The first paper stapler was made in the 18th century for the French Emperor Louis XV. Each staple was marked with the sign of the royal court.
In 1867, D. McGill received a patent for a press that allowed sheets to be fastened using brass fixtures.
His device became the basis for modern staplers. Modern devices are smaller and lighter. They are much more convenient to use.
Types of staplers
In 1997, the stapleless stapler was invented. This stapler staples paper into small strips cut from paper. Therefore, its owner does not have a question about how to charge the stapler. There are three types of staplers: standard, mini and construction.
They are equipped with a manual or electric drive. A stationery stapler is used to staple paper sheets with metal staples. It is used to make brochures and notebooks. The conventional stapler staples up to 50 sheets. One pack contains 20 plates of 50 staples. When you press the handle of the device, the spring that is inside is stretched and unclenched, driving in the bracket. It passes through the paper and hits the deflecting plate, which bends its ends. Some models of staplers bend the staples in two different ways: inside or outside. In the second case, the bracket is easily pulled out. This stitching method is used to temporarily secure the sheets. At the back of some models there is a protrusion for extracting the staples. They are also equipped with a mechanical amplifier. best material for the stapler - metal coated with plastic. To prevent the device from scratching the surface of the table, plastic or rubber pads are put on its bottom.
A construction stapler is used for upholstery of furniture and walls. It has a high rate of fire and fires up to 60 hits per minute.
There are also stapler cartridges in some models of copiers and printers.
How to load the stapler with staples?
Before filling the stapler, you need to make sure that the selected staples fit it in size. Manufacturers indicate their size on the packaging of the device. For convenience, they are marked with numbers. How to charge the stapler? Most models open from the top. In some cases, before opening, you need to move the side fasteners. Other staplers open at the push of a button. The opening method is indicated in the user manual.
How to load the stapler with staples? They are placed in the compartment so that their ends fall into the slots. You can use tweezers to refill the mini stapler. Then the stapler is closed. In this case, a characteristic click should be heard. The stapler is checked by fastening a pack of sheets of paper. If the staples are bent and stuck inside, you need to open the stapler and align their rows.
How to charge the stapler? First you need to make sure that the stapler is locked. Then you need to find the button that opens the tray. It is usually located on the back of the device. How to charge the stapler? Remove the staple holder from the device. The remaining staples are discarded. The stapler is cleaned of dust and debris. Then it is turned over and the staples are inserted into it upside down.
Using a stapler, without any nails, you can fasten materials of small width and density. It is an indispensable tool in stationery, construction and furniture industry. In the article we will figure out how to insert paper clips into the stapler.
Stationery staplers
These tools are very simple and designed for the average average layman who is not versed in technical "troubles". Everything is simple here. recline top cover- and the spring with the clamping mechanism drove back. Insert a clip of paper clips with the tips down and close the lid. The clamping mechanism returns to its place, and the tool is ready for work again.
Those who wish can watch a video in which the boy shows how it is done correctly.
Construction staplers
They are more massive and have a slightly different structure, although the principle of operation is the same. The spring clamping mechanism pushes the clip clip to the shock, after each operation the next clip takes its starting position and as a result of pressing the spring key, the shock mechanism drives it into the right place, thereby pressing the next sheet of cardboard against the wall with the clip, the material against the wood from which the frame is made upholstered furniture, or just for the formwork of the future concrete foundation. Let's figure out how to insert paper clips into a construction stapler.
Wrong option
The mistake of many is that when the stapler runs out of staples, they, having pulled back the double-sided protrusions of the frame lock, open it and try to insert the next clip of staples through the front part from the side of the impact mechanism. As a result, with an awkward movement, the spring mechanism now and then throws the clip back, and it flies away for many meters, after which it has to be searched for a long time. Often, a clip can also fly into the eye of an unlucky "stapler operator." Here is a video that shows how not to do it, although the operator himself does not suspect it.
