GOST 30493-96
INTERSTATE STANDARD
Types and basic dimensions
INTERSTATE SCIENTIFIC AND TECHNICAL COMMISSION
ON STANDARDIZATION, TECHNICAL REGULATION
AND CERTIFICATIONS IN CONSTRUCTION (MNTKS)
Foreword
1 DEVELOPED by the Research Institute of Building Ceramics (NIIstroykeramika)
INTRODUCED by the Ministry of Construction of Russia
2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (ISTCS) on December 11, 1996
voted to accept
State name | Body name government controlled construction |
The Republic of Azerbaijan | Gosstroy of the Republic of Azerbaijan |
Republic of Armenia | Ministry of Urban Development of the Republic of Armenia |
Republic of Belarus | Gosstroy of the Republic of Belarus |
The Republic of Kazakhstan | Ministry of Construction of the Republic of Kazakhstan |
Republic of Kyrgyzstan | Gosstroy of the Kyrgyz Republic |
The Republic of Moldova | Department of Architecture and Construction of the Republic of Moldova |
the Russian Federation | Gosstroy of Russia |
The Republic of Tajikistan | Gosstroy of the Republic of Tajikistan |
The Republic of Uzbekistan | Goskomarchitektstroy of the Republic of Uzbekistan |
3 INSTEAD OF GOST 75-82, GOST 21485.4-76, GOST 21485.5-76, GOST 22847-85, GOST 23759-85, GOST 26901-86
4 ENTERED INTO FORCE on January 1, 1998 as state standard Russian Federation Decree of the Gosstroy of Russia dated December 30, 1997 No. 18-76
INTERSTATE STANDARD
SANITARY CERAMIC PRODUCTS
Types and basic dimensions
CERAMIC SANITARY WARE
Types and principal dimensions
Introduction date 1998-01-01
1 area of use
This standard applies to sanitary ceramic (porcelain, semi-porcelain and faience) washbasins, washbasin pedestals, toilet bowls, flush cisterns, bidets, urinals and establishes their types and main dimensions.Ceramic sanitary products are intended for installation in sanitary facilities, in amenity and other premises of buildings for various purposes, in sanitary facilities of river and sea vessels and railway cars.
The requirements of section 3 are mandatory, the rest are recommended and can be specified by agreement between the manufacturer and the consumer (customer).
2 Normative references
In this standard, references are made to the following standards:GOST 13449-82 Sanitary ceramic products. Test Methods
GOST 15167-93 Sanitary ceramic products. General specifications
GOST 21485-94 Flush tanks and fittings for them. General specifications
3 Types and basic dimensions
3.1 Ceramic sanitary products (wash basins, toilet bowls, flush cisterns, bidets, urinals) are made the following types in accordance with the requirements of this standard according to approved working drawings.Elements of the main products are given in Appendix A.
3.2 The form of products is not regulated by this standard.
3.3 Washbasins
3.3.1 Types of washbasins
Washbasins are produced in the following types:
- semicircular, oval, rectangular, trapezoidal with or without a back;
- corner with or without a back and with or without overflow, with a cut corner;
- surgical and hairdressing without a back.
3.3.2 The main dimensions of semicircular, oval, rectangular and trapezoidal washbasins are given in Table 1 and Figure 1.
Table 1 In millimeters
Washbasin size | L | AT | H | l |
at least |
||||
1st | 400-500 | 300 | 135 | 180 |
2nd | 550 | 420 | ||
3rd | 600 | 450 | 150 | 180-200 |
4th | 650 | 500; 455* | ||
5th | 700 | 600 | ||
* Allowed for washbasins with built-in installation surfaces |
Figure 1 - Washbasin
![]() | A - A ![]() |
Figure 2 - Washbasin for railway cars
3.3.3 The main dimensions of corner, surgical and hairdressing wash basins are given in Table 2 and in Figures 2 and 3.
Table 2 In millimeters
Washbasin types | AT | L | H, not less | l | E |
Corner: backless | 495 | 625 | 185 | 310 | 430 |
with back | 470 | 608 | 130 | 253 | 430 |
with overflow | 492 | 625 | 166 | 310 | 430 |
cut corner | 390 | 544 | 166 | 190 | 205 |
Surgical | 590 | 650 | 190 | 180 | - |
hairdressing | 590 | 650 | 190 | 180 | - |
![]() | A-A ![]() |
* Hole D - only in the hairdresser's washbasin.
Figure 3 - Surgical and hairdressing washbasin
3.3.4 Semicircular, opal, rectangular and trapezoidal washbasins are made with or without holes in the shelves for installing mixing fittings, which must be indicated in the consumer's order.
The dimensions of the holes, their location and number, depending on the type of mixing fittings, must correspond to those indicated in Figure 5.
3.3.5 Corner and surgical washbasins are made without holes in the shelf. The dimensions of the hole in the shelf of the hairdresser's washbasin for the faucet are shown in Figure 3.
3.3.6 The dimensions of the hole in the bowl of the washbasin for installing the outlet must correspond to those indicated in Figure 6.
3.3.7 The configuration of the upper surface of the ceramic pedestal must correspond to the configuration of the lower surface of the bowl of the washbasin for which the pedestal is intended (Figure 4).
![](https://i0.wp.com/m.lawmix.ru/images/data/gosts/3824-7.png)
Figure 4 - Ceramic washbasin pedestal
for central mixer
![](https://i2.wp.com/m.lawmix.ru/images/data/gosts/3824-8.png)
For mixer with bottom mixing chamber
Figure 5 - Location and dimensions of holes in the shelves of washbasins for installing faucets
![](https://i0.wp.com/m.lawmix.ru/images/data/gosts/3824-10.png)
Figure 6 - Dimensions of the hole in the bowl of the washbasin for installing the outlet
3.4 Toilets
3.4.1 Types of toilets
Toilets produce the following types:
- plate-shaped with an oblique outlet with a one-piece molded shelf;
- plate-shaped with direct release with a one-piece molded shelf;
- plate-shaped with an oblique outlet without a one-piece molded shelf, including for children;
- plate-shaped with direct release without a one-piece molded shelf, including for children;
- visor with an oblique outlet with a one-piece molded shelf;
- visor with an oblique outlet without a one-piece molded shelf;
- funnel-shaped with direct release with a one-piece molded shelf;
- funnel-shaped with an oblique outlet with a one-piece molded shelf;
- funnel-shaped with direct release without a one-piece molded shelf;
- funnel-shaped with an oblique outlet without a one-piece molded shelf.
