When the walls and roof with roofing are ready, it is necessary to think about finishing the overhangs of the roof frame. Some owners leave it without additional filing, however, uncovered places not only spoil the appearance of the building, but are also subject to the destructive influence of environmental factors. Roof filing with siding is one of the options for an inexpensive and beautiful coating, which is used for buildings made of various materials.
Material selection
Before you buy roof siding in a hardware store or arrange delivery from Internet resources, you need to figure out what materials it is made of and which one is better to choose:
Walls and roofs are sheathed with metal. In stores, you can find galvanized siding that looks like round logs in shape and with a wooden texture on the surface. Metal is not afraid of mechanical influences and direct sunlight. An additional coating protects it from the damaging effects of moisture. However, at the joints, scratches and chips, the metal can quickly rust and spoil the appearance of the skin.
Roof siding is a solid sheet of aluminum covered with a decorative layer. Due to the additional surface coating, aluminum is more resistant to environmental factors.
Made from PVC. This material is lightweight, not afraid of prolonged exposure to moisture and sunlight. In addition, PVC is inexpensive and has a high rate of durability.
It is considered the best material for filing the overhangs of the roof frame. This is due to high rates of resistance to environmental factors, ease of installation, low price. Perforated parts allow air to pass under the material and prevent mold from forming on the wooden roof frame.
On our website you can find the most . In the filters, you can set the desired direction, the presence of gas, water, electricity and other communications.
Previously, wooden lining was considered the most popular material for filing overhangs. However, the beautiful appearance could not outshine the disadvantage associated with moisture. With prolonged exposure, it quickly destroyed the wood and brought the filing into disrepair.
On a note! In addition to siding, you need to purchase fasteners. Self-tapping screws should be smaller in width than the holes located at the joints of the decorative coating sheets.
Wireframe creation
The amount of material will depend on what type of frame the home owner has chosen. There are two options for building a frame. It is necessary to make a choice before sheathing the roof overhangs with siding:
horizontal box(perpendicular to the rafter system). The most popular option for filing overhangs. Suitable for pitched roofs. To make it, you need two boards and two bars. Boards should be fixed at the end of the rafters and on the wall. The bars are located between the boards so that they can be fixed to the siding panels using self-tapping screws.
Box in the direction of the rafters. This option is used on shed roofs, with a slight slope of the slope. On the inner sides of the rafters, the bars are stuffed at the same level. Siding panels are fixed on top of them.
Before starting further work, it is necessary to check the frame using the building level. The difference between the arrangement of parallel bars and boards will ruin the appearance of the hemmed areas.
Rules for working with siding
There are a number of rules that must be followed in order not to encounter problems during installation and further operation of the overhang cover:
Before starting to attach the sadding panels, there must be installed profile around the perimeter.
When using plastic siding, the panels are cut 5 mm less required size. Thus, there is free space in case the material expands when heated.
Required maintain air exchange. To do this, you can alternate ordinary panels with perforated ones. The optimal interval is 1 m.
self-tapping screws can't turn all the way. It is required to leave 1 mm of free space for the movement of material during expansion.
Before finishing, the legs of the rafters must be cut in one level. To check whether the cuts were made evenly, you need to pull the thread between the first and last paws of the rafters.
On the end side of the roof, rafters closed with wind flaps. They prevent moisture from entering the space between the siding fixed on the gable overhangs and the roof.
wind slats Source: montazh-saidinga.ru
By following these rules, you can avoid most problems later on.
Carrying out the main work
The process of finishing the roof eaves with siding will depend on the chosen frame and the direction of the decorative coating panels.
The location of the siding under the roof (along the rafters):
The first step after the manufacture of the frame should be mounting J-profiles. They are fixed on parallel elements of the frame (opposite each other).
Second phase - location of the start and finish bars. They need to be level. The integrity of the coating and appearance will depend on this.
After installing the guides, it goes siding panel installation. Initially, they are measured in size, cut with a grinder, or special scissors. The first sheet starts behind the J-profile. Then it is fixed on the starting bar with self-tapping screws. They must be screwed into the mounting holes.
When all panels are installed and securely screwed to the frame, it is required close outside areas with decorative corners.
Multidirectional joints between the panels are closed with decorative strips.
The location of the eaves siding horizontally:
Selected material measured and cut by size.
Initially Required fix the first bar profile according to the level at the bottom or top of the overhang. From the installed profile, all other panels begin to be fixed.
According to this system, the siding is fixed to the gable overhangs.
