How to independently sheathe pipes with drywall. How to hide pipes from prying eyes with a drywall box Hiding pipes under drywall but with holes

How to close pipes with a drywall box: expert advice

When it comes to cosmetic repairs, special situations often arise. For example, the question arises of how to close the pipes with drywall with your own hands. Heating pipes, pipe risers in the corner of the bathroom, water pipes in the kitchen spoil the aesthetics with their appearance and, in general, do not have the best effect on it. It is for this reason that it makes sense to hide them. The easiest way to do this is with the help, since processing this material will not cause problems even for those who have no experience. Knowing how to close pipes, you can act in the same way for any type of pipe (for example, for gas pipes).

We invite you to learn the most elementary way to solve problems with pipes - to make a box for pipes from HA with your own hands.

To start the workflow, first you need to prepare the materials and fixtures according to the list.

To make a box you will need:

Before you start sewing pipes with drywall sheets, you should prepare the following tools:

Building level to control the evenness of surfaces.
Roulette - it will be required to take measurements, and also with its help, cutting drywall panels and a metal profile is performed.
A pencil that is needed to mark the material in order to cut it or install fasteners.
Hammer drill/drill with a drill and 6 mm bits to make holes in the wall for dowels.
A hammer.
Phillips screwdriver.
Hacksaw.
Metal scissors.
Notched grater for smoothing grout.
Spatula in order to distribute the putty solution on the surface of the HA.

Who does not know how to make a box for closing pipes from drywall, below can familiarize themselves with the step-by-step process. But first, you should clearly define and understand why exactly drywall panels are considered the ideal material for masking pipes in a bathroom, toilet or any other room. This choice is due to a number of advantages when working with this material.

These include:

Affordability.
Speed and ease of assembly design.
The neutrality of the material for human health, its safety at the ecological level.
No release of toxic substances when the sheets are heated.

When you know all the subtleties, it remains only to make the right choice in favor of the type of material. For rooms with high humidity, it is recommended to use moisture-resistant drywall, which differs from other types in green.

Carrying out work

Preparatory work

Before you start lining the riser pipes in the bathroom, you should prepare the room properly, in particular the pipes. To begin with, they should clean off the old coating and apply fresh paint. This is required in order to extend the life of the pipes by protecting the paint from the corrosion process. The fact is that after the pipes are closed by means of a box, access to them will be difficult, even if a hatch is made on the front wall of the box. When the paint on the pipes dries, this will mean that the time has come for the next stage - the creation of a frame structure for the box.

Building a support from a frame

As a rule, in the manufacture of the frame, metal profiles are used, which are made of galvanized sheet with a long shelf life and rust resistance. Sometimes the frame for the box is made of wooden beams. In order for the risers to be hidden behind drywall, the profile support is erected with a focus on the sequence of procedures.

Marks are made on the walls, ceiling and floor for the future frame, while you will need a pencil, a building level and a plumb line.
Further, according to the markup, you can begin to set up the guides, and fix them to the wall surface with dowels.
The completion of the construction of the frame consists in the installation of rack elements along the guide profile beams. The connection of profiles that are joined to each other is carried out using special fasteners, which are commonly called bugs.

So, let's move on to the most important thing.

Sheathing the frame with sheets of GK

The next step is to sew up the prepared base - a gypsum fiber blank. Here you should pay close attention to such nuances:

Use only moisture resistant panels.
Panels should be chosen with a thickness that can give the box more rigidity (i.e. 1.2 cm).
When joining drywall blanks, either edge alignment should be used (if there is a factory-type edge), or a chamfer laying method at an angle of 45 degrees.
A gap is made in the skin so that everything is ventilated naturally.
Check the position of the self-tapping screw heads - they must be sealed, and not exposed and not hanging over the wall.

So, first take measurements. After that, calculate the gap between the floor and the ceiling using a tape measure. Measure the required distance on the profiles and cut in such a way that you get 3 blanks at once. Three racks should be placed around the pipes (2 of them should be against the wall and 1 in the center between the first two), while maintaining a right angle between them. If the risers are located not in the corners, but along the wall, you will need to prepare 4 pieces from a metal profile. They will need to frame the pipes in the shape of a square, or use three racks, chamfer the corner and create a triangular support. When choosing a frame geometry in order to sew up pipes with drywall, be guided by considerations of what is best for the design.

After the gaps between the racks are measured, support-beams should be made, which are fixed with metal screws. Attention should be paid to the fact that in order to prevent deformation of the frame installation during seismic shifts, a special shock-absorbing tape should be used. It should be applied to the areas of contact of the working surface on the racks. The use of such a tape also makes it possible to level vibrations, and this will prevent them from entering the profile. Due to this, you will have protection against the destruction of the frame structure.

Sheathing with drywall sheets is performed according to one of two scenarios - either with pieces of material that was prepared according to measurements, or with a single piece of material with the removal of extra centimeters after it is fastened with self-tapping screws. If there is a shortage of a certain part, the sheets of the joints can be laid in place of the transverse rails, and after the edge of the two parts of the sheets, they should be fixed. The resulting voids between the wall and the sheathing should be filled with mounting foam.

Processing a drywall box for pipes with putty is considered the final work. But before that, the joints of drywall with each other should be glued with sickle tape. In order to give perfect evenness to the surface, the caps of the fasteners should be well puttied.

