Glue for thermal insulation. Auxiliary materials Main technical characteristics

Specialized one-component adhesive for contact connection and fixation of insulating materials based on rubber. Possesses high efficiency and allows you to make gluing the surface in the shortest possible time.

Glue K-FLEX 414 with a volume of 0.5 liters, is one of the best adhesive composition ov in its line, due to the small volume. The lid is removed from the jar and the glue is ready for use.

The line of adhesive composition adhesive K-FLEX 414 and their volumes
√ 0.5 liters - with a metal lid. After opening, it is ready for use.
√ 0.8 liters - with a metal lid. After opening, it is ready for use.
√ 2.6 liters - with plastic red cap for large volumes of work. For use requires transfusion into an additional container.

Important! If K-Flex 414 adhesive thickens, it can be brought back to life with a K-FLEX brand cleaner.

Application
√ for connecting rubber tubes of any diameter and thickness
√ for gluing rubber rolls of various thicknesses
√ for fixing on the surface of AL Clad and IC Clad coatings.

You can send your application with the details of the payer by e-mail

Note! The price is per piece.

Do not forget to buy a cleaner with K-FLEX glue!

Glue K-Flex K-414 price

Glue k-flex k-414 0.5 lt price 434.24 rubles

Glue k-flex k-414 0.8 lt price 620.07 rub

Glue k-flex k-414 2.6 lt price 3632.54 rubles

Glue consumption
300 ml per 1 sq.m. glued surface.

TECHNICAL SPECIFICATIONS K-FLEX K-414

It was specially developed by Italian engineers for gluing foamed rubber insulation of the K-FLEX brand. Glue K-Flex 414 is resistant to ultraviolet rays. The surfaces to be glued with 414 take on the characteristics of the material itself.

Adhesive K-FLEX K414 is one-component contact adhesive based on polychloroprene rubber.

The glue is designed for bonding K-Flex thermal insulation and AlClad, InClad coatings. The optimum application temperature is 15-20 0 C. The adhesive is produced in a metal container with a volume of 0.2; 0.5; 0.8 and 2.6 liters.

When insulating cold surfaces, K-FLEX glue should be applied to the surface to be insulated and the surface of heat-insulating products. The consumption of K-FLEX K-414 adhesive in this case is 0.3 liters per m² of the bonded surface.

1. Application temperature affects viscosity and drying time.
2. High humidity affects the strength of the seam.
3. Temperatures below the dew point must be avoided.

In order to glue the seams of thermal insulation products, K-FLEX glue must be evenly applied to both surfaces to be glued. It is possible to connect the glued surfaces in 3-5 minutes. When gluing the seams, the surfaces should be pressed together tightly.

Application of K-FLEX k414 adhesive

The adhesive composition is mainly used in heating systems, water disposal, water supply, heating points. It is designed for bonding insulating materials, suitable for IC CLAD BK and SR or IN CLAD, AL CLAD coatings.

Glue K-FLEX K-414 resistant to external influences, and does not lose its qualities under the influence of temperature changes, atmospheric phenomena. The adhesive composition is resistant to aging, has long term operation. Keeps its quality characteristics at temperatures -40…+105 °C. The viscosity of the adhesive at 23 ° C can be in the range from 550 to 750 MPa, the density of the composition is 0.85 g / cu. cm.

The use of glue is allowed at positive temperatures (from 5 to 30 ° C). After applying the composition on the surface, they firmly stick together, acquire the qualitative properties of the original insulating material. The warranty period of the product is 1 year when stored at +15…+25 °C.

Glue
Installation of all brands of thermal insulation and coatings K-Flex is carried out adhesive bonding using special glue. Detailed description brands of adhesives, see below.

Very important!
Glue must be mixed before application, even if you used it yesterday.
After applying the adhesive to the material, it is necessary to withstand a short time (50-90 seconds). Glue applied to the surface of the thermal insulation will dissolve it at the micro level and begin to polymerize.
When the dried glue reaches a state similar to the sticky layer on adhesive tape, gluing can be done.
As a result of proper gluing, you will get a "cold weld" joint.

