Suspensionless gable roof truss system. Step-by-step installation of a gable roof - a guide to the home master. Rafter system of a broken gable roof

The construction of a truss system is a rather complicated and responsible business. However, it can be done independently if you follow certain rules.

This article will talk about the elements of the roof structure, as well as how to put the rafters on the roof.

Before you put the rafters on a gable roof, you need to find out what elements the roof structure consists of. It consists of:

• Mauerlat. This is a beam rigidly fixed along the load-bearing walls of the building. For its manufacture, as a rule, a bar with a section of 15 by 15 centimeters is used. serves as the bottom, and also evenly distributes the load created by the roof structure on the walls of the building. Between the bearing wall and the Mauerlat beam, a waterproofing material, for example, roofing material, should be placed. If the roof frame is made of metal, channels or I-beams are used as Mauerlat.

• Rafter legs. They are the main element of the roof frame. Their size is taken in accordance with the design calculations. The lower parts rest on the Mauerlat beam, and the upper parts on the ridge beam. For their manufacture, regardless of the type of construction being erected, it is recommended to use a pine board with a section of 150 by 50 mm or 200 by 50 millimeters.

• Run. It is a horizontally located beam that perpendicularly crosses the rafter legs along the entire length of the roof. There are three types of runs in the truss structure: side, ridge and Mauerlat.

• Sill. It is a horizontal bar that is mounted on an internal load-bearing wall. This element serves as a support for the racks and evenly distributes the load they create. Beds install complex truss systems. In other words, this roof element is optional and is applied where necessary.

• Puff. It is an element of a hanging rafter system. The puff forms a triangular truss with rafter legs. This element reduces the expansion force created by the hanging rafters on the walls of the building. The location of the tightening depends on the type of roof structure being erected.

• Rigel. This element, like the puff, connects the rafters. The crossbar makes the structure more durable and stable. For its manufacture, a bar with a section of 10 by 15 centimeters is usually used. On the crossbar, in contrast to the tightening, there is a compressive load, and not a tensile one.

• Racks. It is a bar installed vertically. It is used if the width of the building is large enough. This element strengthens the truss system from the inside. Runs supported by struts are installed on the racks.

• Struts. They are inclined beams supporting horizontal elements. Struts reinforce the structure of the truss and counteract the distortion and compression of the roof structure.

• Roof overhang. This is part of the rafter legs protruding from the outer walls of the building by about 40 centimeters. The overhang protects the outer walls of the building from rain and melt water rolling down from the roof.

• Filly. It is a piece of board. Used to lengthen the lower part of the rafter leg.

Tools and materials

The roof structure should be made of coniferous wood. The moisture content of the wood used should be less than two percent. Before use, the material must be treated with special protective equipment.

For the manufacture of hanging rafters and puffs, they are made from first grade wood. Rafter legs are made of wood of the first and second grade. It is possible to use a tree of the third grade only for the manufacture of struts and racks.

The strength of the roof structure depends on:

• Reliability of connections;

• The quality of the material used;

• Correctness of the performed calculations.

Before you put the rafters on the roof, you need to prepare the following tools and materials:

• Axe;

• A hammer;

• Level;

• fasteners;

• waterproofing material;

• boards;

• Pencil;

• Chainsaw;

• Electric drill;

• A set of drills for an electric drill;

• Nails or screws;

• Roulette;

• Cord.

For the manufacture of stopels, a bar or edged board is used. Wood elements should be treated with bio-protective and fire-retardant materials.

Before installation, it is necessary to choose the type of ridge connection and the method of fixing the rafters to the beams or mauerlat.

Calculation of the pitch of the rafters

This issue must be given special attention, because the strength of the roofing system depends on their cross section.

When calculating the distance between the rafters, the permanent and temporary loads on the roof being erected should be taken into account. The following elements create a constant load:

• roofing material;

• rafter system;

• roofing pie (vapor barrier, insulation, waterproofing);

• elements of decoration of the attic or residential attic.

• the weight of a worker performing roof repairs or maintenance.

To perform calculations (section and step of the rafter legs), theoretical knowledge is required, as well as practical skills. You can determine the approximate parameters of the roof structure using the following table:

When choosing a rafter pitch, it is necessary to take into account the type of heat-insulating material. It is important to remember that the span between adjacent rafters should be 10 - 15 millimeters less than the width of the cotton insulation.

Also, when choosing the distance between the rafters, it is necessary to take into account the recommendations for laying the selected roofing material.

Types of truss system

There are two types of rafters: hanging and layered. Each type will be considered separately.

hanging

Hanging truss systems are used in cases where there are no internal supports (columns, walls) in the house. This design is supported by external retaining walls.

In this case, the rafters work in compression and bending. exert a bursting force on the outer walls of the house. To reduce it, use a puff.

The puff is made of a wooden bar or metal. Its location depends on the design of the roof being built.

For example, when erecting a mansard-type roof, the puff is placed at the base. In this case, it performs the functions of a floor beam. The higher the puff is located, the greater the load on it.

A hanging truss structure is used if the distance between the supports is less than 6.5 meters. For the manufacture of these rafters, boards, logs, or timber are used. To connect elements to each other, use:

• steel profiles;

• cuts;

• bolts;

• nails;

• pins.

Rafters

Rafters of this type are used in buildings with a solid internal wall. These elements are usually made of wood.

The internal elements (column, wall) serve as a support for the layered truss system. This is their main difference from the rafters of the layered type.

Rafters of this type work only for bending. Laminated truss structures, in comparison with hanging ones, are more cost-effective and lighter.

How to put rafters on the roof

Installation of gable roof rafters consists of the following steps:

1. Making a truss truss template. It is necessary to raise two boards to the ceiling, and then connect them together from one edge with nails. Next, you need to install the free ends of the boards on the support beam and fix the angle between the boards. To do this, you need to nail the transverse jumper. Then you need to lower the resulting template onto the support beam and mark the angle of trimming the rafter legs with a pencil. It should be noted that the strength and reliability of the entire roof structure will depend on the quality of the template made.
2. Lower the made template down and start making rafters. The template must be well fastened so that when it is lowered, the angle between the rafters is not disturbed. The first manufactured truss truss is lifted onto the building and installed on the base.
3. Mark the cut point on the Mauerlat and rafter legs and cut with a chainsaw. Next, you need to start assembling the next truss truss.
4. Install the first two roof trusses on the Mauerlat beam along the edges of the building. The rafters installed along the edge of the Mauerlat beam are fixed on both sides with the help of props. Then pull a cord between them to determine the level. Rafter trusses must be installed perpendicular to the base of the ceiling.
5. It is necessary to assemble the remaining roof trusses after the level is set and all fasteners are checked. The rafters will not move if two boards are hammered between them. Next, you need to fix the cross bars and supports.
6. Perform installation of a vapor barrier, heat-insulating and waterproofing layer. Roofing material is attached to the crate. Its step depends on the chosen material for the roof.

This video shows how to put the rafters on the roof:

During the construction of private houses, the roof is most often made gable. There are reasons for this. First, it is reliable. Handles wind and snow loads well. The second - it is compatible with any roofing. The third is relatively inexpensive. The fourth is a simple design that is difficult to spoil. Fifth - it looks attractive. All this, and also the fact that a do-it-yourself gable roof is built without special knowledge, determines its popularity.

Do-it-yourself assembled gable roof ready for installation of roofing

Step-by-step installation of a gable roof

As you saw above, there are a lot of truss systems. Accordingly, when assembling each has its own characteristics, but in general the order is the same. It is necessary to say about the general step: pre-drying and processing of wood. This step is required if you bought fresh lumber, not dried.

The use of raw wood of natural moisture in the construction of the roof will lead to problems: the beams will bend, they will dry out, the geometry will change. All this will lead to the emergence of stress points and at the slightest sign of overload (a lot of snow, strong wind or rain), negative processes will begin. Their elimination is a complex and costly undertaking. Therefore, either buy dry wood (no more than 20%, ideally chamber drying 8-12%), or buy material a couple of months in advance, put it in ventilated piles. After that, treat with the necessary impregnations (from fungal attack and to reduce flammability) and only after that use it in the installation of the truss system.

Timber must be dried in ventilated stacks. To do this, they are laid in short pieces of boards. They are placed a meter from the edges and further through the meter. Spacers must be installed under the bottom

We will talk about the main stages of assembly, about how to make a gable roof with your own hands in this section.

Mauerlat

The assembly of the gable roof truss system begins with the installation of the Mauerlat. It must be set strictly horizontally, therefore, before starting installation, the horizontalness of the wall to which it is attached is carefully checked, if necessary, it is leveled with cement mortar. You can continue work after the solution gains 50% strength.

Depending on the system, this is a beam with a section of 150 * 150 mm or a board with dimensions of 50 * 150 mm. It is attached to the top row of masonry walls. If the house is wooden, its role is played by the upper crown. If the walls are made of light building blocks - foam concrete or aerated concrete and others - their rigidity is not enough to redistribute the load. In this case, a reinforced concrete belt is made over the last row of masonry, into which embedded fasteners are embedded - wire or studs. A bar or board is then mounted on them.

There are several ways to connect walls and Mauerlat:

• In the masonry (in the reinforced concrete belt) a smooth rolled wire of large diameter is fixed (two ends stick up). Holes are then made in the board in the necessary places, into which the wire is threaded. She then twists and bends.
• Studs with a diameter of at least 12 mm are immured in the wall. Under them, holes are made in the Mauerlat, a beam / board is placed) and tightened with nuts with wide washers.
• Aligning the beam or board along the outer or inner edge of the wall, take a drill with a diameter of 12 mm, make holes for the anchor bolts. They (the same diameter of 12 mm) are hammered to the very hat, then tightened with a key.