In order to get even corners, use sloping corners. A little putty mixture should be applied to its back side, and when pressed, apply to the corner. After that, using a wide spatula, it will be possible to achieve the effect of a leveled wall. When dry, the surface can be sanded and primed. After that, you can start finishing work - glue wallpaper, paint or lay tiles.

Pipe sheathing by other methods

Anyone who thinks that sheathing pipes with a drywall box is difficult or even impossible for any reason, will continue to look for solutions to the problem - how to close the pipes in the toilet with drywall. The creation of a protective wall is one of the alternatives. When creating such a wall, it must be provided with a door or a revision suite with hinged doors. The surface of the wall should be lined with materials that are used for the design of the bathroom. Often, behind such a wall, a frame for a hanging toilet bowl is masked, and the installation of the structure should be carried out according to the technical instructions that are attached to the product.

Now a little about design. Hatches and doors can be completely separate, and they can be finished with tiles. For their better opening, you should use special fastener loops, which are also called frogs. You can also make shutter doors or install roller shutters.

As you can see, drywall finds a beneficial use in such matters as the installation of all kinds of structures that hide engineering networks from prying eyes. It is only important not to forget that in this case you should buy a special type of material (moisture resistant) and be sure to follow the instructions.

There are pipes in every room, and especially a lot of them in the bathroom, toilet and kitchen. And often they only spoil the appearance of the room, and do not decorate it. Therefore, the question “how can pipes be closed” is more than relevant today.
Pipes can be sewn up using a wide variety of materials.

Today, there are many options to mask communications indoors. The most widespread of them:

with built-in furniture. This is the simplest and best option;
create a drywall construction. Such a box will make it possible to qualitatively and beautifully sheathe communications, including a gas pipe in the country house;
chipboard box. Here it will be possible to create a lightweight design that will suit any interior;
decoration. In this situation, sheathing can be carried out with a variety of materials - twine, wallpaper, paint, artificial stones, etc.

Note! The choice of plating method should be done taking into account your financial capabilities, as well as being guided by your own preferences.
With so many options, you can disguise the hated pipe, even gas, in the most suitable way for you. But most often, a drywall box is chosen as a disguise, since it can be easily made with your own hands.

Making calculations

The creation of a drywall box for masking pipes requires calculations and the creation of a scheme, according to which the structure will be installed in the future.
We make the drawing as follows:

box drawing

we put on paper communications that we mask;
the distance between the pipes and the frame is at least 3 cm;
we draw the elements of the metal frame indicating the locations of the jumpers.

Note! In the drawing, you need to lay down the dimensions of the frame and the thickness of the drywall sheets.
The drawing will help you accurately calculate the amount of materials needed for work.

Preparing for installation

Preparation for work on the creation of a drywall box or false wall involves the following steps:

clearing the place of future work;
wall primer. If you need to close the gas pipe, prime with an anti-mold and fungus agent;
on the walls we apply markings corresponding to the drawing.

Now you are all set to install the structure.

Tools required for the job

A drywall box can only be made with the following tools:

Tools for the job

perforator and drill with drills;
tape measure and pencil;
building level;
spatula.

Now you can definitely start the disguise itself.

Main stage of work

For many people, the question "how to close the pipes with drywall" is quite complicated. But if you follow our instructions, this issue will stop worrying you.
Installation of such a design always begins with the creation of a metal profile:

to the markings that are applied to the floor or walls, we attach the profile guides;

Note! Instead of metal profiles, wooden slats can also be used, but they should be pre-treated with special tools.

we drill holes in them with a puncher and fasten them to the dowels;
with a high box, at intervals of 50-60 cm, we install rack profiles. They will play the role of jumpers. Jumpers are required if the distance between the racks is more than 25 cm.

box frame

In a situation where the elements to be sheathed are in the corner, we begin to install the frame from the corners. All stages of mounting the frame should be carried out using the building level.

Sheathed pipes

If there is a need, then at the end of the installation of the metal structure we fix soundproofing materials. It is best if you carry out these actions simultaneously with plasterboard wall cladding.
Upon completion of the installation of the frame, it can begin to be sheathed with drywall. sheathing happens like this:

cut the sheets into pieces of the desired size. It is best that these are long stripes, especially if the box is high. For cutting we use a knife on drywall;
We fasten the sheets to self-tapping screws.

At the end of the installation, you should get an impeccably smooth design.

Shutdown

At the end of the work, you should give your design an aesthetic and beautiful appearance. To do this, you will need to do the following:

process all the joints of the sheets with sickle and putty;
it is also necessary to putty the places where the screws are screwed;
after that, we prime the entire box;
the final step will be the application of finishing putty. Its layer should be very thin.

Then we give the structure its final look by painting, wallpapering, etc. That's it, your communication disguise is ready!

Socket boxes and the secrets of their installation in drywall Drywall planers, options, pros and cons

Finishing

Depending on the location of the riser pipes in the bathroom, such a box can be:

solid partition;
a separate closet in the corner;
protruding from the wall.

The first option is relevant when all communications in the toilet are located behind the toilet near the rear load-bearing wall. It is very simple to make it, since it only requires the installation of a frame from a profile and the fastening of one continuous sheet of drywall. But in this case, more material may be required, and this method takes up a lot of space from an already small toilet room.

If the sewerage and water supply pipes are located in the corner of the toilet, a neat corner box is made. The guide profiles go from the floor to the ceiling, stiffening ribs are attached between them, the entire frame is sheathed with drywall and then proceed to its decorative finish. The box will be in the shape of the letter G.

