The topic of today's article is what doors are put in the bathroom and toilet. At first glance, everything seems quite simple, you just need to choose a design, the width of which will be slightly less than that of interior partitions. But in practice there are many other nuances that will have to be taken into account. Let's talk about them.

The standard width of the door to the bathroom is 55-60 cm

We select a moisture-resistant door to the bathroom

The design of any partition is approximately the same: frame, filling, exterior finish. Most often, MDF or an array of budget tree species are used to create the base. Which doors are better for the bathroom and toilet, everyone decides for himself, but keep in mind that all of the listed materials are prone to moisture absorption. The average indicator of moisture resistance is the ability to install doors in bathrooms with humidity up to 60%.

If the percentage of humidity exceeds the specified limit, then it is better to stop at the doors made of solid alder or oak.

Moisture resistance depends on several factors. The first one is the area of ​​the bathroom. If it is large enough to accommodate not only a bathtub (or cubicle), a sink, a washing machine, but also some furniture, then it is unlikely that condensation will accumulate in it. In rooms with an area of ​​\u200b\u200bless than a few square meters, it can be difficult to achieve complete removal of fumes. In addition, there is a high probability of a direct splash of water on the door, which means that it should be protected much better.

If you are considering which bathroom and toilet doors are suitable for your home, pay attention to the weak points of almost all designs:

• Leaky joints. Since the protective coating is applied first to the surface of the door, and then to its edges, joints are formed between them. And although they are invisible at first glance, moisture still seeps through them.
• Unprotected ends. Even on the most expensive models, protection of the upper and lower ends is rarely provided. Vapors penetrate through them and accumulate inside, leading to damage to the canvas. It is not difficult to deal with this - it is necessary to cover these places with a protective varnish.

Doors with a frame made of chipboard and MDF are less resistant to moisture penetration than products

How to choose a door to the bathroom and toilet - coating materials

We list the characteristics of different coatings used for surface finishing. So it will be easier to figure out and navigate from what material to put the door to the toilet and bath.

Laminate

The laminated coating is a paper impregnated with special resins. Protects against the penetration of vapors at humidity levels up to 60%. High-quality and expensive laminate is resistant to damage and wear. Cheap models are pasted over with a poor quality coating that is easily scratched and torn. As a result, water gets inside.

For better protection, you can put doors covered with laminate. This material is an improved version of laminate - thicker paper and several layers of varnish

PVC film

A PVC film is applied to a wooden frame or MDF structure. It is absolutely impermeable to moisture and has good resistance to damage. To clean it, you can use various chemically active substances without the risk of spoiling the surface of the door. Therefore, when considering which door to put in the bathroom, check out several similar models.

The palette of shades of this coating is quite wide, you can easily find a model for any bathroom design. Among the shortcomings, it is worth noting the possibility of delamination of the door leaf and the presence of chloride in the composition of the film. True, as the manufacturers assure, it is always within the normal range.

Veneer

When deciding which door to choose for the bathroom, do not ignore wooden structures. A frame made of inexpensive wood or chipboard is covered. With proper coating of the leaf with a helmet, varnish or vitreous enamel, you can safely install the door on a wooden frame. With constant high humidity, it is better not to take risks and purchase a door with a chipboard base.

Although veneered coating is considered very expensive and representative, it is not always advisable to use it in the bathroom.

Ecoveneer

When answering the question of which doors are better to put in the bathroom, we cannot ignore the eco-veneer. It is wood fibers bonded with polypropylene. This material is environmentally friendly and safe for the health of adults and children. do not emit harmful compounds into the air, so they can be installed in homes where allergy sufferers live.

Ecoveneer is an obstacle not only for the passage of moisture, but also for air. Therefore, in such rooms it is necessary to consider the installation of ventilation.

Another advantage of eco-veneer is its increased strength, the door leaf is difficult to damage.

As you can see, in order to correctly calculate which doors are better for a toilet or bathroom, several aspects need to be taken into account. The dimensions of the rooms, the level of humidity, and, of course, the choice of material for covering the door leaf are important here. Milano consultants will help you with all these questions. Contact us at any time.

