Foamed roll insulation. Insulation in rolls, how to use it correctly and where? Types and characteristics of thermal insulation in rolls

During construction or repair, walls, ceilings, floors and other surfaces are covered with special materials, to prevent heat leakage during the cold period and did not bother the heat in the summer season. One of them is roll insulation, often used for large areas.

Advantages of roll material

This material has many advantages. The main thing is that the insulation in rolls does a good job of maintaining optimal temperatures indoors. There are other advantages:

The main types of insulation

Thermal insulation in twisted rolls can be used for both external and internal laying. There are options specially designed for pipes and communications. Rolled wall insulation is also available for sale directly under the wallpaper.

Raw materials for their production are also used differently. Thermal insulation from mineral components is the most common. Foamed polyethylene is also popular. Natural heaters like corks are less common and used. Some types have an additional layer in the form of foil or paper. Let's consider each option in more detail.

Special coating for thermal insulation

To improve the characteristics of their products, firms that produce rolled thermal insulation add certain coatings. The basis under them can be different.

Types of mineral wool in rolls

In this group of heaters there are several varieties. Their structure is the same, they differ in composition.

Any type of wool must be covered with a vapor barrier, especially in rooms with high humidity. And it also holds back the smallest particles of fibers that appear over time, negatively affecting a person. As part of the raw materials, formaldehydes are often used, which also affects health. Quality rolls should have a minimum of this substance

For laying mineral wool be sure to install the frame. On the walls, the panels with which it is held are pressed strongly so that the canvas does not move out over time. For the necessary protection from the cold, the number of layers can be increased.

Manufacturers often separate their products according to the purpose of the insulation. For ceilings and ceilings, the rolls will be lightened. For the main floor, walls, and other surfaces, the density of the material is usually increased. Due to this, the dimensions of the roll also change:

• length from 3 to 8 meters;
• thickness in 3 versions (50 mm, 100 mm, 150 mm);
• width from 0.6 m to 1.22 m.

Insulating wool manufacturers

Hardware stores offer a wide selection of mineral wool. Consider the features of the materials of some companies specializing in this area:

Has many positive qualities. It is obtained by filling heated polyethylene with gases. As a result, a mass is formed with many closed bubbles inside, which subsequently solidifies. For special strength, it is also “crosslinked”, i.e., the bonds of molecules are strengthened by chemical means.

Therefore, there are for sale two options: stitched and, respectively, not stitched. Both types have very low thermal conductivity, but the first one still has better characteristics, which is why it costs more (its density is 30 kg / m³). The general properties of materials are as follows:

The difference is that cross-linked polyethylene foam is able to absorb sounds well, but its fellow cannot boast of this. As a sound insulator, it works worse. Under mechanical action, the uncrosslinked version loses its shape irreversibly. The stitched one has a high compressive strength, which means it can be used for insulating horizontal surfaces.

Due to the thinness of the material, the length of the rolls can be up to 30 meters, the width is from 0.6 to 1.2 m. The thickness reaches 1 cm. . To fix the material on the wall, special glue is required.

Polyethylene foam brand Penofol

Insulation Penofol - appeared recently, but has already stood out among its own kind. It does not collapse from weather conditions and hostile environment. Heat insulators of this company have several varieties:

• foil coating can be fixed on one or both sides;
• rolls with an adhesive layer (simplifies installation even more);
• specialized type of isolation for communication networks;
• insulation for harsh conditions with a thickness of up to 40 mm.

Combined technology allows you to further reduce the thermal conductivity of insulated surfaces. Moisture-resistant and durable material that does not require vapor barrier costs can be used in various directions. Does not lose its properties in the temperature range from -60 to +100 С°.

Cork insulation for surfaces

An environmentally friendly and durable raw material for the production of thermal insulation is cork oak bark. Absolutely natural ingredients make the rolls safe for health. The crushed bark is connected with organic glue and pressed. The thickness ranges from 2 to 6 millimeters. The length of the roll reaches 10 meters, the width is mostly meter. Most often, in this form, the cork goes under the wallpaper, on the substrate for the laminate or "warm floor".

Thermal conductivity index not inferior to mineral wool, but the layer is used much thinner. Cork insulation is slightly flammable, poorly absorbs water and delays noise. However, its density is high, respectively, and the weight is large. The margin of safety is high, the service life is declared up to 50 years. The negative side is the price of "naturalness", compared to the rest, it is quite high.

This insulation is produced mainly by Portuguese companies: Wicanders, Izora, Amorim. They offer a wide range of insulation rolls, which can also serve as wall decoration. Installation is also simple, basically the cork is “planted” on glue.

Modern technologies provide a huge selection of heat insulators for any premises and structures. The selection criteria are based on which surface needs to be covered and how much the buyer is willing to pay for it in order to maintain comfort in their home.

How do you look at the prospect of reducing home heating costs by almost a third? We think this is the case when comments are unnecessary. To achieve such a result is real, it is enough just to choose the right thermal insulation for the roof.

One of the most common heat-insulating materials is mineral wool, in particular, in the form of mats. However, when it is necessary to insulate, for example, large areas, such a solution is ineffective. For such cases, roll insulation will do more.

All materials of this type have approximately the same advantages, which explains their high demand. These are qualities such as

• low thermal conductivity
• good soundproofing,
• optimum hygroscopicity,
• high water repellency,
• chemical resistance,
• fire safety.

And this is not the whole list.

Roll insulation, due to its elasticity and flexibility, easily restores its shape, suitable for work on uneven surfaces. It does not have any temperature restrictions, as it retains its performance characteristics at extreme temperatures.

Scope of insulation in rolls

It is successfully used for roofs and basements, floors and ceilings, pipes and more. The device of thermal insulation from this material is a fairly simple process. Moreover, the work can be done independently, without the involvement of additional labor. Therefore, this type of thermal insulation has gained great popularity in private construction, in particular, baths, outbuildings, etc.

Types of insulation

In a separate group, materials with a protective layer of foil are distinguished. At a cost, they are somewhat more expensive than the others, but at the same time they have many additional valuable properties.

The foil itself does not have the thermal conductivity necessary for the insulation, however, it effectively retains heat due to the ability of the reflective surface to block infrared rays from the room. It is worth noting that at the same time it does not allow their penetration from the outside. The latter is a rather useful quality for roofing insulation, especially in hot summers, when the roof warms up very much under the influence of sunlight.

Insulation roll foil allows you to provide the maximum length of the material, that is, it is laid from one whole strip, which is extremely important for its effectiveness. . These include foamed rubber, polyethylene and other rolled materials.

These materials do not hold their shape and are easily rolled into rolls. They are quite efficient and easy to work with. Unlike foil insulation, they are used in combination with vapor barrier, which creates the perfect tandem against the cold.

These include foamed rubber, polyethylene and other rolled materials. These materials do not hold their shape and are easily rolled into rolls. They are quite efficient and easy to work with. Unlike foil insulation, they are used in combination with vapor barrier, which creates the perfect tandem against the cold.

This is the most common type of isolation. This form of packaging is considered by many to be optimal, since with this approach, long strips of insulator take up a small volume. Most often, floor beams or mounting profiles are installed in increments equal to the width of the roll. This greatly simplifies installation: firstly, the materials are simply spread over the surface and fixed, and secondly, no extra seams are formed.

Overview of manufacturers: Izover, Knauf, Ursa

How to choose the right roof insulation How to choose a roll insulation. Varieties of roll insulation. What are the advantages of rolled foil insulation. Roll characteristics

Popular manufacturers

There are products from various manufacturers on the market. Each brand has its own features and benefits.

Knauf

The German manufacturer offers a material that does not contain formaldehyde. Knauf products are safe for people. Mineral wool does not cause allergies, but it should be laid with gloves. The microscopic fragments that make up the insulation can cause skin irritation.

Roll materials Knauf are not interested in insects and rodents. In addition, they are able to protect against external noise due to good soundproofing characteristics. They are characterized by low thermal conductivity and good air permeability. The company offers materials for the protection of walls, slabs, pipes and other surfaces in cottages and country houses.

Isover

Insulation with high density. The French manufacturer offers products of various thicknesses: from 20 to 150 mm, which significantly expands the possible area of ​​\u200b\u200buse of Isover insulation.

The company's catalog contains heat-insulating material with foil, which is often used to insulate pitched roofs, walls, ceilings, and install underfloor heating not only in houses, but also in baths and saunas. In terms of flammability, it corresponds to the first class.

ursa

High-quality professional insulation with a long service life. It has excellent soundproofing characteristics. Does not burn. Under the influence of a flame does not emit toxic substances. During installation, it does not break, does not crumble. Pleasant to the touch.

