The word “weaving” is widely used in informal communication between people, especially those associated with land plots. Yes, yes, what gardener doesn’t know how many acres of land are on his plot? The old generation remembers exactly and by heart about their three or six hundred square meters!
And although in official land documents it is required to indicate the area of plots only in hectares, especially when buying and selling, it is still more common for people to hear and count land for a garden in acres.
For interaction with cadastral authorities, the area of the plot is in hectares (ha). In this material, we propose to understand the terminology and units of land measurement, find out what a “weave” actually is and what is its relationship to a hectare.
How many square meters in one hundred square meters?
Whatever the reasons for clarifying the area of your land plot, the dimensions of which are known to you in hundred parts, the classic conversion from hundred parts to meters will take place according to the following scheme:
an area of 1 hundred square meters = 100 square meters (1 hundred square meters = 100 m2).
How to measure the area of a plot of land with a simple shape?
It is correct to start measuring by measuring the sides of the area. Having hammered pegs into the corners of the area, using a tape measure, take accurate measurements of their length and width. If the plot is correct geometric shape, then only two sides are needed - length and width. It is better to write down the measurement results in a notebook or enter them into a computer.
But if your site turns out to be asymmetrical, then you need to take measurements of all four of its sides and angles in degrees, or the length of the diagonals - also for recording.
If your garden irregular shape(NOT square or NOT rectangular plot), then the method of measuring a plot of land is a little more complicated than multiplying the length and width, but it is quite possible to an ordinary person without special education.
How to determine the size of a plot in square meters
To make the calculation as accurate as possible, you will need a tape measure, several pegs and a notepad to record the measurement results. The entire course of the required calculation follows the laws of the school geometry course, which states that for precise definition The area of a rectangular figure should be multiplied by its width by its length, for example:
- A - length, m;
- B - width, m;
- S - area, m2;
For example, if the length of your plot of land is 70 meters and the width is 40 meters, then the area can be calculated as S = 70m * 40m = 2800 m2, that is, in this case your land area is 2,800 square meters.
Considering that 1 hundred square meters is equal to 100 m2, we go the opposite way to convert the data from meters to hundred square meters. This will allow you to obtain correct results of measuring the area of a given land plot. When calculating the number of square meters in a hundred square meters, you need to divide the resulting result by 100, for example:
- plot area - 1000 m2;
- 1000 m2 divided by 100;
- number of acres - 10
If your plot has an irregular geometric shape, but you have correctly calculated its area in square meters, the method for calculating the size in acres remains the same. Plots with large area usually measured in hectares, each consisting of 10,000 square meters or 100 acres.
Calculation of land area online using a calculator
Today there are quite a few services and online calculators on the network that allow you to calculate the area of a land plot; just use one of the search engines, for example Yandex.
Keep in mind that online calculator When calculating the area, you will need the exact dimensions of all sides of the site in meters for its algorithm to cope with precise calculation the area of your plot of land.
An irregularly shaped area is more difficult to calculate, and the dimensions of the sides alone will not be enough to calculate the area of the area complex shape. Here you will need to know the dimensions of all sides of the garden, and the size of the diagonals. It’s a little easier if one of the corners of the plot is 90 degrees.
Here is an example of calculating acres of land summer cottage complex shape:
Dimensions of the sides of the land plot, in meters
- Side A-B = 69 meters,
- Side B-C = 46 meters,
- Side C-D = 87 meters,
- Side D-A = 35 meters,
- Lower left corner is straight (90 degrees)
Using these data, you can determine the lengths of diagonals B-D and A-C, and calculate the area of the plot = 3035 square meters (or 30.35 acres).
