How to glue wallpaper in the corners of the kitchen: glue the corners with wallpaper correctly, decorate the outer corner, non-woven trellises, instructions, video. Proper wallpapering in the corners of a room How to wallpaper in the corners of a room

Gluing modern wallpaper is a simple matter. Even a beginner in the repair business will cope with this. But, if mounting canvases on smooth walls is easy and simple, then you will have to tinker with the corners. It is the corners that become the stumbling block that slows down the whole process and requires a lot of effort. More often than others, non-woven wallpaper or non-woven vinyl canvases are used in repairs.

Material Features

The wallpaper, which consists entirely of non-woven fabric, is easy to install and durable. They are made of non-woven cellulose with the addition of synthetic components. The cellulose component gives the wallpaper elasticity and breathability, while synthetics add strength. Such wallpaper is much more difficult to tear than paper-based vinyl, for example. In addition, they do not crumple at all, there are no bends on the surface.

Non-woven vinyl wallpapers have the same properties. The only difference is that the canvases do not “breathe”, since vinyl does not let air through. Therefore, before gluing them to the walls, it is necessary to treat the surfaces with antibacterial primer or use glue with fungicidal additives. These measures will prevent the appearance of mold and mildew.

Non-woven wallpaper has a number of advantages over other coatings:

1. Their feature is good adhesion with glue and with any wall material. Such canvases do not need to be treated with an adhesive, it is applied only to the walls. The same applies to non-woven vinyl.
2. A useful quality of non-woven fabric is its resistance to stretching. The material does not shrink after the glue dries, the dimensions of the canvas do not change. Thanks to this, the joints do not diverge, and the seams between the strips remain invisible. This feature is especially useful for wallpaper intended for painting, as painting makes all wall defects even more noticeable.
3. Interlining cannot be washed, but can be dyed. But cellulose-based vinyl can even be cleaned with detergents, it also lends itself well to dyeing.
4. Due to the volume of cellulose fibers, such wallpapers align the walls, hide small irregularities. Durable synthetic components are resistant to tearing, this allows non-woven wallpaper to reinforce the walls. They do not allow cracking, holding the plaster.
5. Wallpaper on non-woven base can be easily removed, their two-layer allows you to leave the substrate on the surface and use it as a basis for new coatings.

Installation of wallpaper on the walls

There are several ways to glue wallpaper (it is easy to see them from a photo or video). One of them involves the initial pasting of all smooth walls, and then the corners. Other masters advise starting from the most noticeable corner in the room. There is no consensus on this issue - everyone can glue at their own discretion.

Wall preparation is a must for any method. The old coating must be carefully removed, the cracks must be puttied. Then the walls are covered with a special primer or wallpaper paste. Only after complete drying of the primer proceed to pasting the walls.

In place of the reference point, a vertical line is drawn; this should be done with a plumb line or a building level. The first strip is cut from the roll, the length of which is equal to the height of the wall plus 5-7 cm. The wall is carefully coated with glue and wallpaper is applied. Level the canvas with a plastic spatula or wallpaper roller, focusing on the vertical.

Advice! It is better to use a special glue with a color indicator - in liquid form, such a composition has a pink tint, and after drying it becomes colorless. This allows you to evenly apply glue to the wall, leaving no "gaps".

At the plinth and under the ceiling, the wallpaper is cut with sharp scissors or a construction knife. Move on to the next lane.

How to glue wallpaper in the corners

In order to qualitatively paste over the corners, you first need to deal with their types. Angles are:

• Internal - each room has at least several of these corners (four in the standard layout). A very important factor is the correctness of these plots. If the angle is uneven, has drops, “sinks”, the wallpapering method will differ from the standard one.
• External corners in apartments have become more common with the advent of drywall - a variety of niches, arches, columns and other decorative elements. This also includes door and window slopes, unless, of course, it is provided to start wallpaper on these areas.

The easy way

The easiest way to paste over a completely flat corner. Unfortunately, these are quite rare. These are either drywall constructions, or walls prepared for painting (plastered perfectly smooth and even).

In this case, both in the inner and in the outer corners, the wallpaper is glued in the same way - they simply turn into a single piece of wallpaper. The main thing is not to stretch the coating, after drying it can return to its original size and shape. If there are small wrinkles on the wallpaper, it is allowed to make several horizontal cuts in the corner. This will help even out the coating, and cuts after drying will not be noticeable.

