Blowing from a metal door what to do. Let's not let a draft into our house! Do-it-yourself insulation of the front door. Algorithm for performing the repair process

We warm

This article contains all the information on what to do if it blows from the front door, and how to prevent the possibility of drafts when installing a new one.

If the source of drafts in your house or apartment is the front door, you are unlikely to be satisfied with such a solution to the problem, which is shown in the picture above. It is no less inconvenient to curtain them with old blankets, creating a barrier to cold air.

Only a sealed front door can allow you to feel comfortable in your own home, which will not allow cold air or extraneous noises and smells from the street to enter inside. But how to achieve this?

There are several options for solving the problem:

Glue a seal around the perimeter of the canvas.
Fully insulate the canvas by sheathing it so that the material covers the gap between the box and the base.
Completely replace the canvas.

If you are just building your house, you can immediately make sure that this question never arises before you. All openings must be closed immediately.

This problem is especially relevant in suburban housing, since there the front door often goes directly to the street or to a cold unheated vestibule. Although in an apartment building a draft from the door is a very unpleasant phenomenon, even if the entrance is warm. After all, together with him, cigarette smoke and other unpleasant odors enter the apartment.

Traditional sealing is gluing a self-adhesive seal in the form of a rubber band around the perimeter of the box. Unfortunately, this method is not very reliable.

So:

First of all, with the active operation of the structure, the sealant quickly becomes unusable and must be changed.
Secondly, the slightest distortion will lead to the fact that the seal will not fit snugly against the door and will not be able to perform its function with high quality.

In addition, it is possible to glue a strip of sealant correctly only if the door is perfectly level. If there is an excellent distance between the leaf and the frame in different places, the rubber band will not fit snugly to all parts of the door.

With this arrangement, the sealing tape will provide better tightness of the door even if it is deformed and sagging, as it will have a greater degree of freedom. Whatever the initial position of the base relative to the box, the sealant will work to suppress drafts precisely because of its advantageous location.

Instead of traditional self-adhesive tape, you can use round-section polyethylene foam sealing tape or a rubber tube made of a material resistant to aggressive media for this purpose.

This is what the inlet hermetic structure looks like

And do not be confused by the lack of an adhesive base on them: in this case, glue will help you out perfectly Moment:

Lubricate the frame around the entire perimeter with glue in the place where the seal should be located.
Cut the tape to the desired length, cutting the edges at a 45 degree angle to fit at the corners.
Lubricate the side of the seal with which it will be glued with glue.
After holding time, which for Moment glue is 15 minutes, close the door and apply a rubber band to the end of the box in such a way as to ensure its tight fit. Press it down with your hands for a few seconds.

This article contains all the information about what to do if it is blowing from the front door, and how to prevent the possibility of drafts when installing a new door.

Only a sealed front door can allow you to feel comfortable in your own home, which will not let in not only cold air, but also extraneous noises and smells from the street.

But how to achieve this?

There are several options for solving the problem:

Glue a seal around the perimeter of the canvas.
Fully insulate the canvas, sheathing it so that the insulation covers the gaps between the box and the canvas.
Completely replace the canvas.

If you are just building your house, you can immediately make sure that this question never arises before you.

Eliminate drafts from an existing door

This problem is especially relevant in suburban housing, since there the front door often goes directly to the street or to a cold unheated vestibule.

Although in an apartment building a draft from the door is a very unpleasant phenomenon, even if the entrance is warm. After all, together with him, cigarette smoke and other unpleasant odors enter the apartment.

Traditional sealing is gluing a self-adhesive seal in the form of a rubber band around the perimeter of the box.

Unfortunately, this method is not very reliable.

Firstly, with the active operation of the door, the seal quickly becomes unusable and has to be changed.
Secondly, the slightest misalignment will lead to the fact that the seal will no longer fit snugly against the door and perform its function efficiently.

In addition, it is possible to glue a strip of sealant correctly only if the door is perfectly level. If there is a different distance between the canvas and the box in different places, the rubber band will not fit snugly to all parts of the door.

