Diagonal laying of laminate: material calculation and installation features. Laminate diagonally: a new way to emphasize the originality of the interior (27 photos) Is diagonal laying right for you

With a certain level of training, skillful hands and the availability of the necessary set of tools laying laminate in a diagonal way is possible. Be patient, calculate the required amount of material, prepare a set of special tools - and get to work.

Laminate - diagonal or straight?

To make the flooring look elegant and become a real decoration of your apartment, find out which option is more suitable for you: straight or diagonal.

Features of the direct method

This type of installation is suitable for a room of any configuration, if the walls are fairly even, and there are no distortions of the building box. Important feature: if there is a lot of furniture in the room, or there are carpets on the floor, choose only the direct installation method, otherwise all the charm of the diagonal coating will be lost behind the ledges and corners. In this case, we cannot talk about any graceful lines.

With the direct method, you need to start laying the coating from the door so that the laminate pattern runs parallel to the light flux. Professionals note that the light that illuminates the floor from the window does not give a shadow at the seams, so the illusion of a perfect coating is created. The floor seems very even and smooth.

Important: to achieve this effect, the windows should be located only on one side of the room. If you install the floor across the lines of the incident light, then the proportions of the room will be distorted (the room will “stretch out”). Please note when buying that trimming the material will take at least 7% of its total amount.

Diagonal way

If the room is spacious, with a minimum set of furniture, you can choose this particular installation method. This coating option will be able to hide the wrong or broken wall geometry.. The diagonal coating will look aesthetically pleasing and spectacular.

The styling technique is much more difficult than with the direct method. Masters who have some experience in arranging the floor using laminate can cope with the work.

note: the stock of material must be at least 15% so that it is enough for trimming. Remember that the methods for calculating the required number of boards are different for the straight and diagonal methods.

Instruments

You will need:

Roulette for measurements;
Electric jigsaw;
Metal ruler;
Wooden block to tamp the panels;
Pencil;
Special hammer for laying with a rubber base;
Spacer wedges (for fixing gaps along the walls).

How to lay laminate flooring diagonally?

How to lay laminate diagonally? If one of the walls in your apartment is located at an angle or a semicircle to the others, it is worth starting work from it. The angle at which the boards will be located, everyone chooses for himself. Most often it ranges from 30 to 45 degrees. If the angle is larger, then the number of trimmings will increase much.

Important start work in such a way that the light from the windows passes along the long part of the board. Then the floor will seem monolithic, and the area of \u200b\u200bthe room will visually expand.

Laminate calculation

For direct method it is enough to find out the area of \u200b\u200bthe entire room, divide by the area of \u200b\u200bone unit (one board) and round the result. Everything, the number of boards is calculated. It remains to add 7% for cuttings - and the calculation is over.

How to calculate the laminate when laying diagonally? Diagonal variant has a formula that differs from the previous version. To the product of the length of the room and its width, you need to add the product of the width of one board by 1.42 times the width of the room.

The mathematical form is:

AC is the width of the room;
CD is its length;
1.42 is the square root of 2.
(ACxCD) + (1.42 AC x the width of one board).

for example, room size: 5 by 7 meters. The width of one board is 10 cm (0.1 m), and its length is 100 cm (1 m).

Algorithm for finding the required number of pieces of laminate panels.

S rooms: 5х7=35 sq.m;
S spare amount of material: (1.42 x5 x 0.1) = 0.71 sq.m;
S boards (1 piece): 0.1x1 = 0.1 sq.m.

Substitute the values in the formula:

35+0.71=35.71 sq. m is the total amount of material.
35.71/ 0.1= 357 pieces.

It is this number of boards that is needed with a diagonal version for a room 5m wide and 7m long.

Ways

Stages of work with a diagonal laying option.

Need to prepare the floor, make a screed, let it dry well, check how smooth the floor turned out. Gypsum fiber boards or sheets of dense plywood can also serve as the basis for laminate flooring.
Necessarily pull the cord or rope diagonally, which will control the laying angle and show the slightest deviations from it;
Next, the substrate is laid out on the floor. The sheets are joined end-to-end and glued with a special adhesive tape of sufficient width;
The angle of inclination of the panels is selected. To make it clearer, you can lay out several boards on the floor;
To make it easier, experts recommend starting work from the center of the room and going to the corners. It is easier to start with long boards than with small triangles;
After assembling several rows, you need to connect them together. Careful measurement is very important;
A rubber mallet will help to fit adjacent boards tightly and securely. Do not overdo it so as not to damage the lock;
Prepared wedges need to fix the gaps between the board and the wall. If you have not prepared the wedges, you can use scraps from a laminated board. But this is unprofessional. Prepare a special set in advance;
If heating pipes pass at the masonry site, you should immediately cut holes for them. They are easy to seal with acrylic-based sealant or silicone of a suitable color;
It remains to put the plinth. It is worth choosing high-quality products, inside of which there are channels for pulling a cable with edges made of rubber. This ensures a tight fit to the floor. Buy corners and connectors that are easy to attach to the wall using dowels.

A few practical tips for laying laminate flooring.