Important! No matter how even the corner is, it is better not to use the method of gluing it with a solid canvas if it is joined to the outer wall. In the corners located near the outer walls, condensation appears more often - the wallpaper can peel off and deform.

Standard Corner Taping Method

It is more reliable to glue wallpaper in the corners using the "overlap" method. Its essence is as follows:

1. After gluing the adjacent wall at three points, measure the distance to the corner.
2. According to the largest of the three values ​​\u200b\u200bobtained, a strip is cut off - its width is equal to the largest figure plus 2-3 cm for overlap.
3. The wall is well coated with glue, especially paying attention to the corner (it is better to use a brush).
4. The prepared piece of wallpaper is applied to the corner, combining the joint with the previous canvas.
5. The overlap formed on the adjacent wall is carefully pressed, tucking the wallpaper into the corner with a plastic spatula.
6. For a tighter fit, the edge of the wallpaper can be trimmed - short horizontal cuts are made every 5 cm.
7. Trim the bottom and top edges of the wallpaper using a metal spatula and a sharp knife.
8. From the narrowest point of the overlap, they recede about one centimeter towards the corner, make a mark.
9. Focusing on the mark, draw a vertical line in this place using a plumb line or level.
10. Prepare the next strip (if necessary, select a pattern).
11. A strip is applied to the wall smeared with glue, aligning its edge with the previously drawn line in the corner.
12. Level the strip, expelling air and excess glue. Cut under the ceiling and near the floor.

Corner done! They proceed to pasting a flat wall to the next corner - the procedure is repeated. In this way, you can glue the outer corners with diverse wallpaper

Advice! Given the considerable thickness of non-woven wallpaper, the overlap may be too noticeable.

In this way, you can paste over those corners that furniture or curtains will hide, and choose another way to finish the rest. You can also try cutting off only the top layer of wallpaper.

Slopes do not have to be glued with wallpaper, the video shows how they can be beautifully trimmed at the corners:

Corner cutting method

If the walls are supposed to be painted, there should not be any overlaps on them. The paint will make the thickening of the wallpaper too noticeable, here you need another way. This method is suitable for both internal and external corners.

The work is performed in the following sequence:

1. The first seven points from the previous instructions are repeated - the strip is glued with an overlap on the next wall. Only in this case, the overlap is made larger - 5-7 cm.
2. A distance equal to the width of the roll minus one centimeter recede from the corner.
3. Using a plumb line or level, draw a vertical line at this point.
4. A strip is cut off from the roll and applied to the wall smeared with glue, aligning the edge with the drawn strip.
5. The second edge is applied to the previous strip with an overlap, the wallpaper is pressed and leveled.
6. Carefully push the wallpaper into the corner with a spatula, leveling everything again.
7. In the middle of the overlap, a metal ruler is vertically applied, a very sharp knife is taken and a line is drawn without interruption along the edge of the ruler. It is very important that the line is drawn in one motion.
8. They remove the trim of the upper canvas, bend the edge of the lower one and also remove the excess.
9. Both edges are smeared with glue and folded end-to-end. You can pull the canvas a little in the right direction so that there is no gap or overlap.
10. Rolled with a roller for joints.

This method helps to make the connection of the canvases invisible. It works well on external corners, in niches and on slopes.

Advice! It is better to use a small metal spatula 10-15 cm instead of a ruler

Due to the unevenness of the corners, the ruler may not fit snugly against the wall, the cut will turn out to be crooked. The spatula must be moved along with the knife, avoiding breaks in the cut line. How to properly trim the wallpaper in the corners, you can see in the video:

Tsugunov Anton Valerievich

Reading time: 4 minutes

Wallpaper is a universal finishing material, the main advantage of which is the relative ease of working with it. With their sticking, you can successfully cope on your own, without resorting to the help of specialists. But if the decision is made to transform the appearance of the room on its own, it is important to understand how to properly glue the wallpaper in the corners. It is this part of the work that is the most difficult.

Preparatory activities

Criteria for choosing wallpaper for uneven walls and corners

If there is no desire or opportunity to engage in leveling the base, you need to approach more carefully.

• The material for curved surfaces should be loose so that those joints where overlapping strips will have to be glued are not conspicuous. Non-woven fabrics are well suited.
• The drawing should be small and frequent or completely absent.
• The unevenness of the walls will help hide the material with a relief structure.
• For heavily damaged surfaces, fiberglass wallpaper is suitable for painting.

