Sinks type tulip installation. How to install a tulip. Replacing the washbasin, installing a tulip with your own hands. Video - Tulip sink installation

Installing a sink in the bathroom is not difficult at all, even plumbers take a little for this work - the work is simple. But at the same time, this is a responsible matter - how you managed to install a sink in the bathroom directly depends not only on the appearance of the room and the convenience of using the plumbing fixture, but also on the sanitary and hygienic situation in your entire apartment.

If you remember, then quite recently in our country the problem of choosing a sink suitable for your apartment did not exist. The same type of products were in almost every bathroom. Nowadays, the variety of these products allows you to create an interior that fully meets your taste, but at the same time, a rich choice poses many questions for the owner of the home.

Types and methods of installation

The installation method of this plumbing fixture directly depends on its type. The most common include:

Hanging or console washbasin - mounted to the wall on brackets. The shape and dimensions of the device can vary greatly, it is easy to install it. But there is a significant drawback - communications remain in sight;
Built-in sink - installed in the countertop. The design hides all unsightly communications and makes it possible to use furniture with a built-in sink for storing small items. True, such a design takes up a lot of space;
"Tulip" (with a pedestal) - it is distinguished by a special pedestal on which a bowl is installed, attractive in appearance and allowing you to hide communications, which led to the popularity of this model;
The sink in the bathroom with a semi-pedestal - for such products, the pedestal is attached to the wall, it requires a sewer pipe to be connected at a certain height.

What to consider when buying a washbasin

Going for a sink, you need to accurately understand what type of sink you need. In addition, you need to know the allowable dimensions of the device and what is the required installation height of the washbasin, for which they measure the place in the bathroom where it will stand. Almost any shape of the bowl will do, the optimal length should be at least 55 cm, otherwise the water will splash around the room during use. These products are produced with holes for the faucet and deaf, for this reason, the installation method of the faucet and the appropriate size of the washbasin for the bathroom must be calculated in advance. It is better to purchase it at the same time as the sink in order to immediately test their compatibility. In addition, do not forget about the conformity of the fasteners of the device and the plumbing system.

Carrying out installation work

Before fixing the washbasin to the wall, it is necessary to determine whether it can withstand the additional weight. If in doubt, it is better to use a supporting frame to mount the device. For convenience, we immediately mount the crane,

The work of installing a sink consists of several stages:

Select the location where the device will be installed.
We draw a horizontal line corresponding to the upper part of the sink, be sure to use the building level, check its horizontalness. Places for fasteners are marked as follows - the washbasin is aligned along the line with the upper edge and after that the attachment points are marked with a marker. It must be remembered that the installation height of the washbasin should be such that it is convenient to use it.
Again we check whether the height of the washbasin is suitable for you, if necessary, change something, then it is better to do it at this stage of work. In places where there will be fasteners with a puncher, holes are made. They should be slightly smaller than the dowels used. We introduce glue into the drilled holes, for a stronger connection, and dowels are hammered into them.
Now you need to install the bowl, for this we screw plumbing self-tapping screws into the holes prepared in advance. We check the reliability of fastening and install the sink on them. After that, we put spacers on the screws, and slowly screw them in. You should not make significant efforts, otherwise the bowl may burst. Fasteners are closed with decorative caps.

After that, we can assume that the installation of the sink is over. Now you need to turn on the water and check if the installation was completed correctly. If water is leaking somewhere, then most likely you just need to tighten the connections, having previously smeared them with sealant.

There should be no gaps between the hay and the sink. The gap can cause water to enter the floor, which will ruin the finish. If there is still a gap, then the joint must be sealed with silicone sealant. The installation of the sink in most cases is not difficult. If you do all the work correctly and accurately, without neglecting what is said in the instructions, the result will certainly be positive. Competently and in a suitable place to fix the sink will extend its service life.

Types of siphons for the sink

The S-shaped corrugated hose is the simplest siphon, in theory it is enough for a simple washbasin, food residues, hygiene items or toilet paper do not get into it. But there is one caveat - during the time it moves a lot and after a short time it breaks, it is generally impossible to clean it with a cable. For this reason, if you often have to clean the sewer in the apartment, you must use a hard siphon, which has a hole with a lid for checking and cleaning it, and it is mandatory for a sink installed in the bathroom or in the kitchen.

Two types of hard siphons are made:

siphon bottle;
The pinnacle of the evolution of these products and also of the tulip washbasins is a chrome-plated decorative siphon with an inspection hole. In addition, such a device is very functional and completely hygienic. But such a siphon is much more expensive than usual.

Washbasin installation

Do-it-yourself installation of a washbasin in the bathroom is done by fixing it with dowels to the wall on special brackets.

You need to know that installing a tulip sink on a pedestal, even from the floor to the bottom of the sink - you should not consider it as a supporting element of the device! Self-tapping screws still need to be sunk into the wall surface by at least 70 mm, for this reason, self-tapping screws with a length of 100 mm or more should be used if the wall is tiled on a layer of plaster, and longer fasteners for thicker coatings. Dowels should be used propylene, metal anchor bolts are well suited. PVC fasteners crack when humidity and temperature change, metal rusts, and polyethylene fasteners have low strength.

The spacious bathrooms use a sink with a cabinet. A lot of space for such a design is necessary because dirt collects inside and under the cabinet. And the volume of the seemingly large dressing table is not too large - the main part of the space is occupied by pipes and a siphon

Sealing

Nowadays, all plumbing fixtures are sold with ready-made sealing gaskets. When installing them, you must follow a few simple rules:

Seal only on dry joints. You can dry them with a household hair dryer if you need to.
It is not advisable to take hands on the areas where the gasket will stand. Captured places - degrease by washing in water with dishwashing detergent.
Paronite gaskets - rigid, yellow gray or red, installed between a metal pipe and plastic elements.
Plastic pipes are made with a margin, they must be cut exactly to size, in the absence of experience in such work, do this only with a special pipe cutter. Even a minimal misalignment will cause joint leakage.
Before installation, rubber gaskets are treated with silicone sealant. The latter needs some explanation. Silicone and rubber gasket separately can last 3-5 years, and if they are installed together, they last an unusually long time. The reason is the difference in thermal expansion of these materials.

If you install the sink correctly, taking into account these points, then the reliability of the connections is guaranteed

Washbasin installation height

At what height the washbasin will be installed is not regulated by any documents, it is customary to install it 80-85 cm from the floor. Do what is more convenient for you - in a low family you can place it a little lower than generally accepted standards, and for tall people you can raise it. True, if you need to install a sink with a pedestal, then during installation, it will be necessary to focus on its height.