With this arrangement, the sealing tape will provide better tightness of the door even if it is deformed and sagging, as it will have a greater degree of freedom.

Whatever the initial position of the canvas relative to the box, the sealant will work to suppress drafts precisely because of its advantageous location.

Instead of the traditional self-adhesive tape, you can use round-section polyethylene foam sealing cord or rubber tube made of resistant rubber for this purpose.

And do not be confused by the lack of an adhesive base on them: in this case, Moment glue will help you out perfectly.

Lubricate the frame around the perimeter with glue where the seal should be.
Cut the ribbon to the desired length, cutting the edges at a 45 degree angle for joining at the corners.
Lubricate the side of the seal with which it will be glued with glue.
After exposure, which for the glue Moment is 15 minutes, close the door and apply a rubber band to the end of the box in such a way as to ensure its tight fit to the door. Press it down with your hands for a few seconds.

Attention! It takes a day for the glue to dry completely, so try to use the door carefully on the first day.

Of course, this method also has its drawbacks - the seal can be torn off by accidentally hooking it with something. But it will not be difficult to correct the situation by re-gluing it in its place.

As mentioned above, if it blows from the front door, it can be completely insulated, making sure that the insulation is slightly larger than the box and covers all the existing gaps.

For this, rollers are specially made, which are attached around the perimeter of the door leaf.

Sometimes these rollers are attached to the door frame. You will understand what is at stake if you look at the photo on the side.

And how to insulate the door, you can read in more detail in other materials on the site. This may also be required if you have an old wooden door, the canvas of which has dried out and through cracks have formed in it.

If the front door is blowing despite your best efforts, make sure that cold air is not getting in through the large keyhole. Otherwise, you will just have to replace the door.

How to prevent drafts from the door

Experienced builders know that the front door to a house or apartment can only be installed after all “wet” work is completed - laying partitions, plastering, puttying, whitewashing, etc.

Especially if it is a wooden door, which is sensitive to high humidity.

When all this work in the new house is completed, and you go to order a new door, think over your requirements for it in advance. It is clear that it should be strong and reliable, but when it blows from the front door, there is little pleasant in this.

Therefore, do not forget to clarify how its sealing will be ensured.

Now there are new models of entrance doors, the boxes of which have a special configuration - a three-stage one.

An additional ledge does not let cold air, dust, moisture and foreign odors into the room.

This configuration has the entire door frame, including the threshold, which is not mounted separately, but is integral with the door frame.

Installing such doors will save you from having to think about how to eliminate drafts.

For some families, the onset of cold weather is a real test. Even during the heating period, gaps in the windows and the front door make the residents constantly cringe. The main cause of tangible discomfort is an unpleasant and ubiquitous draft. It occurs in the case of leaky installation of doors and windows. Particular attention should be paid to how tightly the front door is installed. In this case, there are two options for solving the problem: dismantle the door and insulate the canvas, or try to insulate the door without dismantling. If the first option can be done on your own (subject to some skills and dexterity), then insulate the installation door important to produce everyone can do it with their own hands without dismantling from the box. In this article, we present our recommendations on how to do this correctly.

The main reason for the presence of a draft lies in the incorrect installation of the door frame in the opening. Most often, the installation of the structure is carried out on uneven walls, with some deviation from the level. Existing gaps are not filled with mounting foam or are filled with errors. As a result of all this, some people try to get rid of the draft and close the gaps in all available ways: to fill the holes with material, a blanket. We admit that this option is not only ineffective, but also, to put it mildly, visually inexpressive. In order to permanently get rid of the annoying draft and subsequently live in a living room with maximum comfort, it is necessary to produce high-quality door insulation. By the way, this will not only prevent cold air from getting inside, but also prevent the accumulated heat from escaping and significantly increase sound insulation. If your apartment is located in close proximity to a garbage chute, and neighbors often go out to smoke on the landing, a lot of unpleasant odors enter the room along with a draft. Insulating the door will help solve this problem once and for all.

