Series p 44t. Houses of the p44t series, apartment layouts with dimensions. Exterior finish and design features of the series

The P-44T series has become one of the most demanded housing projects on the market of new buildings in the capital and in the Moscow region. Houses of this type were actively built up both in new areas (Lyublino, Northern Butovo, Novokosino, Maryinsky Park), and places of demolition of dilapidated housing stock in areas of old buildings (Medvedkovo, Lefortovo, Shchukino, Southern Chertanovo, etc.). In total, about six hundred houses of this series were built in Moscow, and about two hundred in the Moscow region.

Houses P-44T compare favorably with the buildings of the basic version P-44 (built before 1999) with glazing of loggias, the presence of half-windows and bay windows, improved thermal insulation of exterior panels and an improved water supply system, and placement of an air vent in the hallway.

In general, the houses of this series are considered to be a very successful engineering and architectural project, they meet international standards for fire safety and capitalization (1st class), and therefore continue to be actively built at the present time. The strength of the construction of houses is also evidenced by the fact that the developer indicates "100 years" as the estimated life of the house. An attractive combination is the relatively low cost of square meters and a fairly high level of comfort, as well as the high speed of construction of apartments of the P-44T series.

Exterior finish and design features of the series

The P-44T series of multi-section houses is easily recognizable by the aesthetic “brick-like” finish of the facades, which ennobles the appearance of the concrete structure. The exterior decoration of the house is usually done in dark orange or light sand colors, and the decoration of the lower floors, bay windows and half-windows in gray and white colors.

The indisputable advantages of high-rise buildings of the P-44T series are: a high level of sound insulation in the outer panels, the presence of individual regulators for heating devices, modern fire-fighting systems, devices for warning about fires, floods, responding to the opening of the doors of the technical floor, basement, electrical panel, elevator shaft). Due to the fact that concrete panels have the most even surfaces compared to panels in other high-rise buildings, the cost of interior decoration of apartments is significantly reduced.

However, some reviews indicate that in new houses, during shrinkage, cracks form at the joints of the panels and sometimes depressurization of the “seams” occurs. Therefore, when buying an apartment, you need to pay attention to the quality of the installation of panels.

Features of apartment layouts

As in most modern new buildings, the rooms in P-44T houses are isolated. In addition, in some houses built according to this project, apartments are also located on the attic floor, which is attractive to many potential property buyers.

The spacing of the transverse walls has been increased to 4.2 m, and the thickness of the internal walls - 14 cm and 18 cm, provides good sound insulation between rooms. Apartments have separate bathrooms (with the exception of shared bathrooms in one-room apartments). Available for purchase of an apartment with a finished municipal finish.

The disadvantage of P-44T, like other panel houses, is the presence of a large number of load-bearing walls inside the apartments, which does not allow redevelopment at the request of homeowners. It is strictly forbidden to cut window sills or make openings in load-bearing walls in houses of this series.

Specifications

Igor Vasilenko

P-44T series

Years of construction: from 1997 to present time

wall material: brick faced panel

Number of sections (entrances): 1-8

Number of floors: 9-25, the most common options are 14, 17

Ceiling height: 2.70-2.75 m.

Elevators: passenger and cargo-passenger, in 20-25-storey sections (entrances) - 2 cargo-passenger and passenger

Balconies: glazed balconies in 1-room apartments. Glazed loggias and bay windows in 2- and 3-room apartments (there are also half-windows in the end and corner 2- and 3-room apartments)

Number of apartments per floor: 4

Panel houses of the P-44T type series in Moscow were built as in new areas of mass development: Maryinsky Park, Northern and Southern Butovo, Solntsevo, Mitino, pos. Severny, Novokosino, Novoe Kozhukhovo, Nekrasovka, Zhulebino, Lyublino, and in the old areas where mass demolition of five-story buildings, dilapidated and uncomfortable housing was / is being carried out: Shchukino, Zelenograd, Khovrino, Beskudnikovo, Koptevo, Sviblovo, Medvedkovo, Izmailovo, Lefortovo, Perovo, Nagatino, South Chertanovo, Zyuzino, Cheryomushki, Kuntsevo and many others. Also, houses of the P-44T series in many areas were built pointwise.

