
Next, glue is applied to the end of the door at the top. It is recommended to carefully monitor the emerging folds and distortions and correct them during them so that the result satisfies you.
After the glue dries, use a clerical knife to remove excess material.
Fasten the handles and locks in place.

With these two methods, you can update the appearance of any door and improve its performance, while the cost will be minimal. By using ready-made sheathing kits, you will save valuable time, although they are a little more expensive. From pieces of material, you can make an interesting miniature and fix it on the door.

Video

You will learn tips on door upholstery technology by watching the following video:

The front door is the face of the apartment, says a lot about it. interior decoration. Often from the side of the apartment it is drawn up with the help of decorative panels, but from the outside the surface is not decorated, for fear of the actions of vandals. Such actions are fraught with the fact that the wooden surface suffers from the effects external environment, and metal - has low insulation from noise and cold.

A door that has lost its appearance is better to be updated. One of the durable ways to give an aesthetic appearance is door upholstery. It also increases noise and heat insulation in a house or apartment, which is especially appreciated by the owners of apartments on the lower floors. Upholstery is the most affordable and in a budgetary way door decoration. It does not require special care.

A new door trimmed with leather is quite expensive. good option will sew it up on his own. Every man will be able to cope with the work after studying all the stages finishing works. The incentive prize will be insulated beautiful door absorbing annoying sounds.

The most common material for door upholstery is vinyl leather (leatherette). It has a number of advantages: it does not fade under sunbeams, does not wrinkle, retains the structural pattern, looks beautiful and elegant.

Properties of vinyl leather for upholstery

To strengths faux leather include:

Long service life. The material does not lose its properties for more than 10 years.
Simple care. For cleaning, use a damp cloth, and to add shine - cream.
Moisture resistance. The material does not absorb liquids and performs well in high humidity conditions.
Frost resistance. Low temperatures do not reduce technical qualities material, its decorative properties.
Wide range of colors. On sale are various shades all colors: from dark to pastel. This allows you to easily choose the right color for a harmonious interior design.
Antiseptic properties. Vinyl leather is resistant to rot, mold and insects on the surface and inside the upholstery.
Chemical resistance. Leatherette can be washed with many household products.
Low price. The cost of door upholstery in a country house, apartment or private house will require minimal investment.

Self-finishing wooden or metal doors with leather will solve the issue of sound insulation and will prevent heat leakage from the room, the material of the doors will be reliably protected from external environmental influences.

Among the disadvantages are:

Flammability. Vinyl skin is afraid of direct exposure to flame and ignites quickly.
Impossibility of repair. Damage to the surface of the skin is almost impossible to repair, it will need to be completely replaced.
Low strength. The material is easy to cut. Upholstery requires careful handling.

Upholstery material and tools

To work, you need to purchase right amount material and some simple tool if it is not available.

At self-fulfillment finishing work requires the following tool:

a hammer;
several screwdrivers;
construction scissors and a knife;
tape measure or ruler;
glue brush;
furniture stapler and staples 0.7-1 cm.

Materials:

vinyl skin desired color and size by 5-15% more area door leaf;
lining material - batting, isolon or foam rubber;

For the first time, it is better to use plastic batting, as it provides an even distribution of the material over the entire surface. If you have upholstery experience, then you can use any material. However, in the process of work, it is necessary to constantly monitor the uniformity of distribution, excluding the formation of lumps and irregularities.

polymer glue (Moment station wagon);
decorative nails with a large hat;
decorative braid for decorating and fixing the upholstery.

There is no significant difference between domestic and foreign material, except for its cost. When buying by footage, allowance should be taken into account: 15 cm for wooden canvas and 12 cm - metal. The thickness of the seal should not exceed 2 cm.

Braid and nails should be matched to the door fittings and not violate the overall style. Fasteners can be bought by weight or packed in 100 pieces.

