How and how to wash an acrylic bath without damaging it. Acrylic bath care: how to clean and wash at home How to wash an acrylic bathtub

Very comfortable and practical. But, like any other household item, they need daily care. Any hostess who owns this uncomplicated object of sanitary ware has ever wondered "the inside of an acrylic bath and how often to wash it at home?". We will try to help and give an answer to this seemingly simple, but very important question.

Acrylic Bathtub Daily Care

Acrylic came to the plumbing industry from dentistry. There it was widely used for lining metal frames of dentures and making full-fledged crowns. Being a durable and wear-resistant material, acrylic easily competed with steel and cast iron in the manufacture of sanitary equipment (shower trays and bathtubs).

In order not to resort to a radical cleaning method, do not allow the acrylic bath to be heavily soiled

Acrylic is a fairly demanding material. Although it is resistant to impacts, small scratches easily appear on it, which subsequently darken and spoil the appearance of the bath very much. In order to avoid the appearance of microcracks and scratches, it is necessary to observe some precautions during the daily use of an acrylic bath:

Advice! In order for your bath to shine white, you need to provide it with daily care. Avoid severe contamination. It is much more difficult to get rid of complex lime masses.

For those who daily wonder how to clean an acrylic bathtub at home, we will tell you that the best remedy for stains and plaque is prevention. It is enough after each use to rinse the bath with a stream of clean running water, the best effect can be achieved using a soapy soft sponge. And after washing, wipe dry in order to avoid drying drops of hard water on the surface of acrylic.

Strong contamination: radical cleaning methods

Even with the most careful care, serious contamination cannot be avoided. This can happen both through the negligence of the owner, and under the influence of hardness salts contained in the water masses. Also a dangerous enemy for acrylic is rust formed on damaged parts of the mixer, pipes or other metal elements. Acrylic absorbs the substance and it is not possible to remove it with a regular brush.

On the bathroom, as well as on the faucets, limescale will appear over time

For rust stains or other contamination, special acrylic cleaners can be used. But their impact will be effective only on a fresh stain. In addition, chemicals should be used very carefully and diluted with plenty of water. Otherwise, concentrated chemistry can cause even more harm. As for limescale, acrylic is also cleaned of it using special chemicals.

Important! The surface treated with chemicals must be washed as soon as possible. Left for a long time, it is absorbed into the structure of acrylic, destroying it and forming even larger stains.

Old rust or limescale stains cannot be removed by any chemical agent. More radical cleaning methods are used here. To do this, stock up on soft sandpaper and gently clean the stain with it. After that, the place of stripping is treated with polish for acrylic. This method is best entrusted to a warranty service specialist or a licensed technician.

Cleaning the whirlpool jets of an acrylic bath

The range of acrylic bathtubs is not limited to traditional products. There is a wide range of more expensive and considered elite in their category - hot tubs. The difference lies in equipping a conventional product with nozzles, into which a directed flow of water is supplied using a circulation pump.

It is very important to clean the hot tub regularly to prevent damage to the jets.

If the hydromassage function is not used regularly, the jets may develop:

• limescale;
• mold;
• fungus;
• pathogenic bacteria.

To clean such a bath, you need to carry out a number of activities.

At the final stage, clean water will wash all the nozzles from the detergent and the bath is ready for use.

Important! Do not use whiteness and other chlorine-containing preparations as a disinfectant. This is especially true for hot tubs. They not only damage acrylic, but also instantly destroy silicone and rubber seals.

Substances incompatible with acrylic

Acrylic baths are absolutely not protected from the effects of aggressive substances, so there is a large list of cleaning products, the use of which is strictly prohibited. Some of them remove the glossy sheen from the acrylic surface, while others completely destroy it.

Never use harsh chemicals to clean an acrylic bathtub.

These substances include:

• products containing fine abrasive in their composition;
• chlorine;
• acetone;
• ammonia;
• formaldehydes.

With abrasive products, everything is clear - they violate the surface of acrylic, forming small scratches on it. The fight against which will cost some physical strength and financial investment. Small cracks and scratches are rubbed with special polishes, and deeper ones are polished with soft sandpaper or a grinder, in special cases, made specifically for repair work.

Purchase special products for washing acrylic bathtubs

The decision to disinfect with chlorine can lead not only to tarnishing of the material and loss of gloss, but also to the formation of small roughnesses on the acrylic (destruction process). Acetone and other solvents, like ammonia, can also cause the bath to lose its gloss. But this is not the worst. Prolonged exposure of the solvent to the acrylic will inevitably lead to corrosion of the material and the formation of dilapidated areas.

It should always be remembered that the use of chemicals for an acrylic bath is allowed no more than 1-2 times a month when carrying out a complete disinfection of the bathroom. On other days, it is best to resort to scheduled cleaning and use the least aggressive preparations: soap, soft cloth or sponge.

Cleaning products from improvised materials

Not everyone trusts chemical cleaners. In some cases, they can lead to disastrous consequences for acrylic. Sometimes the cost of products is beyond the buyer's pocket. Or the user is allergic to the chemicals. In such cases, the cleaning agent can be prepared according to folk recipes using improvised products, most of which are in the kitchen of any housewife.

There are many other ways to clean acrylic from stains, but the best of them is prevention. Avoid plaque deposits. Rinse your bathtub after every use and your bathtub will be sparkling clean for years to come.

Acrylic bathroom care: video

Acrylic bathtubs are increasingly being chosen by consumers to replace worn-out steel and heavy cast iron bathtubs. Indeed, such plumbing fixtures are characterized by a very attractive, neat appearance, they are light in weight and exceptionally white. In addition, they are presented in a very wide variety of shapes and sizes.

In addition, acrylic products have a number of other advantages, one of which is complete inertness to corrosion. However, this does not relieve the owners of the obligation to regularly clean surfaces. And in general - taking care of an acrylic bathtub at home should be systematic - only in this case it will retain its original novelty for many years. By the way, similar rules should be followed by those homeowners who have updated old steel or cast-iron bathtubs with acrylic tabs.

Properties of acrylic bathtub surface

In the production of acrylic sanitary ware accessories, a special polymer is used, which is characterized by sufficient hardness and wear resistance. But it is impossible to consider it devoid of shortcomings.

Since the "pros" and "cons" of acrylic products directly affect both the rules for their operation and recommendations for regular care, it makes sense to list them briefly.