In the Moscow region, new buildings of the P-44T series have been built / are being built in the cities of Balashikha, Zheleznodorozhny, Lobnya, Krasnogorsk, Lyubertsy, Moskovsky, Kotelniki, Reutov, Odintsovo, Khimki, Shcherbinka, as well as in the village. Bear Lakes, pos. Blue, der. Brekhovo, der. Pykhtino.

The number of houses built in Moscow: about 600, in the Moscow region - about 200. In the market of new buildings in Moscow and the Moscow region, this series is one of the most common. At the same time, the share of social homes is about 50%.

Normative life of the house(according to the manufacturer - DSK-1) - 100 years

Areas of 1-room apartments (4 standard sizes): total: 37-39 sq. m., residential: 19 sq. m., kitchen: 7-8.4 sq. m.

Areas of 2-room apartments (4 standard sizes): total: 51-61 sq. m., residential: 30-34 sq. m., kitchen: 8.3-13.2 sq. m.

Areas of 3-room apartments (6 standard sizes): total: 70-84 sq. m., residential: 44-54 sq. m., kitchen: 10-13 sq. m.

All rooms in the apartments of houses of the P-44T series are isolated

bathrooms: in 1-room apartments - combined, in 2- and 3-room apartments - separate, baths: standard, 170 cm long.

Stairs: smoke-free. Garbage chute: with a loading valve on each floor

Cooker type: electric

Walls: external reinforced concrete three-layer panels (concrete - polystyrene insulation - concrete) with a total thickness of 30 cm (the thermal insulation of which is equal to a brick wall 90 cm thick.) Interroom and interior load-bearing panels - reinforced concrete panels 16 and 18 cm thick. ("per room") reinforced concrete slabs 14 cm thick.

Bearing walls: longitudinal inter-apartment and transverse all (inter-apartment and inter-room)

Section type: end, in-line and rotary (angular). The entrance, where the electrical panel is located, has an entrance from 2 sides

Number of steps in the section (entrance): 7, step width (distance between two adjacent load-bearing walls): 300 cm (in 3 central bays of each section), 360 cm (in the rest)

Cladding, plastering of external walls: brick-like cladding, lower floors - stone-like cladding

Color options for external walls: dark orange, light red, lower floors - gray, bay windows and half-windows - white

Roof type: flat-pitched or pitched tiled by BRAAS DSK-1, colors: green, brown

Distinctive features: the P-44T series of houses differs from its predecessor - the P-44 series (which was built in 1979-1999) by increased thermal insulation of the walls, a ventilation duct in the hallway (and not in the kitchen), glazing of loggias, bay windows and half-windows, as well as a recognizable exterior finish under the brick

Other advantages: increased sound insulation, heaters with temperature controllers, copper wiring, "closed joint (seam)" technology, world standards for solidity and fire resistance (1st class), modern security system (response to opening doors of the basement, switchboard, attic, elevator shaft flood and fire warning system). Rapid pace of construction (1 floor in 3 days): www .1 Dom specialists. ru did not reveal a single case of long-term construction of houses in this series.

Flaws: quality of installation of external walls in separate buildings

Manufacturer: DSK-1 (the largest enterprise in the construction industry in Russia)

Designer: MNIITEP (Moscow Research Institute of Typology and Experimental Design)

Structural characteristics and appearance of houses of the P-44T type series in many respects similar to the houses of the P-44M series,

The first house of the P-44T series was built in 1997 on the street. Marshal Vasilevsky (Shchukino). One of the most recognizable in Moscow, a multi-storey stepped residential complex with spiers on Rubtsovskaya Embankment, resembling a castle in shape, was built from block sections of the P-44T series

It has been under construction since 1997. and to the present. It has its own modification, which differs from it only in the number of floors - this is the P-44T / 17 series.