Work materials

Regardless of the type of canvas chosen, before gluing, it is necessary to prepare the following tools and materials:

• rolls in the right quantity;
• wallpaper glue suitable for the selected type of wallpaper;
• roulette;
• a long ruler made of metal or a piece of profile;
• plumb;
• pencil;
• construction knife or sharp paper blade;
• rubber roller, brush or clean cloth.

Tip: do not start gluing wallpaper from the corner, to start work, select a flat part of the wall.

Experts have their own secrets for pasting corner elements.

• I glue it on. When gluing wallpaper in a butt corner, there is a risk of the canvases diverge after drying and the appearance of a gap that cannot be imperceptibly removed.
• We do not glue the whole canvas, even if the corner is perfectly even. Otherwise, after drying, folds and distortions are almost inevitably formed.
• Coat the wall with glue. It is in the corners that the probability of material lagging is especially high, therefore this rule applies to all types of canvases: paper, non-woven, vinyl.

Wallpapering inside corners

For pasting the inner corner, follow the following procedure.

• We measure the distance from the edge of the strip that was last pasted on the wall to the corner. We add 2 cm to the obtained value. We cut the canvas, bend it according to the added allowance and transfer it to the wall smeared with glue. The excess must go to the adjacent side. The glued sheet must be smoothed with a roller or a rag so that all the air comes out from under it.

• We also bend the second sheet by 2 cm and glue it on the other side of the corner so that the allowance overlaps on the previously glued sheet. The correctness of gluing this canvas must be checked with a plumb line. While smoothing the sheet, we try not to press those very few centimeters of the allowance.

• We don’t need two layers of wallpaper, they will stand out, so we attach a long ruler to the corner and cut the layers along it with a construction knife. Then remove the excess top coat.
• Raising the top layer, remove the lower segments, coat its edge again with glue and press it tightly against the wall, squeezing out the air. This method allows you to get a very even butt joint.

Wallpapering in outer corners

To wallpaper the outer corner with wallpaper, you need to calculate the width of the canvas so that the sheet, bending around the ledge, passes to the adjacent wall by 2–5 cm. Having measured the required width of the canvas, cut off the excess part. Remember that when using too wide a strip, we will inevitably get folds and wrinkles.

• We apply glue both on the wallpaper and on the wall. We apply the sheet to the ledge so that the canvas wraps around it, as in the next photo. If the material is dense, you need to make small cuts for good contact with the corner.

• We press the sheet in its upper part. At the bottom of the excess canvas we make an incision. If the material for gluing is smooth, smooth it with a roller, press the embossed one with a cloth. The part of the strip that has gone around the turn can be cut off, leaving a small edge.

• We take the next sheet or the remainder of the previous one and paste it in the same way on the adjacent wall. The canvas should overlap on the first layer. Using a plumb line, we check the verticality of this strip, if necessary, we combine the pattern. Carefully smooth out the fabric.

Sticker wallpaper in the corners is the most difficult. Both the material itself and the properly prepared plane are important here. How to glue wallpaper in the corners, we will consider in this article. Expert advice will also be given. On the video and photo you can see everything yourself and better understand.

For an ideal result, without cutting the wallpaper at the fold, the corners in the room must be even. In such a situation, all the work will consist in processing the walls and wallpaper with an adhesive composition with further pasting.

However, it is very difficult to find a room with perfectly even, geometrically correct characteristics, even if one corner will spoil the overall picture.

What will affect the work:

Possible problems and subtleties when gluing wallpaper on corners

An important point, when performing this type of work, is the material from which the selected wallpaper was made. Different materials behave differently during the gluing process. And when doing the work with your own hands, you need to know these subtleties.

The instruction in this matter will be as follows:

Note: The overlap depends on how dense the material is. For example, if glass wall paper is used, the strips are glued joint to joint. Even a slight overlap will be noticeable.

How to glue wallpaper on an inner corner

The main goal when sticking wallpaper is to prevent “wrinkles” from appearing in the corners, and the wallpaper sheets themselves do not diverge.

So:

• To prevent this from happening, the canvas is wound up so that a grip of no more than 2 cm is formed on the adjacent wall. At the same time, it is necessary to take into account how uneven the angle is, and the stronger the curvature, the more allowance is left. The edge is pressed against the wall with maximum force. In the case when wrinkles begin to form on the strip, it is necessary to make neat cuts with scissors, cutting the canvas, heading towards the fold.
• The next step will be the marking, the next strip of wallpaper on the adjacent wall will be superimposed on it. From the allowance of the first strip that has entered the second wall, measure the distance of the width of the wallpaper sheet with a decrease of 5 mm.
• Then, using the level, a vertical line is drawn on this section of the wall. Upon completion of the markup, the next sheet is glued. In order for it to be perfectly level, a guideline is taken on the drawn line.