First - about virtues :

• Such baths retain the heat of the water collected in them much better and longer. For this reason, it is more comfortable to take procedures in them.
• The vulnerable point of cast iron and steel bathtubs is always the enamel layer. In the case of even a small cleavage, a corrosion center is formed. With acrylics, there is no such danger.
• Acrylic bathtubs have dirt-repellent properties. This prevents the formation of a favorable environment for the development of microflora in the pores of the material, which is especially important under conditions of constant humidity and elevated temperature.
• In continuation of the previous paragraph - the surface of the acrylic bathtub is easily cleaned of dirty deposits (unless, of course, it is not running at all) .
• The lightness of the products greatly simplifies both transportation and installation.
• Finally, the manufacturing technology of such bathtubs allows the production of products of various designs - in shape, size, color, equipment. That is, the proposed choice of models is incomparably wider than steel or cast iron.

But limitations There are also, and - very significant:

• The material is resistant to high temperatures. It is clear that the critical threshold of 160 ℃, which causes acrylic to melt, is impossible even theoretically in a bathroom, but even very hot water, combined with mechanical stress, sometimes leads to deformations. Especially if the bath is from the category of inexpensive, thin-walled ones.
• The strength qualities of many acrylic products cannot be called outstanding. Often you can clearly feel the deflection of the bottom of the bath under your feet, which already causes a certain psychological discomfort. In addition, along with such plasticity, fragility is also noted - the instability of the walls to accentuated mechanical loads - shocks. Often this ends with the formation of a crack.
• Acrylic is still quite sensitive to household chemicals. That is, it is unacceptable to use recklessly any detergents and cleaning products, since you can hopelessly ruin the bath.

The disadvantages include the rather high cost of acrylic bathtubs. And also the fact that the market is flooded with low-quality, handicraft products, which, however, with the “naked eye” are difficult to distinguish from those worthy of attention. But such a bath will definitely not serve for a long time.

Basic rules for the care of acrylic surfaces

Owners who are well versed in caring for them will confirm that keeping them in proper condition is quite easy, although this will take some time. It is enough to wipe the inner surface of the bath with a soft cloth dipped in warm water after each intake of water procedures, and then it is advisable to wipe it dry. In this case, the best solution can be considered to reduce to a possible minimum the use of chemicals for cleaning acrylic. The complexity of maintaining accessories made of this material lies only in the fact that sometimes there is not enough time and effort for daily cleaning.

• It has already been noted that acrylic surfaces are not sufficiently resistant to mechanical stress. And, by the way, most often scratches on bathtubs appear precisely in the process of cleaning them. Therefore, sponges with an abrasive surface should be categorically excluded from use. Only soft sponges or cloths are suitable for cleaning.
• Modern models of acrylic bathtubs are more durable than those that appeared at the dawn of the spread of this technology. However, some care must be taken when using them. Chips on acrylic can appear as a result of falling into the bath of various metal or sharp objects, glass, porcelain or faience dishes, so you can not store this on the shelves located above the bath.

• You should know that there are two types of acrylic products made using different technologies - these are cast and reinforced bathtubs. Their surface care is the same, but they differ in mechanical resistance.

Reinforced products consist of several layers, the middle of which is fiberglass with the addition of epoxy resins. Reinforcement makes the container more durable, but at the same time increases the risk of chipping. When heavy objects fall on such a surface, part of the outer acrylic layer may peel off and break off.

Cersanit acrylic bath prices

Cersanit acrylic bathtub

Cast containers are more susceptible to damage in the form of scratches. But sometimes, especially if the frame is not properly installed under the bath, it can simply split.

• It is not recommended to soak laundry in an acrylic container. The fact is that prolonged exposure of this material to an aqueous solution of powder, as well as contaminants separating from the fabric, negatively affects the surface of the material. The bath will quickly lose its whiteness and smoothness of the walls.

• If it is fashionable to clean sanitary ware with most of the usual detergents, then special compositions should be chosen for acrylic. In the same case, when it is not possible to purchase them constantly, you can use home remedies with a mild cleaning effect. When choosing a ready-made composition for washing an acrylic surface, you should carefully study its packaging, which indicates the ingredients, as well as its purpose.
• If it is decided to use ready-made chemical compositions for cleaning the bath, it should be remembered that they are recommended to be used no more than once every 10-14 days. Otherwise, the surface will lose its smoothness and whiteness. In the period between “general” cleanings, it is necessary to use only a damp sponge or napkin.
• It is impossible to use ordinary powder, liquid or pasty detergent compositions with abrasive inclusions for washing polymer plumbing. They are able not only to leave scratches on the surface, but also to make it completely matte. And this will lead to the fact that the mud particles will linger on the walls of the bath. Getting rid of such a stubborn plaque is already much more difficult.
• It is unacceptable to clean bathtubs made of acrylic with products containing oxalic acid, alcohol-containing solvents, and acetone. These substances can not only destroy the gloss, but also deform the polymer product. Cleaning agents containing chlorine can also damage the surface of the material.
• It is impossible to bathe pets in acrylic or acrylic-coated bathtubs, as they can scratch the surface of various depths with their claws. If it is necessary to carry out such measures, the bottom, as well as the walls of the container, should be secured by covering them, for example, with old towels.
• Do not clean dishes in the bath, as well as objects made of any material that have sharp corners that can damage the surface.
• The bath will lose its original aesthetic appearance if it is filled with boiling water or water heated to a temperature exceeding 65 degrees. Under the influence of high temperature, acrylic will not only lose its smoothness, but may also deform.
• It is unacceptable to clean the inner surface with hard brushes.

All of the above precautions are necessary to keep the tub in its original white and smooth condition. Therefore, when purchasing an acrylic product or producing it, it is necessary to take into account all the indicated points.

What compositions can be used for acrylic plumbing?

It should be told in more detail about ready-made detergents suitable for cleaning polymer baths - what you need to pay attention to when choosing them.

• The packaging of specialized compounds should indicate that they are safe for sanitary accessories made of acrylic.
• In addition to specially designed acrylic cleaning compounds, some universal solutions are also suitable, but they should not contain aggressive ingredients, such as certain types of acids, acetone, alcohol and ammonia.

The disadvantage of ready-made detergents for acrylic products is their high price, as well as the fact that their use must be strictly dosed. It should be noted that domestic cleaning solutions have a more affordable price, although they often have a completely similar effect to imported compositions.

Ready-to-use proprietary acrylic care products

The advantage of ready-made chemical-based cleaners is that they not only remove dirt, limescale, rust and yellowness from acrylic, but also create a protective, visually imperceptible film on its surface.