The issue of access to pipes and water meters during the construction of such partitions is very relevant. The box can be made removable, then, if necessary, the entire structure is removed entirely. The advantages of this method are that at any time convenient access to the entire riser from floor to ceiling can be made, but this design will be very cumbersome, and it is quite difficult to remove the box from metal profiles and drywall. Therefore, usually removable boxes in the bathroom are made of plastic, PVC and other lighter materials.

A much more common method of accessing a riser in a box is by installing a door. In the frame, a rectangular frame is made from the profile - it will serve as a hole to easily get inside.

Doors can be made from the same drywall, plastic, PVC, plywood or other available materials. They can be single-leaf and double-leaf, removable or hinged. For convenient closing, they can be made with locks, a latch, on magnets. Competently mounted doors, matching the finish with the box and walls of the toilet, look very nice.

There are a lot of options for decorative finishing of riser boxes for pipes. The most common option is to veneer them with PVC panels. They look great, are protected from moisture, are very easy to install. With this method, if the box is angular or U-shaped, you need to purchase decorative plastic corners in order to make the design look more aesthetically pleasing.

When decorating a drywall pipe box, it can be equipped with additional functions. There are designs with shelves for toiletries, niches for a brush or plunger, hooks for towels and other useful details. You can use the partitions of the box as efficiently as possible, you just have to show your design imagination.

In addition to decorative facing options for masking pipes, there is also an “internal” one - installing wiring in the toilet in specially punched strobes. With the help of a wall chaser, a puncher or a door, special grooves are cut out in the places where pipes are laid, where water and sewer branches are hidden.

The sewer riser has a large diameter (100-110 mm), so it is not sewn into the walls, but the cold water and hot water pipes easily fit into the strobes

Preference for hidden installation is given to straight sections of the pipeline with one-piece or conditionally detachable connections and nodes. The "invisible" installation has two main advantages: the absence of plumbing parts, the appearance of which does not match the beautiful wall cladding, and space savings.

There are a number of rules prescribed in regulatory documents that sharply limit the use of gating:

it is impossible to lay strobes in load-bearing walls;
for flush mounting, only pipes connected using a one-piece, monolithic technology (soldered) are suitable, access to other types is required;
the gating zone should be free from electrical networks;
when choosing the width of the strobe, it is necessary to take into account the linear expansion of the material (for example, polypropylene expands in all directions);
clamps are used for installation so that the pipes do not make sounds when in contact with the walls; sometimes a heat-insulating material is used.

When the box is ready, we overwrite all its sides with a grater with sandpaper.

Cleaned corners on a drywall box

The box is ready, we proceed to its lining;

prepare the putty mixture, as written on the package;
with a spatula we hammer all the seams;
glue sickle on fresh plaster, to prevent the appearance of cracks;
re-apply plaster;
as soon as the seams dry, you can apply the primer. It is advisable to make two layers, while each should dry before applying the next;
as soon as the last layer of primer dries, after about 3-4 hours, you can start finishing.

If it is supposed to be painted, then you will have to putty on three layers, then clean it to perfect condition.

When using wallpaper, two layers of putty are enough, then the box is covered with a primer and after that it is possible to paste over.

It is worth noting that if you wish, you can assemble a box with built-in shelves in the bathroom and toilet, but this will require a little more skill.

Repair in the toilet does not look complete if communications and plumbing are left open. There are several ways to give a neat look to the wall near which the pipes are located, any of which can be easily implemented in a room of any size, which means that they are suitable for even the most compact toilets or combined bathrooms.

We offer you the following options:

The first way to design the area where the pipes are located is to install blinds. With their help, you can hide the unflattering appearance of the pipes, they do not need to be fastened for a long time, moreover, the blinds are easy to clean. The disadvantage of this design is that the blinds are not very reliable, they can break and then you need to replace them completely.
The second option for decorating pipes is a communication cabinet. It can be made according to the principle of a conventional cabinet built into the wall, assembled from improvised materials or sized and mounted in a custom niche. The advantage of the cabinet is access to all pipes and valves. In addition, in such a cabinet, you can additionally put shelves for household chemicals or textiles. Unfortunately, cabinets of this kind do not fit into all interiors, and in a small bathroom, along with shelves, they will also take up a lot of space.
The best option for any design solution is a drywall box in which pipes and a ventilation shaft will be closed. It is easy to make, can be finished in many ways, and the shape of the box can be given, based on the characteristics of the room.

The communications in the bathrooms look unattractive, therefore, in most cases, when starting an apartment renovation, the owners of the living space want to build a drywall box for pipes. Someone invites a craftsman for this, but if you have at least a minimal idea of \u200b\u200ba building tool, you can close the pipes yourself.

The choice of material and the necessary tools

The construction of the box is not a complicated process, but in this work there are some nuances that you should know for a positive result. For installation, you need to buy materials, and:

fasteners - connection elements, "seeds", dowel-nails;
plaster;
silicone-based sealant - useful for sealing joints with the floor;
revision hatch;
drywall
profile - and .

Material for creating drywall construction

To work, you will need tools, there are not so many of them, so it will not be difficult to prepare it:

spatula;
screwdriver;
perforator;
drill 6 mm;
metal scissors;
screwdriver;
level;
roulette;
knife and hacksaw;
bath;
container for mixing the mixture.