Correct option
The right way How to insert staples into a stapler of a construction or furniture variety is to, by pressing on the back of the spring-loaded staple feed holder, release its groove from the lock hole and pull it out completely. After that, you can even insert more than one clip into the frame and return the spring of the mechanism to its place, thereby ensuring it for a long time smooth operation. Here is a video on how to do it right.
The frame should be opened as in the first, incorrect case only when one of the staples gets stuck in the exit slot.
We hope our article was useful to you. Happy reloading!
A stapler (translated from English. “Stapler”) is a necessary thing in the office. The stationery stapler is designed for fast fastening sheets of paper using metal staples.
Types of staplers
Staplers are divided into several types: according to the number of sheets that can be stitched at the same time.
Mini stapler
Compact model that can be put in your pocket. Staples 10 to 20 sheets. Staples for a mini-stapler are different: 10, 24/6. The design and color of the case is very interesting: colored, transparent, there are devices that look more like a toy than a stapler itself.
Desktop stapler
A fairly compact stapler, does not slip on the table and does not leave scratches on it, as it has a rubber sole. Staples 10 to 50 sheets. Standard staples are used: 10, 24/6-8.
Booklet stapler
A specialized stapler with adjustable stitching depth. Equipped with a ruler for ease of use. Stitches brochures, catalogs and newspapers to the fold of the pages. Designed for different amount sheets, works on different brackets.
Printing or printing stapler
The most powerful stapler. Staples archives, voluminous stacks of paper. It is used in state institutions, libraries, clinics. On average, stitches up to 250 sheets. Designed for both standard brackets and specialized ones.
Anti-stapler (destapler)
Designed to remove staples from paper. The anti-stapler is often built into the stapler itself, it extends from the back of the stapler and, with the help of a pointed tip, pry and remove the staple. But a small object resembling a frog looks much more original on the table, which firmly grabs the bracket from both sides. Anti-staplers come in the form ordinary knives for paper with a curved tip.
stapler-player
Plier is a special stapler in the form of tongs, it can be used on a canopy. The player is used by florists when packing bouquets, it is suitable for attaching labels or tags to fabric.
Tucker
This is a "mounting stapler", made in the form of tongs. Clogs staples like nails. It is used for pinning ads and posters. Interestingly, many of the desktop staplers found today function as a tacker.
Staplers also differ in the type of staples that are used with them.
Stapler No. 10
Designed for fastening a small number of sheets, usually up to 15 sheets of standard weight paper.
Stapler No. 23
The most powerful stapler.
Works with staples 23 types. Staples up to 260 sheets of paper, depending on the length of the staple used.
Staplers No. 24
Universal stapler, fastens both a small amount (1-2 sheets) and a large amount (20-30 sheets).
What to look for when choosing a stapler
. Staples
Two numbers are always written on brackets, for example, 24/6 - what does this mean?
The first number is the type of bracket. This is a conventional unit, which includes the width of the bracket, the dimensions of the section and the steel grade of the wire (caliber) defined for this standard.
The second number is the leg height. It is measured in millimeters. The higher the leg height, the large quantity sheets can be stapled. The thickness of the bracket increases in proportion to its height. To determine maximum thickness stitched sheets, subtract 3-4 mm from the length of the legs for their bend.
When choosing the length of the staple leg, remember the main rule - 2/3 of the leg should be in the fastened material, and 1/3 will hold the attached material.
A high-quality bracket is made of notched wire (equal in diameter on any segment) - then all the brackets will be equal. A quality staple has pointed ends that make it easy to pierce the paper.
What brace material to choose? For fastening thick paper and large stacks, we recommend using steel wire staples, as it is stronger than galvanized iron. By the way, all staples with a leg height of 10 mm or more are made of steel.
The quality of staples is related to the reliability of the stapler, so if you buy a quality stapler, then you should also purchase the appropriate staples.
. Internal organization stapler
The internal mechanism of the stapler has a very great importance and affect the performance of the device.