So, among all the existing compositions for cleaning acrylic, the following compositions can be distinguished, which have earned positive user reviews:

Illustration	Name and brief characteristics of the detergent
	"Acrilan" - this composition is a cleaning foam designed to eliminate contaminants such as limescale, soap streaks and rust. The tool easily copes with different types of stains. After washing off the foam, a protective film remains on the surface of the acrylic, which prevents the accumulation of dirt in the pores of the material. For the composition to be effective, it should be used in accordance with the instructions supplied by the manufacturer. It is very important not to leave the foam applied on the surface until completely dry. In addition, it is unacceptable to mix "Acrilan" with other detergents.
	"DEC" - this product is produced in the form of a cream and is intended for cleaning not only acrylic sanitary ware, but also tiles, chrome and other surfaces. The composition includes antiseptic additives that prevent the growth of harmful bacteria and fungal growths in hard-to-reach places of plumbing accessories. Along the way, when flushing, the product perfectly cleans the sewer system. It has a beneficial effect on the metal parts of hydromassage bath models.
	"Triton" is a fairly popular product for cleaning acrylic bathtubs, which can be sold as a concentrate or a ready-to-use solution. The concentrate is sold in large containers and is intended for the active fight against serious pollution and for large-scale sanitization from the spread of bacteria. The solution is usually packaged in a spray bottle, used to remove limescale and grease stains, as well as disinfect the bathtub.
	"Mr. Chister" - is used not only to tidy up acrylic bathtubs, but also metal plumbing accessories. The product perfectly copes with rust, limescale, grease stains and soap stains, while being gentle on surfaces and not causing them mechanical damage. The composition of "Chister" includes a polymer additive that creates a film on the surfaces that prevents the formation of dirt deposits. Antiseptic additives protect bathtubs or sinks from the growth of bacteria and fungal colonies. The tool works quickly, so you do not have to wait a long time for its effect on the material being cleaned.
	"Cif" - this tool familiar to all Russians has several lines, some of them are also suitable for cleaning acrylic accessories. Cif is produced in the form of a cream and spray, which are used mainly for preventive measures. Thanks to this composition, acrylic more effectively resists adhesion and penetration of mud deposits into the pores of the material. However, with strong pollution, limy deposits and a mold of "Cif" does not cope.
	"Meine Liebe" goes on sale in the form of a spray. Shows high efficiency in the fight against rust spots, mold and limescale, and also removes unpleasant odors. The product has a fruity aroma, and it contains citric acid, which is the main active ingredient. "Meine Liebe" creates a protective film on the surfaces, thanks to which the bath will remain clean for much longer. The spray is quite economical, so one bottle lasts for a long time, and it is also environmentally friendly, as it does not contain toxic ingredients.
	"UNICUM" is produced in the form of a spray designed to clean acrylic from mold, lime and rust. Due to the release form, the agent can be applied to the most contaminated areas of the bath. After 15 ÷ 20 seconds, the spray is rubbed with a soft cloth, and then washed off with warm water, along with which the impurities are also removed. "UNICUM" takes care of the cleaned materials, while producing high-quality cleaning with low consumption of detergent. After washing off the cleaning composition, a protective film remains on the acrylic.
	"Sanfor Acrylight" - this composition is intended for major cleaning, disinfection, as well as updating acrylic bathtubs and shower trays. In addition, the product effectively cleans the whirlpool systems. With the help of "Acrylight" even the most chronic pollution, limestone and soap deposits are removed. At the same time, the composition works effectively, creating a protective film on the surfaces, extending the service life of accessories, facilitating their care, and also giving gloss for a long time.
	"Cinderella" is an effective cleaner for acrylic products, which can be an ideal option for those who have not yet decided which of the compositions to choose. It perfectly copes with all the pollution that occurs on acrylic. However, "Cinderella" has one significant drawback - it is a pungent odor that appears during cleaning. Therefore, for work, it is recommended to wear protective gloves on your hands, and to protect the respiratory tract with a mask. The applied agent is left for seven to ten minutes, and then washed off with warm running water, after which the surface is wiped with a soft cloth.

We should never forget that chemicals can become both a reliable assistant in removing contaminants, and a "pest" that will completely ruin the acrylic surface. Therefore, they should be used no more than once or twice a month. For more frequent cleaning of acrylic products, less aggressive compounds should be used.

If one of the chemicals is chosen for cleaning the bath, then before applying it to the entire area of ​​\u200b\u200bthe container, it is recommended to use it on a small, not too noticeable area of ​​\u200b\u200bthe surface. If acrylic does not show a negative reaction, then you can proceed to "full-scale events."

Available means for cleaning acrylic

Substances that can be found in any kitchen or in a home first aid kit are not so aggressive. They have a softer effect on acrylic, and at the same time, they do a pretty good job with most contaminants.

These products include citric acid, baking soda, vinegar, laundry soap, hydrogen peroxide, potassium permanganate. They can be applied once to twice a week without affecting the material.

• Citric acid must be dissolved in warm water, after which the solution is applied to the contaminated areas of the bath. For the manufacture of this composition will require 250 ml of water and 100 grams of crystalline acid.
• Baking soda (2 ÷ 3 tablespoons) must be poured with 500 ml of hot water, which will extinguish and dissolve it. After the reaction is over, 500 ml of cold water must be added to the solution. The warm composition is applied to the walls and bottom of the bath for 10-15 minutes. After that, the container is rinsed with warm water.
• Laundry soap (15 g) must be grated on a coarse grater, pour 500 ml of hot water and, stirring, achieve complete dissolution. Then one tablespoon of soda is added to the soap solution. The resulting mixture is applied to the walls of the bath and left for about half an hour. After that, rinse with warm water, while wiping with a clean cloth.

If we talk about pollution of a certain nature, then the following recipes are used to remove them:

• A not too thick layer of limescale can be removed with citric acid or concentrated lemon juice. To do this, the bath must be filled with hot water, the temperature of which should not exceed 60 degrees. Then 100÷150 g of citric acid is poured there and mixed well. You can pre-make a saturated solution of acid, which will disperse faster in a large volume of the bath. Drain the water into the sewer after two to three hours after filling the bath, after which it must be rinsed with warm running water.

