The indoor fountain will decorate the house, humidify the air in the room, and give a little coolness on a hot day. It is not necessary to buy expensive equipment. If you consider yourself a creative person, then be patient, let your imagination run wild and start creating a fountain with your own hands.
The design of the indoor mini fountain is quite simple. It is based on the principle of a closed cycle: water is poured into a system connected to a power source, while a submersible electric pump lifts the water up, and then, depending on the type of construction, it flows into a storage tank.
The indoor fountain can be of three types, depending on the method of water discharge:
- gushing: the jet beats up and falls into the mini-pool;
- cascading: water falls from a small height, overflowing over decorative ledges;
- closed: water circulates in flasks or flat wall-mounted containers in the form of pictures.
Photo source: http://svoimirykami.ucoz.ru
The location of the indoor fountain
Before starting work, decide on the size and location of the future fountain. A bulky, large fountain will look out of place in a small apartment.
The indoor fountain can be floor, wall or tabletop. The choice depends on the size of the room and on the functions assigned to the fountain. For a small room, a small tabletop fountain would be optimal.
Functionally, the fountain serves not only as a decor item, it moisturizes the air well. Therefore, fountains should not be installed near wooden furniture: it can deteriorate from constant moisture. When choosing the location of the fountain, also consider the presence of small children or pets in the house: install the structure where it will not interfere with anyone.
Photo source: http://www.coonplace.ru/
Fountain materials
Most often, indoor fountains are made of glass and stone. The glass part is a kind of foundation for the fountain, its foundation. Stones are used for the stability of the structure. For parts of the fountain that do not come into contact with water, you can use wood, ceramics, synthetic materials.
Photo source: http://www.zoloto72.ru
The indoor fountain can be supplemented with lighting. At night, such a fountain will serve as a kind of night light. Sound background and additionally built-in clock or barometer will make the fountain functional.
The main element for creating an indoor fountain is a pump (water pump) for water circulation. The indoor fountain is a small installation, so don't overdo it. Choose low power silent pumps for aquariums or especially for small fountains with a power of approximately 6 W and 240 liters per hour. The higher the power, the noisier the pump. You should hear the murmur of water, not the operation of an electric motor.
Photo source: http://svet-lanka.blogspot.ru
Indoor Fountain Decor
The beauty of creating a fountain with your own hands lies not only in saving money, but also in the ability to decorate it to your own taste. If there are difficulties with inspiration, then you can always take advice from people who know: look through magazines about the interior.
What can be suitable as a decor? Before you run to the store, think about how many cute little things you have at home idle. A cache-pot, a ceramic pot or a vase, shells brought from the sea and pebbles, the most popular “filling” for fountains, can be used as a base. Even souvenir figurines can find a second life. Artificial trees and flowers, gravel, live plants - all this can become a decor for a fountain.
To create flowing water, you can use different containers: bowls, sea shells, lakes, etc.
Photo source: http://domgvozdem.ru/
indoor fountain step by step
Making a fountain with your own hands is very simple. The main thing you will need:
- hermetic container for a fountain: a flower pot, a vase, a pot, a bucket;
- water pump (water pump). A pump can be bought at a hardware store or pet store, a low-power water pump for aquariums will do;
- a piece of hose (for example, for cleaning aquariums);
- decor elements.
Photo source: http://www.trozo.ru
We install the pump at the bottom of the selected vessel (there are suction cups on the pump) and attach a hose to it. We cover the pump with stones, and the water supply tube is brought up between them. We cover the space around the pump with large decorative elements (expanded clay, stone), then with smaller ones (pebbles, shells, glass). We leave only the outlet of the filter, - fill the rest with water. The tube, like the pump itself, should be completely masked so as not to disturb the harmony of the composition. And then decor and decoration at your discretion.
Photo source: http://home-sweet.ru
A good solution is to “seat” a figurine (often frogs are used) on a tube that supplies water. To do this, you need to drill a hole in the figurine and thread a tube into it, water will flow from the frog's mouth.
Reliable fixation and sealing of the entire structure is achieved through the use of waterproof adhesives.
The power of the ejection of water is regulated by a wheel, which is located on the pump housing. This power also depends on the diameter of the tube: the smaller it is, the higher the jet, respectively. If you want the water to flow out in several streams, install a divider on the tube.