As mentioned above, the insulation of the front door can be done in various ways. The most cardinal of them is the complete dismantling of the old door and replacing it with a new one. In this case, at the time of installation, it is important to properly install the door, taking into account all the requirements and recommendations. The second way is to insulate the internal cavity of the front door or sheathing its inner part in the absence of a cavity in the leaf or the impossibility of opening it (as, for example, it often happens in Chinese-made entrance doors). This option involves removing the door from the box. You can do the insulation yourself, but this work will not be simple and affordable for everyone. Finally, the third option is the most affordable. It will suit most families - door insulation around the perimeter. Such door insulation can be done by hand. In addition, the described method is much cheaper than the other two options. In this regard, we will describe the last option in more detail.

Do-it-yourself insulation of the front door

We hope that from the first part of the material you have understood that the main cause of drafts are cracks. They should be disposed of by pasting the door leaf with a special insulation around the perimeter. Moreover, this can be done both along the entire contour, and in separate parts. What to choose? The answer depends on personal preference and operational features. If the door is opened and closed many times a day, the increased wear is likely to cause damage to the seal. It can be easily damaged by outer clothing, objects brought into the room and other objects. Before making a decision regarding the complete insulation of the door leaf around the perimeter, it is necessary to make sure that the hinges are not sagging, and the door opens smoothly and completely. Skews also negatively affect the seal - it will touch the slopes or the floor. In view of the above, the most practical option seems to be gluing the space between the door leaf and the threshold with a heater.

What heater to choose? Best of all, a special self-adhesive tape or a polyethylene sealing cord is suitable for gluing the bottom of the door frame. In some cases, self-adhesive gum and a rubber tube will do. The heat and sound insulation characteristics of the last two options look much better. The only thing to consider: the width of the space between the bottom of the door leaf and the threshold. So, too thick a sealant may not fit in width. For the most part, the adhesive base of self-adhesive heaters is mediocre. It is best to use instant glue.

How to properly insulate your front door

The process is not complicated. Anyone can deal with it. In general, it consists of five stages.

Coating the perimeter with glue. It must be applied to the underside of the door leaf and the upper side of the threshold.
Heating preparation. The material should be measured and cut into pieces of the desired size. The ends on both sides must be bent in the form of an angle of 45 degrees.
Applying glue to the insulating layer of the insulation. No need to overdo it. Either a thin strip or dots at an equidistant distance.
Bonding insulation. This should be done approximately 10-15 minutes after applying the adhesive. After that, the insulation must be pressed tightly to the surface, tightly close the door and hold it for a while. Enough 10 minutes.
During the day, try to operate the front door to a lesser extent. It is considered that the period of full bonding lasts for 24 hours, depending on the manufacturer of the adhesive. Make sure that the seal does not move.

During the operation of the door, periodically pay attention to the condition of the insulation. It may wear out over time. However, it is not difficult to re-insulate. Fortunately, this work does not take much time, and consumables are available and inexpensive. If, after gluing the bottom of the canvas, it was not possible to get rid of the draft, it is worth trying to insulate around the entire perimeter. At the same time, depending on the design device, two options can be combined: glue the insulation to the door frame or canvas. Another likely and quite common cause of a draft is a keyhole.

Let's summarize. The described algorithm and the recommendations made in the article relate to the simplest and least expensive way to insulate the front door. If you want to do the work more thoroughly, we draw the attention of the owners of the metal front door to. It is always worth remembering that before proceeding with the insulation of the front door, you should soberly assess your capabilities. In case of insufficient skills and time, we recommend that you seek help from professional craftsmen who will quickly and inexpensively perform the required amount of work. Residents of Moscow and the Moscow region place an order for the relevant services If you are at the stage of choosing an entrance door, then before buying, be sure to ask if it is insulated, how it will be installed in the doorway that matches the parameters of your living space, whether the installers will seal the doorway. If all these points are taken into account in advance, it is quite possible not to bring the situation to drafts. The tightness of the front door primarily depends on you.