Sooner or later the owners suburban areas are thinking about fencing their territory and, accordingly, the need to draw up an estimate for construction. If you want to build a fence at your dacha with your own hands, then you should include in the estimate:
- Cost of materials. To keep your budget minimal and your fence optimal, pay attention to the components and clarify their characteristics. If you want to save money and take thinner, smaller, used metal (especially used corrugated sheets), with the wrong degree of protection, or available material, all this will ultimately affect the beauty and strength of the fence. If you bought unfinished pillars, joists, or gates with a wicket, their production will add to the cost of the final product. Of course, today you can buy everything in Leroy Marlin necessary materials for the fence. But metal and corrugated sheets Leroy Merlin Most likely it will be quite thin, although cheap. But self-tapping screws, fittings for gates with a wicket and other small things necessary for installation will be expensive. Additional factors influencing the cost of the fence include the presence of wickets and gates, double-sided covering of the sheet, canopy, forging and any other decorative elements, as well as a small supply of material. If we are talking about the need to fence the area with corrugated sheeting and invest in the minimum possible amount, also think about the need for roofing screws, decorative strips on top, mortise locks and some non-standard fittings for gates with a wicket. The fence does not tolerate any excesses to a minimum, so think about the need for concrete work.
- Cost of loading, delivery and unloading to the fence installation site. This is an important point that many people forget when they want to build a cheap fence with their own hands. You will rarely be able to save money here, and even vice versa, because you will most likely order all the components from different places. And if you order profile pipes from a metal warehouse, they are usually six meters long, so cutting them should also be included in the budget.
- Cost of work to prepare the site for installation. Nothing should interfere with the construction of the fence: old fencing, bushes, trees, tall grass, embankments, unnecessary things - along the installation line you must have workspace about a meter on each side. Of course, you can do this work yourself.
- Installation cost. It all depends on the complexity of the installation: the number of logs, the installation pitch of the pillars, the method of installation (in concrete or not), the number of gates and gates, whether all components of the fence are ready for installation, whether anything interferes with the installation (soil, buildings along the fence line, neighbors and other). Pay attention to your soil; if it is compacted clay, bulk earth mixed with stones or other heavy soil, then it is unlikely that you will be able to drill through with a regular gas drill and you will have to resort to additional expenses for plugging pipes. And then you won’t be able to put up a fence for your dacha with your own hands cheaply. Standard installation fences made of corrugated sheets, the price for work per 1 meter will cost from 300 rubles. But fencing companies rarely offer work without material, so installing a fence from corrugated sheets at shabashniks will cost from 70% of the cost of the material.
- Associated costs: electricity, gasoline, paint, electrodes, bits, cutting discs, screws and, most importantly, your nerves.
Let's calculate the approximate budget for a standard fence made of corrugated board for 6 acres. The configuration of the plots may be different, but most often 6 acres is 30 m by 20 m (600 sq.m.), the perimeter will be 100 linear meters. For example:
- a fence of 8 acres is approximately 20 m by 40 m - 120 linear meters. m;
- a fence of 10 acres is approximately 25 m by 40 m - 130 linear meters;
- fences of 15 acres are approximately 30 m by 50 m - 160 lm.
- SNT fences are most often more than 300 linear meters.
To install a fence inexpensively 100 meters long with a gate and a wicket without a foundation, 2 meters high, on 2 logs, we will need 38 posts (metal profile pipe 60x60 mm, wall thickness 2 mm, length 3 meters), 64 logs (metal profile pipe 40x20 mm, wall thickness 1.5 mm, length 3 meters), 87 sheets of C8 corrugated sheets (thickness 0.5 mm), standard gates with a wicket, add to this the costs of screws, bits, cutting discs, paint, electricity, electrodes, covers for poles material, delivery and installation.
Offer from the company "Fence at the House" for a fence made of corrugated sheets |
|||
|---|---|---|---|
| as of April 2019 | 130,000 rubles | ||
Do-it-yourself estimate for a fence made of corrugated sheets |
|||
| Name | Quantity | Price | Total cost |
| Pillars | 38 | 474 | 18012 |
| Lags | 64 | 189 | 12096 |
| Corrugated sheet | 87 | 700 | 60900 |
| Gate with wicket | 1 | 15000 | 15000 |
| Delivery | 2 | 6000 | 12000 |
| Installation | 70% of the material | 1 | 82605 |
| Other (screws + bits, paint, abrasives, electricity, electrodes, covers) | 1 | 10000 | 10000 |
| TOTAL for April 2019 | 210613 rubles | ||
Approximate cost of a standard corrugated fence for April 2019 on our own in the Moscow region will be about 210,000 rubles. If you use an online real price calculator, the cost of material and installation will be: 120,000 plus 3,000 rubles delivery.