Add site to bookmarks

Kinds
Choice
Mounting
Finishing
Repair
Installation
Device
Cleaning

Features of installing a tulip sink

Many people decide to install the sink themselves at home, but first you need to choose it wisely. One of the common options is the installation of a tulip sink, it, like other options, has some features.

Drawing and dimensions of the shell-tulip.

If you already have all communications in the bathroom, then before you put the tulip sink, you need to measure the distance from the floor to the water supply point and, based on this, purchase a washbasin of a certain height. You can not select the height in the case when communications are planned to be mounted after the installation of the tulip sink is completed.

The tulip sink can have a monolithic design or consist of two parts: a washbasin and a stand.

All communications are hidden in the stand, a bowl rests on it, which is additionally attached to the wall. As a design flaw, one can call the fact that the cranes on it have a fixed height, and this is not always convenient for children.

What you need to install a tulip sink

electric drill, drills and dowels;
a special siphon with the possibility of draining the “overflow” (if it is not included in the design, it must be purchased separately);
wrenches, screwdriver, hammer;
building level;
grout (for example, Ceresit).

In order for the sink to look good in the bathroom, its color should be in harmony with the color of the washable wallpaper or tile.

Back to index

How to install a tulip sink

Before you start, you need to dismantle the old sink. It is necessary to turn off the water and disconnect the drain. After that, the sink is unscrewed from the wall with wrenches.

Now you need to prepare a place for mounting a new tulip sink. To do this, it is necessary to carefully remove the remains of cement from the walls and floor, then, according to the fasteners, holes are made in the wall. Old holes in the wall are carefully sealed with grout, which is better than cement mortar, as it dries quickly.

Everything must be done correctly so that the fasteners and holes in the wall coincide. It is necessary to install the washbasin and mark the places for its fastening; to check the correct installation, it is necessary to use the building level. The siphon is attached to the footboard with the help of special fasteners, it is necessary to use rubberized washers. First you need to properly connect the siphon, and only then connect the water. Many do the opposite, and then if your tulip is installed incorrectly, flooding cannot be avoided. To, you will need outside help. It is not necessary to tighten the nuts, as the footboard has yet to be installed. We slightly raise the bowl, put the footboard and attach the drain hose to the sewer.

When people do bathroom renovations, they try to change all the accessories.

Such actions help to achieve comfort for every day.

Washbasins are one of those items.

Now the market is full of sinks of various types and designs.

But the washbasin should not only be pleasing to the eye, but also be comfortable, practical and properly installed. In the current article, we will consider how to install a tulip sink yourself.

Tulip Wash Basin View

Tulip - shell on a pedestal

Recently, quite common washbasins in the form of a flower.

The tulip shell, in addition to the usual bowl, has a stand.

That is, the bowl stands on a leg.

That is why it has such a name.

Its general appearance resembles a flower.

The stand is made from the same material as the bowl.

Usually it is ceramics. Usually products are made in one piece.

In some varieties, it is required to connect the sink and stand to each other independently. The tulip washbasin has an elegant appearance, which is why it is quite popular.

This design is very durable, it can last up to 20 years. Ceramics is not afraid of moisture. This type of sink hides all plumbing communications well.

For example, a siphon or pipes. Therefore, the bathroom acquires an aesthetic appearance with the presence of such an accessory. The height of the washbasin is no more than 85 centimeters.

It will not take up much space and will help save space. This type of sink has almost no disadvantages, except that it requires a little more space than a regular sink.

How to choose the right sink

How to install a tulip sink with your own hands? Before proceeding with the installation, you should make the right choice of accessory.

Ultramarine sanitary ware

It will largely depend on the quadrature of the room, as well as the number of pipes and hoses. You should pay special attention to the following points:

It is better to choose a sink equipped with an overflow system. It will help to avoid problems with neighbors in an unforeseen situation.
When it is planned to repair all communications in the restroom, any version of the sink will do. But, if pipe replacement is not expected, you will have to measure the distance between the floor and the pipe. This will help you determine the height of the required rack under the sink.
In addition, it is important to guess with the width of the pedestal. It should hide all pipes from view. Therefore, the width of the pipes under the washbasin should also be measured.
Together with the sink, you need to choose a siphon, since it usually does not come with the kit. It is better to pick it up immediately on the spot, when buying a washbasin.

Now the market is filled with a huge number of models of sinks. It will not be difficult to pick up something for your bathroom.

It is important that the washbasin harmoniously fit into the interior and the overall space of the room. Ideally, it should hide all pipes from the field of view of a person.

Installation procedure

Some craftsmen are wondering how to install a tulip sink in the bathroom. This procedure does not require special knowledge and skills.

Washbasin installation

The main thing here is to follow a certain scheme of actions:

The first thing to do is prepare the instrument. Here you will need: a screwdriver, a wrench, a hammer, a drill, a level, dowels and expansion plugs.
Next, you need to find a place to fix the bolts. To do this, the accessory is applied to the surface and marks are made through the holes. Only after an accurate determination of the place can you take up the drill.
You need to attach a siphon to the drain of the tulip bowl in advance.
The sink is attached to the wall, the bolts should not be immediately tightened, it is enough just to bait. In the center of the bowl, you need to attach a pedestal, or leg. The main thing here is not to forget about the output of the corrugated drain hose into the sewer. In simple words, a drain is made.
After everything is summed up, you should proceed to fixing the accessory. To do this, the bolts must be tightened.
The joints between the washbasin and the wall should be immediately smeared with a special transparent sealant. This will help prevent water and moisture from getting in. That will prevent the formation of the fungus in the future.
And the last step is the installation of the mixer. Usually this does not present any difficulties.

After installation is completed, immediately check the accessory for leaks. To do this, you can plug the drain with a cork and draw water. A properly installed washbasin will add comfort and coziness to the bathroom.

The video shows the installation of a sink with a pedestal:

Select it and press Ctrl+Enter to let us know.

Source: http://FoxRemont.com/engineering/water/sanitary/kak-ustanovit-rakovinu-tyulpan.html

How to install a tulip. Replacing the washbasin, installing a tulip with your own hands

As a rule, a “tulip” sink is monolithic or consists of separate components - a bowl and a stand. Despite the presence of pedes

tala, often such a sink is attached to the wall using brackets or dowels. The sink can also rest on a pedestal, but in this case it is attached firmly to the wall.

