Scher-Khan Magicar V - user manual. Scher-Khan car alarm programming

Excellent operational characteristics and the "Sherkhan Magikar 5" alarm system has high reliability. The instruction manual gives a detailed explanation about the principles of using this device and its main functions.

purpose

The instruction "Sherkhan Magikar 5" indicates that this alarm can be controlled by the user remotely, which is helped by an exclusive keychain communicator. The display is made of liquid crystal material, so it is considered particularly reliable.

A specially built-in system regulates a single interaction mechanism processor unit with keychain communicator. You can control the alarm from a distance of 1500 m.

The engine starts after a special command is given. It is usually sent along the key fob, the outer part of the device, the internal timer. This does not take into account the temperature in the car, and the voltage level of the battery is also unimportant.

Advantages

Preparing the key fob for work

Before using the key fob, you need to perform several manipulations, since there is no battery in it during transportation. It is located separately, and not in the proper compartment. This is necessary to conserve battery power. in full. When you remove the battery, no power is consumed, so there is no need to additionally recharge the device.

To place the battery in the right place, carefully remove the latch that holds the Sherkhan Magikar 5 battery cover in its original position. In this case, malfunctions are excluded, since all structural elements are made with maximum quality. This applies to both cutting parts and the material from which they are created.

After performing this action, it is necessary to move the cover itself to the side that runs opposite to the protruding antenna. The battery for power should be carefully installed in the compartment. As with any battery, polarity is provided here, so the position of its sides can only be determined after familiarizing yourself with the graphic pattern near this compartment.

If any indicators are missing, then the Sherkhan Magikar 5 signaling is placed with a minus sign in the direction where the antenna is located. After correct installation a characteristic melody is heard, which indicates the completion necessary action for the correct operation of the system. You only need to close the battery storage compartment cover, and then install the appropriate lock on it.

Arming

To activate the security mode, you must first turn off the ignition, and close all compartments of the car to ensure the free operation of "Sherkhan Magikar 5". The operating manual determines that the button number 1 on the key fob is then pressed with only one touch. It is not necessary to hold it for a long time, a point and moderate touch is enough. The system will automatically translate everything necessary elements machine in guard mode. The existing locks on the doors will be blocked, the starter will not work until the owner himself removes this mode.

When the car alarm "Sherkhan Magikar 5" is armed successfully, a person can trace some signals:

1. The siren will sound once with a moderate whistle.
2. The emergency light signal will also make itself felt once.
3. An LED indicator will turn on, which will show that the car is under protection by means of measured flashing at a frequency of 1 time per second.
4. The headlights flash five times simultaneously. Further, the image of the closed lock will remain lit until the car is unlocked, and the headlights will go out.
5. The key fob will give only one short signal.

Enable sensors

When the LED begins to flash steadily, this means the activation of the system control over the state of all possible inputs and methods of penetration into the car, which the Sherkhan Magikar 5 cannot allow. The instruction manual reports that even the sensors for calling the owner and ignition control are additionally checked and constantly monitored, which allows the owner to calmly do any of his business at this time.

If connected additional function, which is responsible for regulating the delay of the cabin light, will also provide for the control of triggers, which usually do not begin to be guarded immediately, but only after a certain amount of time has passed. activates work 30 seconds after the machine has been armed.

A warning

The instruction "Sherkhan Magikar 5" warns users against inattention to the car. Shouldn't be left open doors, hood and luggage compartment. If this happens, then the person suddenly, instead of the usual behavior of the car when arming, hears a three-time key fob signal along with a siren. In this case alarm also flashes three times at once.

On the display, you can see the image of the item that the owner of the car forgot to close. This happens only for five seconds, so the user may not have time to see the desired item. At the same time, the text FALL appears on the display. This is a direct indication that you should find an unclosed element and cover it tightly.

"Sherkhan Magikar 5" instruction manual defines as a device upper class, since it sets all vehicle communications on guard, but it bypasses the activated sensor. It will automatically be additionally protected after the owner closes it. The hood area is not reflected in common panel, as it refers to the trunk area.

Automatic transition to armed mode

Passive arming is a separate feature that can be enabled or disabled for Sherkhan Magikar 5. The autorun instruction provides - you just need to change the state of the selected function. If the owner decides to activate just such a mode, then immediately after the last door is closed, the timer is activated, and the security is turned on after 30 seconds.

