The issue of delineating space in the office can arise at any time. The need for redevelopment may not always be accompanied major repairs or global redevelopment of the premises. All this requires serious financial investments, causes inconvenience to the staff, and often there is a need to move to another room for a while.

Installation office partitions allows you to solve these problems quite simply and quickly.

- Installation of partitions can take only a few days - there is no need to interrupt the work process and disturb employees.

- Experienced craftsmen are able to install the structure in the room as quickly as possible, without causing inconvenience to office staff.

- Another undeniable advantage of such a product is that you avoid “wet” and dirty work during installation in your premises.

Stages of installing office partitions

Installation of partitions of any configuration takes place in several stages, which must be followed in a certain sequence. Before starting the main work, the ceiling and floor profiles are securely fastened, for which screws of various sizes are used.

Installing office partitions is quite simple and does not require a long time. If the design is simple and the area of ​​the room is small, then all work can be completed in one day.

Of course, before installation it is necessary to study the room, take into account all its features (level of ceilings, curvature of walls, possibility of fastening and other nuances). You should foresee in advance whether there will be a need to install an office partition to the ceiling. Experienced master will be able to assess the parameters of the premises and advise the customer which type of structure is best to purchase. As a rule, optimal standards partitions are 4 meters, but you can also find models up to 10 meters high.

The installation of partitions begins with the installation of the frame, then the finishing panel is installed. It is extremely important to ensure proper strength of the structure and protect it from mechanical damage. For this they use metal profile, which is mounted in the lower half of the partition. This approach significantly enhances the performance of the product, while appearance equipment remains aesthetically attractive.

The choice of fastening is one of important points, which should be taken into account when installing partitions in the office. Make decisions in favor a certain model possible based on the following indicators:

• dimensions of the structure (width, height, length);
• features of the premises;
• type of partition being installed.

Make a selection of partitions:

Cost of installing office partitions

Perhaps someone considers it advisable to save on equipment installation. Installation of office partitions is not considered difficult, but it is preferable to contact specialized organization, which will provide a team of workers.

The company "SteelOffice" is one of them. Our staff includes experienced craftsmen who are ready to implement a project of any level of complexity. Installation of office partitions is one of the main services provided by our company.

Please note that the company "SteelOffice" installs structures only from its own materials

As a rule, the final price for installing office partitions depends on the following factors:

• level of design complexity;
• room area;
• type of installation;
• design features partitions;
• the material from which the product is made.

You can call our specialist to the site and calculate the cost of the order yourself. We are also always happy to answer your questions about installation glass partitions, if you call us or request a call back.

Do you need installation of office partitions at an affordable price? We are at your service! Affordable price, quality work, quality guarantee – extremely favorable terms of cooperation from the company "SteelOffice".

Installation of partitions by specialists of the company "SteelOffice"

The safety of its use depends on how correctly the structure is installed. An experienced technician will always check the strength of its fastening and make sure that the equipment is ready for further use.

The SteelOffice company offers services for installing office partitions in any type of room.

The team of workers is provided modern equipment and that's all necessary components. This allows you to complete work quickly, efficiently, and efficiently. The installation of partitions is carried out according to a certain scheme, taking into account the design features and the room in which the product will be used.

You can view a portfolio of our work in the interactive gallery. Shown in the photo real results installation of glass partitions in various types office, which were produced by the company's craftsmen "SteelOffice".

We are always happy to help you do right choice products depending on personal preferences and financial capabilities. Designers and planners will evaluate the features of the room and recommend best option partitions.

*Calculations use average data for Russia

Currently, during the construction and redevelopment of premises, plasterboard partitions are very often used. They are convenient for both residential and office spaces.

Advantages of plasterboard partitions using the example of a standard office

Office partitions are designed in such a way that in the conditions of being large number workers in one room, each of them had their own kind of office.

Thus, one rather large room, in itself not very convenient for individual work(other people distract the worker visually and with noise) turns into a sufficient number of cells, such as small offices, separated on at least three sides.

In addition, in this way, for example, the confidentiality of negotiations with visitors is optimized - the walls isolate the clerk and his client from outsiders.