How to install a tulip

If the drain fittings are not included in the kit, then it is worth buying a sink at the same time with a siphon so that the structures would

whether compatible. It is also advisable to buy a mixer at the same time as buying a sink. Almost all import

ny, and now many domestic sinks have overflow protection (“overflow” system). Water

through a hole in the upper part of the bowl through a special channel inside the ceramics flows into the siphon. You need to know that standard domestic siphons are not suitable for such sinks. Nowhere to divert water coming from the "overflow" system. Therefore, it will be necessary to purchase a special siphon in the kit suitable for such a system.

Tulip sinks have become very popular in the post-Soviet space for their pleasant appearance and ease of use.

Tulip sinks are now installed everywhere, both in small apartments and in huge Premium class cottages, and the obvious advantages of the “tulip” are the reason for this - strength, variety of assortment, durability and convenience.

But before moving on to the features of the “tulip” installation, it is worth considering in more detail what such a sink is and what its advantages are. The first thing you should pay attention to is the leg, which plays the role of a pedestal, and which takes on part of the load that falls on the sink.

It is due to this leg that this type of product got its name, for its resemblance to a flower with a thin and long stem. The installation of a tulip shell begins with the fact that water and sewer pipes are brought to its location.

The bowl of the product is installed on a pedestal, after which the places for placing the brackets or the places for placing the holes for the bolts in the wall are marked. Yes, do not be surprised, the tulip sink is installed not only on one leg, but also on a bracket, or a hidden mount inside the tulip itself. This is due to the fact that the leg will not be able to provide the necessary stability of the bowl and the entire structure may collapse under high load, or fall in any direction.

After placing and fixing the bowl, the installation of the tulip sink continues by connecting the bowl to the siphon, which connects it to the sewer, and then connecting the faucet to the water pipes with a flexible connection.

It is worth making an important reservation at this point: many violate the sequence and connect the water supply first, and then the siphon.

But in the event that some kind of gasket, or the mixer turns out to be faulty, flooding, albeit small, is inevitable, while the preliminary connection of the siphon and sewage will avoid excess moisture on the floor of the room. Connecting the tulip sink ends with the placement of the legs under the bowl, which will hide unaesthetic communications.

It is recommended to apply a layer of transparent silicone sealant at the junction of the bowl and the pedestal to increase the service life of the sanitary ware. Well, and, of course, it is not recommended to install and connect on your own, but you should invite a professional plumber. The cost of work is only 1500 rubles.

Plumbing work

The most common type of sink in modern bathrooms is the pedestal or so-called tulip sink. This floor-mounted washbasin blends in beautifully with both classic and ultra-modern interiors. In addition, among its advantages are functionality, practicality and durability.

As a rule, a “tulip” sink is monolithic or consists of separate components - a bowl and a stand. Despite the presence of a pedestal, such a sink is often attached to the wall using brackets or dowels. The sink can also rest on a pedestal, but in this case it is attached firmly to the wall.

Tulip sinks, like other types of sinks, come with a hole for installing a mixer and are deaf. For standard "Soviet" bathrooms, where the piping provides for the installation of one faucet for shower and sink, the option without a hole is more suitable.

If drain fittings are not included, then it is worth buying a sink at the same time as a siphon so that the designs are compatible. It is also advisable to buy a mixer at the same time as buying a sink.

Almost all imported, and now many domestic sinks have overflow protection (“overflow” system). Water flows through a hole in the upper part of the bowl through a special channel inside the ceramics into a siphon. You need to know that standard domestic siphons are not suitable for such sinks.

Nowhere to divert water coming from the "overflow" system. Therefore, it will be necessary to purchase a special siphon in the kit suitable for such a system.

Tulip sinks, in addition to the winning design, are distinguished by the ability to hide all communications in the leg-stand. Neatly and securely installed "tulip" does not spoil the interior of the bathroom with protruding pipes, faucets and valves.

Replacing the washbasin, installing a tulip with your own hands

When you install a tulip for the first time, you will need a guide from which you will build on doing this work.
So, let's begin! What do you need for this?

First, the tulip itself, the stem and the washbasin.

Secondly, you will need some white and Ceresit, you can use colored Ceresit, the color of a tulip.

Thirdly, you will need an electric drill or a hand drill, but you may have problems with it, also two dowels and a suitable drill for them.
Fourth, don't forget to take a sink drain. When buying a tulip, the plum is NOT included in the kit.

When choosing the color of the sink, choose a tulip to match the washable wallpaper or tile, for harmony. You should purchase everything you need and check the package, preferably in one store, so that one seller can advise you. You should also keep the receipt after the purchase, as well as after each significant purchase.

Now everything is bought and delivered to your apartment or house. After that, the old tulip or sink should be dismantled.

As a rule, first disconnect the drain by directly shutting off the hot and cold water supply taps. If the sink was bolted to the wall, then we unscrew them with a wrench, usually by 13. Next, loosen the tulip leg with our hands.

After removing the tulip and shell, you should prepare a place for installing a new tulip. Cement or Ceresit must be removed from the floor with a spatula.

Next, we prepare the wall in order to attach a new sink, if the height and distance between the tie bolts match, it doesn’t cost anything to change, if they differ, then we prepare according to the new specification.

That is, we drill holes, while removing the old ones, change the height (level), mark new places for the dowels. In order to remove old holes, they should be covered with Ceresit, which dries quickly, which will soon allow you to continue working on the sink.

Of course, it takes a day to dry completely, which should be taken into account during installation. Then we install the tulip leg and try on the sink, while the holes in the wall and on the sink should match, in this case it is better to check again before you drill.

If everything matches, then you should start assembling the siphon for the washbasin and attach it with the appropriate plastic washers, not forgetting to put insulating rubber washers. We tighten them with our hands so as not to overtighten. Now we fix the sink to the wall with tie bolts.

It is necessary to make two bolts in order to put the leg. When installing the leg, you should raise the sink, for this we did not tighten the bolts, passing the corrugated siphon hose inside the leg and bringing it out at the bottom, through a special hole.

After you install the leg, insert the drain hose through the O-ring into the sewer drain pipe.

Should fit tightly. In the event that it does not fit, then use a screwdriver or a technical knife.

Having installed the leg, you should fix the sink with tie bolts, having previously prepared the cement mortar or Ceresit mortar, after which you should walk along the contour of the leg with mortar.

If the floor is tiled, you can use a special adhesive designed for such surfaces. The washbasin can already be used immediately after its installation, but the leg must dry.