• If limescale has already formed a rather thick layer due to oversight, then you can try to cope with it by treating it with soda and then with vinegar. To do this, a soda solution is applied to the surface (1000 ml of water and 100 g of soda), on top of it is an acetic composition (water and 9% vinegar, taken in a 1: 1 ratio). A reaction should occur between soda and vinegar, which lasts about 5 ÷ 7 minutes. Upon completion, the surfaces are washed with water. If necessary, this cleaning process should be repeated.
• Yellow spots and rust that has not eaten into the pores of the polymer must be treated with soda or hydrogen peroxide. The compositions are applied and left for 15–20 minutes, and then washed off with warm water.
• Not very deeply ingrained stains, mainly appearing on the sealant around the perimeter of the bath, can be removed with hydrogen peroxide.
• Rust most often appears on the surface of bathtubs due to a leaking faucet. If the stain is ingrained, and none of the ready-made or improvised compositions no longer acts on it, then it should be carefully rubbed with fine-grained sandpaper. After that, the cleaned place must be treated with a special compound - polish for acrylic. It is necessary to act very carefully, otherwise you can only worsen the situation.

Daily bathroom care

As mentioned above, in order to avoid lengthy procedures for cleaning complex stubborn stains and streaks, it is advisable to at least lightly wash the bathtub after each water treatment. Such a process will not take much time, as it consists of very simple manipulations:

• The sponge is lathered with any soap, and to speed up the procedure, it is better to use liquid types of soap.
• Then all the surfaces of the bath are rubbed with this sponge.
• After that, the container is rinsed abundantly with warm water.
• The final obligatory action is to dry the bathtub with a cloth that absorbs moisture well.

Such actions will prevent the appearance of stains and plaque, and, most likely, completely eliminate the need to use chemical detergents. Thanks to this, the bath will last much longer without losing its original fresh look.

Find out and also get acquainted with ready-made compositions and folk remedies from our new article on our portal.

Features of the care of the bath with hydromassage

Daily cleaning of a bathtub equipped with a hydromassage is carried out in much the same way as a regular acrylic container. However, with a certain regularity (once a week or once a month, depending on the frequency of use of the bath), it is necessary to carry out a more extensive cleaning, including several specific operations.

• The bathtub is filled with warm water so that it covers all hydromassage nozzles.
• Then concentrated lemon juice (100 g) or a solution of citric acid prepared from 100 g of crystals dissolved in 200 ml of warm water is poured into the water.
• The bath is left with water for 2÷3 hours, after which the water is drained.
• From the bottom of the bathtub, the rest of the solution is collected with a sponge, and its walls are again wiped with it.
• Next, cotton swabs are taken - they will be required to clean the holes of the nozzles of the hydromassage system. The stick is moistened with hydrogen peroxide and penetrated as far as possible into the holes, thus cleaning them from limescale.
• The final step is rinsing the entire bath with warm water and wiping it dry with a soft cloth.

This process will not only clean the acrylic surfaces, keep the walls and metal parts looking fresh, but will also help ensure the long-term efficient operation of the hydromassage system.

In order to prevent contamination of the hydromassage tubes, it is recommended to carry out preventive measures, consisting of the following actions:

• Before taking a bath, it is filled with water, and the hydromassage system is turned on for 5÷7 minutes, even if it was not planned to be used. In this way, stagnation of water in the internal channels, which often results in lime deposits, can be prevented.
• Once a month, a more intensive cleaning procedure should be carried out. To do this, the bathtub is filled with water, to which a special cleaning agent is added, and in this switched on state it is left for 10÷20 minutes. After that, the water is drained, the bath is rinsed and wiped dry.

How to get rid of minor scratches and other damage?

Even with the most careful use of acrylic sanitary ware, it is often impossible to avoid scratches on their surface. Lime and rust deposits can accumulate in such damage, which immediately visually distinguish these areas from the general background. To get rid of scratches, you can use one of the existing methods for removing them.

• Superficial scratches can be removed in the same way as single rust spots by treating the surface with fine-grained (P240÷P280) sandpaper. After that, the leveled area is polished with a polish specially designed for acrylic.

• Sometimes it is enough to apply only polish to scratches, without the use of a preliminary abrasive effect. The polishing paste is applied and intensively rubbed into the surface with a piece of felt in a circular motion. The process is continued until the scratches and the applied composition are maximally smoothed.

• If deep damage occurs, a repair kit for acrylic plumbing accessories will help. It is recommended to purchase it together with the bathroom in order to immediately select the closest shade of color - it will be much more difficult to do this later. The kit includes a paste-like acrylic compound that hardens when applied to the bathtub surfaces. The paste is filled into scratches and rubbed in a circular motion with the help of felt until it becomes smooth.

• Acrylic paste can even be used to repair through holes in a cast bathtub model that may also be formed for one reason or another. To perform this procedure, the area to be repaired must first be cleaned. Further, several layers of high-quality waterproof adhesive tape are glued on the outside of the bath, which will become a barrier for the paste. Then the resulting hole is filled with liquid acrylic and leveled with a plastic spatula. After that, the patch must be left until the paste hardens for two to three hours. Next, the acrylic is sanded with fine-grained sandpaper and polished with a piece of felt.
• The method of filling with acrylic can also be used when it is necessary to remove deeply ingrained stains, after the elimination of which, depressions remain on the surfaces.
• Another option for sealing through holes in the bath involves the use of polymer putty. It fills the resulting hole and waits for it to dry completely. After that, acrylic paste is applied on top of the putty and leveled with a spatula. The dried paste is processed with fine-grained emery, then, if necessary, painted, and the final step is the final polishing of the area to a perfectly smooth state.

It is quite obvious that, if desired, the owners can not only carry out ordinary cleaning, but also restore damaged areas of acrylic bathtubs without resorting to the help of a master.

Prices for popular acrylic bathtubs

In conclusion of the publication, summing up all that has been said above, we can repeat ourselves somewhat, highlighting the key points that are important to consider when caring for acrylic plumbing fixtures:

• In order not to engage in a very laborious, time-consuming and effort-consuming job of cleaning a heavily polluted bath, it is recommended to wash it regularly, after each intake of water procedures.
• It is necessary to monitor the serviceability of the water taps and the shower - there should not even be signs of water leaks anywhere. All faucets should be tightly closed after each use. This way you can avoid the appearance of stubborn yellow rust spots on the surface of the bowl.
• It is recommended to rinse the tub with hot water, which will make the acrylic shine.
• Before choosing and applying a new detergent, you should carefully study its composition and method of application. It is better to test it on an inconspicuous small area of ​​\u200b\u200bthe surface.
• It is necessary to protect acrylic surfaces from mechanical influences, from contact with sharp objects, as well as from the claws of animals.
• Do not place a stool on the bottom of the bathtub, using it, for example, as a basin support during hand washing. The point pressure of its legs will certainly damage the acrylic surface.
• In case of contact with the surface of coloring substances, they should be removed immediately, preventing them from soaking into the pores of the polymer. Stubborn stains will be very difficult to remove.
• It is recommended to keep the bath in a dry state, so it is advisable to wipe it after each use and cleaning with a soft, well-absorbing cloth.