The operation of an indoor fountain does not cause much effort and consists only in maintaining the water level in sufficient volume for circulation. There should be enough water so that the pump is constantly in the water. The water will evaporate, so every week it will have to be added to the fountain.
Photo source: http://tvoidizain.ru/
funny video
2 year old loves to throw. Look what happened when his parents bought him a basketball hoop!
Fountains are not only coolness on a sunny day. This is the positive energy that spills over the house from the sounds of babbling water.
Many people want to surround themselves with artificial ponds or at least small fountains in order to relax and unwind after work near them. All this can be done by yourself: it is enough to learn how to make a homemade fountain with your own hands and build it, and quite quickly and efficiently. And just such a fountain, created by yourself, will become an exclusive decoration of your site and home!
Varieties of fountains
All fountains can be conditionally divided into fountains designed for indoors or outdoors. The first type includes indoor fountains. They are used more for the purpose of decorating the interior of the house and can be different in shape and size, depending on the parameters of the room.
Outdoor fountains are designed to decorate the backyard. They are located on the site in front of the house or in the garden. They can be made of plastic, natural stone, marble, porcelain.
In addition, such a fountain can be equipped with lighting, and then you can admire it not only during the day, but also in the evening and at night. The atmosphere of a holiday with such a fountain is provided!
country fountain
Many people ask themselves the question - how to make a fountain in the country? Before you start arranging this hydraulic structure, you need to decide on the desired model. Its appearance directly depends on the general style of the site. So, if a cottage in a rustic style, a mill-shaped fountain is perfect, and for a classic-style site, it is better to build a fountain with a minimum of decor or in the form of a statue.
If your dacha resembles a picturesque corner of nature, you can make a small fountain that resembles a geyser, beating right from under the stone. You can also place a fountain near an artificial reservoir surrounded by boulders.
Many lovers of country life torment themselves with the question of how to make a simple fountain in their area. To do this, the fountain pool is buried in the ground, and a special recess is made at the base for all the equipment and the pump.
The main advantages of such a fountain are its elegant design, shallow depth and a convenient built-in overflow-drain system. However, there are also disadvantages - high costs when installing the pool itself, cable and fittings. If you decide to make a fountain at home and settled on this particular type, arrange it so that each element pleases the eye and creates a feeling of harmony and peace.
Tools and materials for arranging a fountain
Before proceeding with the installation of the fountain, you need to acquire materials: a beautiful fountain is unlikely to come out of nothing. The choice of materials for the fountain depends on the place from which its arrangement begins. It is better to use a small reservoir in the summer cottage for the construction of the fountain, and then before you make a home fountain, you will not need to think about the flow of water. If there is already a reservoir, then for work you will need:
- storage tank;
- set of nozzles;
- the fountain itself;
- pump.
The most crucial moment is the choice of the pump. The modern market offers electromagnetic, centrifugal and vortex pumps. For country fountains, it is recommended to use centrifugal pumps, as they are more powerful, but at the same time quite economical. If there is no reservoir on the site, you need to dig a pit and equip an artificial pond in it, equipping it with a special film and a concrete block on which the pump will be placed.
Stages of building a fountain
The organization of a country fountain needs careful planning. In order to understand how to make a fountain with your own hands, you need to correctly calculate the location of the future structure, its proximity to power supplies and water supply.
Water from the fountain can be drained into the sewer, or it can be recycled - reused, which significantly saves the process. When preparing sewer channels for draining water from a fountain, a storm water inlet will probably be used.
If there is a ready-made bowl for the fountain, a foundation pit is dug out for it. Otherwise, they also dig recesses and equip it like a small pool: drainage in the form of sand, strengthening walls, a waterproofing layer, connecting a sewer drain.
The device of the fountain itself begins with the installation of the pump. It is important to remember that there is a submerged and a surfaced position for fountain pumps, with a surface pump more commonly used for large fountains as it produces a higher and stronger jet. It is also necessary to take care of good electrical insulation. The fountain itself, as a rule, is installed in the center of the pond so that water does not spill over its borders.
