Installing your own toilet. How to install a toilet with your own hands: installation steps and useful tips. Common Errors and How to Fix Them

If your plumbing is out of order, you often need to replace the toilet. This process has many nuances. It is important to choose the right plumbing fixtures. And also you should know how to install a toilet bowl with your own hands. You can watch a video of this process on the website. To carry out such work, you can contact the plumbers, or you can try to do the installation yourself.

Self-installation of plumbing will save significant financial resources

Remember to check all dimensions before purchasing equipment. They must be combined with the dimensions of the toilet. Consider the nuances of the flooring and its quality.

There are certain requirements for installing a toilet bowl with your own hands. You should know about them:

the normal installation height of plumbing equipment is about 40 cm;
each product has its own requirements for the functioning and cleaning of the internal container.

The shape of the bowl is plate-shaped, visor, funnel-shaped. The most popular model is the visor.

Useful information! It is better to choose a design with a circular flush, rather than a straight one. This option provides processing of more than 90% of the surface.

What will be needed for work?

Before you install the toilet with your own hands, the video will show you how, you need to choose the right tools. You will definitely need a drill, an adjustable wrench, two types of drills, a hammer for driving dowels, a rubber spatula and a screwdriver.

In some cases, leveling of the floor surface is required. Before work, it is important to turn off all plumbing devices.

Dismantling of old equipment and preparatory work

Before installing the toilet bowl on the tiled floor, dismantling work is done. Disconnect the drain tank, unscrew the hose and remove all fasteners. It is important to unscrew all fasteners for the tank. Then disconnect the drain from the sewer line. If the drain device was attached with cement coating, then you will need a hammer and a chisel.

Preparation for installation includes the study of certain nuances of installation. Any modern equipment is equipped with special instructions. During installation, special attention should be paid to the float, which helps to regulate the pressure and volume of water.

Useful information! After dismantling the plumbing device, it is important to plug the resulting hole. Since not only poisonous vapors enter through it, but there is also a danger of an explosion.

Related article:

How to disassemble a single lever mixer. From the article you will learn what the mixer consists of, what are the malfunctions, and how to fix them yourself.

Mounting order

To properly install, you should study the video. Do-it-yourself toilet installation has many subtleties. To carry it out you will have to do the following:

clean the area inside the sewer line;
it is worth installing a corrugated pipe on the outlet, and then putting it on the bowl;
you need to put a special gasket or fabric under the landing heel;
carefully move the container closer to the wall;
on the floor covering, the installation sites of the structure are drawn;
then the equipment is removed to the side, and holes for fasteners are drilled;
dowels are placed in holes made by a drill;
screws and washers are screwed into the inserted dowels;
apply sealant along the edges of the corrugation;
fix the drain tank with bolts with corrosion protection;
install flexible water hoses. They can be sealed with flexible silicone or rubber washers.

After carrying out the work, you need to check for leaks at all joints. Do not use windings for sealing, which will cause leakage. After installing the equipment, do not immediately use it. Give the silicone time to dry. This will happen within 6 hours. You should not feel sorry for the sealant, but it should not be inside the pipe.

Important information! To make holes in a layer of tile, the top layer must be drilled and then an impact drill is used.

Related article:

A detailed overview of different types of bath faucets with photo examples and prices in a special publication of our portal.

Installing a regular toilet

To understand how to properly install the toilet, you need to watch the video, where all the installation steps are disassembled step by step. Even a standard toilet bowl can have various geometric shapes, suitable for both classic interiors and modern ones.

The main advantage of such equipment is the ease of installation. It is much easier to change than hanging models. Compact devices are mounted in the traditional version or mounted on the wall. Similar models can be purchased at an affordable price.

The downside is the difficulty in maintenance. It is better to choose models with no niches where dirt can collect.

How to install a toilet with your own hands: video tutorial, equipment with a hidden tank

A hidden tank is mounted away from the main equipment and covered with decorative details. Such products differ from standard devices in fastener options. For installation of a similar design, floor and suspended models are used. The tank can be installed on the other side of the wall and even in a separate block. When located in the toilet, a special hatch is placed on the surface, which is designed to carry out various work in the tank. The difference from the standard version is in the method, when using which the valve of the drain system is moved.

Do-it-yourself toilet installation installation: video

There are special video instructions: how to install the installation for the toilet. The best placement of the device is the area away from the door. At the same time, consider the proximity of communications so that you do not need to pull them through the entire room.

During preparation, the layout of the planned structure is carried out. Frames and their connections are indicated. The mounting points of the installation frame on the wall and floor are applied.

This design has its own characteristics:

the drain button is usually located at a height of a meter from the floor;
the distance from the structure to the wall is 150 mm;
between the surface of the wall and the tank should be left about 20 mm.

Important information! Installation should be carried out in a niche where the riser and the entire sewer structure are located.

Installation of a suspended structure

The table shows the step-by-step installation of the suspension device.

Image	Installation steps
	Prepare all the necessary improvised materials and a set of tools. Also mark up the design.
	Marks must be put on the floor and walls. A line is drawn on the wall showing the axis of the device. It is important to note the gaps to the wall and to the drain tank.
	Installation starts with fasteners. After installing the dowels, the brackets and anchors are mounted. The body of the structure is mounted using special bolts. The vertical elements are aligned by fitting to the anchor thread.
	Connected to communications. In this case, plastic pipes are used.

Installing the floor unit

In the table you can see the installation of outdoor equipment.

Image	Installation steps
	The drain device is being assembled.
	The tank is installed. At the same time, a seal is put on the drain hole. Bolts are inserted into special holes and fixed from below with nuts.
	Installation and connection of equipment.
	At the end of the work, all joints and connections must be coated with sealant.

Compliance with the technology of installation work will help you install the toilet yourself in the shortest possible time.

You may also be interested in:

Connecting the washing machine to the water supply and sewerage independently, quickly and efficiently How to make heating in a private house from polypropylene pipes with your own hands

In cases where there is a desire to save on the services of specialists or just learn a new building skill, information on how to properly install a toilet will come in handy.

What you need to install

Before you install the toilet with your own hands, you need to take care of the availability of a number of tools:

perforator or impact drill;
drill with a diameter of 8-10 mm (depending on the diameter of the dowel for fixing the toilet bowl);
tile drill (if installation is done on a tile or ceramic plate);
wrench;
set of wrenches;
a hammer;
sealant (either in a special tube or together with a sealant gun);
screwdrivers (flat or Phillips, depending on the design of the toilet);
transitional cuff made of rubber 123 × 100 (if you need to connect to a cast-iron socket);
a set of fasteners for installing a toilet bowl (if it is not included in the kit);
rags and a container for draining the remaining water from the old toilet.

Before you install the toilet, you need to do some preparatory work. For example, you need to decide how exactly to connect the new toilet bowl with the sewer socket. The following options are possible:

Corrugated cuff. This method is the most economical, but in this case the toilet cannot be attached close to the socket. This matters if the bathroom is small.
Straight cuff. It firmly and hermetically connects the bowl of the structure with the socket of the sewer system.
Eccentric cuff. It is convenient if the connection centers of the system and the socket are displaced.