- a 20-meter fence made of corrugated sheets with gates and a wicket will cost 32,000 rubles;
- fence 50 meters made of corrugated board without entrance group- 59,000 rubles, every subsequent 10 meters + 11,800 rubles.
Our company “Fence at the House” works at minimal prices due to well-coordinated processing of own production large supplies of rolled metal, a well-structured scheme of working with customers and a professional installation cycle on site. We can offer the most competitive price for all our products and therefore we install a lot of garden fences. Thus, if you order a standard fence made of corrugated board from our company, it will be profitable. But you can really save money on a measurer, a bar, roofing screws, double-sided covering of corrugated board. A significant help to the budget is to order a fence together with your neighbors, but you should take into account the fact that during a joint installation, disagreements may arise regarding the choice of material, color and height.
Currently on sale on the market are the main plots of 10, 12 or 15 acres, and the new section for cottage development starts from 15 acres, let's talk about this in more detail.
A plot of 15 acres is optimal solution, you can easily place a house, a bathhouse on it, outbuilding and green spaces.
How much is fifteen hundred? 1 hundred square meters is 100 sq.m., that is, a square of 10 by 10 meters.,
15 acres contains 1500 square meters, respectively; it can be a rectangle of any size, for example 50 by 30 meters.
Factors to consider when choosing a site
Important point is the same level groundwater. The higher the groundwater is located, the less it becomes bearing capacity soil. You also need to remember that you will need a source of water (a well or a borehole), hence this is an important indicatorWhen selecting a site, you must take into account whether it is upland or lowland. At all times, priority was given to areas on high ground. If the site is in a lowland, it will constantly be flooded after heavy rains and snowy winters, and even its artificial raising (filling) does not always correct the situation and is economically costly. This affects the cost of the site itself.
- You need to pay attention to whether the area is uprooted or not, since if uprooting of trees is required, this will require monetary costs, and sometimes not small ones.
- The depth of soil freezing is not such an important point that you should pay attention to when purchasing a plot, but you need to know it for your area, since the depth of the foundation, for example a strip foundation, depends on it.
- Visually assess the differences in heights in the area; if it is significant, leveling it will also require costs or an increase in the cost of the foundation, if it is the foundation that is used to level, for example, piles on screw piles.
- Before purchasing a plot, be sure to study the soil on it, as it is rocky, peaty, quicksand, less degree clay can create problems and increase the cost of the house as a whole by an order of magnitude. The choice of foundation directly depends on the type of soil; for example, soils closer to rocky soils completely exclude the installation of screw piles.
Don't forget about sanitary standards, operating on the development site 1 line of rivers and lakes.
- Give preference to areas with standard rectangular shapes, since in a narrow area it is difficult to plan everything correctly.
- An important point will be the possibility of connecting to electricity (the presence of a pole on the site or nearby) since electricity can be supplied to areas of new cutting for more than one year.
- The location of the site in the direction of the prevailing winds and cardinal directions is also an important point for many
The layout of the plot is 15 acres. Zoning.
What influences the layout?
Red line in urban planning, it is a conditional boundary separating the roadway of a street, driveway, highway, or square from the building area.The distance from the red line of the road is at least 5 m and at least 3 m from residential streets
When planning construction country house or a summer residence, it is necessary to define the following zones:
Residential area— the house itself is located in this area; it is possible to add a terrace and a garage. If the family has a car, then it makes sense to consider a house project with a garage.
Recreation area- most often it is located behind the house. There is a place for a barbecue, gazebos, playgrounds for children or a sports corner, and sometimes an artificial pond is installed.
Gardening area— in this zone there are beds, shrubs, flower beds, fruit and berry plantings. They immediately estimate the number of beds and plantings for the family’s needs. This zone can bring both harvest and play an important role, or just wear decorative function decorating the site itself.
Economic zone— this part of the site contains buildings for keeping pets, which include walks, enclosures and other structures.
It is not possible to comply with all the rules for the location of zones and objects on a plot of 6 acres; on 10 acres it is problematic, but on 15 acres you can realize all your ideas and ideas without problems.