The bathroom and toilet are rooms in which there is a characteristic microclimate. High humidity, temperature changes are factors that adversely affect the interior door leaf. Therefore, we often ask ourselves: which door to put in the bathroom? At the same time, I want the product to last a long time and maintain an aesthetic appearance. In addition to these criteria, the combination of an interior product with the style of the room and the apartment as a whole is considered important.

Choice of bathroom door material

The decisive factor in deciding which doors are better to put in the bathroom is the area of ​​\u200b\u200bthe sanitary unit. The level of air humidity directly depends on this criterion. In a small room, the humidity level will be high. This factor will be exacerbated if the ventilation in the room is either absent or weak.

If you are thinking about which door is better to install in the bathroom, you can choose from the following options:

• wood or wood veneer;
• polymer-coated doors (laminated, with PVC film, covered with eco-veneer);
• plastic models;
• glass products.

Each of the materials or types of product coatings is characterized by its pros and cons.

What criteria should be followed when choosing?

In the question of which doors are placed in the bathroom, consultants recommend focusing on the characteristics of the bathroom. If the humidity level in the room exceeds 60%, experts recommend paying attention to materials that are alternative to traditional wood and the usual wood derivatives. In this case, it is better to give preference to plastic and glass. If the room has a large area, is equipped with sound ventilation, then you can install solid wood doors, veneered, laminated or enameled.

Of great importance in the question of which door to put in the bathroom is the type of protective coating applied to the door leaf and edge. In the manufacture of some models, the following technology is used: the film is applied first to the canvas, and then to the edge. A joint imperceptible to the eye is formed, and if it is leaky, then moisture will penetrate in this place and the canvas will deteriorate over time.

When making a door from a hygroscopic material (wood and its derivatives), the upper and lower ends are usually not covered with a moisture-proof film. These weak areas will attract and store moisture from the bathroom. When choosing doors to the bathroom made of wood, they must be covered with a hydrophobic varnish without fail.

Laminated products

Affordable, they are made from a base and paper glued to it by means of resin. The coating of poor quality is easily damaged and moisture penetrates in places of damage. Laminatin has the best consumer characteristics. It has a large layer thickness and is varnished in several layers. The cost of such a product is higher than laminated counterparts, but laminate interior doors are durable and withstand humidity of 60% or more.

PVC Coated Models

The frame of such products is made of MDF coated with PVC film. The coating gives the door water-repellent properties, so they can be washed with the use of sanitizers. A big advantage of such products over plastic counterparts is a wide range of colors and textures. The disadvantages include the possibility of delamination of the web with subsequent ingress of moisture into the structure, as well as the presence of chloride in the composition of the film in small quantities. If choosing a bathroom door is a safety aspect for you, then avoid buying products with PVC film. At elevated temperatures, chloride is released into the environment, so the PVC coating is not environmentally friendly.

Eco veneer doors

Eco-veneer is a new generation bathroom material, a product of the fusion of woodworking industry waste and polymeric plasticizer. The latter is harmless and environmentally friendly. On the outside, the eco-veneer is indistinguishable from natural material. However, in terms of consumer qualities, eco-friendly veneer is superior to natural veneer. It is resistant to moisture and mechanical impact, aesthetic and does not emit harmful substances into the atmosphere even at elevated temperatures, it is well suited for the bathroom. The only downside is poor soundproofing.

Wood or veneer products

Wooden products are rarely installed in bathrooms due to their high hygroscopicity. However, if there is a coating of good varnish, paint, these models can last for decades.

The frame of the doors with veneer trim is made from inexpensive (soft) wood or chipboard, and the exterior trim is made with a thin cut of valuable varieties. Veneered products look very respectable, but they are not resistant to moisture. Therefore, if the level of humidity in the room is high, then it is not recommended to install models with veneer trim.

Plastic doors

They are affordable because they are made from inexpensive raw materials. The cavities of the product are filled with expanded polystyrene. Plastic models are absolutely hydrophobic, not afraid of temperature changes, biological effects of fungus and mold. In addition to these advantages, plastic doors provide good sound insulation and prevent heat transfer.