3.4.2 The main dimensions of the toilet bowls are shown in Table 3 and in Figures 7 and 8.
3.4.3 Toilets installed in the sanitary facilities of railway cars are shown in Figure 9.
3.4.4 For fixing toilet bowls must have holes:
- two or four, which should be indicated in the order - in toilet bowls installed in the sanitary facilities of amenity premises;
- three - in the toilet bowls installed in the sanitary facilities of railway cars.
At the request of the consumer, toilet bowls can be made without holes for fastening.
Table 3 In millimeters
Types of toilets | H | h | h1 | L | l | l1 | B | b |
With one-piece molded shelf | 370 and 400 | 320 and 350 | 150 | At least 605* | 330 | 435 | 340 and 360 | 260 |
Without molded shelf | 460 |
|||||||
Baby | 335 | 285 | 130 | 405 | 280 | 380 | 290 | 210 |
* By agreement between the consumer and the manufacturer, it is allowed to manufacture toilet bowls with a length of 575 mm. |
![](https://i0.wp.com/m.lawmix.ru/images/data/gosts/3824-11.png)
Figure 7 - Toilet bowl with one-piece molded shelf
![]() |
|
BUT ![]() | B |
Add-on shelf
![]() | ![]() |
Figure 8 - Toilet bowl with an attached shelf
Type Unzh1 | Type Unzh2 |
![]() | ![]() |
![]() | ![]() |
Figure 9 - Toilet bowls installed in the sanitary facilities of railway cars
3.5 Cisterns
3.5.1 Flushing tanks are available in the following types:
- flush mounted on the toilet with a side or top start;
- flush low, medium and high with side start.
3.5.2 Main dimensions flush tank must correspond to those indicated in Figure 10.
![]() |
|
A-A ![]() | ![]() |
![]() |
Figure 10 - High flush cistern with side start
By agreement between the consumer and the manufacturer, it is allowed to manufacture tanks of other sizes, mutually linked to connecting dimensions toilet bowls, filling and drain valve and providing consumer properties of the product.
3.5.3 Flushing tanks must comply with the requirements of GOST 21485.
3.5.4 Holes in tanks, for drain fittings and fastening to toilet bowls are accepted according to working drawings.
3.6 Bidet
3.6.1 Types of bidets
Bidets are available in the following types:
1 - without overflow;
2 - with overflow.
3.6.2 The main dimensions of the bidet are shown in Table 4 and Figure 11.
![](https://i0.wp.com/m.lawmix.ru/images/data/gosts/3824-25.png)
![](https://i0.wp.com/m.lawmix.ru/images/data/gosts/3824-26.png)
Figure 11 - Bidet
Table 4 In millimeters
Bidet types | L | l | AT | H | h |
1 | 640 | 180 | 360 | 380 | 200 |
2 | 600 | 180 | 350 | 398 | 200 |
3.6.3 The dimensions of the openings, their location and number, depending on the type of mixing fittings and outlet, must correspond to those indicated in Figure 12.
The location and dimensions of the holes in the bidet shelf for installing water fittings
Version 1
![](https://i0.wp.com/m.lawmix.ru/images/data/gosts/3824-27.png)
Execution 2 (at the request of the consumer)
![](https://i2.wp.com/m.lawmix.ru/images/data/gosts/3824-28.png)
Dimensions of hole in bidet bowl for outlet installation
* It is allowed to produce with one hole.
Figure 12 - The location and dimensions of the openings in the bidet for installing the outlet
By agreement with the consumer, it is allowed to manufacture a bidet with one hole in the shelf for installing water fittings.
3.7 Urinals
3.7.1 Types of urinals
Urinals are available in the following types:
- wall-mounted with one-piece cast siphon type 1;
- wall-mounted with one-piece cast siphon type 2;
- wall-mounted without a one-piece ceramic siphon.
3.7.2 The main dimensions of urinals should be as shown in Figure 13.
![]() | ![]() |
Figure 13 - Urinal
3.8 Limit deviations overall dimensions and other sizes over 50 mm should be +2.5 to -3%. Dimensional deviations of 50 mm or less, with the exception of those indicated in Figures 5 and 12, must be established in the working drawings.
3.9 The symbolic designation of products should consist of the first one or two letters of the product, the type designation (1, 2, 3 or 4), the number indicating the size of the washbasin, the letters: D - for children's toilets, C - for washbasins with a back, bS - for washbasins without a back, p - for washbasins with overflow, SU - for washbasins with a cut corner, vp - for cisterns with a top start, bp - for cisterns with a side start, F - for porcelain items, pf - for semi-porcelain items, fs - for faience products and the designation of this standard.
Example symbol washbasin rectangular, third size, with backrest, porcelain:
UmPrZSF GOST 30493-96
The same, a corner washbasin, with a cut corner, semi-porcelain:
UmUgSupf GOST 30493-96
The same, a bowl-shaped toilet bowl, with a direct outlet, without a one-piece cast shelf, porcelain:
UNTPF GOST 30493-96
The same, a toilet bowl for children, with an oblique outlet, porcelain:
UNTDF GOST 30493-96
The same, a low-lying flushing cistern, with a top start, made of porcelain:
BNvpF GOST 30493-96
The same, urinal with one-piece siphon type 1, porcelain:
PS1F GOST 30493-96
The same, a urinal without a one-piece semi-porcelain ceramic siphon:
Ppf GOST 30493-96
3.10 Grading is set according to indicators appearance according to GOST 15167.
The attached shelf is not subject to subdivision into varieties.
3.11 Technical requirements, acceptance rules, marking, packaging, transportation, storage and manufacturer's warranties - in accordance with GOST 15167.
Test methods - according to GOST 13449.
4 Installation instructions
The toilet is installed in a specially prepared place: the pedestal is fixed with two or four bolts or screws, depending on the design of the toilet on wooden platform or fix cement mortar.On a toilet with a one-piece molded shelf, the tank is bolted to the toilet shelf.