Today in construction stores they sell ready-made kits for leather upholstery of doors. A complete set will eliminate the likelihood of visiting a hardware store in the midst of construction work.

upholstery technology

There are several ways to upholstery doors with leather. The chosen option depends on the skills of the master, the desired effect and the material used.

Finishing can take place on the outside or inside doors, as well as on both sides at the same time.

Preparatory work

Door preparation takes place in several stages:

Remove from hinges, lay on a pair of stands that can be built from chairs or a table. The door should lie flat up on the side that will be finished.

Some masters manage to upholster the door on weight. With little experience in such work, it is better to put the door in a horizontal position.

Remove the old coating, decorative elements and accessories. Do not worry about the resulting irregularities - a layer of insulation will hide the flaws and visually level the surface. On the wooden surface it is better to apply a layer of antiseptic.
Cut out a leatherette blank, the length and width of which should be with an allowance for each side of more than 10 cm.

Creating rollers

On doors it is required to provide leather rollers that provide good insulation. Before proceeding with their manufacture, you should consider the direction of the door:

when opening from the outside, 4 rollers are required on each side;
with the inside - three is enough (the side facing the loops is not upholstered with a roller).

For an inward-opening wooden door, the fourth bead can be cut to a smaller width and nailed to the door frame and not the canvas.

To make a roller yourself, you need to cut a strip of material 10-15 centimeters wide. It is also necessary to cut a segment lining material.

One edge of the strip is fixed face down on the edge of the door. One long roller is made from the lining and covered with the second edge of the leather strip. Work begins from the upper right corner, continuing on the sides and ending at the bottom. The lower roller should not touch the floor, as abrasion will occur. It is necessary to fix the rollers with staples using a stapler. They are driven in every 20 centimeters around the entire perimeter of the door leaf. It is acceptable to use nails.

For metal door use glue, which coats the surface and evenly distributes the material, slightly pressing. The average consumption of glue is 100 ml per side of the door. Before applying the adhesive, the surface must be degreased. Next, glue is applied to the ends of the doors and the skin is pressed. Excess material is cut off with a knife.

door cover

Stretching steps:

Door insulation. A blank of paralon or batting is laid on the canvas, and covered with leather at the top. The largest allowance should be on the side of the loops.
Tuck the edges of the leatherette, hiding the edges of the insulation inside.
Fixing the canvas with nails. Start hammering decorative carnations should be from the side of the castle. They are evenly distributed over the entire area so that the seal does not slide down, forming an ugly fold at the bottom of the door. The number of nails depends on the aesthetic criteria and the type of filler. Not sheet material should be hit more often.

During upholstery for decoration, you can use fishing line or thin wire, which is pulled between the nails.

To make the close-fitting on a metal door look neat, the edges of the material are tucked and fixed with staples from the inside. Glue is applied to the lining material, folded and pressed upholstery. All work should be done slowly, gradually moving in one direction.

With a wooden door, everything is easier. The edges are folded and nailed with decorative nails in 15 cm increments.

During the fastening of the sheathing, it should be controlled that the fasteners of the rollers do not look out from under the edges of the material. A few millimeters recede from the edge of the door so that the skin does not interfere with the movement of the door in the opening.

Hardware installation

Installation of fittings takes place at the final stage of tightening. In all places of technological holes it is necessary to make small incisions on the skin and lining material. To determine the location of the cuts, it is enough to feel the old holes through the upholstery. Peephole, lock and door handle installed in the correct places.

With the help of decorative nails, you can easily make the desired pattern on the surface of the door. After all work, the door can be reinstalled on the hinges.

For better insulation, you can purchase rubber compressor and glue the perimeter of the box with it.

"Lazy" trim

This method of sheathing is not much different from the classic one. Its only advantage is that finishing can be done without dismantling the door from the hinges. The method is suitable for doors with a large mass.