Back in the days of perestroika in our country, the tulip shell was considered a great "chic". And everyone, paying tribute to fashion, only thought about how to install a tulip sink at home. However, even today, when demand for it has fallen a little, installing such a sink provides a good and inexpensive opportunity to give our bathroom a charming look.

After all, the popularity of the tulip is associated with a practical design, which consists of a compact ceramic pedestal and the sink itself, which resembles the appearance of a flower that closes the plumbing system and allows you to give the bathroom an aesthetic look.

Since the release of the first model, a wide variety of designs have been produced, such as round built-in washbasin, oval washbasin, countertop washbasin, square countertop washbasin, etc., which can satisfy various tastes and requirements of customers.

Therefore, very often, even today, many people have the question: “how is the tulip shell installed?” The answer to this question is “yes, very simply”. And for this it is not at all necessary to invite plumbers, but you can simply get by with the services of a home assistant. Before buying, you need to take measurements correctly.

The most important thing is to measure the distance between the water supply valves and the floor. When you have made sure that all dimensions are the same, attach the sink to the wall and mark on it the places for its fastening. Now, using a drill, punch holes in the places marked on the wall and hammer dowels into them. After that, you can mount it with a leg and attach a mixer with a siphon.

Today, many designers have developed various modifications of modern, stylish bathroom furniture: cabinets, tables, bedside tables, whatnots, etc. You cannot place an ordinary, simple tulip sink in such furniture, because this requires a sink built into the countertop, for example, a round built-in washbasin or a square built-in washbasin.

But do not be discouraged - all these products are installed according to one, similar principle. Now, knowing how to install a tulip, you yourself will answer this question, which is easy.

Your thoughts on “which sink to install?” depends on your taste and desire to create an interior that will bring to your bathroom not only a comfortable and cozy environment, but also a modern, stylish atmosphere.

You can buy any sink in the online store, which presents a very wide, diverse range of different modifications and designs. Including: popular countertop sink, round built-in, oval, rectangular and more. others

How to install a tulip sink

Despite all the variety of models presented on the modern market of sanitary equipment, the tulip sink has been enjoying well-deserved popularity for many years and the demand for this model is only growing.

This type of sink is a sink with a pedestal-leg. A siphon and all unaesthetic water communications are hidden in the leg of the "tulip". Such a sink will make your bathroom more compact and elegant.

You will need

pencil, drill, dowels, bolts, mixer,
siphon for water drainage

Instruction

1 Select a sink. When choosing a new sink, it's not just the color and design that needs to be considered. To be fully equipped, before going to the store, you need to make some measurements. First, you should measure the width of the wall at the intended location of the sink. It is also necessary to take into account the distance to the water supply and sewer inlet valves, the diameter of the pipes and the height of the proposed installation.

2 Remove the old sink. Before starting dismantling, do not forget to turn off hot and cold water. Disconnect the siphon, unscrew the hoses, remove the faucet, and then the washbasin itself.

3 Place the sink body on the base without fixing it.

4 Push the new sink against the wall and mark the fixing points with a pencil.

5 Drill holes with a drill and insert dowels of the desired size.

6 Assemble the siphon and place it on the sink. Installation of a tulip sink involves assembling and installing a siphon before fixing the sink to the wall.

7 Attach the faucet to the sink. Connect the flexible hose to the installation taps. Remove communications to the base of the sink.

8 Fix the sink to the base with two screws using the sleeve.

9 Screw the sink to the wall through the holes in the attachment points and tighten with nuts and washers.

10 Connect the mixer to the pipes. Connect the siphon to the sewer. Check the connection carefully. If the connection is not made carefully enough, then after a fairly short time, an unpleasant smell may appear in the bathroom.

11 Fill the joint between the wall and the sink with silicone sealant.

Source: http://goodlinez.ru/sanitary_works/472

Tulip sink installation

In the article How to choose a bathroom sink, we already talked about the popular model of sinks, called "tulip" because of the resemblance to this beautiful flower, which gives it a long pedestal, reminiscent of a tulip stem.

The design of the sink not only looks very aesthetically pleasing in any bathroom interior, but is also very practical. Thanks to its “leg”, the sink is securely fixed and even if you lean on it, it will not fall, as the force will be transferred to the support and then to the floor.

In addition, in the pedestal (this is the correct name for the leg of the tulip sink) you can place flexible hot and cold water pipes, as well as a corrugation or siphon for draining wastewater from the sink into the sewer.

Installing a tulip sink is not particularly difficult, and you can easily perform all the necessary operations yourself if you use the tips given in this article.

Different designs of tulip shells - which one to choose?

Despite the external similarity, sinks of this type still have some differences in their design, which you should be aware of before buying.

The cheapest models have one hole for draining water and one hole for installing a faucet.

This design is the most simple and quite convenient to install and operate.
But, if you are planning to decorate the interior of the bathroom in a retro style, then you may need a sink, where, in addition to the tap hole, there will also be two holes for hot and cold water faucets. Pay attention to this.

You should also think in advance - do you need an overflow? On the one hand, it is quite convenient if you wash something in the sink, drawing water into it by plugging the outlet. This will prevent flooding in the bathroom.

But if you do not plan to regularly draw water into the sink, then you can completely do without overflow.

Moreover, its presence only complicates the system of discharge pipelines, and also creates additional inconvenience when cleaning with a plunger in case of blockage, when you have to tightly plug the overflow hole.

You also need to decide on the height of the sink, the color and design of the design. If you have decided on the design and have already bought the model you need, then you can proceed directly to the installation.

Let's see how the tulip sink is installed step by step with a photo.

Required tool

For installation you will need the following tool:

roulette;
screwdriver;
electric drill;
wrench;
open-end wrenches;
pliers;
punch;
drill for concrete;
tile drill (if there are tiles on the wall);
a hammer;
level;
silicone sealant.

Installation of a sink with a pedestal (tulip)

Installation begins with marking the places where the sink is attached to the wall. To do this, you need to put the sink on your foot and mark the holes. But before that, you need to completely assemble all the fittings attached to the sink in order to do the fitting taking into account the entire “body kit”.

Attach a faucet, flexible hoses, siphon outlets or corrugation to the sink. This will determine whether it will be convenient enough to connect to the connection points of existing water supply and sewerage networks.

The outlet is fastened through the gasket with a screwdriver, tightening the screw on the stainless steel divider grate, which serves to trap large debris. After that, a tap, outlet fittings and piping are screwed to the sink. .

A sink with fittings screwed to it is installed on the leg. In the process of trying on, it is advisable to check the horizontal installation of the rear wall of the sink using a hydraulic level.