Next, it is advisable to replace the old flexible water supply. The choice of liner is based on the distance from the connections on the cold water pipe to the connection of the toilet filler mechanism. To this length should be added 15-20 cm.

If necessary, you need to pre-purchase adapters for threads at the junctions of flax or FUM tape.

In the case when a wooden stand has been preserved under the old toilet, it must be removed. A nail puller or puncher will help with this. The resulting void can be sealed with a cement composition, preferably a quick solidification, and a spatula.

Removing an old toilet

First you need to turn off the water. Disconnect the flexible hose, flush the toilet.
Then you need to unfasten the drain tank. You can carefully, or you can use a hammer (in case the old toilet is no longer needed).
You can quickly remove the toilet bowl with a hammer and a perforator.

Carefully, so that the fragments do not fall into the sewer system, use tools at the place where the toilet bowl is attached to the floor and the junction of the device with the sewer. Then the old bowl must be removed, pouring out the water that remains.

Wood plank removal and floor leveling

After the old toilet is removed, you need to thoroughly clean the sewer socket from dirt and rust. Install a rubber transitional cuff 123×100 into the socket, pre-coated with sanitary sealant.
Then plug the hole with a rag so that odors do not interfere with further work.
Next, you need to remove the wooden board and fill the resulting void with repair staff.
Align with a spatula to the level of the floor.

Marking and installation of dowels

Put the bowl of the new toilet bowl in the planned place. Mark out through the holes in the bowl on the floor so you can see where to drill. The holes in the toilet bowl are located at an angle, in which case you also need to drill at an angle.
After marking, the toilet can be removed. Next, you need to drill holes in the previously marked places and insert the dowels.

Toilet cistern attachment

In accordance with the instructions that came with the toilet, you need to install the fittings for the drain tank. There are some peculiarities in this procedure.
It is necessary to tighten the nuts of the drain and fill valve manually, while at the same time holding the valve itself, thereby protecting it from turning and damaging the gasket.
The valves must be installed so that during operation the moving elements do not touch each other and the walls of the tank.
In case of uncertainty, a sanitary sealant should be used as the walls of the tank and gaskets.

The drain mechanism is available in a collapsible type to facilitate the installation process.

Installing the toilet bowl

The connecting cuff is attached with a petal part to the adapter cuff 123 × 100, inserted into the socket pre-treated with a sealant. The outlet of the toilet bowl is inserted into the adapter sleeve until it stops.
It is necessary to turn the cuff so that the toilet bowl takes a flat position, and all the holes of the fasteners coincide.
The bowl is fixed to the floor surface with screws with plastic washers. In cases where the floor surface is uneven, use spacers made of pieces of plastic to level the toilet before finally tightening it.

Connecting the bowl and drain tank

Before you install the drain tank on the bowl of the structure, you need to put a gasket between them. For reliability and to avoid displacement of the gasket, it is better to glue it to the bowl with sealant in advance.

After attaching the tank to the bowl, tighten the screws evenly. After that, install the tank lid and the drain button. Then fix the flexible eyeliner.

System Function Check

At the end of all work, you need to check - draw water into the tank and make a test drain. The amount of drained water can be adjusted, how to do this is written in the instructions.

Inspect all components for any leaks. If they occur, check the tensile strength and, if necessary, disassemble the assembly, re-treat with sealant, then tighten properly.

If the cause is a defective part, purchase a new part and replace it.

Install the toilet seat and fill the gaps between the toilet and the floor surface with sealant.

Doing such work with your own hands is not difficult if you follow the above recommendations and rules. Good luck!

How to install a toilet with your own hands - step by step instructions with Video

What is needed to install a toilet. Step-by-step instructions for dismantling the old and installing a new toilet with your own hands

How to install a toilet with your own hands

From our article you will learn how to install a toilet bowl with your own hands. This is a fairly simple operation, provided that you are able to shut off the cold water supply, and the supply and sewer pipes do not need major repairs. In this case, we will install a toilet bowl with a lower cistern. This option is easier, since most of the weight of the tank in this case falls on the toilet. When installing a toilet with an upper tank, you will need reliable fasteners to support the weight of the latter (this is not a problem for brick walls, but in the case of walls made of hollow materials, you will have to resort to special tricks).

1. If during the repair undertaken in the bathroom the floor height has changed somewhat, it is necessary to compensate for the difference with the help of an eccentric cuff - the so-called corrugation for the toilet bowl (for sewage) and a flexible hose (for supplying cold water). Large height changes will require the skills of a professional plumber.

2. If the floor in the bathroom is not even enough, it is better to install the toilet bowl on silicone sealant. Small wood/plastic wedges can also be used, but sealant is essential here as it distributes the weight of the toilet evenly.

3. If the sewer pipes go down, through the floor, and not through the walls, you will need a rectangular elbow or a flexible corrugated cuff. This is not the only difference, but the main one.

Assembly and installation of the toilet bowl

2. Follow the manufacturer's instructions for assembling the inside of the tank. The sequence of actions depends on the type of drain system used in the model you have chosen.

3. Make sure all parts are securely fastened, but do not overtighten the bolts and screws.

4. In most cases, bolts are sold with the cistern to attach it to the toilet. Be sure to put washers and rubber cones on before inserting bolts into their holes.

Installation of a toilet bowl with a cistern installed

6. Insert the corrugated cuff (corrugated extension) into the sewer pipe, making sure that it fits snugly. In our example, a simple straight connecting cuff is required. (When connecting the toilet bowl to a cast-iron pipe, you will need a transition cuff with a diameter of 110 mm. See photo. It must be liberally lubricated with silicone sealant and inserted into the cast-iron pipe, which was previously cleaned of dirt, see photo. Only after that you can insert a corrugated plastic cuff into it.

7. Move the toilet to the sewer pipe. Make sure that its outlet is flush with the installed nozzle. Most likely, the way it is. But if not, and the offset is quite large, then you will need to use an eccentric bellows.

8. Gently place the toilet in its place by placing the cuff over the outlet.

9. Make sure the tank is level with a spirit level along the back wall. Through the back wall of the tank, mark the places on the wall where you have to make holes for fixing it.

10. Do the same with the toilet itself: check its levelness with a spirit level and mark the mounting holes on the floor, while trying to be as accurate as possible.

11. Mark the edges of the base of the toilet with a pencil on the floor. Knowing the exact position of the “leg” will come in handy when you finish the preparatory work and proceed to the final fixing of the toilet.

12. Move the toilet away from the wall. Drill holes for mounting the tank, focusing on the marks on the wall. Select (taking into account the material of the wall) and insert the dowels.

13. Drill holes in the floor at the points you marked. When drilling ceramic tiles, you will need a hammer drill and a concrete drill bit. At the beginning of drilling, the pressure on the punch should not be large; after passing through the tile layer, the pressure can be increased. Insert the dowels into the holes. If the floor is wooden, as in our case, they are not needed.

14. Before installing the toilet in place, apply silicone sealant to the floor along the line marked with a pencil, corresponding to the border of the base of the “leg”.