You also need to talk separately about how to properly install siding on a horizontal ledge near gable roofs:
Initially should be finish plate installed. It is depicted in the figure under the number 1.
To carry out any work on sheathing overhangs with siding, you will need three types of profiles - J-profile, starting and finishing strips.
It is advisable for the owner of the house to take into account the advice and recommendations of people who have already done filing overhangs with siding. These recommendations will answer many controversial questions and help in the process of work:
The distance between fasteners (screws, nails) along the length of the profile must not exceed 35 cm. More fasteners will lead to extra costs, and less can cause sagging.
From the moment of purchase to the start of installation work, siding must be store under light-tight polyethylene film outdoors. Bars or boards are placed under the bottom sheets so that the material does not come into contact with the ground.
Important handle locks carefully located on profiles and panels. With too much pressure, they can break.
To cut profiles and plates evenly used grinder. Simple pruning is done with scissors for metal.
To create good ventilation, special ventilation grates. They will provide air circulation between the siding, insulation (if any) and roofing.
Before installing siding roof needs to be insulated.
Many builders coat panel joints using a sealant. You don't need to do this.
If the panels are contaminated with dust or dirt, they can be cleaned with a damp cloth with the addition of a singing solution. Do not clean panel joints with metal brushes and powerful chemicals.
Video description
In the video you can see the filing of the roof with siding:
Conclusion
Roof filing with siding is a way to protect the rafters and frame from environmental factors, as well as improve the appearance. It is important to choose the right material, and carry out installation according to all requirements.
The modern construction market is filled with a variety of materials with high performance characteristics. Among this variety, it should be noted the options that are used both for facade cladding and for sheathing cornices, including roof siding, with its inherent unique properties.
Siding is a vinyl panel that has a variety of colors. The complete set of this facing material is represented by various planks, cornices and profiles, which makes it possible to give the building a special appeal and protect it from the negative effects of various natural phenomena.
In order to independently sheathe the eaves with siding, you need to know the main differences between this material and have an idea about the process itself.
Siding for sheathing eaves
Vinyl siding is most commonly used for sheathing, but wood, galvanized, and galvanized metal eave siding can also be used. The vinyl version is lighter, stronger, more reliable and inexpensive. Standard panels have a length of 3 to 3.6 meters, each of them has profiled strips measuring 10-12 cm and special locks on the edges.
The cornice is sheathed with spotlights of two types:
- Solid siding panels without perforation.
- Soffits with partial perforation.
The use of the second type contributes to the creation of more proper ventilation of the space under the eaves.
Vinyl spotlights
When hemming the cornice with vinyl spotlights, it is important to adhere to the following rules:
- Before direct use, the material is stored in places with limited access to sunlight at a temperature not exceeding +60 degrees.
- Installed panels must move freely horizontally.
- When fixing the panels, do not apply force to prevent damage to them.
- Fixing spotlights is best with self-tapping screws.
- Fasteners are not screwed in until the cap is completely drowned, it is recommended to leave a gap of at least 1 mm. Too much pressure can cause the panel to break.
- It is not recommended to use sealant between soffits and corner elements, as well as between panels and profile.
Installation of a box for overhangs
Before the direct sheathing of the eaves, the box is mounted. For its manufacture, wooden blocks or an aluminum profile are used. The first option is suitable for clapboard lining, in other cases the box is made of aluminum profiles.
For the box, you need to take two boards, one of which is mounted on the wall, placing the lower part strictly horizontally. This is necessary for the smooth installation of the eaves siding strip.
Hemming the eaves with spotlights is not considered a difficult process, but requires a responsible approach. In addition to the decorative purpose, the panels also have a functional load, since the hemmed cornices give the building the appearance of a completed construction and at the same time protect the house from moisture and rain.
Among the advantages, it is worth noting easy installation and the possibility of implementing various architectural ideas thanks to various types of siding and accessories.
In order to qualitatively solve the problem of how to sheathe a cornice with a soffit, it is enough to perform the following steps:
- On the cornice overhang, two special strips are mounted.
- Profiles of a special shape are attached to the board on the wall.
- Soffits are cut into segments of the desired length and aligned in accordance with the width of the overhang.
- With one edge, the panel is inserted into the groove, and the other side is fixed on the installed bar.
- A decorative bar is installed along the line connecting the spotlights with the exterior cladding of the house, which makes the overall look more attractive.