* * * * * * *

If you understand well all the nuances of the care of acrylic baths and their minor repairs, it will be easier to deal with both prevention and cleaning. The main thing is not to make hard-to-correct mistakes in this matter. In addition, who knows, it is possible that, after reading the information, some homeowners who are thinking of replacing their steel or cast iron model with a fashionable acrylic model will completely abandon this idea.

In conclusion - an informative video dedicated to the care of an acrylic bath.

Video: How to get rid of yellowness in an acrylic bath

Acrylic bathtubs have won the love of hostesses all over the world with their smooth surface, glossy sheen and flawless whiteness. Lighter, plastic models of various shapes and sizes have successfully replaced clumsy cast-iron washing containers.

Happy owners of acrylic sanitary ware often wonder how to wash the font in order to preserve the original appearance of the product for a long time. In fact, care should be taken in this matter, since not every detergent is suitable for mechanically fragile plastic. In this article, we will tell you how to care for an acrylic bathtub so as not to spoil it.

Advantages of acrylic

Many homeowners are concerned about how to clean an acrylic bathtub, as they have heard about the capriciousness of plumbing fixtures made from this material. In fact, acrylic products are much easier to care for than steel or cast iron wash basins.

Ease of cleaning is due to the following properties of the polymer:

• Low porosity. There are practically no pores on the acrylic surface, so it does not absorb dirt, but repels them, so that daily cleaning of the acrylic bath can be done simply with warm water and a soft cloth.
• High smoothness. The smooth surface of acrylic does not allow dirt and harmful microorganisms to clog into the structure of the material, so it is easy to clean the bowl even without the use of abrasive detergents.

Note! Manufacturers often talk about the "self-cleaning effect" that high-quality acrylic products have. This term means that their ugly surface repels dirt, so you have to clean the bath less often. In most cases, you can wash the acrylic bath with warm water or soapy water.

Typical pollution

Since polymer plumbing fixtures have replaced cast-iron and steel ones relatively recently, the question of how to clean an acrylic bathtub at home is relevant for many responsible housewives. Acrylic products repel dirt, however, intensive use of the device leaves its mark, which worsens the appearance and hygiene of the wash container. Most often in the process of using the bath, the following pollution occurs:

Important! Properly caring for plumbing so that old stains do not appear on it is much easier than washing an acrylic bathtub. Therefore, it is important to regularly rinse the inside of the bowl with running warm water, and then wipe it dry with a soft cloth after each use.

Many housewives do not know how to clean an acrylic bathtub, so they use completely inappropriate products that corrode, scratch or otherwise damage the product. Improper care is the most common cause of premature wear of acrylic sanitary ware. Manufacturers recommend that you refrain from using powders for cleaning such bathtubs, instead it is better to use a delicate, gentle washing gel or cream. To care for acrylic sanitary ware, 4 categories of cleaning products are used:

Please note that if you are not sure how to wash an acrylic bathtub, it is better not to risk it in vain. It is better to try what effect the composition will have on a small area of ​​\u200b\u200bthe surface, and only after that continue cleaning the product.

"Forbidden" tricks

High quality acrylic plumbing is just a godsend for modern housewives who save time on everything they can. With proper use, it retains whiteness and shine even without the use of special tools. However, washing an acrylic bathtub with the wrong household chemicals can ruin the product. Manufacturers recommend not to use for care:

Prevention

An important measure to combat contamination on the surface of acrylic hot tubs is proper care in compliance with the manufacturer's recommendations. Properly using the product is much easier than washing an acrylic bath at home. Compliance with these 4 simple rules will significantly shed the life of plumbing:

Remember that using a low-quality or inappropriate acrylic bath cleaner, you are not getting rid of pollution, but of expensive plumbing!

Video instruction

Acrylic and acrylic coated bathtubs are popular among buyers. They are lightweight, practical, versatile in form and function. However, the care of such plumbing has its own characteristics, so the question of how to properly clean an acrylic bathtub is always relevant.

Acrylic polymer was originally used in dentistry. But due to its strength, low thermal conductivity and antibacterial properties, it soon began to be successfully used in a wide variety of industries.

Among positive qualities acrylic sanitary ware

• Lightness and strength. The standard model weighs no more than 30 kg, which is significantly less than that of the cast iron model. At the same time, they are durable, this is facilitated by a rigid frame, which is used in the design. Maximum weight (load) - 400-500 kg.
• Variation in the execution of models. Sizes, colors, shapes - according to the number of proposals for the specified parameters, acrylic bathtubs deservedly occupy the first place.
• Low thermal conductivity. The model with acrylic coating perfectly retains heat and is pleasant to the touch.
• Appearance. If such a bathroom is properly and regularly looked after, it will retain its original color and glossy shine for a long time.
• Useful additional features. For example, you can choose a bath with hydromassage.
• Noise isolation. When faced with an acrylic coating, water does not make a lot of noise, as is the case with a steel and cast iron bath.
• Ease of installation. The metal frame is easy to install and adjust.

Minuses acrylic bathtubs:

• Fragility, flexibility. In such a bathroom, you can not drop heavy objects, as well as put iron buckets, basins, etc. in order to avoid chips and scratches. Also, improper installation of the frame over time will lead to a curvature of the bathroom.
• Temperature stability. This is typical for budget models that are covered with a thin layer of polymer.
• At a sufficiently high cost, they limited period of use.
• And the main disadvantage : When using conventional plumbing chemicals and cleaning powders, the acrylic coating dulls, scratches and becomes clogged with dirt. Therefore, special household chemicals are intended for acrylic.

Substances that destroy acrylic

• Powders and detergents containing abrasive particles. This also applies to dry soda. They provoke the appearance of micro-scratches, which make the surface matte and prone to contamination.
• Chlorine containing products. They destroy the upper protective layer, as a result of which acrylic plumbing tarnishes, loses its characteristic glossy sheen. In whirlpool tubs, bleach can damage rubber and plastic parts.
• Acetone and similar solvents. They destroy the structure of the polymer that makes up acrylic. If the contact is long, the bath is deformed.
• ammonia, formaldehyde. They give a similar effect as solvents.
• Concentrated alcohols, alkalis and acids, as well as the means in which they are included. Exposure to these caustic chemicals gradually destroys the acrylic, leading to the formation of small cracks.
• Metal brushes and scrapers, hard sponges and rags- a taboo for such plumbing.
• Boiling water. High temperatures can cause the bathtub to warp, so use water no higher than 70 degrees.