House P-44T panel, consists of corner and ordinary sections of four apartments, where a 1-room apartment has a living space size - 19m 2, a kitchen - 7-9m 2, bathrooms are combined; 2-room apartment - 30-34 m 2 , kitchen - 8-13 m 2 , separate bathrooms; 3-room apartment - 44-54 m2, kitchen - 10-13m2, bathroom is also separate. All rooms in the apartments of houses of the P-44T series are isolated. All apartments have bay windows and spacious balconies. Internal walls are made of prefabricated reinforced concrete panels 16 cm and 18 cm thick. Exterior wall three-layer hinged panels with EPS insulation and heat-reflecting metallized film inside the insulation, total thickness 30 cm; from the front side they are faced with brick-like tiles, starting from the second floor. Partitions made of many materials: tongue-and-groove or foam concrete blocks, gypsum boards on a metal frame, gypsum concrete rolled panels, but most often gypsum concrete, they are all of the same thickness - 8 cm. Ceilings - reinforced concrete slabs 14 cm thick.

A series of residential buildings P-44T has various disadvantages, such as a narrow room in two-room linear apartments (with windows on one side), the seams between the panels require additional lubrication (otherwise it will be cold). The possibilities of redevelopment in a house of this type are very seriously limited. Almost all walls are load bearing. However, the following possibilities remain for acceptable redevelopment without detrimental effect on supporting structures:

• In three-room apartments, the partition between the large room and the corridor is non-bearing.
• The sanitary unit is made of gypsum and can be dismantled and/or modified.
• In houses built after 2007, in the load-bearing panels between the kitchen and the room, in some apartments there is a special niche for making a doorway (“wafer”), which can be dismantled.

Nevertheless, this series also has a number of advantages: bay windows, copper wiring, natural exhaust ventilation, hot water supply with top spill were added to the layouts, the appearance acquired a special color - red with sand, bay windows and loggias were painted white. For living in houses of the P-44T series, it happens that the attic floor is available. A modern security system has appeared that reacts to the opening of office premises, flooding or the threat of a fire.

Each entrance has one passenger and one cargo-passenger elevator, in 20-25-storey sections (entrances) - 2 cargo-passenger and passenger. The number of entrances is from 1 to 8. The stairs are smoke-free, there is no fire balcony. The garbage chute is located on the stairs, with a loading valve on the platform.

The service life of the house of the P-44T series is about 100 years, so you should not hope for demolition in the near future.

Let's visit today a 3-room apartment, a panel house of the P-44T series from the developer DSK-1
The apartment turned out to be good and spacious, but the designers didn't get smart with the design and the layout turned out to be similar to other similar three-room flats in panel houses. The rooms are all isolated from each other. A large bay window was added to the kitchen and a triangular bay window is present in the room of the corner apartments. Two rooms have balconies.

We will consider the layout of a three-room apartment with the following dimensions:

Room with a balcony boot 17.8 sq.m. (on the diagram number 1)

Room without balcony 14.1 sq.m. (on the diagram number 2)

Room with balcony iron 11 sq.m. (on the diagram number 3)

Kitchen with a large bay window 12.9 sq.m. (on the diagram number 4)

Corridor with entrance hall 14.6 sq.m. (on the diagram number 7)

Living area 42.9 sq.m

The total footage of the apartment without balconies is 70.4 sq.m.

layout plan of a three-room apartment P-44T with dimensions

We open the front door and get into the dressing room. Ahead is a wall with an opening, in which a small arch was originally made. To the right of the door, there is a small space that can fit a small dressing room or shoe cabinet.

In this version, we see an example of such a cabinet for shoes.

This place can also be occupied by a beautiful large full-length mirror.

We pass forward and get into the very center of the hallway. Three doors meet us. On the left, a large double door leads to a room of 11 sq.m. and a slipper balcony. And two adjacent doors are rooms. To the right, the largest room is 17.8 sq.m. with a booty balcony, and that on the left is a small room of 14 sq.m. no balcony.

Some interesting ideas in the design of the hallway of a three-room apartment. The photo shows that compartment doors were installed in the room closest to us on the left.

Another interesting entryway. Lighting was installed in the arch.

And here, on the right side of the blue hallway, columns with lighting were used in the design.

Arrangement of furniture in the hallway

If you need more space in the rooms and do not litter the rooms with cabinets, the hallway is suitable for these purposes.

A large wardrobe will be installed along the long wall.

Who has not completely gone into e-books, but collects a home library at home, an interesting solution would be if you place shelves for books in the hallway.

Corner shelves will fit in the corner.

