"TK Nord Santekhmontazh" LLC, the official dealer of Wavin, offers PVC and HDPE pressure pipes.
PVC is bell-shaped Wavin pressure pipe Sigma, available in PN 6 and PN No. 10 pressures.
HDPE is Wavin polyethylene pipes and also Wavin pressure pipes Quick Stream.
Vavin PVC pressure pipes and fittings are produced in the range of standard sizes from 63 to 400 mm.
In addition, the official wavin dealer offers a complete range of fittings: couplings, tees, bends, flanges. How Wavin pressure pipes and the fittings are supplied with fixed rubber sealing rings, which are installed and lubricated at the Wavin factory. To prevent contamination, all pipes and fittings are closed at the ends with red caps - for wavin sigma pressure pipes of class PN 6, blue - for wavi pressure pipes n and PN 10 class fittings.
Wavin PVC pressure pipes
Wavin PVC pressure pipes are made of unplasticized polyvinyl chloride (nPVC) and have the following advantages:
Size wavin pressure pipes from 63 to 400 mm for pressure classes PN 6 and PN 10.
Low weight pressure pipes wavin.
High strength wavin pressure pipes.
Corrosion resistance.
Good hydraulic properties.
Low force required to connect wavin pressure pipes.
No need to chamfer ends.
Elastic connections with rubber seals.
Installed motionlessly lip rubber seals "Vaviseif".
Long life silicone grease pre-applied to the rubber rings.
Color coded stubs.
No need for care and maintenance.
Sealing systems "Vavisafe" (Wavisafe)
The sealing system "Vavisafe" is designed to connect the socket of pressure pipes and the spigot ends of the entire wide range of Vavin products and consists of fixed rubber rings installed at the factory, on which a special silicone lubricant is applied during installation, and an effective fastening system. Both the rubber ring and the fastening system were developed at the Wavin plant in Hummel.
Since plastics are capable of elastic interaction with the surrounding soil, pressure PVC pipes mainly used for underground pipelines. Due to the presence of tensile-resistant flanges and fittings, these products can also be used for internal systems.
Polyethylene (PE) pipes
PE Vavin pressure pipes made of light blue material PE 80 and dark blue material PE 100. PE floor pipes have the following advantages:
Standard sizes of pressure pipes from 16 to 450 mm for pressure classes PN 6.3, PN 10, PN 16.
Color coding of pressure pipes:
in red - for class PN 6.3
black - for class PN 10
green - for class PN 16
Possibility to easily determine which of the pipelines in the trench is a drinking water pipeline - thanks to the blue color
Suitability for both butt welding with contact heating, and for welding with heating from a built-in electric spiral
Water vapor permeation resistance and good chemical resistance
Low weight wavin HDPE pressure pipes
High strength HDPE pressure pipes wavin
Use of tensile-resistant flanges
Flexibility of wavin pressure pipes
Corrosion resistance
Good hydraulic properties wavin pressure pipes
No need for care and maintenance
PE 100 is a further development of PE 80. Research into new raw materials has led to the development of higher performance polyethylene (PE) pressure pipes with thinner walls, which increases flow capacity, reduces pressure pipe welding times and reduces weight. The strength properties of the PE 100 material are more effective with large product sizes. Therefore, PE 80 is still used for smaller products.
PE Wavin pressure pipes particularly suitable for pipeline rehabilitation without overburdening, while the highly flexible PE 80 products are particularly advantageous when laying in difficult conditions, such as underwater pipelines (in seas and lakes).
PE pressure pipes can also be used for internal systems. Vavin can manufacture them by shaping or welding into products for various special applications.
Wavin Quick Stream Pressure Pipes
Wavin Quick Stream pressure pipes - pressure drainage system for removing water from roofs. The operation of the system is based on the gravitational-vacuum principle, i.e. creating a vacuum under the action of the gravity of the water. With moderate precipitation, the system works like a traditional gravity-fed system. As the intensity of the rain increases. the risers are completely filled with water, and the system goes into pressure mode. In this case, a rarefaction occurs in the riser, which entrains water from the pipeline. This creates an additional suction of rainwater through funnels equipped with air cutters. Due to the high flow rate and the resulting vacuum, there is a significant increase in productivity with a significant reduction in pipeline diameters compared to a conventional system.
