Do-it-yourself wooden do-it-yourself country shower with a dressing room. Do-it-yourself summer shower for a shower in the country: how to organize and connect the system. Naturally heated shower: video

Hot weather is a rarity in most of our country. On cold days, it is simply not possible to heat the water in the tank to the desired temperature. There are not many people who want to take an ice shower.

By country shower, most people mean a simple design with a barrel on the roof. Such a shower has the following disadvantages:

• water in the container blooms very quickly;
• there are constant problems with filling the barrel;
• it is impossible to maintain the desired water temperature.

To realize the idea, you need to familiarize yourself with the advice of craftsmen. A country shower will allow the family to comfortably take water procedures.

Mobile shower works according to the following principle. Any container is installed next to the device. It can be a bucket or a bowl. Warm water is poured into it. After that, the end of the hose is lowered into the container.

The device that pumps water into the shower looks like a rug. A hose with a watering can is connected to one end of the pump. Thus, you can get a stream of water that will flow while trampling on the rug. This option is convenient because the mobile shower can be used not only in the country. The device is useful for people who want to maintain hygiene during a hike. Even in such Spartan conditions, you can wash yourself. The advantage of such a shower is the ability to adjust the temperature of the water.

How to make a summer shower in the country with your own hands - to build a reliable structure, photos and sizes are carefully selected.

When building a stationary shower, the owner needs to decide where to take the water. If the site already has a semblance of a drain pit, then you can divert water directly there. But this is not the best solution, as many people use bacteria to process wastewater. An increase in humidity will have a negative effect on the rate of purification of the contaminated liquid.

In the process of building a shower room, it is best to make a separate drain hole. To strengthen the bottom of the pit, you can use broken bricks.

The hardest thing to strengthen a hole dug in sandy soil. Its walls will be eroded by sewage during operation. Therefore, it is necessary to sheathe the walls of the sandy recess with boards.

The owner can save money when building a shower at the expense of materials. For the erection of the soul, there is no need to erect. In the construction of the foundation, foundation blocks are most often used. They are set according to the level and the shower is raised 20 cm above ground level.

This height is enough so that the treated wood does not rot. When building a base, it is not necessary to use wood. You can weld a metal case and put it on paving slabs. If desired, you can strengthen the base by pouring it with concrete.

There are no specific standards regarding the framework. The shower cabin, as a rule, consists of several parts. In one compartment you can arrange a dressing room. In another room there is a water heater. Firewood can be used as fuel.

A room for storing inventory can be attached to the shower. If you are planning a lighter structure, then you can use the following option - instead of a door, hang a curtain. This will facilitate the construction and reduce the cost of construction. Be sure to consider the height of the people who will go to the shower. The optimal height should be 2.2 meters. The width of the structure must be at least 0.9 meters. In the manufacture of the frame, you can use not only metal, but also wood.

For the manufacture of a metal frame, it is desirable to use corners with a thickness of at least 4 millimeters. The width of the shelf depends on the load. The frame will hold the water tank. What if you plan to supply a 100 liter plastic container?

In this case, it is necessary to carry out the procedure for sheathing the shower cubicle on both sides with a special clapboard. This material is considered the most practical. It has an attractive appearance and is able to withstand a humid environment for a long time. But for this it is necessary to process the lining with a special solution.

To make a metal frame, you can use scraps of metal pipes. The wall thickness of the pipe must be at least 3 mm. Otherwise, the design of the shower may not withstand the load.

You can strengthen the frame with a crate. To do this, weld additional corners to the structure. In the absence of a welding machine, it can be fixed with bolts.

To build a shower in the country with your own hands, you need to calculate the volume of the tank. For a family of 4, you will have to put a barrel with a volume of 100 liters. For the manufacture of a wooden frame, you can buy a bar. The fastening of the bars is carried out according to the tenon-groove system.

Do-it-yourself summer shower for a summer residence can be built without the use of expensive materials.

The film is considered the cheapest material for shower wall cladding. The disadvantage of this option is that the service life is too short. In a year you will have to buy a new film. Therefore, summer residents prefer more reliable materials that can last several seasons.

It is better to give preference to fabrics with impregnation. This material is used for the manufacture of awnings and tents. When buying lumber, keep in mind that fresh lining cannot be used. The reason is that any lumber undergoes shrinkage.

During the drying process, the material loses its shape and former dimensions. This affects the quality of lumber. On its surface, various defects may appear that reduce strength. Warping and cracks are the most common flaws that have a negative impact on wooden structures. In a structure built from fresh lumber, gaps may appear in a year. Do-it-yourself shower in the country, drawings, dimensions, photos are of interest to many users who wish to warn themselves against these shortcomings.

For sheathing, you can use the profiled sheet left after the construction of the fence.

Polycarbonate is a transparent material that will decorate any shower room. Do not allow cracks to appear, as dust and moisture will get into them. This is a favorable environment for the reproduction of algae. Gradually, the walls of the polycarbonate will be completely covered with greenish vegetation.

When building a shower, a ventilation system must be provided. Constant moisture can cause wood to rot. A fungus appears on the walls, destroying the structure.

Any container is suitable as a shower tank. It can be a metal or plastic barrel. However, plastic barrels heat water worse. For the middle band, this can be critical, since the water needs to be heated.

Ice water is unlikely to please the owner of a country house. Although plastic containers are cheaper than metal ones. But this is the only advantage of such barrels. It is best to install metal containers. Not only are they easier to install. The owners do not have to think about how to fix the metal barrel. In such a container, water will heat up much faster. The process of heating water can be accelerated by painting the container black. The disadvantage of this option is the appearance of rust.

People are wondering how to make a shower in the country with their own hands and how to choose the right water tank, when studying a photo of a building, you can decide on the right choice of design and water tank.

Sometimes a septic tank is installed directly under the shower. In this case, the boards are laid with a gap of 3 mm. Water will flow down and fall directly into the drain hole. In sandy soil, water will not stagnate.

But for clay soil, this version of the septic tank is not suitable. To organize a normal drain, you need to dig a hole in another place. A pallet for building a septic tank can be bought at the store. The finished pallet must be selected based on the size of the future building. It is necessary to install bars around the entire perimeter, otherwise it will hang out.

The foundation can be laid out of bricks. At the bottom of the building you need to lay a layer of gravel 15 centimeters thick. After that, a drain pipe is installed. After the concrete hardens, you can continue the construction of the shower.

Most summer residents have a desire to swim in the soul after excavation. The procedure has a positive effect on human health. Of course, you can buy a shower ready-made. But this will increase construction costs.

It is cheaper to make a shower on your own, without the help of specialists. The water must flow at a certain slope. Don't forget to waterproof your shower. With the help of a waterproofing film, you can prevent the appearance of an unpleasant odor. To do this, you need to lay a special grid. The recommended depth of the drain pit is 2 m.

To save heat, it is necessary to install a polycarbonate roof on top of the tank. It will create a greenhouse effect. A mandatory element of the tank is a sensor that informs the user about the water level. In the absence of water, they can burn out. Therefore, this parameter must be constantly monitored. To equip the floor in the shower, it is necessary to install a drain pipe.

What if there is no running water in the house? To fill the tank you have to carry water in buckets. This is way too labor intensive. Before building a shower, think about the water supply. If you have running water, you can fill the tank quickly enough. Just open the faucet and wait until the container is filled to a certain level.

Advanced home owners have come up with a scheme that automates this process. This can be done using the float system. It is imperative to provide for the installation of a system that is designed to drain excess water. According to the law of physics, the warmest water is on top. Therefore, water intake is carried out from above. At the bottom of the tank, you can install a hose for draining water into the sewer.

Of course, you can use the energy of the sun. In this case, you do not have to spend money on electricity. However, this method has a significant drawback. With the help of the sun it is difficult to warm up a large amount of liquid. In addition, this method can not be implemented in all climatic zones.

In this case, you can use heating using devices that use electricity. The heaters can heat the water to the desired temperature. A person who decides to take a shower sets the temperature himself.

In order for the warmest water to enter the watering can, it is necessary to attach a piece of foam to the hose. Therefore, water is taken from above. To speed up the heating of water, you can make a coil.

A shower can be built at the farthest end of the site, near the fence. On sandy soil, water will not linger in the sump. Due to the rapid absorption of water, rotting of wooden materials that are used as sheathing materials can be avoided.

When building a shower near the fence, the owner gets an advantage. In this case, it is enough to install 3 pillars. So that the pillars do not stagger, it is necessary to dig holes 78 cm deep, fill everything with rubble, tamp and pour concrete.