15. Put the toilet in its place. Screw the cistern to the wall by inserting washers between the screw heads and the cistern wall. Don't overtighten the screws.

16. Screw the base of the toilet to the floor. In this case, the same rules apply: firstly, do not forget about the plastic washers, and secondly, do not tighten the screws too tight.

Connecting the water and finishing the installation

17. Connect the tank to the cold water pipe. With a high probability, you will need a flexible connecting hose for this. The connection point depends on the position of the inlet pipe on the new tank.

18. Turn on the water by opening the shut-off valve and check for leaks at all connections. Also check the tightness of the junction of the toilet with the sewer and coat all connections with silicone sealant.

19. Install the toilet seat as designed. If necessary, adjust the seat to exactly match the shape of the toilet.

20. Apply silicone sealant around the base of the toilet. Smooth out any unevenness with a damp sponge, achieving a neat look.

How to install a toilet with your own hands - step by step instructions Photo

Follow our step-by-step instructions and you will learn how to install a toilet bowl with your own hands and what is needed for this.

Do-it-yourself toilet installation

If this is your first time thinking about installing a toilet, this article is for you. And it’s better if you have time to read it before you go to the store for a new “faience friend” or before the start of finishing in the toilet room.

The fact is that modern toilet bowls are so different that they have a very different type of attachment, flush, sewer supply, etc. So, ideally, planning which toilet you have to mount with your own hands should begin already at the design stage of the toilet.

Do-it-yourself toilet installation

And what to do if there is an old “throne” in the toilet - how to remove it, avoiding the global flood? We will also talk about this in the article. Features of the installation process, a step-by-step guide and a few tips from the masters will help you save money and mount the toilet with your own hands without any problems.

Planning space in the toilet room

It is impossible to plan a comfortable toilet without taking into account the features of the toilet bowl that is to be installed there.

To understand what exactly needs to be done, you need to know:

whether it is necessary to dismantle the toilet bowl, which has served its purpose and carry out major repairs in the toilet (including cladding, repair and supply of sewer communications and floor screed);
what are the dimensions of the new plumbing - will it not clutter up the space and will it allow your door to open quietly;
what mount your future toilet has;
what is the way to flush the toilet;
At what height do you want to install plumbing.

If you know the answers to all these questions, it remains only to dismantle the old one (if necessary) and install a new toilet bowl.

Recall that floor plumbing is divided into several types. It differs in form and its device.

The drain tank can be combined with the toilet bowl and independent (wall-mounted).

Toilet bowls are attached to the floor: on 2 and 4 attachment points, on the corners.

Down with the old toilet!

Surely your toilet, which needs to be dismantled, is not wall-mounted, which means that it is attached to the floor. It will be possible to remove it from the toilet in just 7 steps.

Turn off the water and drain it from the tank in the toilet.

Before breaking the toilet, you must turn off the water supply and unscrew the tank

Removing an old toilet

If the neck is disconnected from the pipe, and the toilet is tightly glued to the floor with mortar, then you need to take a chisel and carefully chip the pedestal from the mortar, you can use parts

If there are no plans for an old toilet, and you are seeing him off on his last journey, then after swinging it, you can split it with a sledgehammer so that it is not difficult to carry it out. You will also have to do the same if the fasteners of the old plumbing are cemented.

After dismantling the toilet, evaluate the condition of the pipes in the room. Cast iron create many problems; before installing new plumbing, it is recommended to change them to plastic. Also, plastic pipes greatly facilitate the process of installing a toilet bowl and distributing sewer drains (by the way, you can also read about installing plastic pipes with your own hands on our website).

Self-installation of plumbing "step by step"

For normal operation, the toilet bowl needs a flat, lined or specially prepared surface of the walls and floor.

First, we connect the drain of the toilet bowl with the help of a corrugation to the outlet of the sewer pipe-riser. You can also use a hard tube. The best option is if the toilet drain enters the riser without extension corrugations, etc. To seal the drain, we use a ring with a rubber border. It is important to consider that rubber does not tolerate cement and similar coatings on its surface. But the sealant is quite suitable.

Toilet installation - cuff

We take the cuff and apply silicone sealant and install it in the pipe

Then we take a corrugated pipe and also apply silicone sealant

We install the corrugation in the pipe

Then we carefully move the toilet bowl and install its outlet into the corrugated pipe seal

To prevent water from getting under the toilet during mopping, this place can be sealed with silicone sealant

We fix on the floor: 3 types of fasteners

The first option for floor installation is anchors embedded in the screed. During the pouring of the floor, long anchors are fixed at the place where the toilet bowl and its fasteners will be located. After the screed dries and the floor is finished, a toilet bowl is attached to the anchor. This is the most difficult method of fastening, since it is difficult to install the anchors so evenly that the toilet stands on them without problems. It often happens that inexperienced builders choose too short anchors, on which it is then impossible to screw nuts. The anchor embedded in the floor must be at least 7 cm above the finish surface in order to screw the toilet to it. Gaskets are required under all nuts so that the surface of the toilet does not crack.
The second option for securely fixing the toilet bowl on the surface during the overhaul of the toilet is installation on a wooden base. The main thing is that the board strictly matches the size of the base of the toilet bowl. When pouring the floor, the board is prepared by hammering nails into it. Then it is laid in the solution with nails down. After the screed has dried and the room has been finished, the toilet bowl, previously planted on a layer of epoxy resin, is screwed to the board using ordinary screws. Under them, rubber or polymer gaskets are also needed.

You can fix the toilet with a wall tank without screws, for one resin. True, with this method of fastening, it is first necessary to clean the surface of the tile so that the glue holds better. When using "epoxy" it is important to allow freshly installed plumbing to dry properly and gain a foothold on the floor surface.

Fixing the toilet to the wall

How to install the installation

Wall hung toilets are being used more and more. Their installation is not much more complicated than usual (by the way, you can read about installing a toilet bowl with your own hands on our website). A wall-mounted toilet, as its name implies, will not have contact with the floor surface. It is suspended using a metal frame, which is attached to the load-bearing wall itself. The cistern and pipes of the toilet in this case are behind a false plasterboard wall. If the mounted plumbing has an open tank, then it will be possible to fix it on the wall itself, but then the sewer pipe should be inside the wall. The same anchors embedded in the wall or in the supporting frame will hold the structure.

Installing a toilet on a pedestal

After fixing the toilet bowl on the wall or on the floor, it remains only to assemble the toilet bowl. A tank is placed on the base, already securely fixed, or a pipe is connected to it from a tank hung on the wall.

Installing a toilet on a pedestal

It remains only to check if the toilet is working, and if there are any leaks. We turn on cold water, wait until the tank is filled, adjusting the filling level. We set up the locking mechanism according to the instructions. Rinse and see if it flows from the drain.

The last step is to screw the toilet seat. But here you, for sure, can already handle it yourself.