The distance between the studs (wire) should not be more than 120 cm. Cut-off waterproofing must be laid on the wall (belt) under the Mauerlat. It can be rolled roofing felt or waterproofing in two layers, it can be smeared with bituminous mastic.

Rafter installation

There are more than a dozen types of gable roof truss systems. First of all, you need to choose what yours will look like. Further, in order to make it easier to work, a template is made from thin boards for all cuts, cuts and other similar details. To do this, you may need to assemble the first form on the roof, and then make templates for the finished one.

The assembly order depends on the type of truss system. If the rafters are layered, they are installed gradually, assembling from the elements directly on the roof. In this case, it is convenient if the beams of the ceiling are laid and, if possible, the draft flooring of the attic or attic.

In systems with hanging rafters, a farm is assembled on the ground - a ready-made triangle of puffs and rafter legs with all the required struts, racks. The required number of farms is assembled at once. Then they are lifted to the roof, placed vertically there and attached to the Mauerlat.

On the one hand, this is convenient - it is easier to work on the ground, with a high assembly speed, the accuracy is high: one farm is not much different from the other, which simplifies the procedure. But it can be difficult to raise finished trusses, especially for large buildings. To make this easier, two inclined boards are installed, which at one end rest against the ground, and the other sticks out a little above the wall. Farms are brought closer to this “lift”, one by one they are installed below, ropes are tied and pulled along the boards to the roof. In the absence of a winch or crane, this is the most acceptable method.

The assembly of rafters requires certain knowledge: how and in what order to mount them, how to mark and make cuts. See the video for the assembly of one of the schemes with a headstock.

Assembly order of the truss system

Everything, the do-it-yourself gable roof is assembled and ready for installation of roofing material.

The process of installing the rafters itself raises enough questions, but there are many ways and it is impossible to tell about them all. See one of them in the video. The system is large and went up to the roof in parts, and there it was already assembled into a single structure. It is convenient for large houses.

Features of the installation of the truss system of a wooden house

The difference between wooden houses is that the log house shrinks, and this leads to a change in the geometry of the truss system. If the elements are fixed rigidly, the roof may fall apart. Therefore, the mounts are made floating. There are special sliding fasteners, which in this case attach the rafters to the upper crown and to the girders, if any (see photo).

In order for the rafter to move freely during shrinkage, its long part is fixed strictly parallel to its edge, and the support is placed strictly perpendicular. If necessary, a platform is cut out under it. Mark the mount so that the hook is in the lowest position or near it. They are mounted on special self-tapping screws that come with the kit (ordinary ones do not fit). If the installation is done on a log, so that the rafter leg does not slip along it, a semicircular hole is cut out in the lower part, on which it will rest.

Such fasteners are sold on any construction market, it is called "slippery". How to attach the slippery to the beam, see the video.

Video on assembling and installing a gable roof truss system

It is not easy to build a gable roof with your own hands: there are a lot of subtleties and nuances, there are different ways of fastening, building up. Describing them in words is a thankless task. This is the case when it is better to see. Below is a selection of videos that you might find useful.

Video report on how a gable roof is made

The story of the owner of the house about the stages of construction. There are interesting technical points that may be useful.

Two types of rafter connection: rigid and sliding

Video about the two most problematic types of connections.

How to determine the angle of the rafters

Full video report on the assembly of the truss system

This movie is just under an hour long, but the entire process is shown from start to finish with plenty of detail. The roof is placed on, but when installed on buildings of a different type (except for wooden houses), there is no difference.

A roof with two slopes is the most common option for completing the box of a private house. In its manufacture, it is important to correctly select the cross-sections of the supporting elements, securely fasten the nodes and choose the right type of construction. The truss system of a gable roof does not have great difficulties and may well be made by hand.

Classification of truss systems according to the method of support

The structure can be classified in two ways. The first of them is the method of supporting the bearing elements. The gable roof truss system of the house in this case includes the following types:

• with layered rafters;
• with hanging rafters.

Types of a gable roof with layered and hanging rafters

Roofing with the use of layered rafters involves their support at two points. The design in this case avoids the occurrence of a serious spacer. To do the installation yourself, you will need the following basic elements:

• rafter legs;
• Mauerlat;
• crossbar;
• intermediate racks and struts with a large span of load-bearing beams;
• crate and counter-crate;
• overlays persistent bars.

At the top point, the installation provides for leaning on the crossbar. The installation also provides support at the lowest point - Mauerlat. You can assemble such a structure for a house with your own hands only in two cases:

Options for assembling a layered gable roof system

1. A layered system is possible if the distance between the gables is not large. That is, such an installation is suitable for a small house with your own hands. The greatest length of the structure, which allows the construction of a wooden crossbar without additional reinforcements, is 6 m. For large spans, it will be necessary to install metal beams as a crossbar. When using a wooden beam, it will be necessary to provide intermediate racks, which are located on average every 2 meters. This can be avoided only when using glued laminated timber of a sufficiently large cross section as a crossbar. In this case, a free layout of the space becomes impossible - the racks in the middle of the room cannot be removed.
2. The second option, when it is possible to install a layered gable roof system with your own hands, is the presence of a wall in the middle of the house. The device in this case provides that the beam, on which the rafters will rest at the top point, will transfer the load to the inner wall. In this case, the supporting structure should not be confused with the partition. The partition rests on the floors, and installing the wall of the house with your own hands involves resting it directly on the foundations. Such a device is suitable for buildings with sufficient width, where it makes sense to install a wall fence in the middle.

The second option is hanging rafters. They are more complex in calculation, but they allow the installation in the under-roof space of a free-plan house. The design assumes the absence of a supporting wooden or metal bar in the upper part. Installation involves supporting the rafters only at the lowest point. In the upper part, the bearing beams are securely connected to each other. Installing such a system is like a farm. The design works on thrust, so it is important to prevent excessive horizontal load on the walls of the house. You can do this by doing the following:

• the device of a monolithic belt along the edge of the walls;
• it is necessary to make a reliable fastening of the Mauerlat of a gable roof to the wall of the house with your own hands;
• to eliminate the spacer, a contraction is established.

Installation of a hanging truss system

The fight or screed becomes one of the significant elements of the gable roof of the house. It prevents the expansion of the walls under the action of thrust. The following types of fights can be distinguished:

• located at the attic floor level;
• located at the level of the attic ceiling.

It is worth noting that the second option provides less reliability, since the higher the element is mounted, the stronger the rafters have an effect on it. If the fight turns out to be too long, you need to make it stronger with your own hands. For this, additional elements of the gable roof of the house are installed - suspensions. They connect the skate to the middle of the puff, which prevents it from sagging.

The gable roof truss system with hanging rafters allows installation with pre-assembly of trusses on the ground, then raise them to the roof and fix them.

This option is only suitable if you have lifting equipment, since the finished gable roofs of the house will become too large and heavy to lift with your own hands.

Classification by type of slope

The second division can be made depending on how the ramp line is designed. The views here suggest the presence of two options:

Gable roof with broken and straight slopes

1. With straight slopes. The easiest way to do. Allows you to get the job done without any hassle. The disadvantage of this do-it-yourself roofing option is the reduction in attic space.
2. With broken slopes. Such types of roofing are more difficult to perform. It is assumed that there is a line along which the angle of inclination changes. The angle of inclination of the lower part of the slope must be made greater than that of the upper. Thus, it turns out to raise the ceiling of the attic and increase the free space. The installation of the roof is carried out with the installation of an additional crossbar at the fracture site.

These types involve a choice between them, depending on the wishes of the future owner of the building.

The main elements of the roof

The rafter system of the gable final part of the building consists of many elements. Installation should begin with a detailed study of each of them and the choice of their sections.

When installing elements under a metal tile or other coating, it implies the use of a bar with a section of 150x150 or 200x200 mm. It is this size that allows you to most optimally distribute the load. then you need to choose a method of fixing it depends on the material of the walls. There are several options:

The scheme of fastening the Mauerlat to the wall

1. Frame, timber or log walls do not require the installation of a Mauerlat. In the case of a frame building, the top framing of the walls serves as a support for the rafter legs. during the construction of fences from timber or logs, the upper crown becomes the Mauerlat. It is important to correctly fix these elements in the wall structure.
2. When used for the construction of lightweight concrete, additional reinforcement will be required. Lightweight concretes include materials such as foam concrete, cinder concrete, expanded clay concrete. They can collapse if the roof is not supported centrally on them. To evenly distribute the load, a monolithic reinforced concrete belt is poured along the edge of the walls. During work, a special wire, studs or bolts are laid in it, on which the Mauerlat will be fastened.
3. For brick means, it is possible not to provide a reinforced concrete belt. In this case, to connect with the strapping beam, a wire is inserted into the masonry, which is then wrapped around the Mauerlat and twisted. The second option - one row before the walls are cut, wooden blocks impregnated with an antiseptic are brought into the masonry from the outside. Such plugs and Mauerlat are fastened with staples. It is also possible to use studs and bolts, for fixing which will require pouring a monolithic belt.

An important point is waterproofing.

When installing, it is important to provide roofing material, linokrom or waterproofing at the junction of concrete or brick with wood. This is required to prevent the wood from rotting on contact with material of a different moisture content.

After fixing the Mauerlat, rafter legs are installed. Their cross section is selected depending on the pitch of the supporting beams, their span, snow load and type of coating. When installing a frame under a metal tile with a step of 60 cm, it is recommended to follow the following recommendations, depending on the span:

• 3 m - 4x15 cm;
• 4 m - 5=15 cm;
• 5 m - 5x17.5 cm;
• 6 m - 5x20 cm.