Fountain decoration
The uniqueness of a homemade fountain can be emphasized by decorating it. How to make a fountain at home so that it becomes a decoration of the yard both day and night? This is possible due to the effect of artificial illumination of the fountain with the help of special lighting equipment. Lamps that illuminate the fountain around the perimeter and even in the water will help create a fabulous harmony of water and light.
You can also plant bushes or flowers around the fountain, and green the bottom of the reservoir itself with the help of various aquatic plants. The fountain can be decorated with wood, stone or statues.
When equipping the fountain, you can use ready-made statues and figures. But it depends on you how exclusive the standard fountain will become.
indoor fountain
Any interior of the apartment can be revived with the help of a small fountain. Before starting work, it is better to figure out how to make an indoor fountain with your own hands and think through all the nuances. To implement this idea, you will need the following materials:
- the container on which the fountain will be located;
- aquarium pump;
- a small piece of hose for cleaning the aquarium;
- glue;
- large sink;
- colored decorative soil, shells and expanded clay.
First you need to find a container in which the fountain will be located. For this purpose, you can use any vessel you like, for example, flower pots. You can also choose a beautiful flower pot or basin for the fountain, as long as the water does not leak out.
In addition, you need a pump with a sprinkler and no tip, since the container for the fountain will be small. The main task of the pump is to raise the stream of water.
Stages of construction of a decorative fountain:
- Cut off a small piece of about ten centimeters from the aquarium hose. You need to immediately put it on the pump tip and make sure that all the holes in it are open at full strength, since the power of the jet depends on this. Then you should strengthen the pump at the bottom of the selected container.
- We fill the pump with expanded clay and level its surface.
- Cover the expanded clay with plastic wrap with a hole for the hose.
- We pour decorative primer on the surface of the film.
- If you need a stone sink stand, then it should be glued with epoxy waterproof glue to the sink.
- Install the stand by first stretching the hose into it.
- We put on the sink through the drilled hole at the end of the hose and pull the hose into it one centimeter.
- Decorate the surface of the fountain with beautiful shells or stones. And the sink from which water flows can be replaced with something else, as long as there is a hole for the hose. The design and style of an indoor fountain completely depends on the imagination of the master who makes it.
Decorative mini fountain
A cool fountain on a hot summer day improves mood and invigorates. In such a situation, even a small fountain will be just a salvation for you. How to make a mini fountain? It's pretty easy, you just need to stock up on the following materials:
- flower pot with tray;
- small water pump
- paints for ceramics and glass;
- contours;
- ornamental plants for the aquarium;
- artificial translucent balls or stones.
Stages of work:
- The flower pot will serve as the base for the fountain. If desired, you can decorate it with an unusual painting. To do this, use special paints for ceramics and glass.
- Then install the pump under the pan, for water circulation, you need to make a small hole in the bottom for drainage.
- Pass the pump tube through the hole, and fill the bottom with decorative pebbles.
- Assemble the entire structure and fill it with water. Ornamental aquarium plants will help to revive the landscape.
Thanks to this scheme, everyone can make a mini fountain with their own hands, connecting their imagination and imagination.
Fountain lighting
One way to make even an ordinary fountain magical is to use lighting. It could be:
- surface lighting in the form of lanterns around the perimeter of the fountain;
- underwater lighting with waterproof lamps;
- floating backlight on built-in autonomous batteries.
With underwater illumination, the effect of the glow of water is created, if the illumination is rotating, then the whole process turns into a water-light extravaganza. For this, a rotary mechanism is used.
An important step in lighting equipment is laying wiring in a water-repellent tire. For safety, it is equipped with an automatic breaker (in case of current leakage). To comply with safety regulations, when installing fountain lighting, lamps with a voltage of 12 volts are used. These are, first of all, halogens, and lamps on optical fibers and LEDs. Connect the lamps to the network or transformer.
If you want to illuminate the water surface, place lamps around the perimeter above the water. If you want to emphasize some element of the composition, use a directional beam of light, if the whole composition is a spotlight. Using spotlights, you can focus on one detail, for example, a group of plants in a pond.
Fountains have always adorned any interior. Today they are widely used for the purpose of decorating premises, and ennoble personal plots. Therefore, they are widely used in landscape design. A fountain on the lawn, near the gazebo, near an artificial reservoir surrounded by rockeries - there are many options for the location of fountains. They can occupy any free space or become a central place in the design of a garden plot. By letting your creativity run wild, you can figure out how to make the fountain not only beautiful, but also unusual.