When installing a tank mounted on a separate shelf rubber cuff, located on the nozzle of the shelf, is put on the socket of the toilet bowl and after that the shelf is attached to the toilet bowl.
The float valve must completely shut off the flow of water into the tank when the level is 20 mm below the overflow.
Installing a washbasin on metal brackets
On a pre-marked wall, two brackets are installed (with screws, bolts or by shooting) at a distance corresponding to the size between the mounting holes of the washbasin.
The washbasin is mounted on brackets and its tailgate is fixed with a bracket or in another way, providing a load on the front edge of at least 1.5 kN (150 kgf) from tipping over.
Installing a washbasin on a pedestal with bolts
On the pre-marked wall, two bolts are installed at a distance corresponding to the size between the mounting holes on the rear mounting surface of the washbasin.
The washbasin is mounted on a pedestal and bolted to the wall.
The fastening must provide a load on the front edge of the washbasin of at least 1.5 kN (150 kgf) from overturning.
APPENDIX A
(reference)Elements of the main products
Table A1Element name | Item number in figure A1 |
Front board | 1 |
Back wall | 2 |
Reinforcing panel | 3 |
Recess for soap (soap dishes) | 4 |
Bowl | 5 |
The outer wall of the product | 6 |
Drain hole (inside) | 7 |
Drain hole (outside) | 8 |
overflow channel | 9 |
Overflow hole (overflow) | 10 |
reference rib | 11 |
Mounting holes | 12 |
Rebar holes | 13 |
Rinsing water inlet | 14 |
Flushing wreath (ring) | 15 |
Water distributor | 16 |
Plate | 17 |
Channel | 18 |
Outlet | 19 |
Outlet fitting | 20 |
pedestal | 21 |
22 |
|
water lock | 23 |
tank cover | 24 |
flush tank
![]() | |
![]() |
Toilet bowl
![](https://i1.wp.com/m.lawmix.ru/images/data/gosts/3824-35.png)
Bidet
![](https://i1.wp.com/m.lawmix.ru/images/data/gosts/3824-36.png)
Urinal
![]() | ![]() |
Figure A1, sheet 1
Wash basin
![]() | ![]() |
Sink (sink)
![](https://i2.wp.com/m.lawmix.ru/images/data/gosts/3824-41.png)
Bath
![]() | ![]() |
![]() |
Figure A1, sheet 2
Key words: sanitary ceramic products, toilets, washbasins, cisterns, bidets, urinals
CONTENT
GOST 30494-96 interstate standard residential and public buildings. indoor microclimate parameters Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (ISTC) »
GOST 30493-96
UDC 696.14.012.8.006:354 Group G21
INTERSTATE STANDARD
SANITARY CERAMIC PRODUCTS
Types and basic dimensions
Ceramic sanitary ware.
Types and principal dimensions
ISS 91.140.70
Introduction date 1998-07-01
Foreword
1 DEVELOPED by the Research Institute of Building Ceramics (NIIstroykeramika)
INTRODUCED by the Ministry of Construction of Russia
2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (ISTCS) on December 11, 1996
State name | Name of the public administration body for construction |
The Republic of Azerbaijan | Gosstroy of the Republic of Azerbaijan |
Republic of Armenia | Ministry of Urban Development of the Republic of Armenia |
Republic of Belarus | Gosstroy of the Republic of Belarus |
The Republic of Kazakhstan | Ministry of Construction of the Republic of Kazakhstan |
Kyrgyz Republic | Gosstroy of the Kyrgyz Republic |
The Republic of Moldova | Department of Architecture and Construction of the Republic of Moldova |
the Russian Federation | Ministry of Construction of Russia |
The Republic of Tajikistan | Gosstroy of the Republic of Tajikistan |
The Republic of Uzbekistan | Goskomarchitektstroy of the Republic of Uzbekistan |
3. INSTEAD OF GOST 755-82, GOST 21485.4-76, GOST 21485.5-76, GOST 22847-85, GOST 23759-85, GOST 26901-86, ST SEV 1002-78
4. By Decree of the Ministry of Construction of Russia dated December 30, 1997 No. 18-76, the interstate standard GOST 30493-96 was put into effect directly as the state standard of the Russian Federation from January 1, 1998.
1 area of use
This standard applies to sanitary ceramic (porcelain, semi-porcelain and faience) washbasins, washbasin pedestals, toilet bowls, flush cisterns, bidets, urinals and establishes their types and main dimensions.
Ceramic sanitary products are intended for installation in sanitary facilities, in amenity and other premises of buildings for various purposes, in sanitary facilities of river and sea vessels and railway cars.
The requirements of section 3 are mandatory, the rest are recommended, and can be specified by agreement between the manufacturer and the consumer (customer).
GOST 13449-82 Sanitary ceramic products. Test Methods
GOST 15167-93 Sanitary ceramic products. General specifications
GOST 21485-94 Flush tanks and fittings for them. General specifications
3 Types and basic dimensions
3.1 Ceramic sanitary products (wash basins, toilet bowls, flush tanks, bidets, urinals) are made of the following types in accordance with the requirements of this standard according to approved working drawings.
Elements of the main products are given in Appendix A.
3.2 The form of products is not regulated by this standard.
3.3 Washbasins
3.3.1 Types of washbasins
Washbasins are produced in the following types:
Semicircular, oval, rectangular, trapezoidal with or without a back;
Corner with or without a back and with or without overflow, with a cut corner;
Surgical and hairdressing without a back.
3.3.2 The main dimensions of semicircular, oval, rectangular and trapezoidal washbasins are shown in Figure 1 and Table 1.
GOST 30493 96 is a generally accepted interstate standard for sanitary ceramic products: types and main dimensions.
- Scope of GOST 30493-96
- Normative references
- Types and main dimensions of sanitary ceramic products:
- Urinals GOST 30493-96
- Annex A
- Installation instructions
GOST 30493-96. Sanitary ceramic products. Types and basic dimensions
GOST 30493-96
Group G21
INTERSTATE STANDARD
SANITARY CERAMIC PRODUCTS
Types and basic dimensions
Ceramic sanitary ware.