Table of average values ​​of rafter legs

These are average values, in order to perform a more accurate calculation, it is better to contact a specialist or study additional literature.

There are two ways to fasten the rafter legs to the Mauerlat:

• with a notch;
• without her.

Fastening rafter legs to the Mauerlat with and without a notch

In the first case, they washed down on the strapping beam, in the second, a special plank is nailed to the rafters, which becomes a persistent bar. Further, for both methods, the work is performed in the same way. With the help of metal corners, the inclined beam is fixed so that it does not move relative to the design position along the Mauerlat. Additionally, nails are driven in at an angle.

Scheme of fastening rafters with wire and brackets

In addition, you will need to fasten the rafter to the wall. The implementation of this measure is provided for in the regulatory documents. You can do this in two ways:

• on brackets (suitable for wooden buildings);
• using wire twisting (a more time-consuming option, but the only one possible for stone houses).

You can perform fastening according to the norms through one leg. This is necessary for a more secure attachment of the roof to the box of the house.

If you do the work correctly, you can not worry about its condition even in the strongest winds.

Racks, ties, struts

Such elements are most often made of boards. The optimal thickness is in the range of 32-50 mm. Racks are an exception. Here you can use boards with a thickness of 50-100 mm. Fastening is carried out on studs or using support bars.

Gable roof truss system: design and nodes

A gable roof is the most common in construction. For proper installation, it is recommended to study the device of the gable roof truss system.

The device of the truss system of a gable roof

The gable roof truss system is designed for roofing in the form of two rectangles located at a certain angle to each other in the upper part of the structure. This design is often used in the construction of private low-rise buildings, various buildings for domestic and household purposes. At industrial and commercial enterprises, a gable roof is installed on buildings for various purposes, which have a significant length several times greater than the width. The design contains two slopes of different lengths. On the front side, a short slope with a large angle of inclination is installed, on the back - a long one, with a smaller angle of inclination. This configuration allows the main part of atmospheric precipitation to be directed to the non-working zone of the enterprise territory.

Figure 1. Scheme of fillies.

The construction of a gable roof is one of the low-cost options that does not require significant physical effort.

It is performed relatively simply with little experience working with wood material.

Typical bearing elements of the system, specific terms

Figure 2. Scheme of the crate.

In the manufacture of details of the gable roof truss system, softwood lumber is used. Hardwood is undesirable due to its high specific gravity. Most of the elements have specific names that are understood mainly by specialists:

1. Lezhen - timber with a section of 150x150 mm, 180x180 mm. It is laid on the surface of the internal load-bearing wall. Designed for leveling the surface and distributing loads from racks.
2. The rafter leg, or rafter, is a piece of timber or thick board. The main element of the triangular roof structure, bearing the main load from snow, rain, wind and other atmospheric phenomena. The distance between the rafter legs can be from 0.6 to 1.2 m. The step size mainly depends on the plumb line of the roofing material, in some cases, the characteristics of the roofing material should be taken into account.
3. Mauerlat - a square beam with a side size of 150-180 cm. It is laid on the surface of external load-bearing walls. When installing, it must be fixed with anchor bolts or in another reliable way. Distributes the load from the rafter legs to the load-bearing walls.

All parts of a gable roof are interconnected in various ways. Previously, structures were assembled mainly using staples, nails, threaded studs. Now manufacturers of building materials offer a wide range of different brackets for assembling roofs of any configuration. Most parts are fastened with self-tapping screws of the required diameter and length, reinforced with special spikes in the brackets.

Additional elements of the rafter system

Figure 3. Scheme of an arch with three hinges.

In addition to load-bearing parts, additional reinforcing elements are used in the structures:

1. Filly (Fig. 1) - used to increase the length of the rafter legs. Are established in the lower part for the device of cornice overhang. The thickness of the filly is somewhat less than the size of the rafters.
2. Roof overhang, or cornice overhang, is a roof element protruding from the edge of the wall by about 40-50 cm. Designed to protect walls from atmospheric precipitation.
3. The ridge is an element that connects all the rafter legs of the system in the upper part. Installed in a horizontal position.
4. Sheathing (Fig. 2) - boards or bars installed for fixing the roof. They are located perpendicular to the rafter legs, additionally performing the function of their fastening. They take the main effort from the roofing material, distribute it to the rafters. For the device, it is desirable to use edged lumber. With limited funds, you can use unedged, clearing it of bark. If the roof is made of soft material, the crate is made solid. This option can be made from boards or plywood treated with protective materials from high humidity. When corrugated board is used, the crate is performed with a certain step, depending on the weight of the material and its design features.
5. Struts - elements made of timber or thick boards that reinforce the main structure. Distribute the force from the rafter legs to the bearing parts. The assembled structure of struts and puffs was called a farm - an enlarged part with the necessary margin of safety.
6. Racks - are made from pieces of lumber of rectangular or square section. Are established in vertical position under a descent of slopes. The load from the corner connection of the roof rafters is distributed through the posts to the internal load-bearing wall.
7. Puff - a bar or board that fastens the rafters in a hanging system. Creates a rigid triangle shape between rafter legs, compensating for sprawl.

For the manufacture of additional parts, you can use lumber with a section similar to that of load-bearing parts. In order to save money, you can calculate and purchase products of a smaller section.

Two typical ways to arrange truss systems

Figure 4. Scheme of connecting the lower ends of the parts.

The gable roof truss system can be arranged in two main ways:

• hanging truss system;
• layered system.

The hanging system is used for buildings with a distance between the outer walls of less than 10 m, without an internal load-bearing wall in the middle of the building. In a different configuration of the building, a layered rafter structure is used.

If the building has columns located along one of the central axes, it is possible to use a combined option. Rafter legs located above the columns are mounted with emphasis on the surface of the columns, hanging rafters are installed between them.

Hanging truss system

In structures of this type, the installation of truss beams is carried out on the surface of the outer walls. The disadvantage of this method is the occurrence of force, bursting the walls. To compensate for the load, the beams are pulled together by tightening. The design takes the form of a rigid triangle that retains its shape under the influence of loads. In some cases, floor beams can play the role of puffs. Such a scheme is used when arranging an attic in the attic space.

Hanging rafters can be made in various versions:

Scheme of the reinforced structure.

1. A simple version of the arch with three hinges (Fig. 3) - the design is a rigid triangle, the two sides of which are the rafter legs. The main load creates a bending force on the parts. The force on the third side is aimed at stretching the structure, so instead of a wooden part, a steel tie can be used. The connection of the lower ends of the parts can be assembled in various ways (Fig. 4), by inserting beams into a puff, using wooden elements or metal brackets.
2. Reinforced structure (Fig. 5) - a gable truss system used for roofing of large industrial buildings with a distance between walls of more than 6 m. This system is not suitable for use in small residential buildings. A design feature is the distribution of the puff weight on the skate. Since it is almost impossible to find solid lumber of the required length (6 m or more), the puff is made from segments. The connection of all elements is carried out by a straight or oblique inset. The central part is called the headstock. The connection of the headstock with a tightening is performed by a collet twist with the possibility of adjusting the tension.
3. The device of an arch with a tightening in the upper part of the rafters (Fig. 6) is used for equipment in the attic space of the attic. At the same time, the tensile force in the rafter beams increases. The lower ends of the beams are attached to the Mauerlat bars. The fastening should limit the movement of the beams to the sides along the beam, but allow sliding across. This ensures uniform load distribution and stability of the entire system. Rafter beams should form an overhang.

Many variants of hanging-type systems have been developed. Most are used for relatively small buildings without load-bearing structures inside buildings. For larger buildings, a layered rafter system should be used.

Layered truss system

The main difference of this system is the installation of a vertical beam resting on an internal load-bearing wall located in the middle of the building. This design is necessary when a gable roof is installed on a building with a wall spacing of more than 10 m.

Figure 6. Arrangement of an arch with a puff at the top of the rafters.

1. A properly executed system of non-expanding rafter beams allows you to get rid of the forces that burst the walls. The surface of the slopes is subjected only to the bending force. There are 3 main options for the device of such systems. With all options, the lower ends of the rafters are attached according to the sliding support method. For insurance, an additional mount is installed between the support bar and the rafter leg.
2. You can use a steel strip, wire tie. The options differ in the method of connecting the upper ends of the rafters, docking with the ridge beam. One of the options involves laying rafters on a beam in the form of a sliding support with a cutout device. Mounting can be done using brackets or special brackets. The gable roof, arranged according to the following option, is the most popular because of the simplicity of the device. The top of the rafters can be made end-to-end or overlay with cutting grooves. The corner must be fastened in any of the available ways and fixed on the ridge beam. The third option involves a rigid connection of the run and rafters. For mounting on rafter legs, pieces of boards are stuffed on two sides. A large bending force is formed on the beam, but the load on the rafter beams is reduced.
3. A gable roof for a building with dimensions up to 14 m must have a reinforced truss system. One of the options for increasing strength is the installation of a strut. The part takes on the load from the rafter leg, experiencing a compressive force. To correctly select the installation position of the element, you need to measure the angle of 45-53 ° from the horizontal plane of the building. An additional support device turns an ordinary beam into a reinforced version, consisting of two spans. To install the struts, calculations are not required, you just need to fix it under the rafter, cutting out the joint angle with maximum accuracy.

The technology for installing gable roofs is simple, you can do everything yourself. Work must begin with the installation and fastening of the base to the walls, then mount the gables. It is desirable to carry out work on the manufacture of rafter beams and enlargement of structures on the ground, to lift the assembled elements, install them on the building, and fix them with temporary fasteners. After assembling and installing all the elements, you should fix the crate and proceed with the installation of the roof.