Drywall Tools

Once everything is ready, you can assemble a drywall box, consider step-by-step instructions.

Step-by-step instructions for making a pipe box

Before you start assembling a drywall box, you need to draw up a project. Do not ignore this stage, as it is one of the most important, since the quality of the box made on its own depends on it.

Step-by-step instructions for assembling a drywall box to hide sewers will be described using the example of a bathroom and toilet, the installation process for hiding pipes in the kitchen is identical to that described.

You do not need to create an exact drawing, just make a schematic drawing with the dimensions of the future structure transferred to it.

Diagram of a drywall box for pipes

Watch the video: how to close the pipes with a drywall box.

Further, it should be noted on the floor and ceiling, the location of the guide profile, for this you need a building corner. Substitute the corner with a short edge to the corner at the intersection of the floor and wall, and draw a straight line on the floor. The angle between the strip on the wall and the strip on the floor should be 90 degrees;

The same should be done on the ceiling.

The markup is ready, you can proceed to the next step.

Mounting and installation of a frame from profiles

Before the construction of the metal frame, you need to cut the required number of profile segments equal to the marked lines.

See in the video: assembling the frame for the future GKL box.

How is the installation done:

You need to start by installing guide profiles on the floor and ceiling, and then on the walls. They are installed strictly along the lines, and fixed with dowel-nails. To do this, press the profile strongly against the floor and drill holes in the floor directly through it at a distance of 15 cm from each other. Insert dowels into the holes and screw in the screws;

After that, you can proceed to the installation of rack profiles. It is inserted along the guides from above and below. The profile is pressed and fixed with dowel-nails. The ends of the flexible connection are bent inward, or cut off. The main requirement in this situation is that the profile must be level;
The next step will be the installation of the corner connecting profile, it is screwed with small self-tapping screws to the intersection of the guides at the corner of the future box;

Fastening the rack profile to the guide using self-tapping screws

Then the stiffening frame is mounted in the pipe box - the profile at the wall and the profile at the corner are connected in small segments. The segments are located strictly parallel to the floor at a distance of 30 cm from each other, along the entire height of the frame on both sides.

Important! The entire assembly must be level controlled, even a small deviation, which can lead to a poor-quality assembly of the structure. This manual will help you assemble and install a box that can cover the heating pipes.

Firstly, under this design, reinforcement is made from profiles, in size.

Secondly, such hatches are quite heavy, so you need to fix it carefully, not sparing self-tapping screws.

Also at this stage, it is necessary to determine where the ventilation grill will be installed, it is necessary so that condensation does not form inside the box.

Many apartment owners, upon completion of the installation of pipes or heating systems in the house, are wondering how to close them with an outer box and what kind of sheathing to use for this. Everyone has their own preferences in this matter, however, the material that is most often used for this purpose is drywall.

Advantages of drywall boxes

In general, the construction of the outer box can serve various purposes, for example:

Give designs an aesthetic appearance.
Provide protection against accidental mechanical and other damage.
Achieve a soundproofing effect (especially in the case of sewer pipes).

Gypsum boards meet all these requirements well, and although other materials can be used to build the box, they are preferable for a number of reasons:

Low price.
Ease of assembly design.
Excellent environmental performance.
High sound absorption rates.

It is not difficult to work with this material, and therefore the involvement of professionals is optional, and with some skills, you can close the pipes with drywall with your own hands.

Preparation for sheathing pipes with plasterboard boxes

Before sheathing the pipes with drywall, some preliminary work should be done, which are as follows:

Preparation of the necessary materials, including metal profiles (rails, rack), screws, dowels and drywall sheets themselves.
Preparation of the necessary tools (knife, screwdriver, hacksaw, plumb line, level, pencil).
In the case of metal pipe products, it is advisable to clean their surfaces of old paint and repaint before sewing up the pipes with drywall. After sheathing the pipes with drywall, access to them becomes very difficult or impossible.

Upon completion of these works, before you close the pipes in the room or in the bathroom with drywall, you must first prepare a reliable frame for its fastening.

Do-it-yourself frame installation

The material for the construction of the frame structure, to which the plasterboard sheathing will be attached, is usually metal profiles (rack and guides) made of galvanized sheet.

These products are resistant to the process of corrosion and rust, and therefore their use ensures a long service life and the absence of serious problems during operation.

Work on the manufacture of a frame structure consists of the following steps:

Marking lines and contours of the frame on the floor, walls and ceilings, carried out with a simple pencil using a level and plumb line.
Installation of guide profiles in accordance with the marks and their fastening to the wall with dowels.
Installing three vertical rack profiles and measuring the distance between them.
Inserting rack profiles into the rails and fastening them to each other with small special screws called “bugs”.

After these works are completed, the frame for the planned sheathing can be considered ready, and it is possible to proceed with the construction of the box itself from drywall sheets.

Plasterboard box installation

Sheets of drywall are prepared for the assembly of the skin, after which they are cut into fragments of the desired size.
The blanks are inserted between the profiles and placed for subsequent fixation.
Plasterboard blanks are fastened to the frame using self-tapping screws. The screw heads should not penetrate the drywall by more than 1 mm. Screwing plasterboard sheets with screws to the frame is done on both sides.
The ends and edges of the used sheets protruding beyond the structure are sawn off with a hacksaw. Edges in places of cuts are leveled by means of a diamond grid No. 100.