Examples of planning a plot of 15 acres
1 option
Option 2
Important: SNiP 30-02-97
6.7.* The minimum distances to the border of the neighboring plot for sanitary conditions should be:
from a residential building (or house) - 3;
from construction for keeping small livestock and poultry - 4;
from other buildings - 1;
from the trunks of tall trees - 4, medium-sized ones - 2;
from the bush - 1 m
Choosing a home. Projects
When the site is planned, they begin to choose the design of the future house. The choice depends on the needs of the customer, it may not be large country house 6x6 for seasonal holidays or big house made of timber for permanent residence 10×10 or even 12×12 with or without a garageOption 1. This is a residential building with an attic, ideal for those who want an inexpensive house for a seasonal holiday in the country. The house has a terrace and a balcony for relaxation, which also decorates the facade of the house. The layout is both simple and thoughtful: the 1st floor has a large studio room divided into two rooms, the 2nd floor has a relaxation bedroom with access to a balcony of almost 18 sq.m.
Option 2., this house is made of profiled timber overall dimensions, including a terrace of 10.5×8, size without a terrace of 8×8 along the main walls. The house has excellent planning solution, including many rooms for various purposes. The plan of the 1st floor is a spacious living room, hall room, kitchen and bathroom, according to the plan there are 2 floors with a staircase with access to a spacious hall, from which three doors lead to three bedrooms. A open terrace on two sides of the house and a balcony make this project elegant. 
Option 3. In conclusion, we will consider several projects of houses with a garage. It is convenient and functional, and when there is no car, the room can be used as a utility room, for storing tools, for equipment sports section etc.
AND sectional doors, from the garage there is a separate entrance to the house
Installation craze beautiful fences in Russia is dictated not only fashion trend. With a competent approach to the process, fences can be installed on plots of 6, 8, 10, 12, 15 or 20 acres for a very reasonable amount.
What if quality product is available to most consumers, then its fate is determined - it will become popular.
The information in this article will help you understand the principles of calculations and production of fences for urban and summer cottages. Having understood how much fence you need for 8 acres or another standard area of land, you can choose and install the fence according to the most favorable price, saving, as they say, wisely.
How to calculate the length of a fence?
First, let us recall that one hundred square meters is a square of land with a side length of 10 meters. Thus:
- area of 1 hundred square meters - S = 10 x 10 = 100 m²;
- plot area of 10 acres - S = 100 x 10 = 1000 m².
To install a fence on 10 acres, you need to calculate the perimeter of the site. As we remember from the school curriculum, perimeter is the sum of the lengths of the sides of a figure. For example, for an allotment rectangular shape with sides of 20 and 50 meters, the perimeter will be calculated as follows:
- P = (20 + 50) x 2 = 140 meters.
Thus, a fence of 10 acres will have a length of 140 meters, provided that the site is completely covered. By analogy, the length of a fence of 6 acres can be calculated, as well as for other formats.
Technology for calculating materials for fences
There are also no big difficulties here and even, according to experts, you can do without drawings. It is enough to remember a few important nuances:
- main support pillars installed in each corner + along the edges of the gate and wicket openings;
- the number of auxiliary supports depends on the estimated width of the covering material;
- The height of the fence directly affects its cost.
As an example, let's try to find out how many meters of fence per 10 acres will be needed, provided that the profiled sheet marked C8 is chosen as the flooring, and the support posts are made of profile pipe 60x60 mm. Let's say we have a plot of 30 x 33 s total area 990 m² (almost 10 acres). We divide the length of each side of the site by the width of the profiled sheet (for example, 1.15 m) - we get 107 pieces.
If the supports are brick, the number of metal profiles will decrease due to the thickness of the pillars. We will consider the gate and wicket as a separate side using solid sheets metal coating. If the number turns out to be fractional, then we round it up so as not to get a hole in the fence.
We calculate the footage of the log based on the length of the profile and the design quantity (3 m each). Simple math also works here. We divide the total footage by 3, rounding up and multiply by the number of joists used in the fence (usually 2 or 3 rows).