After leveling the floor, wood processing begins. You can buy aspen boards and impregnate them with a protective layer. Then the lumber is processed with a grinder.

When installing shelves, consider the weight of the barrel. It must withstand a load of at least 100 kg. Corners will rust during operation. To increase the service life of the metal frame, paint with a special paint that can be applied directly to rust.

To install polycarbonate, you can use self-tapping screws. Violation of technology can lead to cracking of polycarbonate sheets in sunny weather.

Therefore, people prefer a summer shower equipped with a heating system. To obtain a convenient and practical design, great attention must be paid to the construction site. A draft after a shower can lead to a cold. With the help of heating elements, you can heat water to a certain temperature even in cold weather.

1. There must be a distance of at least 5 meters between the shower structure and the drain pit.
2. You can proceed to earthworks only after calculating the volume of the drain pit. One person accounts for 0.5 cubic meters.
3. When laying pipes, observe a slope of 3 to 5 degrees.

The simplest design of the drain pit is considered to be the shape of a cube. But this option has a significant drawback. The walls of such a pit lose their strength.

It is best to use a cylindrical drain pit. In this case, the load is distributed evenly and the probability of failure is reduced. In order to increase the life of the shower structure, it is necessary to use bio-based products. Many bacteria are able to process waste. Water will quickly soak into the ground.

The advantage of a plastic tank is that the water does not bloom in them, the joints do not rust, and the properties of the water do not change.

Electric heaters can be installed with your own hands. However, it is best to purchase a ready-made tank equipped with a built-in heater. In this case, the system controls all parameters automatically. The unit has a control panel and switches itself off in case of emergencies.

Humidity in the shower. Therefore, during construction, the following points must be taken into account:

1. Instead of an iron pallet, it is desirable to use plastic ladders. They provide good air circulation and prevent water stagnation.

The tightness of city apartments, especially in winter, is very tiring. And many of us are looking forward to the onset of summer to spend our free time alone with nature, enjoy the singing of birds and bask in the warm sunshine. And gone are the days when country rest was associated precisely with work in the beds. To date, the owners of summer cottages are striving to improve the suburban area and the house no worse than a full-fledged city apartment. And to make life much easier, you don't need much. Sometimes for a wonderful rest and good mood on a hot day, you just need to cool off a bit and admire nature. And even if it is not possible to carry out a full-fledged water supply or equip a pool in a suburban area, you can always find the opportunity to build an outdoor shower.

Peculiarities

A summer outdoor shower on the site will help you quickly and easily refresh yourself after work or a long hot day. And it is not necessary for him to conduct communications, the shower can function without running water. An outdoor shower in the modern view is not just three walls with a hose, it is a full-fledged engineering building, the design of which must be approached thoughtfully and thoroughly.

The design of the summer shower may be different.

• Rack- a simple option that even a beginner can do on their own. Also, similar designs can be inexpensively purchased ready-made in the store, you only have to assemble and install a shower rack on the site.

• Panel- installed along the house, wall or fence. Similar designs can also be purchased at the store or do it yourself.

• cabin- the most common and familiar version of a summer shower for us. The cabin can have three or four walls, and can also be supplemented by a dressing room. A similar design can be installed anywhere on the site.

Depending on the design and location of the summer shower, the method of water supply depends:

• showers with a barrel for heating water - this method is in great demand among summer residents;
• plumbing - such a shower requires a large range of work, since communications are required.

The choice of the appropriate option depends on individual preferences and the functions that an outdoor shower should have. If you have a place to wash yourself, for example, in a bathhouse or a bath in the house, and a shower is needed only to refresh yourself with cool water sometimes, on a particularly hot day, then you should install a small shower head. But if you plan to use the summer structure as a full-fledged shower, then we advise you to pay attention to the cabins with changing rooms, in which it would be useful to provide hot water supply and lighting.

Kinds

An outdoor shower is perhaps one of the most important types of construction in the country.

All types of country street shower can be divided into several types.

• Mobile summer shower. If there is no desire or opportunity to install a reliable and durable structure on the site, then you can resort to a portable summer shower. For water, a bucket or basin can be used, to which a foot pump with a hose is connected. The principle of operation of the design is very simple. One hose from the rubber mat is lowered into a container of water, and the second is used directly for watering. And in order for the water to pour, you need to stomp on the rug. The foot shower device itself is small in size and weight. You can take this rug with you on a hike or expedition. And another advantage of this option is that you can regulate the temperature of the water yourself without any problems. If you want to take a hot shower, fill the container with hot water, and if you want to cool down, take cool water.

• Stationary. It requires a water drainage system. Otherwise, soapy water can get into the beds with a crop, which will adversely affect the plants. Well, if the site has a drain pit for used water or a sewer, then a channel must be connected to them to collect water from the outdoor cabin. Also, for a shower room, you can make a separate drain hole measuring 60x60x60 cm - this volume is enough for an average water flow. The bottom of the pit must be covered with expanded clay or broken bricks. If the soil in the area is sandy, then the walls of the pit must be reinforced with a metal mesh, otherwise the sand may crumble. The easiest way to strengthen the drain hole is to use old tires.

• Warm. If you plan to use an outdoor shower not only in the summer heat, but also in spring and autumn, then the walls must be insulated. Styrofoam or polystyrene foam is excellent for this. But between the wall or thermal insulation, it is necessary to lay a moisture-resistant film, otherwise the insulation will absorb moisture. And in order to always have hot water in such a warm outdoor shower, it is worth connecting the cabin to the domestic water supply.

• Universal. In order to rationally use the area of ​​​​the site, it is possible to place a dry closet under the same roof with a summer shower. You can also combine an outbuilding with a shower. This 2 in 1 solution significantly reduces the cost of construction.

You can choose any type and model of shower for your site. And you can also build an outdoor cabin yourself or buy a ready-made one in the store.

Projects and schemes

There is nothing difficult in making a summer shower with your own hands. And this work should be approached with all responsibility.

To get started, you need to carry out several sequential steps:

• choose the right project;
• draw up a drawing on paper indicating the dimensions of the building and the size of the site;
• choose a place for the future outdoor shower;

• make a marking of the territory;
• buy the necessary materials and tools;
• build a foundation;

• to carry out sewerage for water drainage;
• prepare the drain;
• install the construction of a summer shower;

• install a water tank or connect a water pipe;
• carry out interior decoration;
• install hooks for clothes, shelves and a curtain if necessary.

So in any case, all work must begin with a plan and drawing. This stage will greatly facilitate subsequent work and save you from many problems.

Cabin height should be up to two meters, and the space inside should be enough to turn around, bend over and raise your arms up without constraint. As a rule, about two meters in length and one and a half meters in width are enough for this.

A summer shower project can be simple, but at the same time interesting. And for this you do not need to have special building skills. For example, on the site you can build a country two-room change house with a toilet and a shower under one roof. Such a construction will be especially important during rain or in the cold season. The optimal length of the trailer is 6 meters. This area will be enough to place inside a toilet, shower and changing room.

Each owner chooses a place for a summer cabin independently.

• It is more reasonable to place the cabin on the sunny side. Try to avoid shade, and in order for the water in the tank to heat up faster, it is advisable to find a place where the sun's rays fall throughout the day. If there is no such area in your yard, then you need to consider at what time it will be more comfortable for you to take an outdoor shower. If during the day, then choose an area that is illuminated by the sun in the morning. And if you prefer to use the shower in the evening, it is recommended to choose a place that is illuminated by the sun in the afternoon.
• It is better to choose a flat area with a slight elevation, so the water will drain faster into the drain hole. If you place the shower in a low place, this will undoubtedly lead to stagnation of water, which will later lead to the appearance of an unpleasant odor.

• The place should be protected from drafts - even though the summer breeze is warm, blowing can cause trouble.
• The shower cabin should not be located in the central part of the site - it is better to hide even the most unusual and interesting design from prying eyes.

A suitable place to install a cabin in a suburban area will be several options.

• Area next to a private house. In this case, you can use one of the walls. This is a great option that allows you not to conduct additional communications. Such a shower can be connected to a domestic water supply, and a ready-made sewer can be used to drain the water. In addition, you can additionally carry out lighting so that you can take a shower in the dark.
• Not far from the bathhouse. It is very useful to take a cool shower after the steam room.