Operating procedure:

Cut a canvas from a roll of leather according to the size of the door with an allowance of 15 centimeters and 4 strips on each side 14 cm wide.
A similar canvas and strips are cut out of the insulation.
Remove the door handle, lock and peephole.
Fix the insulating rollers: nail one side to the edge of the door leaf, lay the insulation and wrap the other side of the strip.
Lay the insulation, keeping an even distribution. Fasten with staples at a distance of 5-7 cm from the edge of the door leaf.
Apply leatherette on top with a minimum allowance of 5 cm. Temporarily fix on the surface of the door.
Start upholstery from the side of the castle, carefully tucking the edges and fixing with decorative nails. Pass along the entire diameter of the door. When nailing, the material is constantly stretched so that the surface is even.
To door slope fasten the fourth roller from the side with a loop.
Screw on the previously removed fittings.

Features of metal door trim

Metal doors can be upholstered in two ways. The first is democratic and consists in gluing the material to the canvas. Another option is more expensive, based on the use of special panels. It allows you to get a more beautiful appearance, insulation and will last much longer.

Budget way

It was previously mentioned that the fastening of material to metal surface done with glue. For greater clarity, let's take a closer look at the order of operations:

Glue is applied to the edges of the door and foam rubber is fixed to it. All excess material, peeking edges are cut off with scissors or a knife.
Apply glue to the top edge of the door. During operation, the formation of folds and distortions is monitored. They can only be fixed while the glue is still wet.
After fixing the skin with a clerical knife, excess material is removed.
Installing locks and handles.

Using Panels

For outer upholstery, MDF linings are used, which are made different sizes. At the end, the door will look no worse than its factory counterparts.

The inner side is upholstered wall panels, which allows you to choose the material for any interior of an apartment or house. MDF can imitate the texture of expensive wood. The only drawback is that it requires careful operation. Plastic panels simpler and cheaper, but more practical.

Stages of work:

Measure the door. Corners on the inside to increase rigidity will help you measure the depth correctly. The inner height is equal to the distance between the lower and top corners. Width - the distance between the side corners. All dimensions are required to correctly quantify timber and foam sheeting.
AT hardware store you need to purchase panels, foam, wooden beam, decorative corner with a margin of 15%.
Saw the bar into 4 parts, the width of which should be equal to the width of the door leaf. They take a bar, apply it to the door and mark the line along which the cut will be made with a pencil. Similarly, they produce with the lower part and in the middle. All 4 bars should be located at the same distance.
With an electric drill, make 16 holes for fasteners in the door: 4 holes for each bar. The diameter of the drill must match the size of the self-tapping screw.
Fasten the bars, forming a frame for attaching the panels.
Make holes for attaching decorative panels. Their number is indicated by the manufacturer in the instructions.
In the pan, make holes for the lock, handle and peephole.
Fix panels.

Upholstery on the inside:

Fasten the frame bars as described for the outside.
Cut the foam into pieces so that they lie in the space between the bars. Make holes in it for fittings.
Lay foam or other insulation, you can fix it with glue.

Attach panels. For plastic, a stapler is used, and for MDF, with kleimers.
Fasten a decorative corner around the perimeter of the door to hide the edges of the upholstery and give it a more attractive look.
Install the lock, peephole and doorknob.

Upholstery of the door with vinyl leather allows you to restore the appearance of the door on a budget, eliminate drafts and noise from landing. The work does not require special knowledge and skills, it is performed in one day. Compliance with technology and following the advice will help to quickly and beautifully finish front door, which will not only delight in appearance, but will also become an insurmountable barrier to street noise and cold air.

If you have any questions, then the stages of work can be traced on the video. The specialist will tell and show in detail all the stages of fastening the upholstery material, give valuable advice.

Of course, today, if the front door has lost its former attractiveness, the issue can be solved radically - just replace it. Fortunately, those times have passed when this procedure was really a problem due to the total shortage of absolutely everything. But… First of all, not everyone wants to part with their good, albeit already dried up and let in all sounds and smells door. Secondly, not everyone can afford the installation of a new one. What to do in this case? Breathe a second life into it - upholster the door with dermantine! With your own hands or invite a specialist. True, the first option is preferable, if only because it will allow you to save a fairly significant amount. And this, you see, is a strong argument. Therefore, arm yourself with materials, tools and knowledge on how to upholster a door with dermantine. And don't be scared. Even if you have held a hammer in your hands only a couple of times in your entire life, everything will work out! The process is very simple, you will not have any difficulties.

