A palm tree is considered a symbol of summer and relaxation. But most people do not have enough money to visit near a living palm tree. Therefore, you can combine business with pleasure and make such a decoration for your garden as a palm tree from plastic bottles with your own hands.
Original decor
For this we need:
- Plastic bottles 15 pieces of brown color, with a capacity of 2.5 liters - for the barrel;
- Plastic bottles of 10 pieces of green color, with a capacity of 2 liters - for leaves;
- Any wires with a diameter of 12 mm for fastening;
- Metal sheet 0.5 cm thick;
- Two iron rods 25 cm long;
- Metal tubes 20 mm thick.
How to make a palm tree from plastic bottles, we will tell you step by step in an easy master class.
Cut leaves for palm trees. We take a plastic green bottle and cut it into two equal parts. We need the top one.
We cut the upper part of the bottle lengthwise into strips 3 mm thick.
Please note that the shape of the bottle itself is not so important when making a palm tree.
Thus, we make all the green bottles that are available. We fix the prepared parts on the wire and connect them together. Such a preparation should not be alone.
We proceed to the manufacture of the trunk. For this we take brown bottles. We make cuts along the bottles. Most importantly, they must be wide. And cut out the bottom, as shown in the photo.
Next, we carry out welding work. To do this, we take a metal sheet and weld two iron rods to it as follows: the first rod is at an angle of ninety degrees, and the second rod is approximately at an angle of 60-70 degrees.
It is necessary to put metal tubes on the welded rods. The height that you want to make a palm tree.
We weld metal bushings at the end of the rod. They are necessary in order to fix the leaves made there.
We attach the leaves to the metal pipe. It is better to bend them so that it looks more like a palm tree.
The leaves have been collected, now we move on to the trunk itself.
The main points in the manufacture of leaves for palm trees:
- If you want your palm tree to have wide leaves, then for this you must first cut off the bottoms of the bottle. Next, we cut it into three parts. You can use the yellow color of the bottles, or you can use both colors. So the palm tree will be more expressive and bright. The most important thing is to cut almost to the end of the bottle, you can literally leave half a centimeter;
- Using scissors, round the leaves to the base;
- Next, we make a fringe on the cut strips. Thus, we do on both sides of the sheet. The middle of the sheet should be about one and a half centimeters. To make your palm tree more magnificent, you need to bend the fringe with scissors in the following order: one cut up and the second down.
The main points in the manufacture of a palm tree trunk:
- Cut off the bottom of the bottles;
- We retreat half a centimeter from the lid and cut out eight petals;
- We turn each of them in the opposite direction;
- To save material, you can use the cut off part. Only in order to fix it, you have to make a hole in it.
Key points to consider when assembling a palm tree:
As a barrel, it is best to use a metal-plastic pipe. And the best choice of diameter is 20 mm. You choose the height you want.
It is best to collect the palm tree itself from below. The higher the palm, the smaller the details of the trunk should be, that is, it is best to use the largest blanks for the bottom. The method is the simplest and not complicated - a glass in a glass. It would be better if their arrangement is staggered.
The bottom itself is best fixed on glue "Moment" , so it will be most reliable. Approximately 30 cm before the top of the stem, it is necessary to complete the assembly of the stem and continue to fix the leaves. It is also recommended to use a checkerboard pattern.
Once you have collected all the palm, it is necessary to bury the welded reinforcement in the ground to a depth of thirty centimeters. Then we put the finished palm tree on the armature.
table palm
For its manufacture we need:
- Bottles with a capacity of 1.0 liters of brown color - 3 pieces;
- A bottle with a capacity of 0.6 liters of green color - 1 piece;
- Stationery scissors;
- Glue "Moment".
Let's get started, here's a step-by-step guide:
- We cut each of the brown bottles into four parts, it is desirable that they be the same. In each of the parts we make cuts in the form of triangles. The size of which will be approximately one centimeter;
- Carefully bend the resulting triangles;
- We take a green bottle and divide it into three parts. We cut each part in the form of triangles. The part with the neck will be the largest of all;
- We assemble palm trees. We assemble the trunk: first the bottom itself, then all the other parts. When assembling, all parts must be glued. We make the leaves as follows, first insert the largest part with the throat into the trunk, then the middle part, and attach the bottom to the very top.
Palm is ready!
Video on the topic of the article
Often, plastic bottles from various drinks have to be disposed of, but such garbage can decorate any piece of land if you work a little with this material. The original palm tree made from plastic bottles is a perfect confirmation of this. Even for people who are far from creativity, it is not difficult to make it, having the right materials, tools and the desire to put their wonderful idea into practice.