How to glue wallpaper on the outer corner

Wallpapering on outside corners has its problems, but it's possible to avoid them if done professionally.

Attention: In order for the wallpaper to fit perfectly on the outer corner, the point from which the sheet will go is determined so that its edge goes around the corner by 3 cm.

• The edge of the sheet is pressed against the wall with maximum force. In the case of wrinkles, as well as when working with internal corners, small cuts are made.
• Along the edge of the sheet, you can tear off a thin strip of wallpaper so that only a thin edge remains. This method allows you to seam more neatly, and will make the overlap less noticeable.
• After that, using a level, a value equal to the canvas and increased by 0.5 cm is marked from the corner. The next sheet is glued along the resulting line in such a way that its edge overlaps the torn edge of the previous canvas.
• The junction is pressed through with maximum effort, the upper and lower edges of the wallpaper are trimmed by trimming, after which the sheets are rolled with a rubber roller.

How to glue wallpaper with a pattern in the corner

When a pattern with vertically arranged stripes is applied to the wallpaper, the corners will be most visible if it is distorted. And with horizontal lines, pattern violations will be visible approaching the floor and ceiling plinths.

Avoiding these problems is easy:

• Do not forget to leave an overlap on the next wall;
• hide the resulting joint in the upper part of the corner;
• glue the wallpaper in the corner of the room so that the edge of the canvas lies perfectly even with the line drawn in advance. In this case, the second edge is cut to the edge of the corner.

It is rarely possible to completely avoid distortion of the pattern, minor errors are likely to remain. But only you will know about this shortcoming. Indeed, to detect it, you will have to carefully examine all the corners in the room. Subject to all the rules, the wallpaper will be perfectly even, and the pattern will not be disturbed.

Reading time ≈ 8 minutes

- the most common type of decorative wall decoration. The technology of the process from the outside does not seem complicated, because even a beginner can apply glue to the wallpaper and stick it to the wall. Therefore, many owners decide to do such work on their own.

A beginner can easily handle wallpapering if the wall surface is sufficiently even and without obvious defects. However, the surface is not always properly prepared and leveled for finishing work. And also, often before lovers the question arises of how to properly glue the wallpaper in the corners. Here it is important to monitor the match of the selected pattern, if it is present. Therefore, in this article we will talk about a special technique for wallpapering in the corners.

Material selection

Wallpaper remains the most popular material for wall decoration in an apartment or office space. They are able to transform the room beyond recognition, hide the flaws of the interior and emphasize the dignity. What you need to know when choosing wallpaper for an apartment:

In the store, modern wallpapers are represented by a wide range of models that differ in texture, color and composition. The rarest type is liquid wallpaper, sold in the form of a ready-made solution in plastic buckets. However, we will consider the more common roll type. There are several types of wall coverings, the most popular of which are:

Each profession has its own tricks, if followed, you can achieve the fastest and highest quality results. Sticking wallpaper in the corners is a laborious process that requires compliance with some nuances:

• The corners in the room should ideally be straight and located strictly along a vertical line. However, often the rooms do not have the correct geometric parameters, so the corners must be aligned.
  
• For curved corners and walls, it is better to choose voluminous canvases made of vinyl or non-woven. The pattern should be uncomplicated, and the shade should be matte. You need to glue such wallpapers in the corners of the room to mask all the flaws.
  
• If you have uneven corners, thin paper sheets, or 3D covers with large intricate patterns that need to be adjusted all the time, will not work for you.
  
• It is best to start gluing from the window, gluing the very first sheet strictly vertically.
• If your room has even corners, it will be enough for you to process them with putty, masking minor minor irregularities.
  
• Align the corners with the help of special plastic corners, which are easy to find in any hardware store. They are securely attached to the wall with putty.
  
• It is necessary to align the corners at the stage of finishing puttying of the walls.
  
• If you decide to glue paper sheets without using an additional layer, it is worth considering the capriciousness of this material. Gluing must be done quickly so that the paper does not have time to absorb moisture from the glue.
  
• If there are sockets or switches in the gluing area, turn off the electricity in the apartment for the duration of the work. So you will avoid unpleasant situations and undesirable consequences.
  