After that, we check whether all the inlets and outlets can freely reach the points of connection. If necessary, you should immediately make adjustments - move the sink or use a different length of inlet / outlet.

After that, using a soft pencil, you should mark on the wall the location of the mounting holes in the ceramic body of the sink from the side of the tailgate. In these places, you will need to drill a wall, insert dowels into the holes made and screw in the studs that will fix the sink to the wall.

When the installation sites are marked, with the help of a core, a light blow of a hammer on the wall marks the drilling site.

If the core is not at hand, you can use a drill with a carbide tip.

If tiles are laid on the wall, be very careful not to split them. In this case, you can use the tips from the article How to drill tiles and stick thick tape at the drilling sites to prevent the drill from slipping at the beginning of drilling.

After that, you need to drill holes to the desired depth. If the wall is covered with tiles, you should first go through the tile with a special drill bit, and then continue drilling by rearranging the drill with a carbide tip and turning on the drill in shock mode.

When the holes are ready, dowels are inserted into them.

After that, using an adjustable or open-end wrench of a suitable size, you need to tighten the studs:

Everything, metal threaded studs are screwed into the wall and you can screw the sink to them.

The leg is placed at the place of installation on the floor, and the sink is installed on the leg, putting on metal studs sticking out of the wall.

The sink is fixed to the studs with nuts through elastic gaskets. The nuts should be tightened very carefully so that the faience does not burst at the attachment point from excessive force. As soon as the nut begins to go with effort, stop tightening.

In addition, when tightening the nuts, you need to tighten them in turn - a little first, then the second, then again a little first, then again a little second, and so on. The same method of tightening the nuts is used when installing the toilet bowl - it is fixed to the floor in exactly the same way by tightening the nuts one by one.

This allows you to more evenly distribute the resulting forces in the body of a fragile plumbing fixture and prevent the appearance of cracks.

Special caps are put on the nuts to prevent debris from entering and preventing metal corrosion. Under the caps, you can smear a little grease. In this place, no one will see him, and if necessary, remove the sink, the nuts can be easily unscrewed even after a year, as if you screwed them yesterday.

After attaching the sink to the wall, you can begin to connect the flexible supply and outlet fittings to the existing water and sewer networks.

Connection to the cold and hot water supply is carried out through a ball valve (or valve) for the possibility of promptly turning off the water if necessary.

It is very convenient to use corner taps that are mounted on the wall at the exit of the pipes and look very aesthetically pleasing.

The last step in installing the sink is to fill the gaps with silicone sealant. The popular "Sanitary" sealant, which is available both in the form of a transparent filler and in white, is quite suitable.

The gaps between the back side of the sink and the wall, as well as around the perimeter of the pedestal at the place where the “legs” of the sink are installed on the bathroom floor, are sealed with a sealant. Below you can watch a video of installing a tulip sink (click on the triangle to play): shells does not represent and you can always do it yourself.

Self-installation of a sink and a tulip, ways of attaching a moidodyr to a wall

Types and methods of installation

The installation method of this plumbing fixture directly depends on its type. The most common include:

Hanging or console washbasin - mounted to the wall on the brackets. The shape and dimensions of the device can vary greatly, it is easy to install it. But there is a significant drawback - communications remain in sight;
Built-in sink - installed in the countertop. The design hides all unsightly communications and makes it possible to use furniture with a built-in sink for storing small items. True, such a design takes up a lot of space;
"Tulip" (with a pedestal) - it is distinguished by a special pedestal on which a bowl is installed, attractive in appearance and allowing you to hide communications, which led to the popularity of this model;
A sink in a bathroom with a semi-pedestal - for such products, the pedestal is attached to the wall, it requires a sewer pipe to be connected at a certain height.

What to consider when buying a washbasin

Almost any shape of the bowl will do, the optimal length should be at least 55 cm, otherwise the water will splash around the room during use. These products are produced with holes for the faucet and deaf, for this reason, the installation method of the faucet and the appropriate size of the washbasin for the bathroom must be calculated in advance.

It is better to purchase it at the same time as the sink in order to immediately test their compatibility. In addition, do not forget about the conformity of the fasteners of the device and the plumbing system.

Carrying out installation work

The work of installing a sink consists of several stages:

washbasin fixture

Select the location where the device will be installed.
We draw a horizontal line corresponding to the upper part of the sink, be sure to use the building level, check its horizontalness.
Places for fasteners are marked as follows - the washbasin is aligned along the line with the upper edge and after that the attachment points are marked with a marker. It must be remembered that the installation height of the washbasin should be such that it is convenient to use it.
Again we check whether the height of the washbasin is suitable for you, if necessary, change something, then it is better to do it at this stage of work. In places where there will be fasteners with a puncher, holes are made. They should be slightly smaller than the dowels used. We introduce glue into the drilled holes, for a stronger connection, and dowels are hammered into them.
Now you need to install the bowl, for this we screw plumbing self-tapping screws into the holes prepared in advance. We check the reliability of fastening and install the sink on them. After that, we put spacers on the screws, and slowly screw them in. You should not make significant efforts, otherwise the bowl may burst.
Fasteners are closed with decorative caps.

The installation of the sink in most cases is not difficult. If you do all the work correctly and accurately, without neglecting what is said in the instructions, the result will certainly be positive.

Competently and in a suitable place to fix the sink - it means that it will extend its service life.

Types of siphons for the sink

The S-shaped corrugated hose is the simplest siphon, in theory it is enough for a simple washbasin, food residues, hygiene items or toilet paper do not get into it.

But there is one caveat - while cleaning the sewer with a plunger, the corrugation moves strongly and breaks after a short time, it is generally impossible to clean it with a cable.

For this reason, if you often have to clean the sewer in the apartment, you must use a hard siphon, which has a hole with a lid for checking and cleaning it, and it is mandatory for a sink installed in the bathroom or in the kitchen.

Two types of hard siphons are made:

siphon bottle;
The pinnacle of evolution of these products and also of tulip washbasins is a chrome-plated decorative siphon with an inspection hole. In addition, such a device is very functional and completely hygienic. But such a siphon is much more expensive than usual.

Washbasin installation

Do-it-yourself installation of a washbasin in the bathroom is done by fixing it with dowels to the wall on special brackets.

