The VERSO series is divided into two groups: VERSO Standard, which is a standard series of installations, and VERSO Pro, which is designed for special projects. Both groups of units can be offered with rotary heat exchanger, heat pump and rotary heat exchanger, plate heat exchanger or simply air handling units.
Installation Komfovent Verso R 2500-H-E differs not only optimal parameters work, but also with compact dimensions: design features in VERSO Standard and VERSO Pro units allow limiting the dimensions of one of the sides of the section to 900 mm, which makes it possible not to exceed the dimensions of a standard doorway.
All standard settings Verso Standard are based on the “PLUG AND PLAY” principle: each unit has fully integrated control automation. Verso Standard units can be shipped to the customer for quite short term as they are available from stock. Ventilation units have a capacity of 1000 to 8000 m³/h.
Verso Pro units have wide opportunities, customer can choose desired setting using software. For the convenience of customers, air heaters, air coolers and dampers are installed on outside installations - as separate sections, so the assembly of the device is greatly simplified, and the installation site of the device is saved effective area. VERSO ventilation units can be mounted both indoors and outdoors. The units are manufactured with fully integrated control automation. The capacity of the units ranges from 1000 m³/h to 34000 m³/h.
Benefits of Verso R units:
- Saving thermal energy
During the ventilation process, the heat from the exhaust air is transferred to the air entering the room. - Efficient heat exchanger
Under normal conditions, the rotary heat exchanger does not freeze over: additional heating supply air not needed even if the outside temperature drops below zero. Using a rotary heat exchanger, the energy consumption for air heating is reduced by approximately 4 times. - Air humidity balance
Under normal conditions, condensate does not form in rotary heat exchangers, since excess moisture removed, and part of the moisture is returned back to the room. The air in the room is less dehumidified, so the humidity balance is maintained. Condensation does not fall out, drainage is not needed, all this simplifies the installation of the unit. - Low noise
The Verso R ventilation units are equipped with low-noise fans housed in a sound-insulating housing. This provides low general level noise.
Benefits of a rotary heat exchanger
- High efficiency
- Does not freeze
- Four times less energy for air heating
- Regenerates moisture – reduces humidification costs
- No drainage required - installation of the unit is simplified
- Compact
- When the air conditioning is on, returns the cold from the exhaust air - reduces air conditioning costs
Temperature efficiency on demand:
Two levels of rotor efficiency are possible. Optimum efficiency is achieved with the L type rotor, more than high efficiency available with XL type rotor.
Ventilation units are manufactured with rotary heat exchangers of three types:
- Heat exchanger from aluminum foil(AL). It regenerates moisture in winter;
- Heat exchanger made of hygroscopic and aluminum foil (AZM). It regenerates moisture more efficiently than an AL type heat exchanger;
- Heat exchanger made of hygroscopic aluminum foil (AZ). This type of heat exchanger effectively controls humidity in both winter and summer.
Energy efficient EC motors
All rotary heat exchangers are equipped with EC motors, which save energy and ensure smooth rotation and control of the rotor.
Heater
For additional protection system, in conditions where the outdoor air temperature can be below -30 °C, it is recommended to install an air duct pre-heater.
Benefits of Verso R units
Saving thermal energy
During the ventilation process, the heat from the exhaust air is transferred to the air entering the room.
Efficient heat exchanger
Under normal conditions, the rotary heat exchanger does not freeze over: additional heating of the supply air is not needed even if the outside temperature drops below zero. Using a rotary heat exchanger, the energy consumption for air heating is reduced by approximately 4 times.
Air humidity balance
Under normal conditions, condensate does not form in rotary heat exchangers, as excess moisture is removed, and part of the moisture is returned back to the room. the air in the room is less dehumidified, so the humidity balance is maintained. Condensation does not fall out, drainage is not needed, all this simplifies the installation of the unit.
Low noise
The Verso R ventilation units are equipped with low-noise fans housed in a sound-insulating housing. This ensures a low overall noise level.
Rotary heat exchanger
Benefits of a rotary heat exchanger
- High efficiency
- Doesn't freeze.
- Four times less energy for air heating.
- Regenerates moisture - reduces the cost of moisturizing.
- Drainage is not needed - installation of the unit is simplified.
- Compact.
- When the air conditioning is on, it returns the cold from the exhaust air to the room - reduces the cost of air conditioning.
Thermal efficiency on demand: Two levels of rotor efficiency are available. Optimum efficiency is achieved with the L type rotor, higher efficiency can be obtained with the XL type rotor.