How nice after a hard day's work to relax by the cool, soothing murmur of water fountain made by one's own hands. Even a small decorative fountain in a summer cottage will become not only a bright decoration of the landscape, but also a favorite place to relax, where you can enjoy unity with nature. It will not be difficult to give yourself this incomparable pleasure if you realize the idea yourself, knowing how to make a fountain in the country with your own hands.
Choosing the right place
Garden fountains are the best way to solve the problem of air humidification during the hot summer months. Regardless of the style in which the hydraulic installation is made, be it classic, rustic, oriental, avant-garde, it will be a bright touch in landscape design. Fascinating overflows of water streams, playing in the sun with all the colors of the rainbow, will not leave anyone indifferent.
The key to a successful choice of a place for a fountain is proportionality with the appearance of the site and the overall harmony of the garden.
When choosing a location, it is important to consider the possibility of connecting to the power supply for the uninterrupted operation of the pump.
When deciding on the location of the fountain, one should start from the presence and degree of slope of the earth. It is better if the installation is placed in a lowland, which will increase the saturation of the air with moisture, as well as adjust the volume of groundwater.
It is undesirable to place fountains:
- in too open places of the site, since direct sunlight will provoke the "bloom" of water;
- near trees, since powerful roots can deform the fountain bowl and damage the waterproofing, and foliage from trees, fruits, seeds and fluff, falling into the reservoir, can cause malfunctions;
- in the immediate vicinity of the house so that the wind currents do not bring moisture to the walls of the building.
The most successful place is a platform that is well visible from the house and various parts of the garden.
Preparing a suitable container
When deciding to create a fountain with your own hands in the garden, it is important to correctly choose or make your own container for a hydraulic installation.
As a fountain bowl, you can use ready-made plastic containers of various shapes that allow you to provide reliable waterproofing.
To create larger fountains, it is required to dig a foundation pit, at the bottom of which a foundation for the future structure will be equipped. The bottom of the dug hole under the fountain is covered with a layer of sand, the side walls are reinforced with bricks. After that, the inner surface of the tank can be covered with a plastic film that does not allow water to pass through. Surface seams can be sealed by treating them with frost-resistant silicone.
An important point: the level of penetration of the base should be below the level of the soil. This placement will eliminate the possibility of washing away the soil around the bowl of the fountain.
An emergency drain can be provided near the edge of the surface, the presence of which will not allow water to rise above the required level.
Craftsmen, creating a fountain with their own hands in the country, use any waste materials: natural stones, river pebbles, car tires, glass products, ceramic parts
The main requirement for the material is high strength characteristics and the ability to withstand temperature extremes.
The finished bowl can be filled with water.
Pumping system installation
It is impossible to put a fountain into operation for a summer residence without connecting its “heart” - a powerful pump that ensures the continuous movement of a powerful stream. The success of the long-term operation of the fountain directly depends on the correctness. The general principle of operation of the system is quite simple: the water ejected through the nozzle is collected in a bowl. From the bowl, it flows into the drain hole, from where it enters the pipeline and, as it moves, it first undergoes a coarse, and later a finer cleaning. The pump from the pipeline pumps already purified water to the nozzle.
When thinking about the question of how to make a fountain in the country, it is imperative to provide for the installation of a drainage system. The pipeline for the system can be equipped with plastic pipes with a diameter of about 16mm. Plastic has excellent performance and long service life. The plastic construction is easily connected with a special soldering iron.
Decorative garden fountains are mainly equipped with circulation pumps, in which water is taken from the bowl, passing the circle, is discharged back into the fountain
The power of the pump directly depends on the capacity of the bowl of the fountain, as well as the expected power of the jet, which will break out of the water like bright fireworks.
You can supplement the water circulation system of the fountain by installing a receiver - a pressure tank. Installing a receiver allows you to provide a constant pressure for water to enter the nozzle and stable operation of the system as a whole. With this configuration, water is pumped into the receiver by a pump, and then transferred to a nozzle located at a lower level.
The action of cascading fountains is based on the same principle.
The water in the cascade flows smoothly in a small waterfall along several steps located at different levels.