Types and principal dimensions
Introduction date 1998-07-01
Foreword
1 GOST 30493 96 developed by the Research Institute of Building Ceramics (NIIstroykeramika)
Introduced by the Ministry of Construction of Russia
2 Adopted by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (MNTKS) on December 11, 1996
Name of the state that adopted GOST 30493-96 |
Name of the public administration body for construction |
---|---|
The Republic of Azerbaijan |
Gosstroy of the Republic of Azerbaijan |
Republic of Armenia |
Ministry of Urban Development of the Republic of Armenia |
Republic of Belarus |
Gosstroy of the Republic of Belarus |
The Republic of Kazakhstan |
Ministry of Construction of the Republic of Kazakhstan |
Kyrgyz Republic |
Gosstroy of the Kyrgyz Republic |
The Republic of Moldova |
Department of Architecture and Construction of the Republic of Moldova |
the Russian Federation |
Ministry of Construction of Russia |
The Republic of Tajikistan |
Gosstroy of the Republic of Tajikistan |
The Republic of Uzbekistan |
Goskomarchitektstroy of the Republic of Uzbekistan |
- INSTEAD OF GOST 755-82, GOST 21485.4-76, GOST 21485.5-76, GOST 22847-85, GOST 23759-85, GOST 26901-86, ST SEV 1002-78
- By Decree of the Ministry of Construction of Russia of December 30, 1997 N 18-76, the interstate standard GOST 30493-96 was put into effect directly as a state standard of the Russian Federation from July 1, 1998.
Amended by database manufacturer
1. Scope of GOST 30493-96
This standard applies to sanitary ceramic (porcelain, semi-porcelain and faience) washbasins, washbasin pedestals, toilet bowls, flush cisterns, bidets, urinals and establishes their types and main dimensions.
Ceramic sanitary products are intended for installation in sanitary facilities, in amenity and other premises of buildings for various purposes, in sanitary facilities of river and sea vessels and railway cars.
The requirements of section 3 are mandatory, the rest are recommended, and can be specified by agreement between the manufacturer and the consumer (customer).
2. Regulatory references
GOST 13449-82 Sanitary ceramic products. Test Methods
GOST 15167-93 Sanitary ceramic products. General specifications
GOST 21485-94 Flush tanks and fittings for them. General specifications
3. Types and main dimensions
3.1 Ceramic sanitary products (wash basins, toilet bowls, flush tanks, bidets, urinals) are made of the following types in accordance with the requirements of this standard according to approved working drawings.
Elements of the main products are given in Appendix A.
3.2 The form of products is not regulated by this standard.
3.3 Washbasins
3.3.1 Types of washbasins
Washbasins are produced in the following types:
- semicircular, oval, rectangular, trapezoidal with or without a back;
- corner with or without backrest and with or without overflow, with a cut corner;
- surgical and hairdressing without a back.
3.3.2 The main dimensions of semicircular, oval, rectangular and trapezoidal washbasins are shown in Figure 1.
3.3.3 The main dimensions of corner, surgical and hairdressing washbasins are given in Table 2 and in Figures 2, 3.
3.3.4 Semicircular, oval, rectangular and trapezoidal washbasins are made with or without holes in the shelves for installing mixing fittings, which must be indicated in the consumer's order.
The dimensions of the holes, their location and number, depending on the type of mixing fittings, must correspond to those indicated in Figure 5.
3.3.5 Corner and surgical washbasins are made without holes in the shelf. The dimensions of the hole in the shelf of the hairdresser's washbasin for the faucet are shown in Figure 3.
3.3.6 The dimensions of the hole in the bowl of the washbasin for installing the outlet must correspond to those indicated in Figure 6.
3.3.7 Configuration upper surface ceramic pedestal must correspond to the configuration of the bottom surface of the washbasin bowl, for which the pedestal is intended (picture 4).
3.4 Toilets
3.4.1 Types of toilets
Toilets produce the following types:
- a bowl-type toilet bowl with an oblique outlet with a one-piece molded shelf;
— bowl bowl with direct release with integrally molded shelf;
- a bowl-shaped toilet bowl with an oblique outlet without a one-piece cast shelf, including for children;
- a bowl-type toilet bowl with a direct outlet without a one-piece molded shelf, including for children;
- a visor toilet bowl with an oblique outlet with a one-piece molded shelf;
- a visor toilet bowl with an oblique outlet without a one-piece molded shelf;
- a funnel-shaped toilet bowl with a direct outlet with a one-piece molded shelf;
- a funnel-shaped toilet bowl with an oblique outlet with a one-piece molded shelf;
- a funnel-shaped toilet bowl with a direct outlet without a one-piece molded shelf;
- a funnel-shaped toilet bowl with an oblique outlet without a one-piece molded shelf.
3.4.2 The main dimensions of the toilets are shown in Figures 7, 8 and Table 3.
Figure 7 - Toilet bowl with one-piece molded shelf
Figure 8 - Toilet bowl with an attached shelf
Table 3
In millimeters
Types of toilets |
H | h | h1 | l | l1 | L | b | B |
With one-piece molded shelf |
At least 605* |
|||||||
Without molded shelf |
||||||||
____________________ * It is allowed, upon agreement between the consumer and the manufacturer, to produce toilet bowls with a length of 575 mm. |
3.4.3 Toilets installed in the sanitary facilities of railway cars are shown in Figure 9.
3.4.4 For fixing toilet bowls must have holes:
- in toilet bowls installed in sanitary facilities of household premises - two or four holes, which must be indicated in the order;
- in toilet bowls installed in the sanitary units of railway cars - three holes.
At the request of the consumer, toilet bowls are allowed to be manufactured without holes for fastening.
3.5 Cisterns
3.5.1 Types of cistern
Flushing tanks are available in the following types:
- a flushing cistern mounted on a toilet bowl with a side or top start;
- flushing tank low, medium and high with side start.
3.5.2 The main dimensions of the flushing tank should correspond to those shown in Figure 10.
It is allowed, upon agreement between the consumer and the manufacturer, to manufacture cisterns of other sizes, interconnected with the connecting dimensions of the toilet bowls, filling and drain fittings and ensuring the consumer properties of the product.