When insulating the walls of private houses, M-11 is most often used. When performing thermal insulation work in the industrial complex, preference is given to P-30.

Topizol

The insulation can have a thickness of 3 - 20 mm. Suitable for various climatic zones, including regions with high humidity. Doesn't rot. Differs in good vapor permeability. With sufficient tightness of the seams, it is able to withstand gusts of wind.

It is used to protect walls, roofs, including mansard floors. Differs in small weight that facilitates transportation and reduces requirements to strength characteristics of the warmed surface. Able to maintain its performance characteristics for at least 30 years.

Installation can be done independently without special equipment.

Penofol

Multilayer foil material, there are several types. Type A provides for a single foil layer. Type B has self-extinguishing polyethylene between layers of high quality aluminum foil. Type C comes with a special adhesive base, which greatly simplifies its installation. Type A has the lowest cost and least rigidity.

The thickness of the foil at Penofol is 12 - 30 microns with a base thickness of 2 - 10 mm. For insulation of surfaces operating in fairly harsh conditions, material up to 40 mm thick can be used.

Eco-friendly, safe, suitable for warming children's rooms.

Scope of roll insulation

Rolled heaters are used for thermal insulation of vertical and horizontal surfaces. Foil material is indispensable for creating thermal insulation in bath rooms, because it retains heat well and has heat-reflecting properties. And also this material has found wide application for thermal insulation of individual structures, joints, in hard-to-reach places.

Consider the main ways to use rolled heat insulators.

Rolled heat insulator for walls

Roll insulation for walls can be used as a heat-insulating material applied under decorative finishes, including wallpaper.

The application technology is very simple:

• self-adhesive material is glued to a wall prepared in advance, leveled and cleaned of debris and old finishes;
• a cement-based adhesive is applied to the heat insulator layer, resembling liquid plaster in properties;
• after the adhesive has hardened, you can start gluing the wallpaper.

The use of such material under the wallpaper will significantly increase the heat-preserving properties of the walls, as well as their sound insulation.

Roll heat insulator for the floor

It is used as a substrate for various types of decorative floor coverings. It has not only heat-insulating properties, but also gives the floor "softness", eliminates squeaks and sounds during shrinkage and movement of the floor covering.

In some cases, a foil heat insulator can be used to insulate the floor, this will increase heat retention, however, the cost of materials reinforced with foil is 30-60% more expensive.

The technology for the production of floor insulation using foamed polymer in rolls is very simple:

• the material is glued to a wooden floor or concrete screed using an adhesive composition or self-adhesive properties;
• leveled so that there were no "bubbles";
• the floor covering is laid on top.

The advantages of such a heat insulator include ease of installation, no debris, durability and environmental safety. When choosing a rolled heat insulator for the floor, it is worth remembering that the “softer” the floor covering, the denser the insulation should be.

In other words, it is better to use a polymer with maximum density under linoleum, otherwise, when walking, you will “sink” in the floor covering, but under a laminate or parquet, you can lay a polymer with any density.

Roof insulation roll

Suitable for thermal insulation of pitched and flat roofs. A roof insulated with such material will be warm for several decades. You can lay thermal insulation on your own, without involving highly paid specialists. The heat insulator is located between the elements of the roof truss system, while distortions, the formation of waves and other defects are not allowed.

In some cases, for example, when insulating a residential attic room or in regions with a cold climate, it is recommended to lay the insulation polymer in two layers.

The technology of work on the installation of thermal insulation of the roof depends on the design features. The best option is when thermal insulation is calculated at the design stage. In this case, the work boils down to the fact that the rolled material is rolled out and glued to the inner surface of the roof, a layer of vapor barrier material is laid on top and the final finish is arranged, for example, siding, lining, etc.

Application of rolled insulation

This technology is far from perfect and creates only the illusion of real savings in material resources, since in fact this type of insulation is inferior in all respects to such sprayed counterparts as polyurea

Another difficulty is the application technology. It should be mentioned right away that all surfaces must be prepared: thoroughly cleaned or even washed. Even minor pollution can lead to negative consequences. Self-adhesive insulation is applied similar to adhesive tape, but the effectiveness of this method is lower. Over time, the adhesive loses its properties, especially under the influence of temperature changes, and the material peels off. Fused insulation is applied using a gas burner. It's a slow and painstaking process, but the grip is somewhat better, although there's no guarantee that it won't slack in some places.

Regardless of whether roll waterproofing of the floor or any other surfaces will be carried out, this process takes a lot of time and effort. Accordingly, the term for putting the object into operation is delayed. And yes, this work is expensive. Therefore, this technology is far from perfect and creates only the illusion of real savings in material resources, since in fact this type of insulation is inferior in all respects to such sprayed counterparts as polyurea.

Advantages and disadvantages

The main advantages of roll material are:

• Versatility. Suitable for thermal insulation of any surfaces. For complex spatial shapes, including curvilinear, a suitable piece can be cut.
• Minimum requirements for surface preparation prior to laying.
• Benefit in terms of material price and work productivity when insulating large wall areas, especially straight sections.

They have rolled materials and disadvantages.

• High labor intensity when laying in a frequent crate, additional time is required for cutting.
• Low rigidity does not allow them to be used where it is required to withstand significant loads.

In general, the advantages compensate for the disadvantages, which explains the high popularity of roll materials among consumers.

Materials are harmless to health, provided they are used correctly and fire-fighting regime is observed.

Varieties of roll insulation

Mineral wool

Available in several modifications. A common disadvantage is hygroscopicity. All heaters must be protected from direct contact with liquids; the difference between them is only in the intensity of its absorption.

• Glass wool. Pros: one of the cheapest (made from glass "battle" that has been remelted), unattractive to rodents, insects (often used in the arrangement of warm floors). Increased density, the ability to dampen sounds, non-combustibility add glass wool advantages in use. Minus the complexity of working with the material. When installing a rolled heat insulator based on glass wool, you cannot do without protective equipment. And not only the respiratory organs, vision; tight, closed clothing is needed - microscopic fractions of glass penetrate literally everywhere.
• Slag. It is also based on waste, but the metallurgical industry. In terms of cost, this insulation is comparable to glass wool (even somewhat cheaper), but loses in terms of resistance to high temperatures. But in terms of thermal conductivity - the leader among mineral wool. For all other characteristics, it is approximately on the same level with other heaters of this group. Cons: absorbs moisture (increased hygroscopicity), dampens noise poorly.

There is another drawback that makes the use of slag wool for the insulation of metal pipes impractical. It is not recommended to use it for thermal insulation due to residual acidity - it acts destructively on steel.

Basalt wool. The raw materials are processed rocks. Pros: the ability to withstand high temperatures (up to +700), the optimal combination of thermal conductivity / density characteristics. The peculiarity of the material is that after getting wet it does not lose its heat-insulating properties (although there is a limit to the percentage of humidity), it has a high sound absorption, is fire-resistant, “environmentally friendly” (safe for allergy sufferers).

There are few cons: this insulation needs high-quality vapor barrier, it becomes caked over time.

Any of the listed thermal insulation materials is also sold in the "foil" modification. The thinnest layer of aluminum increases the heat-reflecting properties of the product, protects it from contact with moisture.

Polymers

All roll heat insulators are made on the basis of foamed polyethylene or polypropylene. They differ in characteristics, but given the small thickness of the sheets, the difference in thermal conductivity between them does not really matter, so they can be considered identical. The most advertised, although not the only representatives of this group of elastic heaters on the market: Penofol (PE) and Penotherm (PP).

Russian products under the brands Energoflex, Energofloor, Jermaflex (combined material) from ROLS ISOMARKET are characterized by good reviews. It is relatively new on the market, but judging by the exchange of opinions on the Internet, it has perfectly established itself as an effective and versatile insulation. Its quality was also appreciated by specialists.

The main role is assigned to the metallized layer. It is the foil that prevents the passage of heat rays through the material. The heat insulator is covered with it on one or both sides; the choice of option is determined by the conditions of application.

Choosing a heater of an unknown brand, you may encounter a substitution of concepts. To reduce the cost, individual manufacturers instead of a foil layer apply metallized spraying to the thermal insulation. Such a screen does not differ in durability, and in terms of efficiency it is significantly inferior to the aluminum coating.

So which option is better to choose cotton wool or polyethylene foam

The main point that is important to understand is that foamed polyethylene or polypropylene in the form of rolls is exactly thermal insulation, that is, a material whose purpose is to slightly improve the characteristics of the walls, and not fully insulate them. No matter where it will be fixed - from the inside or from the front

But basalt wool is already a real insulating layer. True, in the case of indoor use, the wall will still freeze through, just noticeably less heat will come out of the room.