Calculate the required amount of material, taking into account marriage and waste;
Choose expensive and high-quality material. Savings can lead to the fact that during the service life coating defects may be detected, which appear due to the poor quality of a cheap coating;
After purchase, let the boxes with laminated panels rest for at least two days. The temperature in the room should be +17 degrees and above, so that the level of humidity and temperature during storage and in the place of permanent use gradually equalize;
Work on the arrangement of the floor using laminated panels only in dry rooms. A high level of humidity or its sudden changes are unacceptable (boards can swell and warp);
Keep water out of the laminate, especially in the case of buying a budget option for panels, where the quality of the material is lower;
Do not forget about the substrate and a level base to avoid differences in floor height;
When laying laminated panels, leave "thermal seams" which are protection that prevents the boards from buckling during compression and expansion due to exposure to moisture. Gaps should be on all sides of the room between the coating and the wall;
The size of the gap is simply calculated: each meter of existing floor width requires 1.5 mm clearance around the perimeter. In the office, the size of the gaps should be significantly larger, since the area of \u200b\u200bsuch premises and the differences in humidity and temperature are much greater there.

Advice: if the room will have heavy, bulky furniture that will interfere with the natural processes of expansion and contraction of wood panels, you need to leave gaps within 10 mm on each side of such a room.

In these photos you can see what the room looks like after laying the laminate diagonally.

Laying laminate in a diagonal way is really difficult. But the result will justify your expectations. The time and effort spent on this responsible work will fully pay off with the aesthetic, elegant appearance of your apartment, the floor of which will be beyond praise.

Having chosen laminate flooring for their living space, most home craftsmen decide to do all the laying work themselves. Well, great! However, there is one big “but” in this: an unprofessional approach does not take into account the individuality of each specific room. We offer you to understand the nuances.

In the instructions for the packaging of the laminate, the easiest installation method is indicated, which consists in placing the boards parallel to the walls. And it is precisely this method (it is written in the instructions!) that the vast majority of "home-made" ones follow. Of course, if the room in which the laminate is laid is of a strictly geometric shape (deviations of several degrees are not taken into account), then this method is preferable.

But if the walls are uneven, decorated in a semicircle, or are there simply flaws in the layout? In this case, another way of installing the laminate may be more successful - laying diagonally.

With the usual laying method, laminate boards are arranged parallel to the surface of the walls, and with a diagonal one, at an inclination of 30-45 °. Observance of a slope of 45 ° is considered optimal, but since adjacent walls are rarely strictly perpendicular, the angle within the same room may vary within the above indicated limits.

Advantages of laying in this way

Knowing how to lay laminate diagonally will come in handy not only when you need to hide layout flaws or smooth out uneven walls. Diagonal flooring is often used by interior designers when they want to expand the space of a narrow and dark room.

This approach will pay off especially strongly if the room is not cluttered with unnecessary furniture. Then the diagonal lines visually stretch the floor and, accordingly, it seems that the room has become freer.

Well, the last argument in favor of this installation method is that the diagonal floor pattern looks more interesting than the usual parallel installation. It opens up a real field for creativity and allows you to modify the room, stretching it, making it brighter, highlighting separate functional areas.

If you have a glazed and well-insulated loggia and you choose a floor covering for it, then you can use a laminate. In the next article we will talk about how to do it right:.

Calculation of the required amount of laminate

Diagonal installation is more complex than traditional parallel installation and requires more consumables. Therefore, when calculating the amount of laminate, it is necessary to plan for future waste of 15-20% of the material.

For professional builders who have extensive experience in laying laminate flooring, this percentage is not as high and approaches a minimum of 5%. But, since you are just learning, we recommend that you add 15-20% to the area of \u200b\u200bthe room and use this figure as the total amount of laminate.

An example calculation can be done here:

Technology and stages of diagonal laying

Between the walls and the laminate flooring, it is necessary to leave small gaps 1.5-2 cm thick. These seams compensate for the swelling and shrinkage of the floor covering during temperature or humidity fluctuations.

To maintain the same distance around the entire perimeter of the room, you can use special pegs, which, after installation, are removed from the resulting seams. Then the gaps are closed with skirting boards fixed on the walls.

A problem for home builders-enthusiasts can be caused by the process of trimming the outermost lamellas in a row. You need to cut the edge of the board at an angle, and so as to completely repeat the outlines of the wall. To do this, measure the distance from the top point of the row to the spacer peg and, accordingly, from the bottom point to the peg.

The resulting distances are transferred to the whole laminate board in the form of two points - above and below. These points are connected by a line, along which the panel is subsequently cut. Cut the laminate from the back with a jigsaw or a regular hacksaw.

Thus, there is nothing supernatural in laying a laminate diagonally. A little more accuracy, preliminary calculations, planning and the amount of consumables are required. But as a result, you will get not only a beautiful and durable floor, but also the opportunity to visually expand such valuable square meters. And it's worth it, isn't it?

Laying laminate diagonally not only diversifies the design of the room, but also visually expands the space. Such installation is a little more difficult to produce compared to a simple ordinary installation, but taking into account the recommendations of specialists, everything can be done with high quality and with your own hands. Some problems in work are compensated by the peculiar and attractive appearance of the flooring.