3.5.3 Flushing tanks must comply with the requirements of GOST 21485.
3.5.4 Holes in tanks for flush fittings and attachments to toilet bowls are accepted according to working drawings.
3.6.1 Types of bidets
Bidets are available in the following types:
1 - without overflow; 2 - with overflow.
It is allowed, in agreement with the consumer, to produce a type 2 bidet without overflow.
3.6.2 The main dimensions of the bidet are shown in Figure 11 and Table 4.
Figure 11 - Bidet
Table 4 (mm)
L | l | B | H | h | |
3.6.3 The dimensions of the openings, their location and number, depending on the type of mixing fittings and outlet, must correspond to those indicated in Figure 12.
By agreement with the consumer, it is allowed to manufacture a bidet with one hole in the shelf for installing water fittings.
Urinals GOST 30493-96
3.7 Urinals
3.7.1 Types of urinals
Urinals are available in the following types:
— wall-mounted urinal with one-piece cast siphon type 1;
— wall-mounted urinal with one-piece cast siphon type 2;
— a wall-mounted urinal without a one-piece cast ceramic siphon.
3.7.2 The main dimensions of urinals should be as shown in Figure 13.
Figure 13 - Urinal
Symbols for sanitary ceramic products
3.8 Limit deviations of overall dimensions and other dimensions of more than 50 mm should be from plus 2.5 to minus 3%. Dimensional deviations of 50 mm or less, with the exception of those indicated in Figures 5 and 12, must be established in the working drawings.
3.9 The symbolic designation of products should consist of the first one or two letters of the product, a type designation (1, 2, 3 or 4), a number indicating the design of the toilet flush ring or the size of the washbasin, letters: D - for children's toilets, C - for washbasins with back, bS - for washbasins without a back, p - for washbasins with overflow, SU - for washbasins with a cut corner, vp - for cisterns with a top start, bp - for cisterns with a side start, f - for porcelain, pf - for semi-porcelain products, fs - for faience products and the designation of this standard.
An example of a symbol for a rectangular washbasin, third size, with a backrest, porcelain:
UmPr3SF GOST 30493-96
The same, a corner washbasin, with a cut corner, semi-porcelain:
UmUgSupf GOST 30493-96
The same, bowl-shaped toilet bowl, with direct outlet, without one-piece molded shelf, with flush ring, version 2, porcelain:
UnTP2f GOST 30493-96
The same, toilet bowl for children, with an oblique outlet, with a flush ring, version 1, porcelain:
UnT1Df GOST 30493-96
The same, a low-lying flushing cistern, with a top start, made of porcelain:
BNvpf GOST 30493-96
The same, urinal with one-piece siphon type 1, porcelain:
PS1f GOST 30493-96
Urinal without one-piece cast ceramic semi-porcelain siphon:
Ppf GOST 30493-96
3.10 The grade is determined according to the appearance indicators in accordance with GOST 15167.
The attached shelf is not subject to subdivision into varieties.
3.11 Technical requirements, acceptance rules, marking, packaging, transportation, storage and manufacturer's guarantees - in accordance with GOST 15167. Test methods - in accordance with GOST 13449.
Installation instructions
The toilet bowl is installed in a specially prepared place: the pedestal is fixed with two or four bolts or screws, depending on the design of the toilet bowl, on a wooden platform or fixed with cement mortar. On a toilet with a one-piece molded shelf, the tank is bolted to the toilet shelf. When installing a tank mounted on a separate shelf, the rubber cuff located on the nozzle of the shelf is put on the socket of the toilet bowl and after that the shelf is attached to the toilet bowl.
The float valve must completely shut off the flow of water into the tank when the level is 20 mm below the overflow.
Installation of a washbasin on metal brackets.
On a pre-marked wall, two brackets are installed (with screws, bolts or by shooting) at a distance corresponding to the size between the mounting holes of the washbasin. The washbasin is mounted on brackets and its tailgate is fixed with a bracket or in another way, providing a load on the front edge of at least 1.5 kN (150 kgf) from overturning.
Installation of a washbasin on a pedestal with bolts.
On the pre-marked wall, two bolts are installed at a distance corresponding to the size between the mounting holes on the rear mounting surface of the washbasin. The washbasin is mounted on a pedestal and bolted to the wall. The fastening must provide a load on the front edge of the washbasin of at least 1.5 kN (150 kgf) from overturning.
GOST 30493-96 Appendix A
Table A.1
Element name |
Item number in Figure A.1 |
Front board |
|
Back wall |
|
Reinforcing panel |
|
Recess for soap (soap dishes) |
|
The outer wall of the product |
|
Drain hole (inside) |
|
Drain hole (outside) |
|
overflow channel |
|
Overflow hole (overflow) |
|
reference rib |
|
Mounting holes |
|
Rebar holes |
|
Rinsing water inlet |
|
Flushing wreath (ring) |
|
Water distributor |
|
Outlet |
|
Outlet fitting |
|
pedestal |
|
water lock |
|
tank cover |
The text of the document is verified by:
official publication
MNTKS - M .: IPK Publishing House
standards, 1998
(Visited 111 times, 1 visits today)
SANITARY CERAMIC PRODUCTS
Types and basic dimensions
Ceramic sanitary ware.
Types and principal dimensions
ISS 91.140.70
OKSTU 4960
Introduction date 1998-07-01
Foreword
1 DEVELOPED by the Research Institute of Building Ceramics (NIIstroykeramika)
INTRODUCED by the Ministry of Construction of Russia
2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (ISTCS) on December 11, 1996
State name |
Name of the public administration body for construction |
The Republic of Azerbaijan |
Gosstroy of the Republic of Azerbaijan |
Republic of Armenia |
Ministry of Urban Development of the Republic of Armenia |
Republic of Belarus |
Gosstroy of the Republic of Belarus |
The Republic of Kazakhstan |
Ministry of Construction of the Republic of Kazakhstan |
Kyrgyz Republic |
Gosstroy of the Kyrgyz Republic |
The Republic of Moldova |
Department of Architecture and Construction of the Republic of Moldova |
the Russian Federation |
Ministry of Construction of Russia |
The Republic of Tajikistan |
Gosstroy of the Republic of Tajikistan |
The Republic of Uzbekistan |
Goskomarchitektstroy of the Republic of Uzbekistan |
3. INSTEAD OF GOST 755-82, GOST 21485.4-76, GOST 21485.5-76, GOST 22847-85, GOST 23759-85, GOST 26901-86, ST SEV 1002-78
4. By Decree of the Ministry of Construction of Russia dated December 30, 1997 No. 18-76, the interstate standard GOST 30493-96 was put into effect directly as the state standard of the Russian Federation from January 1, 1998.