It turns out that from the inside, polypropylene will give a lesser effect than cotton wool, since the temperature will rise only by a degree and a half. And even if you perform outdoor installation, then the “picture” will be the same, but with only one positive moment - the wall will freeze a little less and the condensate from the side of the room will disappear.

At the same time, the material has an undeniable advantage - it is cheap and it is very easy to mount it. It is more difficult and expensive to work with cotton wool, since it will be necessary to make a false wall (usually drywall) to protect the basalt fibers, and besides, it is important to take care that moisture does not get into the structure of the material. If this happens, then the effect of all the work done will be zero, since all thermal insulation qualities will disappear very quickly.

Here it seems to start to seem that cotton wool is better anyway (because it is “warmer”), but everything is decided by the nuances of the situation. Yes, cotton wool seems to be good, but what's the point in it if, for example, you need to insulate the shower room not in the house, but, for example, in the country and you don’t want to invest? The obvious budget solution in this case is a metallized insulator - stick it on the wall and forget it.

But in the case of a more or less capital approach, but again in the absence of significant financial resources, it is better to opt for mineral wool and insulation from the inside. It turns out that there is no ideal option and a decision needs to be made only based on the characteristics of the project.

Manufacturers of heat insulators and their products

The greatest demand from the consumer is used by rolled insulation from several manufacturers.

Knauf is a German brand whose products do not contain formaldehyde, which gives the finished product absolute safety and harmlessness, which is relevant during installation work.

Isolation from Knauf

Rodents and insects do not start in such heaters, they have a wide assortment range, a long service life and the possibility of using not only apartments, but also country houses (cottages) for insulation.

Isover is a French manufacturer offering a wide range of roll insulation with excellent performance, including foil-coated. The products are suitable for carrying out thermal insulation measures both indoors and outdoors, it is not subject to combustion and is able to die out in case of fire.

Insulation for outdoor and indoor work

URSA - Spanish heaters under this brand are characterized by a long period of operation with full preservation of the main technical parameters. The manufacturer guarantees the highest quality of its products and its effectiveness in both private and industrial construction.

TechnoNIKOL is a Russian manufacturer offering high quality products at very affordable and affordable prices. These roll heaters are produced on the latest equipment using innovative technologies and techniques, which makes it possible to guarantee not only quality, but also a long service life.

Classes and types of roll waterproofing

Produced roofing waterproofing, depending on the purpose, quality, components used and price category, are divided into several classes.

Material class	Name	Price range	Characteristics	Purpose
Premium	Technoelast	100-160 rubles/m2 For models with a noise-absorbing effect - the price is up to 250 rubles/sq.m.	Built-up coating with application of bitumen and SBS-modifier. It is used at a temperature from-50 to +1000C.	The lower / upper layers of the roof, underground utilities.
Technoelastmost	235-250 rubles/sq.m.	The canvas is 5-5.2 mm thick, the level of heat resistance is up to + 1000C. Filler - bitumen with artificial rubber (SBS). High-strength coating, service life - up to 40 years.	Waterproofing of reinforced concrete slabs on the carriageway of roads or in the form of an adhesive layer on the spans of bridge structures.
Business	Uniflex	85-130 rubles per square meter, depending on the thickness and type of base.	Welded coating with SBS-modified bitumen filler. Damage resistant, durable. The expert period between repairs is at least 18 years. The flexibility of the material is maintained at temperatures up to -200C.	Laying of the upper and lower layers of the roof, repair roofing, waterproofing of the foundation, basements, basement floors.
Standard	bipol	70-90 rub./sq.m.	Welding material, binder layer 1.5 mm thick. Withstands temperatures from -150C to +850C. The top layer of the coating is slate chips. Service life - 5 years.	It is used as the first layer of roofing or for the top of the roof. Repair of the roof of the housing stock.
Bicroelast	67-84 rub/sq.m.	Welding material based on fiberglass, fiberglass or polyester. Protective coating - slate powder or film. Thickness 3-4 mm, remains flexible at -100C.	It is used as a lining material for arranging roofs, waterproofing structures of various types - buildings, tunnels, bridges. Variety "K" is used to cover the top layer of the roof.
Economy	Bikrost	55-85 rubles/sq.m.	Built-up coating, with bituminous filler. Flexibility is maintained only at positive temperatures, heat resistance - up to + 800C. Thickness 3-4 mm, service life - up to 10 years.	Waterproofing, installation of the lower / upper layer of the roof - depending on the coating.
Euroruberoid P	13-16 rubles/sq.m.	Coating based on fiberglass, with the application of modified bitumen. A protective coating is applied to both sides of the insulating sheet. The thickness of the protective layer is 2-5 kg/sq.m.	Waterproofing of building structures, arrangement and repair of roofing carpet in buildings.

The building materials market represents a wide range of models of rolled waterproofing coatings - both universal and designed for a specific type of work.

Characteristics

For heat-insulating material in rolls, released under various brands, common characteristics are characteristic.

Environmental friendliness

The insulation meets the regulatory requirements for environmental safety.

As a rule, it contains salts of heavy metals, alkalis, acids, oxides, phenols or toxic organic compounds that are inactive at room temperature, are present in a minimal amount.

Due to the low chemical activity, thermal insulation practically does not interact with aggressive media, and therefore, for example, is not afraid of solvent exposure.

Biological stability and fire safety

The material has a high level of biological stability. As a result, it does not contain rodents, fungus, mold. For insects and animals as food, it is uninteresting. Depending on the composition and other characteristics, the insulation is able to withstand exposure to high temperatures.

Air and vapor permeability

If the insulation is used to insulate the floor or walls, breathability is an important indicator.

When using rolled materials, you can not be afraid of excessive dampness in the room, the formation of condensate and other negative phenomena, provided that the installation is done correctly.

When going shopping, it is worth remembering the following aspects of the choice:

1. For indoor and outdoor use, various variations of insulation are suitable.
2. The surface that will be covered with rolled thermal insulation also matters. There is a fundamental difference between the materials used to insulate the ceiling and walls. Each of these bases has its own insulation.
3. It is also important to remember what material the walls are made of. A heat insulator for a wooden base may not be suitable for a concrete base and vice versa.
4. When choosing the thickness of the material, it is worth taking into account the temperature conditions in the winter and the climate for a particular region.
5. Before purchasing, it is imperative to familiarize yourself with the quality certificates and other permits for the selected roll insulation, and in addition, make sure that the packaging is intact. Moisture, even in small quantities, can adversely affect the design parameters of the material and its properties.

Choose quality material from trusted manufacturers

Heaters in rolls are presented on the market in a wide range. Each of them has its own characteristics, has positive and negative characteristics. The choice of a particular option is up to the user, but if there are difficulties, you should not rely on chance. It is better to seek help from professionals and save your nerves and money.

3 Roll foil thermal insulation

The rolled foil insulation presented on the market, as a rule, is made either on the basis of polyethylene foam (quite a popular brand "Penofol"), or on the basis of polypropylene ("Penoterm").

These are two materials almost identical to each other, the difference between which lies only in the physical and mechanical characteristics. If we consider only those that affect the direct efficiency of use as a heat-insulating material, then foil roll insulation for walls based on polypropylene looks more preferable.

So, the polypropylene base has an order of magnitude lower thermal conductivity (a difference of about 30%), less moisture absorption and better resistance to external mechanical influences.

In fact, the last factor can be neglected, since the foil insulation itself, due to its minimum thickness, does not provide effective insulation if the foil is damaged, so it is important to look at the quality of the foil coating. .

Roll foam with one-sided foiling

Unscrupulous manufacturers, in order to reduce the cost of production, can use not aluminum foil as a shielding layer, as required by the technology, but ordinary metal spraying.

The effectiveness of such spraying is much lower than that of foil, while the cost of such products sold under the guise of high-quality insulation is comparable to high-quality products from trusted manufacturers. When choosing foil-covered insulation for walls, floors, or pipes, carefully check the quality of the shielding layer.

High-quality foil thermal insulation has the following advantages:

• High heat shielding ratio, about 97%;
• Wide functionality - foil materials are used not only for household insulation of walls, floors and ceilings, they are also widely in demand for thermal insulation of all kinds of industrial equipment;
• Minimum roll weight;
• Ease of installation - foil thermal insulation does not require frames, anchoring and similar frills, it sits on the wall on mounting foam, or ordinary building glue;
• Minimum cost - the price of foil materials is much lower than that of mineral wool;
• Complete vapor barrier;
• Safety for the human body.