Processing and finishing plasterboard sheathing

If we are talking about how to sew up heating pipes with drywall, or you need to surround the heating system as a whole with a box, then it becomes important to have holes in the casing for heat to escape into the room. It is desirable that such heat holes have a diameter of five centimeters or more, but they can be replaced by a large number of holes of small size.

During the summer, the heat vents are not used, and in order to prevent dust and other particles from clogging them, it is recommended that they be closed until the next winter. A handy option are commercially available hinged lids that can be left open in cold weather and closed in the spring/summer season.

If it is necessary to box ordinary household pipes in the kitchen or in the toilet, or the question is how to sew up the pipes in the bathroom with drywall, then the presence of such holes is not required.

In addition, lining and additional arrangement of a drywall box provides for several types of work:

Sealing of attachment points, slots and seams. As a rule, ordinary polyurethane foam is used for this purpose.
Strengthening the outer and inner corners of the box with steel corner profiles, which not only helps to align the corners, but also provides additional protection against accidental mechanical damage.
Inserting the exhaust flange into the top of the mounted duct.
Puttying work followed by grinding with a grout mesh or sandpaper.
Decorative finishing of the erected cladding structure. There are plenty of options here to choose from. For example, wallpaper can be pasted over the box, painted in the desired color with paint or emulsion, covering the lining with self-adhesive furniture tape, using liquid wallpaper, decorative plaster, etc. Which option or style to choose depends on the imagination, taste and preferences of the owners of the home .

As you can see, lining pipes with drywall does not present any particular difficulties, and does not require high professionalism or sophisticated equipment. This is due to the popularity of drywall boxes for enclosing pipe and other structures. Their manufacture is within the power of any self-taught home master who will carefully read the instructions and observe accuracy and thoroughness in work.

How to sheathe pipes with drywall: how to close, do-it-yourself sheathing with a plasterboard box of pipes in a room, how to sew up in a bathroom

How to close pipes with drywall: instructions

This article will talk about how to close the pipes with drywall, how the individual stages of installing a drywall box are performed, and detailed instructions for installing such a box.

After completing the outdoor installation of pipes and batteries, people often have a question about how to close the pipes with drywall. Other building materials can be used for this, but drywall sheets are the most convenient and are used most often.

About drywall boxes

Drywall box

The choice in favor of sheathing pipes with drywall is due to a number of advantages of this method, for example:

Ease of construction;
Affordable material price;
Environmental safety of the material and the absence of the release of harmful substances when heated.

Before sheathing pipes with drywall, the following materials and tools should be prepared:

Profile metal rack and guide;
Drywall sheet;
Screws.

When figuring out how to sew up pipes with drywall, the first step is to prepare the steel pipes for heating and radiators themselves by cleaning pipes and radiators from old paint, and re-painting with paint for heating pipes.

This will prevent the appearance of rust and premature damage to the pipes, since after the box is made, the pipes will no longer be accessible and painting will become impossible.

After the paint has dried, proceed to the installation of the frame for the drywall box.

Frame manufacturing

The frame of the pipe box in the bathroom or other room is made of guide and rack metal profiles, for the manufacture of which a special galvanized sheet is used, which ensures sufficient durability of the profiles and resistance to rust.

Making a frame for a drywall box includes the following steps:

The contours of the frame are marked on the walls, ceiling (in the case of lifting the pipe up) and the floor with a level, pencil and plumb line.
A guide profile is installed along the drawn line.
The profile is attached to the wall with dowels.

Important: to prevent damage to the structure during seismic activity, you can lay a special shock-absorbing tape in all places where the profile and the working surface come into contact.

The tape is designed to absorb vibrations without transferring them to the frame, preventing damage to the structure during seismic activity.

After fixing the guide profiles, they are inserted into the elements of the racks.
The fastening of two profiles to each other is carried out with the help of bedbugs - small special screws for metal.

How to close pipes with drywall

After installing the metal frame, the pipes are directly sheathed with drywall.

Important: you can significantly simplify and speed up the process of how to sheathe pipes with drywall by preparing drywall blanks for the box in advance.

To fasten drywall blanks to the frame, screws are used, screwed into the blank in such a way that their heads do not sink deeper into the drywall surface than 1 mm.

Important: if the screw heads are sunk too deep, the fastening of the workpiece may turn out to be of poor quality as a result of a rupture of the cardboard layer of the sheet.

Thermal holes

In the case when the box is made in order to hide thermal radiators, it is necessary to make thermal holes in it.

They allow thermal energy to freely enter the room through the walls of the drywall box in winter. To make holes, an electric drill with a crown (special nozzle) is used.

The holes can be any diameter you like, but it is recommended that the diameter be at least five centimeters. In the case when large diameter holes spoil the interior of the room, you can make a large number of small diameter holes that follow the contour of the box.

Useful: special swivel covers are available for thermal openings, which can be opened in winter and closed in summer.

Finished box processing

Box on the ceiling

After completing the sheathing of the frame with drywall sheets, it remains only to process the box, which includes the following steps:

First close up all attachment points and seams;
Strengthen internal and external corners with a metal corner profile, which allows you to protect the structure from accidental mechanical damage, as well as make the corners perfectly even;
Prime and putty the finished structure;
After the putty has dried, the surface is polished with sandpaper or a grout;
Next, you can perform a decorative finish on the structure, for example, wallpapering or painting in the desired color.