Gable roof truss system: installation and diagrams

The gable roof truss system is designed for roofing in the form of two rectangles located at a certain angle to each other in the upper part of the structure.

Do-it-yourself gable roof truss system: an overview of hanging and layered structures

Rafters perform a number of significant roofing functions. They set the configuration of the future roof, perceive atmospheric loads, and hold the material. Among the rafter duties are the formation of even planes for laying the coating and providing space for the components of the roofing pie. In order for such a valuable part of the roof to flawlessly cope with the listed tasks, information about the rules and principles of its construction is needed. The information is useful both for those who are building a gable roof truss system with their own hands, and for those who decide to resort to the services of a hired team of builders.

Rafter structures for gable roofs

In the device of the truss frame for pitched roofs, wooden and metal beams are used. The starting material for the first option is a board, log, beam. The second is constructed from rolled metal: a channel, a profile pipe, an I-beam, a corner. There are combined structures with steel most loaded parts and wood elements in less critical areas.

In addition to the "iron" strength, the metal has a lot of disadvantages. These include heat engineering qualities that do not satisfy the owners of residential buildings. Disappointing need for the use of welded joints. Most often, industrial buildings are equipped with steel rafters, less often private change houses assembled from metal modules.

In the case of self-construction of truss structures for private houses, wood is a priority. It is easy to work with it, it is lighter, “warmer”, more attractive in terms of environmental criteria. In addition, nodal connections do not require a welding machine and welder skills.

Rafters - a fundamental element

The main "player" of the frame for the construction of the roof is the rafter, among the roofers called the rafter leg. Beds, braces, headstocks, girders, puffs, even Mauerlat may or may not be used depending on the architectural complexity and dimensions of the roof.

The rafters used in the construction of the gable roof frame are divided into:

• Layered rafter legs, both heels of which have reliable structural supports under them. The lower edge of the layered rafter rests on the Mauerlat or on the ceiling crown of the log house. The support for the upper edge can be a mirror analogue of an adjacent rafter or a run, which is a beam horizontally laid under the ridge. In the first case, the truss system is called spacer, in the second, non-spacer.
• hanging rafters, the top of which rests against each other, and the bottom is based on an additional beam - puff. The latter connects the two lower heels of adjacent rafter legs, resulting in a triangular module called a truss truss. The tightening dampens the tensile processes, so that only a vertically directed load acts on the walls. The design with hanging rafters, although it is spacer, does not transfer the spacer itself to the walls.

In accordance with the technological specifics of the rafter legs, the structures constructed from them are divided into layered and hanging. For structural stability, they are equipped with struts and additional racks. For the arrangement of supports for the top of the layered rafters, beds and girders are mounted. In reality, the truss structure is much more complicated than the elementary patterns described.

Note that the formation of a gable roof frame can generally be carried out without a truss structure. In such situations, the alleged planes of the slopes are formed by slegs - beams laid directly on the bearing gables. However, we are now specifically interested in the device of the gable roof truss system, and it can involve either hanging or layered rafters, or a combination of both types.

Subtleties of fastening rafter legs

The rafter system is fastened to brick, foam concrete, aerated concrete walls through the mauerlat, which in turn is fixed with anchors. Between the Mauerlat, which is a wooden frame, and the walls of these materials, a waterproofing layer of roofing material, waterproofing, etc. is necessarily laid.

The top of the brick walls is sometimes specially laid out so that something like a low parapet is obtained along the outer perimeter. So it is necessary that the Mauerlat placed inside the parapet and the walls do not burst the rafter legs.

The rafters of the frame of the roofs of wooden houses rest on the upper crown or on the ceiling beams. The connection in all cases is made by cutting and duplicated with nails, bolts, metal or wooden plates.

How to do without furious calculations?

It is highly desirable that the cross section and linear dimensions of the wooden beams be determined by the project. The designer will give clear calculation justifications for the geometric parameters of the board or beam, taking into account the entire range of loads and weather conditions. If there is no home design development master at his disposal, his path lies on the construction site of a house with a similar roof structure.

You can ignore the number of storeys of the building under construction. It is easier and more correct to find out the required dimensions from the foreman than to find them out from the owners of a shaky unauthorized construction. After all, the foreman is in the hands of documentation with a clear calculation of the loads per 1 m² of roof in a particular region.

The installation step of the rafters determines the type and weight of the roofing. The heavier it is, the smaller the distance between the rafter legs should be. For laying clay tiles, for example, the optimal distance between the rafters will be 0.6-0.7 m, and for the installation of metal tiles and profiled sheets, 1.5-2.0 m is acceptable. However, even if the step required for the correct installation of the roof is exceeded, there is a way out . This is a reinforcing counter-lattice device. True, it will increase both the weight of the roof and the construction budget. Therefore, it is better to deal with the step of the rafters before the construction of the rafter system.

Craftsmen calculate the pitch of the rafters according to the design features of the building, tritely dividing the length of the ramp into equal distances. For insulated roofs, the step between the rafters is selected based on the width of the thermal insulation boards.

Rafter structures of layered type

Rafter structures of the layered type are much simpler in execution than their hanging counterparts. A justified plus of the layered scheme is to provide full ventilation, which is directly related to the longevity of the service.

Distinctive design features:

• Mandatory presence of support under the ridge heel of the rafter leg. The role of the support can be played by a run - a wooden beam resting on racks or on the inner wall of the building, or the upper end of an adjacent rafter.
• The use of Mauerlat for the construction of a truss structure on walls made of brick or artificial stone.
• The use of additional runs and racks where the rafter legs, due to the large size of the roof, require additional support points.

The minus of the scheme is the presence of structural elements that affect the layout of the internal space of the operated attic. If the attic is cold and the organization of useful premises is not supposed to be in it, then the layered construction of the truss system for the installation of a gable roof should be preferred.

A typical sequence of work on the construction of a layered truss structure:

• First of all, we measure the height of the building, the diagonals and the horizontalness of the upper cut of the skeleton. When identifying vertical deviations of brick and concrete walls, we eliminate them with a cement-sand screed. Exceeding the heights of the log house we squeeze. By placing chips under the Mauerlat, vertical flaws can be dealt with if their magnitude is insignificant.
• The floor surface for laying the bed must also be leveled. He, the Mauerlat and the run must be clearly horizontal, but the location of the listed elements in the same plane is not necessary.
• We process all wooden parts of the structure before installation with fire retardants and antiseptic preparations.
• We lay waterproofing on concrete and brick walls for the installation of a Mauerlat.
• We lay the Mauerlat beam on the walls, measure its diagonals. If necessary, we slightly move the bars and turn the corners, trying to achieve the perfect geometry. Align the frame horizontally if necessary.
• We mount the Mauerlat frame. The splicing of the beams into a single frame is carried out by means of oblique cuts, the joints are duplicated with bolts.
• We fix the position of the Mauerlat. Fasteners are made either with brackets to wooden plugs laid in the wall ahead of time, or with anchor bolts.
• We mark the position of the bed. Its axis should recede from the Mauerlat bars at equal distances on each side. If the run will be based only on racks without lying down, the marking procedure is carried out only for these columns.
• We install the bed on a two-layer waterproofing. We fasten it to the base with anchor bolts, connect it to the inner wall with wire twists or staples.
• We mark the installation points of the rafter legs.
• We cut out racks according to uniform sizes, because our bed is set to the horizon. The height of the racks must take into account the dimensions of the section of the run and the bed.
• Installing racks. If provided by the project, we fix them with spacers.
• We lay the run on the racks. We check the geometry again, then install the brackets, metal plates, wooden mounting plates.
• We install a trial rafter board, mark the places of trimming on it. If the Mauerlat is set strictly to the horizon, there is no need to adjust the roof rafters in fact. The first board can be used as a template for making the rest.
• We mark the installation points of the rafters. Folk craftsmen for marking usually prepare a pair of slats, the length of which is equal to the gap between the rafters.
• According to the markup, we install the rafter legs and fasten them first at the bottom to the Mauerlat, then at the top to the run to each other. Every second rafter is screwed to the Mauerlat with a wire bundle. In wooden houses, the rafters are screwed to the second crown from the top row.

If the rafter system is done flawlessly, the layered boards are mounted in random order. If there is no confidence in the ideal structure, then the extreme pairs of rafters are installed first. A control twine or fishing line is stretched between them, according to which the position of the newly installed rafters is adjusted.

The installation of the truss structure is completed by installing the filly, if the length of the rafter legs does not allow the formation of an overhang of the required length. By the way, for wooden buildings, the overhang should “go beyond” the contour of the building by 50 cm. If the organization of the visor is planned, separate mini-rafters are installed under it.

Hanging truss systems

The hanging type of truss systems is a triangle. The two upper sides of the triangle are folded by a pair of rafters, and the puff connecting the lower heels serves as the base. The use of tightening allows you to neutralize the effect of the spread, therefore, only the weight of the crate, the roof, plus, depending on the season, the weight of precipitation, acts on walls with hanging truss structures.

The specifics of hanging truss systems

Characteristic features of hanging type truss structures:

• Mandatory presence of a puff, made most often of wood, less often of metal.
• The ability to refuse the use of Mauerlat. A frame made of timber will be successfully replaced by a board laid on a two-layer waterproofing.
• Installation on the walls of ready-made closed triangles - roof trusses.

The advantages of the hanging scheme include the space under the roof free from racks, which allows you to organize an attic without pillars and partitions. There are disadvantages. The first of these is the limitation on the steepness of the slopes: their slope angle can be at least 1/6 of the span of a triangular truss, steeper roofs are strongly recommended. The second disadvantage is the need for thorough calculations for the competent device of cornice nodes.