• Do not glue the corners with a solid canvas. Before starting work, you need to make accurate measurements and cut the wallpaper into strips so that one canvas comes to the next surface by at least 20 centimeters. For example, it is quite difficult to glue non-woven wallpaper even in even corners with a solid canvas.
  
• Do not forget to coat all walls and corners with glue before starting pasting. Glue must be distributed over the entire surface, and in the corners with special care. It is believed that it is in the corners that the wallpaper most often begins to peel off and move away. Using a roller, the adhesive can be easily distributed over the entire area and perfectly prepare the surface for further finishing.
  
• In hard-to-reach places, apply glue with a special brush.

Wallpapering walls is an affordable modern means of interior decoration. Depending on the material used, you can hide some flaws and wall defects. People involved in repairs know that the wrong technology for applying wallpaper and haste lead to ugly consequences, a waste of time and effort.

Before proceeding to work, read the instructions for applying wallpaper to the walls.

What angle to start from?

Properly glued wallpaper will look perfect in the interior of the house. For work you will need:

• wallpaper;
• wallpaper glue;
• ruler;
• roulette;
• utensils for breeding glue;
• pencil;
• roller and brush (different sizes);
• soft dry cloth or wallpaper brush (to remove air bubbles);
• sharp clerical knife;
• ladder or chair.

Many recommend starting work from the door, and someone - from the window. In reality, the opposite is true. Previously, canvases were produced with a special edge for overlapping. Therefore, I had to start gluing from the far wall with a window. Now they make various types of wallpaper, it is preferable to glue them end-to-end.

In no case should you start gluing the material from the corner. Be sure to level the walls and primer. Wallpapering uneven walls is not only difficult, but in some cases impossible.

For those who prefer to glue with an overlap, the first roll should be glued from the window. If you are not confident in your abilities, it is better to start from the doorway.

The main thing is to glue the first roll, then push off from it.

Gluing rules

The industry produces a variety of types and types of wallpaper. There are painted wallpapers - non-woven. The advantage is that they can be painted in any color. An economical way of interior decoration, because the costs occur only for paint.

Wallpapering technique requires sequential actions:

• wall preparation;
• temporary removal of baseboards (if possible);
• dilution of glue according to the instructions on the package;
• lubrication of the canvas (sometimes lubrication of the wall is required);
• applying a roll to the wall from top to bottom;
• removing air bubbles and wrinkles.

The rules for sticking simple wallpaper (width 53 cm) differ from meter (width 1 meter). At first glance, it seems that meter-long materials are much harder to glue.

It turns out that this is quite simple if you understand ordinary wallpapering.

There are a number of benefits that will change your mind:

• less effort and time;
• cheaper than standard wallpaper;
• creating a seamless effect;
• high quality (made in Belgium, Italy, France);
• creating an interior for every taste.

Before buying wallpaper, be sure to calculate the expense. For this, the formula from geometry is used: (wall + adjacent wall) x 2. And remember that the length of one canvas per wall is taken with a margin of 5 cm. Always take a spare roll so that there are no flaws when you paste over door jambs and ledges. Be sure to read the length of the canvas itself on the roll in the instructions.

A prerequisite for safety is the de-energization of an apartment or house. After disconnecting, remove the top panels of sockets and switches. Starting gluing, it is necessary to clean the room from dirt and dust.

Rip off old wallpaper coverings with ordinary warm water. Wet the coatings with water using a spray bottle and wait 20 minutes, after which the wallpaper will easily move away from the walls. Remove paper with a knife or spatula. Vinyl sheets are easier to tear off by perforating.

Much harder to get rid of paint. To do this, use a grinder or drill with a special nozzle, but it is better to use chemical solutions to remove paint and varnish products.

With the wet method of removing old coatings, less dust is generated and the plaster does not peel off. After removing the old coating, it is necessary to eliminate and repair weak spots (cracks, potholes, bulges).

Be sure to level the walls and primer. Wallpapering on uneven surfaces is not only difficult, but in some cases it is impossible to carry out. Of particular difficulty for beginners in this matter is the issue of pasting external and internal corners.

Inner corner

Action technology:

1. Applying glue to the canvas or, if necessary, to the wall. Carefully grease the wall joint, as this is the most time-consuming part in the corner.
2. The canvas is glued in such a way that it extends 4-5 cm onto the adjacent wall.
3. Knowing the width of the material, stick the next wallpaper (2-4 cm) on top of the previous one.
4. Cut off the protruding parts, and glue the top material in place.