Step-by-step instruction

Consider step by step how to sheathe pipes with drywall with your own hands:

The first step is to perform measurements and other preparatory work described above.

Measurements of the required distances

Three rack-mount vertical profiles are installed.

Vertical rack profiles

Measure the distance between profiles.

Measuring the distance between installed profiles

The resulting distance is measured on another profile.

Measuring the distance on the profile

Cut out several blanks.

Blanks are inserted between the profiles.

Fasten the workpieces with self-tapping screws or a cutter.

Drywall sheets are screwed with screws to the profiles on both sides of the frame.

Saw off the protruding edges of drywall sheets with a hacksaw.

With the help of a diamond mesh No. 100, the edges of drywall are leveled.

The gaps between the drywall and the wall are filled with mounting foam.

Insert a flange under the hood into the resulting box.

This completes the installation of the drywall box. With the help of this instruction, the process of closing pipes with drywall is quite simple and fast. A video on hiding pipes with drywall will help to solve the questions that have arisen regarding the installation of the box.

How to close pipes with drywall: how to properly sheathe with your own hands, video instructions for sheathing

275) How to close pipes with drywall: how to sheathe them with your own hands, video instructions for sheathing.

Sheathing pipes in the toilet with drywall with your own hands

The piping of the apartment in the vast majority of cases is located in the toilet. Its main elements are cold and hot water supply risers, as well as sewage. Usually all three of these lines are behind the toilet or in the corner of the room. They do not look very aesthetically pleasing, therefore, during the repair work, they usually try to close them. The question of how to sew up the pipes in the toilet with drywall so that the room acquires an attractive appearance is relevant for many home craftsmen.

Where do we start?

Before you close the pipes in the toilet with drywall, you should audit the communication systems, otherwise problems may arise later, the solution of which can result in great trouble.

Check all pipes for damage and severe defects.
How tight are all pipe connections? If there are leaks, be sure to fix these problems.
Remove old coatings from pipes, rid them of traces of rust, repaint with a fresh coat of paint, if necessary, "dress" them in cases of insulating material.
Make a plan drawing of your pipeline, put on it all the connections and locking devices. This scheme will help out a lot in case of emergency.
Think about where in the drywall construction the inspection hatches will be located, providing access to the pipes during their operation and in case of emergencies.
If you have old metal pipes installed, it may be more rational to replace them with modern polypropylene products. Such pipes are just as strong, but they look more aesthetically pleasing, weigh less and are affordable.

How can you hide pipes with drywall?

We propose to analyze the two most popular options for how to close the pipes in the toilet using GKL.

Method number 1. False wall

They resort to it if the pipes of the drain and sewer are located behind the toilet on the entire wall. The proposed design is easy to implement, its execution scheme looks something like this:

Installation of guide profiles UW or is carried out along the perimeter of the area to be closed (on the ceiling, on the walls, on the floor). They are fixed with ordinary dowel-nails.
Racks made of CW profile are installed vertically. Do not forget about the need to leave a small space for the viewing window.
We mount the crossbars from the CW profile. As a result, a cellular crate is formed.

Based on the size of the sections of the frame, drywall sheets are cut, standard self-tapping screws for metal for drywall are used to fix them.

The toilet room is often only 0.75–0.8 m wide, so just one sheet of drywall can be enough to make a false wall for masking pipes., The standard dimensions of which are 2.5 × 1.2 m.

If the structure will be tiled, there is no need to level the wall with putty. It will be enough just to process the drywall with a primer.

Now you can proceed to the final finish (tile, painting, etc.).

Method number 2 Drywall pipe box

It is used if the communications to be masked are located in the corner of the toilet. Such sewing is considered more difficult, since it is necessary to build a frame of an angular structure, and then sheathe it with drywall.

Determine exactly what the dimensions of the box being built will be. Keep in mind that it should be compact, but extremely functional, hide not only pipes, but also shut-off valves for both risers, and an inspection window will be located on it to audit the condition of the sewer system.

Apply markings to the ceiling, it will determine the contours and dimensions of the future box. The distance between the walls of the drywall box and the pipes is about 10–15 cm.
Using a plumb line and a hydraulic level, transfer the contours to the floor.

On the wall surface, draw lines along which the connections of walls and corners will pass.
After finishing the markup, proceed to assemble the frame. For its construction, it is necessary to install guide profiles on the floor, ceiling and walls according to the markings made. For fastening, dowel-nails are used.
Now we connect the opposite corners on the ceiling and floor with a vertical profile. It is he who will serve as the basis for the box that closes the pipes. For structural rigidity, this vertical profile should be connected to the guides installed on the walls. For this purpose, pieces of the ceiling profile cut to the required size are used. Crossbars are installed every 40 cm.

In this design, to mask the pipes, it is also necessary to leave room for a viewing window, place it opposite the shut-off valves.

You can clarify for yourself the moments that remain incomprehensible by watching a video that tells how to sew up pipes in a toilet with drywall.

How to secure access: 3 most convenient ways

To ensure easy and quick access, it is most convenient to use one of the options below:

Roller shutters or blinds. An excellent solution when creating a false wall at the rear wall of the toilet. Attached to the frame, provide the widest access to the pipeline. In this case, the finishing area is reduced, it is not necessary to think over the ways of fastening for the hatch. In addition, behind them you can organize shelves for storing household chemicals.