After installation, the pump should be checked for operability and only then decorated with decorative elements.
Optional equipment
Installing additional equipment for the fountain will transform and diversify the design.
Special nozzles allow you to give jets of ejected water the most unusual shapes: geysers, tulips, domes, umbrellas, hemispheres
The combination of nozzles and the effect of the shapes they form allows you to create whimsical water patterns.
Additional lighting miraculously transforms the fountain for giving, giving it a magical effect. Since light sources often come into contact with water and are located directly in the body of the fountain, increased requirements should be imposed on their choice: contacts protected from water, hermetic design.
Decorative lighting, disguised in the bottom of the reservoir, will delight the eye in the coming twilight with the effect of water glow
Underwater lighting devices, as well as all kinds of floating lamps, are very popular for decorating fountains.
An interesting decor option is a small water mill. Making Instructions:
Proper care of the fountain will help extend the life of the hydraulic installation: it is advisable to dismantle the removable structural elements for the winter period. With the onset of cold weather, the tank itself should be emptied of water and securely covered with a film that protects against dust, dirt and precipitation.
For any owner, the appearance of a summer cottage or yard is of great importance. Its design can be done by specialists, but, if desired, you can do it yourself. A fountain will be a good decoration of the yard or plot. It can also be built according to your own project.
Types of fountains
Fountains for giving are of different types. They are divided into types: by device, by appearance, by features of work, etc. According to the method of device, country fountains are circulation and flow, they are also called "Roman".
Did you know? The first fountains appeared in ancient Greece and in ancient Rome.
Circulating suggest the water cycle. Water fills a certain reservoir (bowl, vase, reservoir) and with the help of a pump is supplied to the device, from which a stream of water directly shoots.
Everything is arranged so that the outgoing water enters the tank and swings up again. Thus, the device does not involve the supply of water from a water supply system or a well. The only thing that is needed is to add water to a certain mark, because it tends to evaporate or splash.
flow fountains arranged with the involvement of water supply (wells) and sewerage. Water flows up, falls down and goes into the sewer. The method is, of course, irrational, but such fountains have a number of advantages:
- aesthetic appearance;
- drinking water;
- the possibility of using water for watering lawns, flower beds, shrubs and trees.
Did you know? The tallest fountain in the world- 312 m. It is called the fountain« Fahda» is located in Saudi Arabia.
Choosing the right place
If you decide to build a fountain on the site with your own hands, then, first of all, choose a suitable place for this. If there is a cottage or a pond, the choice of location is obvious. Where the pond is located, there will be a fountain. The device of the pond, of course, will have to be modified, corrected, but the foundation will remain.
If you are starting from scratch, then you need to choose a place, carefully weighing all the pros and cons. DIY garden fountains perform different functions: they humidify the air in the garden, which is good for trees, create cool conditions, can be used for irrigation, etc.
For this reason, you need to choose a place so that the fountain not only brings aesthetic pleasure, but is also useful. A suitable place for arrangement would be an open area between trees, shrubs or hedges.
Trees and bushes should not hang over a pond or reservoir so that debris does not fall into the water and leaves fall. This is bad for water filters. Also, due to the proximity of trees, and hence their root system, a violation or even destruction of the underground part of the fountain is possible. If plants grow in the country that cannot tolerate waterlogging, equip the fountain away from them.
Important! Do not place the fountain near buildings.
There is no need to equip the structure in the open sun, because this is fraught with flowering water. There is one more condition: a do-it-yourself fountain in the country should be in harmony with the overall design. Everything should be done in the same style. This should be a platform that is clearly visible from the windows of the house and from any part of the yard, because you are building a fountain, first of all, for aesthetic pleasure.
Preparation of materials for construction
When the place for the fountain and its type are chosen, the project is developed, it is necessary to determine what materials for construction will be needed. Let's assume that the project is designed for a circulating jet static fountain with a single ejection of water, i.e. of the "Geyser" type.
At home, to equip a fountain with your own hands, you will need cement, sand, gravel, a durable plastic film and a building facade mesh sized according to the diameter of the structure (both the film and the mesh must be the same size). In addition, you need a plastic container with a volume of about 50-70 liters, depending on the size of the structure.