Thanks to new ideas and advanced technologies, a lot of good things come into modern life, making it easier and more attractive. However, innovation also has its downsides. An example of this is a plastic bottle. It appeared in 1941 and became popular all over the world. She was rated for the following positive qualities:
- low cost;
- manufacturability;
- ease of use;
- the possibility of further application.
It is worth noting that there are also negative features in the use of plastic containers, since the plastic from which food packaging is made has not decomposed for more than 100 years, falling into the ground. Often, many people, more often summer residents, accumulate a lot of bottles that require disposal.
In the absence of a centralized garbage disposal in the nearby area, no one wants to litter the soil with plastic waste. Therefore, do not throw away empty plastic bottles. It is better to make an interesting forever green tree out of them, using a tutorial on how to make a palm tree out of plastic bottles.
It will wonderfully decorate and enliven:
- adjacent plot of land;
- playground;
- place near the outdoor pool;
- garden plot;
- plot of land near the outbuilding.
Such a non-standard craft can effectively decorate a wedding, a party, a themed evening, a children's holiday.
What tools and materials are required
Before starting work, you need to collect the required number of plastic bottles with a volume of 1.5-2.5 liters. Green color has a container from under the sprite. Brown bottles are released from beer or kvass. Neighbors and acquaintances can be involved in the process of finding the required number of bottles.
For this workshop on making a palm tree from plastic containers, in addition to green and brown plastic bottles, the following accessories are needed:
Before you make a palm tree out of bottles, you need to decide how tall this tree should be. Its size in height, the splendor of foliage is directly determined by the number of collected bottles. For example, if you make the main palm tree 1.5 m long with a process of 0.5 m, then you will need about 25 brown bottles for the trunk of the future tree and 15 pieces of green for the crown of the plant. When choosing plastic containers, you need to take into account that palm trees with trunks and leaves made from bottles of the same diameter look more beautiful.
When smaller green bottles come across, they can be inserted instead of leaves in the middle of the crown. It is also worth considering that a larger container is used at the base of the palm tree, and a smaller one is closer to the top. As for brown small bottles, they are used for artificial tree trunks of a different size or type. In the event that plastic bottles have different shades, then this is even more interesting, since the manufactured tree will look brighter and more vibrant.
Palm Assembly Step by Step Guide
The above description, indicating all the nuances of creating a palm tree from plastic bottles with your own hands, step by step, in just one evening, will allow you to assemble an unusual beautiful tree of the intended size.
The process can be divided into three steps:
- collection of leaves;
- creation of a plant stem;
- combining all the prepared wood elements and performing the final installation of the palm tree.
There are a fairly large number of various options for how to make a palm tree with your own hands, but in any of the chosen methods, the longest and most lush leaves can be obtained from large bottles, for example, two-liter ones.
First way
Making an original craft with this method is simple. It includes the following steps:
For a palm tree, they dig a small hole, fill it with cement, set its finished palm tree in the center, and fix it with twine for stability. The original plastic tree is ready.
Second: start with the crown
According to this version of the manufacture of a plastic plant, work begins with the creation of its crown. The step by step process is as follows:
At the next stage, the stem part of the plant will be assembled. To make it look like a real tree support, you will need brown bottles with cut off bottoms.
- Along the containers from bottom to top, not reaching 4-5 cm to the neck, cuts are made that divide the container into 6 identical petals.
- Collect the details of the trunk in the same way as the leaves of the future tree. To install a palm tree in a vertical position, you will need a rigid structure such as a metal rod of sufficient length and diameter.
Then proceed to the assembly of the plant. Connect the crown and trunk of a tree. For the purpose of reliable fixation, a piece with holes is welded at the top of the metal rod, through which a rope (wire) with leaves can be passed. Light small leaves are fixed with glue or adhesive tape in such a way that a crown is evenly diverging in all directions.
As a result, the resulting structure will be quite weighty. It will need to be strengthened, using a heavy layer, the base. They can serve as a welded platform or another metal, plastic structure, which is deepened into a prepared hole by 0.5 m, covered with brick chips, earth, followed by compaction of the soil near the tree trunk. The place of plastic landing from above can be concreted.
Third way
This version of the manufacture of an evergreen plant is distinguished by its originality. Algorithm of actions for creating a tree begins with the most complex process - the formation of the trunk:
- for work, you need a third part of the container, which must be cut off from above (from the neck);
- each blank is cut into 8 petals, a little short of the top;
- the petals are folded outward to give them a scaly surface.