Mounting Features
It is possible to hem the roof with siding only after installing the truss system. This will help to correctly solve the problem of how to sheathe the cornice of the house with siding.
The process of filing itself is characterized by several features:
- For high-quality sheathing of the eaves, it is required to make vertical cuts of the lower heels of the rafter legs. At the same time, it is important to control that the cuts are parallel to the walls of the house.
- Sheathing is best done with special strips that match the color of the roof or the exterior cladding of the house. The use of ordinary wooden boards for this purpose will not add aesthetics to the structure.
- The lower heels of the rafter legs are sawn off vertically, as they must be sewn together with the entire structure.
- It is recommended to insulate the walls before sheathing the roof overhang with siding.
Sheathing of roof overhangs with siding is done in two ways:
- In the first case, a horizontal box is made of boards, attaching one of them to the wall and the other to the bottom of the rafters. In the place where the roof slopes converge, they put the board with a wide part, making even joints. In this case, it becomes possible to create a structure independent of the walls of the house. The fastening of the slats is carried out using corners and plates.
- The second option is used for shed roofs, the cornices are hemmed along the line of the rafters. In this case, when arranging the frame, it is important to take into account that the angle of inclination of the filing must match the slope of the slope. The rafters in the lower part should be as even as possible, so that screwing the board did not cause difficulties. Using this method for a pitched roof requires the mandatory installation of two boards on opposite sides at the junction of the slopes.
The process of sheathing the eaves - how to sheathe correctly
The problem of how to sheathe siding under the roof is solved using the following materials:
- Siding, the color and profile of which are chosen in accordance with the type of roofing or facade cladding material.
- Profiles of various types, external and internal corners.
- Self-tapping screws. These fasteners do not allow the panels to fit snugly to the crate or to the corner profiles.
A frieze strip may also be needed if the installation work involves its use. This element is installed directly above the cornice profile.
Direct installation is not a difficult process, the main thing is that the rafters are properly prepared for the installation of the box. The parts of the rafter legs protruding beyond the line of the facade must be strictly parallel and even.
The direct sheathing of the eaves begins after the work on the thermal insulation of the walls of the house. For free air circulation, special grilles are made. The implementation of these actions contributes to the high-quality sheathing of the eaves with siding.
Features of copper spotlights
Due to the high cost, copper siding is used very rarely, although its quality characteristics are at a high level. Over time, copper becomes covered with an oxide film, due to which it acquires a reddish tint and a beautiful appearance.
Copper soffits are thin sheets characterized by high thermal conductivity and high resistance to corrosion. Hemming the cornices with such material, you can solve a large number of problems, including resistance to aggressive environmental influences and moisture. The use of perforated soffits allows you to create conditions for free air circulation.
Connoisseurs of beauty use patinated coatings for sheathing cornices, which are characterized by the presence of a noble malachite-green hue.
Two types are often used:
- siding without perforation.
Why choose spotlights
- hooks for gutters;
- metal scissors;
- gutter;
- electric saw;
- special profiles;
- punch;
- eaves siding;
- cornice boards;
- end and start bars.
Roof sheathing with siding requires a box. You can make it from or wooden bars. Only wooden blocks are suitable for lining, in other cases aluminum is suitable.
Siding installation rules
Important points of work
- For the eaves, it is recommended to use strips under or roofs, ordinary boards are also used, but they do not give such an effect.
The choice of siding for sheathing
For the roof, not only vinyl siding is used, but also wooden, metal, galvanized materials. The vinyl version is used more often because of its strength, lightness, reliability and low cost. Panels made of siding are thin sheets 3 m long. Each panel has several profiled 10 or 12 cm planks equipped with locks.
Roof siding may vary. Two types of soffits are often used:
- soffit with partial perforation;
- siding without perforation.
Why choose spotlights
They are made from vinyl or metal. The following advantages of such a product can be noted:
- Soffits are made both in perforated and solid form.
- The perforation of the material for the pediment can be solid or running along the central part of the part.
- The perforated panels are sheathed with an enlarged cornice, and with solid panels - the cornice of the pediment.
- Soffits have an attractive appearance, they are easy to process and cut.
- The weight of the vinyl product for overhangs is small, the material is simply mounted, it is durable, it is not subject to corrosion.
- Aluminum spotlights for overhangs are made of a single sheet with a decorative layer.
What is required for cladding
Roof filing involves the use of various tools and materials. You will need the following components of the workflow:
- hooks for gutters;
- metal scissors;
- gutter;
- electric saw;
- special profiles;
- punch;
- eaves siding;
- cornice boards;
- end and start bars.