1 area of use
This standard applies to sanitary ceramic (porcelain, semi-porcelain and faience) washbasins, washbasin pedestals, toilet bowls, flush cisterns, bidets, urinals and establishes their types and main dimensions.
Ceramic sanitary products are intended for installation in sanitary facilities, in amenity and other premises of buildings for various purposes, in sanitary facilities of river and sea vessels and railway cars.
The requirements of section 3 are mandatory, the rest are recommended, and can be specified by agreement between the manufacturer and the consumer (customer).
This standard uses references to the following standards:
GOST 13449-82 Sanitary ceramic products. Test Methods
GOST 15167-93 Sanitary ceramic products. General specifications
GOST 21485-94 Flush tanks and fittings for them. General specifications
3 Types and basic dimensions
3.1 Ceramic sanitary products (wash basins, toilet bowls, flush tanks, bidets, urinals) are made of the following types in accordance with the requirements of this standard according to approved working drawings.
Elements of the main products are given in Appendix A.
3.2 The form of products is not regulated by this standard.
3.3
3.3.1 Types of washbasins
Washbasins are produced in the following types:
Semicircular, oval, rectangular, trapezoidal with or without a back;
Corner with or without a back and with or without overflow, with a cut corner;
Surgical and hairdressing without a back.
3.3.2 The main dimensions of semicircular, oval, rectangular and trapezoidal washbasins are shown in Figure 1 and Table 1.
Figure 1 - Washbasin
Table 1
In millimeters
Great- rank |
||||
washed- Nika |
at least |
|||
1st |
400-500 |
|||
2nd |
||||
3rd |
180-200 |
|||
4th |
500, 455* |
|||
5th |
||||
__________________ * Allowed for washbasins with built-in installation surfaces. |
3.3.3 The main dimensions of corner, surgical and hairdressing washbasins are given in Table 2 and in Figures 2, 3.
table 2
In millimeters
Types of washbasins |
Not less than |
||||
Corner without back |
|||||
Corner with back |
|||||
Corner with overflow |
|||||
Corner with cut corner |
|||||
Surgical |
|||||
hairdressing |
Figure 2 - Washbasin for railway cars
____________________
* Hole D - only in the hairdresser's washbasin.
Figure 3 - Surgical and hairdressing washbasin
3.3.4 Semicircular, oval, rectangular and trapezoidal washbasins are made with or without holes in the shelves for installing mixing fittings, which must be indicated in the consumer's order.
The dimensions of the holes, their location and number, depending on the type of mixing fittings, must correspond to those indicated in Figure 5.
Figure 4 - Ceramic washbasin pedestal
3.3.5 Corner and surgical washbasins are made without holes in the shelf. The dimensions of the hole in the shelf of the hairdresser's washbasin for the faucet are shown in Figure 3.
3.3.6 The dimensions of the hole in the bowl of the washbasin for installing the outlet must correspond to those indicated in Figure 6.
Figure 6 - Dimensions of the hole in the bowl of the washbasin
to install release
3.3.7 The configuration of the upper surface of the ceramic pedestal must correspond to the configuration of the lower surface of the bowl of the washbasin for which the pedestal is intended (Figure 4).
3.4 Toilet bowls
3.4.1 Types of toilets
Toilets produce the following types:
A bowl-shaped toilet bowl with an oblique outlet with a one-piece molded shelf;
Direct outlet bowl WC with one-piece molded shelf;
A bowl-shaped toilet bowl with an oblique outlet without a one-piece molded shelf, including for children;
A bowl-type toilet bowl with a direct outlet without a one-piece molded shelf, including for children;
A visor toilet bowl with an oblique outlet with a one-piece molded shelf;
A visor toilet bowl with an oblique outlet without a one-piece molded shelf;
A funnel-shaped toilet bowl with a direct outlet with a one-piece molded shelf;
A funnel-shaped toilet bowl with an oblique outlet with a one-piece molded shelf;
A funnel-shaped toilet bowl with a direct outlet without a one-piece molded shelf;
The toilet bowl is funnel-shaped with an oblique outlet without a one-piece molded shelf.
3.4.2 The main dimensions of the toilets are shown in Figures 7, 8 and Table 3.
Figure 7 - Toilet bowl with one-piece molded shelf
Add-on shelf
Figure 8 - Toilet bowl with an attached shelf
Table 3
In millimeters
Types of toilets |
||||||||
With one-piece molded shelf |
At least 605* |
340 and 360 |
||||||
Without molded shelf |
370 and 400 |
320 and 350 |
||||||
Baby |
||||||||
____________________ * It is allowed, upon agreement between the consumer and the manufacturer, to produce toilet bowls with a length of 575 mm. |
3.4.3 Toilets installed in the sanitary facilities of railway cars are shown in Figure 9.
3.4.4 For fixing toilet bowls must have holes:
In toilet bowls installed in the sanitary facilities of amenity premises, there are two or four holes, which must be indicated in the order;
There are three holes in the toilet bowls installed in the sanitary units of railway cars.
At the request of the consumer, toilet bowls are allowed to be manufactured without holes for fastening.
3.5 flush cisterns
3.5.1 Types of cistern
Flushing tanks are available in the following types:
Flushing cistern mounted on the toilet with side or top start;
Flushing cistern low, medium and high with side start.
3.5.2 The main dimensions of the flushing tank should correspond to those shown in Figure 10.
It is allowed, upon agreement between the consumer and the manufacturer, to manufacture cisterns of other sizes, interconnected with the connecting dimensions of the toilet bowls, filling and drain fittings and ensuring the consumer properties of the product.