Foil insulation has only one significant drawback - it is prone to burning. The operating temperature of polypropylene is 150 degrees, polyethylene foam is 80 degrees.

3.1 Features of thermal insulation of the balcony with foil roll insulation (video)

Characteristics

Roll insulation materials are characterized by the following main parameters:

• Environmental friendliness. All models on the market must comply with building safety requirements for installation, operation and disposal. They must contain small amounts of harmful substances, these substances must not be released from the insulation during its storage, installation and during use. The packaging indicates the method of disposal. The materials are resistant to organic solvents and other active substances.
• Fire and biosecurity. Mineral insulation does not burn itself and prevents the spread of flame. Foam materials are able to withstand fire for a certain time. Materials prevent mold and repel rodents.

• Air and vapor permeability. Key characteristics. They show how much air or water vapor at a certain temperature can seep through a unit area of ​​the material. Vapor permeability is necessary in order to remove excess dampness from the room to the outside through the walls and their ventilation systems.
• Strength. An important characteristic of insulation for wallpaper. Touching, including with hard objects, should not damage the wallpaper.

What roll insulation to buy

Roll insulationis the name of a whole class of lightweight thermal insulation widely used in civil and industrial construction. They are made from staple fiberglass with the addition of various binders, fillers, water repellents (substances that repel water), which give them softness, elasticity and resilience. Roll thermal insulation is the most inexpensive of all types of insulation, therefore it is in consistently high demand among builders.

This section of the site presents roll insulation, their price and roll parameters. All information about products from different manufacturers is given on one page. Here you will find a brief description of each of them.

• ROLL INSULATION URSA

This is a very well-known line of heaters from a European manufacturer - the URALITA concern. Roll insulation brand URSA are soft elastic mats made of staple fiberglass. Each brand has its own marking, which allows buyers to easily navigate the characteristics of the material and, accordingly, its purpose. URSA heaters are high-quality lightweight heaters recommended for use in horizontal unloaded building structures. Good thermal performance, ease of transportation and installation make them the most popular for many years.

A special place in the line of rolled heaters of the URSA Concern is occupied by new generation heaters under the URSA PUREONE trademark (in rolls and plates). Acrylic, a neutral and safe polymer, is used here as a binder. The production technology of these heaters eliminates the use of phenols and formaldehydes, which makes them particularly environmentally friendly. They are widely used in Europe, America, Japan for heat and sound insulation indoors. In Russia, they also gained well-deserved popularity.

• ROLL INSULATION KNAUF

These are natural mineral wool insulations made on the basis of innovative ECOSE technology. In the manufacturing process, binders based on natural ingredients are used, therefore it has a pleasant color of natural linen, and a texture that is pleasant to the touch. Due to environmental friendliness, such heaters can be used indoors.

You can always contact our specialists who will tell you where you can find additional information about the insulation you are interested in or give advice on how to install the material.

Mounting technology

The installation technology of rolled insulation is slightly different from plates. They begin to insulate the walls or floor initially. The walls are mostly made of slabs, as is the straight ceiling. Therefore, often, the floor and pitched ceiling-walls are suitable for insulation and installation. When insulating the floor, it is worth looking at what type of insulation is available.

Insulation is mainly used in foil, but sometimes insulation rolls are covered with ordinary heat-insulating foil or metal film. The insulation should move away from the walls by 1 cm. This is due to the fact that with temperature changes the material contracts and expands. The lack of free space in a metallized or foil insulation leads to its deformation and damage over time.

Ceiling (pitched) heaters are fixed between the rafters, cutting out a little more to insert better between the boards. Insert them strictly from the bottom up to avoid voids. After installation, the surfaces are clamped with main profiles or boards for applying additional (for example, vapor barrier) materials from above. The work is carried out very carefully.

Let's move on to the installation of walls with a roll type of insulation from the inside. It is produced by preparing the walls for pasting. Dilute a special glue for cotton wool, the wall should not be putty or plaster, only bare concrete or brick is allowed. The composition is applied to the wall evenly under a special comb, after which they start gluing the rolls, which can be cut for convenience.

At the same time, it is desirable to make the wall itself in a level, plane, if there are no further plans for sewing into a box or gluing glass wallpaper. After the material is mounted on the wall, it is necessary to screw it in. Each petal should be slightly recessed in the cotton wool. At least 5 fixing holes are required per 1 m2. It is better to fasten the sheets themselves and the space between them (in this case, both sheets will grab, which will avoid warping, bring out the level and plane).

After the sheets have set, a layer of glue should be applied. The technology resembles puttying, only with a different solution

It is important to monitor the level and plane. It is necessary to make at least two passes, since it will be problematic to put a good layer the first time

After leveling, regardless of the type of room, you can proceed to the next work. When installing drywall sheets inside the house, they are fixed with dowels to the thermal insulation layer, which is desirable to be treated with glue, as in the previous paragraph.

About the advantages of URSA roll insulation, see the video below.

Operational Imperfections and Maintenance Difficulties

Each type of waterproofing material has its own unique characteristics. So, technonicol, which, according to the manufacturer, can withstand high mechanical loads, may not withstand increased soil mobility. Therefore, many use a modification for waterproofing road substrates from the same manufacturer. But these are unjustified costs.

With regard to maintenance, for example, in the event of damage to the polyurea coating, it is enough to simply spray a small layer on this place locally. But rolled waterproofing, which has peeled off in some place, requires serious repairs. It is necessary to remove it, at least in this place, prepare the base, reapply insulation, blocking the formed seams. Of course, there is no question of any aesthetics, and the quality of such a patch will be far from perfect.

Waterproofing with roll materials is not universal. So, with their help it is impossible to process surfaces of complex shapes, for example, the bottom of a car. And even roof waterproofing can be a serious problem. In addition, high temperatures adversely affect this material and the degree of its adhesion to the base.

The main disadvantages of waterproofing with roll materials in specific conditions:

• Rolled roof waterproofing – the impossibility of processing surfaces of complex shapes, a long application process, exposure to the negative effects of temperature changes, the complexity of maintenance
• Rolled floor waterproofing – poor perception of constant mechanical loads, especially in vibrational conditions
• Roll foundation waterproofing - instability to the negative impact of moving soils, additional load on the foundation, which is undesirable in areas with high groundwater levels and in loose soil bases

Characteristics of basalt wool

If the insulation under the roll wallpaper, which was discussed above, does not suit you, then you can choose basalt or fiberglass wool, which has a wide application potential. It can be installed on walls or floors, as well as on ceiling spans. It is not recommended to use this material for sloping roofs, this is due to the fact that over time, the massif slides, and the insulation density is broken. If you want to use this floor, then you need to lay at least two layers. This will allow you to get 1 decimeter of thickness. If there is a need to insulate the walls, then half the amount should be used, while laying the material in one layer will be enough. If you want to achieve the arrangement of an effective heat-saving screen, then you should use a similar thermal insulation with vapor and waterproofing.

What to consider when working

Insulation with mineral roll materials can be carried out at any time of the year, it is only important to protect the material from precipitation. . The use of foam materials mounted on an adhesive layer depends on the air temperature

Usually limited to -10C. Special adhesives are also produced, effective up to -20C.

The use of foam materials mounted on an adhesive layer depends on the air temperature. Usually limited to -10C. Special adhesives are also produced, effective up to -20C.

Before the start of insulation, a minimum surface preparation is required:

• Dismantle pipes, electrical wiring, lamps, decorations, plants, etc.
• Clean the walls from the remnants of old coatings, debris and dust.
• Install a crate for mineral insulation.
• Level and clean the surface for gluing foamed thermal insulators.

Installation does not require special equipment, from the tools you will need:

• construction knife;
• stapler;
• screwdriver;
• a hammer;
• double sided tape.

It is more convenient to carry out installation and cutting of rolled heaters together, especially with large amounts of work. Small volumes are within the power of one master.

Warming process

The sequence of operations for the installation of mineral heaters is as follows

• A vapor barrier film is attached to the prepared wall.
• A crate is mounted from wooden bars or metal profiles. The recommended guide pitch is 50 or 60 cm.
• Rolls are cut according to the selected pitch. Cutting should be carried out so that the insulation enters between the guides tightly and, straightening out, provides a better fit to the guide.

Dowel dowel

• Mineral wool is attached to the wall with plate-shaped plastic dowels, cut according to the thickness of the layer at the rate of 4-5 per square meter.
• The windproof film is attached to the guides over the laid wool. The joints of the film are sealed with double-sided tape. Installation of insulation on the walls of the house.
  Scheme of installation under the crate

  Thermal insulation completed. You can proceed to the installation of the selected cladding - wood or vinyl siding. To ensure the ventilation of the facade, a secondary lathing of thin laths is installed on top of the wind insulation.