So let's start. We offer you a master class on the topic: "How to upholster a door with dermantine." Study, and then, with full confidence in your abilities, proceed to work.

All about dermantin

But first we need to say a few words about the upholstery, which, by the way, have been updating doors for a very long time. It is considered a type of artificial leather, but it is a more budgetary version of it. The wrong side of it is and the front side is a layer of nitrocellulose.

If we talk about him performance characteristics, it should be noted that leatherette is distinguished by strength, durability, ease of care, more than affordable cost. In addition, there is such a variety of colors and textures on sale that if you decide to upholster the door with dermantine with your own hands, you will not have any problems with the choice. On the contrary, one can choose interesting option of this material, your front door will look as good, if not better, than your neighbor's expensive, custom-made door.

What you need

Agreed with the upholstery. But since it is necessary to upholster the door with dermantine using a heater - a special lining material, then you need to stock up on them. Usually, either foam rubber or special batting is used for these purposes. As for the quantity required material, then both insulation and dermantin should be bought according to the size of your door (taking into account allowances for seams - ten to twelve centimeters on each side).

You will also need furniture nails. They are usually produced with metal hats, which can be made in various colors and stylized as silver, gold or bronze. If desired, you can also find carnations, in which the hats are upholstered with dermantine. Still to be purchased metal corners(four pieces), PVA glue.

How to upholster a door with dermantine without a tool? No way! Therefore, stock up on a screwdriver, screwdriver, hammer, stapler and scissors. You can start.

Preparatory stage

The door, of course, will have to be removed from its hinges. Then remove from it - if any - all old upholstery. Along the way, get rid of everything that can interfere with the update process: remove the lock, remove the peephole, hinges. If there are any defects on the door leaf - eliminate them. When the surface is fully prepared, you can proceed to the main stage.

How to upholster a door with dermantine

Free up space in a room or hallway, put two stools, put a door on them. Screw on the corners. They will make your structure stronger. Cut the insulation in accordance with glue and glue the foam rubber or batting. In order not to wait until the glue dries, grab the material in several places with a stapler. Then lay out a piece of leatherette on the insulation, and so that there are identical seam allowances on each side. And then tuck the edges inward, under the insulation, forming, as it were, a small roller and at the same time nailing them. Algorithm of actions: we start from the top edge, then we fix the left and right sides, the bottom - at the very end. When fixing the roller, be sure to ensure that its thickness is uniform. And be sure to drive in the carnations at the same distance from each other, otherwise your door is unlikely to look neat.

That, perhaps, is all. On this master class "How to upholster a wooden door with dermantin" can be considered finished. But still, it is necessary to mention one small detail, thanks to which the front door to your apartment will become truly exclusive.

decorative trim

To decorate the surface of the updated door, you can use special braid or cords. Of these, a drawing is laid out in the center or over the entire surface, and then fixed in the right places with carnations. And you can “depict” whatever your heart desires: a grid, vignettes, rhombuses. It's like fantasy tells you.

Now that's really all. It is possible not only with clear conscience to teach everyone how to properly upholster a door with dermantine, but also to demonstrate the result.

Wooden entrance doors are a very finicky part of our apartments. They need constant care, protection and restoration. Of course, few of us give this subject the proper amount of time and attention. That is why they often become unusable or simply lose their presentable appearance. There is not always a desire and an opportunity to replace the old wooden product to a new one.

But you can always update it with your own hands video, give it a fresh look and aesthetics, upholstered with leatherette. How to sheathe a door with dermantine? There are many video tutorials showing how to do it yourself the right way. And with a clear step by step instructions it will not be difficult to do this even for people who do not have special skills and abilities. Moreover, the result is not only outer beauty but also sound and heat insulation.