Styling features

Laminate flooring has gained wide popularity as a floor covering, which is facilitated by its many advantages. Almost all instructions for its installation are guided by standard installation, when the panels lie strictly parallel to the walls. This method is fully justified when the room has a strictly rectangular shape, and the walls converge clearly at a right angle.

What to do in the case when the shape is far from ideal, and the walls are not parallel, and even there are rounded corners and other atypical shapes? Standard, ordinary laying of laminate will only emphasize all the flaws, making them more noticeable. Diagonal laying of panels will help to solve the problem. With this system, the panels are laid at an angle of 30-45 degrees to the wall surface. The best option is 45 degrees, but depending on the curvature of the wall, the angle can vary within the specified limits.

What are the advantages of diagonal styling?

In addition to smoothing out construction defects, this arrangement of the laminate visually expands the space, and the effect is most pronounced in an uncluttered room. Designers successfully use this effect. In addition, the diagonal arrangement looks more original, and makes it possible to design the interior in an unusual style. At the same time, different colors of panels manifest themselves differently in visual perception.

Before installation, it is necessary to ensure the adaptation of the laminate to the conditions of the room, for which it must stay in it for at least 2 days before starting work.
It is desirable to carry out work at a temperature of 18-22 degrees and humidity in the room within 40-65 percent.
The preparation of the floor surface is important. Irregularities should not exceed 2.5-3 mm per 1 m.
Laying the laminate is done on the substrate.
The consumption of material in a properly carried out diagonal laying is not much higher than the material requirement in a conventional installation. Cut off pieces can be used at the beginning or end of other rows. It is generally accepted that when forming diagonals, the planned flow should be increased by 7-9 percent. If a certain pattern is also laid out, then the consumption should be increased by 14-15%.
The maximum size of the room where diagonal laying can be done is 7.5-8 m one way (width or length).
It is not recommended to lay laminate on a floor with an electric heating system.

A compensation gap of at least 10 mm must be left around the entire perimeter of the room at the place where the laminate adheres to the wall, which is then closed with a plinth. This condition eliminates the effects of shrinkage and temperature changes.

Preparatory activities

The preparatory stage begins with cleaning the floor from debris and dust, as well as carefully leveling the surface. Roughness is checked using a long straight rail. If you apply it to the surface and lean towards the floor, then the irregularities will reveal gaps that can be measured with a ruler. When they exceed the allowable limits (3 mm), leveling is carried out with a cement mortar.

The next important preparatory step is the laying of the substrate. It is made of rolled or tiled material. The most commonly used options are polypropylene, cork, coniferous mats or sheets of extruded polystyrene. It should be noted that the use of a foam polymer underlay eliminates the need for thorough preparation of the floor surface, since able to smooth out the imperfections.

The next important preparatory step is the laying of the substrate.

To carry out the work, you should prepare the necessary tools in advance - a jigsaw, a knife, scissors, a mallet, a hammer, a tape measure, a square, a building level, a brush for applying glue.

Wooden wedges will help ensure the same gap. In addition, you will need a wooden block for knocking out laminate tiles.

Technological features of laying

To ensure the correct diagonal laying of the laminate, the following rules must be observed:

Based on design decisions, the direction of laying the panels is selected. Their installation is recommended to start from the corner farthest from the door, on the left side.
A laying angle of about 45 degrees is selected. If there are special deviations of the room from a rectangular shape, then the angle can be reduced.
Along the entire perimeter of the floor, along the walls, stakes are installed to form the same gap 1 cm wide.
Using an electric jigsaw, the corner of the panel is joined so that its desired slope is formed after laying.
.Neighboring rows of laminate are laid with a checkerboard pattern, i.e. the joint between the elements of one row should fall on the body of the adjacent element (at a distance of 1/3 of the panel length).
Panels are fastened depending on the type of lock. The most common option is Click-lock. In this case, to connect the side edges to each other, the panel is raised at an angle of approximately 45 degrees, and a spike of the adjacent panel is inserted into the groove. The elements are lowered to the floor, and then, using a wooden beam, they are carefully knocked out with a mallet. The strips must be strictly parallel, and the gap should not exceed 1.5-2 mm.

When carrying out work, it is worth considering specific nuances. It is easier to ensure diagonal laying if the panels are at least 30 cm long. If there is a radiator in the room, then the row should be started under it, because the final lining under it is very inconvenient to do. If adhesive is used, it must be allowed to dry completely before checking the strength of the installation.

For ease of installation and constant control of the line, it is recommended to stretch beacon cords, which will be a visible guide to maintain the desired angle over the entire floor area.

Diagonal laying of laminate is sometimes simply necessary in the presence of large defects in the construction of walls. It can be done in such a way that the coating will not only hide errors, but also create an unusual interior. You can carry out the work with your own hands, and with their proper organization, it will be possible to avoid unnecessary waste of material.

Laminate is considered a versatile wood flooring that has a well-groomed appearance, and installation is simple and accessible to everyone. However, one should not be treated negligently, because with insufficient accuracy and chaotic following of the step-by-step guide, the connection of the lamellae may be loose, which means that dirt and dust will enter large gaps.