Room with balcony

From the hallway we go into a room with a large doorway. Usually this room is used as a living room or hall. The room, although not very large, is square.

And if you remove the window frames and dismantle part of the window sill, you can extend the room and connect it together with a balcony.

Three rooms are not always enough for tenants. Often on the balconies they organize workrooms. It turns out that they are in a situation where every square meter is expensive.

Let's turn our backs to the balcony and observe two interior doors, in the standard layout of the final renovation from the developer DSK-1

You can beat the doorway a little. Build a small arch and change ordinary doors to sliding ones.

Two doors eat up a lot of space. And if you make a single-door opening, you can put a corner cabinet in the corner of the room.

And sometimes they completely dismantle the entire wall. And it turns out that instead of a room, a spacious hall is connected into one whole with a hallway.

Large room with balcony

Standard large room with its own balcony. The size of the long wall is 5.56 sq.m and the short one is 3.22 sq.m. It can be designed for both parents and children's room.

If the balcony is insulated, the walls can be covered with wallpaper. Bring outlets to the balcony and hang lamps for lighting.

Walls that we remember from Soviet times are becoming less and less popular. Instead of them, long chests of drawers often appear in the designs and interiors of the apartment.

But flowers, as they were in fashion, still adorn our apartments.

Room without balcony

In the third room, there is no balcony. Large and wide window. The size of one wall is 4.34 sq.m. and along the wall with a window of 3.22 sq.m.

Nice place for a bedroom. Thick dark curtains will help isolate yourself from the morning sun and sleep on a soft bed on a day off.

Large paintings on the wall look original above the bed.

The closet will not be an extra item in the room.

Bath and toilet in a 3-room apartment

We leave the room and go to the kitchen. On the way down the hallway, we see the doors to the bathroom and toilet, and on the right of the hallway there is an empty, but very convenient space for a closet.

Wall material: panel with "brick" cladding
Number of sections (entrances): from 1. Sometimes several entrances in one building are block sections of the P-44T series, while others (central and / or corner) are from block sections of other series: P-44K, P-44TM / 25 (TM-25)
Number of floors: 9-25, the most common options are 14, 17. The first floor is most often residential
Ceiling height: 2.70 m.
Elevators: passenger 400 kg and cargo-passenger 630 kg, in 20-25-storey sections (entrances) - 2 cargo-passenger and passenger (the modification was called P-44T/25)
Balconies: in all apartments, starting from the 2nd - 3rd floor, glazed loggias, in 2- and 3-room apartments there are also bay windows and half-windows
Number of apartments per floor: 4
Years of construction: from 1997 to the present. time

Panel houses of the P-44T type series in Moscow were built as in new areas of mass development: Maryinsky Park, Lyublino, Northern and Southern Butovo, Mitino, Novokosino, Novoe Kozhukhovo, Zhulebino, Nekrasovka, pos. Severny, Khodynka, and in the old areas where mass demolition of five-story buildings and dilapidated buildings was and is being carried out: Khovrino, Koptevo, Beskudnikovo, Degunino, Sviblovo, Medvedkovo, Yurlovo, Alekseevo, Izmailovo, Lefortovo, Perovo, Nagatino, South Chertanovo, Zyuzino , Cheryomushki, Solntsevo, Ochakovo, Kuntsevo, Fili, Shchukino, Zelenograd, st. 1905, st. Borisovskiye Prudy, Nizhegorodskaya st. Also in a number of other districts (including in the Central Administrative District), houses of the P-44 series were built pointwise
In the Moscow region, new buildings of the P-44T series have been built and are being built in the cities of Zheleznodorozhny, Balashikha (microdistrict 1 May, microdistrict 22 Balashikha-Park, etc.), Lobnya, Krasnogorsk, Lyubertsy, Moskovsky, Kotelniki, Reutov (including part microdistrict Novokosino-2), Odintsovo (including Nemchinovka), Khimki, Shcherbinka, as well as in the village. Bear Lakes (Schelkovsky district), pos. Blue and der. Brekhovo (Solnechnogorsk district), village. Pykhtino and residential complex "Butovo-Park" (Leninsky district)
The number of buildings built in Moscow: about 600, in the Moscow region - about 200 (including those under construction). The P-44T series is the most common in Moscow among all modern standard series of houses. The number of municipal houses built for migrants from the demolished fund, for young families, etc. - about 50%
The normative life of the house (according to the manufacturer) is 100 years