The pressure system includes:
Gutter funnels - the model depends on the design of the roof and roofing material. Funnel diameters from 40 to 125mm
Wavin pressure pipes and fittings made of polyethylene (PE). Diameter range from 40 to 315mm.
Mounting system - steel mounting rail, clamps, clamps.
To calculate the system, special software is used, calculations are made only by specialists of TK Nord Santekhmontazh LLC
As a result of calculations, axonometric drawings are created indicating the lengths of pipeline sections and their diameters, as well as the specification of the materials used (pipes, fittings, fasteners, funnels).
Changing the initial data of the project may affect the correctness of the results obtained, and consequently, the performance of the system. In this regard, any changes must be agreed in a timely manner with the specialists of TK Nord Santekhmontazh LLC using the Quick Stream system.
NASHORN is a manufacturer of double layer drainage pipes. Water drainage from buildings and structures is one of the most important elements in the design of a building, because an improperly installed drainage system can eventually destroy the entire house. Therefore, the issue of water drainage must be approached with all seriousness. Gutters, gutters, and proper roofing can't do the job completely. A horizontal drainage system will help with this. Drainage pipes are part of the horizontal drainage design, the function of which is to receive and remove moisture. At different times, a variety of materials are used for the manufacture of pipes, such as ceramics, asbestos cement, concrete, reinforced concrete, and wood. Currently, the most convenient and modern material is polyethylene. Recently, polyethylene has been most often used, since it has a number of advantages: resistance to physical and chemical attack, corrosion, durability, ease of transportation, structural uniformity, strength, ease of system development, low price and a wide temperature range of use. Pipes are of two types: single-layer and double-layer. Single-layer ribs inside and out, double-layer ones are smooth inside, which facilitates the passage of water, and can be laid to a depth of more than two meters. They also differ in the degree of perforation: partial or complete perforation. Partial for hard ground, full for soft ground. Drainage pipes are available in two colors: green and black. Green ones are made with geotextile filters, black ones without…
Drainage wells, sewer wells, fittings.
-
Drainage wells are large diameter corrugated pipes. Designed to clean the drainage system, monitor its operation and serve as a water intake when draining the territory.
Drainage well bottoms, drainage well bottom, well cover-bottom, inspection chambers
Couplings for wells plastic with a rubber ring.
Accessories for surface drainage.
-
The scope of plastic pipes for external sewerage is the passage of wastewater from buildings and structures in the ground to drain wells. Plastic pipes for external sewerage are made of polyvinyl chloride - plastic, a thermoplastic polymer of vinyl chloride. PVC pipes can transport various liquids under pressure, heated up to 40°, and by gravity - up to 50°. It should be said about the maximum temperature, it is 60 °, at which PVC softens. Pipes made of polyvinyl chloride (PVC) are very durable and practically not subject to abrasion, do not scratch and are resistant to aggressive chemical influences (special additives make them very resistant to any chemistry), and therefore PVC pipes, at present, are widely used in internal and external sewer networks. Individual elements of the sewer system are quickly, easily and conveniently assembled. Reliable and tight reliable connection of pipes is ensured by the presence of a special chamfer (bell) and a special rubber sealing ring.
Plastic plugs for external sewerage are a type of fittings, designed to block gaps in pipelines. Are applied to closing of pipes, protection of ends of pipes. There are various purposes, shapes and colors. It is used for installation work in sewer systems, as well as in hot and cold water supply systems in industrial and residential buildings and structures. Our product catalog includes Wavin and Pestan drain plugs. You can buy from us plastic plugs for sewerage, providing high tightness. The excellent characteristics of plastic plugs allow you to securely fix it on the pipe.
The coupling for pipes of the external sewerage are intended for connection of pipes among themselves. Due to their design, couplings for external sewage pipes ensure the tightness and durability of the pipe connection. Pipes for external sewerage are laid in the ground, which imposes special requirements on couplings for pipes of this type. Their strength characteristics should be higher than for other types of couplings. Such a margin of safety is provided by the manufacturers Wavin and Politek. The scope of application of couplings for pipes of external sewerage also includes repair, repair of small breakdowns and leaks in pipes, as well as docking of various types of pipes (transitional couplings).