In addition, any laminate is treated with a water-repellent sealant. Accordingly, large gaps require more putty, which looks extremely untidy.

Laying the laminate diagonally looks interesting, this process requires even more perseverance and, of course, an accurate calculation of the required material.

Cons and pros

Benefits of diagonal laminate flooring

The classic and common version of the arrangement of lamellas for wooden flooring consists in placing joints in parallel with respect to the main source of daylight - a window opening.

Of course, each has its pros and cons. What are the benefits of diagonal laminate?

Laying laminate diagonally is better when the window is slightly to the left or right, and not in the center of the wall. Thus, the principle of parallel lighting will fully comply with the diagonal placement of the lamellas.
It is appropriate to use the diagonal version of laying the laminate if the walls of the room have noticeable defects.
Designers use the diagonal placement of the laminate, because it creates a visual effect of expanding the room, thereby increasing the square footage of a cramped living space.

Main disadvantages

There are also disadvantages of diagonal laminate. The most basic - with diagonal laying, the consumption of laminate is greater, so the material must be purchased in a larger volume than usual. Major expenses are due to the fact that at the points where the ends of the panels are attached to wall structures, they must be cut at an appropriate angle and adjusted each time in different values. There are a lot of surpluses and scraps that remain after cutting and mounting the lamellas, but, unfortunately, they are completely useless, they cannot be used.

Experienced professionals have learned to determine the right amount of wood cover in such a way that only 5% of all purchased material is leftovers. If you are a beginner and for the first time you are faced with the need to lay a laminate diagonally, it is worth laying a large number of lamellas in the reserve. Finishers recommend focusing on a percentage of 7% or, in extreme cases, a margin of 0.1 of the entire perimeter of the room.

Take into account the higher consumption of laminate

So, for convenience, we propose to apply a formula that will help to make an accurate calculation: C * 1.1, where C is the area of \u200b\u200bthe floor structure that is planned to be processed with a laminate. If after that we divide the obtained value by the perimeter of the lamellas packed in one package, you will get the number of sets, the contents of which are enough to cover the room with wooden material.

Once you have decided on the required quantity, go shopping to the store and purchase the entire set of panels at one time. Beginners often make an unforgivable mistake - they collect only a part of the lamellas with the hope of buying the rest of the goods later, but then they face the problem of the lack of an identical type of wood, painted in the required shade, especially when it comes to a rare manufacturer.

Preparatory stage for laying laminate flooring

How to prepare the floor surface

To lay the laminate diagonally, you must have a leveled floor in the room. The laminate fits perfectly on the concrete surface, simplifies the process of a complex of construction works related to the waterproofing device and. Such preparation requires not only a bare foundation, but also an old layer of finishing material on the floor. The floor must be brought to an ideal state - it must be washed as even and stable as possible.

Any creaking sounds, subsidence and floor care in depth are a harbinger of the fact that the laminate will leave the best, and here the situation does not depend on the quality of the material and its manufacturer.

What should be linoleum? No delaminations, bubbles, swelling and scuffs, through holes and holes should not be visible to the naked eye. Pay attention to whether the concrete screed is collapsing, if it has lost its integrity, you will have to build a new foundation.

So, if you decide to lay the laminate diagonally on top of the concrete, prepare a primer solution (how to do this is written on the label of the material). It is desirable that the composition indicate the parameter of deep penetration of the mass. After the solution is applied in an even layer, it is necessary to leave it to dry completely. After that, the floor structure is covered with a polyethylene film.
It is preferable to mount the laminate with your own hands on a substrate, which can be made of either cork or polyurethane foam. The substrate panels are fixed to each other and connected with adhesive tape.
The best option is to lay the room with OSB panels, which provide a flat plane and additional noise and thermal protection effect.

Planning installation work

When the laminate is already at home, open the package and leave it to rest for a couple of days. During this time, the slats perfectly adapt to the room temperature and humidity, which means that you don’t have to worry about the subsequent slats after their installation.

Be sure to think over the installation work, given the scale and size of the purchased raw materials. The scheme will facilitate and systematize the sequence of laying work, as well as help to avoid mistakes when cutting the material.

Experts recommend adhering to the angle of inclination of the panels at 45 degrees, but if desired, this value can be changed up to 30–40 degrees. Be aware that slopes less than 30 degrees cause an ugly cut and generally complicate the process of fixing the laminate.

Step-by-step instructions for diagonal installation of laminate

Method "From the corner"

Take one solid panel and cut along two edges, focusing on the desired angle. The first piece cut out will be a help for the entire wood flooring. To compensate for the thermal swelling of the raw material, wedge the surface, starting from the wall structures, by a value of 10.

If a heating pipe passes near the corner where the installation begins, it is correct to lay the laminate from here, immediately cutting off two lamellas at the seam for the hole going to the pipe.

Gradually move from the corner of the room to the middle. A small open corner is closed separately; small scraps of raw materials can be used. Accordingly, each next row will be lengthened. To make the rows look beautiful, provide for an offset of the transverse joints by ½ of the lamella size (along the length).