Among other things, the angle of the truss truss will have to be set with jewelry accuracy, because. the axes of the connected components of the hanging rafter system must intersect at a point, the projection of which must fall on the central axis of the Mauerlat or the lining board replacing it.

Subtleties of long-span hanging systems

Puff - the longest element of the hanging rafter structure. Over time, it, as is typical of all lumber, deforms and sags under the influence of its own weight. Owners of houses with spans of 3-5m are not too concerned about this circumstance, but owners of buildings with spans of 6 meters or more should think about installing additional parts that exclude geometric changes in tightening.

To prevent sagging in the installation scheme of the truss system for a large-span gable roof, there is a very significant component. This is a pendant called a grandmother. Most often, it is a bar attached with wooden surfs to the top of the truss truss. You should not confuse the headstock with the racks, because. its lower part should not come into contact with the puff at all. And the installation of racks as supports in hanging systems is not used.

The bottom line is that the headstock, as it were, hangs on a ridge knot, and a tightening is already attached to it with the help of bolts or nailed wooden plates. Threaded or collet type clamps are used to correct slack.

Adjustment of the tightening position can be arranged in the zone of the ridge knot, and the headstock can be rigidly connected to it with a notch. Instead of a bar in non-residential attics, reinforcement can be used to manufacture the described tightening element. It is also recommended to arrange a headstock or suspension where the puff is assembled from two bars to support the connection area.

In an improved hanging system of this type, strut beams complement the headstock. The stress forces in the resulting rhombus are extinguished spontaneously due to the competent arrangement of the vector loads acting on the system. As a result, the truss system pleases with stability with a slight and not too expensive upgrade.

Hanging type for attics

In order to increase the usable space, the tightening of the rafter triangles for the attic is moved closer to the ridge. A perfectly reasonable move has additional advantages: it allows you to use puffs as the basis for filing the ceiling. It is attached to the rafters by cutting with a semi-frying pan with a duplication of a bolt. It is protected from sagging by installing a short headstock.

A noticeable drawback of the attic hanging structure is the need for accurate calculations. It is too difficult to calculate it on your own, it is better to use a ready-made project.

Which design is more cost effective?

Cost is an important argument for an independent builder. Naturally, the price of construction for both types of truss systems cannot be the same, because:

• In the construction of a layered structure for the manufacture of rafter legs, a board or beam of small section is used. Because layered rafters have two reliable supports under them, the requirements for their power are lower than in the hanging version.
• In the construction of a hanging structure, the rafters are made of thick timber. For the manufacture of puffs, a material similar in cross section is required. Even taking into account the rejection of the Mauerlat, the consumption will be significantly higher.

Saving on the grade of material will not work. For the bearing elements of both systems: rafters, purlins, beds, Mauerlat, attendants, racks, lumber of the 2nd grade is needed. For crossbars and puffs working in tension, you will need the 1st grade. In the manufacture of less responsible wooden slips, the 3rd grade can be used. Without counting, we can say that in the construction of hanging systems, expensive material is used to a greater extent.

Hanging trusses are assembled in an open area next to the object, then transported assembled upstairs. To lift weighty triangular arches from a bar, you will need equipment, for which you will have to pay rent. And the project for complex nodes of the hanging version is also worth something.

There are actually many more methods for constructing truss systems for roofs with two slopes. We have described only the basic varieties that are actually applicable for small country houses and buildings without architectural ideas. However, the information provided is sufficient to cope with the construction of a simple truss structure.

Do-it-yourself gable roof truss system: device, design, installation

In order for the truss system of a gable roof to be built competently and firmly with your own hands, you need information about the rules and principles of the device, fastening and

Construction of houses

When building one-story houses, a roof with two slopes is very popular. This is due to the speed of construction of the structure. In this parameter, only a single-pitched roof can compete with a gable roof. In the device, a gable rafter roof is not too complicated. And you will successfully master this work on your own.

The design of the gable roof truss system

The gable roof consists of two inclined surfaces that have a rectangular shape. Thanks to this, precipitation, which is represented by rain and melt water, flows off the roof in a natural way. The gable roof has a rather complex structure. It consists of such structural units: Mauerlat, rafter system, filly, ridge, roof overhang, bed, struts, puffs, crate and racks:

1. Mauerlat. This element performs the functions of transferring and distributing the load created by the rafter system on the load-bearing walls of the house. For the manufacture of Mauerlat, a beam is used, which has a square section - from 100 by 100 to 150 by 150 mm. It is better to use softwood. The beam is placed around the perimeter of the building and fixed to the outer walls. For fastening use special rods or anchors.
2. Rafter leg. Rafters form the main frame of any roof. In the case of a gable roof, they form a triangle. The rafters are responsible for the uniform transfer of loads to the Mauerlat. First of all, those that arise from precipitation, wind and the weight of the roof itself. For the manufacture of rafters, boards are used that have a section of 100 by 150 or 50 by 150 mm. Choose a rafter pitch of about 60-120 cm, depending on the type of roofing material. When using a heavy coating, place the rafter legs more often.
3. Skate. This element connects two slopes at the top of the roof. The ridge is formed after connecting all the rafter legs.
4. Filly. They act as a continuation of the rafters and form the overhang of the gable roof. It is customary to install fillies if the rafter legs are very short and do not allow an overhang to form. To make this structural unit, take a board that has a smaller section than the rafter. The use of fillies facilitates the construction of the truss system, as it allows the use of short rafters.
5. Eaves. This part of the design of the gable roof truss system is responsible for draining water from the walls during rain and at the same time preventing them from getting wet and quickly destroyed. The overhang protrudes from the wall, as a rule, by 400 mm.
6. Sill. It is located on the inner wall and serves to evenly distribute the load from the roof racks. For the manufacture of bedding, a beam is used, which has a section of 150 by 150 or 100 by 100 mm.
7. Racks. These vertical elements are responsible for transferring the load from the ridge to the interior walls. To create this element, prepare a beam that has a square section of 150 by 150 or 100 by 100 mm.
8. Struts. They are needed to transfer loads from the rafters to the load-bearing walls. Struts and puffs form a solid structure called a truss. Such a device is designed to withstand loads at large spans.
9. Puff. This structural unit, together with the rafters, forms a triangle. It does not allow the rafters to part in different directions.
10. Crate. This design consists of boards and bars. They are attached perpendicular to the rafters. Sheathing is necessary to evenly distribute the weight of the roof covering and the loads created by weather phenomena on the rafters. In addition, the crate is required to fasten the rafters together. When arranging a soft roof, to create a crate, you should not use boards and bars, but moisture-resistant plywood.

Varieties of gable roof truss system

There are gable truss systems with hanging and layered rafters. Ideally, the design contains a combination of them. It is customary to install hanging-type rafters if the outer walls are located at a distance of less than 10 m. Also, there should no longer be walls between them that divide the space of a residential building. The design with hanging rafters creates a bursting force transmitted to the walls. It can be reduced if you arrange a puff made of wood or metal and place it at the base of the rafters.

At the same time, the rafters and tightening form a rigid geometric figure - a triangle. It is not able to deform under loads that are in any direction. The puff will be stronger and more powerful if it is placed higher. The floor beams act as puffs. Thanks to their use, the hanging truss system of a gable roof acts as the basis for the arrangement of the attic floor.

Laminated rafters in their design have a support beam, which is located in the middle. It is responsible for transferring the weight of the entire roof to the intermediate column or middle wall located between the outer walls. It is recommended to install rafters if the outer walls are placed more than 10 m apart. If there are columns instead of internal walls, you can alternate between rafters and hanging rafters.

Do-it-yourself gable truss system

The roof must be strong to withstand various loads - precipitation, gusts of wind, the weight of a person and the roofing itself, but at the same time light, so as not to put a lot of pressure on the walls of the house. A properly arranged gable rafter roof evenly distributes the load on all load-bearing walls.

Calculation of a gable roof

The choice of slope of a gable roof will depend on the material you have chosen for laying on the roof and architectural requirements:

• When building a gable roof, remember that it must slope at an angle of more than 5 degrees. It happens that the slope of the roof reaches 90 °.
• For areas with heavy rainfall, and when the roofing does not fit snugly, steep slopes are made. In this situation, the angle should be 35-40 ° so that precipitation does not linger on the roof. But such an angle does not allow building a living space in the attic. The output will be a broken roof structure. It will have a flat upper part, and on the lower part there will be a sharp slope.
• In regions with strong gusts of wind, sloping roofs are equipped. If constant winds prevail in the area, then make a slope of 15-20 ° for high-quality protection of the roofing.
• It is best to choose the middle option. Equip a gable roof that is not too steep. But also the slope should not be very gentle.
• When choosing a large angle of the roof, its windage increases, and, accordingly, the price of the gable roof truss system and the crate. After all, such a slope entails an increase in the area of ​​\u200b\u200bthe roof and, accordingly, the amount of necessary material - building and roofing.

When buying materials for the construction of a gable roof, it is useful to calculate its area:

1. Find the area of ​​one slope of the structure, and then double the result.
2. Ideally, a slope is an inclined rectangle that is placed along a long load-bearing wall. To determine the area of ​​​​a slope, multiply its length by its width.
3. The length of the slope is equal to the length of the wall. In addition, the length of the ledge of the roof above the gable is added to the length. Remember that the protrusions are present on both sides.
4. The width of the slope is the length of the rafter leg. To it is added the length of the ledge of the roof above the load-bearing wall.