Elbows for external sewage pipelines are designed to connect pipes at a given angle. In the construction of sewer systems, one cannot do without turning pipes and, accordingly, fluid flow. In construction, there are no non-standard pipes, bent and not typified. Elbows for pipelines are designed to ensure the connection and turn of pipes in the right direction and significantly reduce the time spent on design and installation, as well as the cost of work.
Transitions for pipes of external sewerage - fittings designed to make connections between pipes of different diameters. Wavin external sewage pipe adapters are made of durable and anti-corrosion PVC (polyvinyl chloride) material. Transitions provide high tightness of the connection due to the presence of rubber rings at the junction of NASHORN plastic pipes with a transition for external sewage pipes.
Sewer inspections are designed for installation of non-pressure sewer pipes in internal and external sewer systems. A sewer revision is a fitting that provides access to sewer pipes for the purpose of checking or cleaning them. Wawin and Politek sewer revisions are made of PVC (polyvinyl chloride), have high strength and tightness, are resistant to aggressive media, as well as various oily liquids and acids. The tightness of the connection of pipes with a sewer revision is ensured by the presence of rubber sealing rings and excellent workmanship. The revision has a red-brick (orange) color, it does not need to be painted and pre-prepared before starting installation work.
Tees for external sewerage are used when there is a need for branching sewer networks. Tees are divided into equal and transitional. Equal bore tees have the same neck and body diameters. Reducing tees differ from conventional adapters in that they have different diameters of the body and neck of the product. The scope of application of transitional tees is a branch of pipelines of smaller diameter from the central highways. Shaped products - tees, are subjected to significantly greater loads compared to pipes. Therefore, they are subject to increased requirements for strength and thermal characteristics. Wavin and Politek tees, presented in our product catalog, meet all the requirements for such products and can be used in sewer systems of any complexity. Tees comply with GOST of the Russian Federation and all regulatory requirements applicable in the CIS and EU countries. PVC sewer tees are made using mold casting and gas cutting technology with welding and stamping. Polyvinyl chloride tees are the most favorable in terms of price / quality ratio: they are lighter, easier to install, do not require any preparatory work. For more than 5 years, PVC tees have been in the first place in terms of use in installation
A check valve is a device that allows the flow of liquid through a pipeline in only one direction, automatically closing when the direction of flow changes. It is used in various industrial areas, including the construction of country houses, cottages and other buildings and structures. Wavin and MPlast check valves are of high quality, low weight, anti-corrosion properties, are not affected by aggressive chemical compounds, and are easy to install. For tight connection with plastic pipes, the check valve has sealing rubber rings that perfectly cope with loads. The check valve itself is made of polyvinyl chloride (PVC), which increases its service life up to 50 years.
Geotextile Typar of the American company DuPont. The product is certified. Our site contains articles about the manufacturing technology, characteristics and history of the Dupont Typar Geosynthetics division.
Water drainage from buildings and structures is one of the most important elements in the design of a building, because an improperly installed drainage system can eventually destroy the entire house. Therefore, the issue of water drainage must be approached with all seriousness. Gutters, gutters, and proper roofing can't do the job completely. A horizontal drainage system will help with this. Drainage pipes are part of the horizontal drainage design, the function of which is to receive and remove moisture. At different times, a variety of materials are used for the manufacture of pipes, such as ceramics, asbestos cement, concrete, reinforced concrete, and wood. Currently, the most convenient and modern material is polyethylene. Recently, polyethylene has been most often used, since it has a number of advantages: resistance to physical and chemical attack, corrosion, durability, ease of transportation, structural uniformity, strength, ease of system development, low price and a wide temperature range of use. Pipes are of two types: single-layer and double-layer. Single-layer ribs inside and out, double-layer ones are smooth inside, which facilitates the passage of water, and can be laid to a depth of more than two meters. They also differ in the degree of perforation: partial or complete perforation. Partial for hard ground, full for soft ground. Drainage pipes are available in two colors: green and black. Green ones are made with geotextile filters, black ones - without a filter. Geotextile winding serves as a filter, preventing…