  Scheme of installation under plaster

  Read on the topic -.

  Installation of rolled foam insulation for external and internal walls is simpler in itself, but requires better surface preparation. It will have to be leveled more carefully - the foam will not be able to conceal irregularities as much as mineral wool.

  It is not recommended to fasten foam rolls with a construction stapler - the staples create so-called thermal bridges through which cold can penetrate into the warm part of the room. The heat-insulating effect of the material is somewhat reduced.

  How to fix the insulation on the wall:

  • Clean and level the wall surface.
  • Cut the material for butt jointing.
  • In places of complex spatial shape - near openings, in corners, adjoining building structures (beams, balconies, etc.), it is better to try on cut pieces before applying glue or removing the protective layer.
  • Apply glue to the heat insulator or remove the protective film from the adhesive layer.
  • Glue the material, moving from the bottom to the top.
  • Smooth the surface with your hands or a rule, achieving the best fit. If small air bubbles have formed, they should be carefully pierced in the center with a sharp needle and, moving from the edges of the bubble to the hole, squeeze out the air.

  After half an hour, the glue will set and the heat-insulating layer will be ready for use. When installing the cork sheet, an adhesive specially designed for cork is used. It is applied both to the wall and to the cork. Before sticking the wallpaper, you should wait until the glue is completely dry to avoid warping.

2 Roll thermal insulation based on mineral wool

The quality of this category of insulation is regulated in accordance with the requirements of GOST RF "52953-2008". This quality standard allows the following heat-insulating material to be classified as mineral wool insulation:

• Basalt wool is a material produced by remelting rocks and the subsequent formation of microscopic fibers from them, connecting into a solid carpet;
• Slag wool is a material made from waste from the metallurgical industry. As a rule, it costs much less than basalt wool;
• Glass wool is obsolete, but still quite often used due to its low price material. Produced by melting cullet.

Rolled basalt wool has a characteristic yellow tint

Roll insulation based on mineral wool, due to its elasticity and flexibility, is an extremely versatile material that can be successfully used both for thermal insulation of walls, floors, attics, and other flat surfaces, and for thermal insulation of pipes.

2.1 Mineral wool production

Consider the technology for the manufacture of mineral wool using the example of basalt insulation. Rock basalt rocks, the chemical composition of which meets the requirements of GOST, can be melted down in two ways - hot and cold.

The hot method involves heating basalt rocks in blast furnaces, the cold method involves exposure to electromagnetic radiation (according to the principle of a conventional microwave).

The molten rock is fed into a centrifuge, which is equipped with permanently cooled carbide discs. Under pressure, molten basalt is fed into a centrifuge and falls onto rotating disks, where, in the process of carved cooling and pressure drop, individual basalt fibers are formed from the melt.

The resulting fibers are immediately removed from the drum by a special functional element and fed through the conveyor to the laying machine, which forms a carpet of basalt wool of the required thickness.

After laying the carpet, the fibers are impregnated with a variety of impurities that are necessary to give the final product the required characteristics - hydrophobicity, fire resistance, density and elasticity.

Slag, as a rule, has a darkish tint

2.2 Advantages and disadvantages

Among all the thermal insulation materials on the market in the middle price category, it is mineral wool that has the lowest thermal conductivity. Although the leaders in general are polystyrene and mineral wool.

An important factor is that the thermal insulation properties of mineral wool do not depend on any external conditions in any way - this material does not expand under the influence of moisture, does not undergo thermal expansion, microorganisms and rodents do not start in mineral wool.

Rolled mineral wool insulation is produced with a wide variety of performance characteristics - you can choose both low-density mineral wool for insulating pipes and other uneven products, and dense material for thermal insulation of surfaces experiencing external loads - floors or attic floors.

An important advantage of mineral wool is its fire resistance. This material can withstand temperatures up to 700 degrees, it does not light up even under the direct influence of fire. It is also worth noting good noise-reducing properties - by insulating the walls and floor with rolled mineral wool, you will solve not only the issue of insulation, but also the sound insulation of the house.

The only drawback of mineral wool is the high vapor conductivity, due to which the installation of this insulation requires the installation of a special vapor barrier film.

Thermal insulation of the pipeline using rolled glass wool

Roll insulation based on mineral wool can be used for the following purposes:

• Insulation of roofs, floors, walls, and any flat surfaces;
• Thermal insulation of pipes and pipelines;
• Thermal insulation of industrial equipment;
• Warming element inside the sandwich panels (here is the best thermal insulation Hitrock);
• Internal insulation in false walls and when laying hollow walls;
• External insulation of the walls of the house, followed by plastering.

The ROVEN company offers to buy rockwool pipe and roll thermal insulation in Sevastopol at a bargain price. We invite you to visit our office at: Sevastopol, Fiolentovskoe highway, 1/2, letter L, office 105 (the territory of the Mayak plant). Call the phone +7 978 117 57 03 , our experts will answer all your questions.

Cylinders plain and laminated mineral wool on a synthetic binder Rockwool cylinders - pipe insulation, which is a hollow product made of stone wool of the basalt group (simple). Rockwool cylinders can also be produced with aluminum coating (laminated).

1. Rockwool pipe and roll insulation
2. Roll insulation: types and features of roll insulation
   1. Thermal insulation based on roll insulation
   2. Advantages of thermal insulation in rolls
   3. Types and characteristics of thermal insulation in rolls
   4. Heat insulator with a foil surface: features
   5. Tips for choosing thermal insulation in rolls: what you need to know
3. Overview of the characteristics of insulation in rolls
4. How to choose the right roof insulation
   1. Scope of insulation in rolls
   2. Types of insulation
   3. Overview of manufacturers: Izover, Knauf, Ursa
5. Roll insulation
   1. Scope of roll insulation
   2. Heat-insulating roll materials from mineral wool
   3. Roll insulation Penofol

• Low thermal conductivity and high thermal insulation properties
• High biostability and chemical resistance (to solvents, oils, acids and alkalis)
• Extended operating temperature range (melting above 1000°C)
• High temperature does not affect the thermal insulation properties of the material
• There is a longitudinal cut for ease of installation, easy to cut with cutting tools

Specifications of Rockwool pipe insulation

λ125 = 0.048 W/(m K)

λ300 = 0.087 W/(m K)

Flammability group Rockwool

NG, foil-coated - G1

Rockwool application temperature

from -180 to +650 °С

Acidity modulus, not less than Rockwool

Roll thermal insulation

WIRED MAT 80 is made from stone wool based on basalt rocks. One side of the mat is covered with a 25 mm mesh made of galvanized or stainless wire. In addition, the mat is stitched with galvanized or stainless steel wire (SST). The product is also available with aluminum foil on one side (ALU WIRED MAT 80).

TEX MAT - light hydrophobized mats on a synthetic binder, made of stone wool based on basalt rocks. On one side, the mats can be laminated with aluminum foil.

Application:

WIRED MAT 80 is used for thermal insulation of technological and power equipment, heating networks, main and industrial pipelines with temperatures up to 750°C.

ALU WIRED MAT 80 is used for fire protection of air ducts.

TECH MAT is used for thermal insulation of pipelines and industrial equipment. The maximum application temperature is +570°С.

Rockwool pipe and roll insulation ROVEN offers favorable prices for rockwool pipe and roll insulation in Sevastopol. Description, technical characteristics, photo.

Symbols for grades of rolled waterproofing

In addition to the name of the waterproofing material model, there are letter markings in the name. Each of the letters denotes a specific feature inherent in this brand of waterproofing, based on the use of a specific base and characteristics of the protective layer.

Thus, the roll insulation of the Uniflex HPP model stands for a material with a fiberglass base, covered on both sides with a protective film.

Rolled waterproofing TechnoNIKOL

Rolled waterproofing, produced under the brand name of TechnoNIKOL, occupies a leading position in the ranking of building materials in the international market. The basis for the popularity of TechnoNIKOL brands are:

• high degree of reliability and effective protection against moisture and condensation;
• biological and chemical resistance, maintaining flexibility and elasticity at low temperatures;
• the ability to withstand a significant tensile load;
• long-term service life - from 35 years;
• ease of installation, economy.

The strength of TechnoNIKOL waterproofing materials is due to the use of a multilayer structure consisting of a polyester base, two layers of bitumen-polymer filler and a protective film. All coatings are produced in strict accordance with GOST and current building codes.

Under the TechnoNIKOL brand, new models of rolled waterproofing are being developed, taking into account various climatic conditions and the production capabilities of the consumer. Baseless self-adhesive roll coatings are widely used for waterproofing floors and foundations.