Before buying plumbing, first decide on the type of drain that suits you. If you do not plan to change the supply of the sewer riser, you must choose the same type as in the toilet that has worked out. Remember: no adapters will help to qualitatively connect the toilet bowl to the type of outlet that is not suitable for it.
Do not leave the choice and purchase of a toilet at the final moment of repair: it is better to prepare a place in the toilet in advance to facilitate the installation of plumbing.
Invest in nickel-plated bolts and anchors to secure the toilet to the floor or wall. They do not rust, which means that ugly streaks and sticking of bolts are excluded.

Do-it-yourself toilet installation was successful

Do-it-yourself toilet installation - step by step instructions!

Learn how to install a toilet bowl with your own hands. Step by step instructions, tutorials, photos + videos and the best tips from professionals!

How to install a toilet yourself

With "straight" hands, most of the housework can be done independently. This category of work includes the installation of a toilet bowl. Knowing the sequence of actions, installation or replacement can be done by hand.

Do-it-yourself toilet installation is a task of medium complexity

Types of toilets

In this article, we will consider not the features of the flush or the shape of the bowl, but those design features that determine the list of installation work.

According to the installation method

The toilet itself consists of a sanitary bowl and a drain tank. The bowl can be floor mounted or suspended. If the bowl is suspended, then the tank is concealed - built into the wall. In the case of a floor bowl, there are three options for fixing the tank: on a special shelf on the bowl (compact), separate, connected with a flexible hose, in an installation (frame hidden in the wall).

Typical sizes of toilet bowls of different designs

The advantage of a floor-standing toilet with a conventional flush tank is ease of installation. It can be installed without starting repairs. The disadvantage is that compared to the hanging one, it takes up more space, looks more heavy. Accordingly, for suspended models, installation is difficult - it is necessary to fix the supporting structure - installation - in the wall. Perhaps it is only during the repair.

Release to the sewer

The choice of toilet for release into the sewer depends on the location of the sewer pipe. They happen:

with horizontal outlet;
oblique release;
vertical.

Types of outlets (outlets) of the toilet bowl

If the pipe is in the floor, a vertical outlet is optimal. If the exit is in the floor, but is close to the wall, the oblique toilet is most convenient. The horizontal version is universal. Using a corrugated pipe, it can be connected both to the wall and to the floor.

Installing a toilet bowl with a compact cistern (floor version)

A toilet bowl, a tank, a drain device and a float are usually brought from the store separately. Before installing the toilet, everything except the float must be assembled.

What does a floor-standing toilet with a "compact" cistern consist of?

The process begins with the installation of a drain device. It comes assembled, you only need to install it in a hole in the bottom of the tank. A rubber gasket is placed between the drain device and the tank.

We install the drain mechanism inside the tank, placing a pre-rubber gasket

On the reverse side, the supplied plastic washer is screwed onto the pipe. It is tightened by hand, then - using a key, but very carefully, since it is easy to break the plastic. To prevent the drain device from spinning, it must be held by hand.

Tighten the nut carefully

The next step is to install the mounting screws on the tank. They are also included in the standard package. These are long thin screws made of galvanized or stainless steel. They are inserted into two small holes at the bottom of the tank, rubber gaskets are put on, then washers, and only then nuts are screwed on.

Install the mounting screws on the tank

Before installing the tank on the toilet bowl, a gasket (included) is placed under the tank. To prevent odors from leaking out of the sewer, it must be “planted” on a sealant. First we coat it on one side, put it on the toilet bowl, coat it on the other, put the tank.

Lubricate the gasket with silicone, put on the toilet

Lubricate on the other side

We install the tank on the shelf of the bowl, passing the screws into the corresponding holes. We put washers, nuts on the screws from below, tighten them. At the same time, make sure that the tank is level.

Installing the bowl on the bowl

Next, we put a float - a device for controlling the water level in the tank. There are two holes in the top of the tank. Here we insert the device into one of them. It is mounted on the side from which the water supply will be connected.

We put a float in the tank

We wind a little flax on the outlet pipe, coat it with sanitary paste, install a corner (brass or stainless). Do not tighten the connection strongly, do not clog that the pipe is made of plastic.

Floor mounting

The toilet is almost assembled, you can put it in place. The toilet bowl is connected to the sewerage by means of a corrugated adapter. At the ends, it has rubber seals that fit snugly into the pipes and onto the toilet outlet.

Corrugation for connecting the toilet to the sewer

If the sewer pipe is plastic, the corrugation is simply inserted all the way. If the riser is cast iron, and not yet new, so that the smell does not seep through the microcracks, the pipe is cleaned to metal, washed and dried. A layer of sealant is applied around the circumference on a dry, clean metal (a little more in the lower part), then a corrugation is inserted. For greater certainty, you can go through the sealant on the outside of the joint.

In order for the installation of the toilet bowl on the old cast iron to be airtight, a layer of sealant can be laid under the corrugation

In any case, we insert a corrugation into the sewer pipe.

We insert the corrugation to the stop

The second end of the corrugation is put on the outlet of the toilet bowl. This is the connection of the toilet to the sewer. Everything is so simple. There is only one caveat. So that it can be removed later, the corrugation outlet and the outlet of the toilet bowl are lubricated with soap moistened with water, only then the bell is put on. If this is not done, it will be problematic to remove the toilet without damaging the corrugation. But you still have to drill holes for fasteners. It will be much more convenient to remove, rather than trying to move a partially fixed device.

Putting the corrugation on the outlet, we expose the toilet as it will stand. Having installed the lid on the tank, we check that there is a place for it. Next, you need to sit down, check the comfort of use, if necessary, correct the position. Then they take a pencil or marker, inserting it into the holes in the sole, mark the places for installing fasteners.

Mark places for fasteners

Having removed the toilet bowl, holes for the dowels are drilled in the marked places. If the kit comes with plastic fasteners, do not use it - it will break in a few days. It is necessary to immediately put powerful dowels.

If the toilet is installed on a tile so that it does not crack, it is better to pierce the glazed surface. They take a self-tapping screw, mark it, hit it with a hammer several times. This is what is called "pinching". Then they take a drill or a puncher and drill a tile, turning off the impact mode. After the tile is passed, you can turn on the perforation mode.

Drilling holes for fasteners

We put plastic plugs from dowels in the holes. They must be in the same plane with the floor. If there is a thicker edge, cut it off with a sharp knife.

We sweep the floor, removing dust at the installation site of the toilet. We put it in place, insert the dowels into the holes, twist them with the appropriate key. It is necessary to tighten the bolts alternately on one side, then on the other. Tighten until the toilet becomes firmly, without play.

The final touch is the connection to the water supply. Connect the outlet of the water pipe to the tap installed on it with the corner on the tank, which was connected earlier. This requires a flexible hose. At its ends there are union nuts (American), so there will be no problems with fastening. Tighten well, but without fanaticism.

How to install a wall hung toilet with installation

To install hanging toilets, the outlet of the sewer pipe must be located near the wall. The specific distance from the wall is indicated by the manufacturer, but should be small - from the far edge of the order of 13-15 cm. If the exit from the floor, there is a solution - a special overlay, with which the drain is transferred closer to the wall.