If you plan to decorate everything with stones, then prepare them immediately. It can be a wild stone of the right size, cobblestone, granite, large pebbles, etc. A fountain pump will be needed to ensure proper operation.
Pump Selection Criteria
Depending on the type of fountain, you need to choose a pump. For the "waterfall" we would choose a surface pump, and since we have a traditional fountain, we choose a submersible one.
As a rule, submersible pumps perform their function perfectly. They are compact, quiet, easy to install and, most importantly, affordable. Submersible pumps come in different capacities. It is calculated in the amount of pumped water per hour (l/h). 
The height of the jet will just depend on the power of the pump. The maximum height is calculated by the diameter of the "foot" you made. The pump in this case does not need to be chosen according to the principle "the more powerful, the better." For the arrangement, we need such that the jet is high enough, and that the spray does not fly out beyond the "foot". For summer cottages, the height of the jet is suitable from 80 cm to 1 m.
Important! Care must be taken to ensure that water does not splash outside the fountain. Excessive moisture can lead to the death of plants and damage to things.
Manufacturers, as a rule, provide a table of the ratio of power and jet height in the instructions. Since we are equipping the Geyser, such a device will need a pump with a capacity of about 7000 l / h.
The principle of installation of the pumping system
The pumping system is installed 10 cm above the bottom on a stand (lined brick or mounting pedestal). A hose or pipe with water supply is supplied to it. Usually a sprinkler comes with a pump, but if it is not there, then you can make it yourself.
To do this, you can take a regular pipe made of stainless steel. The diameter will depend on the height of the jet and the diameter of the water spray. For a small fountain of 0.8-1.0 m, a diameter of 2-2.5 inches will suffice. The length will depend on how deep the pump is submerged. It is enough to leave 10-15 cm above the water. 
To shape the jet, you can flatten the pipe, roll it, leaving a hole, drill a few holes, or cut a thread and screw on the desired nozzle. Connect to the pump directly or through an adapter (if necessary).
Fountain installation. Step-by-step instruction
A do-it-yourself master class for installing a fountain in a country house with a step-by-step photo is easy to find on the Internet. Usually the installation takes place in several stages. Arrangement for the selected project includes 10 steps:
Important! Be sure to follow safety precautions when performing any work on installing the fountain.
Don't let the initial costs scare you. I have found from personal experience that ABSOLUTELY ALL ways of home business without initial costs do not bring the desired income and satisfaction from the (sometimes just HUGE) work done. Therefore, I suggest you do a very interesting job. The essence of the idea is simple: the production of decorative indoor fountains. At low cost, amazing results are obtained.
The system of any decorative indoor fountain is a cycle in which water rises up with the help of a pump and then flows down the stone into a container. Thus, we are talking about a closed system in which the used water is gradually renewed, since the initial supply of water is no longer enough by a certain time.
The pump is usually powered by a set of batteries or a power supply or both. Usually, for decorative indoor fountains, pumps powered by 3 to 9 volts are used. The higher the power, the greater the power of the pump, which allows you to lift more water up, and this, in turn, affects the location of the pipes through which the water flows. You can make a very tricky labyrinth of tubes, from which water will flow out in different directions and with different strengths and, believe me, it looks very, very beautiful!
Now let's talk about the design
The basis of any decorative room fountain can be any. While shopping, pay attention to all kinds of bowls with lids. Your fountain will depend on the chosen diameter of the bowl. The lid should either fit over the bowl or be very tight to the bowl so that it is difficult to tear off. But even if the lid doesn't fit very snugly on the bowl, you can drop glue in three or four places and the problem is solved.
Usually, the lid is first drawn up, so to speak, the whole appearance of your fountain. Depending on your idea, a hole is drilled in a certain place on the lid and a tube is inserted into it. At the beginning, it is desirable that it reaches the bottom of the bowl from below, and from above it is 5-10 centimeters higher than the calculated size of the fountain. Even if you don’t need these tolerances, you will always have time to cut off unnecessary ends, but it’s better to have them just in case. In the role of tubes, any kind of tubes, cambric and pipes are suitable. And it doesn’t matter what they are made of: let it be aluminum tubes or flexible PVC tubes, for example, from droppers.