In addition to moisture protection, waterproofing coatings from TechnoNICOL are capable of protecting premises from noise, dust, and harmful gas.

Roofing and insulation materials are used both in the construction of new buildings and in repair and restoration work. The scope of waterproofing from TechnoNIKOL includes:

• strengthening foundations under industrial structures;
• construction of high-rise buildings;
• hydroprotection of private households from the damaging effects of dampness and moisture;
• construction of tunnels, viaducts and bridges using reinforced concrete slabs.

Modern roll materials for waterproofing are able to effectively and reliably protect a building or structure from groundwater, freezing and precipitation. The right choice of waterproofing, strict adherence to the recommendations of experts and installation technology are the basis for successful laying of rolled waterproofing and the durability of the structure.

Overview of manufacturers Izover, Knauf, Ursa

The quality of the insulator, of course, depends to a certain extent on the manufacturer.

knauf-1
knauf-2

• Knauf is a product of a German manufacturer, created from natural mineral wool using the latest ECOSE technology. It is an environmentally friendly insulator, since it does not contain formaldehyde. Even with direct contact with this material, it remains safe for humans and does not cause allergies. It can even be used indoors. This is a reliable protection against cold and noise.

Distinctive characteristics of Knauf materials:

• high degree of vapor permeability;
• low water absorption;
• chemical and biological inertness.

isover-1
isover-2

• French isover isolation. This is a relatively cheap option for roof insulation. This is the most dense material among analogues. It is produced in rolls of different thicknesses: 2, 3, 5, 10 and 15 cm. What are the advantages of insulation roll isover classic. Reviews show that he

• excellent sound insulator;
• environmentally friendly;
• does not burn, when exposed to an open flame does not have toxic emissions;
• durable;
• easy to install.

ursa-1

• Ursa is another popular brand. It is distinguished by its durability, does not break or crumble, it is easy and simple to work with it. Available in different widths: 5; 8 and 10 cm.

Types and characteristics

Mineral wool insulation materials are widely used.

Their popularity is explained by high operational and technical indicators and relatively low cost.

Mineral wool-based roll insulation includes:

1. . The material is obtained as a result of the remelting of rocks of a certain type and the formation of fine fibers.
2. Glass wool. Insulation made from molten broken glass has an affordable cost. Due to this, the material is in high demand, although it is considered obsolete.
3. Slag. The material is based on waste from the metallurgical industry, so it has a rather low price.

Mineral wool-based heaters have their own distinctive properties:

• temperature resistance;
• low thermal conductivity;
• high density;
• absorption of vibrations and sound vibrations;
• no shrinkage after prolonged use.

Foil roll insulation is made from expanded polystyrene foam by applying it to a layer of foil. The foil creates the effect of a thermos, pushing heat back into the room.

Expert advice: foil insulation can be used when installing an infrared floor, for thermal insulation of wooden saunas and baths.

The main properties of foil rolled insulation can be called:

• high thermal insulation;
• reliable vapor barrier;
• good sound absorption;
• fire safety;
• durability.

Mezhventsovye roll heaters are a rather specific solution. The main purpose is to fill the empty space between the crowns. Even high-quality assembly of houses from profiled timber or logs cannot guarantee a snug fit of the elements. The interventional heat insulator will fill the free space.

The material is produced in narrow rolls, for its manufacture natural and harmless materials are used, such as linen, batting, jute. The use of this type of insulation is possible both during construction and during the operation of the house. Everyone knows that over time the tree dries out, forming gaps between the elements of the structure. Filling the resulting voids with insulation using a chisel and a mallet, you can keep the heat in the house as much as possible.

Heat insulators based on mineral wool

The materials of this group are the most common in the domestic market. This is due not only to their excellent operational and technical data, but also to an acceptable pricing policy - such a combination is still unattainable for competitive offers.

Flexibility makes work easier

Assortment and features of species

The term "mineral wool" is a unified designation for a number of heat insulators, namely:

• basalt wool - for the manufacture of this material, the technology of remelting certain rocks is used, followed by the formation of the finest fibers on their basis, woven into a single carpet;
• glass wool is a material, although it is obsolete, but still in high demand due to its affordable cost. For its production, remelted cullet glass is used;
• slag wool - it is based on waste obtained in the metallurgical industry. Due to this, such a heater in rolls has a lower cost than that of basalt and glass wool.

Each of the varieties of mineral wool has its own distinctive features and characteristics. So, glass wool perfectly resists high temperatures, up to 450 degrees - after exceeding this parameter, the material is destroyed irreversibly. The highest density is 130 kg / m3, thermal conductivity indicators vary in the range of 0.038–0.046 W / m * C.

Glass wool in rolls

Glass wool is not combustible, it does not even smolder, perfectly absorbs vibration manifestations, resists sound vibrations and does not shrink even during long-term operation. At the same time, the material is not moisture resistant, and its wetting completely eliminates the entire range of positive characteristics. It is worth noting the fragility of glass wool, as well as the fact that contact with human skin causes severe itching.

As for basalt wool, such rolled thermal insulation is able to withstand temperatures up to 700 degrees. Its thermal conductivity is 0.035–0.045 W / m * C, the density reaches 220 kg / m3. The material is resistant to moisture, slight wetting does not affect its parameters at all. Basalt wool is an environmentally friendly and non-irritating material.

Basalt wool

Slag wool has the largest mass, and its density reaches 400 kg / m3. The material is characterized by a minimum thermal conductivity - 0.046–0.048 W / m * C, and the highest temperature that it can withstand is 300 degrees - its increase causes the melting of slag and the destruction of its structure.

Slag wool in rolls

The dimensions of the materials largely depend on the manufacturer, but most often they have the following sizes:

• length - varies between 3-6 m and more;
• width - the standard figure is 0.6 and 1.2 m, although products of individual brands may have a width of 1.22 m and 0.61 m;
• thickness - 50, 100 and 150 mm.

Wall mounting

Despite the fact that the roll insulation is created from different materials, it is mounted on the wall according to the standard principle. All differences will be in the composition of the adhesive that will be used, and, accordingly, in the drying time of the substrate on the wall.

Conditions for carrying out installation work with a substrate in the room

To glue the insulation on the walls of the apartment, you have to do the following:

• First of all, it is worth preparing the surface, for which you need to remove the old wallpaper, plaster the wall, smoothing and patching up large cracks and bumps. Small defects in the wall surface can be left, they will close.
• Next, the surface of the wall must be primed. This is done either with the help of glue, with which we will glue the substrate, diluted in a weaker consistency, or with the help of a special primer composition. After the primer, you must wait until it is absorbed into the wall and dries.
• It is recommended to cut the roll insulation into pieces of the required length in advance so that it can lie down and level out. This will make it much easier for us to glue it. When cutting the canvas, add a little material for insurance.
• We prepare the adhesive composition according to the instructions on its pack. If we are dealing with a substrate with a top layer of paper, then we apply glue to the wall and to the cut pieces, while letting them soak in the composition for literally 5 minutes. If the substrate is equipped with non-woven edges, then it is enough to spread the wall, and the material will easily attach to it.

• Next, we proceed directly to the installation of canvases on the walls. This process is reminiscent of wallpapering, the pieces are also glued together and carefully smoothed out. Air is expelled from under the canvas and it is firmly glued to the wall. It is convenient to use a rubber roller, it will create the necessary pressure and will not damage the insulation sheet.
• After the insulation has dried, after about 1-3 days, we seal the joints of the canvases with ordinary masking tape. Krepp will give solidity to our design.
• Now our walls are qualitatively insulated, and you can proceed directly to gluing the wallpaper itself.

Wall insulation will allow us to create the most comfortable living conditions. It will serve us for a long time, no matter how many wallpapers hang.

Wall insulation with roll insulation is most often used in cases where the area of ​​\u200b\u200bthe walls is significant, and there are long straight spans. In this case, it is possible to achieve a significant savings in the cost of materials and performance in comparison with heaters in the form of plates or mats. A variety of insulating materials are supplied in rolls, from mineral wool to pressed cork. Each of them has its own advantages in specific conditions. Installation of roll insulation is not a complicated operation and does not require highly qualified workers or expensive equipment.

Main types

Experts distinguish the following features and varieties of insulation supplied in rolls.

According to the material, heaters are divided into several varieties:

• Mineral (, glass or slag wool). Usually used for exterior walls.
• Polymer - based on foamed plastics. Used to insulate walls from the inside and outside.
• Cork - from the pressed bark of the cork tree. Rolled cork insulation for interior walls is attached under the wallpaper.