The installation of a wall-hung toilet begins with fixing the stops to the wall to the installation frame. They are attached two at the top and at the bottom. With their help, the distance to the wall is adjusted, the frame rises and starts.

Install top stops

The upper stops are in the form of rods, adjustable with a socket wrench and a screwdriver. The bottom stops are more like plates, they are also adjusted with a socket wrench but with a side head.

Bottom stops and height adjustment

The assembled frame is attached to the wall, its center is exposed above the middle of the sewer outlet. The mark on the frame rises or falls to the height required by the manufacturer (there is a mark on the frame, also indicated in the passport, usually 1 meter).

Align height and away from wall

Using a bubble level, the horizontal and vertical installation of the wall-hung toilet installation is checked.

By adjusting the height of the stops, an equal distance from the wall, set by the manufacturer, is set. How convenient it is to do, look at the photo.

The specified distance to the wall is set

The exposed frame must be fixed to the wall. In appropriate places put marks with a pencil or marker, drill holes. They are equipped with plastic housing dowels. Most of the hanging toilets are imported, and they recommend planting the dowel bodies on the sealant. Some of the sealant is squeezed into the drilled hole, a dowel is inserted. Then, before installing the fastener itself, the sealant is applied to the plastic case.

In a fixed installation, you can put connecting elements - branch pipes, couplings. They are all included and simply snap into place.

Pipes and connectors are installed

Pipes from the tank and sewerage are installed

Next, metal rods are installed on which the toilet bowl will be held. They are screwed into the corresponding sockets, silicone seals are put on top (in the lower photo these are two rods above the sewer outlet).

Toilet holders are installed, the sewer pipe is fixed

The sewer pipe extends to the desired distance, is fixed in a predetermined position with a bracket. It covers the pipe from above, is inserted into the groove until it clicks.

Next, water is connected to the tank. Open the tank lid (it is latched), the plug on the side surface is removed. Right or left - depends on where you have water. A corrugated pipe is inserted into the opened hole, the counterpart is inserted from the inside, everything is connected with a union nut. Tighten without applying excessive force - it's plastic.

Connecting the installation to the water supply

A tee is installed inside the tank, a pipe (usually plastic) is connected to the desired outlet. They do this with the help of an adapter and an American.

Water pipe connection

A hose from the tank is connected to a special tee inlet. It is flexible, in a metal braid. Tightened with a cap nut.

Connect the hose from the tank

Install the cover in place. In principle, the installation for the toilet is installed. Now we need to close it. To do this, make a false wall of moisture-resistant drywall. It is recommended to put two sheets, but you can use one. Drywall is attached to the installation frame and to the mounted profiles.

Fixing the false wall to the installation frame is mandatory

The toilet bowl is put on the pins, its outlet goes into the plastic socket. The connection is tight, no additional measures are required. This completes the installation of the toilet with the installation.

Do-it-yourself toilet installation: floor-standing, hanging with installation, instructions with photos, videos

Self-installation of the toilet will save a substantial amount of money. With your own hands, you can install both a floor model and a pendant one, with an installation.

Manufacturers offer a wide selection of plumbing. Each model has its own and imposes certain requirements on the installation procedure. Do-it-yourself installation of a toilet bowl is possible, but subject to the manufacturer's recommendations. We suggest that you familiarize yourself with the existing types, the procedure and features of the work, so that self-assembly is carried out in accordance with regulatory requirements.

In order to correctly place the key ones, you should prepare a drawing on a scale on which the plumbing will be located taking into account sanitary and hygienic standards. You can create a comfortable layout by adhering to the following recommendations:

The area in front of the toilet must be at least 60 cm long;
On the sides of the toilet, a free space of at least 25 cm wide should be provided;
In front of the sink, the platform should not be already 70 cm;
Bidet and toilet should be fixed at a distance of at least 35 cm;
it is worth fixing at a height of 60 ÷ 80 cm above the floor surface, and - 95 cm.

The recommendations given are relevant for those for which it is enough to adhere to standard norms, principles of practicality and comfort. In apartment buildings, the arrangement of plumbing is regulated by SNiP, which are developed taking into account the safe operation of communications. When planning to do the installation yourself, you should definitely familiarize yourself with the indicated standards.

The basics of choosing the right toilet for your home

When choosing the right model, you should take into account the features. Worthy of attention:

The area of \u200b\u200bthe room, affecting the dimensions of the purchased plumbing;
The presence, geometric parameters and location of the external. Consider how far it will be from the intended installation site of the toilet bowl;
The location of the sewer pipe;
Release angle. The best option is to mount a model with an oblique outlet. If the measurement shows a slight match, you should purchase a special adapter together with the plumbing - a drain corrugation.

Manufacturers offer plumbing fixtures of various configurations, which have their own mounting features. The division can be made on the floor and mounted models. The latter require less space to install and are more attractive. This is the right choice for . Floor models are more reliable and practical.

a hammer;
drill (perforator);
yardstick;
marker for marking;
wrench or set;
pliers;
screwdriver.

It is also worth preparing:

FUM tape;
flexible hose;
corrugation;
silicone sealant with a gun.

Removing an old toilet

When dismantling, you should follow the instructions in accordance with which the installation of new plumbing was previously carried out. Do-it-yourself toilet replacement begins with the following work:

block the water supply inside the drain tank;
drain the water inside the tank;
unscrew the fastener of the tank. With a large thickness of lime deposits or the presence of rust, it is worth fixing the bolt head with a screwdriver and unscrewing the nut with an adjustable wrench;
removing the barrel tank, unscrew the fasteners that fix the product;
disconnect the drain from the sewer pipe. If cement coating was previously used during installation, cement is chipped off with a chisel;
drain the rest of the water from the toilet and set it aside.

Advice! After dismantling, the sewer pipe hole should be closed with a cloth stopper to prevent it from clogging.

Preparing a new toilet for installation

Having decided to do the installation yourself, you should figure out how to assemble the toilet. The structure of any model includes two components: a bowl and a drain tank. At the preparation stage, these parts should be connected to each other using the fasteners included in the delivery.

First, collect the drain tank. For this, a drain mechanism and a float are installed. As a rule, the installation of the drain mechanism does not cause difficulties, since it is initially supplied assembled. It is inserted into a special mounting hole at the bottom and fixed with a plastic nut, on which a rubber seal is prudently put on. The cistern is attached to the toilet bowl using metal studs and nuts.

Attention! Rubber seals should be used in all connections.

DIY toilet assembly video will allow you to better understand the sequence of work:

How to install a conventional toilet with your own hands?

After the plumbing is assembled, it is worth clarifying how to install the toilet with your own hands. The work can be done in the following sequence:

A photo	Description of works
	We mark and drill mounting holes in the floor.
	We remove the formed dirt and dust.
	We hammer plastic dowels into the prepared holes.
	We install the toilet bowl at the place of future operation and fix its spatial position with the help of bolts.

If you have not yet figured out how to do the installation yourself, the toilet installation video will help you learn all the main steps:

Installing a toilet with a hidden cistern

Models with hidden tanks allow you to more efficiently manage the available space. They are easy to care for and look stylish. Installing a built-in toilet can be done in different ways. We offer you to familiarize yourself with the available methods and features of the work.