NASHORN is a manufacturer of double layer drainage pipes. Water drainage from buildings and structures is one of the most important elements in the design of a building, because an improperly installed drainage system can eventually destroy the entire house. Therefore, the issue of water drainage must be approached with all seriousness. Gutters, gutters, and proper roofing can't do the job completely. A horizontal drainage system will help with this. Drainage pipes are part of the horizontal drainage design, the function of which is to receive and remove moisture. At different times, a variety of materials are used for the manufacture of pipes, such as ceramics, asbestos cement, concrete, reinforced concrete, and wood. Currently, the most convenient and modern material is polyethylene. Recently, polyethylene has been most often used, since it has a number of advantages: resistance to physical and chemical attack, corrosion, durability, ease of transportation, structural uniformity, strength, ease of system development, low price and a wide temperature range of use. Pipes are of two types: single-layer and double-layer. Single-layer ribs inside and out, double-layer ones are smooth inside, which facilitates the passage of water, and can be laid to a depth of more than two meters. They also differ in the degree of perforation: partial or complete perforation. Partial for hard ground, full for soft ground. Drainage pipes are available in two colors: green and black. Green ones are made with geotextile filters, black ones without…
NASHORN is a manufacturer of double layer drainage pipes. Water drainage from buildings and structures is one of the most important elements in the design of a building, because an improperly installed drainage system can eventually destroy the entire house. Therefore, the issue of water drainage must be approached with all seriousness. Gutters, gutters, and proper roofing can't do the job completely. A horizontal drainage system will help with this. Drainage pipes are part of the horizontal drainage design, the function of which is to receive and remove moisture. At different times, a variety of materials are used for the manufacture of pipes, such as ceramics, asbestos cement, concrete, reinforced concrete, and wood. Currently, the most convenient and modern material is polyethylene. Recently, polyethylene has been most often used, since it has a number of advantages: resistance to physical and chemical attack, corrosion, durability, ease of transportation, structural uniformity, strength, ease of system development, low price and a wide temperature range of use. Pipes are of two types: single-layer and double-layer. Single-layer ribs inside and out, double-layer ones are smooth inside, which facilitates the passage of water, and can be laid to a depth of more than two meters. They also differ in the degree of perforation: partial or complete perforation. Partial for hard ground, full for soft ground. Drainage pipes are available in two colors: green and black. Green ones are made with geotextile filters, black ones without…
NASHORN is a manufacturer of drainage pipes with a geotextile filter. drainage pipes NASHORN Drainage of buildings and structures is one of the most important elements in the design of a building, because an improperly installed drainage system can eventually destroy the entire house. Therefore, the issue of water drainage must be approached with all seriousness. Gutters, gutters, and proper roofing can't do the job completely. A horizontal drainage system will help with this. Drainage pipes are part of the horizontal drainage design, the function of which is to receive and remove moisture. At different times, a variety of materials are used for the manufacture of pipes, such as ceramics, asbestos cement, concrete, reinforced concrete, and wood. Currently, the most convenient and modern material is polyethylene. Recently, polyethylene has been most often used, since it has a number of advantages: resistance to physical and chemical attack, corrosion, durability, ease of transportation, structural uniformity, strength, ease of system development, low price and a wide temperature range of use. Pipes are of two types: single-layer and double-layer. Single-layer ribs inside and out, double-layer ones are smooth inside, which facilitates the passage of water, and can be laid to a depth of more than two meters. They also differ in the degree of perforation: partial or complete perforation. Partial for hard ground, full for soft ground. Drainage pipes are available in two colors: green and black. Greens are made...
This page is not found.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Morbi non ligula consectetur, consequat arcu quis, aliquet erat. Nullam a massa venenatis, commodo velit. Aenean nec facilisis dui, sed molestie metus.
Address
Factory and warehouse address: Klimovsk, st. Zavodskaya d. 2
Postal address: 142181, Moscow region, Klimovsk, Zavodskaya st., 2, PO box 15
Office: Ilyinskoye highway, village Golyevo, st. Tsentralnaya, 3, directions
Menu:
1. General characteristics
Pipes of large diameters are intended for use in industrial purposes, small ones - in private households. When laying an electrical, telephone, television or computer network, use either smooth products that are a good protection against possible damage.
PVC risers for sewer systems are connected using sockets with rubber o-rings.
This method of installation is simple, reliable, fast. In addition, this method is quite economical in terms of financial costs, which are minimized.
3. The main criteria for choosing pvc risers
The process of production and installation of PVC risers must strictly comply with the technical regulations.
It means that:
- operational specifications must be confirmed by preliminary tests;
- the process of packaging, moving PVC products must meet the technical requirements;
- each pipe must be marked in accordance with the state standard.