Making a box for overhangs
Roof sheathing with siding requires a box. You can make it from an aluminum profile or wooden bars. Only wooden blocks are suitable for lining, in other cases aluminum is suitable.
Installation of eaves with siding (video)
The box for filing the gable cornice is made of two boards, one of which is attached to the wall. Soffits are not easy to install, but if you approach the work responsibly, everything will work out. Overhang panels not only perform a functional load, but also protect the roof from excess water during rain or snow melt.
Soffits for the roof will allow you to embody any architectural solutions. Thanks to a wide range of accessories and types, finding the right option will be easy.
Spotlights for overhangs are mounted in several stages:
- Two planks are installed on the roof eaves.
- J- and F-profiles are fixed to the bar located near the wall.
- Soffits are aligned to the width of the overhang.
- One part of the panel is inserted into the groove, and the other is fixed on the mounted bar.
- The joints of the spotlights and roof siding are covered with a plank.
How to competently carry out cladding
You can sheathe the gable with only three types of profiles - the start bar, the finish bar and the J-T rim. You can decorate the corners with anything you like, but the installation of panels should be carried out only on the presented profiles.
The installation of the J-T rim roofing strip is for the end parts of the panel, if the siding is finished across the frame. The starting bar is attached directly to the side where the skin will come from, and the finish bar will serve as the end. The presented profiles require rigid fastening with self-tapping screws or nails with a step of less than 40 cm.
Roof filing involves compliance with other rules:
- The material should be stored in places sheltered from ultraviolet light, and the ambient temperature should be less than 60°C.
- The cornice sheathing should allow some freedom of movement of the panels in the horizontal direction.
- Do not drive too much fasteners into the siding, the material may collapse.
- Sealant must not be applied between panels, corners and profile.
- When installing siding, do not put much pressure on the locks.
Siding installation rules
Sheathing of the pediment is carried out after fixing the profiles around the perimeter. The panel is cut to 5 mm less than the net length in order to provide room for expansion when heated. Self-tapping screws are placed in the center of the holes.
When filing the roof, it is important that the head of the self-tapping screw does not fit closely to the vinyl, it is necessary to leave a distance of 1.5 mm. Every meter there should be a panel of perforated siding.
When finishing the pediment, one should not forget about the need to maintain air exchange. To accomplish this goal, you can alternate regular and perforated panels with an interval of 1 m. If such siding is not available in the store, you can drill holes in standard panels.
You can hem the cornice when turning 90 ° with a direct docking or with a mustache. For docking, a J-T rim metal profile is used. Its cost is not high. You can cut the material with a grinder or a hacksaw for metal.
The hemming of the pediment along the cornice with a width of the latter less than 360 mm can go to the transverse frame. Siding in this case is installed along, while it is better to take a wider soffit. In this case, a wooden crate can be made using corners made of timber, located at a distance of 0.5 m.
Important points of work
You can hem the roof only after installing the rafters. In this case, there are features of the installation that must be taken into account:
- Before finishing the roof, the ends of the rafters are sawn off at one level.
- For the eaves, it is recommended to use strips to match the color of the facade or roof, ordinary boards are also used, but they do not give such an effect.
- Saw off the rafters for the roof vertically, their upper part is sewn up with filing.
- Wall insulation is carried out before finishing the overhang.
Mounting the soffit on the hemming (video)
You can do the roof lining yourself, if you make some effort. PVC products for the pediment do not wear out, are heat resistant and do not lose color. The presented qualities provide the material with long-term operation. Unlike lining, spotlights do not rot and do not lose their attractive appearance, but their installation requires a number of tools. Before starting work, it is worth preparing a box of aluminum profiles and wooden bars, only panels can be fixed on it.
Of course, it is best when the walls are sheathed with the same material, creating a single holistic picture.
Covering a canopy in a private houseSiding on the ledge
When you hem them with something, either a cornice board or a panel, always remember that in no case should the air circulation under the roofing material be disturbed. The diagram above shows the ventilation cycle, and if it is interrupted, it will result in the formation of mold.
rack frame
Transverse cladding method - It is much more expedient to use vinyl panels for them than steel ones, because when installing short pieces, it has to be bent, which is not permissible to do with metal - this is fraught with deformation. Therefore, we will pay attention to how the frame is made for the transverse cladding method.