If sockets or switches are located in the corner, it is necessary to cut a round hole (smaller than the switches) from the canvas in this place.

The presence of rounded corners contributes to the formation of air voids. Be sure to make an incision in this area and glue the material tightly. More glue is applied to this area.

outside corner

The outer corner is especially noticeable in the apartment, so it needs strict accuracy.

There are 2 types of gluing external corners, depending on the unevenness of the corner:

1. If the angle is even, the canvas is glued in such a way that it protrudes 3-4 cm on the adjacent side. Next, the gluing process according to standard technology.
2. Rough walls. In this situation, the protrusion of the canvas on the adjacent wall increases (4-5 cm).

It is necessary to measure the width of the panel and retreat another 5 mm. Thus, gluing will overlap.

An incision is made in the middle of the overlap. Pushing the top of the wallpaper, remove the protruding parts of the canvas. After removing the top sheet, glue it in place.

On the convex surfaces of the wall, cuts are made, and the material is pressed tightly against the wall. These methods are designed for overlapping (for wide wallpaper). The drawings of these wallpapers are designed to hide flaws and protrusions.

For standard paper canvases, these options will not work. In this case, the first option with butt gluing is used.

If the walls are uneven

Perfectly smooth walls are a rarity. Small errors in the unevenness of the walls are acceptable, but with large deviations and noticeable curved surfaces, it is impossible to hide this when wallpapering. On the contrary, the view of the interior of the room is distorted.

In that case, if there are cracks, it is necessary to seal them with cement mortar. For minor cracks, gypsum plaster is used. Also, sticking wallpaper beautifully and with high quality will not work. The view will not match the expected results. In such cases, preparatory work must be carried out. An assistant in this will be putty.

Application rules:

• clean the surface from dirt and dust;
• tear off the old coating (if any);
• apply antibacterial impregnation;
• prime the wall;
• apply 1 layer of starting putty;
• apply a paint grid over putty (from the appearance of cracks);
• apply a second layer of putty;
• grease with two layers of finishing putty (thickness 2-4 mm);
• after complete drying, wash with a primer;
• remove all roughness and uneven surfaces with sandpaper.

How to stick models with a pattern?

Wallpapering corners is a tricky job in itself, especially for a beginner.

Monochromatic colored wallpaper is a great way out. But you can bring liveliness to the interior only with the help of a drawing. Also, in some cases, such models can cover up irregularities. Do not forget that the canvas is glued with an overlap, otherwise the pattern will add an awkward look to the interior, and all the flaws will be visible.

You can use the pattern selection method, not forgetting that the canvases are overlapped and must be cut off. The drawing should be of medium size and go strictly along the plumb line. Large or too small drawings add a distorted effect.

By selecting different colors of the canvas, you can achieve the division of the room into zones without resorting to additional costs (arches, partitions). It is important that the colors harmonize with each other.

Uneven walls and corners are found not only in the old buildings of houses, but also in modern new buildings. It is because of this defect that problems arise with interior decoration. To avoid sad consequences, you should follow the rules:

• In order for the wallpaper to hold better on the outer corners, it is necessary to press them as tightly as possible against the wall. Glue the wallpaper from top to bottom, gradually lowering to the floor, thereby avoiding the appearance of wrinkles.
• If glue gets on the front of the material, immediately remove it with a soft cloth. The front sides of some types of canvas become unusable from wallpaper glue.
• If an air bubble is found, it must be pierced. Using a syringe, inject glue and smooth.
• The inner corners of the room are the most problematic, it is in these places that peeling, swelling, tearing occurs. For effective and reliable gluing of corners, add PVA glue (10%) to water when preparing the glue. Knead the glue until smooth, so that there are no lumps.

• Make sure there are no drafts. They prevent complete and uniform drying, after which the material peels off. It is allowed to ventilate the room only after the wallpaper has completely dried. This happens within 2-3 days.
• To better paste over areas with windows and wooden openings, the canvas must be taken with a margin and allowed to dry completely. Only after that, carefully cut off the excess material with a clerical knife.
• The unevenness of the wall is not always noticeable. Only when pasting the inner and outer corners will flaws and incorrect convergence be visible. To avoid these shortcomings, immediately before work, be sure to check the curvature of the walls with the help of a building level and a plumb line.
• In the presence of thermal heating, use a thin narrow brush to lubricate the adhesive.