Areas of 1-room apartments: total: 37-40 sq. m., residential: 19 sq. m., kitchen: 7.4-8.4 sq. m. (in the 25-storey modification - 9 sq. m.)
Areas of 2-room apartments: total: 52-64 sq. m., residential: 32-34 sq. m., kitchen: 8.3-13.2 sq. m. (in the 25-storey modification - 12.8-13.8 sq. m.)
Areas of 3-room apartments: total: 70-84 sq. m., residential: 44-54 sq. m., kitchen: 10-13.2 sq. m.
All rooms in the apartments of houses of the P-44T series are isolated
Bathrooms: in 1-room apartments - combined, in 2- and 3-room apartments - separate, baths: standard, 170 cm long.
Stairs: smoke-free, in 20-25-storey sections (P-44T/25) are equipped with common balconies. Garbage chute: with a loading valve on each floor
Cooker type: electric. Ventilation: natural exhaust, ventilation units in the bathroom and in the hallway
Walls: external reinforced concrete three-layer panels (concrete - polystyrene insulation - concrete) with a total thickness of 30 cm (the thermal insulation of which, according to the manufacturer, is equivalent to a brick wall 90 cm thick.) Inter-apartment and interior load-bearing panels - reinforced concrete panels 16 and 18 cm thick. 8 cm thick. Ceilings - large-sized ("per room") reinforced concrete slabs 14 cm thick.
Bearing walls: longitudinal inter-apartment (as well as inter-room in the end apartments - "vest") and transverse all (inter-apartment, inter-room and inter-balcony)
Type of sections: end, in-line (ordinary, P-44-1) and rotary (angular). The entrance, where the electrical panel is located, has an entrance from 2 sides
Number of steps in the section (entrance): 7, step width (distance between two adjacent load-bearing walls): 300 cm (in 3 central spans of each section), 360 cm (in the rest)
Color options for external walls: dark orange, light red, sand, lower floors - gray with a stone finish, bay windows and half bay windows - white
Roof type: flat pitched with BRAAS DSK1 tiles. Technical floor: above the upper residential floor

Distinctive features: the P-44T series of houses differs from its predecessor - the P-44 series (which was built in 1979-2000) by increased thermal insulation of the walls, increased kitchen areas due to the removal of the ventilation duct into the corridor, bay windows, as well as a recognizable brick-like exterior finish
Other advantages: heaters with temperature controllers, copper wiring, hot water supply with top spill, world standards for solidity and fire resistance (1st class), fast pace of construction (1 floor in 3 days): www.site experts did not identify a single cases of long-term construction of houses of this series
Disadvantages: the quality of the installation of individual elements of the outer walls in some buildings, a narrow smaller room in 2-room apartments - "rulers" (with windows on one side)
Manufacturer: Moscow House-Building Plant No. 1 (DSK-1)
Designer: MNIITEP (Moscow Research and Design Institute for Typology and Experimental Design)
The design characteristics and appearance of the houses of the P-44T type series are in many respects similar to the houses of the P-44TM, P-44K series
Apartments in new buildings of the P-44T series can also be purchased with a municipal finish

The first house of the P-44T series was built in 1997 on the street. Marshal Vasilevsky (Shchukino). One of the most recognizable in Moscow multi-storey residential complex with spiers on the Rubtsovskaya Yauza Embankment (project I-1774) was built from block sections of the P-44T and P-44M series
In 2005, on the basis of the P-44T type series, a project of typical block sections of the P-44K series was developed, where in each section there are 1 step less - 6 steps (“6-module”), and, accordingly, only 1- and 2-room apartments. Currently, this series is being built more actively within the Moscow Ring Road
A 5-module was also developed (a 5-step version of the P-44T), where 1-room apartments are completely so-called studios with a total area of ​​23-28 square meters. m. The 5-module has not yet gone into mass production (www.site experts have adopted the code name P-44-5M for it)
Site rating of the P-44T type series: 8.2 (on a 10-point scale)
Photo: www..dsk1.ru, www.morton.ru