Installing a wall hung toilet with installation

To begin with, it is worth deciding on the model of plumbing. Its geometric parameters will affect the requirements for the mounted system. Hanging installation can be performed in the following sequence:

A photo	Description of works
	Frame height is adjustable.
	Installing the toilet installation in a metal profile 50 mm wide and screwing it to the floor through special mounting holes.
	A frame system is mounted to which it will be attached.
	Finishing material is attached.
	Silicone sealant is applied to the seat.
	The nozzles included in the delivery set are inserted into the mounting holes.
	The toilet bowl is hung and fixed with the fasteners included in the delivery.
	The water connection is made in accordance with the manufacturer's instructions.

Related article:

If you know the state of the art, it will be easier to check the value of different sales offers. The information from this article will be useful when performing installation operations with your own hands and for monitoring the actions of professional teams. In particular, they will help to agree correctly when determining the cost of the services of contractors.

Installation of floor models

Instead of a hinged model, you can install a floor model with a hidden tank. A large assortment allows you to choose the right option for the toilet in any style.

The technology in this case includes the following steps:

A photo	Description of works
	A niche is being prepared in which the tank will be installed.
	Do-it-yourself installation of a toilet bowl inside a niche and fixing it.
	The final finishing of the wall is carried out, and plumbing is installed in the allocated place.

The main types of toilet bowl fasteners to the floor

Fastening to the floor can be carried out in different ways:

On the installed in the screed. The hardware is placed in places corresponding to the attachment points of the floor bowl, and then the screed is poured. A rather complicated option, which can be difficult to implement with your own hands without the help of specialists. Insufficient length of the anchors can lead to the fact that after installing the toilet it will be difficult to put the nut on;

On a wooden base, the geometric parameters of which must correspond to the dimensions of the installed plumbing. Nails are first driven into the board, laid on the floor with nails down, and a screed is poured. During the installation process, the toilet is “sit down” on epoxy glue and screwed to the wooden base with ordinary screws;
On dowels. So most often the toilet is installed on a tiled floor. After installing the product at the place of future operation, the mounting holes are marked. Their depth should be sufficient to fix the bowl in place. For reliable fastening, the installation of the bowl can be done on epoxy resin and add a certain amount of sealant to the mounting holes.

Advice! To prevent cracking of the toilet bowl during installation, gaskets should be used during installation.

The main types of toilet bowl fasteners to the wall

Depending on the design features of a particular model, you can install a toilet bowl with your own hands using:

frame structure, which is a rigid frame attached to the wall and floor. The tank and pipes can be located behind a false wall;
block system. A more affordable and compact option that involves installation exclusively on a main wall. Installation is carried out in a specially prepared niche, which is then laid with bricks or blocks.

The main types of connecting the toilet to the sewer

To connect the system to the sewer, various adapters are used. Each species has its own distinctive features. We suggest that you familiarize yourself with the main varieties in order to have an idea of \u200b\u200bthe possible options.

Fan pipe or plastic pipe

If you decide to use an adapter, you need to know exactly the characteristics of the model that you plan to install yourself. When choosing the right option, special attention should be paid to the shape of the toilet bowl.

Products with an oblique outlet are mounted on the floor, with a vertical outlet - on the wall, placing the nozzle at a right angle. With an oblique outlet, it is permissible to install a “wall” by placing the connecting pipe at an acute angle. When replacing plumbing, you should purchase a model with a similar release, otherwise the use of adapters becomes impossible.

Attention! When using a plastic outlet or a fan pipe, it is unacceptable to change the geometric shape of the product.

Eccentric

When using an eccentric collar, according to experts, it is not necessary to ensure the tightness of the connection with a sealant. With the correct arrangement of special rubber seals, a reliable and tight fit of the mating elements can be achieved. If the pipes are cast iron, it is still worth using a sealant.

Corrugation

Corrugated pipe (corrugation) is used when other materials do not allow to cope with the task. How to install corrugation on the toilet? After fixing the system, work is performed in the following sequence:

One end of the corrugation is placed in the sewer hole. The joint must be lubricated with silicone sealant;
The second end is put on the outlet of the toilet;
Check the tightness of the connection.

Connecting the bathroom to the sewer is done in three ways. Each of them has its own characteristics. We offer you to find out how you can connect the toilet to the sewer and choose the most suitable option.

Bathroom with vertical outlet

Vertical outlet models are especially popular in European countries. The design of such plumbing products implies the presence of a siphon located in the bowl and an outlet pipe, which is directed downward during installation. This design is universal, and toilets with a vertical outlet can be installed at any angle to the vertical.

Do-it-yourself toilet installation is performed in the following sequence:

Marking is carried out on the floor;
A screw flange with a locking device is installed;
A sewer pipe is mounted in the center of the flange;
The toilet bowl is mounted on a flange;
The outlet pipe is fixed.

Bathroom with horizontal outlet

These products are sometimes referred to as direct outlet toilets. It is most widely used in Russia. Such products have a release pointing backwards. It is connected to the sewer pipe using a special cuff.

Models with a horizontal outlet are most often attached to the floor. The manufacturer provides special connecting holes that allow you to attach the toilet to the floor. Dowels or standard screws are most often used as fasteners.

Advice! Tighten fasteners carefully so as not to damage the product.

Toilet bowl with oblique outlet

A toilet with an oblique outlet can be connected as follows:

Cleans the socket of the cast-iron semi-outlet from the old seal and debris;
The toilet bowl is installed on the layer;
Excess cement paste is squeezed out. It must fill the semi-outlet socket by at least 2 cm.

This method is currently used quite rarely, since the dismantling of equipment is quite difficult. Most often, preference is given to regular anchor screws. However, some cement paste may be placed under the bottom of the toilet to compensate for the unevenness.

In some cases, silicone sealant can be used instead of cement paste. However, with a significant or uneven load, the sole of the product may crack.

Then, using a sealing sleeve, the outlet is connected to the cast-iron socket without displacement. It can be used to compensate for existing horizontal or vertical misalignment. To ensure maximum tightness, silicone sealant is preliminarily applied to the outer surface of the coupling.

Connecting water to the toilet bowl

To ensure the supply of tap water to the drain tank, you can use one of the following methods:

Bottom eyeliner. Such models create a minimum of noise in the process. However, in the event that during the installation process it was possible to ensure sufficient tightness;
Side eyeliner. They are easy to install. For do-it-yourself installation, it may be the best choice due to the ease of work. Creates a lot of noise in the process of taking water into the tank. Some models come with a longer pouring stroke to reduce the amount of noise generated;
Flexible eyeliner. In a similar way, models are most often connected in which the tank is located above the bowl;
Hard eyeliner. Such a system can last a long time.

Connection for all types of hoses is performed in the following sequence:

A separate tap is installed, with which you can shut off the water supply. The insert must be made in accordance with all the rules;
One end of the liner is connected to the tap and fixed with a special nut;
The second end is connected to the drain tank and fixed with a nut;
The mating surfaces are checked for tightness.