Panels of any row are connected at the ends, not including the segments falling to the wall planes. Lay one row, but do not fix it too tightly to the other. Take a measurement at two points passing from the two edges of the last even lamella to the wall itself. This dimensional step, minus the 10 mm laid down by the technology, falls on the lamella, which should be cut - mark the line and mark it with a jigsaw or hacksaw. The same should be done with the other edge of the row.

Method "From the center"

Some experts prefer to start laying the slats diagonally from the center of the room. The longest prefabricated row is taken as the basis, located at the intersection of straight lines emerging from opposite corners of the room. Laying is done in the same way as described above.

This method of laying a wooden canvas is especially convenient when the room is equipped with outwardly facing corners - it can be a ledge, a column, it is possible to transfer the surface from one room to another.

It is better to lay out the first row closer to the outer corner, if this is not possible, you need to make the necessary measurements regarding four or more points. When laying a laminate, the lamellas of which are not connected to each other with the help of a locking device, but are fixed on the glue, after the first three rows it is necessary to take a break from work and take a break of at least 3-4 hours.

If you have purchased wood flooring that says "Click" on the packaging, the "From Center" pattern does not apply. The fact is that this system of arranging the locking mechanism provides for inserting the comb into the groove at an appropriate angle, after which the lock snaps into place. Thus, the installation consists in laying all the parts in one direction, and nothing else.

When the diagonal installation is completed, remove the spacer bars and fix them, but in no case to the skirting board floor.

Conclusion

Now you know what diagonal laminate laying consists of. When installing, be extremely careful - beginners often do not track the location of the spike and groove connection, cutting the corner cut out on the other edge. The proverb “Measure seven times, cut once” will come in handy here.

Laminate flooring, carried out in accordance with all the rules, is always a spectacular result in the form of a beautiful floor. It will not be difficult to make such a laying on your own if you adhere to proven technology. Laying the laminate diagonally requires the same. A little more diligence, patience, time and an unusual approach to a typical floor covering will transform the room, hide its architectural flaws.

Advantages of diagonal styling

In addition to an unusual design solution, the diagonal laying out of the laminate allows you to hide the uneven arrangement of the walls. If they are in relation to each other not at an angle of 90 °, then with such a floor it will be imperceptible. In addition, the diagonal laying of the laminate allows you to visually expand the space of the room. These advantages are relevant for a small room.

Typically, the floor is laid perpendicular to the wall with a window, in which case the light will slide across the floor without highlighting the joints between the boards. Laminate diagonally in the interior of the room, where the windows are on different walls or shifted to a corner, can be the best design move regarding lighting.

The disadvantages of diagonal masonry are the additional costs of the material, and, consequently, the high price of the issue.

Calculation of the amount of laminate

Laying laminate diagonally requires more consumables. The fact is that the panels will have to be cut from the ends at an angle, which leads to an increase in waste. If the flooring is installed independently for the first time, then it is better to play it safe and purchase material 10-15% more than the norm. Although professionals make a margin of 5%.

Before laying the laminate diagonally, the number of panels is calculated using the following formula: the floor area is multiplied by 1.1, i.e. the amount of laminate will increase by 10%. If the resulting number is divided by the area of one laminated board, then you can get the exact number of panels needed to repair the floor.

Experts advise buying the necessary material in full.

How to lay the laminate diagonally with your own hands - step by step instructions

Since the store may then not have the desired color, and shades from different manufacturers are different. Even shades from the same company, but in different batches, may not be suitable.

Preliminary work

We prepare the floor

Before laying the laminate diagonally, and in general in any way, you should check the floor for stability and evenness of the surface. Floorboards should not sag under the weight of a person, should not creak.
You can lay laminate on a concrete floor, on linoleum, wooden floor, parquet, etc. before that, you need to lay it with a special substrate.
If the old coating sags or creaks, then these shortcomings should be eliminated by carrying out the necessary repair work. It may be necessary to open the floors and align the logs.
Linoleum, which was decided to be left under the new laminated coating, should also be without obvious flaws in the form of swellings, delaminations, holes. Otherwise, the panels will not lie flat or will sag and deform over time.
Before laying the laminate on concrete, the concrete surface is coated with a waterproofing agent. After that, a plastic film is laid on it.
Under the laminated coating, the substrate must be covered. It can be polyurethane foam or natural cork. Regardless of its naturalness, the sheets of the substrate are laid butt-to-joint and fastened with adhesive tape.
OSB boards make it possible to perfectly level the floor surface and additionally isolate the room from noise and save heat in the room.

Preparing tools and materials

After purchase, the panels should be unpacked and left to "lie down" for 2-3 days. Thus, the material will take the optimal parameters (temperature, humidity, plasticity), which will exclude its deformation after installation.

To lay the laminate diagonally with your own hands, you will need some tools:

fine-toothed hacksaw or electric jigsaw;
a hammer with a nozzle made of wood or rubber;
special curved mount for mounting near-wall elements;
measuring instruments: tape measure, ruler, square with an angle of 45 °;
pencil or water marker.