The marking of any pipe is its face, a passport, which contains all the necessary data about it.
In particular, the character set speaks of:
- wall thickness;
- type of polyvinyl chloride;
- outer diameter;
- state standard;
- size ratio;
- appointment;
- the form of a bell.
4. Assortment: classification by type, application
The assortment of pvc socket pipes is determined.
4.1. Classification
Products are made smooth and corrugated (they can be one- or two-layer: with a smooth inner and corrugated outer layer).
Depending on the purpose, smooth pipes are:
- , with the help of which they equip the external and internal systems;
Depending on the conditions of the transport media, risers can be:
- pressure ones, through which the movement of the medium is allowed in the presence of high pressures;
- non-pressure, which carry out the transportation of the medium without the presence of pressure;
- for sparse media.
From where the pipeline system is located, risers can be:
- outdoor;
- internal.
4.2. Application
Most often, water inlets and sewer networks of significant sections are completed with external risers. The internal version of the products is intended only for transporting water runoff and other liquids from apartments or private houses.
5. Dependence of the scope of application on the appearance and color
They differ in versatility. They can be one- and two-layer (the outer layer is corrugated, the inner one is smooth). Corrugated material used for the production of pipes is much cheaper than metal.
Corresponding corrugated products are also relatively cheap.
If the laying of the system is open, a black corrugated PVC pipe is used, and if hidden, a smooth version of the risers is used. For such purposes, a sewer bell-shaped PVC pipe with a conditional bore of dn32, dn40, dn50 and more is often used, the price of which depends on the material of manufacture, the manufacturer, and the delivery batch. Plastic pipes come in different colors. If the riser is gray, then it can only be used indoors.
Blue and white counterparts provide reliable well casing.
An orange thick-walled PVC pipe is used in a gravity-flow type external sewage system. A structure with such elements can be laid to a depth of 7-8 meters.
Transparent PVC is used for the production of transparent risers with a wall thickness of 0.5 mm - 5 mm, a diameter of 3 mm - 14 mm. Such designs are able to fully function in the temperature range from -30 to +80 degrees Celsius. Due to transparency, the liquid that moves inside it is visible in the pipeline. This significant advantage provides the ability to fully control the transportation process.
Pipelines mounted from transparent risers can:
- move drinking, distilled, sea water;
- transport cooling drinks, dairy products, carbonated and mineral water, juices, wines, strong alcoholic drinks, vinegar, vegetable oils.
They also complete freezers, water supply systems.
6. Socket risers for sewerage
6.1. What are they made from
PVC pressure socket pipes, as well as fittings, are produced with a diameter of 90-630 mm and can be used in lines with maximum operating pressures: 600 kPa, 1000 kPa, 1250 kPa, 1600 kPa. The main substance for the production of products is (PVC, pvc-). For sewer pipelines, pressure structures with elongated sockets and bare ends are used.
6.2. Properties
PVC bell risers are different:
- high quality and durability of the material;
- the possibility of connecting products from various materials;
- ideal hydraulic properties;
- light weight;
- a long period of operation;
- good throughput;
- increased resistance to corrosion;
- toxicological and bacteriological safety;
- high tightness of the structure;
- the possibility of mounting with various shut-off and connecting fittings.
Buying such a socket pvc pipe means significantly saving money. The fact is that the laying of pvc socket pipes can be done by two people. Given this factor, all installation work can be easily done by hand, since this does not require special construction equipment or heavy physical effort.
6.3. Benefits and Uses
Bell-type (abbreviation PVC) can operate in conditions with high pressures and sudden temperature changes. Risers are characterized by increased resistance to moisture, alkalis and salts, acids, gasoline, alcohol, grease, sewage and other liquids. The service life of their PVC structures is five to six decades. Products are allowed to operate at a maximum temperature of 60⁰С, which is slightly less than the same indicator for polyethylene pipes (80⁰С).
7. Connection of bell-shaped pressure PVC risers with glue
The number of types of connections for socket risers has recently been replenished with a novelty: connection with glue. It turned out that the adhesive connection makes PVC pressure socket pipes, the whole structures of them more reliable and durable in operation.