Folk remedies

• Dishwashing liquid, shower gel, liquid soap although they do not act on old deposits and plaque, they are suitable for daily preventive care.
• Toothpaste with whitening effect. It is convenient to apply this method to local pollution. The paste is applied to the stain and rubbed, then washed off with water.
• It is impossible to clean an acrylic bathtub with dry soda. But it is allowed to use a paste made from soda, soap and water. Pour the baking soda powder into the soapy water and knead the paste.
• Lemon acid. It will remove limescale and whiten the surface. Procedure: draw hot water, pour lemon - 1 pack. Wait 2 hours, drain the solution and rinse with water. This method can be used no more than 1 time in 6 months.
• Suitable for stubborn dirt vinegar. Procedure: draw warm water into the bathroom and pour a bottle of 9% acetic acid. After 12 hours, drain the solution into the sewer and rinse the bath.

professional tools

If folk methods did not help, you can use special cleaning products. Among the popular:

• cif. This cleaning cream can be used not only for acrylic bathtubs, but also for other sanitary ware. Effectively and gently removes various types of dirt.
• "Acrilan". Produced in the form of foam, which is applied to the pollution for 10 minutes. Then it must be washed off and wiped dry. The foam must not be mixed with other products and allowed to dry on acrylic.
• Bass. It is presented in the form of a spray, which is convenient to spray. After use, it must be washed off.
• "Cinderella". Fast acting, strong fragrance. It should be applied with rubber gloves. The result of cleaning will be noticeable in a few minutes. According to the instructions, it is recommended to wait 7 minutes, and then rinse with plenty of water and wipe dry.
• Another special detergent Ravak. Available as a spray or paste by the manufacturer of acrylic bathtubs.
• "Chister", "Team-Profi" - These special tools are used in the same way. They are applied to the surface, wait for the time indicated in the instructions, then washed off and wiped dry.

Carefully! The bath will be able to clean white "Pemolux", "Sanoks", "Domestos". But they contain aggressive hydrochloric acid, which destroys the protective coating. Immediately after cleaning, the bath will become snow-white, but then the dirt will stick to it many times faster. Therefore, such means cannot be used.

How to get rid of various types of pollution

How to clean an acrylic bathtub depends on the type of dirt that has appeared on it. Typical - water stone, limescale, rust.

Water stone and limescale

Water stone or limescale will form on the bowl if tap water contains a lot of metals in the composition. If the water is just like that, then it is better not to allow the stratification of the stone. To do this, after each use, wash the bath with warm water. If the bath is still yellowed, then you can deal with pollution like this:

• Fill the bathroom with water at a temperature of 25-30 degrees. The water level is such that sediments are completely under it.
• Pour in half a bottle of vinegar and add 1 package of citric acid.
• Stir and leave overnight, if possible, then for 12 hours.
• Drain and rinse off the remaining solution, wipe dry.
• If this procedure did not help, then the acrylic bathtub should be cleaned from yellowness with special products recommended by the manufacturer.

Rust

It will work to clean the acrylic bathtub from rust, but you need to do it correctly. Rust adheres strongly to inexpensive acrylic bathtubs that are only coated with polymer. Yellow rust spots are the result of unfiltered tap water and faulty plumbing.

Advice! After each use of the bath, it should be washed with water and wiped dry. If rusty streaks still appear, you should fight them.

Lemon acid. Dissolve 1 package of citric acid with 200 ml of water, stir until the acid crystals dissolve. Apply with a sponge or soft cloth to contaminated areas. Wash off with warm water.

Ammonium chloride and peroxide. From rust stains, you can very carefully use a mixture of ammonia and hydrogen peroxide. These components must be mixed in equal parts, wet the sponge and rub the dirt. The result will be noticeable immediately.

Disinfection

Many models of acrylic bathtubs have an antibacterial coating, so they do not suffer from mold and fungi. But prevention will not be superfluous, especially if there are small children.

Important! For disinfection, you can use only special substances for acrylic, safe for coating.

Regardless of the medium, the disinfection process is as follows:

• Pour warm water into the bath.
• Add the required amount of disinfectant.
• Leave for 15 minutes, then drain.
• Wash off the remnants of the product.
• Wipe dry.

The frequency of such treatment depends on the type of product chosen, but it is recommended to carry it out at least 1-2 times a year.

Features of cleaning bathtubs with hydromassage

The whirlpool bath is equipped with special nozzles that are connected to a circulation pump. It is he who creates the pressure of water, which, under strong pressure, exits through the nozzles in a given direction. Moisture must not accumulate in the nozzles, as this leads to the growth of mold and the multiplication of microorganisms.
The process of cleaning such a bath is as follows:

1. The bowl is filled with hot water, the level is 5-7 cm higher than the nozzles.
2. The water circulation is turned on.
3. 50 ml of liquid is poured into the bath, which is used to clean dishwashers.
4. The hydromassage mode is activated for 15 minutes.
5. It remains to drain the water and start the hydromassage mode with clean water. This will help clean the injectors.

Removing scratches from an acrylic bath

Caring for an acrylic bath includes timely removal of scratches. This should be done as soon as you notice a defect, since even a small damage can lead to the destruction of the entire product.

liquid acrylic

Acrylic restoration kits can be purchased at a plumbing store. Individual manufacturers sell an acrylic bath along with such sets. The kit includes:

1. Epoxy putty.
2. liquid acrylic.
3. Putty knife.

Such restoration can save even very deep scratches. The kit components are toxic and must be handled with care.

Recovery steps:

1. Treat the scratch with sandpaper.
2. Degrease and apply putty.
3. Dry. This will take about 24 hours depending on the type of putty.
4. Apply liquid acrylic with a brush and cover with polyethylene. Remove the film after 2 days.
5. Processing with fine sandpaper.
6. Polishing.

All actions are carried out very carefully so as not to damage the entire acrylic surface of the bowl.

Camouflage pencil

A special camouflage pencil will help to hide damage on acrylic. It does not contain toxic components, but it perfectly fills the scratch and restores the primary appearance of the surface. This method can be called emergency, because it gives maximum efficiency if applied immediately after the formation of a scratch.

enamel paint

Another option for masking scratches is to use enamel paint. The process looks like this:

1. Treat the scratch with sandpaper. Then remove the dust and wipe with alcohol to degrease the surface.
2. Use a brush to apply paint to the scratch.
3. Dry. This will take about 24 hours.