The stapler motor system is driven either by a spring or a special metal plate. What's better? The plate is more practical: it lasts longer and provides a softer glide, and the spring has a habit of stretching. The stapler tongue is made of metal (more durable) or plastic (provides smooth feeding of staples).
. Case and design
Pay attention to the material from which the stapler is made - its durability depends on it. The metal case is more reliable in operation and looks very impressive. But plastic also has advantages: it is lighter, more convenient to transport, it is more pleasant to hold it in your hands. Models with combined cases are very convenient: metal + plastic, metal + rubber, metal + plastic + rubber.
The color of the stapler depends on the size and specific application.
The more powerful the stapler, and the more functions it performs, the more restrained its color.
. Power and depth
The characteristics of the stapler always indicate the punching power (or the amount of bonding) - how many sheets or millimeters of paper the stapler punches. As a rule, office paper for printing with a density of 80 g/m2 is taken into account.
Punch depths are the distance from the edge of the paper to the punched area. The depth of the firmware in mini staplers is 35-40 mm, in a desktop stapler - from 50 mm or more.
. Package
The quality of stationery will always tell the packaging, whether it be a stapler or staples to it. In addition, the product itself must have a marking indicating the country of origin, the company and the type of staple used. Sometimes the stapler comes with a pack of staples.
. Paper
Thickness standard sheet office booms - 80g/sq.m. It should be borne in mind that, depending on the thickness of the sheets to be stitched, the power of the stapler will also vary.
How to charge the stapler
Before you load your stapler, determine the staple size that is appropriate for your stapler.
The number of the staple used in a particular stapler is written on the package.
Open the stapler cover. It is connected by a spring to a plastic element that presses the staples against the opposite edge of the metal groove into which the staples are placed. Opening the cover will pull the spring along with it, and behind it the plastic element, thus freeing up space for new brackets.
Take one section of staples and place them in the metal groove with the ends down. Close the lid and click the stapler once to sample. If a bracket with the ends concave inward fell out of it, then everything works, but if this did not happen, or the bracket is bent incorrectly, repeat the procedure or change the stapler.
← back
Mechanical stapler allows you to nail plastic panels, clasps for lining, fabric for furniture, wooden or plastic surfaces.
There are three types of staplers: mechanical, electrical and pneumatic.
Mechanical staplers are affordable, compact, lightweight, and easy to maneuver. In the following, we will only talk about them.
How to choose a stapler?
In short, it is undesirable to buy the cheapest options, as well as plastic models. metal tool more powerful and more reliable.
Choose professional models that have an adjusting screw (lamb) at the top. It helps to regulate the force with which the tool will punch through the material.
Many people forget
Before working, adjust the adjusting screw according to the material of the surface to be worked on.
If it's a hard plywood, it will need a lot of punching through the material, so it's worth setting a lot of force. If it is a loose surface, the force must be reduced so as not to break through the fabric, or for example pvc panel which you shoot.
During operation, it is recommended to press the lever with one hand, and thumb second hand to press the adjusting screw. Then the return will be minimal and the load will be distributed evenly in the stapler. You will be able to hammer in the brackets much better.
How to load staples into the receiver
The design of all mechanical hammers is almost the same. There is a handle-lever, due to which the pressure occurs, and at the bottom of the stapler there is a metal plate that opens the receiver. Here we have to load the brackets.
Before buying brackets in hardware store, you need to find out which size is suitable for your device. As a rule, the size and type of suitable staples are indicated on its body.
For example, on the body of our stapler, the width is 12 mm and the depth is 6-14 mm. This means that you will only be able to charge staples from that range.
Parentheses less or bigger size will not fit the receiver. The size of the staples in millimeters is also indicated on their packaging.
To fill the shells into the stapler, you need to open the metal plate on rear surface.
To do this, you need to take it big and index finger on both sides, then pull towards you and slightly down. Thus, we wring out the metal tab on the back of the plate, and pull out a metal spring, similar to the one in a regular stationery stapler.