• Location next to the pool. In this case, it is not bad to make the lining of the walls of the shower cabin with the same tiles, so as not to disturb the harmony and unity of style.
• Under the same roof with an outbuilding or a toilet. This option allows you to save not only space on the site, but also money.
• Another good two-in-one option is to allocate additional space for a dressing room. Agree, it is not very convenient to wipe yourself with a towel in a narrow, damp shower. And you should think over the project so that water does not penetrate into the locker room.

materials

With the help of modern building materials, you can create an original and elegant outdoor shower both inside and out. Also, for construction, you can use any improvised materials. Undoubtedly, the choice of materials depends directly on the type of construction. And, as a rule, everything comes from the tools that you have and from your building experience.

When building a summer shower, it is not necessary to use expensive materials.

The most popular for the shower are:

• wood;
• brick;
• polycarbonate.

If you know how to use a welding machine, you can build a shower cabin from a metal profile, and walls from tarpaulin or polycarbonate. The frame from the professional pipe will last for several years and will withstand even strong gusts of wind. Also, profile pipes can be connected using steel corners. In this case, you do not need to use a welding machine.

Polycarbonate structures are in great demand among summer residents. And there are several explanations for this. Firstly, polycarbonate showers have a beautiful appearance and look good both in an open suburban area and in a garden. Secondly, despite the dense walls, polycarbonate transmits a lot of light and keeps heat inside, so such structures do not need additional lighting. And thirdly, it is not difficult to assemble and install a polycarbonate shower. The frame for a shower room made of polycarbonate can be either a wooden beam or a metal profile.

As for the shower drain, in this case, only one requirement is put forward for the materials - they must be resistant to high humidity.

Best to use:

• ruberoid;
• hydrostekloizol;
• concrete with the addition of PVA;
• PVC film.

Design

The main rule that must be observed when arranging a summer shower is that the design of the cabin should not stand out from the general style of the site. A well-thought-out design will add a touch of creativity to the site. And having a lively imagination, you can afford to equip not just a summer shower, but a real construction masterpiece.

It is generally accepted that the color of the summer shower should match the shade of the walls of the house, garage, gazebo and other structures on the site. But you can also choose shades that harmonize with each other. The walls of the cabin can be decorated with decorative elements and turn an ordinary summer shower into a bright and original accent. But bright and catchy tones are used extremely rarely, because after all, you should not turn the shower cabin into a central element.

The shower cabin can be decorated in various styles. So, for example, for high-tech style, you can use white sheets of stainless steel. And for minimalism - a shower with a white curtain.

Moisture-loving plants can be planted near the booth, which will not only add mood to the site, but will also facilitate rapid drainage.

Base

As a rule, for a small summer shower without a dressing room, about 1x1.5 meters of base is enough. First you need to make markings with wooden pegs. The base of the summer shower must withstand a weight of about 200 kilograms. Therefore, in order to ensure maximum structural strength, the posts must be dug into the ground or the base concreted. Pour concrete over the selected area, and place bricks on the sides. They will perform the function of the sides. The foundation itself should slightly raise the entire structure above the ground.

Even at the design stage, you should take care of the water collection tank. It can be located directly under the base of the cabin or nearby, then the water will additionally pass through inclined pipes. But keep in mind one point: a large amount of water should not stagnate in the pit, otherwise unpleasant odors throughout the site cannot be avoided. It is more reasonable to install a channel for collecting water and connect it to the sewer pipe.

You can put a wooden pallet with slots down on the floor, so the water will quickly leave. In addition, in this case, the water will not splash. Also, instead of the floor on the ground in the shower, you can pour large pebbles or artificial porcelain stoneware. Another advantage of such a coating is that even with high humidity the surface will not slip.

frame

You can build a frame for a summer shower from various materials.

If the frame posts are made of wood, then you need to process the wood from decay and strengthen the entire structure with additional corner braces. And also it is worth choosing exclusively dry coniferous wood. The dimensions of the bars are selected based on the weight of the water barrel and the thickness of the polycarbonate. The frame must withstand an impressive weight - about 200 kilograms.

The metal frame is assembled in stages using a welding machine or steel corners. For vertical racks, a pipe with a diameter of 40 mm with a wall of about 2 mm is suitable. Intermediate horizontal connections will strengthen the entire structure and make the summer shower more reliable and durable. All metal elements must also be additionally treated with special solutions to protect against corrosion and rust.

The plastic frame has an attractive price, but is not able to withstand a lot of weight. The overall design will last about 5 years.

An aluminum frame will cost more because aluminum has better performance and is more expensive. Many manufacturers of shower cabins prefer the aluminum frame.

A frame made of brick, stone or concrete is a great option for creating an unusual and reliable shower.

After creating the frame, you can proceed to the sheathing of the structure.

Roof

You can also make a roof from various materials. The choice depends on a number of factors: on the type of construction of the building, the features of the roof, climate, finances, as well as on the preferences of the owners of the cottage.

Polycarbonate is a great option for a roof in warm climates. For a shower of standard sizes, only two sheets are required. You can use a transparent material, then the water in the barrel will heat up faster, and it will be light inside the cabin.

Slate should be used if the shower is built of brick or stone. Although for some such a building will resemble a small house or a barn, it will be possible to take a shower in the cold season.

Tiles are the most durable and reliable material.

Roll materials are an easy and quick way for a stationary outdoor shower. On such a surface, water will quickly drain to the ground. The advantages of roll materials include fire safety and ease of repair.

Sheet steel allows you to quickly and easily complete the construction of the roof. But at the same time, the sound of water drops during the rain will be clearly audible.

The corrugated board has a specially coated polymer composition, which increases the service life up to 30 years.

The roof structure should have a slight slope to allow water and snow to run off. If the water tank is installed on the roof, then the materials should be treated with water-repellent impregnations. And for reliability, additionally cover several layers of ordinary oilcloth on top.

Finishing work

The exterior finish of the shower cabin must be made of durable and moisture-resistant materials. And besides, the outdoor shower should be combined with the rest of the buildings on the site.

• Film shower- the easiest and most affordable option. But such a cabin will need to be brought into the room with a sharp change in weather. And in fact, a film shower will last only one season. But you can build such a cabin in one day. To do this, you will need a double-sided corner frame, assembled like a screen, as well as a thick film or waterproof curtain.
• Shower room made of polycarbonate. Such cabins can be purchased ready-made in the store, you do not need to choose a project, draw up a drawing and adjust the polycarbonate to the desired dimensions. But if you decide to do all the work yourself, then choose colored polycarbonate with a thickness of 6-8 mm. Behind it, it will absolutely not be visible what is happening in the soul, but natural light will calmly penetrate inside and provide the necessary lighting. For corners, you must also purchase a docking corner. With it, it will be easier to assemble the cabin.

• The brick shower needs to be plastered. All work must start from the top down. First, a small layer is applied, and then the amount of mortar is increased, but one layer should not exceed 5 mm. In this way, all sides of the cabin are gradually plastered. When working on corners, experts recommend additional use of wooden slats. With their help, it will be possible to complete the work much faster.
• Wooden shower must first be treated with protective agents so that the wood does not rot. Then the boards can be covered with drying oil and, after complete drying, complete the finishing work by painting all the walls. Inside, a wooden cabin should not be painted; it is better to choose plastic panels for interior decoration. They are easy to install and reliably protect the tree from moisture.

• Cabin made of corrugated board- a simple and reliable option. It is better to order sheets of corrugated board of the required dimensions in advance in the store, then you will not have to adjust the material yourself and will only have to assemble an outdoor shower like a designer. Also, corrugated board can not be painted and not treated with additional preparations. Fasteners should be immediately selected according to the color of the cab. Sheets are fixed to the frame with a screwdriver. Also prepare a simple pencil, tape measure and level in advance. The corners of the shower cabin can be smoothed by bending the sheet of corrugated board along. For the second method, you will need to additionally purchase ready-made galvanized sheet corners.

How to choose and install a tank?

The choice of tank depends primarily on the throughput of the shower. To refresh an adult, 20 liters of water is enough, and to wash, it will take about 50-100 liters. And also count how many people you usually have on the site. Based on these data, it is already possible to decide on the choice of the volume of the barrel.

As a rule, a volume of 200 liters is sufficient. And the maximum allowable volume is 500 liters. The barrel must be completely closed, otherwise the water will become clogged with leaves and small branches. If the structure is open, then a cover can be provided in advance. And before installing the tank on the cabin roof, it is necessary to strengthen a solid platform.