Even the best doors can begin to creak or sag over time: no one can cancel the force of gravity and friction. And if you have heavy steel ones, then even metal will get tired of holding them. After the summer, plastic ones also “sag” - they almost always remain open in the heat, which leads to such results. There is no need to endure these "outrages", as well as spend money on their elimination. Adjusting the front doors is a delicate matter, but in most cases you can do it on your own. Once you adjust the loops and the porch with your own hands, you can then easily repeat.

Adjustment of a metal entrance door

creak;
draft - blowing from under the canvas (slits around the perimeter or top / bottom);
hard to close.

The solution to all these problems is called "adjusting the front door", but this includes very different measures - from banal lubrication and replacement of the seal, to the actual adjustments and mechanical influences.

Sometimes, to fix the problem, you need to go through all the methods, and sometimes the problem that has arisen can only be fixed radically - by replacement. Most often, this situation occurs with cheap Chinese products. Adjustment of entrance doors made in China is almost impossible. Of course, you can try to do something with your own hands: firms and craftsmen do not undertake them.

Eliminate the creak

Doors can creak for two reasons: the hinge grease is clogged or the door leaf touches the frame. Although both are called “creaking”, the nature of the sound is different. It is easier to cope with the clogging of the loops, therefore they usually start with this procedure.

Hinge lubrication

First, remove the old grease, at the same time removing the dirt adhering to it. The procedure is standard: wipe with a soft cloth wherever traces are visible. If this procedure has not been done for several years, and the loops are of the standard classical type, and even detachable, the canvas can be removed. Better to clean when removed.

If the hinges are rusty and won't come off as they should, don't try to knock them down with a hammer or sledgehammer. Do more harm than help. Better buy a rust remover. It is usually sold in the form of sprays. Apply to a rusted hinge and wait for the set time. Then remove the fabric from the hinges and clean. But this time it is necessary to remove all the rust. To bare metal, then coat with a rust converter and only then with grease.

After the old grease is removed, take the "fresh" one and apply it to the hinges. If the canvas is removed, there will be no problems - lubricate the pin and ring. If any other rubbing mechanisms are visible on the frame, lubricate them as well.

In traditional type hinges, squeaking may occur due to the fact that the washer on the stem has worn off. You inspect it after you have removed the door leaf. If it shows signs of wear, replace it. Install a new hard metal washer. Instead, you can put an engraver. He will also compensate for the load.

If the hinges are one-piece, find a can of liquid lubricant (WD40 is the most common) or machine oil that can be applied with a large syringe. Handle all moving parts carefully.

There is another method, but it is destructive. A hole is drilled in the upper part of the hinge, which is then filled with grease. The whole trick is not to damage the mechanism that is inside.

If the hinges are hidden, find all the turning parts and lubricate them. Often in such models there are holes into which oil is applied.

After applying the lubricant, swing the doors several times from side to side, distributing the lubricant. If this was the reason, the creak goes away. The final touch is to wipe off excess oil.

How to lubricate front door hinges

It is necessary to choose a lubricant, first of all, according to the temperatures at which the loop is operated. If the hinges go outside, a composition is needed that does not thicken at low temperatures. There is not much choice here:

Litol. Reliably works at temperatures from -40°C to +120°C.
Solidol. The temperature range is slightly lower, but also sufficient: from -35°C to +65°C.

For entrance doors facing the entrance and operated at positive temperatures, a few more items can be added to this list:

Eliminate friction on the box

If, after processing the hinges, the creak remains, most likely it is caused by the friction of the door leaf on the box. Inspect the door frame for wear. If you find any signs of abrasion, see which of the loops is closer. It will need to be regulated, if possible.

The difficulty lies in the fact that there are a lot of types and models of loops and it is impossible to say unambiguously what needs to be done. All that is possible is to list the main points that can be. Based on these, you may be able to determine how to "heal" your door.

Two types of hinges for an entrance metal door with adjustment

Standard hinges are not adjustable. In this case, the adjustment of the entrance doors consists in replacing the washer. They are selected with greater or lesser thickness, adjusting the position of the door leaf. Some hinges with a ball at the top have an adjustment screw. By unscrewing it, we raise the door a little, twisting it - we lower it. You can try to correct the situation with it.