The disadvantages of these products are their uniformity and unrespectable appearance. Basically, interior doors made of plastic are made in a standard shape, size and painted white. In addition, when in contact with high temperatures, plastic begins to release chloride, which is why it is considered an environmentally unsafe material.

glass models

They offer the highest performance and are ideal for installation in the bathroom. Glass doors look unusually beautiful, give the room lightness and increase space. Modern tempered glass or triplex is not afraid of mechanical impacts, they can be washed using chemicals. If you are in doubt about which door to install in the bathroom, give preference to this material.

Glass is absolutely safe from an environmental point of view and a good material, and new technologies for the production of products from this raw material exclude the possibility of injury from fragments. Even with a strong blow, the door will not shatter into fragments, you will only see a network of cracks inside the polymer film. The disadvantage of a glass interior door is its high cost and heavy weight, which means forcing the opening and choosing durable fittings. For aesthetic reasons, frosted glass models should be chosen in the bathroom.

What are the best doors for bathrooms?

From the abundance of models of interior doors, it is sometimes very difficult to make a choice. The comparative characteristics of various products presented in the table will help you decide which doors are best for the bathroom:

Conclusion

When deciding which doors to put in the bathroom, you need to decide which of the criteria is most important: respectable appearance, moisture resistance, resistance to mechanical wear. Glass doors are a versatile option. They meet all the criteria, but have a lot of weight and cost. More budget options are doors coated with eco-veneer, laminate, veneer. Plastic doors and PVC-coated products have a potential health hazard as chlorine is released in hot environments. Wooden products are not recommended for installation in rooms with a humidity level above 60%.

Many people prefer to install the same interior doors throughout the apartment or private house.

However, in the case of a bathroom, it is better to put aesthetics at the expense of practical properties, to choose strength and reliability.

What are the features of bathroom doors and how to choose them?

The bathroom is a room where moisture often appears. And also this is a room where the air is maximally saturated with its vapors. Therefore, you should purchase and install a door that can withstand this effect, in particular:

• It makes sense to choose and install a model that will not deteriorate from moisture, changing its appearance;
• Do not put a product that will be saturated with vapor, thereby deteriorating its strength;
• Which will be convenient to use.

For example, you should not install an MDF door, the best available in the price-quality category, in which case it will be impractical and will quickly become unusable.

Even if the manufacturer indicates that the proposed product is able to serve its owner faithfully for many years, you should not believe in it. You should first find out how true this is.

So, it is worth checking how the material used as the basis for the canvas is not susceptible to moisture, steam, and rare temperature changes. And if the material is able to resist these effects to a lesser extent, you should not purchase doors made from it.

Whatever the coating, its properties and characteristics, such a model will last much less than a sample made of a material that is able to ignore the effects of temperature, steam or moisture. Such a purchase will be much more economical.

Why you should not put MDF doors in the bathroom and what problem do they imply?

MDF is ideal for a room, but not for a bathroom. It is better to put any other product, choose a model from a different material.

There are a lot of reasons for this: first of all, it is worth remembering that MDF is paper, albeit pressed, durable and looking aesthetically pleasing. But like a sheet of paper, or a newspaper, and an MDF door is very susceptible to moisture.

The consequences of using such a door in the bathroom will be visible after a few weeks. The first sign will be a swollen box, or even a canvas. The next step will be the disappearance of the gaps (at the beginning it will be convenient for the user to close the door - the canvas will fit snugly against the box, then some effort will be needed, and finally the last step - it will not be possible to close the door).

The reason for this may be that the canvas can be laminated (and a certain protection against moisture, respectively, is present), but the door frame, as a rule, is not processed in any way, and even more so, it does not have laminated protection.

Even if you purchase a door that has a laminated coating that guarantees protection from moisture, you should think about how long such a coating can last - during operation it quickly becomes unusable.

Numerous scratches, small bumps, exposure to temperature will sooner or later violate the integrity of the coating and then the process described above will begin - saturation with moisture and damage to the door.