The easiest way to connect the tank is to make a hole in the barrel for the tap and attach the hose. In a plastic tank, this can be done with a drill, and for metal, you need a metal drill.

The material of the tank also plays a big role. It is well known that metal heats up much faster than plastic, but, nevertheless, experts advise installing a plastic barrel in a summer shower. Unlike metal, it has an optimal service life and is not subject to the harmful effects of corrosion. An excellent option for an outdoor tank would be plastic or stainless steel. And it is wiser to choose a flat tank, which at the same time can be used instead of a roof. Another plus of such a tank is that the water in it will heat up evenly.

Interior arrangement

After completing all the installation work, you can proceed to the finish. The main requirement for materials that will be used inside the cabin is that they must have excellent moisture-resistant characteristics.

The wall inside can be plastered, painted with paint or trimmed with plastic panels. Also a good option for walls is wooden lining.

When laying the floor screed in the shower room, a slight slope is maintained for quick drainage of water. The interior space inside the shower cabin can be tiled. At the same time, it will perform not only protective functions, but will also be used as a decor.

But today, designers recommend abandoning tile panels - this method of finishing has long been outdated. Use tiles with unusual patterns, patterns, or ornaments. You can also use a mosaic - it always looks appropriate.

After the work with the finishing of the walls and floor is completed, you can proceed to the installation of the door. Also in the shower cabin, you can additionally install a tap at the level of one meter. In this case, it will be possible to wash the feet or shoes after working on the site. And it will also be very convenient to wash the paws of pets.

At the dacha in the summer there should always be an opportunity to wash. For the first time, you can use a portable mobile shower. How make a summer shower in the country with your own hands we will tell in this article, it will also offer soul blueprints different options and sizes with photo and step by step instructions.

mobile shower

The first option is made as a mobile shower with a foot pump, in which you don’t even need to build a booth and install a large water tank. As a source from which water will flow, you can use a bucket or tank. One end of the hose is lowered into the container, and the other is connected to a foot pump, which most often resembles a rug.

A hose and a watering can are connected to the output of such a pump. In order for water to pour through the watering can, you should stomp on the rug, pressing alternately with your feet on the pads of the pump.

The advantages of this type of mobile shower are that you can take it with you anywhere. In warm weather, you can swim outside, if it's cold - indoors. Another plus is that it is easy to transport. It is light and compact, so it can fit in a regular bag. In addition, you can choose the temperature of the water yourself. To refresh yourself in the summer heat, you can pour cooler water, and to wash yourself well, pour warm water into a container. This is quite a decent option for a summer shower.

Summer stationary shower in the country

The first question in designing a shower is where the water will drain. If there is nearby outdoor toilet with a drain pit, where it will be possible to lay a pipeline from the shower. But if bacteria or special preparations are used to process waste in the drain pit, then this option will not work. A certain environment is needed to process waste in this way, and draining from the shower into the pit will disrupt the chemical composition and humidity levels.

It is better if a separate drain hole is prepared for the shower. If the soil absorbs normally, then it is quite enough to dig a hole 60 * 60 * 60 cm in size next to it. This is enough for an average water consumption. Under the conditions that there are many residents or they are lovers of water procedures, then you can dig a larger hole. The bottom must be covered with expanded clay or broken bricks.

If the soil is sandy, then there is a danger of shedding sand. In this case, the walls must be strengthened with a net, driving in pegs on the sides. Sometimes the walls are sheathed with the remains of boards.

Base

Summer shower most often does not weigh much. Therefore, do not bother with a good reason.

You can set the level of small foundation blocks 20 cm in height. This distance is enough so that the wood does not rot if it is used to make a frame.

If the frame is welded from metal, then it is installed directly on the slab or paving slab.

You can cast the base yourself. To do this, formwork is made, reinforcement is laid and poured with concrete.

Frame manufacturing

The size the soul can be anything. In addition, often one part of the building is made a shower room, and the second is a locker room, pantry or room for a water heater.

If you plan to make an ordinary shower, in which they will only wash, then you can use a square with sides of 90 cm. In this design, there will be a curtain instead of a door. The height of the rack is made 2.2 m, higher only if necessary.

But it should be understood that this size will be convenient for people of average build. A width of 100 cm is considered more comfortable, and best of all - 120 cm. A frame is assembled from metal or wooden bars.

metal

In order to weld a metal frame:

• Use a corner with a thickness of 4-5 mm.
• Shelves in width are selected depending on what the load will be.
• If the sheathing is light (film, waterproof fabric), and the plastic water tank is up to 100 liters, then you can take metal with a minimum cross section.
• If the load is large - the sheathing is heavy (lining), and the water tank is voluminous (more than 200 liters), then the cross section should be larger (corner by 70).

Advice! For a metal frame, a good option would be to use a profiled pipe.

• For racks, a wall thickness of 3 mm is suitable, and for strapping - 2 mm.
• Such a pipe may have a rectangular or square section. Thanks to this, the process of fastening the crate and sheathing becomes easier.
• In order to attach something to the corner, you must first fasten the bars, and then attach the harness to the bar. It is convenient to fasten the harness to the profiled pipe immediately with the help of bolts or screws, having previously drilled holes in it.

It will be most convenient to weld the frame. If this is not possible, then you can make a metal frame with bolts. To do this, you need to cut the pipes of the desired length, take thick mounting angles and assemble the frame with bolts.

from wood

A wooden frame can be assembled from a bar:

• For the lower trim, it is recommended to take a pine beam, 100 * 100 mm or 150 * 100 mm.
• For racks, you can choose smaller sections.
• Select the section of the racks for the load. If the heavy tank is at the top, 100mm can be used, if the racks will only support the roof, then 50mm can be used.

Mounting methods can be different:

1. The correct option is to cut a spike and a groove.
2. You can make it easier and dock one to the other, reinforcing the connection with corners.

After the racks are set, you should make the top harness:

• For her, a section of 50 * 50 mm or 50 * 40 mm is taken. You can make intermediate crossbars 2 or 3, depending on what will be used for sheathing. They need to be made more if timber or lining is used. The wood is not always flat, so you will need to align the geometry with force.

Skin selection

In order to fit the frame, you can use various materials:

• Film or oilcloth. It will not last long, most often it will last for a season. But this option is quite cheap, this is its advantage.
• Impregnated fabric. Also a simple and inexpensive option. You can take the fabric that is used for awnings or tents.
• Lumber. It can be anything: lining, timber imitation or block house.

Advice! You should not buy raw material if you plan to install it right away. Such materials can dry out in a year, and to such an extent that the boards will pop out of the grooves. If the sheathing is planned to be done as a braided fence, you can take the simplest boards.

• Slate. It is better to take a polymer. Asbestos is also often used, although they know that this material is harmful.
• Professional sheet. If it remains from use for other purposes, then they can also sheathe the frame of the shower.
• Polycarbonate. He has a drawback - from almost transparent. It is necessary to seal the sections, because moisture and dust can get into them, algae can settle. Then the shade of polycarbonate will eventually change to gray-green, which does not look very nice.

Sheathing can be made from any material at hand, the main thing is that it fulfills its main purpose.

Watch the video! Do-it-yourself summer shower made of polycarbonate

Tank

Any suitable container can be used for the tank. Often, a metal or plastic barrel is used for this. You can buy a container. They are widely presented in different sizes and from various materials:

• plastic;
• black metal;
• stainless steel.

Plastic tanks have their drawbacks. The water in them heats up more slowly and worse. Residents of the southern region should not worry about this, since there is enough heat there, but residents of the Middle Strip should take the choice of a tank seriously. Although in this region, even in black metal barrels, water has to be heated, since the sun cannot cope with this.

But there are also advantages to plastic tanks. They are light, inexpensive, if they have a rectangular shape, they will be conveniently located on the shower frame, there is no need to think about how it is more convenient to fix them.

Using a metal container will allow the water to heat up faster, especially if it is painted black. But ordinary metal rusts, and by the end of the season there will be a lot of rust. She will clog the watering can and remain on the body. This is the main disadvantage of using metal barrels.

It is better to buy a stainless steel tank. It will also heat water quickly, but it will be more expensive than the above options.

Pallet

There are two options shower designs:

1. the drain pit is under it;
2. the drain is taken away from the building.

In the first case, you can simply design a pouring floor: lay boards with a gap of 3-5 mm. Especially this option is suitable for sandy and sandy soil. Water will quickly leave without stagnation, without causing any problems or inconvenience.