If standard hinges on a steel door are welded, we can assume that this has exhausted the possibilities. If they are seated on screws, the fixing screws are loosened, moving the sash in the desired direction as far as possible. Then the screws are tightened. Check if the problem is gone. If not, try with another loop. Sometimes it is required to loosen all the loops, and pull the canvas in this position. In general, decide on the place where to press, and where to press.

There are models of hinges in which the adjustment holes are hidden under a protective cap. But it’s impossible to remove it just like that: it is fixed with a bolt, which is unscrewed from the inside of the room. An example of adjusting such a loop in the video.

If the hinges on the front door are screwed, you can eliminate the friction of the door leaf on the frame with their help. First, loosen the screws near where the wear is. Try to move the door leaf a little. To begin with, you can knock with your palm or fist, moving it in the right direction. Try opening/closing a couple of times. Did it help? Screw the clamping screws back. And try opening/closing again.

If it doesn’t help, you can use some kind of leverage, hit with a rubber mallet or hammer through the board. But don't overdo it. Especially gently should be handled with Chinese products: they are very flimsy.

If these manipulations also did not give anything, you will have to loosen the screws on all the hinges and try to move the canvas over the entire area. Take hold of the edge of the canvas with your hands and sway it. In this case, the loops should fall into place. Try to open close. If there is no squeak, tighten the bolts. That's all, adjusting the hinges of the front door cannot give more. The next thing to try is to change the geometry of the door frame. More on this in the next paragraph.

The photo above (right picture) shows a hinge with the ability to adjust. By loosening the screws, you can turn the adjusting screw. It does not help - we are trying to move the canvas, as described above.

Eliminate a loose porch (blowing from under the door)

Sometimes there is a noticeable breeze from under the front door. If you examine the perimeter, you will most likely find that in some place the fit of the door leaf to the door frame is loose. There may be a decent size gap. You can check your suspicions with a piece of paper. Open the doors, insert a piece of paper between the canvas and the jamb and close the doors. If the porch is normal, the paper is either pulled with a lot of effort, or it is pinched so that it cannot be removed. Just break. If the sheet is removed freely, then the fit is insufficient.

The simplest explanation is that the seal has lost its elasticity. If the doors are several years old, it is possible. And the first step is to change the seal. Did it help or only partially solve the problem? We move on.

Replacing the seal is the first step if it comes through from under the front door

If the canvas is displaced relative to the door in a horizontal plane, we try to eliminate the draft from under the front door first by shifting the door leaf. This is written above: loosen the fastening screws on the hinges, then try to move the canvas in the right direction. Check the result - the gap has disappeared - tighten all the screws to their original position.

Sometimes gaps under the front door occur due to the distortion of the door frame. This is checked with a level. Most likely, it skewed in the place where the sheet of paper is freely removed. The second option, on the contrary, the box is stuck out in the place where the sheet is pressed, due to the fact that the "normal" part cannot be pressed. All this is determined with the help of an eye and a level. Having determined what the problem is, we are trying to return the geometry to normal. Measures depend on how the box is installed:

See the video for the option to correct the gap in the porch. After front door installation it turned out that it was blowing strongly from under it. The owner corrected the warp with a hammer.

We eliminate the sagging of the door (shuffling on the threshold)

If, after several years of operation, the doors began to open with difficulty, while rubbing against the threshold, most likely the fact is that the ball or bearings have worn out. If possible, there are adjustments, you don’t even have to remove them. Just unscrew one of the bolts and lift it up slightly.

If there is no adjustment, there are several options:

hinge replacement;
replacement of bearings with new ones;
installation instead of bearing washers.

All this is determined based on the situation and the design of the loop.

Adjustment of plastic entrance doors

Problems can be the same: friction, creaking hinges and a loose connection to the frame, which can blow. But adjusting PVC doors is easier - hinges and mechanisms are standardized, there are not so many types. So there is hope that you can handle the problems with your own hands, without calling the master.