In total, the calculation showed that for the simplest fence made of corrugated board and metal supports we need 107 sheets of corrugated steel, 246 meters thin pipe for making lags. The number of main and auxiliary supports, provided they are spaced every 2.5 meters, is 49.
Next, we place a table that gives the basic calculations for the manufacture of fences in the MASTEROVIT company. Here you can clearly determine how much a fence of 10 acres costs for a house within the city or a fence of 6.8 acres (a standard summer cottage).
Non-standard plot shapes
What to do if the landscape of your site is uneven or the area has the shape of an irregular polygon? The easiest way is to seek help from a specialist. Managers of our company will help you calculate for free the approximate cost of a fence for 12, 15, 20 acres (or any other area), while simultaneously giving advice on choosing materials taking into account the characteristics of the area.
The portfolio of the MASTEROVIT company contains photos of projects with an exclusive design created for a specific request.
Photo #1: Ready fence for a plot of 10 acres
Photo No. 2: Finished fence plot of 12 acres
The main factors in determining the final fence price
The cost of fencing is primarily affected by:
- costs of materials (concrete, brick, rolled metal, pipe, profile, accessories);
- fence dimensions (length and height);
- installation method (presence of a foundation or spot pouring, type of supports, cost of installation services).
It is important to determine in advance whether it will be necessary to pour a foundation for the fence or whether you can only dig in supports and reinforce them with concrete. The owner of a plot in a forested area, marked for the first time, will not be able to place strong house and a fence until it levels the landscape. All these aspects “come to the surface” during a geodetic survey, which is recommended to precede any construction on the ground.
It is difficult for an amateur to take into account such a number of nuances. That’s why it’s really worth contacting specialized companies to build a high-quality fence. Professionals will do everything correctly, using sophisticated technology, and will not conduct experiments on your site.
How to choose a quality fence manufacturer?
In addition to the well-known truth that preference should be given to experienced teams working in accordance with GOST standards, there is another simple secret. Once you have a rough estimate, estimate the cost levels for materials and services. If the work costs about the same as the materials or less, feel free to sign the contract - this is a good price.
In the life of each of us, various legal issues may arise, for example, we may enter into a contract for the sale and purchase of a land plot or a lease agreement.
First of all, any person will be interested in how many square meters are in one hundred square meters and how to calculate it correctly. Let's talk about this in more detail.
How to calculate - using a specific example
A weave is a square with a length and width of 10 meters, i.e. 10 meters * 10 meters = 100 m2 = 1 weave. In practice, this is approximately 12-14 human adult steps. Using the same analogy, you can calculate a hectare: 100 square meters = 0.01 hectares = 0.02471 acres.
Example: A plot of 9 acres - this means a plot of 30 by 30 meters, or 20 by 45 meters, or 25 by 36 meters.
Origin of the word "weave"
The word “weave” comes from the concept of one hundredth of something. In this case, this is one hundredth of one hectare; in the example, it would look like this: 0.01 hectares.
Now on our land the entire area is measured in hundreds. And not only the land is measured. The following example can be used: a tractor driver needs to process 30-35 acres per day.
Why are calculations needed?
Thanks to these calculations, you can find out the size of your house or garden. The cost of the plot in the transaction will depend on the amount of land. Knowing the size of the plot's land in acres, you can plan the development of other buildings on your land.
Abroad, it is customary to measure land using other measures. Before the introduction of the metric system in Rus', ancient Russian measurements were used. Previously, land was measured in tithes, and a hectare included twelve such tithes.
Yes, and on our land they began to measure land in hectares and acres not so long ago. This happened from the beginning of the October Revolution and the formation of the Soviet Socialist Republic.
But even in our time, not all countries measure land in hundreds. And in the territories that were under power Ottoman Empire the land is measured by Dunam. In Thailand, the measure of earth is called paradise.
The conclusion can be drawn as follows: one hundred square meters is one hundred square meters. The concept of “weave” is quite convenient; it arose about 100 years ago and its main property is the measurement of land.
The value is quite convenient and simple, does not require complex calculations. This calculation can be performed by anyone. It is enough to take a certain number of steps and you will see the allocated area.