Mineral and polymer roll insulation can be glued on one side with aluminum foil to reduce thermal conductivity and improve waterproofing. A thin layer of foil reflects over 95% of thermal radiation, returning heat to the insulated room. The foil not only reflects heat well, but also increases the strength of the material.

Mineral basalt wool in a roll

Characteristics

Roll insulation materials are characterized by the following main parameters:

• Environmental friendliness. All models on the market must comply with building safety requirements for installation, operation and disposal. They must contain small amounts of harmful substances, these substances must not be released from the insulation during its storage, installation and during use. The packaging indicates the method of disposal. The materials are resistant to organic solvents and other active substances.
• Fire and biosecurity. Mineral insulation does not burn itself and prevents the spread of flame. Foam materials are able to withstand fire for a certain time. Materials prevent mold and repel rodents.

• Air and vapor permeability. Key characteristics. They show how much air or water vapor at a certain temperature can seep through a unit area of ​​the material. Vapor permeability is necessary in order to remove excess dampness from the room to the outside through the walls and their ventilation systems.
• Strength. An important characteristic of insulation for wallpaper. Touching, including with hard objects, should not damage the wallpaper.

Advantages and disadvantages

The main advantages of roll material are:

• Versatility. Suitable for thermal insulation of any surfaces. For complex spatial shapes, including curvilinear, a suitable piece can be cut.
• Minimum requirements for surface preparation prior to laying.
• Benefit in terms of material price and work productivity when insulating large wall areas, especially straight sections.

They have rolled materials and disadvantages.

• High labor intensity when laying in a frequent crate, additional time is required for cutting.
• Low rigidity does not allow them to be used where it is required to withstand significant loads.

In general, the advantages compensate for the disadvantages, which explains the high popularity of roll materials among consumers.

Materials are harmless to health, provided they are used correctly and fire-fighting regime is observed.

Popular brands

The domestic market does not experience a shortage of rolled materials. In different types, different manufacturers are leading.

Knauf

The German company produces excellent mineral heaters. They are free from formaldehyde and other harmful substances, thanks to a specially designed fiber structure, they do not provoke allergic reactions. However, the manufacturer recommends that installation work be carried out with thick gloves. They perfectly muffle noise, impregnated from insects, rodents and mold.

Mineral wool Knauf 1220X6148X50

• Dimensions 1220X6148X50 MM (15 m 2).
• Thermal conductivity: 0.037 W/(m°K).
• Density 12 kg/m 3 .
• The cost is 1100-1200 rubles.

Isover

The French company launched production at local sites. Offers a wide range of rolls with a thickness of 20 to 150 mm, allowing you to keep warm in all weather conditions. There are many foil models that can be used in rooms and buildings with high humidity.

Isover Klassik 50 mm thick

• Size 50*1220*5490mm.
• Packing 13.4m 2 , 0.67m 3 , 2 mats.
• Thermal conductivity 0.04 W/(m*K).
• Density 10.5 kg/m3.
• Price from 750 rubles.

ursa

Easy to install material has a long service life, excellent fire protection properties.

For wall insulation, Ursa Geo M11 is available.

Ursa Geo M11 for wall insulation

• Size 7000x1200x100 mm.
• Average density - 11 kg / m³.
• Combustibility group NG.
• Thermal conductivity - 0.040 W / (m ° K).

Topizol

Foamed roll material is produced with a thickness of 3 to 20 millimeters. Works great in high humidity conditions. Not subject to decay. Very light, easy to mount. Foil models resist strong gusts of wind (subject to proper installation). It is characterized by excellent vapor permeability.

Foamed polyethylene

• size 8 mm (18 m 2) wide. 1.2m;
• weight 8 kg;
• price 850 - 1100 rubles.

It is a good choice for wall insulation, including loggias, attics, attic spaces. It has a low density, which makes transportation and handling easy and convenient.

The manufacturer claims a service life of 30 years.

Penofol

The heat-insulating layer is made of polyethylene foam. Several types of penofol are produced:

• A - foil on one side.
• B - foiled on both sides.
• C - foil on one side, a layer of adhesive is applied on the other to facilitate installation.

Available in thicknesses from 2 to 40 millimeters, foil thickness - 30 microns. It does not emit any harmful substances, it is recommended for warming children's rooms.

B. Double-sided filming

• Foamed polyethylene Penofol B-10 15000x1200x10 mm.
• Vapor permeability: 0.001 mg/(m h Pa).
• Density: 35 kg/m3
• Thermal conductivity: 0.049 W/(m*K).
• The cost is 1400-1600 rubles.

What to consider when working

Insulation with mineral roll materials can be carried out at any time of the year, it is only important to protect the material from precipitation.

The use of foam materials mounted on an adhesive layer depends on the air temperature. Usually limited to -10C. Special adhesives are also produced, effective up to -20C.

Before the start of insulation, a minimum surface preparation is required:

• Dismantle pipes, electrical wiring, lamps, decorations, plants, etc.
• Clean the walls from the remnants of old coatings, debris and dust.
• Install a crate for mineral insulation.
• Level and clean the surface for gluing foamed thermal insulators.

Installation does not require special equipment, from the tools you will need:

• construction knife;
• stapler;
• screwdriver;
• a hammer;
• double sided tape.

It is more convenient to carry out installation and cutting of rolled heaters together, especially with large amounts of work. Small volumes are within the power of one master.

Warming process

The sequence of operations for the installation of mineral heaters is as follows

• A vapor barrier film is attached to the prepared wall.
• A crate is mounted from wooden bars or metal profiles. The recommended guide pitch is 50 or 60 cm.
• Rolls are cut according to the selected pitch. Cutting should be carried out so that the insulation enters between the guides tightly and, straightening out, provides a better fit to the guide.

Dowel dowel

The widely used heat-insulating plates have been replaced by rolled heaters, which are more convenient and improved in functionality. Such products are suitable for finishing roofs, walls, utilities, ventilation shafts and other surfaces of complex shape. Rolled insulation has improved technical performance in comparison with mineral wool in slabs, it is characterized by increased density and rigidity.

The flexibility of the insulation will help you in the shortest possible time to complete the work on the insulation of your home

Flexible thermal insulation in rolls

The material has an affordable cost, excellent performance properties. The scope of its application is repair finishing and capital construction, when there is a need to increase the thermal insulation performance of surfaces:

• balcony;
• basement;
• gender;
• floors;
• attic.

Which insulation keeps heat better:

There are roll-type heaters based on mineral wool, which are glued to the walls directly under the wallpaper. Their main purpose is to increase the temperature inside the room, reducing natural heat loss in the cold season. Additionally, such materials prevent the development of mold and mildew, the formation of high humidity. The uneven surface is perfectly masked due to the soft insulation, which does not require finishing work.

Characteristic features and differences of heaters:

The versatility of rolled thermal insulation based on mineral wool determines the wide scope of its use. . It is indispensable in the modern construction industry., creates a durable working layer of insulation that protects from the cold:

• Living spaces;
• offices;
• warehouses in enterprises;
• outbuildings;
• baths and saunas.

Insulation, soundproofing walls for wallpaper:

Soft thermal insulation is not damaged by regular contact with ventilation ducts and pipelines. Due to sufficient flexibility, it tightly covers uneven surfaces, and can be laid at sub-zero temperatures.

Material Advantages

Thermal insulation in rolls designed with weaknesses in mind, which characterizes a similar material in slabs. It has a number of positive aspects:

1. Minimization of thermal conductivity even among models belonging to the budget class.
2. A large assortment range of roll insulation, which are based on various types of mineral wool. They differ in terms of performance.
3. No damage by rodents, fungi, microorganisms.

The presence of a large assortment of heaters, will allow you to choose the best for you

1. Resistance to temperature extremes, adverse weather conditions while maintaining the original thermal insulation performance.
2. Noise-reducing feature, resulting in increased sound insulation in the equipped room.
3. Resistance to open fire.
4. Ease of installation, which even an inexperienced master can handle.

Like other universal materials, soft insulation has a drawback. They are characterized by increased vapor conductivity, which can be eliminated by an additional layer of vapor barrier.

Main types and characteristics

The main component of the described materials is usually mineral wool. It, in turn, is presented in several versions:

1. Slag. The insulation is made from waste from the metallurgical industry. It differs in strength indicators, while being the cheapest and most affordable product.

Slag wool is one of the cheapest materials that provides good thermal insulation.

1. Basalt wool. The peculiarity of heaters in rolls for walls and other surfaces is that they are produced using the rock melting technology. Then, thin layers are formed from the resulting content, intertwined into a single carpet.
2. Glass wool. The heat insulator is created from pre-melted glass cullet. This approach to the production process significantly reduces the final price of the described products.