7.1. Benefits of bonding
These routes are different:
- durability of functioning;
- reliability;
- resistance to corrosion processes;
- the possibility of laying pipelines, including water pipes, at great depths underground, since such systems are very durable;
- low weight of the structure, which helps to reduce transportation costs and simplify the installation process;
- ease of installation;
- resistance to high temperatures (the structure can begin to melt at a temperature of 190-210⁰С, which is more than in polyethylene or polypropylene);
- thermal conductivity, the numerical value of which is close to that of thermal insulation materials;
- environmental friendliness, due to which the products have found application in the installation of pipelines for drinking water;
- excellent throughput as the parts have good hydraulic properties.
They are able to fully function with working pressures from 600 kPa to 2,000 kPa.
Therefore, without pipes on an adhesive joint, they cannot work:
- industrial pipelines;
- modern irrigation systems with drip irrigation.
Due to a number of positive qualities, the most complex pipe structures can be built from such risers.
7.2. Mounting process
Socket pvc pipes build up one on top of the other, fixing the junction at the same time. During the installation of pipelines, adhesive, bends, and other connecting parts are used, just as cast or segment fittings are used when assembling lines from polyethylene pipes. Unidelta clamp fittings are also excellent for connecting polyethylene pipes. Their main advantage, in comparison with other analogues: reliability and speed of assembly of the pipeline. Fittings of the Italian company unidelta occupy a leading position in the market of modern shaped fittings.
For the production of fittings, as well as the risers themselves, mixtures with PVC suspension, stabilizing agents, dyes, and pipe fillers are used.
8. Application of Wavin pipes
Unplasticized PVC (classes N and S) is the raw material for Wavin pipes.
For unplasticized polyvinyl chloride, the following properties are characteristic:
- increased resistance to acids, alkalis, salts;
- sufficient hardness;
- shape retention at high temperatures.
Plus, the material is characterized by the presence of extraordinary chemical resistance. Pipes pvc socket wavin easily tolerate the effects of alcohols, aliphatic hydrocarbons, gasoline, oils and other chemically aggressive substances.
For thin-walled N class risers, laying to a depth of 6 m, but not less than 60 cm, is recommended. Class S (thick-walled) products can be laid in systems passing under roads or other places where traffic is possible, on depth of 80 cm or more.
Thanks to the socket, Wavin pipes are connected in a way of building one on top of the other. For sealing, rubber rings are used, which are placed in the internal grooves. Connections in this way ensure the tightness of pipelines at 100%.
From the pipes of the Dutch company Wavin, sewer lines and storm drains are mounted.
The company is one of the largest manufacturers of polymer installation systems. The history of the concern began in 1955, when the world's first plant for the production of large-diameter PVC water pipes was built in the Dutch city of Zwolle. Adhering to the policy of high standards, we offer reliable products of this company for the creation of various systems.
Technopipe LLC sells branded integrated systems made of Wavin pipes in the Moscow region wholesale, and also supplies individual pipeline elements for retail.
You can order Wavin pipes from us
Application of Wavin pipes
The company positions itself as a manufacturer of effective solutions for basic life needs. For almost every application, our Wavin pipe catalog contains products that are optimally suited to the solution of a particular task.
The company proposes to solve the problem of delivering clean drinking water with the help of safe outdoor water supply networks made of polyethylene and PVC. Products are designed for various conditions and installation methods, including trenchless installation. For the installation of internal water supply networks, Wavin pipes and fittings from the Ekoplastik series, as well as Tigrius metal-plastic materials, are on sale.
A number of efficient solutions have been developed in the field of storm water drainage. X-Stream double-walled corrugated piping systems, smooth and PVC drainage systems are available to order. The products have a low cost and a wide range of uses - from the protection of road surfaces to the drainage of airfields and agricultural fields.
The price of Wavin pipes varies depending on the diametrical dimensions, physical and chemical parameters and technical characteristics of the material.
For the removal of domestic wastewater, it is proposed to use both traditional plastic products and new, low-noise systems. If the requirements for noise level are high, the best solution would be to buy cheap Vavin pipes (see photo) from the Asto series.