Next, a base is made around the tube to create an appearance. Most often, a mixture of cement and pebbles is used. With cement, everything is clear, but I’ll tell you about the pebbles separately. Wherever you are (in the city, in the country, in the forest, at the sea, etc.), always pay attention to the pebbles. The more non-standard and bizarre the shape, the more unexpected its color, the better! And in general, try to notice all sorts of non-standard things (pebbles, twigs, roots, etc.) in order to use all these materials for the production of fountains in the future. When creating the base, simply throw cement on the lid and, while it has not hardened, sprinkle pebbles into it, immediately forming the landscape of the future fountain. Don't forget that the water needs to get inside the bowl and flow through the landscape. Therefore, try to make some kind of depression at the bottom of your landscape so that water collects there and immediately drill a hole there (but a small one, otherwise the water will immediately flow into the bowl. And it is much better when the water remains in the depression for a short time. It turns out a small lake) . If you do not get along with cement, then you can use all kinds of adhesives, sealants, polymer compounds, epoxy resins. Our task is to create a landscape from natural material, fastening it together and with the base. The fastening material must be moisture resistant so that the artistic composition does not fall apart.
You can also use various hi-tech tricks. Forged landscapes, bronze, metal, plastic or glass.
You can produce complex textures and geometric patterns using a 3D printer. Then your fountains will have no competition at all.
Video: 3D printed tabletop fountain
If you do not consider yourself an unrecognized artist or sculptor, it does not matter. Sometimes a masterpiece is obtained from just a pile of pebbles. Add absolutely any materials (usually they are just glued to the landscape), but do not forget that water is a very patient cutter. Therefore, it is desirable to use materials that do not decompose with water. Otherwise, there will be an unpleasant smell of rotten water. But even with organic materials there are very interesting cases. For example, when I wanted to plant a real swamp moss on the fountain, then quite unexpectedly it began to become covered with white mold. But the most interesting thing is that there was no smell! The mold itself is a penicillin, and most likely it even helped filter the water. But it turned out very nice. The fountain has turned into a real living organism that does not age, because. swamp moss can live for centuries without growing in size.
After external design, you just have to connect the pump to the supply tube and connect it to the power supply. ALL!
After you try to make 3-4 fountains, try adding light to the landscape elements. I recommend using LEDs. First, you can choose the colors of the LEDs you want to highlight some specific parts of your landscape. Secondly, at the moment LEDs are sold with different light power, flashing, with fading pulsation, etc., which will also help you a lot when decorating the landscape. Thirdly, they are almost eternal, do not burn out and are not afraid of contact with water.
Let me give you another piece of smart advice. It is desirable to add a pair of relay contacts to the receiving container at a certain level (it is set experimentally) so that the water closes them and when the water level drops below the specified rate, the electrical circuit breaks so as not to drive the pump without water. But here there are two options. The first and easiest is to turn off the power to the pump.
But, as practice has shown, very few people read the instructions for using a decorative indoor fountain, which says that when the fountain stops working, you first need to add water. Therefore, it was necessary to improve the fountain a little and add a circuit to it, which, when the contacts are opened, lights up a flashing “Add water” sign below and emits an intermittent low signal. At the same time, safety precautions are observed, since the power supply of the pump and the circuit ranges from 3 to 12 volts and will not affect the touch of water with your hands.
That's all! Then turn on your imagination and create! For example, when I made a lot of landscape-type fountains, I started making fountains in the form of water mills, adding various moving figures to them. It turns out great!
Video - how to quickly and easily make a fountain for your home
The essence of business
All this is usually sold in the city market, or through social networks. There is always a crowd in the market near my trading place. Fountains typically sell for between $50 and $150. But some copies left me and at a price of $ 300.
Some clients themselves later approached me and asked me to make a custom-made fountain, taking into account their personal wishes. Naturally, the price in this case was automatically increased by 50%. You can also walk around the offices and offer them decorative fountains. A lot of people are willing to take it. Only it is necessary to make fountains for offices a little more massive and larger in size. For example, for one office, I made a fountain 150 cm high, and it occupied a square 100 × 100 cm wide.
The profit arithmetic here is very simple, so you yourself can calculate the profit at the cost. If a copy is not sold for a long time, then I lower the price on it and they immediately buy it.