How much will it cost to install a toilet: price for work

If you want to know the price for the work - the installation of the toilet can be done for a different amount. On average, these services will cost:

We hope you enjoyed the article. Knowing how to properly install the toilet, the entire amount of work can be done by hand. Share in the comments how you coped with this task yourself. If you have any questions - ask. We will definitely answer.

Tools and materials

Simple set of tools found in every home

drill with a drill with a diameter of 10 mm;
screwdriver;
roulette;
marking marker;
screwdrivers and a set of wrenches;
knife for cutting the gasket.

You may also need a spatula to eliminate chips ceramic tiles. Materials required for installation, except for the bowl and tank:

corrugated hose;
gland - rubber gasket;
hose for supplying water to the tank;
sealing tape for sealing;
a faucet that will shut off water in plumbing;
silicone.

Important! When choosing a bowl, you need to take into account the size of the room, so as not to subsequently rest your knees on the door.

You should also provide for the installation of the product, what stock is available. Of course, it is better when the model of the bowl and the method of its installation are planned at the construction stage. But it happens that you just need to replace the old plumbing with a new one. Then you have to connect to the old sewerage system, and use drains that were made a long time ago.

Toilet corrugation prices

corrugation for the toilet

How to choose a toilet

The bowl should be easy to clean, be comfortable. Sizes are selected based on the growth of all family members. You can buy the model you like, which will be inconvenient to operate, because it will not correspond to the parameters of a private house or apartment.

Do-it-yourself installation of a toilet bowl in a private house is associated with certain costs and I want them to pay off in terms of convenience.

First of all, models differ in price:

Economy class;
middle class;
luxury plumbing.

Parts of elite plumbing are designed for a long service life and will not break just like that. Buying an expensive item, you can be sure that it will last a long time.

Another option is color spectrum. In large supermarkets, you can pick up any shade and embody the most daring design decisions.

Models available for sale:

from natural stone durable and reliable, service life is unlimited;
glass - completely transparent or with a pattern;
faience;
ceramic;
metal;
porcelain, which can reach up to 50 years;
plastic.

When buying, you need to carefully look at what is included in the equipment kit. It may happen that the bowl and tank sold separately.

In addition to external characteristics, you need note:

to the height of the equipment;
type of construction - suspended, floor, wall floor;
what type of flush - reverse or direct;
the method of draining from the tank is one or two-button.

It will cost more, but the structural elements will be hidden in the wall, which will save some space in the room. The reverse flush is better because it washes the bowl completely. allows save water.

Important! When choosing a design, it is worth checking it for cracks, chips.

Prices for toilets

Varieties of toilet bowls

Plumbing products distinguish drain design:

horizontal - the drain is located in the floor;
vertical - parallel to the floor;
oblique - at an angle of 30 degrees to the floor.

Tanks are:

Separated when they are connected to the bowl by a pipe. How to assemble a toilet bowl and a tank is shown in the instructions.
Compacts if attached directly to the bowl. The design diagram is drawn in the instructions, fasteners are included, so assembly will not be difficult.

bowl design:

with flat flush;
with vertical flush.

The location of the neck of the bowl is front and back. The front is more common, as it is more convenient to use. The toilet diagram in the instructions allows you to decide what exactly is suitable for use.

Preparing for installation

If it is implied, then first needs to be dismantled old equipment and install new equipment in its place. Proper installation of the toilet bowl is the key to cleanliness and safety for a new repair. The seams should not leak, the body should not wobble or make sounds.

If the ceramic tiles have already been changed, then the installation of plumbing is carried out directly over tiles. In this case, you need to carefully use a drill so that the tile does not crack.

If the old plumbing is being removed, and there has not been a repair yet, then before starting the dismantling, you need to prepare rags, because water will flow from the toilet. The bowl must be washed and treated with a disinfectant. You should also turn off the water supply and drain the remains from the tank.

First, all existing hoses are disconnected, screws are unscrewed, and the tank is dismantled. Next, you need to knock out the leg from the tile. For this use a crowbar. The nuts are unscrewed from the base of the bowl.

Before disconnecting from the sewer pipe, you need to make a stopper from rags and immediately plug the pipe so that odors do not enter the house. The assembly of the structure will not take much time, so you can use the new thing in one hour if the room has already been renovated. If you have to lay new tiles, you will have to use an outdoor toilet for some time.

How to assemble a toilet can be seen in the diagram. Step-by-step instructions are attached to each equipment model.

Step-by-step instructions for installing a toilet bowl

How to install a toilet? The first step is to connect the bowl to the sewer. This requires a corrugated hose. A rubber seal is put on the outlet end of the product. The other end is connected to the sewer pipe. First, you need to pull out the gag from the rags.

When the product is already in place, they produce the following operations:

Mark holes on the floor with a marker by inserting a marker into them.
Having moved the bowl away, drill holes according to the marks (the diameter must match the fasteners that come with the plumbing, you need to use special drills that can be used to drill tiles).
The product moves into place and is attached to the floor.
The junction of the product and the floor filled with sealant, another option is to cut a thin rubber gasket in the shape of a leg and place it before fastening.

To connect the tank needed:

fixing bolts - 2 pcs.;
rubber gasket under the drain mechanism.

The installation of the toilet cistern begins with the fastening of the bolts. Next, a gasket is placed, and the tank is put in its place. The holes line up and the fasteners are hand tightened. Toilet assembly completed.

Do-it-yourself toilet replacement ends with a connection to the water supply and sewerage. Installation of toilet bowls with a cistern directly attached does not require fastening, as it is a monoblock.

Features of connection to water supply and sewerage

Installation of the toilet is over, then you need to figure out how to establish a connection to water supply and sewerage. For connection to the pipe there is a flexible hose, at both ends of which there are nuts.

Sealing from the side of the sanitary equipment occurs with the help of rubber gaskets or a special tape.

You can simultaneously put a tap on the pipe so that you can shut off the water entering the tank. In this case, other water intake points will work.

How to install the toilet correctly if the drain is different from the previous equipment? You will have to change the piping to match the new model.

Installing a toilet with an oblique outlet

Floor models come with an oblique, vertical or horizontal drain. Installing a toilet with an oblique outlet is different from the vertical or horizontal method.

To joint did not leak, need:

lubricate the outlet pipe with red lead - oil paint mixed with drying oil;
wind the fiber and then also smear with paint;
fix the pipe in the sewer pipe.

The installation of a toilet with an oblique outlet is carried out if the previous equipment had the same drain.

Installing toilet bowls with an attached cistern

The monoblock lasts a long time, so when buying a model, it is recommended to immediately purchase spare internal parts, since models on the market often change, and after a while they will no longer be produced.

Installation of toilet bowls with a tank directly attached is carried out as follows:

the pipe is connected to the sewer;

The assembly instructions for any model are designed for an ordinary buyer or a beginner, so it will not be difficult. It is necessary to study in detail the stages of work, prepare tools, materials - and you can proceed to the procedure for replacing plumbing equipment.

If you started a major overhaul of the bathroom, or the plumbing is out of order, then you may need to replace the toilet. This process has a number of features that must be taken into account, and the approach to choosing a new toilet must also be correct.