Sanitary hatch. You can make it yourself, but it's easier to buy it in a store. Can be metal or plastic, used alone or under tiles.
Removable magnetic tiles. An interesting solution that can be used when decorating a toilet with large tiles. A hole is made according to the size of the element, magnets are inserted between the drywall and the tile on its surface, 4 metal plates are glued on the sides of the removable tile.

As you can see, the process of high-quality masking of water pipes and a sewer riser with drywall is not so complicated. With due care, attention and a little skill, it is quite possible to carry it out on your own, significantly saving your own money.

How to close the pipes in the toilet with drywall with your own hands (video)

How to close the pipes in the toilet with drywall with your own hands: video. We make a box and a false wall. Preparation, installation of structures, providing access to pipes.

How to close pipes with drywall

Major repairs in dwellings often involve replacing pipes. Upon completion of the installation of pipes or radiators, it becomes necessary to hide communications to create a favorable appearance of the walls in the bathroom, toilet or in any other room. A lot of work done during the renovation period with expensive tiles, underfloor heating and attractive plumbing fixtures, and a lot of effort put into creating a pleasant interior, can be in vain if you do not think about masking communications.

Various materials are used for such work, but the most acceptable is the use of drywall, from which the box is made. Why the choice falls on drywall?

The advantages of a drywall box for pipe sheathing are due to the following:

affordability of drywall;
ease of manufacture of plasterboard structures.
environmental safety of drywall, characterized by the absence of harmful substances in its composition. This is especially true in the manufacture of boxes for batteries and heating pipes that emit heat during space heating.

Some information about drywall. This popular building material is characterized by a multilayer structure with alternating gypsum and paper layers. Drywall sheets are on sale in the size of 2.5 by 1.2 meters. One sheet of drywall will be enough to make a box for a fan riser.

wood or metal

First of all, you need to assemble the frame. For the manufacture of the box, both a metal profile and a wooden bar can be used. The advantages of a metal profile made of galvanized steel is that, unlike a wooden beam, it has increased resistance to moisture and is not exposed to rust for a long time.

The advantages of a wooden frame include the environmental friendliness of wood and a higher degree of sound insulation.

Materials and tools

Before proceeding with the manufacture of the box, you should consider a set of tools and materials.

Materials and tools:

sheet drywall;
metal profile (guide and rack);
dowel-nails, self-tapping screws for fastening parts of the box;
special knife for cutting drywall.

You will need materials such as mounting foam, cushioning tape, putty to level the surface of the box. Of the tools, a drill, a hammer, a screwdriver, a tape measure, a level, a plumb line, a pencil will come in handy.

Preliminary work

The preparatory work includes the processing of steel heating pipes and radiators (heating radiators), from which the old paint is removed and, if necessary, a new one is applied. Paint as an insulating material will protect metal pipes from premature rust damage. These works must be completed before installing the box, which will subsequently block access to the pipes.

The above work will not be required if the manufactured box is used for sheathing plastic water pipes.

Frame assembly and cladding

A drywall box is fixed to a power metal frame with vertical and horizontal profile elements.

The finished frame is sheathed with sheets and strips of drywall, pre-cut to fit the dimensions of the frame. Drywall parts are fixed to the profiles with self-tapping screws. They are screwed into the drywall with a slight recess so that they can be hidden under a layer of plaster.

There are several ways to close the pipes with drywall:

1. Carry out the "preservation" of the pipeline of the fan riser: remove rust from pipes, replace damaged pipeline sections, prime or paint pipes, repair joints between pipe sections.

2. Start work on installing the cladding box should be from the bottom. This means that marking the dimensions of the box, taking into account its contours, should be applied by drawing straight lines using a corner, starting directly from the floor surface - to the left and right of the pipe. Sections of profiles of the required length are fixed horizontally with dowels along the lines drawn on the floor. Similarly, horizontal profiles are installed on the ceiling (or elsewhere on top of the future box). Vertical profiles are attached to the installed horizontal ones. Next, the remaining horizontal profile elements are added in increments of 60 cm.

3. Cutting blanks from drywall is carried out after the final installation of the frame from the profiles. Drywall is cut with a special knife, often used for cutting wallpaper. On the front side of the drywall sheet, lines are drawn for the external dimensions of the individual sides of the box from the profiles. Furrows are applied along these lines with a knife - alternately for each workpiece. The notched drywall blank is simply broken and then cut from the back of the drywall sheet.

4. Arrangement of a window (vent) in a drywall box opposite the fitting (faucets and connecting devices on pipelines). The need for such a window is obvious - during operation, regular revision and repair of the sewer system is necessary.

Only after you learn how to close the pipes with drywall, and do all the work on installing the box, you can start finishing work. They may include applying plaster to the surface of the box and then painting it, or lining the box with ceramic tiles.

How to hide pipes from prying eyes with a drywall box

During the renovation, much attention is paid to the decoration of the premises. But the efforts will be in vain if you ignore the pipes in the bathroom or radiators. These communications must be hidden from prying eyes so as not to violate the integrity and design of the interior. To do this, you can close the communications with a specially made box. This design does not take up much space.

When choosing a material for its manufacture, pay attention to practicality. Although wood and thin metal sheets are used for such purposes, drywall is most often used. How to make a drywall box with your own hands will be described below.

Drywall as a material for the box

If you are in doubt about whether drywall can be sewn up with drywall, consider its advantages:

Ease of installation. Not a professional can make a box for drywall, with detailed instructions and the necessary tools.
Non-toxic material that does not emit harmful substances even when heated. And this is important, given the proximity of pipes or radiators.
Relatively low cost of materials.