If the design provides for drains to be diverted to the side, then a pallet should be made in the shower. You can buy a ready-made pallet. Then you will need to take into account its size when building the frame. The bars on which it will be attached must also be selected with the appropriate section. It is not difficult to connect it, a siphon with a flexible hose is installed, as in a regular bathroom.

If the pallet is made of plastic, then in addition to the bars, additional support is needed so that it does not “walk”. You can lay it out of bricks on cement mortar.

Important! When laying out the support, you will need to leave room for the drain hose.

You can make a pallet yourself, which will have a larger drain than a plastic one. To do this, pour a concrete slab:

• It is necessary to dig a pit in size, with a depth of 30-40 cm.
• Gravel is poured at the bottom, a layer of 20 cm.

• After that, you need to install a drain pipe and a drain grate.
• Formwork is placed on top, you can make it non-removable, made of brick.
• Crushed stone must be compacted, poured with concrete (M 250).
• In order for the base to become strong, it is necessary to leave it for 7 days if the ambient temperature is above +17 degrees.
• After a week, you can continue building and install the frame.

Filling the tank with water and heating

Usually there are no problems with filling the tank with water:

1. The easiest way is to top up with buckets. This is not very convenient, but when there is no choice, the option is not bad.
2. It is possible to mount a supply pipe with a valve from the water supply. When it is necessary to add water, the tap opens and the tank is filled.

How to autocomplete

Automatic filling of the tank is the most advanced option. A float system regulates the opening / closing of the water supply, such as the one in the toilet bowl. But in such a design, provision should be made for draining excess in case of a breakdown. And it would be nice to turn off the tap if the cottage is left for a long time, so as not to turn the site into a swamp.

The water intake for the shower takes place close to the surface, as this is where the warmest water is. But the main thing is to install the pipe on the other side of the cold water inlet, otherwise the water will be cold.

Two pipes lead to the sewer. One is overflow. Thanks to her, the tank will not overflow if the float mechanism breaks. The second pipe is for draining. A tap is also installed on it so that the system can be closed for the winter.

Heating

The “cheap and cheerful” option is solar heating. Water is heated through the walls of the tank. But the water column is large, so heating does not always occur as quickly as we would like. There are various tricks that are used to heat water with sunlight.

In the tank, the warmest water is at the top. And the supply in the traditional form occurs from below, that is, cold water is taken. There is one trick on how to make sure that the warmest water enters the watering can. To do this, you need to attach a hose to it, and attach it to a piece of foam that floats in the tank. Thus, water is taken from above.

There is an option to speed up the heating. For this purpose, a "serpentine" is made. Two pipes are welded in the tank, one is in the bottom, and the second is higher. A black rubber hose is connected to them, which must be laid out in rings in the sun. It turns out a fairly active movement of water, provided there is no air in the hose.

If sunlight alone is not enough to heat water, you can bring electricity to the shower. You can use wet heating elements with thermostats to set the required temperature. They are used in storage water heaters, so buying them is not difficult.

It is worth taking safety measures when supplying power to the shower. To do this, you should install an automatic device with an RCD.

Watch the video! Warm water in the barrel constantly

Step-by-step instruction

Instructions for creating a structure summer soul in the country, presented below.

The size designs will be 1x2m.

Materials needed: boards 50 mm and 25 mm, 3 m high,

Making a column foundation

• Pits are made at the corners of the building, of arbitrary depth, for example 1m (the deeper, the better). So that the foundation does not warp after frost, theoretically it is necessary to dig a hole deeper than the soil freezes through.

In Central Russia, this depth is 1-1.3 m. But you can make a hole 80 cm deep, pour 20 cm of rubble on the bottom, and then 20 cm of sand, then the water will not stagnate and the columns will not warp.

• On top of the cement mortar, we lay out columns of solid brick measuring 25 * 25 cm 10-20 cm above ground level. An anchor steel strip 3-4 mm thick is embedded in each column. It will be attached to the lower trim and vertical posts made of boards 50 * 150 mm.

building frame

The lower trim, as well as vertical posts made of boards 50 x150 cm, diagonal braces (made of boards 25 * 150 mm) for structural rigidity - we fasten all this to the anchor strip with M8-M10 bolts. This must be done, because at a given height, even a small wind can knock down an unsecured structure, because it has a small base area and a decent height.

Roof

A gable krusha is made from a board of 25 mm. It will be enough to raise the center of the roof 50 cm above the edges so that rainwater flows. The same slope can be made for a pitched roof.

Watch the video! Do-it-yourself country shower

In the summer, even when resting, and not working, the opportunity to wash is necessary in the country. The easiest way to organize this is on the street, and not in the house. You can make a portable - mobile shower. This is a great first time option. But I want something more solid. To do this, build a summer shower in the country. Although it is stationary, it is lightweight.

Portable summer

Let's start with the simplest models, which do not even require cubicles or large capacity devices. There are mobile showers that work on the principle of a foot pump. The source of water is any container that you put next to you - a bucket, a basin, a tank - whatever you have. You lower the end of the hose connected to the foot pump into it, which most often looks like a rug.

Foot summer shower - toptun

A hose with a watering can is connected to the outlet of this "pump". To get a stream of water, trample on the mat alternately pressing the pump pads. We trampled - the water went.

What is good about this option is that you can carry it with you. It's warm outside - wash on the lawn. It got colder - they went into the house, put a trough, washed themselves there. You can also take this shower on a hike - it fits in a standard package. Another plus is that you can regulate the temperature of the water yourself: if you pour it warmer, you wash yourself in warm water. If you want to freshen up, take a bucket of cooler water. A good option for a shower for summer use.

Summer stationary shower in the country

When installing a stationary shower, the first question arises: where to drain the water. If there is already a drain pit for, you can lay a pipeline there. But this solution is not the best if you are using bacteria or waste treatment products in the pit. In this case, a certain humidity is required, and with a shower it will be clearly more than normal.

For the shower, it is better to make a separate drain hole. If the soil has normal drainage capacity, it is enough to dig a hole about 60 * 60 * 60 cm nearby, fill it with expanded clay, or you can use broken bricks. This should be enough for the average water consumption. If your family belongs to the category of "waterfowl" or the water goes badly, make the hole bigger.

On sandy soils, you may encounter another nuisance: sand can crumble. Then the walls can be strengthened with a net by driving pegs on the sides. Another option is to sheathe the walls with boards (as in the photo). But this is if the board is in the remnants.

Base

Whatever the summer shower, it usually weighs a little. Therefore, the basis for it is not made too serious: there is no point in burying money. Most often, small foundation blocks are used, which are set according to the level. The shower in the country is raised above ground level by 20 cm or so. This is enough so that the treated wood (if it is used as a frame) does not rot.

If you are going to cook the frame from metal, you can put it in general on a paving slab or slab set to the level. If desired, you can cast the columns yourself: put the formwork, lay the reinforcement and pour concrete.

frame

The dimensions of the soul are chosen arbitrarily: there are no standards here. In addition, the shower cabin is often only one of the parts. In another, they arrange, for example, a locker room or a room for a water heater (electric or wood-burning - according to the conditions). Someone plans to take the other half under the pantry or store inventory. So a country shower is not always just a booth "for washing."

If, however, a light structure is planned, in which they will only be washed, and, moreover, the simplest option is with a curtain instead of a door, you can take the minimum dimensions: a square with a side length of about 90 cm (drawing below), the height of the racks excluding the tank is 2.2 m or higher (if the family is tall).

But such a width is far from convenient: it is too crowded even for people of average build. It is more comfortable with a minimum width of 100 cm, and preferably 120 cm. This frame is assembled from metal or wooden blocks.

metal

The metal frame for the shower is boiled from a corner with a thickness of at least 4-5 mm. The width of the shelf is chosen depending on the planned load. The frame is usually loaded with water tanks and sheathing. If you plan to put a plastic square container of 100 liters on top, and cover the walls with a film, impregnated cloth or something equally light, you can take the section to a minimum. If you plan, for example, two 200 liter barrels, and sheathe the shower cubicle in the country house on both sides with clapboard, the load will be completely different. And here large sections are required.

Another metal frame for a country shower can be made from a profiled pipe. The wall thickness for the racks is 3 mm, 2 mm is also suitable for strapping. It has a rectangular or square section, which greatly facilitates the fastening of the crate and sheathing. To attach something to a corner, it is often necessary to first screw the bars to it, and attach the rest of the strapping to the bar. The piping can be fastened directly to the profiled pipe - with bolts or screws with pre-drilled holes.