Of course, you can call a plumber from the housing office, or turn to private craftsmen who will provide professional installation. But installing a toilet bowl with your own hands will not only save you money, but also allow you to understand the whole process, which means choosing the most suitable installation option.

In this article, we'll walk you through everything you need to repair your toilet to help you do it yourself.

The first thing to decide: which toilet to choose

Replacing a toilet bowl in its entirety is part of a comprehensive one, so it includes:

selection of a new toilet bowl, taking into account the methods of fastening and draining;
dismantling the old toilet;
repair of the toilet room, including the replacement of pipes, screeds, cladding and other things;
installation and connection of a new toilet bowl.

You should buy a new toilet in advance, and at the same time you need to consider some features that will help you make the right choice.

Floor toilet bowls are divided according to their design into several types. Their differences are based on the shape of the main nodes.

The shape of the outlet drain can be horizontal, vertical or oblique, at an angle of 45 degrees.
The toilet bowl can be visor, dish-shaped or funnel-shaped.
The models also differ in the type of cistern: it can be combined with the base of the toilet bowl or mounted on the wall, and at different heights.
The fixings of the toilet bowl to the floor are different. This can be a variant with two or four fixing points, or a design in which the toilet is installed on special corners attached to the floor.

Tip: choose a toilet based on the type of drain. If you are not going to change the sewer pipe, then take a model with the same type of drain as the old toilet. No adapters will provide a high-quality connection of a toilet bowl with a vertical and direct outlet.

The method of connecting the tank will determine the types of further facing work in the toilet room. For example, if you chose to mount to the wall, then you will need a prepared place and anchors for installation.

First of all, the water supply inside the drain tank is blocked, the water is drained from it and the underwater hose is unscrewed. After that, the tank fasteners are unscrewed. If they are rusted or covered with lime deposits, hold the bolt head with a screwdriver and unscrew the nut with an adjustable wrench. Use kerosene or aerosol lubricant - these products greatly soften rust and lime deposits.
After the tank is removed, unscrew the fasteners that hold the toilet - dowels or nuts screwed onto the anchor.
Now you need to disconnect the drain from the sewer pipe. If your house is still an old building, then most likely the drain will be fixed. In this case, you will need a hammer and chisel. Position the chisel across the paste and carefully prick the cement in two places. Rock the toilet with force so that the drain turns and loosens. Tilt the toilet without removing it so that the remaining water drains out of it.
After the dismantling of the toilet bowl is completed, close the hole in the sewer pipe with a wooden plug or a cloth stopper.

Dismantling the toilet does not require special care, because it is unlikely that you will reuse the product. Therefore, if the cement coating is too strong, you can beat off part of the toilet bowl with a sledgehammer to facilitate work, and then make a transverse hole in the pipe, insert a metal rod there as a lever, so that it is easier to loosen the drain.

For your information: if you have cast iron drain pipes installed in your apartment, it is better to immediately replace them with plastic ones. The operation of PVC pipes is much easier, both for the initial wiring and for connecting all drain points.

DIY toilet installation process

After you have dismantled the old toilet or done all the finishing work, prepare the surface, level it and proceed with the installation of the toilet bowl.

Attach a rigid pipe or corrugated pipe to the toilet drain for articulation with the sewer outlet pipe. The best option would be in which the toilet drain goes directly into the pipe outlet. Use a rubber seal with a border for this. Do not seal the drain transition to the sewer inlet with cement.
Prepare the water inlet. A flexible hose that is wound onto the inlet to the tank and the water supply tap is well suited for this. Pay particular attention to the diameter of the hose fittings at both ends.
After the connection is made, you can fix the toilet on the wall or floor. Below we will look at this process in more detail.
Assemble the toilet. On the base, previously fixed, install the tank. If your tank is suspended, fix it to the wall and run a pipe. Now you can check whether the settings of the tank are correct and the toilet is functional. Turn on cold water, wait for the tank to fill. While the water is being collected, you can adjust its level. You can find out more about this in the instructions for the tank.
The last step is to attach the toilet seat. There are holes on the top of the toilet bowl for mounting it, and the necessary parts are supplied in the kit.

Now we will consider in more detail the methods of attaching the toilet bowl, as well as the features of each of them.

How to properly install the toilet, taking into account any little things

Usually there are three options by which the toilet is attached to the floor:

installation with anchors cast into the screed or dowel;
fixing the toilet with screws on a wooden base, pre-mounted in the screed;
epoxy resin installation.

If you decide to change the toilet due to a major overhaul, then the most suitable option would be an anchor fastening or a prepared wooden base. In this case, the anchors for attaching the toilet bowl are placed on the floor when forming the screed. You should install them so that they protrude 5-6 cm above the surface. The excess can then be cut off.

Match the taffeta (wooden board) to the size of the toilet base. Over its entire surface, hammer nails in a checkerboard pattern so that they protrude on the other side. Now turn the taffeta over and place it where the toilet will be. Fill the screed with concrete along the top edge of the board, install the toilet and secure it carefully with screws.

There are also certain rules for attaching a toilet bowl to a tiled surface. Be sure to wear rubber gaskets under the nuts and dowels: they will not allow the toilet to crack when tightened and prevent rusty drips on ceramics. Use nickel-plated anchors and bolts, they are easy to unwind even after the service life has expired.

Tip: when installing the toilet on, in order to prevent damage to its appearance, use an epoxy mount or dowels.

Under the dowels, you will need to make holes through the screed and tile into which the screws will be screwed. The holes should not be too deep so as not to touch the waterproofing layer. If the screed is too thin, pour some sealant into the hole before installing the dowel. Be sure to put a rubber gasket on the screw. It is best to place the toilet on a cushion of sealant, and then press down with screws.

What other toilet installation options are there?

When installing a toilet, you can completely do without such details as anchors, dowels and screws. Epoxy resin will come to your rescue. The main thing is to prepare the base of the toilet bowl and the floor surface in accordance with all the rules. This option is optimal if the tank is mounted on the wall, since it is he who represents half the weight of the complete structure.

First, go over the surface of the floor with sandpaper or an abrasive stone so that the epoxy resin subsequently grabs and holds well.
Apply the adhesive to the floor and base of the toilet in an even layer of a few millimeters. Install the structure, align it and wait for the resin to dry completely.

Recently, hanging toilets have become popular. They are installed on the wall, without any contact with the floor. For installation, you will need to make a metal frame and attach it to the load-bearing wall, and fix the toilet bowl directly on it if you plan to hide pipes and a tank behind a plasterboard wall.

You can also mount a hanging toilet with an open-type cistern directly to the wall, but in this case, you will need to transfer the sewer pipe into the thickness of the wall. The structure is fixed by using anchors built into the frame or wall.

DIY toilet installation video

Having familiarized yourself with the process of self-assembly of the toilet bowl, you can easily determine how much money you managed to save without involving a plumber or a private master. We are always happy to help you in any endeavors. In the comments, you can leave your questions, comments and examples from your own experience. Comfort to your home!