Accordingly, MDF doors are the worst possible purchase, which you should not make. It is better to look for other options - those that can last much longer.

Wooden models: what are the difficulties with them?

Wooden doors have been popular for a long time. For the bathroom, they are quite comfortable and practical, so it makes sense to choose them.

Such a property as the “breathing” of wooden doors will be very useful. This feature means that the tree will give off excess moisture absorbed into the air during operation and take moisture away if the air is oversaturated with moisture (which is much better than in the case of MDF).

This ability is so obvious that the user can detect changes in the design (changes in dimensions, weight, volume, etc.).

It is for these purposes that the canvas of wooden doors is varnished, or (which is much better) painted over with paint. At the same time, when installing the door frame, anchors and mounting foam are used to seal openings (this is necessary just in case of oversaturation with moisture, when the tree begins to swell and it needs room to expand, without harm to the canvas or ease of use).

If you use other methods of fastening, there is a possibility that the frame will lead, i.e. aesthetics will be violated, it will be inconvenient to use such a door, if at all possible. Therefore, it is better not to experiment and not to check what other options there are.

It should also be borne in mind that the more cycles of absorption and release of moisture, the lower the strength of the door becomes. Summing up, it should be said that a wooden door is not the best, but not the worst option available. However, the durability of such a solution leaves much to be desired, but the aesthetics are at a high level.

One of the newest and most convenient options for the bathroom is metal-plastic doors. Their advantage is strength, durability, reliability, practicality and convenience. Aesthetics should also be noted (such doors can be solid, or with glass inserts, and of any size and shape).

The main advantage of this solution is the practicality of the material from which the door is made - aluminum and ordinary plastic. Both of them are absolutely not susceptible to moisture. In addition, plastic is more convenient to use and maintain - it is easy to wash, easy to maintain the primary appearance.

Some nuances of choice in the following video:

The advantage is the fact that a variety of color options are offered on the market today - it can be a classic white color and shades for various types of wood (thanks to which each buyer will be able to purchase a product that will either look very similar in appearance or will fully match the color other interior doors installed in the house).

The durability of this material is also a weighty argument in favor of such a choice - all fittings can be easily replaced, it will be difficult to damage the door, and besides, metal-plastic is not susceptible to both moisture and temperature changes, steam, etc.

A metal-plastic door will allow everyone to choose an option to their taste, in addition, such doors do not require much time for maintenance, which is why they are the best and most convenient option for a bathroom.

Doors for toilet and bathroom - choice, reviews, characteristics

Doors are equipped with any premises in houses, however, as practice shows, owners have great difficulties in choosing solutions for bathrooms. The reason lies in the specific operating conditions of baths and toilets, especially when it comes to changes in humidity and temperature. Based on this, it is worth concluding that not all doors are suitable for bathrooms, and therefore a reasonable question arises: how to choose a worthy solution?

Filling and coating options for bathroom and toilet doors

Today's market is literally replete with numerous offers from manufacturers offering door leafs to bathrooms and toilets with various coatings. When determining a rational solution, it is worth proceeding from what material the door is made of and what size the room has.

Consider the following situations:

• when placing plumbing, there is sufficient space to the canvas: most likely, splashes will not fall on it, therefore, it can be made of various materials;
• when placing sanitary ware, it is not possible to take more than one step: due to the limited space in the room, high humidity will be observed, therefore, it is necessary to consider solutions from the appropriate material and method of finishing.

Any door leaf has an internal frame and provides for exterior decoration. As the basis of the frame, manufacturers prefer an array of "budget" wood species, chipboard and MDF. Such materials are able to withstand moisture if its level does not exceed 60%. In other cases, experts recommend considering glass and plastic doors.

The ability to endure humidity depends on the quality of the protective coatings, internal filling and frames. As practice shows, the most vulnerable canvases, for the manufacture of which an array of wood is used, the most stable doors are structures made of chipboard and MDF.

Effective door coverings - how to choose?