Ventilation units are manufactured with rotary heat exchangers of three types:
- The heat exchanger is made of aluminum foil (AL). It returns moisture.
- The heat exchanger is made of hygroscopic and aluminum foil (AZm). It returns moisture more efficiently than an AL type heat exchanger.
- The heat exchanger is made of hygroscopic aluminum foil (AZ). This type of heat exchanger returns moisture most efficiently.
Energy Efficient EC Drive
All rotary heat exchangers are equipped with an EC drive, which saves energy and ensures smooth rotation and control of the rotor.
For additional protection of the system, in conditions where the outdoor air temperature can be below -30oC, it is recommended to install an air duct pre-heater.
Control automation
C5 automation functions:
- 5 different working modes: Comfort1, Comfort2, Economy1, Economy2 and Special
- Temperature control: supply air, exhaust air, indoor, balance
- The user is provided with not only the main, but also the energy parameters of the device operation: heat exchanger efficiency, heat exchanger return energy, heater energy consumption counter, fan operation time counter
- Air quality control, minimum temperature maintenance
- Flow control modes: CAV, VAV, DCV
- Weekly plant program
- Air flow display (m³/h, m³/s, l/s)
- Protection of a rotary or plate heat exchanger against malfunction
- Rotor cleaning function
- Intelligent self-diagnosis
- Night cooling in summer
- Air quality control
- Supply air temperature control
- Maintaining the minimum supply air temperature
- Combined water heater and cooler control
- Inverter type outdoor unit control
- Cooling recovery function
- Outdoor ventilation compensation
- Humidity control: air humidification and dehumidification
- Control of circulation pumps on demand
- Warm-up function circulation pumps and mixing valves
- Clogged air filters indication
- Operating mode and energy meters
- remote control via web interface
- Built-in data logger for all air handling parameters
- Application software for smartphones based on "Android" and "iOS"
Modern technologies provide a person with a lot of opportunities to create a comfortable environment not only at home, but also in places of leisure or in the workplace. However, all the efforts of designers may be in vain if the microclimate of the room is not comfortable for those in it. To avoid such annoying mistakes, need install air handling units.
Diversity model range climatic equipment Komfovent Verso standard or special purpose allows you to adjust the flow fresh air in the mode you need - submission clean air, heating it to the desired temperature, humidifying or dehumidifying. Ventilation units industrial use they process air masses of much larger volumes, removing air polluted by industrial dust or gases from the premises and replacing it with clean air.
Each Verso ventilation unit differs in optimum parameters of work and is delivered in complete form. The dimensions of the equipment allow you to easily carry it through doorways and use it immediately after installation.
The advantages of using climate equipment of this trademark obvious:
- reducing the cost of heating a room, regardless of its area;
- long service life;
- increasing the productivity of production workers in comfortable conditions;
- increase in buyers and visitors of commercial structures.
Considering the benefits and specifications of each model, it should be noted that the housings of the R, P and CF series units are distinguished by excellent soundproofing qualities and, in combination with low-noise fans, make the operation of the unit almost silent. Series unit designs Verso R equipped with a rotary heat exchanger and have a capacity of 240 to 8000 m3/h.
In installations Verso R a plate heat exchanger was installed, which ensures efficient heat exchange due to the separation of air flows.
Models Verso RHP, except for rotary heat exchangers, are also equipped with a heat pump. This solution makes it possible to achieve high application efficiency, which is confirmed by a capacity of up to 1500 m3/h.
Series systems Verso CF with a counterflow plate heat exchanger have a capacity of up to 3500 mm3/h.
Although Air handling units Verso S have absolutely small size, it is the most efficient unit with an air capacity of up to 4000 m3/h. Its design provides easy installation and easy maintenance.
For the convenience of users, all series are equipped with modern consoles, which display detailed information about the operation of the system and it is possible to select the optimal operating mode. Also, the equipment has advanced features in the form of remote control.
Modern automation system installed on ventilation systems , increases economy and speed of each executed process. It allows you to provide for the operation of the equipment in different modes, maintain the set temperature, prevent the air heater from freezing, and much more.
At Panoramavent you can find not only the necessary brand HVAC equipment Komfovent, but also to make a purchase on attractive terms. Our experts will help you choose the appropriate size of the installations, taking into account the requirements of the customer and the parameters of the room. Buy air handling units Komfovent Verso we have - simple, profitable and reliable!