If there are still staples left in your stapler, they will fall out after you pull out the spring. If they are not there, then it is time to put new ones for further work.
Staples are inserted into the receiver (hole in the position of the letter "P").
How many shells will fit
Now a little about how many shells fit in the stapler. Staples are sold in small rows. The row can be divided into several parts independently, slightly breaking it with your hands.
1-1.5 rows are loaded into the tool. 2 rows rarely fit in the receiver, so if there is a lot of work to be done, it is better to prepare halves of the rows before starting work.
What to do if the bracket is stuck
It is worth noting another very important point which will help you in your work.
How to fill a construction stapler with staples
It happens that the brackets are bent and stuck in the exit hole. They cannot be hammered into the surface and cannot be pulled out by hand.
In this case, we need to pull out the feed magazine completely.
This possibility exists for almost all professional staplers.
First you have to repeat the opening of the metal plate and pull out the spring.
In this way, you will pull out the entire feed magazine that was in the tool.
You will see a jammed bracket, which is now easy to pull out with your hands.
Assembling the stapler back is not difficult: the entire pulled out block returns to its place with a push.
When you do this, you should hear a click. After that, do not forget to put the spring in place.
More than just brackets
Some staplers can work not only with staples, but also with cloves. various forms. The designations with which the stapler works are indicated on its body or in the instructions.
Carnations are tucked into the stapler in the same way with staples, but you need to be careful after pulling out the spring. A number of carnations must be loaded along one of the outer faces of the letter "P", and not inside this very letter!
If you want it to give out two nails at once side by side when working with a stapler, the second row is loaded along the second outer edge. Next, the spring is inserted and the stapler closes.
Stapler, how to charge a construction stapler?
Very often in construction there is a need to connect parts. This is done with nails or staples. On the modern level using a tool such as a stapler. There are many types of this tool, but in all the principle is the same - staples. The stapler can be charged independently when they run out.
How to fill the stapler
They, like the stapler, are sold in any hardware store or in the construction markets. There are features that you can see in this video.
To paste new block staples in the construction stapler, remove the clamping bar, which is located in the back of it from below
Next, insert the staples down with the paws and insert the clamping bar again. In order for the stapler to work without interruption and not beat either two or three staples at once (you must agree that this happens to many), you need to use only those staples that are recommended by the stapler manufacturer.
A mechanical stapler allows you to nail plastic panels, lining clamps, fabric to furniture, wooden or plastic surfaces.
There are three types of staplers: mechanical, electrical and pneumatic.
Mechanical staplers are affordable, compact, lightweight, and easy to maneuver. In the following, we will only talk about them.
How to choose a stapler?
In short, it is undesirable to buy the cheapest options, as well as plastic models. The metal tool is more powerful and more reliable.
Choose professional models that have an adjusting screw (lamb) at the top. It helps to regulate the force with which the tool will punch through the material.
Many people forget
Before working, adjust the adjusting screw according to the material of the surface to be worked on.
If it's a hard plywood, it will need a lot of punching through the material, so it's worth setting a lot of force. If it is a loose surface, the force must be reduced so as not to break through the fabric, or for example the pvc panel that you are targeting.
During operation, it is recommended to press the lever with one hand, and press the adjusting screw with the thumb of the other hand. Then the return will be minimal and the load will be distributed evenly in the stapler. You will be able to hammer in the brackets much better.
How to load staples into the receiver
The design of all mechanical hammers is almost the same. There is a handle-lever, due to which the pressure occurs, and at the bottom of the stapler there is a metal plate that opens the receiver. Here we have to load the brackets.
Before buying brackets at a hardware store, you need to find out what size is right for your machine.
How to fill a construction stapler
As a rule, the size and type of suitable staples are indicated on its body.
For example, on the body of our stapler, the width is 12 mm and the depth is 6-14 mm. This means that you will only be able to charge staples from that range.
Smaller or larger brackets will not fit the receiver. The size of the staples in millimeters is also indicated on their packaging.
