Supporting materials. Thermal insulation adhesive Application of K-FLEX k414 adhesive

Glue
Installation of all brands of thermal insulation and K-Flex coatings is carried out adhesive connection using special glue. Detailed description For brands of adhesives, see the text below.

Very Important!
The glue must be mixed before application, even if you used it yesterday.
After applying the glue to the material, you need to wait a short time (50-90 seconds). Glue applied to the surface of thermal insulation will dissolve it at the micro level and begin to polymerize.
When the dried glue reaches a state similar to the sticky layer on the tape, gluing can be done.
As a result of proper gluing, you will receive a “cold welding” type connection.

To reduce the drying time of the glue, as well as when gluing materials at temperatures close to 0°C, it is recommended to add up to 10% K-Flex cleaner to the glue

.
It is not allowed to install thermal insulation on tape without using glue; this is a violation of the technology for installing thermal insulation.
Carrying out installation work described in detail in the section

Cleaner K-Flex consists of a mixture of solvents and is used for cleaning surfaces before applying glue, cleaning glued materials from glue residues to give them an aesthetic appearance, cleaning tools, diluting thickened 414 glue or using it for gluing at slightly negative air temperatures.

Specifications

ALCLAD, ICCLADSR, ICCLADBK.

Heat can be successfully used for gluing insulating materials based on polyethylene, for example Energoflex, Tilit, Thermaflex

Adhesive K–FLEX 425 is a two-component contact adhesive based on polychloroprene rubber and filler and is intended for gluing coatings INCLAD and thermal insulation of the SolarHT brand.

Main technical characteristics

Adhesive K-Flex 467 - winter

Contact adhesive based on polychloroprene rubber for gluing all brands thermal insulation K-Flex and coatings ALCLAD, ICCLADSR, ICCLADBK.

Main technical characteristics

Adhesive K-Flex K-414 price

Glue k-flex k-414 0.5 lt price 434.24 RUR

Glue k-flex k-414 0.8 lt price 620.07 RUR

Glue k-flex k-414 2.6 lt price 3632.54 RUR

Glue consumption
300 ml per 1 sq.m. surface to be glued.

TECHNICAL CHARACTERISTICS K-FLEX K-414

It was specially developed by Italian engineers for gluing insulation from foam rubber of the K-FLEX brand. Adhesive K-Flex 414 is resistant to ultraviolet rays. The surfaces glued together with glue 414 acquire the characteristics of the material itself.

K-FLEX K414 adhesive is one-component contact glue, which is based on polychloroprene rubber.

The adhesive is intended for gluing K-Flex thermal insulation and AlClad, InClad coatings. The optimal application temperature is 15-20 0 C. The glue is produced in metal containers with a volume of 0.2; 0.5; 0.8 and 2.6 liters.

When insulating cold surfaces, K-FLEX glue should be applied to the insulated surface and the surface of heat-insulating products. The consumption of K-FLEX K-414 glue in this case is 0.3 liters per m² of surface to be glued.

1. Application temperature affects viscosity and drying time.
2. High humidity affects the strength of the seam.
3. Temperatures below the dew point must be avoided.

In order to glue the seams of thermal insulation products, K-FLEX glue must be applied evenly to both surfaces to be glued. The surfaces to be glued can be connected within 3-5 minutes. When gluing seams, the surfaces should be pressed tightly together.

Application of K-FLEX k414 glue

The adhesive composition is mainly used in heating systems, drainage systems, water supply systems, and heating points. It is designed for gluing insulating materials, suitable for IC CLAD BK and SR or IN CLAD, AL CLAD coatings.

Glue K-FLEX K-414 resistant to external influences, and does not lose its qualities under the influence of temperature changes, atmospheric phenomena. The adhesive composition is resistant to aging and has long term operation. Keeps its quality characteristics at temperatures -40…+105 °C. The viscosity of the glue at 23 °C can be in the range from 550 to 750 MPa, the density of the composition is 0.85 g / cubic meter. cm.