This method works well with shallow scratches. If the damage is deep, then pastes and putties cannot be dispensed with.

In order for the acrylic bath to last longer, you should follow the rules for caring for it. Among the main ones:
1. Rinse with warm water after each use, dry with a towel.
2. Use special delicate sponges for washing.
3. Do not drop heavy objects into the bathroom, but place metal containers on a rubber mat.
4. Do not wash pets in such a bathroom.
5. Conduct regular disinfection - at least once every 6 months.
6. Use restoration kits for restoration.
7. Do not take water with a temperature above 70 degrees.

Acrylic bathtubs, due to their excellent physical parameters and wide price range, are in great demand among the consumer. But unlike enameled metals, acrylic is more demanding on care products. After the acquisition, any user faces the question - how to clean the acrylic bath at home, because if not properly maintained, the coating can be irreversibly damaged and the product will have to be disposed of.

When choosing a means for washing acrylic bathtubs (liners), they consider chemicals sold in the distribution network specifically for care purposes or used in everyday life. It is useful for the user to know the methods and reagents used for cleaning bathtubs from various contaminants: rust, hardness salts, colorants, silicone sealants.

Synthetic acrylic, like other popular polymers (PVC polyvinyl chloride, PE polyethylene), is characterized by the fact that there are some chemicals that have a negative effect on it. Therefore, you should know which materials and components should be completely excluded when caring for an acrylic bath. This list includes:

abrasive substances. Cleaning acrylic bowls with household chemicals containing small particles of abrasives (Pemolux powder, dry caustic soda and baking soda) leads to scratches on their surface, resulting in loss of gloss, aesthetic appearance - a glossy bowl becomes matte. In addition, a rough surface after the use of abrasive materials absorbs dirt much better and is more difficult to clean in the future. You should not rub the acrylic bath with hard synthetic brushes - they increase the roughness of the walls and make further care more difficult.

Recently, in everyday life, housewives have been very popular with the Chinese melamine sponge, which works on the principle of an eraser that erases any dirt. Since the tough fibers of melamine are abrasive to materials, do not use a sponge to clean acrylic bathtubs.

Means of household chemicals. Some household sanitary products (Santeks, Sanfor) or bleaches (Whiteness, bleach) contain chlorine, which has a mild negative effect on the acrylic coating, causing the gloss to dull. Due to the low concentration of aggressive chlorine and the short exposure time, the use of these compounds does not cause too noticeable damage, but it significantly exceeds the benefits of using chlorine-containing components.

Clean acrylic is not damaged by such commonly used household products as gasoline, ammonia, alkalis, sealant, silicone lubricants, but it is better to avoid contact of these substances with the bath, as there is not always a guarantee of purchasing a quality bowl.

Acrylic dissolvers. Technical acetone, popular in everyday life, when it comes into contact with the gloss of the bowl, partially dissolves acrylic with the formation of a cloudy coating on the surface; with prolonged exposure, it gradually dissolves the polymer. Acrylic can be harmed by high concentrations of hydrofluoric and cyanic, nitric, chromic and sulfuric acids, the damage depends on the contact time of the materials.

The worst enemies of sanitary acrylic are its solvents: ketones, chlorinated hydrocarbons (chloroform, methylene chloride, dichloroethane), esters and aldehydes, alcohols (methyl, propyl, butyl, ethyl). Perfectly dissolves acrylic adhesive for PVC CosmoFen with vinyl chloride polymers in the composition.

Household chemicals

The distribution network sells a wide range of products for the care of acrylic surfaces, their distinguishing feature is the Acrylic inscription on bottles or containers. The consumer is well aware of such brands as Bass, Sif, Cinderella, Chister, Ravak, Acrylan, Sanoks, Silit, Tim-Profi, produced in the form of gels, pastes or spray liquids.

On the packaging of each composition there is an instruction manual, the standard cleaning method is to apply (spray) on the bowl and wash off the plaque with warm water after a while. Most popular gels are squeezed onto a rag (sponge), smeared over a bowl, holding for 15 minutes, and removed with hot water, then wiping dry.

Folk remedies for washing acrylic bathtubs

Due to the low cost, availability and wide range of household chemicals, the use of folk methods for cleaning bathtubs is not as relevant as in the days when acrylic plumbing first entered the distribution network. However, the desire to get ahead of industrial chemistry in efficiency or save money through the use of cheap home components still does not leave many owners. Thanks to their ingenuity, the following methods for cleaning acrylic bathtubs with household products are recommended:

Lemon acid. It is used to clean painted bowls from hardness salts and yellowness that are clearly visible on their surface. To use citric acid, a sachet of powder is diluted in approximately 0.5 liters of water, the finished solution is poured into a household spray bottle and the surface of the bowl is moistened with liquid in places where plaque appears. The operation is repeated several times, at the end of the procedure, citric acid is washed off with hot water from the shower head.

soda and vinegar. This combination is a universal household method for cleaning any surfaces, ranging from metal utensils, frying pans, gas and electric stoves, sewer pipes, and ending with plumbing fixtures. To eliminate rust spots or other dyes, baking soda is poured onto the area to be cleaned, sprayed with 9% vinegar essence from a household spray bottle. At the end of the cleaning work, the plaque is washed off with hot water.

Toothpaste. Toothpaste (not gel) can remove rust marks from an acrylic bowl by applying it to an old toothbrush and rubbing it into the stain. If the whole bath has lost its luster, you can return it to its original state by rubbing the entire surface with paste, for this it is applied to a cloth and rubbed into the bowl for a certain time. In this case, the paste plays the role of a component that erases microscopic irregularities, which is used when polishing various materials.

Salt and vinegar. For the manufacture of a cleaning composition, 25 mg of table salt is added to 100 ml of vinegar, stirred until completely dissolved and heated to a temperature of 60 ° C. The solution is sprayed with a spray gun on dirty places and rubbed with a soft cloth or sponge, after completion of work, the composition is washed off with hot water.

Soda and soap. Soda is poured into soapy water, the resulting solution is applied to contaminated places, after 20 minutes. the composition is washed off with hot water.

A mixture of ammonia and hydrogen peroxide. The liquids are mixed in a ratio of 2: 1 (50 g of hydrogen peroxide is poured into 100 g of ammonia), after which a sponge, a napkin are wetted with a solution and an acrylic bowl is wiped in contaminated places. Rust spots are usually removed in this way, and due to the fact that strong chemical components are used, it is necessary to work with rubber gloves. It should be noted that this method is the most effective among other home methods and is often recommended on the Internet.