Reliability and durability of external sewer networks is ensured by pressure and non-pressure smooth-walled pipes made of PVC. In addition, the company's arsenal includes double-wall corrugated plastic pipes Vavin X-Stream. Together with them, various connection elements are supplied: bends, tees, crosses, adapters for Vavin pipes. Prices for these products are listed separately. Vavin pipes (see the catalog on this page), designed for heating systems, are presented in the Tigrius (metal-plastic) and Ekoplastik series. The products are characterized by low cost of materials, quick installation and reliable connections.
| PVC internal sewerage WAVIN OPTIMA - minimum order 30 thousand rubles | ||||
|---|---|---|---|---|
| Name | Catalog number | Dimensions Dy, mm | Multiplicity of packaging, pcs. | Price**, euro/pc. |
| PVC pipe with socket and sealing ring | 24326029 | 50x2.5x250 | 60 | 0.93 |
| 24326032 | 50x2.5x315 | 60 | 0.97 | |
| 24326035 | 50x2.5x500 | 60 | 1.35 | |
| 24326041 | 50x2.5x1000 | 40 | 2.43 | |
| 24326044 | 50x2.5x2000 | 20 | 4.58 | |
| 24337065 | 75x2.5x250 | 40 | 1.54 | |
| 24337069 | 75x2.5x315 | 40 | 1.23 | |
| 24337072 | 75x2.5x500 | 40 | 2.14 | |
| 24337078 | 75x2.5x1000 | 20 | 3.31 | |
| 24337081 | 75x2.5x2000 | 20 | 6.05 | |
| 24346084 | 110x2.6x250 | 30 | 1.98 | |
| 24346087 | 110x2.6x315 | 30 | 2.11 | |
| 24346090 | 110x2.6x500 | 30 | 2.97 | |
| 24346096 | 110x2.6x1000 | 20 | 5.06 | |
| 24346099 | 110x2.6x2000 | 10 | 9.16 | |
| Pressure drainage system Quick Stream - minimum order 30 thousand rubles | ||||
|---|---|---|---|---|
| Name | Catalog number | Dimensions, mm | Multiplicity of packaging | Price**, euro/pc. |
| PE pipe, price is for 1 m, standard length 5000 mm | 26523201 | 40 | 520 | 3.25 |
| 26526201 | 50 | 700 | 3.52 | |
| 26528201 | 56 | 580 | 3.77 | |
| 26534201 | 63 | 240 | 4.36 | |
| 26537201 | 75 | 340 | 4.97 | |
| 26540201 | 90 | 265 | 6.65 | |
| 26546201 | 110 | 215 | 10.88 | |
| 26548201 | 125 | 190 | 12.11 | |
| 26556201 | 160 | 100 | 21.14 | |
| 26560201 | 200 | 70 | 26.21 | |
| 26564201 | 250 | 55 | 45.38 | |
| 26570201 | 315 | 30 | 71.61 | |
| EXTERNAL SEWER SYSTEM X-Stream - minimum order 30 thousand rubles | ||||
|---|---|---|---|---|
| Name | Catalog number | Dimensions, mm | Multiplicity of packaging, pcs. | Price**, euro/pc. |
| PP double wall socket pipe Class S | 23142006 | 100x6000 | 1 | 42.84 |
| 23154006 | 150x6000 | 24 | 93.52 | |
| 23160006 | 200x6000 | 25 | 84.40 | |
| 23164006 | 250x6000 | 16 | 136.64 | |
| 23168006 | 300x6000 | 9 | 173.20 | |
| 23176006 | 400x6000 | 6 | 281.33 | |
| 23180006 | 450x6000 | 4 | 402.67 | |
| 23182006 | 500x6000 | 2 | 488.84 | |
| 23186006 | 600x6000 | 3 | 687.56 | |
| 23194006 | 800x6000 | 2 | 1228.68 | |
| PP double wall socketless pipe Class S | 23160016 | 200x6000 | 25 | 73.66 |
| 23164016 | 250x6000 | 16 | 123.30 | |
| 23168016 | 300x6000 | 9 | 158.47 | |
| 23176016 | 400x6000 | 6 | 247.06 | |
| 23180016 | 450x6000 | 4 | 344.73 | |
| 23182016 | 500x6000 | 2 | 450.84 | |
| 23186016 | 600x6000 | 3 | 575.73 | |
| 23194016 | 800x6000 | 2 | 1020.92 | |
| WAVIN ASTO - Noise-absorbing internal sewage system - minimum order 30 thousand rubles | ||||
|---|---|---|---|---|
| Name | Catalog number | Dimensions Dy, mm | Dimensions DN, mm | Price**, euro/piece |
| PP pipe without socket | 24129050 | 58x4.0x3000 | 56x4.0x3000 | 16.61 |
| 24138055 | 78x4.5x3000 | 70x4.5x3000 | 21.16 | |
| 24146070 | 110x5.3x3000 | 100x5.3x3000 | 34.29 | |