When the countdown is started, the system constantly sends warnings that this mode will turn on. This happens every 10 seconds. If any door is opened at the specified time, the system will activate the armed mode at the countdown of 30 seconds after the last door is closed. You can see if this function is working by the word PASSIVE, which is always shown on the display in this case.

Alarm mode

When Sherkhan Magikar 5 is operating, malfunctions are unacceptable. When any door is opened, the system will automatically be in alarm mode for exactly 30 seconds. When this time is over, it will return to the standard state again.

If the cause that caused the alarm has not been eliminated by this time, the signal will sound every 30 seconds and last for half a minute. This cycle is repeated eight times. If even then the reason for the violation of the usual mode is not canceled, the system returns to the armed mode, but on condition that the active sensor is bypassed.

Features of work

If the shock sensor is triggered, that is, there is a strong impact on any part of the car, the Sherkhan Magikar 5 alarm will be in alarm mode for 5 seconds, during which a strong signal from the siren and alarm is given.

With a weak impact, that is, the activation of the warning zone, also regulated by the shock sensor, 4 short ones will sound, which are generated by the Sherkhan Magikar 5 car alarm. There were no malfunctions in this process, so the owner of the device can be confident in his own technique.

Many users appreciate the ease of use of Sherkhan Magikar 5. How to disable security mode? With a short one-time press on the key fob button number 2. If you correctly program all the functions of the device, the alarm will become a reliable assistant in ensuring the safety of the car.

Example notation:

I - quick (0.5 sec.) button press

I - long (2 sec.) button press

(I + II) - fast (0.5 sec.) simultaneous pressing of the buttons (combination of buttons)

(I + II) - long (2 sec.) simultaneous pressing of the buttons (combination of buttons)

Note:

With a long 2 sec. pressing the I button, the car alarm operation modes are sequentially changed in the order (1) > (2) > (3) > (1) .... In mode (2) the "Hands-free" function has a long working range - the symbol flashes.

Setting the time on the keyfob-communicator display

Setting the current time is required before starting the operation of the system or when changing the key fob battery. Follow the steps according to the table below.

ATTENTION!

Setting the correct time is necessary condition for correct operation automatic start of the engine by timer.

Setting the key fob-communicator modes.

Vibration call, owner call, temperature display standard "°F" or "°C"

To set the desired operation mode of the car alarm key fob, follow the steps in accordance with the table below.

Scher Khan security systems have a long range of two-way communication. Autorun Sherkhan 5 can be performed according to several settings, depending on the desire of the owner.

[ Hide ]

Main characteristics

Deactivation of the signaling from the key fob

The operation of the system is possible in a passive mode, when the activation of the protection occurs half a minute after closing all the doors and covers on the body. If the doors do not open when the system is turned off, it will automatically arm. To use the passive mode, it should be activated by briefly pressing the second and third buttons of the main key fob.

Passive operation mode is active (the Passive icon is lit on the display)

If the doors and the trunk lid were opened and closed, the system will turn on protection half a minute after the lock of the last element is clicked into place.

Keychain - communicator

The main key fob supplied in the kit has the following functional features:

• thanks to the four-button scheme, it is possible to control all system functions;
• the signal from the key fob is encoded according to a special Magic Code scheme, which prevents interception and recording;
• the built-in display with illumination provides visual display of all operations;
• when working with the system, the key fob confirms commands with a sound or vibration signal;
• additional information from sensors can be displayed on the screen;
• the key fob is the main tool for programming automatic start;
• using the key fob, the system parameters are configured.

After unpacking and installing the system on the car, it is necessary to bring the main key fob into working condition. To do this, you will need to remove the dielectric gasket installed between the contact pads of the battery and the key fob power circuit.

Action algorithm:

1. Open the battery cover. To do this, open the latch and slide the cover to the bottom of the key fob.
2. Remove the battery from the compartment.
3. Remove the gasket located along the entire length of the element.
4. Return the battery to the local location, observing the installation polarity indicated on the sticker. If there is no marking, remember that the negative pole of the battery is always directed towards the antenna of the Sherkhan Magikar key fob.
5. Close the lid and lock the latch.