In order to properly design the structure, it is recommended to carry out an accurate calculation of the gable roof truss system, including determining the loads and characteristics of the rafters:

1. When erecting a roof for a standard building that has one floor, the design load on the roof will consist of two values. The first of them is the weight of the roof, the second is the load from external factors: precipitation and wind.
2. Calculate the weight of the roof by adding up the weight of each layer of the "pie" - heat-insulating, vapor barrier and waterproofing materials, truss system, battens and directly roofing material. Calculate the weight per 1 m2.
3. Increase the result by 10%. You can also take into account the correction factor. In our case, K=1.1.
4. If you plan to change the design of the roof over time and increase its angle of inclination, then include a margin of safety in the calculation. Take immediately higher load indicators than those that you received at the time of the calculation. It is recommended to build on the value, which is 50 kg per 1 m2.
5. When calculating the load exerted by atmospheric phenomena, take into account the climatic features of the area where the building is located. In this calculation, take into account the slope of the slope. If the gable roof forms an angle of 25 degrees, then take the snow load equal to 1.
6. If the roof is equipped with a greater slope - up to 60 degrees, the correction factor reaches 1.25. Snow load for an angle greater than 60 degrees is not taken into account.
7. The rafters transfer the entire load from the created structure to the load-bearing walls. Therefore, their parameters must also be taken appropriately. Select the section and length of the rafter leg, depending on the current load on the roof and the angle of the slope. Increase the values ​​obtained by 50% to ensure a high margin of safety.

Mauerlat installation methods

The construction of any roof begins with the installation of a Mauerlat:

• If logs or timber were used to build the walls, then the upper timber will act as a Mauerlat, as shown in the photo of the gable roof truss system.
• If you used bricks to build walls, then brick the metal rods into the masonry. They must have a cut thread for attaching the Mauerlat. Install rods every 1-1.5 m. Choose rods with a diameter of at least 10 mm. Lay waterproofing between masonry and Mauerlat.
• For walls made of ceramic or foam concrete blocks, pour concrete on top. Be sure to make the layer reinforced. It should have a height of approximately 200-300 mm. Be sure to attach metal rods that are threaded to the reinforcement.
• For Mauerlat, use a beam that has a section of 15 by 15 cm. It will act as a kind of foundation for the truss system.
• Lay the Mauerlat on the top edge of the wall. Depending on its design, the Mauerlat can be laid along the outer and inner edges. Do not place it close to the very edge, otherwise it may be blown away by the wind.
• Mauerlat is recommended to be placed on top of the waterproofing layer. To connect all the parts into one whole, use bolts and metal plates.
• To avoid sagging, make a lattice of racks, struts and a crossbar. To do this, take boards measuring 25x150 mm. The angle between the strut and the leg of the rafter should be as straight as possible.
• If using a rafter leg that is too long, install another support. She must lean on the bed. Each element is associated with two adjacent ones. As a result, a stable structure is created around the entire perimeter of the roof.

Rafter leg attachment

The best option for a gable roof truss system is a combination of sloping and hanging rafters. This design allows you to create a reliable gable roof and reduce the cost of building materials. Consider the following recommendations when working:

1. Use only the highest quality wood as a material. Beams that have cracks and knots should not be used.
2. Rafters have standard dimensions - 50x150x6000 mm. When the beams are longer than 6 m, it is recommended to increase the width of the board so that the beams do not break under their own weight. Take boards 180 mm wide.
3. First, make a template for the rafter leg. Attach the board to the floor beam and the end of the ridge beam. Having outlined two lines, saw off a board along them. The template is ready.
4. Cut the rafters according to this pattern. After that, do the top washed down on them.
5. Take the resulting workpiece, bring it to the floor beam to mark the lower cut in place.
6. Install all rafters. At the same time, remember that after installing one leg, you must immediately install the opposite one. So you will quickly remove the lateral loads on the ridge beam.
7. If the slope is too long, then standard boards will not be enough to make a rafter leg. In this case, you can splice two boards together. To do this, sew on them a piece of wood of a similar section. It should have a length of 1.5 - 2 meters. According to the diagram of the gable roof truss system, the joint should always be at the bottom. Under it, install an additional rack.
8. Attach the rafter leg to the ridge beam with nails. Use self-tapping screws to fasten the rafters to the floor beam. Metal mounting plates are also suitable. In addition, a few nails are added.
9. If you are building a structure exclusively from hanging rafters, then skip the next step. When erecting a structure with layered rafters, you need to think about the supports that are installed on their floor. To reduce the deflection of the rafters, correctly calculate the location of such supports.
10. If you're building a gabled mansard roof, the intermediate studs will form the frame for the side walls.
11. When performing this work, maintain a certain step of the beams. Set its size at the design stage.
12. After installing the rafters, attach the ridge. It is located on their upper edge. For fastening use metal corners or staples. Bolts are the most popular.

Giving structure rigidity

After installing the gable roof truss system, strengthen it using the technology below:

• For smaller buildings, such as saunas, cottages, utility buildings, and roofs with a simple hanging rafter system, connect each pair of rafters from below with a tightening and from above using a crossbar.
• For large buildings that are light at the same time, provide a lightweight roof. The walls must support it.
• If the house has a width of 6-8 m, then the structure should be tightened. Install in the middle of the support. Such racks are called grandmas. Place them at each pair of rafter legs.
• If the span of the walls reaches 10 meters, then reinforcing beams will be needed. The struts act as an additional support for the rafter legs for tightening. They are attached to each rafter - closer to the ridge or in the middle of the rafter leg. Fasten them to the bottom end of the headstock and to each other as shown in the gable roof truss video.
• In a situation with long roofs, gable beams should be relieved. This is done by installing braces. The upper end should rest against the corner of the gable. The lower one is mounted on the central floor beam. For fasteners, use a beam that has a large cross section. So you can prevent them from breaking if there are strong gusts of wind.
• In areas where winds predominate, the rafters must be resistant to such influences. Strengthen them by installing diagonal ties. Boards are nailed from the bottom of one rafter to the middle of the next.
• For greater rigidity, when creating the most critical fasteners, it is better not to use nails. Use pads and metal fasteners for this. Nails will not be able to provide high-quality fastening, since the wood can dry out after some time.

Lathing of the truss system

The final stage of the construction of the gable roof truss system is the creation of the crate. It is on it that you will lay the roofing. Carry out the work in the following sequence:

1. Select a dry timber for the crate. It should not have cracks or knots. Nail the bars on the bottom. Attach two boards near the ridge so that there are no gaps. The lathing must withstand the weight of the top roofing material and not sag under the weight of the workers.
2. If you will equip a soft roof, make two layers of sheathing. One is sparse, the other is solid. The same applies to roll roofing. To begin with, parallel to the ridge beam, place boards that are 25 mm thick and no more than 140 mm wide. A small gap is allowed - no more than 1 cm. Lay a continuous layer on top. To do this, it is better to use roofing plywood, slats or boards of small thickness. After that, check that there are no errors left on the crate - bumps and knots. Also check that the nail heads are not sticking out.
3. Lay one layer of timber under the metal tile. It should have a section of 50 by 60 mm. Do the same when using slate or steel roofing sheets. Maintain a step between the timber, depending on the roofing you choose - from 10 to 50 cm. Hammer nails closer to the edges of the board, and not in the middle. Drive hats deep. So they will not be able to damage the roof later. If you are making a crate for a metal tile, then remember that the connection of the timber at the same level should fall on the rafters.

When you have installed and strengthened the gable roof truss system, you can start installing the roofing pie. Place a thermal insulation material between the rafters, a layer of vapor barrier and waterproofing. When using insulation in slabs, calculate in advance the pitch of the rafters for its installation. At the final stage, fasten the roofing material.

The device of the gable roof truss system, Building Portal

Construction of houses In the construction of one-story houses, a roof with two slopes is very popular. This is due to the speed of construction of the structure. For this setting,

Due to its simple structure, ease of maintenance and durability for long-term use, a gable roof is the most common solution in home improvement.

Types and features of a gable roof

The shape of a gable roof is determined at the design stage. It largely depends on the further operation of the attic. There are three main types of gable roof:

• Symmetrical. The most common option provides a reliable device and even distribution of loads. The risk of bending the rafters is practically absent. A significant drawback is the impossibility of arranging the attic. Sharp corners form sections of the attic that are unsuitable for use.
• Simple asymmetrical. The formation of one angle exceeding 45 about, provides an increase in usable area. This allows you to organize additional living rooms under a gable roof. The uneven distribution of the load on the foundation and load-bearing walls causes difficulties at the stage of calculations for the installation of rafters.
• broken line . The fracture of a gable roof can be internal or external. Thanks to the non-standard design, it becomes possible to use the attic area for arranging a full-fledged second floor. Calculations for the installation of rafters are much more complicated.

Calculating the correct angle of inclination is a key task prior to installing rafters for a gable roof. The climatic features of the region are taken into account. The presence of frequent and heavy rainfall necessitates the arrangement of a steep slope of a gable roof. The installation of gentle slopes is preferable with significant wind loads. With a possible range from 5 to 90 o, the most common version of the roof has a slope of 35 to 45 o, characterized by savings in material consumption and uniform load distribution.

Rafter system options

Mauerlat and the truss system are the supporting elements of a gable structure. The rafters themselves consist of several parts:

• rafter legs and puffs that connect them and stiffen them;
• vertical racks;
• crossbars;
• ridge and side runs;
• longitudinal struts, in regions with significant snow and wind loads, additional installation of diagonal braces is carried out;
• spacers;
• bed and crate.

Advice ! The rafter scheme necessarily includes the installation of a chimney and a ventilation shaft.

For the selected gable design, there are three options for installing rafters. Consider the features of each method.