- Considering that paneling is done from the ground and such work cannot be done from growth, you should take care of having a ladder or scaffolding.
It is best to use scaffolding and for this you need to knock down a couple of goats, on which boards are subsequently placed, and you can move freely along them.
In the private sector, the question: "What then to do with the goats?", at least, is inappropriate, because they will always find a use.
Scheme of the frame skeleton for filing the surface - If you decide to hem the house with your own hands, then you need to figure out how to make a frame or crate for cladding, in this case plates.
This design can be assembled from well-dried boards or bars, and the minimum thickness of the latter should be 25 × 50 mm (the board should also be used no thinner than 25 mm).
Advice. If filing is done simultaneously with the insulation of the facade, then first of all you need to process the wall.
In the case of the reverse order, part of the wall will remain uninsulated, which will significantly reduce the effect of the thermal insulation of the house.
- You should understand that finishing the canopy is, first of all, facing the lower, open part of the triangle and you will have to equip the base for the panels in this area.
Pay attention to the schematic diagram of the frame above and you will see that a right angle is assembled from the side of the beam, which is inserted into the hole between the roof slope and the wall.
Such devices must be installed along the entire length of the wall in order to attach slats or boards to them. - In order for the corners of the timber to be set evenly, you need to beat off the control line on the wall of the house with a choline.
To do this, using a water or laser level, set the marks at the required height and, by attaching a masking cord to them, make a landmark.
Arrangement of the crate - The distance between the corners to which the rails will be attached should not be more than 50-60 cm so that the structure remains rigid in any weather.
Now nail or screw the slats for the crate with screws, constantly checking their level, as can be seen in the photo.
If the crate for siding will consist of several levels, then you will have a multi-level frame, then you need to install it all right away and only then start facing.
Facing
Profile strips for fastening - Of the variety of profiles that are presented to you, sheathing will require only three types of all - these are J-trim, start and finish strips.
If you wish, you can decorate the corners with anything, but you need to mount the panels on the above profiles, as required by the instructions.
- J-rim strip is installed for the end parts of the panel, as we will be finishing across the frame.
You will fix the starting bar on the side where the finishing will begin, and at the end, of course, strengthen the finish strip (you can, of course, get by with one J-trim profile in this case).
These profiles must be fixed rigidly, with nails or self-tapping screws, in increments of no more than 40 cm.
Coating installation - After you have fixed the profiles around the perimeter, you can proceed to the installation.
The panel is cut 5 mm less than the net length - this distance is necessary so that the PVC can expand freely when heated.
- The panels can be fastened to nails or self-tapping screws, but in any case, this fastener should fall in the middle of the mounting hole of the perforated part of the material.
As we said, PVC contracts and expands with temperature fluctuations, so it will move, and the displacement stopper can cause deformation of the cladding.
Another very important point is that the head of the nail or self-tapping screw should not fit snugly against the vinyl, but remain at a distance of 1-1.5 mm (do not finish off the nail slightly, and do not tighten the screw 2-3 turns).
Install a panel of perforated material every meter - From the very beginning, talking about how to sheathe the cornice, we mentioned the need for ventilation, or rather, even about maintaining the air exchange cycle.
For this, there are special perforated panels that you will have to alternate with ordinary ones every meter.
If you cannot purchase this option in a store, then just drill holes in a regular panel.
- And how to hem the canopy when turning 90⁰, that is, on its other side? There are two options for this - "on the mustache" and the usual, direct docking.
In the opinion of the author of this article, the first option is more aesthetic, although such a statement is not a dogma. It all depends on how you arrange the profile strips. - In any case, J-trim metal profile for siding is used for docking, the price of which is in the middle between the starting corner bar.
You can cut such guides with a hacksaw for metal, or with a grinder with a cutting disc for steel.
Advice. You can cut PVC siding panels with at least three tools - a hacksaw, scissors and an angle grinder (grinder) with a cutting disc.
Roof lining with soffit along - If the cornice has a width of 360 mm or less, you can significantly speed up the filing by making a transverse frame. It is necessary to mount on such a device along, but not a regular panel, but a soffit, since it is wider and completely covers the distance.
For a wooden crate, in this case, there will be enough corners from a bar (we have already used such for a longitudinal frame), installed after 50 cm.
Conclusion
In words, of course, everything is very simple, but with effort and maximum concentration, you yourself will be able to perfectly perform such work, especially since you also have information on the video clip. Polyvinyl chloride siding almost does not wear out, it does not lose color and is heat-resistant - these qualities provide the material with an almost unlimited service life.