Pictograms on the keychain Sherkhan Magikar 5

The following symbols and icons may appear on the screen:

• timer start (A);
• turbo timer mode (B);
• passive activation of the system (C);
• automatic activation mode without pressing the buttons (D);
• included siren (E);
• shock detection sensor (F) is off;
• vibrating alert is active in the key fob (G);
• control of door locks after starting the ignition (H);
• open trunk lid (J);
• the engine is switched on in the autostart mode (K);
• system state (L);
• open doors (M);
• field for displaying hours, temperature and data during autorun (N);
• operating mode Valet (O);
• working alarm or dimensions not switched off (P);
• shock sensor triggering (Q);
• key fob battery indicator (R);
• signal level (S).

Marat Askarov demonstrates setting the clock in the Magicar 5 key fob.

Autostart security system

Under the autostart of the system, they mean turning on and off the protection without pressing the buttons on the key fob. The mode is named free hands” and is activated by pressing button one on the main key fob for two seconds. The system automatically turns on or off at a distance of up to 35 meters from the vehicle. When operating the alarm in conditions of strong interference, this distance can be reduced to 15 meters.

The black oval highlights the hands-free mode icon

The hands-free mode can only be controlled using the main key fob with a display.

Auto engine start

When using automatic start, you need to remember and follow a few rules:

1. Autostart can only be used when the machine is placed in a ventilated area and subject to visual contact.
2. Produce automatic start prohibited when people are standing in front or behind the vehicle.
3. The parked car must be fixed with a working parking brake.
4. Before enabling the autorun feature on machines with manual method shifting speeds, it is necessary to set the "software neutral".
5. Monitor coolant or oil levels.
6. Set in advance on the microclimate control unit the direction of airflow and the desired air temperature in the cabin.
7. Do not pass the key fob to play with children.

Before turning on the engine start system on vehicles with a manual gearbox, the neutral position of the gearbox lever must be programmed. There are three options for this, the description of the steps for each of them is given below. The mode can be programmed through the system settings menu.

The first option provides:

1. Stop in a parking space, apply the parking brake, move the gearshift lever to neutral and remove the key from the lock cylinder.
2. With the engine still running, open the door, leave the vehicle and slam it behind you. The motor must stop.

If you need to pick up things from the trunk, then you should use the second option:

1. After setting the lever to the neutral position and turning off the ignition, the driver exits the car and does not close the door behind him.
2. Open the trunk and take out everything you need.
3. Close the door and then slam the luggage compartment lid. The engine will stop and be ready for automatic start.

The third option looks like this:

1. Set the neutral position and apply the parking brake.
2. Close doors.
3. Press button two on the key fob for two seconds.
4. Turn off the ignition and get out of the car.
5. Close the door, after which the motor will stop.

When installing autorun on the machine, the neutral setting procedure is not required, it is enough just to put the box selector in the parking mode.

To provide remote engine start, it is necessary to install a device to bypass the immobilizer.

The engine can be started by pressing the second key fob button. After starting the engine, the display will show the remaining operating time. This parameter is programmable and can be 45/25/15 or 5 minutes. If necessary, the car door can be opened by pressing the first button and within 20 seconds, insert the key into the lock and turn to the active ignition position.

Display in engine mode

Autostart by timer

To connect and disconnect the function, a short press on buttons three and four is used, after which the icon with the inscription Timer will turn on on the screen.

There are two options for working, which are configured programmatically:

• daily run, repeating every 24 hours;
• auto-restart every 2/4/8 hours.

To enable daily start, a so-called redundant mode must be carried out.

For this you need:

1. Turn off the timer mode by briefly pressing buttons two and four.
2. To enter the setting, press buttons one and two for a few seconds.
3. Turn on the mode by pressing 13 times on the button four. Each press will be accompanied by a signal.
4. Select the repeat time by pressing the buttons (the second button gives a repeat of 8 hours, the third - 4 hours and the fourth - two hours).
5. Enable timer.

Enable timer start

Auto start by battery temperature and voltage

The engine is switched on according to the temperature inside the cabin minus 15 or 25 degrees in winter time and plus 60 in the summer.

1. Turn off the timer start mode.
2. Press button four 21 times.
3. Use the buttons to select the switching threshold (the fourth - plus 60, the third - minus 25 and the second - minus 15).
4. Enable timer.

When setting the voltage to onboard network the system will operate at a value of 11.5 V.

1. Press 20 times on the fourth button.
2. Turn on voltage start with button two.

In all warm-up modes, you can vary the operating time of the power unit.