Some manufacturers, when applying a protective layer on the door, first cover the canvas with it, and then the edges. As a result, inconspicuous joints are formed, which are often not airtight. Moisture entering through them gradually destroys the canvas, rendering it unusable. It is best if the upper and lower ends are not covered with protective materials, but a special varnish is applied to them.

The most optimal coatings that can protect canvases from moisture:

Bath doors Laminate

Laminate: this variety attracts numerous buyers with a reasonable cost. The paper is glued to the base of the canvas, pre-coated with resin. The resulting laminated doors, according to manufacturers, are ready to withstand humidity, the level of which does not exceed 60%. When choosing a canvas with such a coating, it is worth considering solutions offered by manufacturers with an excellent reputation. In other cases, it is possible that low-grade thin paper will be used for coating, which is prone to damage under minor mechanical stresses that are typical during the operation of doors. Moreover, moisture penetrates through the formed cracks, causing the canvas to swell.

Laminate - a coating similar to the previous version, with the exception of the thickness of the paper used and the application of a varnish coating in several steps. Laminate is a more expensive material, respectively, the price of finished doors will be higher than that of laminated counterparts.

PVC bath doors

PVC. In this case, manufacturers use frames made of MDF and wood for canvases, after which they cover them with a wear-resistant PVC film, which cannot be harmed by chemically active substances. It can be dyed in any color and have a different texture, which allows buyers to choose the canvas tone on tone. The composition contains chloride, the content of which in the composition of the paint is strictly maintained within the permissible limits and is absolutely not dangerous for people. Also a certain disadvantage is the tendency to delamination.

Eco-veneer bathroom doors

Ecoveneer is a plastic coating made using a special technology using wood fibers and plastic compound as a binder. The material is environmentally friendly and does not emit hazardous substances even when the air temperature rises. Eco-veneer in structure resembling wood differs from the latter in greater strength, wear resistance, and resistance to moisture. Budgetary wood species or chipboard are used as internal filling, and fine wood veneer is used to cover the top. Wooden doors are “afraid” of moisture, but if you use protection for the canvas (lacquer, enamel, paint), then this factor will not harm them. If there is high humidity in the bathrooms, then experts advise giving preference to veneered chipboard models.

Choice of door material

Plastic door panels for bathrooms and toilets are currently in high demand among consumers who find this solution one of the best for use in bathrooms where the humidity index exceeds 60%. For their manufacture, inexpensive durable material is used, on which mold and fungi do not form. Expanded polystyrene is most often used as a filler, providing excellent sound insulation and thermal insulation. All materials used in the manufacture of plastic doors are not susceptible to moisture. It would seem that such canvases are ideal, but, in fact, they also have disadvantages. First of all, this concerns the presence of chloride in the composition (only certified products have an acceptable amount), and secondly, the lack of a choice of color (all products are white).

Glass doors are the perfect solution. The material used in the manufacture, in comparison with others, is characterized by excellent practicality and presentability. Glass doors are not affected by a number of negative factors inherent in the operating conditions of bathrooms and toilets, but they have a significant weight, therefore, only high-quality fittings are allowed during their installation.

Door leafs made of chipboard and MDF are distinguished by functionality and durability. Such solutions demonstrate excellent resistance to water, high temperatures and other factors that can cause damage. Affordable prices for doors, a wide color palette and a decent range of sizes, coupled with decent quality and performance characteristics, make them an excellent option.

Natural wood door panels are perfect for any design. Ecological cleanliness and noble appearance are key advantages, however, despite these positive qualities, they are afraid of moisture and water, from the impact of which they are deformed, respectively, they will not last for a long time in conditions typical for bathrooms.

Metal-plastic doors guarantee effective heat preservation, perfectly tolerate temperature loads and mechanical impact. Cloths, even after long-term operation, are ready to boast of their original presentability and the preservation of high-quality properties and functionality. Unique characteristics make metal-plastic doors an excellent solution, but the cost of such models is quite high.