: Bathroom sink DIY installation. Education

Sealing

Nowadays, all plumbing fixtures are sold with ready-made sealing gaskets. When installing them, you must follow a few simple rules:

Seal only on dry joints. You can dry them with a household hair dryer if you need to.
It is not advisable to take hands on the areas where the gasket will stand. Captured places - degrease by washing in water with dishwashing detergent.
Paronite gaskets - rigid, yellow gray or red, installed between a metal pipe and plastic elements.
Plastic pipes are made with a margin, they must be cut exactly to size, in the absence of experience in such work, do this only with a special pipe cutter. Even a minimal misalignment will cause joint leakage.
Before installation, rubber gaskets are treated with silicone sealant. The latter needs some explanation. Silicone and rubber gasket separately can last 3-5 years, and if they are installed together, they last an unusually long time. The reason is the difference in thermal expansion of these materials.

If you install the sink correctly, taking into account these points, then the reliability of the connections is guaranteed

: Washbasin sealing options

Washbasin installation height

installation will help you figure out this issue

: Washbasin installation - video tutorial

: How to install a washbasin with a cabinet with your own hands

We have already talked about the popular model of shells, called "tulip" because of the resemblance to this beautiful flower, which gives it a long pedestal, reminiscent of a tulip stem.

Installing a tulip sink is not particularly difficult, and you can easily perform all the necessary operations yourself if you use the tips given in this article.

Different tulip shell designs - which one to choose?

Despite the external similarity, sinks of this type still have some differences in their design, which you should be aware of before buying.

The cheapest models have one hole for draining water and one hole for installing a faucet.

This design is the most simple and quite convenient to install and operate.

But, if you are planning to decorate the interior of the bathroom in a retro style, then you may need a sink, where, in addition to the tap hole, there will also be two holes for hot and cold water faucets. Pay attention to this.

But if you do not plan to regularly draw water into the sink, then you can completely do without overflow. Moreover, its presence only complicates the system of discharge pipelines, and also creates additional inconvenience when cleaning with a plunger in case of blockage, when you have to tightly plug the overflow hole.

You also need to decide on the height of the sink, color and design.

If you have decided on the design and have already bought the model you need, then you can proceed directly to the installation.

Let's see how the tulip sink is installed step by step with a photo.

Required tool

For installation you will need the following tool:

roulette;
screwdriver;
electric drill;
wrench;
open-end wrenches;
pliers;
punch;
drill for concrete;
tile drill (if there are tiles on the wall);
a hammer;
level;
silicone sealant.

Installation of a sink with a pedestal (tulip)

Installation begins with marking the places where the sink is attached to the wall.

To do this, put the sink on your leg and mark the holes.

But before that, you need to completely assemble all the fittings attached to the sink in order to do the fitting taking into account the entire "body kit". Attach a faucet, flexible hoses, siphon outlets or corrugation to the sink. This will determine whether it will be convenient enough to connect to the connection points of existing water supply and sewerage networks.

The outlet is fastened through the gasket with a screwdriver, tightening the screw on the stainless steel divider grill, which serves to trap large debris.

After that, a faucet, outlet fittings and connections are screwed to the sink.

The leg (pedestal) of the sink is placed against the wall where the sink will be located.

A sink with fittings screwed to it is installed on the leg. In the process of trying on, it is advisable to check the horizontal installation of the rear wall of the sink using a hydraulic level.

When the installation sites are marked, with the help of a core, a light blow of a hammer on the wall marks the drilling site.

If the core is not at hand, you can use a drill with a carbide tip.

When the holes are ready, dowels are inserted into them.

After that, using an adjustable or open-end wrench of a suitable size, you need to tighten the studs:

Everything, metal threaded studs are screwed into the wall and you can screw the sink to them.

The leg is placed at the place of installation on the floor, and the sink is installed on the leg, putting on metal studs sticking out of the wall.

There are several options for classifying shells of this type. The following characteristics can be taken as a basis.

According to the location of the sink

Ordinary. The most common modification of the tulip sink, which is installed against the wall. A wide range of similar models allows you to choose the option that is ideal for any bathroom.
Corner. As the name implies, these structures are designed to be installed in the corner of a room. Such plumbing, usually having small dimensions, allows rational use of usable space, ideal for arranging miniature bathrooms. We have more ideas on choosing a small sink.

Corner models have an ergonomic design.

Ergonomic model of a corner washbasin with a pedestal, additionally equipped with functional cabinets, which allows you to optimally use the usable area of the room

A corner washbasin cannot be structurally installed along a wall, while a straight model can be easily placed in a corner, fixed along one of the walls.

According to the design features of the models

According to the characteristic features of the design, three main groups of washstands can be distinguished:

monolith;
compact;
half tulip.

Monolithic models are a holistic design in which the sink is inextricably connected to the leg. Such options are quite rare in the consumer market: they are difficult to manufacture, which also affects the cost of such products.

Much more often on sale you can find washbasins of the “compact” type, consisting of two components: a sink bowl and a support column.

The advantages of these models include affordable price, practicality and ease of use. If, when the siphon is clogged, the monolithic model will have to be moved as a whole, then to eliminate this problem for the compact, it is enough just to move the pedestal.

Modifications with a leg that does not reach the floor are called "semi-tulip". They have a more modest appearance, but they have certain advantages.

Advantages of the third type of models:

such products can be mounted at the desired height, which provides additional comfort during their operation;
a half-tulip sink installed in the bathroom greatly facilitates cleaning of the room, since the floor under it remains completely free;
a semi-column, like a full-fledged pedestal, closes all communications well;
this option is well suited for suspended plumbing, however, in this case, additional installation is required to firmly fix the model.

A washbasin with a semi-pedestal will look great in a compact bathroom, it is also often used when decorating office space in offices or enterprises.

According to the material of manufacture

The material from which the sinks are made affects the decorative and functional qualities of the models, as well as their cost.

Designer version of porcelain tulip sink. Such a product can become a real decoration of a luxurious bathroom.

The most common options include the following:

Faience. A common and affordable material, which is often used for the production of plumbing. Despite the budgetary price of faience tulip shells, they have good performance properties, are quite strong and durable.
Porcelain. A rather expensive option is often used for the manufacture of designer models. Porcelain products translucent in the sun have an exquisite noble appearance, however, in terms of consumer qualities, they are close to faience structures.
Acrylic. An artificial material with many useful qualities. Acrylic structures have a budget cost and a fairly low weight; they are hygienic and impact resistant. In addition, this plastic is easy to process (grind, engrave) and color, which allows you to create the most incredible options for tulip shells. Among the shortcomings, some fragility (the material is easily scratched) and flammability can be noted.
A rock. A strong and durable material from which impressive washbasin variants can be made. Most often, granite and marble or more affordable artificial stone are used for this. In addition to the high cost, the main disadvantage of such models is their heavy weight: it not only makes manipulation difficult, but also gives a heavy load on the floor. We recommend that you familiarize yourself with stone sinks in more detail.