In addition, wedges 1 cm thick will be required, which will not allow laying the laminate tightly against the wall. Instead of wedges, you can use trim panels, inserting them between the board and the wall.

Choose an angle

Laying the laminate diagonally with an angle of 45 ° is considered optimal. At the same time, less material waste remains, because. trimmings will be well suited for use in other masonry areas.

A smaller laying angle obliquely up to 30° is possible. With a lower indicator, the coating will not look aesthetically pleasing, giving the impression of an imbalance in the interior.

Floor installation

The layout of the panels starts from the far corner of the room or from its middle - these are the main ways of laying the laminate diagonally. The strength of the floor is increased by laying the panels in a checkerboard pattern or like a brick wall. Before laying the floor diagonally, you should draw a work plan, given the scale. This will avoid blunders, and the laminate floor will turn out perfect.

The laying of the laminate diagonally is clearly shown in the photo and video.

From the corner

Further laying depends on how the first panel is laid correctly:

The first to put should be a whole panel, trimmed on both sides at the right angle. At the same time, the corner of the floor itself remains open, it is laid at the end of installation, filling it with suitable trimmings. Laying the floor should be from the far corner in relation to the door.
Further, the panels are joined to each other, and the gap between the masonry and the wall is strictly observed throughout the work.
The new row is installed in its place, but is not finally fixed, the panels are docked only at the ends.
The end panels are the last to join the row, after they are cut to the required length, taking into account the centimeter gap.
When all the details of the row are ready, they are removed from the lock, finally joined from the ends and the entire row is engaged with the previous row. This stage is more convenient to carry out with an assistant.

If all corners of the room are perfectly correct, i.e. have a value of 90 °, then the trimmings will be great for subsequent rows. At the same time, material consumption is noticeably reduced, and, consequently, the cost of repairs is reduced.

From the center

Before laying the laminate diagonally, starting from the middle of the room, a long row is assembled according to the method described above. Those. first, whole panels are assembled in a row, then the extreme elements are cut at the desired angle. The entire row is joined at the ends and laid in the center of the room. The next row is also assembled and interlocked with the first.

The further scheme of laying the laminate diagonally is carried out alternately, first in one direction to the corner, and then in the other direction.

This method is especially appropriate if there are external corners (ledge, column, transition from one room to another). When laying adhesive laminate, take a three-hour break after the first three strips to allow the adhesive to set. If the laminate has CLICK locks, then the "from the center" method is not possible due to the characteristics of the adhesion.

At the end of the installation of the floor, install the plinth. They are attached to the wall, but not to the floor.

Dear visitor! You are in the archive of the old mastergrad.com forum

How far away from the wall should laminate flooring be?

Diezel Aug 6 2004 09:20:50	Please tell me how to lay the laminate correctly, in the sense of what distance from the wall to the laminate is considered correct? As I understand it, the laminate should "breathe", i.e. will expand / contract and it is necessary that the wall is not an obstacle to it. The search didn't help. And in general, how much does it shrink in winter or expand in summer? Laminate on locks 22-23 class.
Joker (Taganrog, Russia) Aug 6 2004 10:13:53	It should be in the instructions. If not, here are the instructions for KronoFlooring laminate: http://plastik.nm.ru/montag/laminat_m.htm And another article on the topic of laying laminate: http://www.stroycity.ru/product/parket_ukl_bezkley.html
Diezel Aug 6 2004 10:42:23	Joker, the link to Stroycity is broken - there are no articles ... 🙁
Diezel Aug 6 2004 13:57:18	As I understand it from the first article - there should be wedges between the wall and the laminate - it turns out 15 mm. Is everything right? Do the wedges prevent the laminate from subsequently "breathing"?
Anton (moscow, russia) Aug 6 2004 14:08:25	And subsequently wedges should not be. You need to take them out.
Diezel Aug 6 2004 14:09:58	After assembly, then take it out, on top of the plinth? Is 15mm up to the wall okay? Are skirting boards attached to the wall in this case?
Diezel Aug 6 2004 14:11:25	And another question: during assembly, should the wedges be on the side of the laminate board and on the end? Or just on the side?
demand Aug 6 2004 16:36:53	in my opinion 1.5mm per meter of room width
Anton (moscow, russia) Aug 6 2004 17:41:54	The gap is calculated according to the instructions for the laminate per unit of length and width (different along and across). In a room of normal size - no need to fool your head: 15mm around the entire perimeter is enough. If the walls are perfectly even, then just along the wall you can put laminate trimmings in 2 layers (8 + 8 = 16mm). Since the walls are always curved, stepped wedges are used to adjust the gap. Laying laminate diagonally with your own hands - VIDEO They are needed from the sides where you will push the board, collecting it into the castle. Otherwise, just the entire plane of the floor will leave. After laying the 20 sq.m. room and removing the wedges, I easily moved the entire floor to even out the gaps. Naturally, the skirting boards are then attached to the wall.
Serg (Samara, Russia) Aug 7 2004 01:05:53	2Diesel: > Are skirting boards attached to the wall in this case? Skirting boards are always attached to the wall. Best regards, Sergei
Diezel Aug 9 2004 08:39:34	Thanks everyone for the replies!
Joker (Taganrog, Russia) Aug 10 2004 10:19:35	The link is normal (it is in the favorites), it looks like it was just nailed :(( When attaching the baseboard, do not pinch the laminate too much, otherwise your gaps will not help it.