Determining the best way to open the door

The modern market offers consumers doors that provide for various opening methods, namely:

• hinged plan (classic opening method): such canvases allow the use of a threshold during installation, which increases heat and sound insulation. The disadvantage of this solution is the need for free space, sufficient for its opening - closing

• sliding plan: such solutions contribute to significant space savings, however, mounted canvases leave gaps between the floor and the door, respectively, you should not count on good sound and heat insulation. If, nevertheless, there is a desire to use just such a modification, then experts advise considering cassette plan models, where the above disadvantage is practically reduced to "no";
• folding plan: doors of this variety do not require additional space when opened. By design, they are divided into books and harmonicas. The first models are represented by two halves, and the second by three or more elements. The disadvantages of such doors are poor soundproofing and absorption of most of the doorways when they are folded.

Features of glass doors for bathrooms

Modern doors surprise with a variety of design solutions and decor. One such variety is the glass insert. When choosing a canvas, you should not forget about such a factor as their transparency. Of course, frosted or tinted glass is more appropriate for bathrooms, since in this case the visibility of this level is enough to understand that the bath or toilet is occupied. Glazed doors are presentable, while there are no restrictions or tips for choosing. In this situation, the buyer is guided only by personal preferences and financial capabilities.

On the practical side, attention needs to be paid to a number of the following factors:

• sound insulation: only a thick and dense canvas can provide the absence of noise. When considering glazed doors, it is important that the inserts are multi-layered (triplexes with 2 or 3 layers);
• the ability to determine if there is anyone in the bathroom: this factor is relevant for a large family, so canvases with decor in the form of glass inserts will solve the problem perfectly.

Ventilation windows for doors

The need for installation of ventilation windows in the door is not available in all cases. So, if, after taking a bath, condensation forms on the wall and canvas, the mirror fogs up heavily, then you cannot do without such a window. Excessive humidity is the cause of insufficient natural ventilation of the room, and if it is not removed forcibly, then the door will soon become unusable.

The installation of ventilation windows allows you to reduce the formation of condensate, due to the equalization of the temperature of the air and the web, through forced ventilation. Their installation involves drilling the door leaf, respectively, it is best to do all the work before the canvas is put into place.

ventilation windows various design solutions are offered on the market, but the highest demand is for products:

• in the form of a lattice. Rectangular design with curtains located at an angle. For the manufacture of metal, PVC and plastic can be used;
• in the form of rings. Products are usually made of plastic. To absorb noise, special meshes are mounted in the structure. Usually 4-5 rings are installed in the canvas.

For greater efficiency in the fight against condensate, it is recommended to install a fan in the ventilation openings. This solution will speed up air circulation and mixing of hot and cold layers. Fans can be automatic and manual, while each consumer designates the type of operation of the unit independently, based on personal preferences.

With problematic air removal, experts recommend organizing forced ventilation, which involves pumping air into the bathroom from the outside and circulating it as a result of the pressure difference. In the absence of the possibility of organizing the natural movement of air masses, ventilation of a mixed plan will act as a rational solution. It involves the intake of fresh air from the outside through one channel and its output through the second.

Selection of accessories for door panels in the bathroom

Fittings - decorative and functional products, the installation of which allows you to make use convenient. When choosing doors, handles and locks deserve special attention. Consider the solutions that manufacturers are ready to offer today, as well as their advantages and disadvantages:

• pens with built-in lock - an economical solution. Represented by a conventional handle, inside which a latch is installed. One position allows you to fix the mechanism, eliminating rotation. Installation of such fittings is simple and requires drilling only two holes;
• separate clamps: in this case, you will need to purchase a door handle and a mortise or invoice latch. When using the latter, valves are installed instead of locks - an unpretentious and reliable solution with an unlimited service life;
• plumbing locks(standard). The traditional design has one tongue, which is responsible for fixing the door when closing and locking it in the open state by means of a latch. The principles of operation of locks with built-in latches and plumbing locks are similar, but the latter are more reliable.

When choosing the type of lock for the canvas in the bathroom, you should proceed from its reliability, while families with babies and the elderly should consider options that have special openings for emergency opening.

Platbands are integral components for hinged doors, while choosing them, it is worth focusing on the driving angle.