In addition to the above options, there are tulip shells made of glass, various types of plastics and other materials.

In addition, tulip shells vary in size. Typical options are models with a bowl size of 50-70 cm, however, there are miniature and large-sized modifications.

Pros and cons of a tulip sink

Wash basins with a pedestal have a large number of important advantages:

Large range of models. On sale there are various modifications that differ not only in design features, but also in design, color, size. Thanks to this, you can always choose the option suitable for the interior of a different stylistic orientation.
Affordable cost. The cost of a "tulip" mainly depends on the material from which it is made. However, ceteris paribus, the price of this type of washbasin is somewhat lower than for other models (for example, “moidodyr”).
Compact design. Even conventional modifications have relatively small dimensions, which allows them to be installed in fairly compact rooms. In addition, there are miniature models - corner tulip shells and options with a semi-pedestal. At the same time, even small-sized structures can effectively remove service communications (water and sewer systems) from the eyes.

The tulip shell is practically devoid of flaws. Some inconvenience can be considered the impossibility of using the space under the washbasin (for example, under the bedside tables).

However, there are models that provide additional cabinets and shelves that are attached to the column.

Compared to other types of plumbing, the installation of a washbasin with a pedestal is quite easy. It is only important to attach the bowl to the wall, as well as correctly assemble the mixer and siphon. All this can be done with your own hands without the involvement of specialists.

You should also take into account the features of models made from different types of materials (porcelain structures are fragile, stone structures are heavy, and so on).

When choosing a model, it is important to pay attention to the following factors:

Support column height. Its length should be such that a person does not have to bend over much when washing. Typical size is 70-80 cm; if it does not fit, it is better to look for another model or stop at a tulip shell with a semi-pedestal. In another article, we took a closer look at sink height standards.
The size and depth of the bowl. The best option is a sink with a width of 55-65 cm. A large modification will take up a lot of space, and from a smaller splash, during washing, they will scatter around. It is also not very convenient to wash from a very shallow bowl, it is better to choose a deeper sink. We talked about the dimensions of the sink in more detail in this material.
Mixer holes. Depending on your preferences, you can choose a model that includes one modern mixer or separate faucets for hot and cold water.
The presence of an overflow. The function prevents the bathroom from flooding when the outlet is clogged. It should only be remembered that overflow requires a special siphon and an additional non-standard pipe.
Accessories. Since pedestal washbasins usually do not include drain fittings, they will most likely have to be purchased separately. It is better to immediately pick up a tulip sink, siphon and mixer made by the same company.
Compliance with the size of the wash basin service communications. If a tulip sink is purchased to install it in a bathroom after a major overhaul with the replacement of water and sewer pipes, absolutely any option will do. When choosing a washbasin to replace previous sanitary ware, it is important that it matches the remaining communication systems.

Before going to the store, it is advisable to measure and record the distance from the floor to the supply of water pipes and other communication parameters.

Unfortunately, the discrepancy between the conclusions provided on the model and the existing wiring is very difficult, and often impossible to correct. In this case, it is better to return the model that did not fit back to the store.

Before installing a tulip sink, it is important to carefully study the scheme of a particular model, which can have different sizes and design features.

After the purchase, do not forget to check the availability of all the parts of the kit, and only then proceed with the installation of the washbasin.

Detailed installation instructions for the tulip sink

For plumbing work you will need the following tools and materials:

roulette;
perforator drill;
level for leveling the bowl;
a hammer;
adjustable wrench;
drills for concrete and tiles (if ceramic tiles are available);
dowels for fastening;
adhesive sealant;
soft pencil/marker.

To create tight joints, you will need tow or fum tape.

The following selection of photos will help you briefly familiarize yourself with the sequence of work on installing a tulip-type sink:

Image gallery Photo from Step 1: Marking the position of the sink on the wall Step 2: Marking the points for installing the brackets Step 3: Drilling holes for the brackets Step 5: Screwing the brackets into the dowels Step 5: Fixing the sink bowl to the brackets Step 6: Installing and connecting the faucet Step 7: Connecting the device to the sewerage system Installing the supporting and decorative leg

Stage # 1 - dismantling the old washbasin

First of all, you should disassemble and take out the old plumbing. For this you need:

Shut off the main water supply.
Unscrew the nuts on the faucet and disconnect the flexible or rigid piping, and then remove the faucet.
Go to the drain: unscrew the nuts on the siphon and remove it.
Remove the old washbasin from the fixtures, making room for the new one.

After that, you should check or re-prepare all communications connections: cold and hot water outlets, sewerage. Their location should match the holes on the newly purchased plumbing.

After that, you can proceed to the main stage of work.

Step #2 - Install Stopcocks and Bowl

Tulip installation is carried out in several stages.

It is best to start work by installing stopcocks. For insulation and connection strength, it is desirable to wrap fum tape or tow on their threaded part, mixed with a small amount of oil paint, which guarantees improved protection against water leakage.

After that, we proceed directly to the installation of the plumbing kit.

Leveling the bowl is a very important step in installing a pedestal washbasin. After that, also with the help of a level, marks are applied to place the brackets on which the upper part of the structure will be suspended.

To determine the places of fasteners, we put a support column on which we put the bowl without fixing it. It is important to level the structure with a level, and then mark the places for attaching the sink on the wall with a pencil or marker.

According to the marks with an electric drill, we drill holes, the diameter and depth of which correspond to the dowels prepared in advance. If the wall is finished with ceramic tiles, drilling must be carried out very carefully using a special drill.

Using a hammer, we expose the dowels into the holes made, into which we carefully and carefully screw the brackets. It is important to ensure that their position is strictly perpendicular to the wall.

To attach the sink to the wall, you need to drill holes for the dowels with a drill. Brackets are installed in them, on which the bowl is hung

We hang the washbasin bowl, while we bait the nuts through plastic or rubber gaskets.

We have more detailed step-by-step instructions for attaching the sink to the wall on our website.

Stage # 3 - connection to communications

After that, you need to deal with communications. We plug the drain hole with a return corrugated hose, which prevents the flow of water. Then, without fixing, we insert a metal drain cylinder into the hole.

We connect the washbasin to the wiring. In this case, the main drain is fixed without fail with gaskets on the outer and inner sides. Only after that the connection is twisted, but in no case is it tightened in order to avoid mechanical damage to the bowl.