• If the roof is less than 6 pm in width, the option of installing hanging rafters is considered. The process consists in fixing the leg between the ridge run and the supporting wall. This provides a reduction in the impact of the bursting force on the rafter legs. The connection of the elements of the rafters is carried out using a puff made of wood or metal. Their installation at the bottom allows you to perform the function of load-bearing beams. An indispensable condition is reliable fixation of the puff, as it is subjected to bursting influences.
• Sloped rafters are not limited to the size of gable structures, they include a bed and racks. A significant advantage of this type of rafters is ease of installation. The presence of a rack overshadows the practicality of the design.
• Complex configurations of gable roofs provide for the installation of combined rafters.

Having determined the appropriate type of rafter system, they proceed to the calculation of the amount of material. In addition, each element of the roof needs a separate drawing and fixing the results of the calculations.

Calculation of the truss system

In fact, the truss system is triangular elements connected together, characterized by maximum rigidity. If the gable roof has a broken structure, irregular rectangles need to be broken down into separate components, followed by the calculation of the loads for each part. At the final stage, the data are summarized.

Determination of permanent and live loads

An essential condition for the installation of rafters is the determination of loads on a gable roof. They are divided into permanent, variable and special. The components of the magnitude of constant loads are the weight of the crate, attic finishing materials, insulation and other elements that generally form the weight of the roof. On average, this indicator of the load on the rafters is 40-45 kg m 2.

Advice ! The calculation of the strength of a gable structure provides for a 10% margin.

Focusing on the indicators of the table indicating the weight of individual materials for roofing, you should adhere to the maximum load of 50 kg per 1 m 2 of the roof area.

The very name of variable loads speaks of their intermittent action. This includes the force of the wind, the action of snow cover and other types of intense influence of weather conditions. A gable roof is like a sail; an incorrectly calculated angle of inclination can provoke its destruction under the influence of strong winds. To calculate this parameter, they refer to the indicators specified in the SNiP “Loads and Impacts”, taking into account the accompanying factors (the location of the house in an open space or among high-rise buildings). The determination of the effect of snow cover on a gable roof is the product of the weight of the snow and a correction factor that takes into account aerodynamic effects. According to SNiP, the weight of snow ranges from 80-560 kg / m 2. The dependence of the coefficients on the angle of the roof is shown in the following figure:

If the angle exceeds 60 °, this parameter is not taken into account due to the impossibility of delaying the snow cover on a gable structure. Special loads are provided for in regions with increased seismic activity, with possible storm winds or tornadoes, which is not typical for most territories.

Calculation of technical parameters of rafters

The installation of rafters is repelled from the shape of a gable roof, the more complex it is, the more rafter elements the system includes. When using a soft roof, the angle of inclination of the roof does not exceed 20 °, steeper structures require the installation of ondulin, metal tiles or standard slate.

The choice of rafter pitch depends on the material used for the roof and the weight of the gable structure, it varies between 0.6-1.0 m. The number of legs is determined by dividing the length of the roof by the gap between the rafter pairs, followed by adding 1. The result shows the number of legs per one side of the roof, to determine the total indicator, the figure is doubled.

Installation of rafters will not do without determining their length, for which the Pythagorean theorem is used (c 2 \u003d a 2 + b 2), where:

• The height of the roof (a) is selected based on the possibility of further operation of the attic space.
• Let's denote half the width of the house as b.
• The hypotenuse (c) represents the desired value - the length of the rafters.

Remark ! The result obtained should be increased by 0.6-0.7 m for sawing and moving the rafter element out of the wall.

If the maximum length of the timber of 6 pm is not enough to install the rafter leg, it is used to splice it by joining or building.

When determining the cross section of the rafters, the following factors are taken into account:

• constant and variable loads:
• what kind of roofing material will be installed;
• type of wood used;
• the length of the rafter legs and the step between them.

The table below will help determine the parameter you are looking for:

Rafter installation step (m)	Rafter leg length, m

Analyzing the data, a pattern is revealed: an increase in the installation step of the rafters proportionally increases the load on each leg, therefore, its cross section should increase.

Approximate sections of individual elements of the gable roof truss system are given below:

Installation of a gable roof

After a thorough recheck of the calculations, they proceed to install the Mauerlat.

Mauerlat

Mauerlat installation includes the following steps:

• Fixing the beam on the wall, designed to support the rafters. If the house is made of a log house, the upper crown performs the function of the Mauerlat. Buildings made of porous material require the installation of a Mauerlat along the entire length of the load-bearing wall.
• The problem of exceeding the standard dimensions of lumber when installing a Mauerlat is solved by splicing them.
• To connect the Mauerlat of a gable roof, the beam is cut exclusively at a right angle, the function of the link is performed by bolts. The use of wire, nails and wooden dowels is not acceptable.

The Mauerlat can be installed in the center of the supporting wall or offset. When fixing the structure, at least 5 cm should remain to the outer boundary of the wall. The use of waterproofing protection will protect the wooden frame of the gable roof from moisture damage. Reliable fastening is an essential condition for installing rafters and Mauerlat on a gable roof. There are several ways to fulfill this requirement:

• anchor bolts are ideal for a monolithic structure;
• it is preferable to equip log cabins with wooden dowels;
• porous materials are well combined with reinforcement or studs;
• annealed wire is used as an additional fastener when installing rafters;
• hinged fastening involves the displacement of the rafter legs in the process of shrinking the house.

Rafter installation

Installation of rafter pairs is carried out in two ways: directly on the roof, which is very impractical, or on the ground. With the second method, difficulties may arise when moving the assembled elements to the roof. The installation of the assembled pairs on the Mauerlat is preceded by the preparation of cuts, they are made exclusively on the rafter leg, so as not to weaken the base of the wooden structure. Mounting options are shown below:

To install paired rafters, temporary struts and struts are used. The ridge knot is formed by joining the rafter legs at the top. The process involves several options for completing the task:

• the small design of the gable roof allows the absence of a support beam;
• large dimensions require the use of a rafter beam, which later serves as a support for the rack.
• cutting method.

Arrangement options are shown in the photo:

The installation of the crate facilitates the fastening of the roofing material, its step directly depends on the coating used:

• a maximum step of 44 cm is possible when arranging the roof with slate or corrugated board;
• a distance of 350 mm will be sufficient when covered with metal tiles;
• soft roof provides a continuous crate.

The installation of rafters contains a lot of nuances that are difficult to foresee in advance. Templates made of thin boards are capable of facilitating the preparation of cuts and cuts. The video will also answer some of your questions.

Rafters perform a number of significant roofing functions. They set the configuration of the future roof, perceive atmospheric loads, and hold the material. Among the rafter duties are the formation of even planes for laying the coating and providing space for the components of the roofing pie.

In order for such a valuable part of the roof to flawlessly cope with the listed tasks, information about the rules and principles of its construction is needed. The information is useful both for those who are building a gable roof truss system with their own hands, and for those who decide to resort to the services of a hired team of builders.

In the device of the truss frame for pitched roofs, wooden and metal beams are used. The starting material for the first option is a board, log, beam.

The second is constructed from rolled metal: a channel, a profile pipe, an I-beam, a corner. There are combined structures with steel most loaded parts and wood elements in less critical areas.

In addition to the "iron" strength, the metal has a lot of disadvantages. These include heat engineering qualities that do not satisfy the owners of residential buildings. Disappointing need for the use of welded joints. Most often, industrial buildings are equipped with steel rafters, less often private change houses assembled from metal modules.

In the case of self-construction of truss structures for private houses, wood is a priority. It is easy to work with it, it is lighter, “warmer”, more attractive in terms of environmental criteria. In addition, nodal connections do not require a welding machine and welder skills.

Rafters - a fundamental element

The main "player" of the frame for the construction of the roof is the rafter, among the roofers called the rafter leg. Beds, braces, headstocks, girders, puffs, even Mauerlat may or may not be used depending on the architectural complexity and dimensions of the roof.

The rafters used in the construction of the gable roof frame are divided into:

• Layered rafter legs, both heels of which have reliable structural supports under them. The lower edge of the layered rafter rests on the Mauerlat or on the ceiling crown of the log house. The support for the upper edge can be a mirror analogue of an adjacent rafter or a run, which is a beam horizontally laid under the ridge. In the first case, the truss system is called spacer, in the second, non-spacer.
• hanging rafters, the top of which rests against each other, and the bottom is based on an additional beam - puff. The latter connects the two lower heels of adjacent rafter legs, resulting in a triangular module called a truss truss. The tightening dampens the tensile processes, so that only a vertically directed load acts on the walls. The design with hanging rafters, although it is spacer, does not transfer the spacer itself to the walls.

In accordance with the technological specifics of the rafter legs, the structures constructed from them are divided into layered and hanging. For structural stability, they are equipped with struts and additional racks.

For the arrangement of supports for the top of the layered rafters, beds and girders are mounted. In reality, the truss structure is much more complicated than the elementary patterns described.

Note that the formation of a gable roof frame can generally be carried out without a truss structure. In such situations, the alleged planes of the slopes are formed by slegs - beams laid directly on the bearing gables.

However, we are now specifically interested in the device of the gable roof truss system, and it can involve either hanging or layered rafters, or a combination of both types.

Subtleties of fastening rafter legs

The rafter system is fastened to brick, foam concrete, aerated concrete walls through the mauerlat, which in turn is fixed with anchors.

Between the Mauerlat, which is a wooden frame, and the walls of these materials, a waterproofing layer of roofing material, waterproofing, etc. is necessarily laid.

The top of the brick walls is sometimes specially laid out so that something like a low parapet is obtained along the outer perimeter. So it is necessary that the Mauerlat placed inside the parapet and the walls do not burst the rafter legs.