To reduce the drying time of the adhesive, as well as when gluing materials at temperatures close to 0 ° C, it is recommended to add up to 10% K-Flex cleaner to the adhesive.

.
It is not allowed to install thermal insulation on a tape without the use of glue, this is a violation of the thermal insulation installation technology.
Holding installation work detailed in the section

Purifier K-Flex consists of a mixture of solvents and is used for cleaning surfaces before applying adhesive, cleaning adhesive residues from bonded materials to give them an aesthetic appearance, cleaning tools, diluting thickened 414 adhesive or using it for gluing at slightly negative air temperatures.

Specifications

ALCLAD, ICCLADSR, ICCLADBK.

Can be successfully used for bonding thermal insulation materials based on polyethylene, for example Energoflex, Tilit, Thermaflex (Thermaflex)

K-FLEX 425 adhesive is a two-component contact adhesive based on polychloroprene rubber and filler and is intended for gluing coatings INCLAD and thermal insulation brand SolarHT.

Main specifications

Glue K-Flex 467 - winter

Contact adhesive based on polychloroprene rubber for bonding all brands thermal insulation K-Flex and coatings ALCLAD, ICCLADSR, ICCLADBK.

Main technical characteristics

K-FLEX K414 Adhesive is a one-component contact adhesive based on polychloroprene rubber for bonding K-FLEX products and AL CLAD, IC CLAD SR and IC CLAD BK coatings.

Transportation and storage:

Glue K-FLEX K-425

K-FLEX K425 Adhesive is a two-component adhesive based on polychloroprene rubber and a hardener.

Transportation and storage: At temperatures from +10 °C to +30 °C, avoid direct sun rays. It is allowed to transport products at negative temperatures, in case of freezing, the glue restores its original consistency and properties at room temperature within 24 hours, while the can must be closed. Guaranteed shelf life in original packaging is 12 months from the date of manufacture.

Adhesive K-FLEX K 467

K-FLEX K467 Adhesive is a one-component adhesive based on polychloroprene rubber. The adhesive is a "contact" adhesive and is recommended for mounting foam and synthetic rubber insulation on pipes and common surfaces located in heating and cooling systems.

Transportation and storage: At temperatures from +10 °C to +30 °C, avoid direct sunlight. It is allowed to transport products at negative temperatures, in case of freezing, the glue restores its original consistency and properties at room temperature within 24 hours, while the can must be closed. Guaranteed shelf life in original packaging is 12 months from the date of manufacture.

* - If the installation temperature is below +10 °C, please contact the specialists of K-FLEX LLC.

Products are certified. The certificate can be downloaded

Designed to seal seams protective coatings AL CLAD, IN CLAD and WHITE CLAD when placing objects outdoors.

Transportation and storage: At temperatures from +5 °С to +30 °С. Guaranteed shelf life of sealant in cartridges (0.290 l) is 18 months from the date of manufacture.

Products are certified.

The glue dispenser is designed for uniform and accurate application of glue. The main advantages are reduction of losses, reduction of the amount of working time during the process of applying glue, high speed of glue application.

K-FLEX cleaner is a mixture of organic solvents and is intended for cleaning bonding surfaces, cleaning tools (brushes, spatulas, rollers) and diluting thickened adhesive.

Available in 1 liter containers.

Transportation and storage: At temperatures from +10 °C to +40 °C, avoid direct sunlight. Guaranteed shelf life in original packaging is 18 months from the date of manufacture.

acrylic paint on the water based, odorless, easy to apply and dry quickly, does not pollute environment and does not fade. It is used to cover the insulation both indoors and outdoors, excluding UV ingress. Produced in a volume of 2.5 liters. Paint consumption 0.45-0.5 l / m 2 in two layers.