The 45-degree option is a morally obsolete solution that will spoil the stylish design and will not be able to convey the entire presentability of the canvas. Currently, the actual setting of the driving angle is 90 degrees. Using such platbands it is easy to emphasize a stylish design. For consumers who want to create a spectacular door, the market offers capitals and cornices as framing. Decorative elements add solidity and presentability. Recommended for decorating doors in a classic interior.

An important structural element of the doors are the hinges, through which the canvases are hung. They are expressed and hidden. The loops of the first type are ideal for classic canvases, the second - in modern and high-tech style. It is worth noting that not all hidden hinges will allow you to open the doors more than 90 degrees, so when choosing, you will need to ask the manager about this issue.

Choice of canvas by color and style

Each owner wants the interior to be complete and concise, so when faced with the need to choose a door leaf for a bathroom, it is worth taking into account that the canvas must simultaneously correspond to the internal (bath or toilet) and external (corridor) design.

All doors for bathrooms can be classified by style into the following groups:

• modern: a group that is represented by modern door leafs, recognizable by straight chopped lines and a slight “rounding”;
• high-tech: a group that includes canvases with sharp straight lines and a futuristic design. Doors of this style are decorated with glass;
• classic canvases with unobtrusive design will be ideal for any design solution in the interior.

Modern door collections amaze with a variety of colors and shades, and, of course, every buyer knows that it must be selected, first of all, so that it harmonizes with other interior items and its style.

What door to put in the bathroom so that it does not deteriorate from high humidity, is durable, reliable and beautiful? Not every material will be able to withstand the specific conditions of service without consequences, so it would be impractical to choose a door, guided only by its compliance with the interior. Let's figure out which doors are better to put in the bathroom according to the type of construction, material and external design.

Wood MDF Plastic
Glass Mirror Stained Glass

To withstand the operating conditions in the bathroom, the door to the bathroom must be resistant to high temperatures and humidity, provide good air exchange and sound insulation, and have antiseptic properties. What materials will meet these high requirements?

natural wood

Solid wood bathroom door is a good choice if it meets the following requirements:

• has an external water-repellent coating of paint or varnish;
• treated with antiseptics;
• made of hardwoods that absorb moisture poorly (beech, oak, mahogany).

It is important to properly install the door block. So that the box does not warp over time from constant exposure to hot steam and water, it is fixed using anchors and mounting foam. If these conditions were met during selection and installation, its further durability will depend on proper care. From constant humidity and evaporation, the outer protective coating loses its properties, and it must be updated from time to time, otherwise cracks may appear on the canvas.

Covering from MDF or fiberboard

Manufacturers of doors made of MDF and chipboard assure that the products are absolutely not afraid of moisture. In fact, the construction consists of a frame made of pine, which is characterized by high hygroscopicity. The design has water-repellent properties due to the outer finish of the canvas: the laminated coating is resistant to moisture, but until chips and scratches appear on the surface. There are other vulnerabilities: the back of the box, for which water-repellent protection is not provided. In just a few days of operation, the wood can swell, and the door will no longer close completely.

Products made of MDF and chipboard have an affordable cost, a wide range of models and a variety of colors - these are their main advantages. To ensure their long service life, it is necessary to treat all open areas of the box with a protective compound, make sure that the edge of the leaf is glued with high quality and has no gaps, and protect the surface of the door from damage.

metal-plastic

If you are going to purchase doors to the bathroom and toilet, and doubt which ones will last better and longer, take a closer look at metal-plastic structures. Aluminum and plastic, the main components of these doors, have a lot of advantages:

• resistance to moisture, temperature changes and cleaning agents;
• strength and durability;
• resistance to deformation;
• simple hygiene care;
• lack of a nutrient medium for putrefactive bacteria and fungi;
• low cost.

Choosing a door to the bathroom with a design similar to other designs installed in the apartment will also not be difficult: the exterior decor of metal-plastic PVC film allows you to get any color and texture.