For this, the steps are:

1. Press button number four twelve times.
2. Select the operating time using the buttons from the first to the fourth, choosing each time from the range of 5-15-25-45 minutes.

Scher-Khan Magicar 5 alarm auto start malfunctions

The main causes of malfunctions that are possible when auto-starting the Sher-Khan Magikar 5 alarm:

1. The engine does not start even though automatic start backup is running normally. The cause may be oxidized fuse legs in the power supply circuit of the main unit. Another reason may be the failure of the standard immobilizer crawler or the sticking of the contacts in the control relay.
2. The motor starts and then stalls after a few seconds of operation. At the same time, in normal mode, the engine starts without problems from the ignition switch. One of probable causes there may be damage inside the five-pin relay installed in the main unit.
3. A common reason why the start does not work is incorrect parameter settings. To eliminate this, you must return the system to factory settings and re-program.
4. Sometimes the reason that the automatic start stopped working may be the inclusion of Valet mode. This mode is characterized by a permanently lit control diode. After the setting mode is turned off, the start returns to normal.

Wanting to understand how to enable autorun on Sherkhan 5, you should study the instruction manual, know the principle of operation and the modes implemented in this system car alarm. It is controlled by using a switching key fob with an LCD display, via a radio channel. Broadcasting of signals is carried out at a distance of up to 1.5 km.

The device is equipped with cars equipped with a gasoline or diesel power unit, with a voltage in the on-board network of 12 W. The alarm system has the option of automatically starting the engine by activating a command from the key fob or starting from a timer.

Preparation for work

How to enable autorun on Sherkhan 5 is presented below, but first the alarm must be prepared for work. Before you start using the key fob, you will need to perform certain actions aimed at its correct activation. The fact is that in order to maintain a full charge of the battery, manufacturers supply the power supply separately from the main device.

To install the battery in the provided compartment, you should carefully remove the latch that holds it in closed position cover of the respective compartment. Usually, this operation does not cause any problems, since the body and other elements of Sherkhan 5 are made of high-quality and high-strength materials.

The next step involves moving the key fob cover opposite to the antenna and placing the battery in the compartment with the polarity observed. After adequate installation of the specified part, a characteristic melodic sound should be heard, after which it is necessary to reinstall the cover and retainer.

Auto start setting

Enabling autorun is described in detail in the presented step-by-step instructions:
Button press modes differ in two ways (important):

• Short-term activation - a single impact on the key, lasting no more than a second, which is accompanied by a short signal;
• Long press - fixing the button for more than 2 seconds until a sound notification appears, after which you can release the key.

Further tuning of the engine excitation programming is shown using functions 1-12 for 25 minutes as an example. First you need to enter the settings mode No. 1, activate buttons 1 and 2 at the same time. Hold them until the remote control beeps. If the manipulation is carried out correctly, the alarm will be in the programming sector.

Next, you need to carry out successive touches of button No. 4 in the amount specified by the program. Each click must be confirmed a specified number of times. In this example, 12 clicks. At the end of activation, you should hold the button for 3-4 seconds, after which, the device will sound 12 notifications to confirm the programming item.

Features on a specific example

The autorun settings of Sherkhan 5 every 2 hours or when the temperature in the cabin drops to -15 ° C, with the cabin warming up for 25 minutes, perform the following manipulations:

• At the same time, buttons I and II are activated, then, pressing VI twelve times, at the end - holding the button III (functions 1-12 are configured taking into account the temporary value of 25 minutes);
• Activators I and II are pressed synchronously, button No. VI is clicked 13 times (alarm functions No. 1-13 are set to a time indicator of 2 hours;
• Perform pressing simultaneously I + II and VI - 21 touches (function 1-21 is set to a temperature of - 15 ° C).

To autostart Sherkhan 5 from the key fob, press and hold button II for at least 2 seconds, as shown in the figure.

ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!

In this case, the car will forcibly switch to armed mode with the engine running. The doors will automatically enter the close mode, after which the system will be set to the engine start mode. If the process of starting the engine is successful, then the key fob will display information about the time remaining before the engine stops working in minutes-seconds, and smoke from the exhaust pipe. This time can be programmed in the modes of 15, 5, 25 minutes or 45. To make a trip without stopping the engine within the programmed auto start duration, it is necessary to open the driver's door, then insert the key into the ignition lock, turn it to the "Ignition On" position. The period of time between opening the door and turning on the ignition mode is limited to 20 seconds. This event is provided in order to increase the security of the car against theft during the warm-up period. If within 20 sec. the ignition will not be turned on, the engine will stop.