The metal frame is best welded. If there is no apparatus, you can make a collapsible frame on bolted joints. Craftsmen do it this way: they cut pipes of the required length, take thick mounting angles and assemble the frame with bolts.

In case you plan to learn how to weld metal, the choice of welding machine is.

from wood

A wooden frame for an outdoor shower is assembled from a bar. For the lower trim, as a rule, a pine beam 100 * 100 mm or 150 * 100 mm is used. Racks can be set to a smaller section. Again, it depends on the load. If the tank on the roof is voluminous, make racks from weaving. If they hold only the roof (water is heated in titanium nearby) or a very small tank, then 50 * 50 is enough.

You can attach the bars in different ways. If correct, you need to cut a spike and a groove. If in a quick way, you can dock directly, reinforcing the connections with corners.

Having set the racks, they immediately make the upper harness. It already definitely goes 50 * 50 mm or 50 * 40 mm. They also make intermediate strapping. There may be one, two, or even three. If you are going to sheathe the shower with clapboard, imitation of a beam, it is better to fasten the crossbars more often: it will be possible to more tightly fit not quite even lumber. The quality of wood materials sold on the market is, to put it mildly, low. We have to correct the jambs of geometry due to force.

The construction of a frame from a bar is shown in the video

sheathing

You can fit the frame with any material:

You can use any other fence that comes to your mind and will perform its functions. For example, in one summer cottage, the shower sheathing was woven. Type .

shower tank

As a tank for a summer shower, use any suitable container that is on the farm. Most often - this is a barrel - metal or plastic. If there is nothing suitable, you can buy a container. They are available in a large assortment: plastic, metal - from ferrous metal and stainless steel.

Not everyone likes plastic ones, since water heats up worse in them. For the southern regions, this is not scary - there is already enough heat, but for the Middle Strip, it can be critical. Although in this region, most of the summer, water even in black metal barrels requires heating. On the other hand, plastic containers are inexpensive, light, there are square flat shapes, which means they fit well on the shower frame and there is no need to invent a method of attachment.

In a metal barrel, water will heat up faster, especially if it is painted black. But if it is made of ordinary metal, there will be a lot of rust by the end of the season. So much that it will be noticeable on the body. This is the main disadvantage of such tanks. Much better than stainless steel. If finances allow, allow yourself one.

Summer shower tray

There are two options for a country shower device: when the septic tank (drain hole) is located directly under the shower stall. Then you can simply make a pouring floor: lay boards with a gap of 3-5 mm. A simple option that works great on sandy and sandy soils. In this case, the water leaves very quickly, without stagnation anywhere, therefore such a device does not cause any inconvenience.

But this option is only suitable if you plan to use the shower only in warm weather. And spring-autumn will not go - it will be cold, as it will blow from below.

If a normal drain is required or you need to divert the drains to the side (drain pit away from the building), you need to make a pallet in the shower. The easiest case is to buy ready-made. Then, during the construction and selection of frame sizes, you will have to focus on the size of the pallet: under it you need bars to which it is attached. They also connect it as standard: they put a siphon with a flexible hose, as in a bathroom.

If the pallet is plastic, just bars around the perimeter will not be enough: support is required under it, otherwise it “walks” too much. This foundation is usually laid out of bricks. You can bind them with a solution. Just remember to leave room for the drain hose.

In some cases, they try to make a more solid drain: without using a finished pallet. In this case, a concrete slab is poured. To do this, they dig a pit of the required size, with a depth of about 30-40 cm. A layer of gravel 15-20 cm thick is laid on the bottom. Already at this stage, a mortgage is installed - a drain pipe and a drain grate. They put up formwork. It can be non-removable - made of brick. Crushed stone is rammed, everything is poured with concrete (). A week (at a temperature of + 17 ° C and above) is waiting for the base to gain strength. After you can continue work: put the frame and continue construction.

Tank filling and water heating

Filling the shower tank with water is usually not a problem. Sometimes they carry water in buckets - if you want to wash, you will carry it. Not very convenient, of course, but it happens ... If there is water supply in the country, they fill it with a hose, install a supply pipe with a valve. It is necessary to add water - open the tap, the tank is full - closed.

How to autofill a tank

The most advanced do automatic filling. Then the water supply is opened / closed by a float system similar to the one in the tank. Only in the event of a breakdown, it is necessary to provide for the drainage of excess water. And, preferably, when leaving the cottage, shut off the supply tap. And then you can turn your own and neighbor's cottage into a swamp.

An exemplary scheme for the implementation of auto-filling the tank is shown in the figure above. Please note: water is drawn into the shower close to the surface: this is usually where the warmest water is located. Only this pipe is placed at the opposite end from the cold water inlet, otherwise the water will still be cold.

Two pipes go to the sewer: one overflow (mustard color). With its help, the tank will not overflow in the event of a breakdown of the float mechanism. The second drain into the sewer for a complete drain (brown). It will come in handy during the conservation of the system - draining for the winter, therefore a crane is installed on it.

Organization of heating

The easiest option is to use solar energy. Yes, it heats water through the walls of the tank. But the water column is too large for it to warm up quickly. Therefore, people come up with various installations for solar water heating.

As mentioned above, in the tank the warmest water is at the top. And the traditional feed comes from the bottom. That is, we take the coldest water. In order for the warmest water to enter the watering can, a hose is attached to it, and it is attached to a piece of foam that I let float. So the water intake is from above.

To speed up the heating of the water, they make a “coil” (in the photo above, this is the right figure). At the bottom of the water tank and above, two pipes are welded in one of its walls. A black rubber hose is connected to them, which is folded in rings in the sun. If there is no air from the hose, the movement of water will be quite active.

If the sun is not enough for you, but you can bring electricity to the soul, you can use heating elements (wet). We need them with a thermostat so that you can set the desired temperature. They are usually used in storage water heaters, so you can find them.

When you pull the power line to the shower, do not forget to install an automatic device with an RCD. This is the minimum that will ensure your safety.

Building a shower in the country: a photo report

It was decided to use a fence at the far end of the site as one of the walls of the shower. It was decided to do a shower with a locker room - it's much more convenient.

The soils are sandy, the water drains very quickly, so only one tire was buried for draining. Shower tests have shown that no more is needed. Much more water was poured than in my barrel, but no puddles were observed.

Then the frame was welded. A rectangular pipe 60 * 30 mm was used. It's a bit too much for this design, but they used what was: the remains of the construction of the fence.

Having welded the floor frame, and having indicated its level, they formed a drain. They reported the missing height with a brick (battle, remnants). Everything was filled with concrete, forming a drain into the tire.

Leveled the floor and in the second half, left to set. Started working on wood. Purchased aspen board. She was first treated with a skin fixed on a grinder. After impregnated with a protective composition.

While the impregnation dries, we continue to cook the metal frame for the shower. The middle piping was welded from the same profile pipes. Then it was used as a scaffold for working at height. Already dried boards were placed on the strapping pipes. From this pedestal, the upper harness was cooked.

The frame is almost ready. It remains to weld the frame under the barrel at the top.

The metal used is old, so it's covered in rust. She was cleaned off by a grinder. Then the frame of the shower was painted three times with rust paint. It was chosen in blue, as it was planned to sheathe the shower with blue polycarbonate.

Polycarbonate was mounted on self-tapping screws. During installation, neither special nor ordinary washers were used. This is a violation of technology, which can lead to the fact that in sunny weather it will crack. This material has a large thermal expansion, which is enhanced, since in this case it is fixed on a metal frame.

The barrel in the barn has been washed. Pipes are welded to it. One is for filling water, the second is for connecting a watering can. After that, the barrel was painted black.

Preparations for the summer season are already in full swing. Someone uses summer cottages for growing crops, someone prefers to sow them with lawn grass, plant ornamental plants and just spend time in nature. Be that as it may, on hot summer days to freshen up and take a cool shower everyone wants. It is not always possible to hire a construction team to build a shower on the site, and such costs will not always be justified. So that you can competently and easily cope with the construction process, in this article we will look at 8 tips for summer shower arrangement at the cottage with their own hands.

1. Where to start?

If you have been thinking about building a summer shower in your country house, then you already have an idea of ​​how it will look like and what you need to purchase. In addition to the design itself, important parameters are:

• Choice of location;
• Shower size;
• Water tank volume;
• The nature of the building - temporary or capital.