Currently, plaster, foam concrete or aerated concrete are very often used for the construction of capital partitions. With all their undoubted advantages, they also have several significant disadvantages: such office partitions are non-removable, quite heavy and cumbersome, which may not have the best effect in the best possible way on floors, especially if the building is old - because the weight of the partitions creates additional load on them.

In addition, floors and walls are subjected to fairly deep (about 10 cm) drilling. But the main disadvantage of plaster office partitions is that when they are dismantled, quite serious repairs will have to be made to eliminate traces of their presence in the room.

It is because of the above factors that many organizations prefer to purchase office partitions made of plasterboard or glass-magnesite sheet. The differences between these two materials are insignificant, except that FMF (glass-magnesite sheet) bends a little better and is more resistant to moisture.

Earn up to
200,000 rub. per month while having fun!

Trend 2020. Intellectual business in the field of entertainment. Minimum investment. No additional deductions or payments. Turnkey training.

Installation of plasterboard partitions takes a little longer than the previous ones, but this factor is not an obstacle to many advantages: partitions of this type are lightweight and do not require special processing and alignment after installation, all communications fit freely inside the partition - electrical wiring, telephone and network cables, etc.

In addition, for the manufacture of plasterboard (glass-magnesite) structures, access to water is not required (as for plasterboard, foam concrete and aerated concrete, which are fastened together special solutions, mixed with water on site).

Installation of an office partition made of plasterboard

The actual installation of a plasterboard partition consists of two stages. At the first of them, in accordance with a previously approved scheme, a frame for future partitions is constructed from a special galvanized profile. Main (load-bearing) vertical and horizontal elements attached to the floor and walls (and also to the ceiling if the partition reaches it).

Thinner and lighter elements fill the resulting frame in the form of a lattice with a cell of approximately 50x50 cm. They serve as a reinforcing structure - the plasterboard partition itself is hollow inside.

At the second stage, the actual plasterboard (glass-magnesite) sheets are attached directly to the resulting frame. The second stage, as a rule, is shorter than the first, and the entire cycle (for partitions, for example, with a height of 1.5 m and a total length of 20 m) will not take more than 2 days for 2 people.

Costs for the production of plasterboard partitions

The customer pays for the consumables, so their cost is insignificant for the calculation net profit. The tool costs are:

1. Impact drill 2 pcs. - only 7788 rub.
2. Universal drill set 2 pcs. - only 622 rub.
3. Cordless screwdriver 2 pcs. - only 14286 rub.
4. Set of bits for screwdriver 2 pcs. - only 1158 rub.
5. Measuring tape 2 pcs. - only 494.76 rub.
6. Electronic level 1 pc. - 5500 rub.
7. Knife for cutting drywall 1 pc. - 108.26 rub.

TOTAL: RUB 29,957.02

Ready ideas for your business

Production cost of 1 sq. m of an ordinary partition made of plasterboard (i.e. without insulation and 1 layer of material on each side) - as a rule, from 350 to 400 rubles. depending on the region.

Moscow, metro station Rumyantsevo

Job responsibilities:

Requirements:

• it's in your blood

WE DEFINITELY WILL NOT WORK IF:

We offer:

Send your resume:

Sales Manager (office partitions, doors), St. Petersburg

Salary from 50,000 to 120,000 rubles.

Saint Petersburg

Full-time work at the employer's premises
Work experience from 1 to 3 years, secondary education

Job responsibilities:

Full project support - from the incoming application to the closing documents.

• Receiving a call or processing an application from the website (WITHOUT active sales, but initiative is welcome), initial consultation
• Selection of options, cost calculation and formation of CP (all calculations, setting tasks, drawing up contracts, etc. in automatic mode in your own CRM system, including graphic images in KP)
• Preparation of contracts and invoices, pushing the client until payment, handling objections
• Launch into production (specifications for materials are generated automatically based on the initial calculation in the CP), generation of applications to suppliers, request for invoices for payment (for those items that are not in stock)
• Monitoring compliance with deadlines from production, delivery and installation departments
• Preparation of closing documents

Requirements:

WE ARE SUITABLE FOR EACH OTHER IF:

• You know how to sell and you like it
• it's in your blood
• You have worked in direct sales for more than a year and can confirm this with results in numbers (funnel, conversion, average bill, profitability, etc.)
• You are a pleasant person and easy to talk to
• Learn yourself, and don’t wait for them to explain. Love to think to figure something out
• You see opportunities in everything and look for solutions.
• You look presentable, speak fluently and do not make gross grammatical errors
• You understand how to install Windows, know how to use formulas in Excel, and know the main differences between a Mac and a PC
• Do you want creativity, you like to create and you love construction sets
• Like nice interior, you are interested in new products and you simply have taste

WE DEFINITELY WILL NOT WORK IF:

• You are not looking for solutions, but making up excuses.
• Constantly whining that something is wrong
• Do you think that selling is a “sell”?
• A stable salary is more important to you than the opportunity to earn money
• You didn't make any progress on previous work, but we are sure that now it will definitely work out!
• You sincerely believe that production runs like clockwork, without failures, and customers stand in line and hope for your attention

We offer:

We are engaged in the development, production and installation of modular partition and door systems. We have many of our own developments, but we also use ready-made solutions from major suppliers (Petralum, Freestyle, Alutech, etc.). We have own production and a warehouse in St. Petersburg (and regular shipments of orders to Moscow).

We have 2 main sales offices - in Moscow and St. Petersburg, as well as 18 dealers in the regions. The monthly flow of incoming requests is at least 350 pieces. with a conversion to order of 11%, an average receipt of 188 thousand rubles. and profitability of at least 40%

We offer: at least 30 requests per month and a rate of 20% of the profit (i.e., if you meet the average indicators for the company, you can safely count on the following salary: 30 x 11% x 188 thousand rubles x 40% x 20% = 49630r.). There are several people in the company who earn less than 100 thousand rubles. They don’t earn money in principle, but there are those for whom it’s 35-50 thousand rubles. that's enough too. But they are also valuable to us for their experience and skills.

Your undeniable advantage will be experience in a similar field - modular partitions (ideally) or windows, doors, office furniture. Or you will have to undergo training yourself (5-day video course with a description general principles work, design features of partitions, as well as work in the CRM system (calculation of the cost of partitions, drawing up CP, launching into production, etc.))

Send your resume:

Partition installer. Salary by agreement. Saint Petersburg

Responsibilities

Installation of partitions (Double and single glazing. Profile systems Alutech and Petralum):

• Mobile partitions (assembled and disassembled)
• Installation of partitions from a whip (Freestyle profile).
• All-glass partitions (on a clamping profile or point fastenings)
• Plumbing partitions (chipboard, plastic, glass)
• Sliding and fire partitions (with supervision of installation)

• Reception desks (with aluminum frame)
• Office furniture (cabinet + chairs)
• Independent delivery of work to the customer (coordination of controversial issues and quality control)

Requirements

• Experience as an installer (gypsum board partitions, stained glass, metal-plastic windows, cabinet furniture, interior doors...)
• Age from 20 years, physical strength, without bad habits(strictly alcohol), neat appearance.
• Having your own tool
• Car (preferred)
• Having a partner
• Willingness to travel (possibly staying on site or in a hotel)
• Driving license category B

Terms

• Payment - piecework (prices - according to the price list, payment on the day of delivery of the object, bonuses for letters of recommendation from clients)
• Full time
• Traveling character

Partition work with training Partition vacancies with training in Moscow. Partition vacancy with training from direct employer in Moscow advertisements for partition work with training Moscow, vacancies of recruitment agencies in Moscow, looking for partition work with training through recruitment agencies and from direct employers, partition vacancies with training with and without work experience. Advertising site for part-time work and work Avito Moscow work vacancies partitions with training from direct employers.

Work in Moscow partitions with training

Website work Avito Moscow work fresh vacancies partitions with training. On our website you can find high paying job partitions with training. Look for partition work with training in Moscow, view vacancies on our job site - aggregator of vacancies in Moscow.

Avito vacancies Moscow

Partition work with training on the site in Moscow, partition vacancies with training from direct employers in Moscow. Jobs in Moscow without work experience and highly paid ones with work experience. Partition vacancies with training for women.