If the engine start was unsuccessful, security system will try to start again. After the 3rd unsuccessful attempt, the car alarm will go into standby mode. To restore the autorun function, it is necessary to diagnose the engine and the main systems of the car. Possible reasons the fact that the engine autostart does not work:

• weak charge battery;
• extremely low temperature engine in the cold season;
• immobilizer problems limiting remote engine start;
• malfunction of the electrical equipment of the car;
• there is no control over starting the engine (the engine did not start, but there is smoke on the indicator, so a second attempt to start is not made);
• failure of other engine systems internal combustion associated with difficulty starting.

If the engine is started with the key, but the remote start does not work, it is necessary to reprogram the autostart system, reducing the starting frequency, increasing temperature regime triggering. Perhaps the problem will be fixed.

When starting the engine, the security system will signal the following signals.

The car is not set to autorun, if during its production:

• the ignition is in the "On" position;
• one of the doors is open;
• the engine is already running;
• the "reserve" mode is not activated in cars with manual transmission.

In the event of a successful engine start, the devices will signal:

In the case when the engine stops automatically, the devices generate signals:

Programming autorun time intervals

The car alarm provides programming of time intervals (autostart time) after two, 4 and 8 hours. The choice of a specific option is made depending on the operating conditions of the car, the condition of the engine and the battery. To start the programming operation, it is necessary to simultaneously long press the buttons I and II. Next, you need to perform the following operations in the following sequence:

1. Turn off the “timer” option (if it is activated) by briefly pressing buttons II and IV at the same time. The "timer" should be deactivated on the display.
2. Press the IV button thirteen times. Each entry is confirmed by one siren signal.
3. Wait for the siren to give a 13-fold sound confirmation of the entered information.
4. Use the key fob buttons to confirm the selected autorun mode. Button II corresponds to the autostart mode after 8 hours, III - after 4 hours, IV - after two hours.
5. Set to autostart by turning on the "timer" mode by briefly pressing buttons II and IV at a time.

Reprogramming the autostart mode according to the interior temperature

For correct activation of autostart according to the characteristics of the passenger compartment temperature, it is necessary to activate the start modes by time (1-13) before enabling the programming option. Next, you need to switch to the programming mode by long pressing the corresponding buttons on the key fob I + II. Then the following operations are performed:

1. Turn off the "timer" mode (if it is activated), as described in the previous paragraph.
2. 21 times methodically press the IV-th button, after which the siren will signal.
3. Wait for the siren alarm 21 times in a row.
4. Set the desired autostart temperature mode: button IV - plus 60 degrees Celsius, III - minus 25, II - minus 15.
5. Activate the timer mode.

Warm-up programming

The warm-up time can be set to fixed intervals of 5, 15, 25 minutes or 45 minutes. To do this, activate function 1-12 in mode II. Programming is entered by long pressing I + II, after which the following operations are performed:

1. Button IV is pressed twelve times (accompanied by a sound signal).
2. 12-fold siren signal - confirmation.
3. The engine operation time is selected by activating buttons I (5 minutes), II - 15, III - 25 or IV - 45 minutes.

Programming autostart by the voltage of the on-board network

Autostart can be programmed when the battery is discharged to an amplitude of 11.5 volts. First you need to activate the start by time (1-13), then enter the programming by long pressing I + II. Here are the buttons to press:

1. 20 consecutive IV button presses.
2. Waiting for the siren to sound 20 times.
3. Activate the battery voltage response mode with button II.

Autorun problems

Some vehicles have the following autostart problems:

1. When the ignition is turned off, the car does not stall. To disable autorun, you need to open and close the doors. To correct the problem, function 1-16 (Button II option) is required. In this case, in order to turn off the engine, it is necessary to switch the key to the "Ignition Off" position.
2. Activation of the "Valet" mode after an emergency removal from the alarm system (zzzz symbols on the key fob). To fix the problem, simultaneously long (more than 2 seconds) press the I + III buttons.
3. If it is necessary to urgently turn off the car from the key fob during the autostart period, it is necessary to long press the II button.