The rafters of the frame of the roofs of wooden houses rest on the upper crown or on the ceiling beams. The connection in all cases is made by cutting and duplicated with nails, bolts, metal or wooden plates.

How to do without furious calculations?

It is highly desirable that the cross section and linear dimensions of the wooden beams be determined by the project. The designer will give clear calculation justifications for the geometric parameters of the board or beam, taking into account the entire range of loads and weather conditions. If there is no home design development master at his disposal, his path lies on the construction site of a house with a similar roof structure.

You can ignore the number of storeys of the building under construction. It is easier and more correct to find out the required dimensions from the foreman than to find them out from the owners of a shaky unauthorized construction. After all, the foreman is in the hands of documentation with a clear calculation of the loads per 1 m² of roof in a particular region.

The installation step of the rafters determines the type and weight of the roofing. The heavier it is, the smaller the distance between the rafter legs should be. For laying clay tiles, for example, the optimal distance between the rafters will be 0.6-0.7 m, and for a profiled sheet, 1.5-2.0 m is acceptable.

However, even if the step required for the correct installation of the roof is exceeded, there is a way out. This is a reinforcing counter-lattice device. True, it will increase both the weight of the roof and the construction budget. Therefore, it is better to deal with the step of the rafters before the construction of the rafter system.

Craftsmen calculate the pitch of the rafters according to the design features of the building, tritely dividing the length of the ramp into equal distances. For insulated roofs, the step between the rafters is selected based on the width of the thermal insulation boards.

On our website you can find, which may also help you a lot during construction.

Rafter structures of layered type

Rafter structures of the layered type are much simpler in execution than their hanging counterparts. A justified plus of the layered scheme is to provide full ventilation, which is directly related to the longevity of the service.

Distinctive design features:

• Mandatory presence of support under the ridge heel of the rafter leg. The role of the support can be played by a run - a wooden beam resting on racks or on the inner wall of the building, or the upper end of an adjacent rafter.
• The use of Mauerlat for the construction of a truss structure on walls made of brick or artificial stone.
• The use of additional runs and racks where the rafter legs, due to the large size of the roof, require additional support points.

The minus of the scheme is the presence of structural elements that affect the layout of the internal space of the operated attic.

If the attic is cold and the organization of useful premises is not supposed to be in it, then the layered construction of the truss system for the installation of a gable roof should be preferred.

A typical sequence of work on the construction of a layered truss structure:

• First of all, we measure the height of the building, the diagonals and the horizontalness of the upper cut of the skeleton. When identifying vertical deviations of brick and concrete walls, we eliminate them with a cement-sand screed. Exceeding the heights of the log house we squeeze. By placing chips under the Mauerlat, vertical flaws can be dealt with if their magnitude is insignificant.
• The floor surface for laying the bed must also be leveled. He, the Mauerlat and the run must be clearly horizontal, but the location of the listed elements in the same plane is not necessary.
• We process all wooden parts of the structure before installation with fire retardants and antiseptic preparations.
• We lay waterproofing on concrete and brick walls for the installation of a Mauerlat.
• We lay the Mauerlat beam on the walls, measure its diagonals. If necessary, we slightly move the bars and turn the corners, trying to achieve the perfect geometry. Align the frame horizontally if necessary.
• We mount the Mauerlat frame. The splicing of the beams into a single frame is carried out by means of oblique cuts, the joints are duplicated with bolts.
• We fix the position of the Mauerlat. Fasteners are made either with brackets to wooden plugs laid in the wall ahead of time, or with anchor bolts.
• We mark the position of the bed. Its axis should recede from the Mauerlat bars at equal distances on each side. If the run will be based only on racks without lying down, the marking procedure is carried out only for these columns.
• We install the bed on a two-layer waterproofing. We fasten it to the base with anchor bolts, connect it to the inner wall with wire twists or staples.
• We mark the installation points of the rafter legs.
• We cut out racks according to uniform sizes, because our bed is set to the horizon. The height of the racks must take into account the dimensions of the section of the run and the bed.
• Installing racks. If provided by the project, we fix them with spacers.
• We lay the run on the racks. We check the geometry again, then install the brackets, metal plates, wooden mounting plates.
• We install a trial rafter board, mark the places of trimming on it. If the Mauerlat is set strictly to the horizon, there is no need to adjust the roof rafters in fact. The first board can be used as a template for making the rest.
• We mark the installation points of the rafters. Folk craftsmen for marking usually prepare a pair of slats, the length of which is equal to the gap between the rafters.
• According to the markup, we install the rafter legs and fasten them first at the bottom to the Mauerlat, then at the top to the run to each other. Every second rafter is screwed to the Mauerlat with a wire bundle. In wooden houses, the rafters are screwed to the second crown from the top row.

If the rafter system is done flawlessly, the layered boards are mounted in random order.

If there is no confidence in the ideal structure, then the extreme pairs of rafters are installed first. A control twine or fishing line is stretched between them, according to which the position of the newly installed rafters is adjusted.

The installation of the truss structure is completed by installing the filly, if the length of the rafter legs does not allow the formation of an overhang of the required length. By the way, for wooden buildings, the overhang should “go beyond” the contour of the building by 50 cm. If the organization of the visor is planned, separate mini-rafters are installed under it.

Another useful video about the construction of a gable truss base with your own hands:

Hanging truss systems

The hanging type of truss systems is a triangle. The two upper sides of the triangle are folded by a pair of rafters, and the puff connecting the lower heels serves as the base.

The use of tightening allows you to neutralize the effect of the spread, therefore, only the weight of the crate, the roof, plus, depending on the season, the weight of precipitation, acts on walls with hanging truss structures.

The specifics of hanging truss systems

Characteristic features of hanging type truss structures:

• Mandatory presence of a puff, made most often of wood, less often of metal.
• The ability to refuse the use of Mauerlat. A frame made of timber will be successfully replaced by a board laid on a two-layer waterproofing.
• Installation on the walls of ready-made closed triangles - roof trusses.

The advantages of the hanging scheme include the space under the roof free from racks, which allows you to organize an attic without pillars and partitions. There are disadvantages.

The first of these is the limitation on the steepness of the slopes: their slope angle can be at least 1/6 of the span of a triangular truss, steeper roofs are strongly recommended. The second disadvantage is the need for thorough calculations for the competent device of cornice nodes.

Among other things, the angle of the truss truss will have to be set with jewelry accuracy, because. the axes of the connected components of the hanging rafter system must intersect at a point, the projection of which must fall on the central axis of the Mauerlat or the lining board replacing it.

Subtleties of long-span hanging systems

Puff - the longest element of the hanging rafter structure. Over time, it, as is typical of all lumber, deforms and sags under the influence of its own weight.

Owners of houses with spans of 3-5m are not too concerned about this circumstance, but owners of buildings with spans of 6 meters or more should think about installing additional parts that exclude geometric changes in tightening.

To prevent sagging in the installation scheme of the truss system for a large-span gable roof, there is a very significant component. This is a pendant called a grandmother.

Most often, it is a bar attached with wooden surfs to the top of the truss truss. You should not confuse the headstock with the racks, because. its lower part should not come into contact with the puff at all. And the installation of racks as supports in hanging systems is not used.

The bottom line is that the headstock, as it were, hangs on a ridge knot, and a tightening is already attached to it with the help of bolts or nailed wooden plates. Threaded or collet type clamps are used to correct slack.

Adjustment of the tightening position can be arranged in the zone of the ridge knot, and the headstock can be rigidly connected to it with a notch. Instead of a bar in non-residential attics, reinforcement can be used to manufacture the described tightening element. It is also recommended to arrange a headstock or suspension where the puff is assembled from two bars to support the connection area.

In an improved hanging system of this type, strut beams complement the headstock. The stress forces in the resulting rhombus are extinguished spontaneously due to the competent arrangement of the vector loads acting on the system.

As a result, the truss system pleases with stability with a slight and not too expensive upgrade.

Hanging type for attics

In order to increase the usable space, the tightening of the rafter triangles for the attic is moved closer to the ridge. A perfectly reasonable move has additional advantages: it allows you to use puffs as the basis for filing the ceiling.

It is attached to the rafters by cutting with a semi-frying pan with a duplication of a bolt. It is protected from sagging by installing a short headstock.

A noticeable drawback of the attic hanging structure is the need for accurate calculations. It is too difficult to calculate it on your own, it is better to use a ready-made project.

Which design is more cost effective?

Cost is an important argument for an independent builder. Naturally, the price of construction for both types of truss systems cannot be the same, because:

• In the construction of a layered structure for the manufacture of rafter legs, a board or beam of small section is used. Because layered rafters have two reliable supports under them, the requirements for their power are lower than in the hanging version.
• In the construction of a hanging structure, the rafters are made of thick timber. For the manufacture of puffs, a material similar in cross section is required. Even taking into account the rejection of the Mauerlat, the consumption will be significantly higher.

Saving on the grade of material will not work. For the bearing elements of both systems: rafters, purlins, beds, Mauerlat, attendants, racks, lumber of the 2nd grade is needed.

For crossbars and puffs working in tension, you will need the 1st grade. In the manufacture of less responsible wooden slips, the 3rd grade can be used. Without counting, we can say that in the construction of hanging systems, expensive material is used to a greater extent.

Hanging trusses are assembled in an open area next to the object, then transported assembled upstairs. To lift weighty triangular arches from a bar, you will need equipment, for which you will have to pay rent. And the project for complex nodes of the hanging version is also worth something.

Video instruction on the installation of a truss structure of a hanging category:

There are actually many more methods for constructing truss systems for roofs with two slopes.

We have described only the basic varieties that are actually applicable for small country houses and buildings without architectural ideas. However, the information provided is sufficient to cope with the construction of a simple truss structure.