Finishing the eaves with siding with your own hands - step by step instructions. Finishing a house with material such as siding is a great solution for every building, whether it's a workshop or. Not only walls can be decorated with such a finish. Even the cornice ledges began to be trimmed with siding. Let's look at how to finish the cornice with your own hands.
Wooden
This type of siding looks very expensive and aesthetically pleasing, it will not be difficult to install it and no additional products will be required. But keep in mind that cornices tend to collect condensate, for this reason, wood products will constantly be damaged by moisture. If the cornice is on the street, there is a place for temperature effects. These two factors inevitably lead to the resolution of the material.
Metal
Since it is not very profitable and convenient to hem a cornice with wood siding, let's try to consider another option. The metal is strong enough and inspires confidence, but because of the same condensate, it will begin to rust even though it has a galvanized layer. As a result, rust spots with a characteristic reddish color are visible. Aesthetics will be lost, and strength will disappear with it. Of course, if the option of buying a copper profile, as it is resistant to corrosion and has a beautiful noble shade. Just think about the cost before you hem a cornice of this type. The price of copper material is high.
Vinyl
Both of the previous options are not very suitable, and also quite expensive. Vinyl siding is relatively inexpensive and more common in construction due to its resistance to moisture.
The PVC from which this type of siding is made has:
Keep in mind that siding is not suitable for finishing the cornice by itself, so soffits are used - special products designed just for the cornice.
These are panels with or without PVC perforation, which are needed to protect the cornice from excess moisture.
There are several types of soffits that differ in the type of perforation:
- Without perforation.
- Partially perforated.
- Fully perforated.
This is necessary for ventilation of the cornice space. In order for the cornice siding trim, the photo of which is attached in the article, to be correctly selected, first you need to familiarize yourself with the project. Based on the engineering solution of the cornice assembly, determine the degree of possible moisture. It is also possible, thanks to the study of the project, to immediately select the desired shade of the product, with which you will produce the finish.
The most popular spotlights are those that have a combined perforation. They will give you the opportunity to get excellent ventilation, while moisture will not get inside. The topic of ventilation in wooden houses is especially relevant. From an excess of condensate, the wood begins to rot, and this affects the bearing capacity. A metal frame will also not be complained about by moisture. Rust not only "eats" the usable area of the elements, but also spoils the appearance.
In a warm attic room, it would be more expedient to hem the overhangs with solid spotlights. They are needed to prevent cold air from getting inside and protect the roof from moisture that can get in from the outside. Fully perforated panels for enhanced ventilation. In this case, the panel will contribute to the movement of air masses. This type of panels is used for roofing with non-ventilated continuous decking. For example, if you have a roof made of shingles or covered with rolled materials.
Mounting points
In order for the filing of the cornice to be correct and have the desired aesthetic effect, certain subtleties should be known.
Types of interface of load-bearing elements
By tightening
Soffit installation
Tools and fixtures. You will need:
- A hammer.
- Building level.
- or a special knife for cutting siding.
Mounting
The simpler an action seems to be from the very beginning, the more difficult it is to perform. Proper finishing of cornices with do-it-yourself siding requires consistency and thoughtfulness, as well as watching a lot of videos, photos and studying information on the topic.
Process
Features of working with the material
Each material has its own distinctive features. The siding is very easy to install, but don't go overboard with the mechanical type. If you press hard or snap the joints together, you can easily damage the panel. Open fire and exposure to the siding will begin to melt, so do not bring burners or any other source of fire near it. PVC panels do not burn, so there should not be a fire.
If you plan to attach hooks or hangers of the desired shade to the cornice, consider this in advance. It is important that you do not attach them to the siding, as it will not support the weight of the flower, pot, and earth. But where fastening is permissible is to the rafter leg or crate for spotlights. Finishing the eaves with siding is very common due to the lightness of the material. You can mount the panel yourself. Difficulties will be only with the length, since it is quite difficult to keep 3.5 meters in weight.
A huge advantage is that the installation is simple - no expensive equipment or power-hungry tools are required. There are also no special technologies and ornate schemes. Everything is quite simple and is done with the help of those tools that are at hand.
Conclusion
Based on everything that has been said above, it becomes clear that the work can be easily done on your own. There is nothing difficult if you choose the right materials and learn about the installation technology. Therefore, arm yourself with all the information from the article and you can safely start the battle for your comfort and beauty at home. And remember that everything is in your hands!