Many try to choose the most secluded corner behind the house or in the shade of trees in order to hide such an intimate structure from prying eyes. This is what is the main mistake! By building a shower among trees, you will be exposed to constant attacks of insects that love moisture and coolness so much, and deprive yourself of the opportunity to naturally heat the water in the tank. That's why place for the future building should be located in an open, well-lit area and in no case be in a pit or in a lowland. Even if you plan on using a heated tank, it's wiser to ditch it in order to save money on hot days. The building itself should not be located at a small distance from. Taking a shower late in the evening, you need to get home as soon as possible so as not to get sick.

Concerning size future the buildings and the volume of the water tank. The recommended height of future walls is 200-300 cm. It is necessary to build on the growth of the tallest family member, who should not rest his head on the shower head. Width and length shower space is calculated depending on whether the building will have a dry dressing room or be limited to only a wet area. The option with a dressing room is, of course, more convenient, the clothes will be protected from getting wet, and you will have the opportunity to change clothes comfortably. Thus, your shower will consist of two sections, separated by a partition. An area of ​​​​220 × 120 cm is quite enough for these two zones, even taking into account the skin.

Choosing a tank for water, it is necessary to take into account the number of people who will use the shower, and the intensity of its use. If you come to the dacha only on weekends and use the shower after a hard day's work, then a container that will hold the amount of water at the rate of 40 liters per person is quite enough. This will allow each user to pour water continuously for about 10 minutes. If a much larger number of people take water procedures in a row, you should think about a larger tank. But keep in mind that temporary buildings will not withstand containers with a volume of more than 200 liters. As the tank itself, you can use iron or plastic barrels, or purchase ready-made country models with a built-in watering can. A little advice- if you paint the surface of the tank with black paint, the water in it will heat up much faster due to the ability of black to attract heat.

So let's select basic moments:

• Location - in an open, elevated, bright area, at a maximum distance of 2-4 meters from the main building;
• The size of the room - the height is selected taking into account the growth of the tallest family member, the minimum comfortable perimeter is 100 × 100 cm;
• The size of the water tank capacity is 40 liters per user, multiplied by the number of people who will receive water treatments in sequence.

Character future the buildings- temporary or capital, it is necessary to choose based on the following parameters:

2. We equip the foundation and ensure the outflow of water

The basis of any structure, of course, is reliable. In the case of a summer shower, the foundation must not only protect the structure from groundwater washout and subsequent subsidence, but also be able to quickly drain large quantities of used water. Building any foundation starts with markup. In the selected place, you need to draw a contour. For example, the size of the shower will be 120 × 120 cm - in such a space it will be comfortable for a person with any build. At the corners of the rectangle, you need to drive in pegs, pull the cord around the perimeter and check the dimensions with a tape measure.
Such markup is universal and is performed before the construction of any kind of shower. Now consider types of foundations for various buildings.

Foundation for a simple temporary shower

For the construction of a temporary nature, it is enough to remove the top layer of soil 15-20 cm deep within the outlined rectangle and level the area. Now you need to make a pillow that will help drain water. To do this, prepare a mixture of crushed stone and. You can simply fill the hole halfway with sand, and pour a layer of rubble on top. Small stones will contribute to the settling of soap deposits on their surface. Additional filtration sandy layer will avoid rapid mulching. Such a design can be placed near the garden without harm to plants. On top of such a base, they usually fit, which serve as the floor in the summer shower. To prevent the rapid decay of wooden materials that will often come into contact with water, it is recommended to place pallets or boards knocked together at a height of 15-20 cm above ground level. For formwork you can use old bricks or. They are laid out around the perimeter of the base, leveled and rammed with a mallet.
You can use wood for wall or floor decoration only after, which will make it moisture resistant. The most effective way is impregnation with hot oil and subsequent opening with drying oil or. The arrangement of such a foundation will allow you to use an outdoor shower for more than one season.

Foundation for capital construction

If the shower will be used frequently and not by one or two people, it is necessary to think about the construction of a capital building. The most expensive way will be a brick construction. But it is easiest to heat it in the cool season. To do this, it is enough to insulate the walls. The best option would be a frame building made of metal or wooden beams. Particular attention should be paid to the arrangement of a reliable foundation. In this case, it is necessary to fill foundation from concrete.

According to the markup, you need to dig a hole about 30-35 cm deep. Mortgages must be made along the perimeter of the rectangle. For these purposes, you can use old iron pipes. The larger their diameter, the stronger the structure will be. At the locations of the pipes, a hole up to 30 cm deep is made with a drill, into which pipes or wooden beams are hammered. If you use a tree, then you need to protect its surface by wrapping it with roofing material or treating it with hot bitumen. After that, a cement-sand mixture is poured. Wooden mortgages can be made not only in the corners, but also around the entire perimeter of the base. To do this, use a sufficient width of the logs, which can provide further installation of the floor. The base must be level. This will help prevent the accumulation of water in places with slopes. Filling is carried out according to the technology of arrangement. Use special building beacons and rule.
disadvantage the foundation, which is made by pouring, is that you can start arranging the internal space only after it has completely dried. For brick buildings, you can use a cast reinforced concrete slab with a thickness of 170-300 mm as a base. This will significantly reduce construction time.

Arrangement of water drain

Any capital construction needs a high-quality outflow of water.

• Best for waste collection septic tank, which must be placed next to the shower, but in no case under it. If you decide to save space on your site and still place it under the shower, after a short period of time you will begin to feel a sharp, unpleasant smell inside the building. In addition, there is a risk of soil collapse around the septic tank and, as a result, the destruction of the foundation. The recommended distance from the shower cabin is 1-2 meters. A drain pipe is removed from the shower tray or a drain ditch is drawn into the septic tank, which must have a sump and a drainage tank. A pit is being dug for the receiving chamber. It must be airtight. It can be a tin barrel or. It is recommended to cover the container with a lid so that rain or groundwater does not fill it. Nearby is a leaky drainage tank. It should be installed on a pillow of sand and gravel. These two compartments are interconnected by pipes.
  
• Another option for collecting waste - cesspool. To equip it, you need to dig about 2m3 of earth. This is the optimal volume that will ensure long-term use. At the bottom of the pit, a drainage cushion is made of sand and gravel, and the walls must be strengthened and made waterproof. You can overlay them with bricks, use ready-made concrete rings, or you can strengthen the pit with old ones. Equipping the drain pit, do not forget that it needs to be pumped out. In this regard, it must be located in a place where unhindered access of special equipment will be provided. In addition, the pit should have a distance from the residential building of at least 3-4 meters, since the formation of characteristic odors is possible.
  
• For simpler types of shower that will not be used with great intensity, it is enough to equip drainage well. It will be located directly under the shower. A hole is dug, 2 meters deep, a layer of rubble is poured at the bottom, and then a perforated plastic pipe is inserted. Material is poured into such a well, which will act as a filter. It can be gravel, crushed stone, old broken bricks, slag. The well is filled to the very top, then covered with a layer and covered with soil. From above, a wooden pallet is already installed on the formwork, which has slots for water seepage. This is the most affordable, but no less effective way that will provide the necessary outflow of water.
  

The easiest way to provide water is to install a plastic tank or an old iron barrel on the roof of the shower, paint it black to increase the rate of heating of water by sunlight, and connect a hose to it, through which water will flow into the tank. The presence of a hose for water supply is mandatory, especially if the tank volume is 100 liters or more. disadvantage tanks with natural heating is that in the cool season their use is problematic. Therefore, many prefer tanks With heated. There are three types of such systems:

Installation selected tank can be done in two ways - placing the tank directly on the cabin roof or on a special frame. The second case is rational to use if the volume of the tank is impressive, and the building may not support its weight. It is enough to make a frame from old iron pipes over the shower roof or from wooden beams. This method of placement will help to avoid significant heat loss and speed up the heating time of the water.

4. The simplest ways to organize a summer shower

It happens that the summer cottage is visited very rarely, and then, not for work, but more for recreation. In this case, the shower can be the simplest designs that you can even bring with you.

• Portable shower. This design looks like a large heating pad and is made of the same material. After filling the container with water, it is twisted with a special nozzle, at the end of which there is. At the opposite end there is a loop for which it is convenient to hang the container on a tree or a hook. By placing the container in a well-lit place, the water will heat up very quickly. The volume of such a "shower" is 10-15 liters. This entails restrictions on the duration of the reception of water procedures and the number of people who can use it. But it is a very convenient and inexpensive option for one person.
  