Balcony door adjustment

After the summer, the plastic doors to the balcony sag: in the summer they often remain open for a long time, which is why such a nuisance happens. Then they touch the threshold, an unpleasant sound is heard, the plastic is erased. In this case, you need to lift the canvas up. This is done using the adjustment, which is located at the top of the lower loop.

They do this with the lock open, but the door is closed. Take a hex wrench (usually 4 or 5) and insert it into the hole, turn it a few turns. It is not necessary to immediately lift it strongly, as this can cause other problems. Raise only until the problem is fixed.

Sometimes, when closing, the doors rub from the side, touching the metal latches. It turns out that you need to move the canvas towards the hinged part. To do this, there is another adjustment on the same loop. It is located below, visible when the door is open.

This adjustment is also carried out with a couple of turns clockwise or counterclockwise. If you need to keep the doors from rubbing against the post, turn counterclockwise. Take a couple turns and check. Once the problem is gone, stop. Otherwise, you can move so much that the lock will no longer “cling” to the counterpart.

If the upper left corner “clings”, you need to adjust the loop that is at the top. The principle is the same: one or two turns, until the trouble is eliminated.

Top hinge adjustment - top left corner pressure

Clamp adjustment (so as not to see through)

Sometimes a weak pressure is observed from the side of the castle part. It seems that the canvas adjoins exactly, but it pulls noticeably from under the door. In summer this is not a problem, but with the onset of cold weather, it significantly reduces the temperature. There are two ways. The first is to adjust the clamping pins. These are metal protrusions on the sash.

They are of two kinds. as in the photo above - oval, and round, but with an eccentric in the middle. The position of this element determines the degree of pressure of the sash against the frame. The way to change the position depends on the shape of the trunnion. If it is the same as in the photo, take the pliers, clamp and turn slightly. Maximum pressure if the long side is turned horizontally, minimum - if it is directed vertically upwards. There are also all intermediate options.

If there is an eccentric in the center of the pin, then there is also a hole for the hexagon. Insert it and turn, achieving the desired degree of pressure.

It is not recommended to set the maximum value to the stasis: the seals will quickly lose their elasticity. Also make sure that all eccentrics are rotated the same way. This guarantees the normal operation of the fittings.

But sometimes there is a situation that the sash of the balcony door is not tightly pressed from the side of the hinges. This is also eliminated by adjusting the loops. Below it is under a protective cap. Take it off (pull up). Take the key (hexagon) and adjust the pressure of the lower right corner of the plastic balcony door with a couple of turns.

There are also hidden loops on the frame, which also have the ability to adjust the pressure. They are located on the frame from the side of the hinges. Adjustment with the same hex wrench. Turns "clockwise" and "counterclockwise".

Adjustment of plastic doors

There are different hinges on the plastic entrance doors, and there is no lock-and-tilt fittings. They have closed overhead loops. They have three settings:

the height of the door leaf relative to the frame - from the bottom of the hinge;
the density of pressing the canvas to the frame - on top of the loop;
sash movement horizontally - sideways

They are enough if the doors were initially installed correctly: the limits of change in positions are significant, which makes it possible to compensate for the changes that occurred during operation.

If a creak occurs in the hinges, they must be lubricated. To do this, remove the top cap and into the opened hole, into which grease is placed. Since plastic doors are mainly used as entrance doors in private houses and they go out into the street or into an unheated vestibule, you select a lubricant that does not thicken at low temperatures (Litol and Solidol).

Apply lubricant here

In some models of hinges, the cap is simply pushed on, in others, you need to unscrew it, and then pull it out. Decide on a place.

Sometimes a situation arises when intervention is required: the lock is poorly fixed. If the sash pressure is normal, the striker needs to be corrected. She is mobile in such doors. Loosen the mounting screws, use a screwdriver to move the bar a little in the right direction and tighten the screws back. You check. Should help.

This article has collected all the data on what to do if it blows from the front door, and how to prevent the possibility of drafts when installing a new door.

If the front door is the source of drafts in your house or apartment, you are unlikely to be satisfied with such a solution to the problem, which is shown in the picture above. no less uncomfortable to curtain them with shabby blankets, creating a barrier to cold air.