Transportation and storage:

Products are certified. The certificate can be downloaded.

Acrylic paint is water-based, odorless, easy to apply and dry quickly, no pollution and no fading. Used to coat insulation both indoors and to repair the K-FLEX COLOR system. Produced in a volume of 0.5 liters. Paint consumption 0.45-0.5 l / m 2 in two layers.

Paint color - white, gray, beige, black, green, red, blue.

Transportation and storage: At temperatures from +5 °C to +30 °C, avoid direct sunlight. Avoid freezing. Guaranteed shelf life in original packaging is 12 months from the date of manufacture.

Products are certified. The certificate can be downloaded.

Designed for punching holes in K-FLEX AL CLAD and PVC coatings for its further fixation with K-PACK rivets. Has a plastic handle.

Rivets K-PACK are made of PVC and designed for mechanical fastening of longitudinal and transverse overlaps of PVC, AL CLAD and WHITE CLAD coatings.

Packing (1000 pcs.)

Plastic clips are designed for temporary fixing of longitudinal and transverse seams of K-FLEX PE foamed polyethylene thermal insulation to ensure full adhesion of glued insulation seams to each other.
Packing (100 pcs.)

A special cap tape is needed for a neat finish on the ends insulated pipes. For ease of identification of pipes in the system, plugs are made the following types: silver, gray, red, blue. End cap length 10 m.

Example 18 x 32: where 18 mm is the length of the petals, and 32 mm is the width of the blanking tape, it is installed on the end.

Created for mechanical fixation K-FLEX plates to non-horizontal surfaces.

The assembly knife is intended for cutting K-FLEX tubular material.
Allows you to make a smooth cut without torn edges.

K-FLEX Mounting Tool Bag

Equipment:

• Universal caliper for external measurements;
• Metal compasses, at least 400 mm long, in a case or with a protective cap;
• Mounting knife, with a steel, narrow, long blade of at least 300 mm with a rounded end;
• Utility knife, 150 mm, offset blades;
• A whetstone for sharpening knives 225 mm or musat (sharpening) with a length of at least 300 mm;
• A miter box having at least three cutting angles of 22.5°, 45°, 90° and a width working surface not less than 120 mm;
• Radiator brush, with short stiff bristles, at least 38 mm wide;
• The brush is flat, with short stiff bristles, 22 mm wide;
• Lacquer marker, with a round (bullet) tip white color, with line width: 1-2mm;
• Roulette 3 meters, in a rubberized case with 3 latches.

K-Flex glue is a necessary component of the eponymous high-tech pipe insulation system. There is a plant for the production of K-Flex elastomeric products in the Moscow region. This is equipped with last word production techniques with strict product quality control.

Types of K-Flex glue

The adhesive is available in two versions:

• one-component products based on rubber;
• two-component, with inclusion of a filler.

Thermal insulation material of this brand is used:

• for isolation of pipelines in systems of heating and water supply;
• to create tight connections in air ducts.

We have on sale various packages of K-Flex glue, from 0.22 to 2.6 liters. Various forms of release allow you to purchase right amount product.

Rules for the use of glue

• use at temperatures from +5 to +30 ºС;
• thorough mixing before use;
• in case of thickening - dilution with K-Flex cleaner;
• application in a uniform thin layer on both surfaces to be glued, previously degreased and dried;
• strong compression of surfaces after connection.

The two-component composition is applied in a similar way.

Advantages of K-Flex glue

This material is in high demand among consumers due to its numerous advantages. Among them:

• economical consumption;
• reliable bonding of surfaces without changing the technical characteristics of thermal insulation;
• resistance to aging and impact atmospheric influences;
• decay resistance;
• waterproof.

Numerous studies have proven that bonded surfaces retain their properties throughout the entire period of operation, which is 20 years.

We offer to order K-Flex glue with delivery. The TERMA-MSK company is the official representative of the manufacturer, therefore it forms the most favorable prices for this product. Call to place an order!