• shower rack- is an iron pipe on legs, which is equipped with a shower head and a hole for connecting a hose. Such a rack is convenient in that it can be placed in any convenient place and, if necessary, brought into a utility room for storage. disadvantage its is the lack of a water tank. That is, if there is no warm water and normal pressure in the system on the site, then you will have to take a cold shower.
• Usage shower system. The shower rack is a metal bar to which the overhead shower and faucet are attached. In order not to bother with the arrangement of a special room for its placement, many attach the shower system directly to the wall of the house or outbuilding. For this, water is drawn out of the wall. The wall of the building is protected from moisture. You can veneer it, or with other materials that are available. For convenience, you can separate the space with a curtain, and place a wooden pallet or rubber mat on the floor.

Keep in mind that this is an option for rare use. At the time when you will not be in the country, the system can be removed, and the outlet closed with a special plug.

All of the above types of showers are good because they do not require the arrangement of a foundation and a drain. But also the disadvantage is obvious- the possibility of their use depends entirely on weather conditions.

5. Do-it-yourself summer shower made of wood

To build a wooden building you will need:

• Appropriate timber;
• fasteners;
• Rubber hose;
• Shower head or shower set;
• Rubble.

Construction begins with the arrangement of a pit for water drainage. It is necessary to remove the top layer of soil with a depth of 30-40 cm and fill in the crushed stone. Thus, the soil under the shower will quickly absorb water, and the soap residue will remain on the rubble. Now you need to do formwork, to protect the wood from decay. At the corners of the pit, bricks are laid into the level. The height of the formwork must be at least 15 cm.

Now let's move on to building frame. You should start from the base. It needs boards 15 cm wide and at least 3 cm thick. The size of the base must match the size of the pit. For fastening boards, it is better to use threaded connections. Over time, the joints will not weaken even under significant weight, unlike conventional ones, which can "slip" out of the mounting hole. 4 beams with a section of 7 × 10 cm are attached to the base.

Bandaging of the frame performed using side and two transverse jumpers, which are inserted into the grooves. The same jumpers will strengthen the frame from above, which will ensure stability after attaching a heavy water tank to the roof. At your discretion, you can add a few more jumpers if you think that the design is unreliable.
For wall cladding you can use thinner wooden planks, clapboard, false timber, blockhouse and other timber. The main thing is to leave small gaps between the parts, 3-4 mm thick. This is necessary so that the planks can expand freely when wet, without deforming each other, and also shrink freely after drying. Remember that all wooden parts that will be constantly exposed to water must be carefully primed and varnished. You can soak them with drying oil or hot oil. Especially important before painting. There is a special antifungal antiseptic impregnation. You can start painting after the primer has completely dried.

When the shower is completely ready, you can hang tank. You can simply put it on the cross beams and secure with straps. If the tank is homemade, do not forget to cut a hole in the bottom for a watering can and a hole for the hose in the top. For convenience, several shelves for shampoos, soaps, etc. can be provided inside the cabin. and a couple of hooks for towels and clothes. Such a shower can be built over the weekend, and if the necessary materials are already available on the site, then the costs will be minimal. Life time wooden shower completely depends on how well you processed the wood and protected it from moisture before construction. Therefore, this point deserves special attention.

6. Polycarbonate shower enclosure

Polycarbonate is usually used to create. Therefore, for many, this material is associated with the greenhouse effect, and, consequently, with inconvenience. This opinion is erroneous. To create showers, there is a special, opaque type of polycarbonate. The most durable will be the building, which is made of metal profiles. Working with them is no more difficult than with wooden beams. A profile pipe with a cross section of 40 × 20 mm and a wall thickness of 2 mm is suitable for the construction of a frame. Also to you would need steel corner 50 × 50 mm. The number of profiles is determined depending on the area of ​​the future shower. The only thing to consider when cutting is that the racks should be 10-15 cm larger than the estimated shower height. This is necessary so that you can concrete them and not lose in height. Work plan will look like this:

• The assembly of the frame must be carried out on a flat surface. Two side drains and two overlapping crossbeams are laid on the ground. their straightness is checked. By welding, the parts are connected to each other. The second wall is assembled in the same way.
• Finished structures after welding must be installed vertically at the required distance from each other and connected to each other by two transverse profiles. Keep a 90 degree angle between the walls. It is necessary to fasten the transverse strips only on one side, on the other hand the door will be welded.
• After the frame is assembled, a hole of the required size is dug. The top layer of soil with a depth of 10-15 cm is removed, the concrete screed is leveled and poured. Once the screed has been poured and leveled, it is necessary to install the assembled frame on top so that the racks, which were originally longer, sink into. The level checks the verticality of the installed structure and adjusts if necessary. If the length of the legs exceeded the height of the concrete screed, it is necessary to hammer them into the ground until they are completely immersed.
• To collect water, you can install a special steel pallet or provide drainage ditches during concreting.
• For this design, it is better to use flat-shaped plastic water tanks. They are easy to install and, moreover, they will eliminate the need for arranging the roof.
• Separately, you need to weld the door frame and weld the hinges to the frame. It is more convenient to immediately sheathe the door separately from the walls.
• Sheathing the walls, fasten the polycarbonate directly to the profiles using self-tapping screws.

The color range of polycarbonate, which is used for sheathing shower enclosures, is very diverse. Therefore, the design can turn out to be very attractive. The care of this material is very simple, and in the evening it will protect you from the cool wind.

7. Country shower from corrugated board

Another good material for covering a summer shower is corrugated board. This material is highly strength and durability combined with ease. It is windproof. And when its walls heat up throughout the day, it will be comfortable to take a shower in it. Both wooden beams and metal profiles can be used as a frame. Metal, of course, is more durable. Therefore, if you still need to purchase materials, give preference to it.

The manufacture of the frame is similar to the examples from points 5 and 6. The only difference- more cross bars need to be added. This is necessary to securely fix the sheets and give the structure rigidity, since the corrugated board itself is considered a soft material. Attach sheets with . Be sure to use spacers to avoid damaging the sheet. You can cut the corrugated board with scissors for metal or using a grinder and a disk with teeth. Other circles are not recommended. During cutting, the polymer coating can burn through, which protects the coating from corrosion. The roof is also covered with corrugated board, and the tank is located under it. The gap between the walls and the tank will provide natural ventilation in the cab and prevent the formation of unpleasant odors. An unheated tank can be placed on top of the frame. Then the need to build a roof is eliminated.

8. Brick shower

This is the most labor-intensive design that is found in summer cottages with year-round living. Benefits such a soul has a lot:

• With the proper approach to the construction process, such a shower will last for many years;
• If you use a heated tank, you can take water treatments at any time of the year. Windproof walls also contribute to this;
• It is very easy to insulate such a building by sheathing it with foam plastic on the outside;
• A brick shower can consist of two zones - wet and dry, where it is much more convenient to change clothes;
• A brick shower can be combined with a toilet and use one drain hole;
• Strong walls and a concrete foundation will allow the use of very large water tanks without the risk of structural failure.

The disadvantages include the high costs associated with the purchase of materials and the duration of the work.

It is necessary to start construction with the arrangement foundation. Marking is carried out on the selected site and a trench is dug along the perimeter with a depth of 20 cm and a width of 40 cm. Now it is necessary to fill the trench with crushed stone or broken bricks and pour concrete with a liquid mortar so that it seeps through the stones. After the mortar dries and sets, after about a week, you can start laying the first layer of bricks. When laying, be sure control verticality after each new row. Don't forget to leave room for the door. Laying the last layer of bricks, make mortgages from thick wooden beams. A tank will be attached to them, and a roof will be laid. It is also necessary to strengthen the doorway with a metal corner or the same beam. The roof is covered with corrugated board. It is also necessary to provide a small window that will provide lighting and ventilation.

Now we need to arrange drain. It is best to equip a drainage well under the shower and lay a drain pipe from it into the sewer pit. Then a large number of people can freely use such a shower. The drainage well is covered with earth and poured with concrete, the drain pipe is first brought out. To facilitate the drain, you can fill in a slight slope towards the middle. In this case, the upper edge of the pipe must be flush with the floor. A wooden pallet with holes is laid on the concrete floor.

Optimal tank size is at least 200 liters. When placing it on the roof, provide a hole for the inlet pipe, on which the shower head will be screwed. It can be both purchased and homemade. When using a heated tank, do not forget about the supply of electricity. If you are not strong in this matter, then for your own safety, seek advice or help from specialists. Door leaf can be made of wood or OSB or chipboard sheathed with galvanized sheet. Thus, you will provide yourself with comfortable conditions for taking water procedures at any time of the year.