Features of the laying process

smoothing uneven walls;

also laying can be done from the center.
Laying laminate diagonally: technology and nuances of diagonal installation

To do this, a cord is pulled through the center diagonally between opposite corners of the room. Laying is carried out parallel to the cord with a gradual removal from it to the sides.

Features of the laying process

The biggest difficulty for novice workers is the stage of cutting laminated panels, which must be placed against the wall. The bottom line is to cut at an angle, while completely repeating the outline of the wall. The pegs help in this, by which the near and far points on the panel are determined, connected by a line and cut from the inside with an electric jigsaw.

Outcome

The basics of laying laminate at an angle
The advantage of diagonal laying
Calculation of the amount of laminate for laying
Beginning diagonal laminate flooring
Features of the laying process

Laminate is gaining more and more popularity as a floor covering, which many owners not only buy for the interior of rooms in their homes, but also strive to install it on their own without involving specialists from construction companies. The article will discuss how the diagonal laying of the laminate with your own hands is carried out no worse than that of professionals and what are the features of this process.

The basics of laying laminate at an angle

A common thing for many owners of their own homes is to buy a laminate and lay it exactly according to the instructions on the package, but there is no elegance and zest in such a coating. No construction company will present photos of such flooring as an advertisement for their own services, since they do not attract potential customers.

It is reasonable to use this method only in cases where certain conditions of the room require laying boards butt-to-butt and not otherwise.

If the room has some design flaws, or vice versa, the designer’s idea (rounded walls or characteristic projections of the floors), then the option will look aesthetically pleasing when the laminate is laid at an angle to the walls.

Traditional flooring installation involves laying planks parallel to one of the pairs of walls. Diagonal laying implies observance of an angle from 30 to 45 degrees. The angle is selected depending on what angle is observed at the junction of two walls. See also: "Which laminate layout is best suited for a room."

The advantage of diagonal laying

Usually do-it-yourself diagonal laminate flooring is done because it is original. But, nevertheless, laying a laminate diagonally has its pros and cons and it is necessary to take them into account before purchasing materials and starting work.

We are talking about the following advantages of technology:

hiding various layout flaws;
smoothing uneven walls;
visual expansion of space in very narrow rooms with a lack of natural light;
naturally, the diagonal arrangement of laminated panels is much more beautiful.

Actually, you can experiment with a similar laying method if there is enough time and money for this. For example, designers, taking into account the latest fashion trends, like to zoning rooms, combining a variety of colors and textures, or joining different floor coverings. See also: "How to lay a laminate along or across - the choice of laying method."

Calculation of the amount of laminate for laying

Before laying the laminate diagonally, it is necessary to correctly calculate the amount of material in order to carry out installation without additional purchases and overpayments. Diagonal laying implies increased costs, because the laminate is purchased not to spare, but 15-20 percent more (for waste). If earlier the owner had experience in laying such a coating, then you can make a stock of only 5-10 percent.

Beginning diagonal laminate flooring

Naturally, laying laminate at an angle, like any other coating, can only be done after careful preparation of the subfloor: leveling and cleaning from dust, dirt, debris, liquid, etc.

You can start the installation process:

from the far corner of the room, located opposite the front door. This is done so that the joints of the planks (on the long sides) are located along the sunlight entering the room through the windows. Thus, joints can be made less noticeable, which makes the coating more aesthetic in the photo and visually increases the space;

Features of the laying process

First, a row of panels is assembled into one solid long structure by snapping the lock fasteners. Then he joins the already laid row. Before laying the laminate diagonally, you should find an assistant who will help at least at the initial stage, since the longest rows will pass through the center and it is quite difficult to combine such rows with each other.

Without an assistant, the procedure is performed using a small weight. First, several panels are snapped into place, and a load is placed in some place so that when working on the remaining part, the previous section does not disperse. See also: "How to lay a laminate - do-it-yourself laying sequence."

Laying, as in the case of the usual parallel version, must be carried out with some divergence of the ends of the boards. Each row should be shifted by about 30-40 centimeters, as is the case with the installation of a ship deck. This condition is required to increase the strength of the coating.

In addition to laying the laminate diagonally correctly, some features of this coating should be taken into account. We are talking about a possible change in the size of the flooring due to fluctuations in temperature and humidity in the room. Each specialist will say that it is necessary to create an expansion gap between the laid laminate flooring and the walls.

The width of such a gap should be from 1.5 to 2 centimeters, and then the coating will definitely not be deformed due to an increase in temperature or air humidity. In order to maintain the distance from the laminated panels around the perimeter of the room to the walls, you should use special pegs or small bars that you can make yourself. Upon completion of the work, they are taken out. The gaps themselves will be covered with decorative plinths.