Glass

Glass door - very good an option for the bathroom, given the resistance of this material to moisture. There will be many disadvantages of such a design:

• When hot water is turned on, the glass surface is constantly covered with condensate. Moisture flows down the smooth panel, accumulates in puddles on the floor and leaves stains.
• Water stains, splashes, fingerprints are very clearly visible on the glass surface, therefore, such doors need constant hygienic care.
• Glass is a fragile material, and if it is broken, it is also dangerous. So that in case of damage to the glass door it does not crumble into small fragments, the surface is protected with a special film, and this affects the increased cost of products.
• The low level of sound absorption is another drawback.

The design of glass doors is very diverse. It is customary to install deaf structures in the bathroom, so designers solve the issue of glass transparency in various ways: they create stained glass drawings, spray paint, paste over with a film or matte.

Types of doors by opening method

Swing Sliding Folding

What is the best door to put in the bathroom according to the method of opening? Manufacturers provide several designs to choose from.

• A swing door is the usual standard option, quite convenient, if only square meters allow. The design consists of a box and a sash attached to it with hinges. Provided that the bathroom is usually modest in size, the door leaf opens outward. This saves space in the bathroom. It is necessary to install such a door taking into account that it does not block free access to other rooms in the open state.
• A sliding door does not require additional space in the room, but for it it is necessary to leave a free part of the wall where the sash will move. There is another option: equip a groove inside the wall where the sash will go when opened. In this case, the door will not interfere with the use of free space.
• The folding design "book" or "accordion" has the only drawback - poor sound insulation. This design is compact and takes up minimal space when opened.

Color selection

What color to choose doors for the bathroom and toilet? The entrance to the bathroom, kitchen and rooms is usually located in the hallway. To avoid color dissonance, the most rational solution is to choose the same shade for all designs. If the door block delivered to the bathroom is made of a different material, care must be taken in advance so that the decor of the doors harmonizes in color with the interior. It can be a colored textured PVC film, a similar pattern on glass and similar fittings.

Hardware features

Choosing the door to the bathroom, you need to take care of suitable fittings. These are hinges and a latch handle. It is desirable that the design of the chosen option matches the fittings installed on other doors of the apartment. To check the quality of products, you should pay attention to the following points:

• Door hinges should not creak. High-quality fittings open smoothly, but with little effort.
• A lock with a magnetic latch has a shorter service life compared to a mechanical one. Pay attention to the tongue of the lock. A plastic tongue creates less noise when closing than a metal one.
• You can determine the quality of a door handle by its weight. The iron core, which is characterized by a long service life, is much heavier than the unreliable silumin - the material for cheap Chinese products. The handle spring must be elastic.
• In order for the door to be locked from the inside, the handle must have a locking device. More reliable in operation is the option when the latch is included in the handle kit, but is located separately during installation.

All door hardware should be covered by a warranty. If the store refuses to issue a warranty card, it is better to refrain from buying.

Rating of manufacturers

Before choosing the doors to the bathroom and toilet, we suggest that you familiarize yourself with the rating of manufacturers.

• "Alexandria Doors"- Ulyanovsk factory. Modern equipment from Germany and Italy allows us to produce products of European quality.
• "Volkhovets". The doors of this brand are produced in Veliky Novgorod. Buyers are provided with a very wide range of products in a variety of styles.
• "Dera". For more than twenty years, the Penza company has been producing its products. The manufacturer offers a unique design, high quality and affordable prices.
• "Stendor"- practical, elegant, durable doors from St. Petersburg. The factory is equipped with imported equipment.
• "Sophia". The Tver factory recently upgraded its equipment. Products are made in accordance with international standards.

World famous foreign brands:

• Tre Piu is an Italian company. It offers non-trivial models with finishing elements made of aluminum, impact-resistant glass, veneer, precious woods.
• Garofoli- a huge range of models from the Italian manufacturer.
• Dana is an Austrian company. It has been supplying its products to the world market for over 40 years.

Products of well-known manufacturers are characterized by decent quality. The durability of the product depends not only on how to choose a door, from what material, and from which manufacturer, but also on the correct installation work, timely hygienic care and careful handling.