The disadvantage of glass wool is the increased fragility of the fibers that cause itching.

Each of the designated heaters has a specific set of characteristics. But in any case, they all represent an improved version of the standard mineral wool. For example, glass wool exhibits excellent resistance to high temperatures: a heat insulator made from it can withstand up to +400°C. Exceeding this mark entails the complete destruction of the material with the impossibility of recovery.

Which heater is better:

As for the highest rates of thermal conductivity and density, they are typical for rolled insulation made of glass wool. It tolerates vibration manifestations well, does not smolder and does not burn, absorbs sound vibrations.

There is no shrinkage of such material throughout the entire operational period.

Of the unpleasant moments, there is irritation of human skin upon contact with fiberglass wool, slight instability to moisture.

The presence of the pros and cons of each of the materials will help you choose the best material for: home, cottage, bath

Thermal insulation rolls made of basalt wool also withstand high temperatures, are distinguished by sufficient density and thermal conductivity. Excellent resistance to high humidity. Even when completely wet, the original quality indicators are preserved. Such material is completely environmentally friendly, does not cause irritation upon direct contact, does not cause allergic reactions.

The heat insulator made of slag wool can withstand a temperature load not exceeding +300°C. Otherwise, the slag melts, the structure of the described building product is completely destroyed.

Rolled thermal insulation materials differ in parameters and functionality. It all depends on the brand of products, the manufacturer, the requirements of the buyer in the manufacture of the product to order.

The role of the foil surface

The main feature of such insulation devices is the presence of a thin but durable foil coating. In this way, the material is protected from the negative effects of ultraviolet rays and high humidity, which is very important when equipping industrial premises, kitchens, bathrooms, baths, saunas.

Foil insulation tolerates high temperatures well

Laying foil insulation is carried out in accordance with a special technological process. A gap of 1-1.5 cm is necessarily created between the thermal insulation and the finishing material. This is very important, since at elevated temperatures the insulation maintains a given degree by transferring it to the back wall and then returning back to the walls, but not to the room.

In comparison with roll materials made of slag wool, glass wool and basalt base, the foil product must be fixed on the crate. The layers are overlapped, the places of their joints are carefully treated with insulation.

When choosing a material, consult with a specialist, he will help you choose the best material

Before buying soft thermal insulation for finishing a room for any purpose, you need to take into account some tips shared by experts. The features and type of the surface to be treated are important, which can be brick, concrete, wood, etc. An aspect such as the thickness of the base should not be overlooked when it comes to external insulation. In this case, the frequency and intensity of precipitation plays an important role., temperature regime by seasons.

A rolled heat insulator made on the basis of any type of mineral wool must be sold in undamaged packaging. Otherwise, moisture accumulates inside the material, worsening the quality of the product. When choosing the described material, its main functionality and purpose are taken into account.

Heaters in rolls - a demanded finishing product. They are easy to use, improve the thermal insulation of premises for various purposes, keeping it at the proper level for many years.

Knauf heater:

The not always convenient and functional thermal insulation boards are replaced by an improved version of thermal insulation - roll insulation, which is equally effective both for walls and for ventilation ducts, pipes, roofs and other surfaces. The material has improved technical parameters and, unlike mineral wool in slabs with high rigidity and density, allows it to be used for elements with complex geometry.

The heater has high performance and technical characteristics, is sold at an affordable price. Rolled insulation is used both in repair and capital construction to improve the thermal insulation properties of surfaces:

• basement;
• attic
• balcony;
• gender;
• coverings, etc.

A standard mineral wool-based roll insulation for wallpaper on walls in a living room allows you to increase the temperature by several degrees by reducing heat loss.

Additionally, the material prevents the development of dampness, the appearance of fungus and mold, and if there is an uneven surface, it hides flaws without additional work.

The wide scope of mineral wool in rolls allows us to talk about its versatility. The material is practically indispensable in modern areas of construction, it allows you to create a really working and durable layer of thermal insulation both in apartments and houses, and in outbuildings, at enterprises, saunas, baths, etc.

Particularly important is the ability of the material to come into contact with pipes and surfaces of ventilation shafts. In this case, rolled thermal insulation is arranged primarily due to the elasticity and flexibility of the material. Rolls are easy to use, allow you to finish uneven surfaces, including at sub-zero temperatures.

Advantages of thermal insulation in rolls

Comparing roll insulation with conventional mineral wool boards, the advantages of the former are obvious. These include:

1. The minimum indicators of thermal conductivity, including among budget models.
2. Resistance to atmospheric phenomena, temperature fluctuations, rodents and microorganisms while maintaining the main thermal insulation properties.
3. A wide choice of material based on different types of mineral wool for warming surfaces with different performance characteristics and features.
4. Resistance to high temperatures (up to 700 degrees Celsius), open flame.
5. Noise-reducing properties, which allows you to increase the level of heat and sound insulation.
6. Ease of installation.

There is also a small drawback in rolled thermal insulation based on mineral wool - high vapor conductivity, which will require a vapor barrier layer.

Types and characteristics of thermal insulation in rolls

At the heart of the insulation in rolls is mineral wool, which can be presented in several versions:

• in the form of basalt wool;
• glass wool;
• slag.

Materials based on basalt wool are created using the technology of remelting rocks with the formation of thin rocks woven into a single carpet on their basis.

For the manufacture of materials based on glass wool, remelted glass cullet is used, which can significantly reduce the cost of finished heat insulators.

For thermal insulation in rolls based on slag wool, mainly waste from the metallurgical industry is used. Compared to heaters based on the above-described heaters based on basalt wool and glass wool, it is the cheapest.

Each of the mentioned thermal insulation materials has its own set of characteristics, despite the fact that they are all an improved version of mineral wool. So, for example, glass wool is sufficiently resistant to high temperatures. The heat insulator is able to withstand up to 450 degrees Celsius, when the temperature rises above the specified mark, the surface is destroyed and cannot be restored.

Glass wool-based materials have the highest density and thermal conductivity. The rolls are not combustible, do not smolder, perfectly cope with vibration manifestations, suppress sound vibrations and, most importantly, do not shrink, regardless of the length of service life.

Of the minuses of materials based on fiberglass wool, it is worth noting the instability to moisture, as well as the unpleasant consequences that occur when it comes into contact with human skin.

Heat insulators based on basalt wool in rolls withstand high temperatures up to 700 degrees, have excellent thermal conductivity and density. Unlike fiberglass wool based heat insulators, materials are able to withstand moisture while maintaining basic performance characteristics even after getting wet. Heat insulators belong to the group of environmentally friendly materials that are not capable of causing allergic reactions.

Slag wool - thermal insulation for warming surfaces, the operating temperature of which does not exceed 300 degrees Celsius. The density of materials reaches 400 kg/m3, thermal conductivity ranges from 0.046 to 0.048 W/m*S.

The temperature exceeding the specified limit will lead to the melting of the slag with the destruction of the structure. Depending on the manufacturer, you can choose materials for thermal insulation based on slag wool with suitable parameters: length - from 3 to 6 m, width - from 0.6 to 1.2 meters, thickness - from 50 to 150 mm.

Heat insulator with a foil surface: features

Foil insulation materials have one main feature - the side with a layer of foil, designed to reduce surface exposure to ultraviolet rays and additional protection from moisture. Use materials for warming surfaces indoors with a base of different types of wool.

It is necessary to work with foil thermal insulation according to a special technology, observing some nuances, for example, not forgetting a small gap (no more than 1.5 cm) between the finish and the thermal insulation material. This is important, because when the temperature rises, the insulation will keep the temperature, transferring it to the back wall, returning it back to the walls, but not to the room, as necessary.

Another important nuance is that, unlike heaters in rolls based on basalt, fiberglass or slag wool, the foil heat insulator is mounted on the crate, overlapping and treating the joints with insulating material.

Tips for choosing thermal insulation in rolls: what you need to know

Summing up all of the above, it remains to note several important nuances regarding the choice of materials based on roll-type mineral wool for insulation. Experts recommend first of all to take into account the type of surface and purpose. It is necessary to select materials suitable for thermal insulation of certain surfaces: wood, concrete, brick, etc.

Do not write off the thickness of the base, taking into account temperature indicators and precipitation in the region, especially when it comes to external insulation.

When buying materials for thermal insulation based on any of the listed types of wool, you should pay attention to the integrity of the package. It is strictly forbidden for moisture to form on the material in the packaging.

Each of the types of insulators listed above has its own characteristics, advantages and disadvantages, so the choice should be made after a thorough analysis of them, depending on the required functionality.