The use of glue is allowed at positive temperatures (from 5 to 30 °C). After applying the composition to the surfaces, they are firmly glued together and acquire the high-quality properties of the original insulating material. The product warranty period is 1 year when stored at a temperature of +15…+25 °C.

Specialized one-component adhesive for contact connection and fixation of rubber-based insulating materials. Possesses high efficiency and allows you to glue the surface in the shortest possible time.

Adhesive K-FLEX 414 volume 0.5 liters, is one of the most optimal adhesive composition ov in its line, due to its small volume. The lid is removed from the jar and the glue is ready for use.

Line of adhesive composition glue K-FLEX 414 and their volumes
√ 0.5 liters - with a metal lid. After opening, it is ready for use.
√ 0.8 liters - with a metal lid. After opening, it is ready for use.
√ 2.6 liters - with a plastic red lid for large volumes of work. To use, it requires pouring into an additional container.

Important! If K-Flex 414 glue thickens, it can be brought back to life using a K-FLEX brand cleaner.

Application
√ for connecting rubber tubes of any diameters and thicknesses
√ for gluing rubber rolls of various thicknesses
√ for fixing to the surface of AL Clad and IC Clad coatings.

You can send your application with payer details by email

Pay attention! The price is per piece.

Don't forget to buy a cleaner with K-FLEX glue!

K-Flex glue is a necessary component of the high-tech pipe thermal insulation system of the same name. There is a plant for the production of K-Flex elastomeric products in the Moscow region. This is equipped with last word production techniques with strict product quality control.

Types of K-Flex glue

The adhesive composition is available in two versions:

• single-component rubber-based products;
• two-component, including filler.

Thermal insulation material of this brand is used:

• for insulation of pipelines in heating and water supply systems;
• for creating tight connections in air ducts.

We sell various packages of K-Flex glue, ranging from 0.22 to 2.6 liters. A variety of release forms allow you to purchase required quantity product.

Rules for using glue

• use at temperatures from +5 to +30 ºС;
• stir thoroughly before use;
• in case of thickening - dilution with K-Flex cleaner;
• applying a uniform thin layer to both surfaces to be bonded, previously degreased and dried;
• strong compression of surfaces after joining.

The two-component composition is used in the same way.

Advantages of K-Flex adhesive

This material is in high demand among consumers due to its many advantages. Among them:

• economical consumption;
• reliable bonding of surfaces without modification technical characteristics thermal insulation;
• resistance to aging and influence atmospheric influences;
• rot resistance;
• waterproof.

Numerous studies have proven that bonded surfaces retain their properties throughout the entire period of operation, which is 20 years.

We offer to order K-Flex brand glue with delivery. The TERMA-MSK company is the official representative of the manufacturer, therefore it forms the most favorable prices for this product. Call to place an order!

K–FLEX K414 adhesive is a one-component contact adhesive based on polychloroprene rubber and is intended for gluing K–FLEX products and AL CLAD, IC CLAD SR and IC CLAD BK coatings.

Transportation and storage:

Adhesive K-FLEX K-425

K–FLEX K425 adhesive is a two-component adhesive based on polychloroprene rubber and a hardener.

Transportation and storage: At temperatures from +10 °C to +30 °C, avoid direct contact sun rays. It is allowed to transport products at sub-zero temperatures; in case of freezing, the glue restores its original consistency and properties at room temperature within 24 hours, and the jar must be closed. Guaranteed shelf life in original containers is 12 months from the date of manufacture.

Adhesive K-FLEX K 467

K–FLEX K467 adhesive is a one-component adhesive based on polychloroprene rubber. The adhesive is “contact” and is recommended for installing foam and synthetic rubber insulation on pipes and common surfaces located in heating and cooling systems.