Only a hermetic front door can allow you to feel comfortable at home, which will not let in not only cold air space, but also extraneous noises and smells from the street. But how to achieve this?

There are a couple of options for solving the problem:

Glue a seal around the perimeter of the canvas.
Completely insulate the canvas by sheathing it so that the insulation covers the gaps between the canvas and the box.
Completely replace the canvas.

In the event that you are only building your house, it is possible to immediately take care that this issue does not, under any circumstances, come up before you.

Eliminate drafts from an existing door

This trouble is especially relevant in suburban housing, since there the front door quite often goes directly to the street or to a cold unheated vestibule. Despite the fact that in an apartment building a draft from the door is a very unpleasant phenomenon, in addition, if the entrance is warm. Since cigarette smoke and other unpleasant odors enter the apartment with it.

Classical sealing is gluing a self-adhesive seal in the form of a rubber band around the perimeter of the box. Unfortunately, this method is not very reliable.

First of all, with active use of the door, the seal quickly becomes unusable and has to be changed.
Secondly, the slightest misalignment will cause the seal to stop fitting well to the door and not doing its job properly.

In addition, it is only possible to glue the sealant strip correctly if the door is perfectly level. If, however, a different distance is found between the frame and the leaf in different places, the rubber band will not fit well to all parts of the door.

With this placement, the sealing tape will provide better tightness of the door, in addition to its deformation and subsidence, since it will have a greater degree of freedom. Whatever the initial position of the canvas relative to the box, the sealant will work to suppress drafts precisely due to its advantageous location.

Instead of the classic self-adhesive tape, you can use for this purpose a round-section polyethylene foam sealing cord or a rubber tube made of rubber resistant to aggressive media.

And don’t let the lack of an adhesive base on them bother you: in this case, glue will help you out remarkably Moment:

Lubricate the frame around the entire perimeter with glue in the place where the sealant should be placed.
Cut the tape to the desired length, cutting the edges at a 45 degree angle to fit at the corners.
Lubricate the side of the seal with which it will be glued with glue.
At the end of the holding time, which for the Moment glue is 15 minutes, close the door and put the rubber band on the end of the box so as to ensure its tight fit to the door. Press it for a couple of seconds with your hands.

Attention! It takes days for the glue to dry completely, so try to use the door carefully on the initial day

It goes without saying that this method also has its drawbacks - the seal can be torn off by accidentally hooking it with something. But fixing the situation will not be difficult by gluing it back into place.

As mentioned above, if it blows from the front door, it is possible to completely insulate it, making sure that the insulation (see Door insulation: types and parameters) is larger than the box and covers all available slots.

For this, rollers are intentionally made, which are attached around the perimeter of the door leaf. From time to time, such rollers are attached to the door frame. You realize what the appeal is about if you look at the photo on the side.

And about how to insulate the door, you can read in more detail in other materials on the site. This may also be required if you have a dilapidated wooden door, the canvas of which has dried out and through cracks have appeared in it.

In the event that a wind blows from the front door, regardless of all the efforts made, make sure that the cold airspace does not enter through the huge keyhole. Otherwise, you need a door.

How to prevent drafts from the door

Skillful builders know that it is possible to install the front door to a house or apartment only after all the “wet” work is completed - laying partitions, plastering, puttying, whitewashing, etc. Especially if it is a wooden door, which is sensitive to high humidity.

At a time when all this work in the new house is completed, and you go to order a new door, think over your requirements for it in advance. It is clear that it must be strong and reliable, but at the time when it blows from the front door, there is little pleasant in this.

Based on this, do not forget to clarify how its sealing will be ensured. at the moment, new models of entrance doors have appeared, the boxes of which have a special configuration - a three-stage one.

An additional ledge does not allow cold air space, dust, moisture and foreign odors to enter the room. This configuration has the entire door frame, including the threshold, which is not mounted separately, but forms a single unit with the door frame.

Installing such doors will save you from having to think about how to eliminate drafts.