3.5.3 Flushing tanks must comply with the requirements of GOST 21485.
3.5.4 Holes in tanks for flush fittings and attachments to toilet bowls are accepted according to working drawings.
Figure 10 - High flush cistern
with side launch
3.6
3.6.1 Types of bidets
Bidets are available in the following types:
1 - without overflow; 2 - with overflow.
It is allowed, in agreement with the consumer, to produce a type 2 bidet without overflow.
3.6.2 The main dimensions of the bidet are shown in Figure 11 and Table 4.
Figure 11 - Bidet
Table 4
In millimeters
Bidet type |
|||||
3.6.3 The dimensions of the openings, their location and number, depending on the type of mixing fittings and outlet, must correspond to those indicated in Figure 12.
By agreement with the consumer, it is allowed to manufacture a bidet with one hole in the shelf for installing water fittings.
The location and dimensions of the holes in the bidet shelf for installing water fittingsVERSION 1
VERSION 1
(at the request of the consumer)
Dimensions of hole in bidet bowl for outlet installation
____________________
* It is allowed to produce with one hole
Figure 12 - Location and dimensions of holes in the bidet
3.7.1 Types of urinals
Urinals are available in the following types:
Wall-mounted urinal with one-piece cast siphon type 1;
Wall-mounted urinal with one-piece cast siphon type 2;
Wall-mounted urinal without a one-piece ceramic siphon.
3.7.2 The main dimensions of urinals should be as shown in Figure 13.
Figure 13 - Urinal
3.8 Limit deviations of overall dimensions and other dimensions of more than 50 mm should be from plus 2.5 to minus 3%. Dimensional deviations of 50 mm or less, with the exception of those indicated in Figures 5 and 12, must be established in the working drawings.
3.9 The symbolic designation of products should consist of the first one or two letters of the product, a type designation (1, 2, 3 or 4), a number indicating the design of the toilet flush ring or the size of the washbasin, letters: D - for children's toilets, C - for washbasins with back, bS - for washbasins without a back, p - for washbasins with overflow, SU - for washbasins with a cut corner, vp - for cisterns with a top start, bp - for cisterns with a side start, f - for porcelain, pf - for semi-porcelain products, fs - for faience products and the designation of this standard.
An example of a symbol for a rectangular washbasin, third size, with a backrest, porcelain:
UmPr3SF GOST 30493-96
The same, a corner washbasin, with a cut corner, semi-porcelain:
UmUgSupf GOST 30493-96
The same, bowl-shaped toilet bowl, with direct outlet, without one-piece molded shelf, with flush ring, version 2, porcelain:
UnTP2f GOST 30493-96
The same, toilet bowl for children, with an oblique outlet, with a flush ring, version 1, porcelain:
UnT1Df GOST 30493-96
The same, a low-lying flushing cistern, with a top start, made of porcelain:
BNvpf GOST 30493-96
The same, urinal with one-piece siphon type 1, porcelain:
PS1f GOST 30493-96
Urinal without one-piece cast ceramic semi-porcelain siphon:
Ppf GOST 30493-96
3.10 The grade is determined according to the appearance indicators in accordance with GOST 15167.
The attached shelf is not subject to subdivision into varieties.
3.11 Technical requirements, acceptance rules, marking, packaging, transportation, storage and manufacturer's guarantees - in accordance with GOST 15167. Test methods - in accordance with GOST 13449.
4 Installation instructions
The toilet bowl is installed in a specially prepared place: the pedestal is fixed with two or four bolts or screws, depending on the design of the toilet bowl, on a wooden platform or fixed with cement mortar. On a toilet with a one-piece molded shelf, the tank is bolted to the toilet shelf. When installing a tank mounted on a separate shelf, the rubber cuff located on the nozzle of the shelf is put on the socket of the toilet bowl and after that the shelf is attached to the toilet bowl.
The float valve must completely shut off the flow of water into the tank when the level is 20 mm below the overflow.
Installation of a washbasin on metal brackets.
On a pre-marked wall, two brackets are installed (with screws, bolts or by shooting) at a distance corresponding to the size between the mounting holes of the washbasin. The washbasin is mounted on brackets and its tailgate is fixed with a bracket or in another way, providing a load on the front edge of at least 1.5 kN (150 kgf) from overturning.
Installation of a washbasin on a pedestal with bolts.
On the pre-marked wall, two bolts are installed at a distance corresponding to the size between the mounting holes on the rear mounting surface of the washbasin. The washbasin is mounted on a pedestal and bolted to the wall. The fastening must provide a load on the front edge of the washbasin of at least 1.5 kN (150 kgf) from overturning.
Annex A
(reference)
Elements of the main products
Table A.1
Element name |
Element name |
Item number in Figure A.1 |
|
Front board |
Rebar hole |
||
Back wall |
Rinsing water inlet |
||
Reinforcing panel |
Flushing wreath (ring) |
||
Recess for soap (soap dishes) |
Water distributor |
||
Bowl |
Plate |
GOST 26901-86
1 area of use
This standard applies to sanitary ceramic (porcelain, semi-porcelain and faience) washbasins, washbasin pedestals, toilet bowls, flush cisterns, bidets, urinals and establishes their types and main dimensions.
Ceramic sanitary products are intended for installation in sanitary facilities, in amenity and other premises of buildings for various purposes, in sanitary facilities of river and sea vessels and railway cars.
3.2. The form of products is not regulated by this standard.
3.3. Washbasins
3.3.1. Washbasin types
Washbasins are produced in the following types:
Semicircular, oval, rectangular, trapezoidal with or without a back;
Corner with or without a back and with or without overflow, with a cut corner;
Surgical and hairdressing without a back.
3.3.2. The main dimensions of semicircular, oval, rectangular and trapezoidal washbasins are shown in Table 1 and Figure 1.
Table 1
In millimeters
Value washbasin |
L | AT | H | l |
at least | ||||
1st 2nd 3rd 4th 5th |
400-500 550 600 650 700 |
300 420 450 500; 455 600 |
135 | 180 |
* Allowed for washbasins with built-in installation surfaces |
3.3.3. The main dimensions of corner, surgical and hairdressing washbasins are given in table 2 and in figures 2 and.
table 2
In millimeters
3.3.4. Semicircular, oval, rectangular and trapezoidal washbasins are made with or without holes in the shelves for the installation of mixing fittings, which must be indicated in the consumer's order.