In order to make a drywall box, you need to stock up on tools and materials:

Actually drywall. The sheet measures 1.2 wide and 2.5 or 3 meters long. It is enough to cover the pipe.

Note! In order to sheathe pipes in places with high humidity, in the bathroom and toilet, you need to take moisture-resistant drywall. He is green.

Use a galvanized metal profile that does not corrode due to high humidity. It is better not to use wood for the frame.

Self-tapping screws, fleas.
Drywall knife. They also cut wallpaper.
Screwdriver.
Level and plumb.

A hammer, drill, tape measure, pencil for marking borders, putty and spatula, polyurethane foam will come in handy.

The thickness of the drywall sheet is different, but to close the pipes in the bathroom with drywall, choose 12 millimeters.

Let's take a closer look at where to start and how to close the pipes with drywall. When everything you need is at hand and you can get to work, carefully inspect the pipes. If they are new and installed during the repair, then there should be no problems. Also, all the actions described below do not apply to plastic pipes.

If it is decided to sew up old metal pipes, then check them for rust. If it appears, clean and prime the affected area. Before you finish the pipe with drywall, you need to paint it. This will prevent further rusting and prolong the service life. This important point cannot be missed, since in the future access to the pipe will be closed or limited.

How to make a frame

When making a box from a drywall profile, the first priority is marking for the future frame. Make marks on the ceiling (in the case of lifting the pipe up), and then use a plumb line to outline the contours on the floor. You need to make markings on the walls, using the level. It is important to maintain a distance from the partition to the pipe of at least 5 centimeters. If we are talking about heating pipes, then the distance can be made even larger so that the material does not overheat and the appearance of the decorative finish does not deteriorate.

Now start making the frame. For this:

Attach the UD profile to the floor and ceiling, following the line drawn in pencil.
Install rack profiles (CD) at the corners of the box and against the wall. Additionally, check their verticality using a plumb line or level.
Fasten the cross bars between the posts. The distance between them should not exceed 60 centimeters. This will strengthen the design.

The profiles are attached to each other with fleas - small metal screws.
Now you can sew up the pipes with drywall. Self-tapping screws are used for this, but make sure that their caps do not sink into drywall by more than 1 millimeter.

When erecting drywall structures with your own hands, remember how to properly cut drywall. A line is marked on the sheet, after which it is cut with a knife at 2/3 of the sheet depth. Putting the sheet with the back side on the edge of the table, break it sharply. The smooth edge is ready, it remains to cut off a thin layer of cardboard on one side.

The work will go faster if you cut a sheet of drywall in advance. This can be done with a special knife.

Even if the decision is made to remove the pipes in drywall, access to them may be needed at any time. For such cases, a door is provided opposite the taps and fittings.

Thermal holes: their importance and decorative finishes

Question: is it possible to close the heating pipes with drywall,

haunts those who want to do it, but are afraid

due to ignorance of all the subtleties of the process. There are several reasons for such fears:

Will heat flow from the radiator into the room if the battery is sewn up with drywall?
Will drywall get hot?

These problems are easily solved by making thermal holes. They are made with an electric drill with a special nozzle. The diameter of the holes can be any, but the best option is from five centimeters. You can do less, then you need to increase the number of holes.

Important! There are decorative covers that perform two functions: they give the structure completeness and a beautiful appearance, and at the same time they have a lattice that allows air to circulate freely.

How to process the finished box?

When the manufacture of the drywall box is completed, you need to process it. First, the seams and fastenings are processed. Then the surface of the box is primed and puttied. To get perfectly even corners, you need a metal corner. To fix it, putty is applied inside, the corner is pressed against the box and pulled along the corner. After that, it is necessary to putty everything, achieving a flat surface at the place where the corner is attached. After drying, the wall is sanded and primed. The next step is decorative trim.

What exactly it will be depends on the premises and on the desire of the owners. If the heating pipes were sewn up with drywall, which is more often related to living rooms, then you can paste over the structure with wallpaper or paint it. If you had to seal the plumbing pipes with drywall in the bathroom or toilet, then tiles are a more appropriate option. Do not worry: the device of the drywall box is reliable and strong, it can easily withstand the weight of the tile.

If the noise in the pipes bothers you, then this design also solves this issue. Between the pipes and the wall of the box, you can lay a soundproof material, such as mineral wool.

Step-by-step instruction

Measurements, marking and other preparations.

Installation of rack vertical profiles.

Measure the distance between them.

Cutting blanks from the profile, taking into account the measurements obtained.

Attaching workpieces using self-tapping screws or a cutter.

Screwing drywall to profiles.

Aligning the cut edge with a diamond mesh.

Blowing out the cracks between the wall, floor and drywall with mounting foam. This is necessary so that moisture does not get inside.
Insert flange under the hood.

The next stage is the decorative finishing of the drywall box. You should not highlight the box with a different color, since in this case all the attention in the room will be focused on it. And the task is just the opposite - to hide the pipes without attracting attention. This is how you can easily and quickly make drywall constructions with your own hands, without resorting to the services of a master. This is done quickly - a few hours, and the box is completely ready.

How to make drywall constructions with your own hands: instructions

Find out how to quickly and inexpensively sew up toilet and bathroom pipes with drywall sheets. Detailed step by step instructions for work. What tools are needed