In order to reduce the amount of waste, the lower parts of the container can be used for work. To do this, a hole is made at the bottom of the container with a hot knife, through which the parts can be put on a metal rod or other structure for the barrel. The further algorithm of actions for preparing the barrel parts is similar to the previous one. When the blanks are ready, they are sequentially strung on metal fittings.
If the future tree is tall, then it is better to cut the crown from a five-liter container; for a plant of medium height, a container with a volume of 1.5 liters is enough. Leaves can be made in any shape. The wide foliage resembling a fan looks advantageous at the craft. Suitable for containers of green and yellow colors. To make leaves in this shape, you need to perform a few simple steps:
Finished foliage parts are put on a cable or rope. At the end of all work regarding the trunk and crown, all elements of the craft are fastened together.
Fourth: more plastic containers
When making an artificial beauty in this way, the bottoms of the container will be required, that is, many more plastic containers will be required.
The step-by-step process of making a crown is as follows:
- At the bottom of each bottle, a hole is made with a drill or a hot knife, the size of which corresponds to the selected base.
- The resulting green blanks are put on a hard wire (cable).
- Both ends of the wire are fixed with caps that prevent the parts of the crown from moving out.
A log is used as a trunk, the diameter of which is suitable for the future tree. Then this trunk is completely upholstered with the bottoms of brown bottles overlapped with nails. The result is a very beautiful palm tree.
Indoor palm
You can make a decorative small palm tree from plastic bottles. How to do it is not difficult. You will only need three brown bottles for the trunk and one green bottle for foliage with a volume of 0.6 liters.
Each brown bottle is cut across into 4 parts. Triangular cuts 1 cm in size are made on each side of such a cut. Bend these triangles. Then you need to divide the green bottle into three parts. Of these, the largest (9 cm) will be with a neck.
The trunk should start from the part with the bottom. The remaining components of the trunk are glued into it. Glue is better to use universal. It is devoid of an unpleasant odor and interacts well with plastic. Such a palm tree can be placed in the room.
At the end of the workflow, you get a delightful exotic palm tree made from plastic bottles, created by yourself. This evergreen plant will serve as a decor for the selected piece of land, create a warm tropical atmosphere, and will delight others with eternal greenery and a beautiful unusual view for a long time.
Today, the owners of cottages and household plots are trying in every possible way to decorate the exterior. There can be many ways, starting with landscaping and ending with some kind of buildings. One of the most budget options can be called from plastic bottles. In this article, we will tell you how to make a palm tree for your backyard from plastic bottles.
Materials for palm trees from bottles:
- green and brown plastic bottles;
- scissors;
- Metal sheet;
- metal rods;
- metal bushings and tubes;
- high voltage cable.
1. Prepare the bottles in advance and clean them from the labels. Start by making palm leaves from green bottles. To do this, cut the bottle in half.
2. Cut the strips on the top of the bottle lengthwise but not all the way through.
4. For one palm tree, you will need 7 palm leaves, the length of which you can adjust yourself.
5. To make a barrel, take brown bottles and cut wide strips on them. You should get 6 wide strips along the entire bottle of 2.5 liters.
6. Also string blanks for the barrel onto a high-voltage metal cable.
7. Start preparing the base for the palm tree.
9. Take tubes with a diameter of 2 cm, put them on the rods. Weld metal bushings onto the end of the rod so that later palm leaves can be passed through them.
11. Start assembling the barrel from the bottom up.
12. After the entire palm structure is assembled, bury it in the ground to a depth of 0.5 m.
Do-it-yourself palm tree from plastic bottles ready, now you can create a whole piece of paradise in your backyard. Do not be afraid to fantasize, palm trees can be of any size, and instead of coconuts, attach bright plastic bottles for juice or sweet water.
You can come up with your own scheme palm trees from plastic bottles.
The first plastic bottle was developed in 1941, and today it is used not only for household purposes and for storing water, but also as a convenient and inexpensive material for drinking.
With original crafts made from plastic bottles, you can easily decorate your site! Such material is quite durable and easy to process, thanks to which a wide variety of products are created.
For example, you can create a wonderful palm tree from plastic bottles with your own hands! Such an evergreen palm tree will decorate your site or, for example, a playground all year round.
This master class will help you make such a craft!
You will need materials and tools such as:
- plastic bottles of brown and green;
- scissors;
- stationery knife;
- thick wire for the frame.
To begin with, it is worth deciding how high the palm tree will be. In this case, the palm tree will be approximately 1.5 meters high, and the second one will be 50 cm. For this, you need about 23-25 bottles of brown shade per trunk and 15 bottles of green shade for the crown!
To create a barrel, brown bottles need to be cut in half as in the photo below.