The dimensions of the holes, their location and number, depending on the type of mixing fittings, must correspond to those indicated in Figure 5.
3.3.5. Corner and surgical washbasins are made without holes in the shelf. The dimensions of the hole in the shelf of the hairdresser's washbasin for the mixer are shown in Figure 3.
3.3.6. The dimensions of the hole in the bowl of the washbasin for installing the outlet must correspond to those indicated in Figure 6.
3.3.7. The configuration of the upper surface of the ceramic pedestal must correspond to the configuration of the lower surface of the bowl of the washbasin for which the pedestal is intended (Figure 4).
3.4. Toilet bowls
3.4.1. Types of toilets
Toilets produce the following types:
Plate-shaped with an oblique outlet with a one-piece molded shelf;
Poppet with direct release with one-piece molded shelf;
Plate-shaped with an oblique outlet without a one-piece molded shelf, including for children;
Dish-shaped with direct release without a one-piece molded shelf, including for children;
Visor with an oblique outlet with a one-piece molded shelf;
Visor with an oblique outlet without a one-piece molded shelf;
Funnel-shaped with a direct outlet with a one-piece molded shelf;
Funnel-shaped with an oblique outlet with a one-piece molded shelf;
Funnel-shaped with direct release without a one-piece molded shelf;
Funnel-shaped with an oblique outlet without a one-piece molded shelf.
3.4.4. For fixing toilets must have holes:
Two or four, which must be indicated in the order - in toilet bowls installed in sanitary facilities of amenity premises;
Three - in the toilets installed in the sanitary facilities of railway cars.
At the request of the consumer, toilet bowls can be made without holes for fastening.
Table 3
In millimeters
Types of toilets | H | h | h_1 | L | l | l_1 | AT | b |
With one-piece cast shelf |
Not less than 605 |
|||||||
Without one-piece cast shelves |
460 | 330 | 435 | |||||
Baby | 335 | 285 | 130 | 405 | 280 | 380 | 290 | 210 |
* By agreement between the consumer and the manufacturer, it is allowed to manufacture toilet bowls 575 mm long. |
3.5. flush cisterns
3.5.1. Flushing tanks are available in the following types:
Flush mounted on the toilet with a side or top start;
Flush low, medium and high with side start.
3.5.2. The main dimensions of the flush tank must correspond to those indicated in Figure 10.
By agreement between the consumer and the manufacturer, it is allowed to manufacture cisterns of other sizes, mutually linked to the connecting dimensions of the toilet bowls, filling and drain fittings and ensuring the consumer properties of the product.
3.5.4. Holes in tanks for drain fittings and attachments to toilet bowls are accepted according to working drawings.
3.6.1. Bidet types
Bidets are available in the following types:
1 - without overflow;
2 - with overflow.
3.6.2. The main dimensions of the bidet are shown in table 4 and in figure 11.
Table 4
In millimeters
Bidet types | L | l | AT | H | h |
1 2 |
640 600 |
180 180 |
360 350 |
380 398 |
200 200 |
3.6.3. The dimensions of the holes, their location and number, depending on the type of mixing fittings and outlet, must correspond to those indicated in Figure 12.
By agreement with the consumer, it is allowed to manufacture a bidet with one hole in the shelf for installing water fittings.
3.7. urinals
3.7.1. Types of urinals
Urinals are available in the following types:
Wall-mounted with one-piece cast siphon type 1;
Wall-mounted with one-piece cast siphon type 2;
Wall-mounted without a one-piece cast ceramic siphon.
3.8. Limit deviations of overall dimensions and other dimensions of more than 50 mm should be from +2.5 to -3%. Dimensional deviations of 50 mm or less, with the exception of those indicated in Figures 5 and , must be established in the working drawings.
3.9. The symbolic designation of products should consist of the first one or two letters of the product, the type designation (1, 2, 3 or 4), the number indicating the size of the washbasin, the letters: D - for children's toilets, C - for washbasins with a back, bS - for washbasins without a back, p - for washbasins with overflow, SU - for washbasins with a cut corner, vp - for cisterns with a top start, bp - for cisterns with a side start, F - for porcelain items, pf - for semi-porcelain items, fs - for earthenware products and designations of this standard.
Symbol example washbasin rectangular, third size, with backrest, porcelain:
UmPr3SF GOST 30493-96
The same, a corner washbasin, with a cut corner, semi-porcelain:
UmUgSupf GOST 30493-96
The same, a bowl-shaped toilet bowl, with a direct outlet, without a one-piece cast shelf, porcelain:
The toilet bowl is installed in a specially prepared place: the pedestal is fixed with two or four bolts or screws, depending on the design of the toilet bowl, on a wooden platform or fixed with cement mortar.
On a toilet with a one-piece molded shelf, the tank is bolted to the toilet shelf.
When installing a tank mounted on a separate shelf, the rubber cuff located on the nozzle of the shelf is put on the socket of the toilet bowl and after that the shelf is attached to the toilet bowl.
The float valve must completely shut off the flow of water into the tank when the level is 20 mm below the overflow.
Installing a washbasin on metal brackets
On a pre-marked wall, two brackets are installed (with screws, bolts or by shooting) at a distance corresponding to the size between the mounting holes of the washbasin.
The washbasin is mounted on brackets and its tailgate is fixed with a bracket or in another way, providing a load on the front edge of at least 1.5 kN (150 kgf) from overturning.
Installing a washbasin on a pedestal with bolts
On the pre-marked wall, two bolts are installed at a distance corresponding to the size between the mounting holes on the rear mounting surface of the washbasin.
The washbasin is mounted on a pedestal and bolted to the wall.
The fastening must provide a load on the front edge of the washbasin of at least 1.5 kN (150 kgf) from overturning.
Open the current version of the document right now or get full access to the GARANT system for 3 days for free!
If you are a user of the Internet version of the GARANT system, you can open this document right now or request it via the Hotline in the system.