Price: 650,000 rubles including VAT
650000 RUB
KOMFOVENT VERSO R ventilation units presents a wide range standard ventilation devices with a rotary heat exchanger. Installation data...
Ventilation units KOMFOVENT VERSO R represents a wide range of standard ventilation units with a rotary heat exchanger. These units are equipped with high efficiency EC type fans. All equipment of the VERSO R series is equipped with built-in C5.1 automatic control, and the client receives an air handling unit with a fully configured and integrated automation control inside the unit, as well as an external modern wall panel. air capacity ventilation units VERSO Standaet R series from 1000 to 7000 m³/h.
Contemporary digital control settings allows the user to independently quickly and easily select and change the desired functions, control the parameters of the ventilation device directly from the control panel.
VERSO R series ventilation units with heat recovery, characterized by compact dimensions and wide choice functions, provide comfortable conditions in residential, public and industrial premises. In the production of ventilation devices of the VERSO R series, original designs, best materials and the latest technology, so this series of equipment is economical, safe, durable and trustworthy.
You can choose from four payment options:
- when placing an order through the website;
- Payment by bank card VISA International, Mastercard Worldwide and MIR office and retail outlets;
- Payment in cash to the courier upon receipt of the goods;
- Payment by bank transfer (for legal entities);
- Payment via Sberbank: You can pay for the order at any branch of Sberbank. For the money transfer service, you will be charged from 3 to 7% of the order value, depending on the region. The transfer of money will take about 10 days.
Payment by credit card through the website
To select payment for goods using a bank card on the corresponding page, you must click the button "Payment for an order with a bank card".
Payment is made through PJSC SBERBANK using Bank cards of the following payment systems:
- VISA International
- Mastercard Worldwide
Description of the data transfer process
For payment (entering your card details), you will be redirected to the payment gateway of PJSC SBERBANK. The connection with the payment gateway and the transfer of information is carried out in a secure mode using the SSL encryption protocol. If your bank supports the technology safe conduct Internet payments Verified By Visa or MasterCard SecureCode, a special password may also be required to make a payment. This site supports 256-bit encryption. Privacy Reported personal information provided by PJSC SBERBANK. The entered information will not be provided to third parties, except as provided by the legislation of the Russian Federation. Making payments for bank cards carried out in strict accordance with the requirements of the payment systems MIR, Visa Int. and MasterCard Europe Sprl.
The transferred funds are returned to your bank account within 5-30 working days (the period depends on the Bank that issued your bank card).
Please note that this website is for informational purposes only and under no circumstances information materials and the prices posted on the site are not a public offer, determined by the provisions of Articles 435 and 437 of the Civil Code of the Russian Federation.
Your order, including the cost and availability of goods, will be confirmed by our manager by a phone call to the number you specified when ordering. (Prices are subject to change due to currency fluctuations.
Delivery
Our online store offers several delivery options:
- Express delivery;
- delivery of oversized cargo;
- store pickup.
Express delivery*
You can order the delivery of goods by courier, who will arrive at the specified address on any day convenient for you from 10.00 to 20.00. After the goods arrive at the warehouse Courier service will contact you and offer to choose a convenient delivery time. Specify the address.
Delivery by courier, within the Moscow Ring Road, the cost will be 390 rubles.
Targeted delivery by courier of small-sized equipment in the city of Moscow within two days at a time convenient for you (weighing no more than 5 kg, volume that can be delivered by courier "on hand").
*Check with the store manager if there is a courier service in your city.
Delivery of oversized cargo
Delivery of large and heavy equipment truck- 800 rubles. within the Moscow Ring Road. Outside it, an additional 30 rubles / km.
Pickup
You can pick up the item at one of our retail stores. Before receiving, wait for confirmation of information on the availability of goods in the store of your choice. The manager will tell you this information when confirming the order. Your friend or relative who knows the number and name to whom it is issued can pick up the purchase.
Addresses for pickup in Moscow and the region:
- "Expostroy on Nakhimovsky" (metro Profsoyuznaya), Nakhimovsky prospect, 24, building 1, No. 48, 3 pavilion, sector A No. 405, 3 pavilion, sector B
Mon-Sat: 10.00 - 20.00, Sun: 10.00 - 19.00.
Trade House "Million trifles" (m. Bibirevo) st. Prishvina, 26, 2nd floor, pavilion D27
Mon-Sun: 10.00 – 20.00.
G. Mytishchi, Volkovskoe highway, vl. 33 page 1
Mon-Fri: 09.00 - 18.00, Sat, Sun: day off.