We need bottles of different sizes, those that are larger to use at the base, and smaller ones, at the top of the trunk. Bottle caps must be removed. You will need both the top of the bottle and the bottom.
Then, the edges of the blanks are cut out in the form of petals, about 6 “petals” should be obtained.
After, they need to be bent.
It should turn out like this.
In the future, they will fold into each other. Since there is no hole for the wire at the bottom of the bottle, it must be made using a hot nail, a knife, or it can also be drilled. Having folded the blanks, you get a rather fluffy trunk of a palm tree.
After all the details on the palm tree trunk are ready, you need to start creating palm leaves!
Bottles can be used in different shades of green. You can also experiment with the volume of containers, for example, use two-liter containers at the base, and arrange smaller ones at the top. To do this, on green bottles you need to cut off the neck and bottom.
Then, cut the bottle into three pieces.
If you want wider leaves, you can cut it only into two parts. You will get such a preparation.
After, the strips need to be straightened in different directions.
This will give some splendor to the crown!
Now, the simplest and final stage in creating a palm tree from plastic containers remains!
After all the details are ready, you need to securely install the frame of wire or other suitable material in the desired location on the site. And then, string on the frame all the received parts of the palm tree.
Using a large cork from a five-liter bottle, make a retainer on top to securely fasten the leaves. To do this, in the center of the cork, you need to make a hole, a slightly smaller diameter than the frame.
Then, after the crown is fully assembled, put it on the wire!
That's all, it turned out to be a very original palm tree that can be installed on the site or on the playground!
The final look of the craft. Photo 1.
The final look of the craft. Photo 2.
Such a craft, of course, will decorate the area, as well as give a positive mood to the kids, including, like a plastic basket made by yourself!
Step-by-step instructions for beginners on how to make a palm tree from plastic bottles with their own hands are necessary for the owners of suburban areas, regardless of whether there is a sea nearby or not. A self-made craft will decorate the site and guarantee an exotic design solution. The article provides instructions on what types of palms are allowed to be performed and how such a process is performed.
How to make a palm tree from bottles with your own hands: step by step instructions
Before studying the scheme of action, you should figure out how many empty containers will be required to complete the work. The optimal amount is 10-15 pieces of brown plastic.
This can be two-liter and one and a half liter bottles. It all depends on the size of the future design. For "leaves" you need to prepare containers and containers larger in size. These should be green items in the amount of 7-9 pieces. Having prepared the required number of containers, a person must perform step-by-step actions:
- A trunk is being made, for which a brown bottle and a knife are taken.
- The cork is removed and the plastic is cut across. The bottom should be larger than the top.
- Part of the taken container is cut into 6 parts. Reaching the narrow part, you need to stop the operation. It is important to give each element the shape of an ordinary oblong triangle or attractive petals. It is required to round and slightly narrow the pre-cut elements.
- A similar procedure is carried out with all prepared parts. After a hot awl, a hole is made equal to the diameter of the bottle.
- A fold is made at the base. Next, all the resulting petals are bent.
- Decorated halves should be inserted into each other, neck down. A metal rod is pushed through the entire length. The bottom is attached with tape.
After completing this section, it is important to proceed to the foliage. For this purpose, green blanks are taken. When deciding how to make a palm tree from plastic bottles, the following step-by-step instructions are performed:
- Corks are removed from the bottles and the neck with the bottom is cut off;
- The workpiece is cut into three to five parts, strictly, without reaching the top;
- Details open to leave a hole in the center for attaching greenery;
- The foliage is brought to its natural form, for which it is necessary to make cuts on the petals to the middle;
- The leaves are rounded and oblique cuts are made;
- The resulting thin strips are folded to the side to give a curvaceous look.
The number of green elements can be any. The larger it is, the more magnificent the tree will be. The resulting greenery is put on the stem pin.
When attaching it, it is advisable to use a checkerboard pattern. This will prevent unnecessary gaps from appearing. The end piece is secured with tape. The finished craft must be firmly fixed in a pre-selected place by digging in the bottom of the rod.
Necessary materials
In order for the operation to perform an artificial tree to avoid problems and delays, you need to prepare the materials in advance:
- Required number of containers.
- Scotch.
- Awl.
- Scissors.
- Metal rod.
If you prepare the required tools, you can get a garden product that will effectively decorate the site. This is a great way to give yourself aesthetic pleasure. 
Instruction for beginners
If there is no experience in doing crafts with your own hands, if there is a lack of self-confidence, before making a large tree, you can create a small one. 
Here you need to take only three blanks of a brown shade and one green. To get a small product, you should study the video for beginners or a special master class and perform such operations.