Installing the mixer. It is important to consider that the diameter of its part immersed in the sink must correspond to the size of the “tulip” hole intended for this purpose. We recommend that you look at the detailed instructions for installing the faucet on the sink.

Proper installation of shut-off valves allows you to adjust the correct operation of the mixer when opening and closing the valve using an angle clamp on the rod

We install shutoff valves. We take into account that when the rod is pulled out of the mixer, the valve closes, while when the rod is stuck all the way, it is open. Adjustment of the opening and closing of the valve is carried out using an angle clamp on the rod.

At the ends of the flexible water hoses there are nuts with which the mixer is connected to cold and hot water. We check the operation of the system, inspecting the structure for leaks.

Stage # 4 - installation of the pedestal column

We close the communications with a hollow support column, doing the work as carefully as possible so as not to accidentally damage the pedestal.

Installation of a hollow pedestal, which securely covers all communication systems (sewerage, cold and hot water supply), and also ensures the strength and reliability of the structure

We process all seams with sealant in the color of the wall, plumbing or transparent colorless. After that, the installation of the tulip sink can be considered complete.

The final stage of work: filling the joints with a colorless sealant that prevents water from entering cracks and gaps, guaranteeing improved waterproofing

It should be noted that in some cases it is more expedient to first connect the mixer, and only then install the bowl on the brackets.

In addition, depending on the communications connected, it is sometimes better to replace the corrugated hose with siphons of a different type (specific information is usually available in the instructions for purchased plumbing). We recommend considering the types of siphons for the washbasin, their pros and cons, and recommendations for choosing.

Features of installing a sink with a semi-pedestal

The installation of a compact model of this modification is carried out similarly to a conventional tulip sink, but it has some features:

First of all, you should choose the right height for mounting the bowl. The standard parameter is 75-80 cm, but it is better to take into account the convenience of using the washstand.
According to the instructions above, holes are drilled in the wall, dowels are inserted and the brackets on which the bowl is suspended are fixed.
After that, the standard procedure for connecting the mixer and siphon to communication systems is performed.
Additionally, marking is carried out for fastening the semi-pedestal; in the lower part of the structure, you also need to make holes, hammer in the dowels and fix this part so that it covers the pipes.

The difference in the installation of a half-tulip lies in the last point, since the leg of the sink, which does not reach the floor, cannot give the structure the necessary strength and stability.

To install an attractive “semi-tulip” model, which will fit perfectly into a small bathroom, you need to fix not only the bowl, but also the truncated leg to the wall

Typical mistakes during installation of the structure

In order not to violate the performance of the equipment during installation, we will consider what errors should be feared.

Among the shortcomings that are often found during self-installation of a tulip sink are the following defects:

Shell tilt. If you mark on the wall and install the fasteners without level control, the bowl may not be hung unevenly. A sink skewed to one side, of course, will not decorate the bathroom too much. Correcting this defect is quite difficult: you will have to dismantle all the parts again and re-drill the holes, carefully checking with the level.
The gap between the bowl and the wall. The edge of the washbasin should fit snugly against the wall or partition. If even a small free space remains between them, water will constantly flow into it, which will sooner or later affect the safety of the wall. To avoid this, after installing the structure, it is necessary to carefully seal all cracks and gaps.
Water or sewer leak. A water or sewer leak can have dire consequences, including flooding an apartment (your own or your neighbors). Most often it happens due to poorly tightened threaded connections. After performing such operations, you need to check the connections by giving water under high pressure.
The "stirring" of the shell. The tulip sink bowl may be unstable due to loose bolts or an uneven floor under the pedestal. In the first case, the problem can be solved quite easily: you just need to check and fix all the connections of the parts. The situation is somewhat more complicated if the second reason is identified.

You can temporarily correct the situation by placing suitable gaskets under the washbasin leg (preferably silicone, not peeking out from under the structure).

For large irregularities, it is better to level the floor using a cement mixture.

There is another installation instruction on our website that describes the process of installing a washbasin with a pedestal.

Sink tulip and her choice

The Tulip sink with a beautiful name consists of two elements: a pedestal and the washbasin itself. The pedestal is necessary in order to support the sink, to take on the entire load. The pedestal also has an aesthetic function: it hides sewer pipes, a siphon and other not-so-pretty details. The tulip will make the bathroom more compact, give the interior a certain prestige and respectability. Also, due to its aesthetic qualities, such a sink will emphasize any layout in a favorable light.

When choosing a Tulip sink, you need to focus on the size of the room, that is, your bathroom. It is also necessary to take into account the location of sewer pipes and other plumbing equipment. You also need to take into account the distance to the supply of sewer pipes from the floor level and the width of the pedestal itself.

In some cases, you will also have to buy drain fittings; as a rule, they are not included in the kit. It is very good if the equipment has an overflow system. This will protect you from emergencies and minimize the risk of flooding your neighbors from below.

If the plan includes a major overhaul, in which you will completely change the pipeline, channels, connections, and so on, then there is no significant difference - just buy the option you like best. But do not forget, before making a purchase, measure all the distances so that the Tulip sink fits you in size and looks concisely in the restroom.

Tulip washbasin installation

The design is simple and does not include complex elements. Therefore, installing a tulip sink in the bathroom will not be difficult, it does not require special professional knowledge or skills. Let's describe everything in order.

First of all, we need to prepare the tools that we will need. This is a screwdriver, keys, a drill, and if there is also a drill, a hammer, plugs, a level and a dowel.

After everything you need is ready, we start marking the place where we will make holes in the wall. Please note that they must clearly correspond to the holes in the pedestal. With the help of the holes made, fasteners for the tulip sink will be carried out.

After that, we fix the siphon on the bolts to the rack. On the wrong side of the siphon, a mesh with a special gasket is attached. In this case, it is necessary to achieve a high degree of tightness.

The next step is to install the tulip bowl itself, which is carried out on the tie bolts. And then we mount the pedestal in the center of the bowl. Don't forget about the outlet of the siphon hose. This corrugated hose is discharged into the drain pipe using a special technique.

After the bowl and pedestal are installed, we proceed to fix the entire structure to the wall. Fixing and final fastening is carried out using washers and bolts.

To achieve the tightest connection between the Tulip shell and the wall, as well as to minimize the possibility of leaks, you can treat all joints with a transparent silicone sealant.

And the final stage of installation is connecting the mixer to the sewer pipe system. If you follow these instructions and do everything right, installation will not take you much time.