Before starting work, prepare all materials and tools. The choice of material is so great that it makes sense to think about the future design of the door in advance. Otherwise, you will walk and choose for a very long time. You will also need foam rubber 2 centimeters thick and batting, a construction stapler, a hammer, big scissors and ordinary and furniture nails. First you need to prepare the door. To do this, dismantle the door handle, peephole, hinges and all decorative elements.

Step-by-step instructions: do-it-yourself upholstery of a wooden door with dermantine video

Let's make the so-called roller, it serves as the main element of the upholstery and closes the gap between the door leaf and the jamb. Using scissors, cut a strip of leatherette 10 cm wide. Then place it wrong side up around the perimeter of the door leaf and use construction stapler attach. Instead of a stapler, you can use a regular hammer and small nails.

To avoid uneven distribution of material at fixation points door hinges it is necessary to make incisions on a strip of leatherette. Now you can start fixing the foam rubber. Lay it flat on the surface of the wooden door and secure with a stapler. Next, lay the batting on the foam layer in 2 layers. Batting is reliable protection foam rubber and protects it, increasing wear resistance and service life.

Now you can do cutting leatherette. Cut a piece of canvas the size of a door, adding 4 centimeters on each side. Lay the sheathing material evenly on door leaf and start nailing with furniture nails. You should start from the center, first at the top of the wooden canvas, then at the bottom. Remember to stretch the material well with your hand to eliminate any irregularities. Next, continue fastening the leatherette around the perimeter of the door, slightly turning the cut edges.

Now that the door already looks nice enough, it remains to finish the work with the rollers. Wrap the batting that remains after the door trim into a tube and wrap it in strips of leatherette nailed to the door at the very beginning of work. Nail the resulting roller with furniture nails in increments of 7-10 centimeters.

This completes the do-it-yourself door upholstery video. It remains only to install the peephole, hinges, door handle and everything decorative elements that were on the door earlier. Now you can enjoy not only the neat new look of the front door, but also your skill.

If you attach a little more imagination, you can use a metal thread and nails to create interesting drawing, which will give individuality to your door. In order for everything to succeed, see how to properly upholster the door leaf with your own hands video.

How do we nail rollers?

The roller is nailed to the door frame and serves as a stop for the door leaf.
At correct upholstery, the tightness of the door is taken into account. When closing, the roller should not create significant resistance, but there should not be any free space. Roller upholstery is a complex and time-consuming job that requires great experience. The installation of rollers is carried out only on wooden doors, since the fastening is made with special nails that are not hammered into the metal.
The design of metal doors initially assumes the presence of stops, seals and porches, which act as rollers. Installing a roller on a metal door is possible only if it was originally installed on the door. In the process of manufacturing a metal door wooden bars hammered into the frame, for fastening wallpaper nails. In the presence of such a design, upholstery with rollers is possible without additional refinement.

When is it impossible to upholster the front door?

After removing the upholstery, you have to deal with unpleasant surprises. Unfortunately, door manufacturers, in the fight to reduce the final cost of the product, go to all sorts of tricks to save on materials used in the production of doors. Therefore, you should not be surprised if, under the upholstery of the door, it suddenly turns out that the door is not made of a whole sheet of steel, but of strips of metal, between which they left a gap of a centimeter, or hardboard, that is, pressed paper, was used instead of metal.
Of course, such surprises will not please not only the owner of the door, but also the master who came to order, since they greatly complicate his work. Also, the inner sheet can be made of plywood. When using plywood instead of metal, the thickness of the plywood is critical. When using a thin sheet of plywood, there is simply nowhere to hammer nails. In this case, the master has to resort to pasting the door with leatherette.
Doors equipped with crossbar mechanisms may have non-separable handles for driving the crossbars. In such a situation, upholstery without dismantling and replacing the handles is impossible. Replacing handles increases the cost of the work. And in some cases, the production of work in general becomes impossible.