To fill the shells into the stapler, you need to open the metal plate on the back surface.
To do this, you need to take it with your thumb and forefinger on both sides, then pull it towards you and slightly down. Thus, we wring out the metal tab on the back of the plate, and pull out a metal spring, similar to the one in a regular stationery stapler.
If there are still staples left in your stapler, they will fall out after you pull out the spring. If they are not there, then it is time to put new ones for further work.
Staples are inserted into the receiver (hole in the position of the letter "P"). Next, we insert the spring back, closing the metal foot. That's it, the tool is loaded and ready to go!
How many shells will fit
Now a little about how many shells fit in the stapler. Staples are sold in small rows. The row can be divided into several parts independently, slightly breaking it with your hands.
1-1.5 rows are loaded into the tool. 2 rows rarely fit in the receiver, so if there is a lot of work to be done, it is better to prepare halves of the rows before starting work.
What to do if the bracket is stuck
It is worth noting another very important point that will help you in your work. It happens that the brackets are bent and stuck in the exit hole. They cannot be hammered into the surface and cannot be pulled out by hand.
In this case, we need to pull out the feed magazine completely.
This possibility exists for almost all professional staplers.
First you have to repeat the opening of the metal plate and pull out the spring.
In this way, you will pull out the entire feed magazine that was in the tool.
You will see a jammed bracket, which is now easy to pull out with your hands.
Assembling the stapler back is not difficult: the entire pulled out block returns to its place with a push. When you do this, you should hear a click. After that, do not forget to put the spring in place.
More than just brackets
Some staplers can work not only with staples, but also with carnations of various shapes. The designations with which the stapler works are indicated on its body or in the instructions.
Carnations are tucked into the stapler in the same way with staples, but you need to be careful after pulling out the spring. A number of carnations must be loaded along one of the outer faces of the letter "P", and not inside this very letter!
If you want it to give out two nails at once side by side when working with a stapler, the second row is loaded along the second outer edge. Next, the spring is inserted and the stapler closes.
A stapler (in translation from English “stapler”) is a necessary thing in everyday life and at work. Stationery stapler is designed for fastening sheets and files. There are five types of stapler: manual, manual office, desktop horizontal or vertical, stitching, typographic. They all differ, before each in the number of sheets that can be stitched at a time.
You will need
- - stapler;
- - brackets.
Instruction
1. Determine what type of stapler you have. To do this, see how many sheets you can flash at a time. The most primitive in terms of device are pocket staplers. They are prepared for stapling up to 10 sheets. Manual office ones have a special recess on the fingers and allow you to fasten up to 30 sheets. Desktop horizontal or vertical ones have a rubber or plastic sole, they sew up to 50 sheets. In booklets, it is allowed to fasten up to 150 sheets, and typographic ones, which have a maximum depth of stitching, connect up to 250 sheets at a time. The specificity of stapling with a stapler is through fastening, which you carry out using a metal staple. The staple pierces the sheets to be stapled through, and its ends rest against the plate located at the end of the other side of the stapler.
2. Before charging the stapler, determine the size of the staples, the one that is suitable for it. Staples (which are also called paper clips) come in several types: No. 10, 26/8, 26/6, 24/8, 24/6. These numbers are written on the packaging. Staples must be packed in carton boxes 500, 1000 or 2000 pieces. Which of the above will suit your stapler, you will find out by looking at its packaging.
3. In order to load the stapler with the selected staples, bend its cover. It is connected by a spring to a plastic element, the one that presses the staples to the opposite edge of the metal groove, into the one that the staples are placed. Opening the cover will pull the spring along with it, and, consequently, the plastic element, thus freeing up space for new brackets.
4. Take one section of staples and place them in the metal groove with the ends down. Close the lid and click the stapler once to sample. If a bracket with concave ends inward fell out of it, then you did everything right, but if this did not happen, or the bracket bent abnormally, then repeat the procedure, or change the stapler.