Transportation and storage: At temperatures from +10 °C to +30 °C, avoid direct sunlight. It is allowed to transport products at sub-zero temperatures; in case of freezing, the glue restores its original consistency and properties at room temperature within 24 hours, and the jar must be closed. Guaranteed shelf life in original containers is 12 months from the date of manufacture.

* - If the installation temperature is below +10 °C, you must contact the specialists of K-FLEX LLC.

Products are certified. The certificate can be downloaded

Designed for sealing seams protective coatings AL CLAD, IN CLAD And WHITE CLAD when placing objects outdoors.

Transportation and storage: At temperatures from +5 °C to +30 °C. The guaranteed shelf life of sealant in cartridges (0.290 l) is 18 months from the date of manufacture.

Products are certified.

The glue dispenser is designed for uniform and accurate application of glue. The main advantages are reduced losses, reduced amount of working time during the process of applying glue, high speed of glue application.

K-FLEX cleaner is a mixture of organic solvents and is intended for cleaning bonded surfaces, cleaning tools (brushes, spatulas, rollers) and diluting thickened glue.

Available in 1 liter containers.

Transportation and storage: At temperatures from +10 °C to +40 °C, avoid direct sunlight. Guaranteed shelf life in original containers is 18 months from the date of manufacture.

Acrylic paint on water based, odorless, easy to apply and dries quickly, does not pollute environment and does not fade. Used to cover insulation both indoors and outdoors, excluding UV exposure. Available in 2.5 liter capacity. Paint consumption is 0.45-0.5 l/m2 in two layers.

Transportation and storage:

Products are certified. The certificate can be downloaded.

Water-based acrylic paint, odorless, easy to apply and dry quickly, non-polluting and non-fading. Used to cover insulation both indoors and to repair the K-FLEX COLOR system. Available in 0.5 l volume. Paint consumption is 0.45-0.5 l/m2 in two layers.

Paint color - white, gray, beige, black, green, red, blue.

Transportation and storage: At temperatures from +5 °C to +30 °C, avoid direct sunlight. Avoid freezing. Guaranteed shelf life in original containers is 12 months from the date of manufacture.

Products are certified. The certificate can be downloaded.

Designed for punching holes in K-FLEX AL CLAD and PVC coatings for its further fixation with K-PACK rivets. Has a plastic handle.

Rivets K-PACK are made of PVC and are intended for mechanical fastening of longitudinal and transverse overlaps of PVC, AL CLAD and WHITE CLAD coatings.

Packaging (1000 pcs.)

Plastic clips are intended for temporary fastening of longitudinal and transverse seams of thermal insulation made of K-FLEX PE foam polyethylene to ensure complete adhesion of the taped insulation seams to each other.
Packaging (100 pcs.)

A special capping tape is necessary for neat finishing of the ends insulated pipes. For ease of identification of pipes in the system, plugs are produced the following types: silver, gray, red, blue. End cap length 10 m.

Example 18 x 32: where 18 mm is the length of the petals, and 32 mm is the width of the blanking tape, installed at the end.

Designed for mechanical fixation K-FLEX plates to non-horizontal surfaces.

The mounting knife is designed for cutting K-FLEX tubular material.
Allows you to make a smooth cut without torn edges.

Bag with tools for installation of K-FLEX materials

Equipment:

• Universal calipers for external measurements;
• Metal compasses, at least 400 mm long, in a case or with a protective cap;
• Assembly knife, with a steel, narrow, long blade of at least 300 mm with a rounded end;
• Utility knife, 150 mm, offset blades;
• Sharpening stone for sharpening knives 225 mm or musat (sharpening) with a length of at least 300 mm;
• A miter box having at least three cutting angles of 22.5°, 45°, 90° and a width work surface not less than 120 mm;
• Radiator brush, with short, stiff bristles, at least 38 mm wide;
• The brush is flat, with short, stiff bristles, 22 mm wide;
• Varnish marker, with round (bullet) tip white, with line width: 1-2 mm;
• Tape measure 3 meters, in a rubberized case with 3 latches.