Overview of Popular Bath Cleaners

To combat various types of pollution, it is more reliable and efficient to use household chemicals sold in the distribution network - they allow you to get a more pronounced effect than home-made solutions. The vast majority of products sold are designed to simultaneously get rid of traces of rust and limescale, so it is quite difficult to find an acrylic bath cleaner that removes only one of these contaminants.

In the market for the elimination of rust spots and hardness salts, the following brands are in good demand and have proven themselves well:

Bagi Acrylan- The products of the Israeli brand Bagi are always highly efficient in comparison with analogues, respectively, and the cost of Bagi is higher. Acrylan is supplied in a plastic container with a spray bottle; when cleaning, it is sprayed in the form of a thick foam - this allows the composition to adhere well to smooth vertical walls. Due to the high aggressiveness, the cleaning time takes no more than a minute; it is not necessary to use a sponge or a napkin when working.

In addition to lime and rusty streaks, foam decomposes dirt, soap stains, old stains, fungus and mold, renews the surface and gives it a gloss, and prevents further contamination. Bagi Acrylan contains surfactants, organic acids, stabilizers, solvents, 400 ml bottles are enough for 25 cleanings, the price of foam is from 350 rubles.

Meine Liebe- a trade brand of Germany, it includes non-ionic surfactants, sulfamic and phosphoric acids, trizodium alaninate. The drug is applied through a sprayer and forms foam on top, dissolves lime, rusty streaks, soap stains and dirt, after exposure to acrylic, a film is formed that stops subsequent pollution. It has a delicate effect on the surface and is well washed off with water, immediately after using Meine Liebe, bathing the child is allowed. The cost of 500 ml of the drug container is from 200 rubles.

Unicum Spray- it has a high concentration of surfactants, which contributes to the economical consumption of the spray, removes hardness salts, fungus, mold, rust stains, traces of soap. After application, it is well washed off, the nanolayer formed during spraying further prevents contamination. The cost of a container with a volume of 750 ml is from 300 rubles.

Sanfor Acrylight- designed to treat jacuzzis with hydromassage, steam cleaners, shower cabins, effectively removes old dirt, traces of soap and hardness salts. After use, creates a protective film that gives the surface a gloss and facilitates further care. Supplied in the form of a gel or spray foam, the cost of 920 g of a container with a gel is 120 rubles.

Cif Cream Active- a popular domestic-made cleaner for cleaning any surfaces from lime and traces of rust, microgranules in the composition allow you to cope with any difficult pollution. The cost of 500 ml of cream does not exceed 100 rubles.

Cilli Bang- the main component of the composition is hydrochloric acid, in the Cillit line there are universal reagents suitable for cleaning acrylic bathtubs. They do an excellent job with hardness salts, rust, stubborn dirt, stains. The cost of 750 ml capacity of Cillit bang spray is from 300 rubles, there are cheaper analogues for sale in 500 ml from 140 rubles.

comet- in the line of a well-advertised product, the Expert universal spray has recently appeared, designed to clean acrylic from lime and rust, which has antibacterial properties. The composition of Comet includes phosphoric and formic acids, the entire line has various aromas with a predominance of lemon, therefore, in addition to cleansing, Comet effectively eliminates odors. The cost of a container with a volume of 500 ml - from 140 rubles.

Chistin Sanitary- a mixture of acids of organic and inorganic origin is included in the composition of the domestic budget. Chistin effectively removes rust stains and hardness deposits, has antibacterial properties and fights odors. A 500 ml container can be purchased for 50 rubles, while Sanitary Chistin is not much inferior to more expensive and advertised counterparts.

The widely advertised Domestos gel for working under the toilet rim is popular with the consumer, many of its owners ask the question - is it possible to wash the acrylic bath with Domestos?

As can be seen from the above list of the best acrylic container maintenance products in the ratings, Domestos is not included in it and this is due to the presence of sodium hypochlorite in its composition, which is a strong oxidizing agent. Hypochlorite itself is 95.2% active chlorine, which is harmful to acrylic, therefore Domestos is contraindicated in acrylic bowls due to the high probability of damage to their surface during prolonged exposure.

Sometimes, during repair work, it gets on the bowl, for the removal of which chemical reagents are better suited - white spirit and acetone. In order not to risk it, it is safer to refuse chemistry when eliminating silicone - it is easily separated from the acrylic surface mechanically if any non-solid object is used for this purpose - a wooden or plastic plate, a rough cloth.

The plastic of the acrylic bowl is softer and therefore more susceptible to mechanical stress, and acrylic is also afraid of contact with certain chemicals in which it dissolves. These factors affect the care of an acrylic bath at home and the rules for its operation. Many users may find the following tips helpful:

• After washing, the bath is rinsed and wiped with a dry cloth - this prevents drips when water drops dry.
• Every week it is recommended to carry out a complete sanitization of the bowl and adjacent walls using an acrylic bath cleaner. You can wash the bathtub with any Fairy-type dishwashing detergent or a soapy sponge, then wipe it dry.
• Once every six months, the bowl should be disinfected, for this it is filled with water and a disinfectant composition (Ravak, Tim Profi) is added, the water is allowed to stand for 20 minutes. and then drained.
• Acrylic is easy to scratch, so it is not recommended to put basins, metal buckets in the bath.
• When bathing pets (dogs, cats), avoid contact of their claws with the bowl.
• With noticeable scratches and persistent stains that cannot be eliminated with chemistry, the damaged area is cleaned with fine sandpaper and then polished using special materials and pastes. Since polishing work requires professional skills, knowledge of technology and the availability of special devices (materials), it is better to entrust such operations to a specialist.
• With a long service life, the inner surface of acrylic bathtubs loses its gloss and becomes matte, while it gets dirty faster and more intensively, it is more difficult to care for it, and the procedure causes an increased consumption of cleaning gels and sprays. In this situation, you should think about polishing the entire surface of the bowl - this will improve the appearance, extend the service life and reduce the consumption of cleaning materials.

Unicum - instructions for use

When deciding how to wash an acrylic bath at home, they opt for folk cleaning methods or household chemicals, a wide range of which is sold in the distribution network. Of the self-made reagents, the mixture of ammonia and hydropyrite, recommended on many Internet portals, is considered the most effective.

Not always expensive and advertised cleaning compositions correspond in quality to their price, a good result can be achieved using domestic budget preparations (Cinderella, Chistin Sanitary), the cost of which is several times lower than known analogues.