Of course, the diagonally laid laminate has disadvantages, but they are commonplace: the high complexity of the work being done and the high cost of materials (taking into account the fact that you need to buy more). The increased consumption of laminate when laying diagonally can be eliminated if you seek the help of a laying specialist, then the overrun of the material can be reduced to 3-5 percent.

Laying laminate diagonally with your own hands (photo)

The pegs help in this, by which the near and far points on the panel are determined, connected by a line and cut from the inside with an electric jigsaw.

The points are determined by measuring two distances:

from the top corner of the row to the inserted peg;
from the bottom corner of the row to the inserted peg.

Then, points are set at the same distances from one and the other part of the bar.

Outcome

The article describes in detail how to lay a laminate diagonally, what are the main advantages and difficulties of this process. If the owner wants to get a high-quality and organic looking coating in his own home, then this method is the best fit. See also: "How to lay a laminate - a sequence of actions."

Do not forget that any difficulties will be overcome by professionals from a construction company who can take responsibility not only for laying, but also for choosing a floor covering, taking into account the basic wishes of the owner.

The basics of laying laminate at an angle
The advantage of diagonal laying
Calculation of the amount of laminate for laying
Beginning diagonal laminate flooring
Features of the laying process

The basics of laying laminate at an angle

It is reasonable to use this method only in cases where certain conditions of the room require laying boards butt-to-butt and not otherwise.

The advantage of diagonal laying

We are talking about the following advantages of technology:

hiding various layout flaws;
smoothing uneven walls;
visual expansion of space in very narrow rooms with a lack of natural light;
naturally, the diagonal arrangement of laminated panels is much more beautiful.

Calculation of the amount of laminate for laying

Beginning diagonal laminate flooring

Naturally, laying laminate at an angle, like any other coating, can only be done after careful preparation of the subfloor: leveling and cleaning from dust, dirt, debris, liquid, etc.

You can start the installation process:

from the far corner of the room, located opposite the front door. This is done so that the joints of the planks (on the long sides) are located along the sunlight entering the room through the windows. Thus, joints can be made less noticeable, which makes the coating more aesthetic in the photo and visually increases the space;
also laying can be done from the center. To do this, a cord is pulled through the center diagonally between opposite corners of the room. Laying is carried out parallel to the cord with a gradual removal from it to the sides.

Features of the laying process

The biggest difficulty for novice workers is the stage of cutting laminated panels, which must be placed against the wall.

Laying laminate diagonally: photo, video, diagram

The bottom line is to cut at an angle, while completely repeating the outline of the wall. The pegs help in this, by which the near and far points on the panel are determined, connected by a line and cut from the inside with an electric jigsaw.

The points are determined by measuring two distances:

from the top corner of the row to the inserted peg;
from the bottom corner of the row to the inserted peg.

Then, points are set at the same distances from one and the other part of the bar.

Outcome

Calculation of laminate when laying diagonally

Tool and preliminary operations

Diagonal laminate flooring

Video of laying laminate diagonally

Photo of laying laminate diagonally

Calculation of laminate when laying diagonally

Many mistakenly believe that the consumption of laminate when laying diagonally is uneconomical, has a lot of waste and will require advance purchase of material with a huge supply. Having correctly approached the task, it is enough just to purchase a laminate in an amount that exceeds the area of \u200b\u200bthe room by 5-15%.

Tool and preliminary operations

For such styling, the same tools are used as with the classical one: a hacksaw, a tape measure, a bar, a ruler, a hammer, a pencil. Preliminary operations consist in trimming the solid base, cleaning it from dust, laying the substrate and placing expansion wedges.

Diagonal laminate flooring

It should be understood that laying diagonally does not require an exact angle of 45 degrees, it can be from 30 to 45. To hide the joints, the panels must be positioned so that the long seams coincide with the direction of the sun's rays falling on the coating.

The required clearance from the wall is 10 mm. Laying laminate diagonally can be started in two ways. The first involves laying the very first panel in the corner of the room, and then move from the window towards the door. In the second method, the thread is stretched between two corners and, focusing on it, the first row of the laminate is mounted.

It is necessary to accurately measure the last of the panels, while noting the cut line on both sides, do not forget to observe the required size for the gap. With the standard laying method, the cut piece is used for the next row.

Do-it-yourself diagonal laminate laying technology

But for diagonal laying, a huge piece would have to be cut off in order to make a new corner. To save material, you simply set aside the cut piece for use in the opposite corner.

The most economical option is styling, which starts from the middle of the room and is directed to the left corner with respect to the incident light rays. For a correct idea of the future location of the panels in the room, definitions with a pattern and an understanding of material consumption, experts recommend estimating on paper a scheme for laying a laminate diagonally.

To begin with, the panels are laid on the left side, after which, on the right, but the first line must be directed to the left corner. The lock laminate is immediately connected with end locks, and then with the next row. Each row is staggered, while maintaining a size of 30 cm between the end joints. In order to avoid bouncing of the panels, any of the edges of the neighboring row is pressed down with a load.

At the final stage of laying, the expansion wedges must be removed. The gap that has formed between the laminate and the wall is covered by the installation of a skirting board, which is attached exclusively to the walls.

With a video and photo of laying a laminate diagonally, you can read in detail a little lower in our article.