| 24151075 | 135x5.3x3000 | 125x5.3x3000 | 43.31 | |
| 24156080 | 160x5.3x3000 | 150x5.3x3000 | 51.62 | |
| 24160085 | 200x6.2x3000 | 200x6.2x3000 | 78.89 | |
| PP pipe socket | 24129090 | 58x150 | 56x150 | 3.73 |
| 24129095 | 58x250 | 56x250 | 4.24 | |
| 24129100 | 58x500 | 56x500 | 3.43 | |
| 24129105 | 58x1000 | 56x1000 | 6.11 | |
| 24129110 | 58x2000 | 56x2000 | 10.63 | |
| 24138115 | 78x150 | 70x150 | 4.33 | |
| 24138120 | 78x250 | 70x250 | 5.01 | |
| 24138125 | 78x500 | 70x500 | 5.03 | |
| 24138130 | 78x1000 | 70x1000 | 9.08 | |
| 24138135 | 78x2000 | 70x2000 | 15.73 | |
| 24146160 | 110x150 | 100x150 | 5.06 | |
| 24146165 | 110x250 | 100x250 | 6.73 | |
| 24146170 | 110x500 | 100x500 | 8.20 | |
| 24146175 | 110x1000 | 100x1000 | 14.48 | |
| 24146180 | 110x2000 | 100x2000 | 25.40 | |
| 24151185 | 135X150 | 125X150 | 8.88 | |
| 24156190 | 160X150 | 150X150 | 8.15 | |
| Metal-plastic system WAVIN FUTURE K-1 (Alupex) - minimum order 30 thousand rubles | ||||
|---|---|---|---|---|
| Name | Catalog number | Dimensions, mm | Multiplicity of packaging, pcs. | Price**, euro/pc. |
| PEXc/Al/PE pipe (coiled) | 25504015 | 16x2.0 | 200 m | 1.66 |
| 25508023 | 20x2.25 | 100 m | 2.73 | |
| 25512031 | 25x2.5 | 50 m | 4.09 | |
| 25520039 | 32x3.0 | 50 m | 6.77 | |
| PEXc/Al/PE pipe (in lengths) | 25523047 | 40x4.0 (5m) | 5 | 15.04 |
| 25526055 | 50x4.5 (5m) | 5 | 18.57 | |
| Protective pipe (in coils) | 25504063 | 25/21 | 50 m | 0.42 |
| 25508073 | 28/23 | 50 m | 0.78 | |
| 25512083 | 36/29 | 50 m | 1.92 | |
Production of Wavin plastic pipes
The concern's production facilities are located in different countries, however, they are united by a single policy aimed at product quality.
Naturally, in order to achieve high results, the company made every effort, adopting the best equipment, raw materials and a modern quality control system. Almost the entire range of products is made by extrusion and is designed for half a century of use.
Packaging and storage of Wavin pipes
Pipe segments of 500 mm each and up to 40 mm in diameter are packed in cardboard boxes or opaque bags. The rest of the material is packed in bundles with a wooden crate. Fittings, parts and valves are also supplied in boxes. The manufacturer recommends keeping the product in its packaging until use.
The storage area must be level, without sharp protrusions that could damage the product. In case of long-term storage in an open way, it is necessary to provide protection from direct sunlight.
Product Advantages
- high quality standards;
- development of new, unique products;
- duration of operation of systems;
- reliability of pipelines and connections;
- high performance;
- variety of connection elements and related materials;
- comprehensive supply of materials (pipes, wells, fittings) for entire systems;
- quick and easy installation;
- striving to create economical products.
Haven't decided where to buy a Wavin pipe? Trade House "Technopipe" will deliver the necessary materials to this company in time in any quantity. You can find out how much a Wavin pipe costs in Moscow by reading our price list. You can download or leave a request for the current price list of Wavin pipes here.
Advantages of Wavin pipes used in the private sector:
- safety for humans and the environment;
- the ability to install in difficult conditions;
- plastic.
They are used for water supply systems, domestic and storm drains, pumping stations, drainage structures.
